100Series_Manual 8-2-07 - Products For Automation

100Series_Manual 8-2-07 - Products For Automation
100 Series
Media Converter &
Industrial Ethernet Switches
User Manual &
Installation
Guide
8/2/2007
1
Industrial Media Converter Installation Guide
102MC-XX
102MCE-XX-YY
104TX
105TX
108TX
Where: XX = ST or SC and YY = -15, -40, or -80
8/2/2007
2
Copyright, © N-TRON Corp., 2007
820 S. University Blvd., Suite 4E
Mobile, AL USA 36609
All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON
Corp. is prohibited, except as allowed under copyright laws.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos
or other designations mentioned herein are trademarks of their respective owners.
The information contained in this document is subject to change without notice. N-TRON Corp. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any
incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits
arising out of errors or omissions in this manual or the information contained herein.
Contact Information
N-TRON Corp.
820 South University Blvd.
Suite 4E
Mobile, AL 36609
TEL: (251) 342-2164
FAX: (251) 342-6353
Website: www.n-tron.com
Email: support@n-tron.com
8/2/2007
3
GENERAL SAFETY WARNINGS
WARNING: Do not operate the equipment in the presence of flammable gasses or fumes. Operating
electrical equipment in such an environment constitutes a definite safety hazard.
WARNING: If the equipment is used in the manner not specified by N-TRON Corp., the protection provided
by the equipment may be impaired.
WARNING: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.
WARNING:
hazard.
Do not operate the unit with the end plates removed, as this could create a shock or fire
WARNING: Do not operate the equipment in a manner not specified by this manual.
ENVIRONMENTAL SAFETY WARNINGS
WARNING: Disconnect the power and allow to cool 5 minutes before touching.
ELECTRICAL SAFETY WARNINGS
WARNING: Disconnect the power cable before removing the end plates.
WARNING: Do not operate the unit with the end plates removed.
WARNING: Do not work on equipment or cables during periods of lightning activity.
WARNING: Do not perform any services on the unit unless qualified to do so.
WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing voltage
polarity can cause permanent damage to the unit and void the warranty.
8/2/2007
4
HAZARDOUS LOCATION INSTALLATION REQUIREMENTS
1. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or unclassified or nonhazardous locations.
2. WARNING: Explosion Hazard - Substitution of components may impair suitability for Class I,
Division 2.
3. WARNING: Explosion hazard, do not disconnect while the circuit is live or unless the area is known to be
non-hazardous.
4. WARNING: Explosion Hazard - Do not remove or replace the device unless power has been switched off
or the area is known to be non-hazardous.
5. Use 60/75ºC rated Copper wire, (0.22Nm) 2 inch-lbs Tightening torque for field installed connectors.
6. WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.
7. Class I, Div 2 Installations require that power connections must be current limited at the power source with
an in-line fuse rated at 0.5A.
8. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in
which it is installed.
9. Limited Operating Voltage: 12-30V for Class I, Div 2 installations.
8/2/2007
5
100 Series Industrial Ethernet Switches
The 100 Series Unmanaged Industrial Ethernet Switches support high speed layer 2 switching between
ports. This series of switches are housed in a ruggedized aluminum enclosure, and provide Category-5
compliant 10/100-BaseT connections for high performance network design, and hub/repeater upgrades.
The 102MC/MCE is a two port unmanaged media converter that converts 10/100BaseTX copper to
100BaseFX full duplex fiber.
The 104TX, 105TX, and 108TX are affordable and share a small footprint. Each switch is capable of auto
negotiating 10/100 Mb and half/full duplex communications.
The 102MC utilizes the IEEE compliant SC or ST duplex connectors for fiber optic communication. All
10/100Base-TX ports utilize the RJ45 shielded connectors.
Key Features
•
•
•
•
•
•
•
Full IEEE 802.3 & 100Base-FX Compliance
Extended Environmental Specifications
Support for Full/Half Duplex Operation
LED Link/Activity Status Indication
Autonegotiation, Autosensing Speed, Duplex, and Flow Control
Up to 1.0 Gb/s Maximum Throughput
Industry Standard 35mm DIN Rail Mounted Enclosure
8/2/2007
6
PACKAGE CONTENTS
Please make sure the Serial over Ethernet package contains the following items:
1.
2.
100 Series Media Converter or Ethernet Switch
Instruction Sheet
Contact your carrier if any items are damaged.
UNPACKING
Remove all the equipment from the packaging, and store the packaging in a safe place. File any damage
claims with the carrier.
CLEANING
Clean only with a damp cloth.
INSTALLATION
Read the following warning before beginning the installation:
WARNING
Never install or work on electrical equipment or cabling during periods of lightning activity. Never connect
or disconnect power when hazardous gasses are present.
LASER SAFETY (FXE -40 and -80 Only)
WARNING: CLASS 1 LASER PRODUCT. Do not stare into the laser.
8/2/2007
7
DIN-Rail Mounting
Install the unit in a standard DIN rail. Recess the unit to allow at least 2” of horizontal clearance for CAT5e
cable bend radius.
To install the unit to 35mm industrial DIN rail,
place the top edge of the included mounting
bracket on the back of the unit against the DIN
rail at a 15° angle as shown. Rotate the bottom of
the unit to the back (away from you) until it
snaps into place.
To remove the unit from the 35mm industrial
DIN rail, place a flat head screwdriver into the
release clip found at the bottom of the unit, and
apply downward force on the clip until it
disengages from the bottom of the unit from the
DIN rail. Rotate the bottom of the unit towards
you and up at an approximate 15° upward angle
to completely remove the unit.
Most N-Tron™ products are
designed to be mounted on industry
standard 35mm DIN rail. However,
DIN rail mounting may not be
suitable for all applications. Our Rack
Mount Assembly (P/N: 900-RM)
may be used to mount the 102MC
enclosures to standard 19" racks as an
option.
8/2/2007
8
FRONT PANEL
102MC/MCE
From Top to Bottom:
SPD
LNK/ACT
RJ45 Ports
Speed LED
Link/Activity LED
Auto sensing 10/100BaseT Connection
Green LED lights when Power is connected
NOTE: The top LED indicates Link/Activity (LNK/ACT), and the lower LED indicates Speed (SPD) status.
LED’s: The table below describes the operating modes:
LED
LNK/ACT
Color
Description
ON
Power is Applied.
OFF
Power is OFF.
ON
Link established, no Activity on cable.
BLINKING
Link established, Activity on cable
OFF
No link activity on cable.
ON
LINK is 100Mbps.
OFF
Link is 10Mbs.
SPD
8/2/2007
9
APPLYING POWER (Top View)
Unscrew & Remove the DC Voltage Input Plug from the top header.
Install the DC Power Cables into the Plug (observing polarity on unit).
Plug the Voltage Input Plug back into the top header.
Tightening torque for the terminal block power plug is 0.22 Nm/0.162 Pound Foot.
All LED’s will flash ON Momentarily.
Verify the Power LED stays ON (GREEN).
Note: Either V1 or V2 can be connected to power for minimal operation. For redundant power
operation, V1 and V2 plugs must be connected to separate DC Voltage sources. Use wire sizes of 16-28
gauge. The power cord should be limited to less than 10 meters in order to ensure optimum
performance.
Recommended 24V DC Power Supplies, similar to:
100-240VAC:
N-Tron NTPS-24-1.3, DC 24V/1.3A
8/2/2007
10
N-TRON SWITCH GROUNDING TECHNIQUES FOR 100 SERIES
The grounding philosophy of any control system is an integral part of the design. N-Tron switches are designed
to be grounded, but the user has been given the flexibility to float the switch when required. The best noise
immunity and emissions (i.e. CE) are obtained when the N-Tron switch chassis is connected to earth ground via
a drain wire. Some N-Tron switches have metal din-rail brackets that can ground the switch if the din-rail is
grounded. In some cases, N-Tron switches with metal brackets can be supplied with optional plastic brackets if
isolation is required.
Users may run a drain wire & lug from the screw provided on the back face of the
enclosure. In the event the provided grounding screw has been lost, care should
be taken to limit the penetration of the outer skin by less than 1/4". Failure to do
so may cause irreversible damage to the internal components of the switch.
Note: Ensure the power supply is grounded properly before applying power to the
grounded switch. This may be verified by using a voltmeter to determine that
there is no voltage difference between the power supply’s negative output terminal
and the chassis grounding point of the switch.
As an alternative grounding method, both V- legs of the power input
connector are connected to chassis internally on the PCB. Connecting
a drain wire to earth ground from one of the V- terminal plugs as
shown here will ground the switch and the chassis. The power leads
from the power source should be limited to 3 meters or less in length.
The use of shielded cables between devices is not required for most N-Tron devices (please consult the user
manuals for specific details). If the use of shielded cables is required, it is generally recommended to only
connect the shield at one end to prevent ground loops and interfere with low level signals (i.e. thermocouples,
RTD, etc.). Cat5e cables manufactured to EIA-568A or 568B specifications are required for use with N-Tron
Switches.
In the event all Cat5e patch cable distances are small (i.e. All Ethernet devices are located the same local
cabinet and/or referenced to the same earth ground), it is permissible to use fully shielded cables terminated to
chassis ground at both ends in systems void of low level analog signals.
8/2/2007
11
RJ45 CONNECTOR CRIMP SPECIFICATIONS
Please reference the illustration below for your Cat5 cable specifications:
8/2/2007
12
CONNECTING THE UNIT
For the 100BaseFX Fiber Optic port, remove the dust cap(s) from the fiber optic connector and connect the
fiber optic cables. The TX port on the local unit should be connected to the RX port of the far end device, and
the RX port should be connected to the TX port of the far end device.
For 10Base-T ports, plug a Category 3 (or greater) twisted pair cable into the RJ45 connector. For
100Base-T ports, plug a Category 5 (or greater) twisted pair cable into the RJ45 connector. Connect the
other end to the far end station. Verify that the LNK LED’s are ON once the connection has been
completed. To connect any other port to another Switch or Repeater, use a standard Cat5 straight through or
crossover cable.
TROUBLESHOOTING
1. Make sure the
(Power LED) is ON.
2. Make sure you are supplying sufficient current for the version chosen. Note: The Inrush current will
exceed the steady state current by ~ 2X.
3. Verify that Link LED’s are ON for both ports.
4. Verify cabling used between stations.
5. Verify that cabling is Category 3 or greater for 10Mbit Operation.
SUPPORT
Contact N-TRON Corp. at:
TEL: 251-342-2164
FAX: 251-342-6353
www.n-tron.com
support@n-tron.com
8/2/2007
13
FCC STATEMENT
This product complies with Part 15 of the FCC-A Rules.
Operation is subject to the following conditions:
(1) This device may not cause harmful Interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this device in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
INDUSTRY CANADA
This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulations. Operation is subject to the following two conditions; (1) this device digital apparatus meets all
requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the
following two conditions; (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant
des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne
pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y
compris l'interférence qui peut causer l'opération peu désirée.
8/2/2007
14
Regulatory Approvals:
Safety: UL Listed per ANSI/ISA-12.12.01-2000 (US and Canada)
This apparatus is suitable for use in Class I, Div 2, Groups A, B, C, and D
UL Temperature Ratings: 102MC/MCE - T5
104TX, 105TX, and 108TX - T4A
EMI: EN61000-6-4, EN55011 - Class A
FCC Title 47, Part 15, Subpart B - Class A
ICES-003 – Class A
EMS: EN61000-6-2
EN61000-4-2 (ESD)
EN61000-4-3 (RS)
EN61000-4-4 (EFT)
EN61000-4-5 (Surge)
EN61000-4-6 (Conducted Disturbances)
Warranty: 1 year from the date of purchase.
8/2/2007
15
102MC/MCE - KEY SPECIFICATIONS
Physical
Height:
Width:
Depth Including Din-Rail Clip:
Weight:
2.90” (max.)
1.50” (max.)
4.82” (max.)
0.60 lbs.
Electrical
Input Voltage:
Input Current:
Inrush Current:
Input Ripple:
Input Wire Size:
10-30 VDC (Regulated)
40mA max. @ 24VDC (Steady State)
8.5Amp/0.7 ms max. @ 24VDC
Less than 100 mV
16-28 AWG
1
Environmental
Operating Temperature:
Storage Temperature:
Operating Humidity:
Operating Altitude:
Network Media
10BaseT:
100BaseT:
100BaseFX:
-40°C to 80°C
-40°C to 85°C
10% to 90% (Non Condensing)
0 to 10,000 ft.
> Cat-3 Cable
> Cat-5 Cable
Multimode: 50-62.5/125µm Fiber
Singlemode: 7-9/125µm Fiber
Fiber Transceiver Characteristics
Fiber Length:
2km*
TX Power Min/Max
-19dBm/-14dBm -15dBm/-7dBm 5dBm/0dBm
15km**
40km**
80km**
-5dBm/0dBm
RX Sensitivity Max: -32dBm
-34dBm
-34dBm
-34dBm
Wavelength:
1310nm
*=Multimode ** =Singlemode
1310nm
1310nm
1550nm
Connectors
10/100BaseTX:
100BaseFX:
RJ45 UTP Port
SC or ST Duplex Port
Recommended Minimum Wiring Clearance:
Front: 5” (12.7 cm)
Top: 1" (2.54 cm)
8/2/2007
16
104TX/105TX - KEY SPECIFICATIONS
Physical
Height:
Width:
Depth:
Weight:
2.9” (max.)
1.50” (max.)
4.25” (max.)
0.60 lbs.
Electrical
Input Voltage:
Input Current:
Inrush Current:
Input Ripple:
Input Wire Size:
10-30 VDC (Regulated)
215 mA max. @ 24VDC (Steady State)
7.8 Amp/0.7ms max. @ 24VDC
Less than 100 mV
16-28 AWG
Environmental
Operating Temperature:
Storage Temperature:
Operating Humidity:
Operating Altitude:
Network Media
10BaseT:
100BaseT:
-40°C to 80°C
-40°C to 85°C
10% to 90% (Non Condensing)
0 to 10,000 ft.
> Cat-3 Cable
> Cat-5 Cable
Connectors
10/100BaseT: RJ45 UTP Ports
Recommended Minimum Wiring Clearance:
Top: 2" (5.08 cm)
Front: 2" (5.08 cm)
Side: 1" (2.54 cm)
Warranty: 1 year from the date of purchase.
8/2/2007
17
108TX - KEY SPECIFICATIONS
Physical
Height:
Width:
Depth Including DIN Rail Clip:
Weight:
DIN Rail
3.5” (8.89 cm)
1.50” (3.81 cm)
4.22” (10.7 cm)
0.64 lbs. (0.29 kg)
35 mm
Electrical
Input Voltage:
Input Current:
Inrush Current:
Input Ripple:
Input Wire Size:
10-30 VDC (Regulated)
250 mA max. @ 24VDC (Steady State)
8.1 Amp/0.7ms max. @ 24VDC
Less than 100 mV
16-28 AWG
Environmental
Operating Temperature:
Storage Temperature:
Operating Humidity:
Operating Altitude:
-40°C to 70°C
-40°C to 85°C
10% to 90% (Non Condensing)
0 to 10,000 ft.
Network Media
10BaseT:
100BaseT:
> Cat-3 Cable
> Cat-5 Cable
Connectors
10/100BaseT:
Eight (8) RJ45 UTP Ports
Recommended Minimum Wiring Clearance:
Top: 2" (5.08 cm)
Front: 2" (5.08 cm)
8/2/2007
18
N-TRON Limited Warranty
N-TRON, Corp. warrants to the end user that this hardware product will be free from defects in workmanship and materials, under normal use
and service, for the applicable warranty period from the date of purchase from N-TRON or its authorized reseller. If a product does not operate
as warranted during the applicable warranty period, N-TRON shall, at its option and expense, repair the defective product or part, deliver to
customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product. All
products that are replaced will become the property of N-TRON. Replacement products may be new or reconditioned. Any replaced or repaired
product or part has a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer. N-TRON shall not be
responsible for any custom software or firmware, configuration information, or memory data of customer contained in, stored on, or integrated
with any products returned to N-TRON pursuant to any warranty.
OBTAINING WARRANTY SERVICE: Customer must contact N-TRON within the applicable warranty period to obtain warranty service
authorization. Dated proof of purchase from N-TRON or its authorized reseller may be required. Products returned to N-TRON must be preauthorized by N-TRON with a Return Material Authorization (RMA) number marked on the outside of the package, and sent prepaid and
packaged appropriately for safe shipment. Responsibility for loss or damage does not transfer to N-TRON until the returned item is received by
N-TRON. The repaired or replaced item will be shipped to the customer, at N-TRON’s expense, not later than thirty (30) days after N-TRON
receives the product. N-TRON shall not be responsible for any software, firmware, information, or memory date of customer contained in,
stored on, or integrated with any products returned to N-TRON for repair, whether under warranty or not.
ADVANCE REPLACEMENT OPTION: Upon registration, this product qualifies for advance replacement. A replacement product will be
shipped within three (3) days after verification by N-TRON that the product is considered defective. The shipment of advance replacement
products is subject to local legal requirements and may not be available in all locations. When an advance replacement is provided and
customer fails to return the original product to N-TRON within fifteen (15) days after shipment of the replacement, N-TRON will charge
customer for the replacement product, at list price.
WARRANTIES EXCLUSIVE: IF AN N-TRON PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE
REMEDY FOR BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE
PAID, AT N-TRON'S OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REMEDIES
ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER
IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS, OR CONDITIONS OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH
DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. N-TRON NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. N-TRON SHALL NOT BE LIABLE UNDER THIS WARRANTY IF
ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE PRODUCT DOES NOT
EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR
TESTING, UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY OTHER CAUSE BEYOND THE
RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, POWER CUTS OR OUTAGES, OTHER HAZARDS, OR
ACTS OF GOD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, N-TRON ALSO EXCLUDES FOR ITSELF AND ITS
SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS,
LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS,
EVEN IF N-TRON OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND
LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT N-TRON'S OPTION. THIS
DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF
ITS ESSENTIAL PURPOSE.
DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or limitation of implied warranties or the limitation of incidental
or consequential damages for certain products supplied to consumers or the limitation of liability for personal injury, so the above limitations
and exclusions may be limited in their application to you. When the implied warranties are not allowed to be excluded in their entirety, they will
be limited to the duration of the applicable written warranty. This warranty gives you specific legal rights which may vary depending on local
law.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the State of Alabama, U.S.A.
8/2/2007
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising