User Manual
www.idealight.com.cn
Do your ideal light! What idea you have, what light we have!
www.idealight.com.cn
Professional Moving Head Beam
Order Code: HT-LM-3610QZ
All the products' information accord to the actual lightings' collocation. We will not
inform else if any change. We reserve the final interpretation right.
User Manual
Professional Moving Head Beam
Troubleshooting
Following are a few common problems that may occur during operation.
Contents
Here are some suggestions for easy troubleshooting:
A. The unit does no work, no light
1. Check the connect power and mains fuse.
1. Safety Instruction
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
2. Technical Specfication
1. Check DMX connectors, cables to see if they are linked properly.
2. Check the address settings and DMX polarity.
3. How to Control the Package
3. If you have intermittent DMX signal problems, check the pins on the connectors
or on PCB of the unit or the previous one.
3.1 Control Panel
4. Try to use another DMX controller.
3.2 DMX Control
5. Check to see if the DMX cable run near or run alongside to high voltage cables
3.2.1 DMX 512 Configuration
that may cause damage or interference to DMX interface circuit.
3.2.2 DMX 512 Connection
Professional Moving Head Beam
4. Troubleshooting
Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried
out periodically to optimize light output. Cleaning frequency depends on the
5. Fixture Cleaning
environment in which the fixture operates: damp, smoky or particularly dirty
surrounding can cause greater accumulation of dirt on the unit’s optics.
● Clean with soft cloth using normal glass cleaning fluid.
● Always dry the parts carefully.
● Clean the external optics at least every 20 days. Clean the internal optics at
least every 30/60 days.
5
Professional Moving Head Beam
DMX 512 Connection
Professional Moving Head Beam
Safety
Warning
For your own safety, please read this user manual before operation.
Use universal DMX controller to control the packages, you have to set the DMX
address from 1 to 512 channels so that the unit can receive the DMX signal.
Caution
When switch on the lighting, use the MENU to choose the submenu System
Before operating,make sure the voltage and frequence
Mode, use UP and DOWN to choose DMX 512, press ENTER and then use UP
and DOWN to change the dmx address value. Once the address has been
selected, press ENTER button to store.
of the power supply match the power requirements of the package.
Safety Instructions:
Please keep this User Manual for future consultation. If you sell the unit to
Please find the following examples to address your DMX512 channel for the
another user, be sure that they also receive this instruction booklet.
first 4 packages.
Every person involved with the installation, operation and maintenance should:
14CH Mode:
A001
A015
A029
A043
●
Be competent
18CH Mode:
A001
A019
A037
A055
●
Follow the instructions of this user manual
Caution
Take care using this equipment!
High voltage risk of electric shock.
Before your initial star-up, please make sure that there is no damage caused
during transportation. Should there be any, consult with the dealer and do not use
the unit.
Termination reduces signal errors and to avoid signal transmission problems and
Make sure there are not flammable materials close to the unit while operating
interference. It is always advisable to connect a DMX terminal.
To maintain the equipment in good work condition and to ensure safe operation, it
(Resistance 120ohm 1/4W) between pin2(DMX-) and pin3(DMX+) of the last
is necessary for the user to follow the safety instructions and warning notes
fixture.
written in the manual.
1.If you use a controller with 5 pins DMX output, you have to use a 5 to 3 pin adapter-
Damages caused by user modifications to the unit are not subject to warranty.
cable.
2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.
4
1
Professional Moving Head Beam
Technical Specifations
Professional Moving Head Beam
DMX 512 Configuration
You should find the following items inside the carton packing:
14CH Mode
18CH Mode Function
1pc LED Moving Head, 1set OMEGA clamps, 1pc power cables, 1pc DMX cables,
CH1
CH1
Dimmer
0-255 from 0% to 100%
1pc User Manual
CH2
CH2
Red
0-255 from 0% to 100%
Technical Specifations
CH3
CH3
Green
0-255 from 0% to 100%
Voltage: AC100-240V,50/60HZ
CH4
CH4
Blue
0-255 from 0% to 100%
LEDs: 36pcs 10w RGBW 4IN1 high brightness leds, average life time 50000hours
CH5
CH5
White
0-255 from 0% to 100%
CH6
CH6
Strobe
Power consumption: 360W
Pan: 540degree (8/16bit)
Tilt: 270degree (8/16bit)
Dimmer: 0-100%
Strobe: 0-20times/s
Packing Size: 445*310*435mm
Gross Weight: 11KG
CH7
CH7
Marco
Change; 44~87 Strobe; 88~131
Built-in Programs
Color Fade; 132~219 Mixed
CH8
CH8
Marco Speed
CH9
CH9
Pan
CH10
CH10
Tilt
CH11
CH11
Pan Fine
LCD display: Show the menus and select function by Menu, Up, Down, Enter
CH12
CH12
Tilt Fine
Mains input: Powercon in
CH13
CH13
Pan/Tilt Speed
Professional Moving Head Beam
Control Panel
Switch ON/OFF
CH14
Professional Moving Head Beam
System Mode (DMX 512: DMX address setting / ADJ-W: White balance / EDIT: Manual
SELECT TILT (Tilt reverse)
CHANNEL (Channel Mode: 14CH / 18CH)
->
LANGUAGE
->
Save to Sence
64-127 Pan Movement;
128-191 Tilt Movement;
->
CH15
Pan Movement Angle 0~255 Pan angle from small to big
CH16
Tilt Movement Angle 0~255 Tilt angle from small to big
CH17
XY Silent
0~127 no function;128~255 xy silent
0~192 zoom;
-> SELECT
System Reset
0~255 Speed from fast to slow
192-255 Pan Tilt Movement
Main Functions:
->
Movement
Control Panel
->
0~255 Speed from fast to slow
0-63 No function;
DMX input / output: Use 3-pin XLR cable to link items together
SELECT PAN (Pan reverse)
from slow to fast; 252~255 Full on
program; 220~255 Color Flow
● Sound Activation
mode / SOUND: Sound activation / AUTO: Auto program)
0~2 off; 3~7 on; 8 ~251 Strobe
0~15 No function; 16~43 Color
Operation Modes: ● DMX mode: 14CH/18CH ● Master/Slave mode
● Auto
Value
CH14
CH18
ZOOM/Reset
192~254 zoom from slow to fast;
255 Reset
2
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising