Garmin Software Version 0464.08 Cockpit Reference Guide

Add to my manuals
128 Pages

advertisement

Garmin Software Version 0464.08 Cockpit Reference Guide | Manualzz

Integrated Flight Deck

Cockpit Reference Guide

Beechcraft

A36/G36

Copyright © 2005-2007 Garmin Ltd. or its subsidiaries. All rights reserved.

This manual reflects the operation of System Software version 0464.08 or later for the Beechcraft A36/G36. Some differences in operation may be observed when comparing the information in this manual to earlier or later software versions.

Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.

Tel: 913/397.8200 Fax: 913/397.8282

Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.

Tel: 503/391.3411 Fax 503/364.2138

Garmin (Europe) Ltd, Liberty House, Bulls Copse Road, Hounsdown Business Park, Southampton, SO40 9RB, U.K.

Tel: 44/0870.8501241 Fax: 44/0870.8501251

Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan

Tel: 886/02.2642.9199 Fax: 886/02.2642.9099

Web Site Address: www.garmin.com

Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express written permission of Garmin. Garmin hereby grants permission to download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage medium to be viewed for personal use, provided that such electronic or printed copy of this manual or revision must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Garmin ® and G1000 ® are registered trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

NavData ® is a registered trademark of Jeppesen, Inc.; Stormscope ® and SkyWatch ® are registered trademarks of L-3

Communications; and XM ® is a registered trademark of XM Satellite Radio, Inc.;

September 2007 190-00525-01 Rev. B

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Printed in the U.S.A

WARNINGS,

CAUTIONS, & NOTES

.

WARNING: Navigation and terrain separation must NOT be predicated upon the use of the terrain function.

The G1000 Terrain Proximity feature is NOT intended to be used as a primary reference for terrain avoidance and does not relieve the pilot from the responsibility of being aware of surroundings during flight. The Terrain

Proximity feature is only to be used as an aid for terrain avoidance and is not certified for use in applications requiring a certified terrain awareness system. Terrain data is obtained from third party sources. Garmin is not able to independently verify the accuracy of the terrain data.

WARNING: The displayed minimum safe altitudes (MSAs) are only advisory in nature and should not be relied upon as the sole source of obstacle and terrain avoidance information. Always refer to current aeronautical charts for appropriate minimum clearance altitudes.

WARNING: The altitude calculated by G1000 GPS receivers is geometric height above Mean Sea Level and could vary significantly from the altitude displayed by pressure altimeters, such as the GDC 74A Air Data Computer, or other altimeters in aircraft. GPS altitude should never be used for vertical navigation. Always use pressure altitude displayed by the G1000 PFD or other pressure altimeters in aircraft.

WARNING: Do not use outdated database information. Databases used in the G1000 system must be updated regularly in order to ensure that the information remains current. Pilots using any outdated database do so entirely at their own risk.

WARNING: Do not use basemap (land and water data) information for primary navigation. Basemap data is intended only to supplement other approved navigation data sources and should be considered as an aid to enhance situational awareness.

WARNING: Traffic information shown on the G1000 Multi Function Display is provided as an aid in visually acquiring traffic. Pilots must maneuver the aircraft based only upon ATC guidance or positive visual acquisition of conflicting traffic.

WARNING: Use of the Stormscope is not intended for hazardous weather penetration (thunderstorm penetration).

Stormscope information, as displayed on the G1000 MFD, is to be used only for weather avoidance, not penetration.

WARNING: GDL 69 Weather should not be used for hazardous weather penetration. Weather information provided by the GDL 69 is approved only for weather avoidance, not penetration.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

WARNINGS,

CAUTIONS, & NOTES

WARNING: NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delays in data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range weather avoidance.

WARNING: The Garmin G1000, as installed in the Beechcraft A36/G36 aircraft, has a very high degree of functional integrity. However, the pilot must recognize that providing monitoring and/or self-test capability for all conceivable system failures is not practical. Although unlikely, it may be possible for erroneous operation to occur without a fault indication shown by the G1000. It is thus the responsibility of the pilot to detect such an occurrence by means of cross-checking with all redundant or correlated information available in the cockpit.

WARNING: For safety reasons, G1000 operational procedures must be learned on the ground.

WARNING: The United States government operates the Global Positioning System and is solely responsible for its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and performance of all GPS equipment. Portions of the Garmin G1000 utilize GPS as a precision electronic

NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the G1000 can be misused or misinterpreted and, therefore, become unsafe.

WARNING: To reduce the risk of unsafe operation, carefully review and understand all aspects of the G1000

Pilot’s Guide documentation and the Beechcraft A36/G36 Pilot’s Operating Handbook. Thoroughly practice basic operation prior to actual use. During flight operations, carefully compare indications from the G1000 to all available navigation sources, including the information from other NAVAIDs, visual sightings, charts, etc.

For safety purposes, always resolve any discrepancies before continuing navigation.

WARNING: The illustrations in this guide are only examples. Never use the G1000 to attempt to penetrate a thunderstorm. Both the FAA Advisory Circular, Subject: Thunderstorms, and the Airman’s Information Manual

(AIM) recommend avoiding “by at least 20 miles any thunderstorm identified as severe or giving an intense radar echo.”

CAUTION: The GDU 1040 PFD and GDU 1043 MFD displays use a lens coated with a special anti-reflective coating that is very sensitive to skin oils, waxes, and abrasive cleaners. CLEANERS CONTAINING AMMONIA

WILL HARM THE ANTI-REFLECTIVE COATING. It is very important to clean the lens using a clean, lint-free cloth and an eyeglass lens cleaner that is specified as safe for anti-reflective coatings.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

WARNINGS,

CAUTIONS, & NOTES

CAUTION: The Garmin G1000 does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and the pilot’s authority to operate this device under FAA/FCC regulations.

NOTE: When using Stormscope, there are several atmospheric phenomena in addition to nearby thunderstorms that can cause isolated discharge points in the strike display mode. However, clusters of two or more discharge points in the strike display mode do indicate thunderstorm activity if these points reappear after the screen has been cleared.

NOTE: All visual depictions contained within this document, including screen images of the G1000 panel and displays, are subject to change and may not reflect the most current G1000 system. Depictions of equipment may differ slightly from the actual equipment.

NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s

Proposition 65. If you have any questions or would like additional information, please refer to our web site at www.garmin.com/prop65.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

RECORD OF REVISIONS

Part Number

190-00525-00 Initial release.

190-00525-01

Rev A

Change Summary

Added GDU software version 6.13 parameters.

Added TAWS

Revision Date of Revision Affected Pages

B 9/07 Copyright Page

Description

Changed system software number to

0464.08.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

RR-1

RECORD OF REVISIONS

Blank Page

RR-2

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

TABLE OF CONTENTS

SECTION 1: SYSTEM OVERVIEW

.................................... 1-1

1.1 PFD/MFD Controls ...................................................1-2

1.2 PFD Softkeys ............................................................1-4

1.3 MFD Softkeys ..........................................................1-7

1.4 MFD Page Groups ...................................................1-8

1.5 Backlighting .............................................................1-8

1.6 Database Updates ..................................................1-9

Aviation Database Update ........................................... 1-9

Terrain and Obstacle Database Updates ....................... 1-9

SECTION 2: FLIGHT INSTRUMENTS

.............................. 2-1

2.1 Airspeed Indicator ..................................................2-3

Speed Indication ......................................................... 2-3

Speed Ranges ............................................................. 2-3

Airspeed Trend Vector ................................................. 2-3

Vspeed References ...................................................... 2-3

2.2 Attitude Indicator ..................................................2-3

2.3 Altimeter ..................................................................2-4

Altitude Select Bug ...................................................... 2-4

Altitude Trend Vector ................................................... 2-4

Barometric Setting Box ................................................ 2-4

Altitude Alerting .......................................................... 2-4

Barometric Minimum Descent Altitude ......................... 2-4

2.4 Vertical Deviation/Glideslope Indicator ............2-5

2.5 Marker Beacon Annunciations ............................2-5

2.6 Vertical Speed Indicator .......................................2-5

2.7 Horizontal Situation Indicator (HSI) ...................2-6

Course Pointer ............................................................ 2-6

Course Deviation Indicator (CDI) .................................. 2-7

Bearing Pointers and Information Windows .................. 2-7

DME (optional) ............................................................ 2-7

Navigation Source ....................................................... 2-7

SECTION 3: ENGINE INDICATION SYSTEM (EIS)

.... 3-1

3.1 Engine Display .........................................................3-1

3.2 Lean Engine Display ...............................................3-1

3.3 Engine System Display ..........................................3-2

SECTION 4: NAV/COM AND TRANSPONDER

.......... 4-1

4.1 Radio Status Indications .......................................4-3

4.2 Volume ......................................................................4-3

4.3 Automatic Squelch .................................................4-3

4.4 Quickly Activating 121.500 MHz ..........................4-3

4.5 Optional NAV Radios .............................................4-3

DME Radio (optional) .................................................. 4-3

4.6 Frequency Auto-tuning .........................................4-4

Auto-tuning on the PFD .............................................. 4-4

Auto-tuning on the MFD ............................................. 4-4

4.7 Transponder .............................................................4-4

Mode Selection ........................................................... 4-4

Ground Mode (Automatic) ......................................4-4

Reply Status ...........................................................4-4

Code Selection .......................................................4-4

Flight ID Reporting ...................................................... 4-5

SECTION 5: AUDIO PANEL

................................................ 5-1

5.1 COM Radio Selection .............................................5-2

5.2 Marker Beacon Receiver .......................................5-2

Marker Beacon Signal Sensitivity ................................. 5-2

5.3 Nav Radio Audio Selection ...................................5-2

5.4 Intercom System (ICS) Isolation ..........................5-3

5.5 Intercom Squelch Control .....................................5-3

5.6 Digital Clearance Recorder and Playback .........5-4

SECTION 6: AUTOMATIC FLIGHT CONTROL

............. 6-1

6.1 Mode Annunciations ..............................................6-1

6.2 Overspeed Protection ...........................................6-2

6.3 AP Engagement/Disengagement ........................6-2

Automatic Disengagement .......................................... 6-3

Manual Disengagement .............................................. 6-3

Control Wheel Steering ................................................ 6-3

Yaw Damper ............................................................... 6-3

6.4 Loss of Data .............................................................6-3

6.5 Pitch Axis Modes ....................................................6-3

Pitch Hold Mode (PIT) ................................................. 6-4

Altitude Hold Mode (ALT) ............................................ 6-5

Vertical Speed Mode (VS) ............................................ 6-6

Flight Level Change Mode (FLC) .................................. 6-7

Go-Around Mode (GA) ................................................ 6-8

Glideslope (GS) ........................................................... 6-8

6.6 Roll Axis Modes .......................................................6-9

Roll Hold Mode (ROL) .................................................. 6-9

Heading Select Mode (HDG) ...................................... 6-10

Navigation Mode (GPS, VOR, LOC, or BC) ................... 6-11

Navigation Mode Armed .......................................6-11

Approach Mode (GPS, VAPP or LOC) .......................... 6-12

Go Around (GA) ........................................................ 6-12

6.7 Example Procedures Using AFCS .......................6-13

Departure ................................................................. 6-14

Intercepting a VOR Radial .......................................... 6-15

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36 i

ii

TABLE OF CONTENTS

Flying a GPS Flight Plan ............................................. 6-16

Flight Level Change (Descent) .................................... 6-17

ILS Approach ............................................................. 6-18

Go-Around / Missed Approach ................................... 6-19

SECTION 7: NAVIGATION

.................................................. 7-1

7.1 Navigation Map Page ............................................7-1

Select the MAP Page Group ......................................... 7-1

7.2 Direct-to Navigation ..............................................7-1

Direct-to Navigation from the MFD .............................. 7-1

Direct-to Navigation from the PFD ............................... 7-2

7.3 Airport Information ...............................................7-3

Select the Airport Information Page ............................. 7-3

Enter a Waypoint Facility Name or City Location ........... 7-3

Access Runway Information ......................................... 7-3

Access Frequency Information ...................................... 7-3

7.4 Intersection Information ......................................7-4

Select the Intersection Information Page ...................... 7-4

Access Information on an Intersection ......................... 7-4

7.5 NDB Information .....................................................7-4

Select the NDB Information Page ................................. 7-4

View Information on a Specific NDB ............................ 7-4

7.6 VOR Information .....................................................7-5

Select the VOR Information Page ................................. 7-5

Access Information on a VOR ....................................... 7-5

7.7 User Waypoint Information Page .......................7-5

7.8 Nearest Airports .....................................................7-5

Nearest Airport Information on the MFD ...................... 7-5

Nearest Airports Information on the PFD ...................... 7-6

7.9 Nearest Intersections ............................................7-6

Select the Nearest Intersections Page ........................... 7-6

View Information on the Nearest Intersection .............. 7-7

7.10 Nearest NDB ............................................................7-7

Select the Nearest NDB Page ....................................... 7-7

Access Information on a Specific NDB .......................... 7-7

7.11 Nearest VOR .............................................................7-7

Select the Nearest VOR Page ....................................... 7-7

View Information on the Nearest VOR .......................... 7-7

Select and Load a VOR Frequency ................................ 7-8

7.12 Nearest User Waypoint ..........................................7-8

Select the Nearest User Waypoint Page ........................ 7-8

Select a Nearest User Waypoint ................................... 7-8

7.13 Nearest Frequencies ..............................................7-8

Select the Nearest Frequencies Page ............................ 7-8

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Select and Load the Nearest ARTCC, FSS, or Weather

Frequency ................................................................... 7-9

7.14 Nearest Airspaces ...................................................7-9

Select the Nearest Airspaces Page ................................ 7-9

Airspace Alerts Box ..................................................... 7-9

View Additional Details for a Listed Airspace ................ 7-9

View and Quickly Load the Frequency for a

Controlling Agency ...................................................... 7-9

SECTION 8: FLIGHT PLANNING

...................................... 8-1

8.1 User Defined Waypoints ........................................8-1

Select the User WPT Information Page ......................... 8-1

Create a New User Waypoint ....................................... 8-1

Create User Waypoints from the Navigation Map Page . 8-1

Modify a User Waypoint .............................................. 8-2

Delete a User Waypoint ............................................... 8-2

8.2 Viewing the Active Flight Plan ............................8-2

8.3 Activate a Stored Flight Plan ...............................8-2

8.4 Activate a Flight Plan Leg ....................................8-3

8.5 Stop Navigating a Flight Plan ..............................8-3

8.6 Invert Active Flight Plan .......................................8-3

8.7 Create a New Flight Plan ......................................8-3

8.8 Load a Departure ...................................................8-4

8.9 Load an Arrival ........................................................8-4

8.10 Load an Approach ..................................................8-5

8.11 Remove a Departure, Arrival, or Approach from a Flight Plan ...................................................8-5

8.12 Store a Flight Plan ..................................................8-5

8.13 Edit a Stored Flight Plan .......................................8-5

8.14 Delete a Waypoint from the Flight Plan ............8-5

8.15 Invert and Activate a Stored Flight Plan ..........8-6

8.16 Copy a Flight Plan ..................................................8-6

8.17 Delete a Flight Plan ...............................................8-6

8.18 Graphical Flight Plan Creation ............................8-6

8.19 Trip Planning ............................................................8-7

8.20 Vertical Navigation (VNAV) Page ........................8-8

Create a Vertical Navigation Profile .............................. 8-8

VNAV Page Menu Options ........................................... 8-9

SECTION 9: PROCEDURES

................................................ 9-1

9.1 Arrivals and Departures ........................................9-1

Load and Activate a Departure Procedure .................... 9-1

Load and Activate An Arrival Procedure ........................ 9-1

TABLE OF CONTENTS

9.2 Approaches ..............................................................9-2

Load and/or Activate an Approach Procedure ............... 9-2

Activate An Approach in the Active Flight Plan ............. 9-3

SECTION 10: HAZARD AVOIDANCE

........................... 10-1

10.1 Customizing the Hazard Displays on the

Navigation Map ....................................................10-1

10.2 Stormscope® (Optional) .....................................10-1

Displaying Stormscope Lightning Data on the

Navigation Map Page ................................................ 10-1

Stormscope Page ....................................................... 10-2

10.3 XM Weather (Optional) .......................................10-3

Displaying METAR and TAF information on the

Airport Information Page ........................................... 10-3

Displaying Weather on the Weather Data Link Page ... 10-4

NEXRAD Limitations .............................................10-4

Map Panning Information – Weather Data Link Page . 10-5

Weather Products and Symbols ................................. 10-5

Weather Product Age ................................................ 10-6

10.4 Traffic Information Service (TIS) .......................10-7

Displaying Traffic on the Traffic Map Page ................... 10-7

Displaying Traffic on the Navigation Map ................... 10-7

TIS Audio Alert .......................................................... 10-7

10.5 Skywatch Traffic Advisory System(TAS)

(Optional) ...............................................................10-8

Displaying Traffic on the Traffic Map Page ................... 10-8

Displaying Traffic on the Navigation Map ................... 10-8

10.6 Terrain And Obstacle Proximity ........................10-9

Displaying Terrain and Obstacles on the Terrain

Proximity Page .......................................................... 10-9

Displaying Terrain and Obstacles on the Navigation

Map .......................................................................... 10-9

10.7 Terrain Awareness & Warning System (TAWS)

Display (Optional) ...............................................10-10

Displaying Terrain on the TAWS Page ....................... 10-10

Enable/Disable Aviation Data ................................... 10-11

TAWS Inhibit ........................................................... 10-11

Manual System Test ................................................. 10-12

Forward Looking Terrain Avoidance (FLTA) ................ 10-12

Reduced Required Terrain Clearance (RTC) and

Reduced Required Obstacle Clearance (ROC) ......10-12

Imminent Terrain Impact (ITI) and Imminent

Obstacle Impact (IOI) ..........................................10-12

Premature Descent Alert (PDA) ................................ 10-12

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Excessive Descent Rate Alert (EDR) .......................... 10-13

Negative Climb Rate After TakeoffAlert (NCR) .......... 10-13

“Five-Hundred” Aural Alert ...................................... 10-13

Displaying Terrain and Obstacles on the

Navigation Map ...................................................... 10-14

Pop-up Alerts .......................................................... 10-14

TAWS Alerts Summary ............................................. 10-15

Alert Annunciations ................................................. 10-16

SECTION 11: ABNORMAL OPERATION

..................... 11-1

11.1 Reversionary Mode ..............................................11-1

11.2 Abnormal COM Operation ..................................11-2

11.3 Unusual Attitudes .................................................11-2

11.4 Stormscope Operation with Loss of

Heading Input ........................................................11-2

11.5 Hazard Displays with Loss of GPS Position ....11-2

SECTION 12: ANNUNCIATIONS & ALERTS

.............. 12-1

12.1 Alert Level Definitions ........................................12-2

12.2 A36/G36 Aircraft Annunciations & Alerts ........12-3

WARNING Annunciation ............................................ 12-3

CAUTION Annunciation ............................................. 12-3

ADVISORY Annunciation ............................................ 12-3

Alert Message ........................................................... 12-3

12.3 AFCS Alerts .............................................................12-4

System Status Field ................................................... 12-4

12.4 TAWS ALERTS .........................................................12-5

TAWS System Status Annunciations ........................... 12-6

12.5 Traffic Voice Alerts ...............................................12-6

12.6 G1000 System Annunciations ............................12-6

12.7 G1000 System Alert Messages ...........................12-9

MFD & PFD Message Advisories ............................... 12-10

Database Message Advisories .................................. 12-11

GMA 1347 Message Advisories ............................... 12-12

GIA 63 Message Advisories ..................................... 12-12

GEA 71 Message Advisories .................................... 12-14

GTX 33 Message Advisories ..................................... 12-15

GRS 77 Message Advisories ..................................... 12-15

GMU 44 Message Advisories ................................... 12-16

GDL 69 Message Advisories ..................................... 12-16

GDC 74A Message Advisories .................................. 12-16

Miscellaneous Message Advisories ........................... 12-17

Index

.....................................................................................Index-1

iii

TABLE OF CONTENTS

Blank Page iv

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 1

SYSTEM OVERVIEW

SECTION 1: SYSTEM OVERVIEW

The purpose of this Cockpit Reference Guide is to provide the pilot a resource with which to find operating instructions on the major features of the G1000 system more easily. It is not intended to be a comprehensive operating guide. Complete operating procedures for the complete system are found in the G1000 Pilot’s Guide, part number 190-00595-00

This guide gives the pilot abbreviated operating instructions for the Primary Flight Display (PFD), Multi

Function Display (MFD), and the GMA 1347 Audio Panel

System.

NOTE: The pilot should read and thoroughly understand the Beechcraft A36/G36 Pilot’s

Operating Handbook (POH) for limitations, procedures and operational information not contained in this Cockpit Reference Guide.

The Beechcraft A36/G36 POH always takes precedence over the information found in this guide.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 1

SYSTEM OVERVIEW

1.1 PFD/MFD CONTROLS

1 2 3 4 5 6 7 8 9

1-2

18

19

20

21

22

23

17

24

25

26

Figure 1-1 PFD/MFD Controls

10

11

12

27

28

13

MFD Only

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

14

15

16

SECTION 1

SYSTEM OVERVIEW

PFD and MFD controls function the same with the exception of the dedicated Automatic Flight Control

System (AFCS) keys located only on the MFD bezel.

(1) NAV VOL/ID Knob – Controls the NAV audio level.

Press to turn the Morse code identifier ON and OFF.

Volume level is shown in the field as a percentage.

(2) NAV Frequency Transfer Key – Switches the standby and active NAV frequencies.

(3) Dual NAV Knob – Tunes the MHz (large knob) and kHz (small knob) standby frequencies for the NAV receiver. Press to switch the tuning cursor (light blue box) between the NAV1 and NAV2 fields.

(4) Heading Knob – Turn to manually select a heading on the HSI. When pressed, it synchronizes the heading bug with the compass lubber line. Selected Heading provides the heading reference to the Flight Director while operating in Heading Select mode.

(5) Joystick – Changes the map range (distance top to bottom of map display) when rotated. Activates the map pointer when pressed.

(6) CRS/BARO Knob – The large knob sets the altimeter barometric pressure and the small knob adjusts the course. The course is only adjustable when the HSI is in

VOR1, VOR2, or OBS/SUSP mode. Pressing this knob centers the CDI on the currently selected VOR. Selected

Course provides course reference to the Flight Director when operating in Navigation and Approach modes.

(7) Dual COM Knob – Tunes the MHz (large knob) and kHz (small knob) standby frequencies for the COM transceiver. Pressing this knob switches the tuning cursor

(light blue box) between the COM1 and COM2 fields.

(8) COM Frequency Transfer Key – Switches the standby and active COM frequencies. Pressing and holding this key for two seconds automatically tunes the emergency frequency (121.5 MHz) in the active frequency field.

(9) COM VOL/SQ Knob – Controls COM audio level.

Pressing this knob turns the COM automatic squelch ON and OFF. Audio volume level is shown in the field as a percentage.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

(10) Direct-to Key – Allows the user to enter a destination waypoint and establish a direct course to the selected destination (specified by the identifier, chosen from the active route, or taken from the map cursor position).

(11) FPL Key – Displays the active Flight Plan Page for creating and editing the active flight plan, or for accessing stored flight plans.

(12) CLR Key (DFLT MAP) – Erases information, cancels an entry, or removes page menus. To display the

Navigation Map Page immediately, press and hold CLR

(MFD only).

(13) Dual FMS Knob – Used to select the page to be viewed (only on the MFD). The large knob selects a page group (MAP, WPT, AUX, NRST), while the small knob selects a specific page within the page group. Pressing the small knob turns the selection cursor ON and OFF. When the cursor is ON, data may be entered in the different windows using the small and large knobs. The large knob is used to move the cursor on the page, while the small knob is used to select individual characters for the highlighted cursor location. When the G1000 displays a list that is too long for the display screen, a scroll bar appears along the right side of the display, indicating the availability of additional items within the selected category.

Press the FMS/PUSH CRSR Knob to activate the cursor and turn the large FMS Knob to scroll through the list.

(14) MENU Key – Displays a context-sensitive list of options. This list allows the user to access additional features, or to make setting changes that relate to certain pages.

(15) PROC Key – Selects approaches, departures and arrivals from the flight plan. If a flight plan is used, available procedures for the departure and/or arrival airport are automatically suggested. If a flight plan is not used, the desired airport and the desired procedure may be selected. This key selects IFR departure procedures (DPs), arrival procedures (STARs) and approaches (IAPs) from the database and loads them into the active flight plan.

1-3

1-4

SECTION 1

SYSTEM OVERVIEW

(16) ENT Key – Accepts a menu selection or data entry.

This key is used to approve an operation or complete data entry. It is also used to confirm selections and information entries.

(17) Dual ALT Knob – Sets the reference altitude in the box located above the Altimeter. The large knob selects the thousands, while the small knob selects the hundreds.

Selected altitude provides an altitude setting for the

Altitude Capture/Hold mode, in addition to the standard

G1000 altitude alerter function.

(18) AP Key – Engages/disengages the Autopilot and

Flight Director. Pressing the AP Key activates the Flight

Director and engages the Autopilot in the default pitch axis and roll axis modes. Pressing the AP Key again disengages the autopilot and deactivates the Flight Director.

(19) FD Key – Activates/deactivates the Flight Director only. Pressing the FD Key turns on the Flight Director in the default pitch axis and roll axis modes. Pressing the

FD Key again deactivates the Flight Director and removes the command bars, unless the Autopilot is engaged. If the

Autopilot is engaged, the FD Key is disabled.

(20) NAV Key – Selects/deselects the Navigation mode.

(21) ALT Key – Selects/deselects the Altitude Hold mode.

(22) VS Key – Selects/deselects the Vertical Speed mode.

(23) FLC Key – Selects/deselects the Flight Level Change mode.

(24) YD Key – Engages/disengages the Yaw Damper.

(25) HDG Key – Selects/deselects the Heading Select mode.

(26) APR Key – Selects/deselects the Approach mode.

(27, 28) NOSE UP/NOSE DN Keys – Controls the active pitch reference for the Pitch Hold, Vertical Speed, and Flight Level Change modes.

1.2 PFD SOFTKEYS

Softkey ON Softkey OFF

Figure 1-2 PFD Top Level Softkeys

INSET – Press to display the Inset Map in the lower left corner of the PFD.

OFF – Press to remove the Inset Map.

DCLTR (3) – Press momentarily to select the desired amount of map detail. The declutter level appears adjacent to the DCLTR Softkey.

• No declutter: All map features are visible

• Declutter – 1: Declutters land data

• Declutter – 2: Declutters land and SUA data

• Declutter – 3: Removes everything except the active flight plan

TRAFFIC – Press to display traffic on the inset map.

TOPO – Press to display topographical data (i.e., coastlines, terrain, rivers, lakes) and elevation scale on the inset map.

TERRAIN – Press to display terrain information on the inset map.

STRMSCP (optional) – Press to display the

Stormscope lightning data on the inset map

(within a 200 nm radius of the aircraft).

NEXRAD (optional) – Press to display NEXRAD precipitation data on the inset map.

XM LTNG (optional) – Press to display the XM Radio lightning data on the inset map.

BACK – Press to return to the previous level softkey configuration.

ALERTS – Press to display the Alerts window.

PFD – Press to display the additional softkeys for additional configuration of the PFD.

METRIC – Press to display the current and reference altitudes in meters, in addition to feet. Pressing the METRIC Softkey also changes the barometric setting to hectopascals.

DFLTS – Press to reset default settings on the PFD.

DME (optional) – Press to display the DME information window.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

BRG1 (bearing) – Press to cycle through the following information:

NAV1 – Displays NAV1 waypoint frequency or identifier and DME information in the BRG1 information window.

GPS – Displays GPS waypoint identifier and GPS distance information in the BRG1 information window.

OFF – Removes the BRG1 information window.

BRG2 (bearing) – Press to cycle through the following information:

SECTION 1

SYSTEM OVERVIEW

NAV2 – Displays NAV2 waypoint frequency or identifier and DME information in the BRG2 information window.

GPS – Displays GPS waypoint identifier and GPS distance information in the BRG2 information window.

OFF – Removes the BRG2 information window.

STD BARO – Press to set the barometric pressure to

29.92 inches of mercury (1013 hPa by pressing the METRIC Softkey).

BACK – Press to return to the previous level softkeys.

ALERTS – Press to display the Alerts window.

Figure 1-3 PFD Softkey Flow Chart – 1

Figure 1-4 PFD Softkey Flow Chart – 2

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

1-5

SECTION 1

SYSTEM OVERVIEW

OBS – Press to select OBS mode on the CDI when navigating by GPS (only available with active leg).

CDI – Press to change navigation mode on the CDI between GPS, VOR1, and VOR2.

DME (optional) – Press to display the DME Tuning window.

XPDR – Press to display the transponder mode selection softkeys.

STBY – Press to select standby mode.

ON – Press to select mode A.

ALT – Press to select altitude reporting mode.

VFR – Press to automatically squawk 1200 (only in the U.S.A., refer to ICAO standards for VFR codes in other countries).

CODE – Press to display transponder code selection softkeys 0-7.

0 through 7 – Press numbers to enter code.

IDENT – Press to provide special aircraft position identification to Air Traffic Control

(ATC).

BKSP – Press to remove numbers entered one at a time.

BACK – Press to return to the previous level softkeys.

IDENT – Press to provide special aircraft position identification to Air Traffic Control (ATC).

BACK – Press to return to the previous level softkeys.

IDENT – Press to provide special aircraft position identification to Air Traffic Control (ATC).

TMR/REF – Press to display the Timer/References window.

NRST – Press to display the Nearest Airports window.

ALERTS – Press to display the Alerts window.

1-6

Figure 1-5 PFD Softkey Flow Chart – 3

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 1

SYSTEM OVERVIEW

1.3 MFD SOFTKEYS

ENGINE – Pressing this softkey makes available the LEAN and SYSTEM Softkeys which in turn access the Lean

Page and the System Page, respectively.

MAP – Pressing this softkey enables the following softkeys:

TRAFFIC – Pressing this softkey displays/removes

Traffic on the Navigation Map.

TOPO – Pressing this softkey displays or removes topographic information on the Navigation Map.

TERRAIN – Pressing this softkey displays/removes terrain and obstacle data on the Navigation Map.

STRMSCP (optional) – Pressing this softkey displays/ removes Stormscope lightning data on the Navigation

Map.

NEXRAD (optional) – Pressing this softkey displays/ removes precipitation data on the Navigation Map.

XM LTNG (optional) – Pressing this softkey displays/ removes XM Radio lightning data on the Navigation

Map.

BACK – Pressing this softkey displays the ENGINE and

MAP top level softkeys.

DCLTR (declutter) – Pressing this softkey removes map information in three levels.

Figure 1-6 MFD Softkeys

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

1-7

1-8

SECTION 1

SYSTEM OVERVIEW

1.4 MFD PAGE GROUPS

1) Turn the large FMS Knob until the desired page group is selected.

2) Turn the small FMS Knob to select pages within the group. See Figure 1-7.

Nearest Group

Auxiliary Page Group

Waypoint Page Group

Map Page Group

Number of Pages in Current

Group

Figure 1-7 Page Group Icon

1.5 BACKLIGHTING

Manually adjust the backlight for the PFD and MFD:

1) Press the MENU Key on the PFD to display the

PFD Setup Menu window.

2) Press the small FMS Knob to activate the cursor.

‘PFD DSPL > AUTO’ is now highlighted.

3) Turn the small FMS Knob to display the selection window.

4) Turn the FMS Knob to select ‘MANUAL’, then press the ENT Key.

5) With the intensity value now highlighted, turn the small FMS Knob to select the desired backlighting.

6) Turn the large FMS Knob to highlight ‘MFD

DSPL > AUTO’ and repeat steps 3 through 5.

Selected Page

Figure 1-8 PFD Setup Menu Window

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 1

SYSTEM OVERVIEW

1.6 DATABASE UPDATES

Aviation Database Update

NOTE: The display downloads the aviation database and stores it internally. The aviation database SD card is not required to remain in the display after the update.

1) With the G1000 System OFF, insert the aviation database update SD card into the top card slot of the PFD (Label of SD card facing left).

2) Turn the G1000 System ON. This prompt is displayed on the upper left corner of the

PFD:

7) Verify that the correct update cycle is loaded during startup of the MFD.

Terrain and Obstacle Database Updates

NOTE: The data contained in the terrain and obstacle databases comes from government agencies. Garmin accurately processes and cross-validates the data, but cannot guarantee the accuracy and completeness of the data.

NOTE: Obstacles 200’ and higher are included in the obstacle database. It is very important to note that not all obstacles are necessarily charted and therefore may not be contained in the obstacle database.

Figure 1-9 Database Update Prompt

3) Press the ENT Key to confirm the database updated. This prompt is displayed:

These databases are not stored internally in the MFD or PFD. Supplemental Data Cards containing identical database versions must be kept in both displays to retain terrain and obstacle data. A Supplemental Data Card should be inserted into the bottom card slot of the PFD and MFD.

NOTE:

If the Supplemental Data Card is removed from the display, the TOPO and TER-

RAIN softkeys are not functional and are grayed out on the MFD Map Page.

Figure 1-10 Database Update Confirmation

4) After the update completes, the PFD starts in normal mode. Remove the aviation database update SD card from the PFD.

5) Turn the G1000 System OFF.

6) Repeat steps 1 through 4 for the MFD. The

MFD and PFD aviation databases are now updated.

1) Insert one card in the bottom card slot of the

MFD and one in the bottom card slot of the

PFD.

2) Apply power to the G1000 System. View the

MFD power-up splash screen. Check that the

Terrain and Obstacle databases are initialized and displayed on the scrolling window of the splash screen.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

1-9

SECTION 1

SYSTEM OVERVIEW

3) Acknowledge the Power-up Page agreement by pressing the ENT Key or the right most softkey.

4) At the MAP – NAVIGATION MAP page, select the MAP Softkey and check to make sure that the TOPO and TERRAIN softkeys are functional

(not grayed out).

5) Power down the G1000.

Figure 1-11 Power-Up Splash Screen Window

1-10

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 2

FLIGHT INSTRUMENTS

SECTION 2: FLIGHT INSTRUMENTS

The following discussions pertain to the Primary Flight

Display, unless otherwise indicated.

1 17 16 15 14

2

3

4

5

6

3

5

4

6

1

2

8

7

NAV Frequency Window

Airspeed Indicator

True Airspeed Box

Heading Box

Horizontal Situation Indicator

Outside Air Temperature Box

System Time Box

Transponder Status Bar

9

10

11

12

13

14

15

16

17

Turn Rate Indicator

Barometric Setting Box

Vertical Speed Indicator

Altimeter

Altitude Reference Box

COM Frequency Window

Navigation Status Window

Slip/Skid Indicator

Attitude Indicator

Figure 2-1 Default PFD Information

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

13

12

11

10

9

8

7

2-1

2-2

SECTION 2

FLIGHT INSTRUMENTS

11

1

10

2

3

1

2

3

4

5

6

4 5 6

Traffic Annunciation 7 Alerts Window

Selected Heading Box 8 Selected Course Box

Inset Map 9 Annunciation Window

BRG1 Information Window 10 Vertical Deviation/Glideslope Indicator

DME Information Window 11 Marker Beacon Annunciation

BRG2 Information Window

Figure 2-2 Additional PFD Information

Distance to Next Waypoint

Next Waypoint

Desired Track to

Next Waypoint

Current Track

Figure 2-3 PFD Navigation Status Window

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

9

8

7

SECTION 2

FLIGHT INSTRUMENTS

2.1 AIRSPEED INDICATOR

Actual Airspeed

Airspeed Trend

Vector

Speed Range

(flap speed range)

True Airspeed

Box

Vspeed

References

(best glide)

Figure 2-4 Airspeed Indicator

Speed Indication

The indicated airspeed is displayed inside the black pointer. The pointer will become red upon reaching

Vne.

Vspeed References

Vspeed References are turned on or off in the

Timer/References window. Press the TMR/REF Softkey to display the widow. When active (ON), the Vspeeds are displayed at their respective locations to the right of the airspeed scale. To activate the Vspeed References, display the Timer/Reference window and turn the large

FMS Knob to place the cursor in the ON/OFF field. Turn the small FMS Knob to select ON or OFF.

2.2 ATTITUDE INDICATOR

The Slip/Skid Indicator is located under the roll pointer and moves laterally away from the pointer to indicate lateral acceleration. One Slip/Skid indicator displacement is equal to one ball displacement when compared to a traditional slip/skid indicator.

10

2

1

Figure 2-5 Red Pointer at Vne

Speed Ranges

The color coded speed range strip denotes flaps operating range, normal operating range, and never exceed speed (Vne). A red range is also present for low speed awareness. Refer to the Pilot’s Operating Handbook

(POH) for airspeed limitations and indicator markings.

Airspeed Trend Vector

The end of the trend vector displays approximately what the airspeed will be in 6 seconds if the current rate of acceleration/deceleration is maintained.

3

4

5

3

4

5

1

2

Roll Pointer

Roll Scale

Horizon Line

Aircraft Symbol

Land Representation

6 Aircraft Wing Tips

7

8

Pitch Scale

Slip/Skid Indicator

9

10

Sky Representation

Roll Index Zero

Figure 2-6 Attitude Indicator

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

9

8

7

6

2-3

2-4

SECTION 2

FLIGHT INSTRUMENTS

2.3 ALTIMETER

Altitude Alerting

Within 1000 ft Within 200 ft Deviation of ±200 ft Altitude Reference

Box

Altitude Trend

Vector

Current Altitude

Altitude Select Bug

Figure 2-7 Altimeter

Barometric Setting

Box

Altitude Select Bug

The Altitude Select Bug is displayed at the selected altitude or, if the selected altitude is beyond the altitudes currently displayed, the bug is displayed at the top or bottom of the display (whichever is closest to the selected altitude).

Set the Selected Altitude Bug:

Turn the ALT Knobs to set the Altitude Select

Bug. The small ALT Knob sets the hundreds and the large ALT Knob sets the thousands. This altitude also appears in the Selected Altitude

Box above the Altimeter.

Altitude Trend Vector

The end of the trend vector displays approximately what the altitude will be in 6 seconds if the current rate of vertical speed is maintained.

Barometric Setting Box

To set barometric pressure, turn the BARO Knob to select the desired setting.

Figure 2-8 Altitude Alerting Visual Annunciations

Visual annunciations appear in the Selected Altitude

Box. Whenever the Selected Altitude is changed, the Altitude Alerter is reset. The Altitude Alerter is independent of the Automatic Flight Control System.

An aural tone is heard when the aircraft is within 200 feet of acquiring the selected altitude or when deviating beyond 200 feet of the acquired selected altitude.

Barometric Minimum Descent Altitude

The desired barometric minimum descent altitude

(MDA, or Decision Height, DH) can be set in the Timer/

References Window.

Visual annunciations alert the pilot when approaching the MDA:

• When the aircraft altitude descends to within 2500 feet of the MDA setting, the Barometric Minimum

Box appears with the altitude in light blue text.

The bug appears on the tape in light blue once in range.

• When the aircraft passes through 100 feet of the

MDA, the bug and text turn white.

• Once the aircraft descends past the MDA, the bug and text turn yellow and the aural alert, “Minimums

Minimums”, is generated.

Alerting is inhibited while the aircraft is on the ground.

If the aircraft climbs after having reached the MDA, once it reaches 50 feet above the MDA, alerting is disabled.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Within 2500 ft Within 100 ft

SECTION 2

FLIGHT INSTRUMENTS

2.5 MARKER BEACON ANNUNCIATIONS

Marker Beacon

Annunciation

Barometric Minimum Bug

Barometric

Minimum Box

Vertical

Deviation/Glideslope

Indicator

Altitude Reached

Figure 2-9 Barometric Minimum Descent Altitude

Alerting Visual Annunciations

2.4 VERTICAL DEVIATION/GLIDESLOPE

INDICATOR

The Vertical Deviation/Glideslope Indicator appears when an ILS is tuned in the active NAV field.

Figure 2-10 Marker Beacon and Vertical Deviation

2.6 VERTICAL SPEED INDICATOR

Selected Vertical Speed

Vertical Speed Bug

Vertical Speed Pointer

Figure 2-11 Vertical Speed Indicator

The actual vertical speed is displayed inside the pointer.

When the Flight Director is placed in Vertical Speed

Mode (by pressing the VS Key) the Vertical Speed Bug is displayed. Press the NOSE UP or NOSE DN Key to adjust.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

2-5

2-6

SECTION 2

FLIGHT INSTRUMENTS

1

2

3

4

5

6

2.7 HORIZONTAL SITUATION INDICATOR

(HSI)

14 13

8

7

12

11

10

9

Turn Rate Indicator and Heading Trend Vector

Tick marks to the left and right of the lubber line denote half-standard and standard turn rates. A magenta turn rate trend vector shows the current turn rate. The end of the trend vector gives the heading predicted in six seconds, based on the present turn rate. At rates greater than 4 deg/sec, an arrowhead appears at the end of the magenta trend vector and the prediction is no longer valid.

Half-Standard Turn

Rate Tick Mark

Standard Turn

Rate Tick Mark

Turn Rate

Trend Vector

(rate > 4 deg/sec)

Figure 2-13 Turn Rate Indicator and Trend Vector

7

8

4

5

6

9

10

1

2

3

13

14

11

12

Turn Rate Indicator

Lateral Deviation Scale

Navigation Source

Aircraft Symbol

Course Deviation Indicator

Rotating Compass Rose

OBS Mode

TO/FROM Indicator

Heading Bug

Course Pointer

Flight Phase

Turn Rate and Heading Trend Vector

Heading

Lubber Line

Turn Rate

Trend Vector

(standard rate)

Figure 2-14 Standard-Rate Turn Indication

Course Pointer

The course pointer is a single line arrow (GPS, VOR1 and LOC1) or double line arrow (VOR2 and LOC2) which points in the direction of the set course.

Figure 2-12 Horizontal Situation Indicator

Figure 2-15 Course Pointer

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 2

FLIGHT INSTRUMENTS

Course Deviation Indicator (CDI)

The CDI scale automatically adjusts to the current phase of flight (enroute 5.0 nm, terminal area 1.0 nm, or approach 0.3 nm). Scaling may be selected manually from the MFD System Setup Page. See System Setup in the G1000 Pilot’s Guide for more details.

Bearing Pointers and Information Windows

Pressing the PFD Softkey provides access to the BRG1 and BRG2 Softkeys. The BRG1 pointer is a single line pointer. The BRG2 pointer is a double line pointer.

DME

Information

Window

Bearing 1

Pointer

Bearing 2

Pointer CDI

Waypoint

Identifier

Distance to

Bearing Source

Bearing

Source

Pointer

Icon

Figure 2-17 BRG1 Information Window

Distance to

Bearing Source

Waypoint

Identifier

Pointer

Icon

Bearing

Source

Figure 2-18 BRG2 Information Window

DME (optional)

To display the DME Information Window, press the

PFD Softkey followed by the DME Softkey.

Bearing 1

Information

Window

Bearing 2

Information

Window

Figure 2-16 HSI with Bearing Information

Figure 2-19 DME Information Window

Navigation Source

Change navigation sources:

1) Press the CDI Softkey to change from GPS to

VOR1/LOC1.

2) Press the CDI Softkey again to change from

VOR1/LOC1 to VOR2/LOC2.

3) Press the CDI Softkey a third time to return to

GPS.

When using GPS as the navigation source, the following may appear:

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

2-7

SECTION 2

FLIGHT INSTRUMENTS

• INTEG – GPS information is either not present or is invalid for navigation use

• WARN – GPS detects a position error

• SUSP – Displayed when in OBS Mode indicating

GPS waypoint sequencing is suspended.

2-8

Figure 2-20 GPS INTEG, GPS SUSP, LOC1 and VOR2

Enable/disable OBS mode while navigating with GPS:

1) Press the OBS Softkey to select OBS Mode.

2) Turn the CRS Knob to select the desired course

TO/FROM the waypoint.

3) Press the OBS Softkey again to return to normal operation.

NOTE: The OBS Softkey is only displayed when navigating an active leg using GPS.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 3 – ENGINE

INDICATION SYSTEM (EIS)

SECTION 3: ENGINE INDICATION

SYSTEM (EIS)

3.2 LEAN ENGINE DISPLAY

3.1 ENGINE DISPLAY

In all cases green indicates normal operation, yellow indicates caution, and red indicates warning.

Pressing the ENGINE Softkey makes available the

LEAN and SYSTEM Softkeys which in turn provide access to the Lean Page and the System Page, respectively.

Manifold

Pressure

Gauge

RPM Gauge

Fuel Flow

Indicator

Oil Temperature

Indicator

Ammeter

Fuel Flow

Numeric

Readout

Leaning

Pointer

Cylinder Head

Temperature

Indicator

Oil Pressure

Indicator

Cylinder peak temperature

Exhaust Gas

Temperature

Bar Graph

Fuel Flow

Numeric

Readout

Difference between peak and current temperature of selected cylinder

EGT Readout

For Selected

Cylinder

Cylinder Head

Temperature

Bar Graph CHT Readout

For Selected

Cylinder

Figure 3-2 LEAN Engine Page

Press the CYL SLCT Softkey to select the desired cylinder for monitoring.

The CYL SLCT Softkey becomes disabled when the

ASSIST Softkey is pressed.

Pressing the ASSIST Softkey causes the first cylinder that peaks to become highlighted and information for that cylinder to be displayed.

Voltmeter

Fuel Quantity

Indicator

Figure 3-1 Default Engine Page

In a maximum power climb or cruise climb, engine leaning may be done using the Leaning Pointer as a reference when adjusting fuel mixture

NOTE: The pilot should follow the engine manufacturer’s recommended leaning procedures in the Pilot’s Operating Handbook (POH).

Any exceedance of default Engine Page parameters, while viewing the Lean Engine Page, will cause the display to automatically switch back to the default Engine Page.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

3-1

SECTION 3 – ENGINE

INDICATION SYSTEM (EIS)

3.3 ENGINE SYSTEM DISPLAY

If desired, use the DEC FUEL, INC FUEL and RST

FUEL Softkeys to adjust the amount of fuel remaining for totalizer calculations.

NOTE: Fuel calculations do not use the aircraft fuel quantity indicators, and are calculated from the last time the fuel was reset.

System

Information

Fuel Calculation

Information

Electrical

Information

3-2

Figure 3-3 SYSTEM Engine Page

Any exceedance of default Engine Page parameters, while viewing the System Engine Page, will cause the display to automatically switch back to the default Engine

Page.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 4 – NAV/COM &

TRANSPONDER

SECTION 4: NAV/COM AND

TRANSPONDER

The Nav/Com controls and frequency windows are located on the Primary Flight Display and the Multi-

Function Display in the same locations.

NAV

Controls NAV Frequency Window COM Frequency Window

COM

Controls

Figure 4-1 G1000 VHF NAV/COM Interface (PFD)

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

4-1

4-2

SECTION 4 – NAV/COM &

TRANSPONDER

Standby NAV

Frequency Field

Selected NAV

Frequency

Selected COM

Frequency

Standby COM

Frequency Field

Figure 4-2 Frequency Fields

Tuning Box Active NAV

Frequency Field

Active COM

Frequency Field

Tuning Box

Frequency Transfer Arrow Tuning Box

Figure 4-3 Frequency Transfer Arrow and Tuning Box

NAV Controls

VOL/PUSH

ID Knob

VOL/PUSH

SQ Knob

Frequency Transfer Key

Dual NAV

Knob

Dual COM

Knob

• Turn to tune in desired frequencies.

• Press to change tuning box positions.

Figure 4-4 NAV/COM Controls

COM Controls

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 4 – NAV/COM &

TRANSPONDER

4.1 RADIO STATUS INDICATIONS

• RX – When a COM signal is received, a white ‘RX’ appears by the active COM frequency during signal reception.

• TX – When a COM radio is transmitting, a white ‘TX’ indication appears to the right of the corresponding

COM frequency.

• ID – When the Morse code identifier is ON for a NAV radio, a white ‘ID’ indication appears to the left of the corresponding active NAV frequency. The Morse code identifier can be heard if the corresponding

NAV radio is selected on the audio panel.

4.4 QUICKLY ACTIVATING 121.500 MHZ

Pressing and holding the COM Frequency Transfer

Key for approximately two (2) seconds automatically tunes the selected COM radio to the emergency frequency.

4.5 OPTIONAL NAV RADIOS

DME Radio (optional)

The Tuning window is displayed by pressing the DME

Softkey.

Figure 4-5 Radio Status Indications

4.2 VOLUME

‘VOLUME’ is displayed in place of the associated radio name (i.e., ‘COM1’ or ‘NAV2’) for two seconds after the volume level is last changed. The percentage of maximum volume is displayed in place of the standby frequency selected by the tuning box.

Figure 4-7 Radio Tuning Window

Change the DME tuning source:

1) From the Tuning window, turn the large FMS

Knob to highlight the DME source field.

2) Turn the small FMS Knob to display the selection window. Turn the FMS Knob to select the desired mode and press the ENT Key.

Figure 4-6 COM Volume Level

4.3 AUTOMATIC SQUELCH

Automatic squelch can be disabled for a COM radio by pressing the COM Knob to place the tuning box on the desired COM’s standby frequency, then by pressing the

VOL/PUSH SQ Knob.

Figure 4-8 DME Selection Window

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

4-3

SECTION 4 – NAV/COM &

TRANSPONDER

4.6 FREQUENCY AUTO-TUNING

Auto-tuning on the PFD

4.7 TRANSPONDER

Mode Selection

The STBY, ON and ALT Softkeys can be accessed by pressing the XPDR Softkey.

Ground Mode (Automatic)

GND is displayed when the aircraft is on the ground.

4-4

Figure 4-9 Nearest Airports Window (PFD)

1) Press the NRST Softkey to display the Nearest

Airports Window.

2) Turn either FMS Knob to highlight the desired frequency.

3) Press the ENT Key to place the frequency in the standby field of the active COM.

4) Press the Frequency Transfer Key to place the frequency in the active field.

NAV frequencies are entered automatically in the NAV window upon approach loading or approach activation.

Auto-tuning on the MFD

Auto-tuning on the MFD is done in much the same way as on the PFD. Use the FMS Knobs to select the desired frequency on any of the information pages. Pressing the

ENT Key then loads the selected frequency in the tuning box as a standby frequency.

Figure 4-10 Ground Mode

Reply Status

When the transponder sends replies to interrogations, an “R” indication appears momentarily in the reply status field.

Figure 4-11 Reply Indication

Code Selection

1) Press the XPDR Softkey to display the transponder Mode Selection softkeys.

2) Press the CODE Softkey to display the transponder Code Selection softkeys, which includes the digit softkeys.

3) Press the appropriate digit softkeys to enter the code in the four-digit code field of the

Transponder Status bar. Five seconds after the fourth digit has been entered, the transponder code becomes activated.

When entering a code, press the BKSP Softkey as needed to back up and change code digits.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Following is a list of important codes:

• 1200 – VFR code in the U.S. (please refer to the

ICAO standards for VFR codes in other countries).

• 7000 – VFR code commonly used in Europe (please refer to the ICAO standards).

• 7500 – Hijack code.

• 7600 – Loss of communication code.

• 7700 – Emergency code.

• 7777 – Military interceptor operations code

(NEVER ENTER THIS CODE).

• 0000 – Code for military use (in the U.S.).

Flight ID Reporting

If so configured, the Flight ID may be entered in the

Timer/Reference window.

Figure 4-12 Timer/References Window

Flight ID

SECTION 4 – NAV/COM &

TRANSPONDER

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

4-5

SECTION 4 – NAV/COM &

TRANSPONDER

Blank Page

4-6

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 5 – AUDIO PANEL

SECTION 5: AUDIO PANEL

Transmitters

(COM3 MIC is unavailable)

Split COM

(Not recommended for use in the Beechcraft A36/G36)

Passenger Address

Marker Beacon/Mute

Transceiver Audio

(COM 3 is unavailable)

Telephone (Unavailable)

Speaker

Marker Beacon Signal Sensitivity

Aircraft Navigation Radio Audio

Aircraft Navigation Radio Audio

(DME optional, ADF & AUX unavailable)

Manual Squelch Recorded COM Audio Playback

ICS Isolation

VOL/SQ

Volume/Squelch

VOL Annunciation SQ Annunciation

Reversionary Mode

Figure 5-1 Audio Panel Controls

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

5-1

SECTION 5 – AUDIO PANEL

5.1 COM RADIO SELECTION

Pressing the COM1 MIC or COM2 MIC Key selects the active transmitter (i.e., microphone). The associated receiver audio (COM1 or COM2) also becomes selected when the COM MIC Key is pressed.

To prevent deselecting the desired received audio when pressing another COM MIC Key, press the already selected COM1 or COM2 Key before pressing the other

COM MIC Key.

Inner Marker

Annunciator

Outer Marker

Annunciator

Middle Marker

Annunciator

5-2

Figure 5-3 Marker Beacon Annunciators on the PFD

Figure 5-2 Transceivers

5.2 MARKER BEACON RECEIVER

The marker beacon receiver is always on. Only the marker beacon audio can be turned off. Figure 5-3 shows the marker beacon annunciators on the PFD.

When the MKR/MUTE Key is pressed, the key annunciator is lit and the audio tone can be heard over the speaker or headsets during marker beacon reception.

When the tone is active, pressing the MKR/MUTE

Key once mutes the audio but does not affect the marker annunciator. The audio returns when the next marker signal is received.

To turn off the marker beacon audio, press the MKR/

MUTE Key once when there is no marker indication present, or press twice when an indication is present. The key annunciator will be extinguished when the marker beacon audio is turned off.

Marker Beacon Signal Sensitivity

The HI SENS Key can be pressed for increased marker beacon signal sensitivity.

Figure 5-4 Marker Beacon

5.3 NAV RADIO AUDIO SELECTION

Pressing DME, NAV1, or NAV2 selects and deselects the radio source and activates the annunciator. Selected audio can be heard over the headset and the speakers.

These three keys can be selected individually or together.

Figure 5-5 Navigation Radios

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 5 – AUDIO PANEL

5.4 INTERCOM SYSTEM (ICS) ISOLATION

Press the PILOT and/or COPLT Key to select who is isolated from hearing the Nav/Com radios and music.

Selection scenarios are addressed in Table 5-1.

5.5 INTERCOM SQUELCH CONTROL

Select manual squelch for intercom audio by pressing the MAN SQ Key to light the annunciator.

Pressing the small VOL/SQ Knob now switches between volume and squelch adjustment by lighting VOL or SQ respectively.

Figure 5-6 ICS Isolation

Mode

ALL

PILOT

COPILOT

PILOT KEY

ANNUNCIATOR

OFF

ON

OFF

COPLT KEY

ANNUNCIATOR

OFF

OFF

ON

Pilot Hears

Selected radios; pilot; copilot; passengers;

MUSIC 1

Selected radios; pilot

Figure 5-7 Volume/Squelch Control

Copilot Hears

Selected radios; pilot; copilot; passengers;

MUSIC 1

Copilot; passengers;

MUSIC 1

Passenger

Hears

Selected radios; pilot; copilot; passengers;

MUSIC 2

Copilot; passengers;

MUSIC 2

Selected radios; pilot; passengers;

MUSIC 1

Copilot

Selected radios; pilot; passengers;

MUSIC 2

CREW ON ON

Selected radios; pilot; copilot

Selected radios; pilot; copilot

Passengers;

MUSIC 2

Table 5-1 ICS Isolation Modes

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

5-3

SECTION 5 – AUDIO PANEL

5.6 DIGITAL CLEARANCE RECORDER

AND PLAYBACK

Each reception of primary active COM audio is automatically recorded in a memory block. When the next transmission is received, it is recorded in the next memory block, and so on. Once the 2.5 minutes of recording time has been reached, the recorder begins recording over the stored memory blocks, starting from the oldest block.

Powering off the unit automatically clears all recorded blocks.

Figure 5-8 Playback

• Pressing PLAY once plays the latest recorded memory block, then returns to normal operation.

• Pressing MKR/MUTE while playing a memory block stops play.

• Pressing the PLAY Key during play begins playing the previously recorded memory block. Each subsequent press of the PLAY Key will begin playing the next previously recorded block.

If a COM input signal is detected during playback, playback is halted and the new COM input signal is recorded as the latest block.

5-4

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

SECTION 6: AUTOMATIC FLIGHT

CONTROL

In addition to the AFCS (Automatic Flight Control

System) keys on the MFD, as discussed in the System

Overview section, the following buttons and switches used by the AFCS are located in the cockpit separately from the PFD and MFD.

• AP DISC (Autopilot Disconnect) Button —

Located on the pilot’s control wheel, pressing this button disengages the autopilot. Pressing it also acknowledges an autopilot disconnect.

• CWS (Control Wheel Steering) Button —

Located on the pilot’s control wheel, pressing and holding the CWS button disengages the control surface servos without disengaging the autopilot. If the flight director has not been activated, pressing the CWS button will activate the flight director in the default pitch and roll hold modes.

• GA (Go Around) Button — Located on the subpanel or throttle lever, the GA button disengages the autopilot and selects the Go Around Pitch and

Roll (wings level) modes.

Figure 6-1 AFCS Keys

Pressing the FD Key activates only the flight director in the default Pitch Hold/Roll modes without engaging the autopilot. Pressing the AP Key activates the flight director and yaw damper, and engages the autopilot. When only the flight director is engaged, pressing the FD Key disengages the flight director.

Upon activation of the autopilot and/or flight director, command bars are displayed on the PFD. If the attitude information being sent to the flight director becomes invalid or unavailable, the command bars are removed from the display.

• MET (Manual Electric Trim) Switch — This switch is used to operate manual electric pitch trim.

Moving both switches forward simultaneously trims the aircraft nose down. Moving both switches aft simultaneously trims the aircraft nose up. The left switch is the ARM contact and the right switch controls the up/down trim. Pressing the ARM switch disengages the autopilot, if currently engaged. If one side of the switch is active for more than three seconds without the other side also being active,

‘PTRM’ is displayed in the AFCS System Status field on the PFD. Pressing the MET ARM switch also acknowledges an autopilot disconnect.

Figure 6-2 Command Bars

6.1 MODE ANNUNCIATIONS

Mode annunciations are displayed on the PFD. Figure

6-3 shows the AFCS Status Bar fields. Modes associated with aircraft movement about the roll axis are displayed on the left side. Modes associated with aircraft movement about the pitch axis are displayed on the right. Armed modes are displayed in white and active modes are displayed in green.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-1

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Armed Mode

Active Mode Yaw Damper Status

Autopilot Status

Mode Reference

Active Mode Armed Mode

Roll Axis Modes

System Status Field

(see Annunciations & Alerts)

Aircraft Attitude

Symbol

Flight Director

Command Bars

AFCS Status Bar

Pitch Axis Modes

Selected Altitude

Box

6-2

6.2 OVERSPEED PROTECTION

Figure 6-3 PFD AFCS Display

6.3 AP ENGAGEMENT/DISENGAGEMENT

An overspeed annunciation (flashing inverse video) is displayed above the airspeed tape.

Figure 6-4 Overspeed Annunciation

When an overspeed caution occurs, reduce engine power and/or adjust the pitch reference to slow the aircraft.

When the AP Key is pressed, the system engages the autopilot. If the flight director is not already active, it is also engaged when the AP Key is pressed. If the yaw damper is not already active, it too is engaged when the

AP Key pressed.

Autopilot engagement is displayed in the Autopilot

Status field of the AFCS Status Bar. Autopilot engagement is indicated by a green ‘AP’.

Autopilot Engaged

Figure 6-5 Autopilot Engaged Annunciation

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Automatic Disengagement

Automatic disengagement typically occurs due to a failure. Automatic disengagement is annunciated by a flashing ‘AP’, alternating red on white and white on red in the Autopilot Status field. Also, the autopilot disconnect aural alert will be heard. Both the annunciation and the aural alert will continue until acknowledged by pressing the AP DISC button or the MET ARM switch. The Yaw

Damper may or may not disengage, depending on the cause of the automatic AP disengagement.

Automatic Disconnect

Yaw Damper

When the autopilot is engaged, the Yaw Damper is automatically engaged. When the Yaw Damper is active, the ‘YD’ annunciation appears in the Yaw Damper Status field as shown:

Yaw Damper is active.

Figure 6-9 Yaw Damper Active

To disengage the Yaw Damper, press the YD Key. The

‘YD’ annunciation turns yellow and flashes for five seconds upon disengagement:

Yaw Damper is disengaging.

Figure 6-6 Automatic Disconnect Annunciation

Manual Disengagement

The autopilot may also be manually disengaged by pressing the AP DISC button, the GA button, the

MET ARM switch, or by pressing the AP Key on the MFD.

Manual disengagement is annunciated by a five-second flashing yellow ‘AP’ in the Autopilot Status field and by a two-second Autopilot disconnect aural alert. The Yaw

Damper will also disengage with the autopilot.

Manual Disconnect

Figure 6-7 Manual Disconnect Annunciation

Control Wheel Steering

Pressing and holding the CWS button disengages the servos from the flight control surfaces and allows manual manuevering of the aircraft. At the same time, the flight director is synchronized to the aircraft attitude during the maneuver. The ‘AP’ annunciation is temporarily replaced by ‘CWS’ in white until the CWS button is released.

Control Wheel Steering

Figure 6-8 CWS Annunciation

Figure 6-10 Yaw Damper Disengagement

6.4 LOSS OF DATA

In general, a flashing yellow mode annunciation indicates either the loss of sensor data (AHRS, ADC, or GIA) or loss of navigation data (VOR, LOC, or GPS) required to compute commands.

When such a loss occurs, the system automatically reverts to the default mode for the affected axis (wings level ROL for roll axis, PIT for pitch axis). The flashing annunciation stops when the pilot presses the affected mode button or selects another mode for the axis. If no pilot action is taken, the flashing annunciation stops after ten seconds.

Figure 6-11 Loss of VOR Signal

6.5 PITCH AXIS MODES

Mode annunciations for active pitch axis modes are shown in green during normal operation. Note the Go-

Around button is not located on the MFD.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-3

6-4

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

AFCS Key AFCS Mode

FD/AP only Pitch Hold (Default)

ALT

VS

Altitude Hold

Vertical Speed

FLC

APR

GA

Flight Level Change

Glideslope (vertical component of Approach)

Go Around

Annunciation

PIT

ALT nnnnn

VS nnnn

FLC nnn

GS

KT

FT

FPM

GA

The default pitch axis mode is Pitch Hold (PIT). When no other pitch axis modes are selected, this is the active pitch axis mode when the autopilot and/or flight director is engaged.

Pitch Hold Mode (PIT)

1) Press the AP or FD Key. ‘PIT’ will be displayed in green in the Active Mode field of the AFCS

Status Bar. The system will maintain or give command bar direction for a constant pitch attitude (pitch reference) depending on which key is pressed.

Pitch Hold mode is active

2) Altitude Hold mode is automatically armed with

‘ALT’ displayed white in the Armed Mode field to the right of the ‘PIT’ annunciation.

3) Pitch attitude can be adjusted in 0.5 degree increments by pressing the NOSE UP/NOSE DN

Keys.

4) Aircraft pitch may also be changed by pressing and holding the CWS button to manually establish the desired pitch using the control wheel. When the CWS button is released, the current pitch angle will be maintained.

5) If desired, enter an altitude in the Selected

Altitude Box by turning the ALT Knob. As the selected altitude is reached ‘ALT’ will flash in green for 10 seconds in the Acitve Mode field, after which the annunciation stops flashing.

This signals the altitude capture is complete and the selected altitude will be maintained.

If only the flight director is engaged, pitch commands are given to manually maintain the selected altitude.

Altitude Hold mode is armed

Flight Director command bars maintain desired pitch reference

Figure 6-12 Pitch Hold Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Altitude Hold Mode (ALT)

1) Press the ALT Key. The flight director is activated

(if not already active) and ‘ALT’ is now displayed in green in the Active Mode field with the current altitude displayed in the Altitude

Reference field.

2) Pitch commands will be given to manually maintain the current altitude. Press the AP

Key to engage the autopilot for maintaining the current altitude.

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

3) To change aircraft altitude, press and hold the CWS button and manually maneuver to the desired altitude. Upon reaching the desired altitude, release the CWS button. This new altitude is now displayed in the Altitude

Reference field. The autopilot will now hold the aircraft at this altitude.

NOTE: If the Selected Altitude is captured during

CWS maneuvering, the Flight Director altitude reference is not changed. To adjust the altitude reference in this case, the pilot must again press the CWS button after the Selected Altitude is captured.

Altitude Hold mode is active Altitude Reference

Flight Director command bars hold pitch attitude to maintain the altitude reference

Figure 6-13 Altitude Hold Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-5

6-6

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Vertical Speed Mode (VS)

1) Press the VS Key. The flight director is now activated (if not already active) and ‘VS’ is displayed in green in the Active Mode field and the Vertical Speed Bug will appear on the

Vertical Speed Indicator. Pitch commands are given to manually maintain vertical speed.

Press the AP Key to engage the autopilot for maintaining the current vertical speed.

Altitude Hold mode is automatically armed with

‘ALT’ displayed white in the Armed Mode field to the right of the ‘VS’ annunciation.

2) The Vertical Speed Bug can be adjusted in 100 fpm increments by pressing the NOSE UP/NOSE

DN Keys to set the desired vertical speed. The vertical speed setting will be displayed in the

Selected Vertical Speed box and in the Vertical

Speed Reference field in the AFCS Status Bar.

Vertical Speed mode is active

The Vertical Speed box is located above the VSI when the aircraft is climbing and below the VSI when descending.

3) Vertical speed may also be changed by pressing and holding the CWS button to manually establish the desired vertical speed using the control wheel. When the CWS button is released, the current vertical speed will be maintained.

4) A desired altitude may be entered in the

Selected Altitude Box by turning the ALT

Knob. With Altitude Hold mode armed, as the selected altitude is reached ‘ALT’ will flash in green for 10 seconds in the Acitve Mode field, after which the annunciation stops flashing.

This signals the altitude capture is complete and the selected altitude will be maintained.

If only the flight director is engaged, pitch and roll commands are given to manually maintain the selected altitude.

Vertical Speed Reference

Altitude Hold is Armed

Selected Altitude

Selected Vertical

Speed

Flight Director command bars indicating a climb at the prescribed vertical speed, to the Selected

Altitude

Vertical Speed

Reference Bug

Figure 6-12 Vertical Speed Hold Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Flight Level Change Mode (FLC)

1) Select the desired altitude by turning the

ALT Knob to set the altitude in the Altitude

Select box. This altitude must be selected first because Flight Level Change mode will only fly

toward a selected altitude.

2) Press the FLC Key. The flight director is activated (if not already active) and ‘FLC’ is now displayed in green in the Active Mode field and the Airspeed Bug will appear on the

Airspeed Indicator. Pitch commands are given to manually maintain airspeed. Press the AP

Key to engage the autopilot for maintaining the current airspeed.

Airspeed box above the Airspeed Indicator and in the Airspeed Reference field in the AFCS

Status Bar.

4) Airspeed may also be changed by pressing and holding the CWS button to manually establish the desired airspeed using the control wheel.

When the CWS button is released, the current airspeed will be maintained.

5) Adjust engine power to allow the autopilot to fly the aircraft at a pitch attitude which corresponds to the selected airspeed and the desired flight profile (descent or climb).

Altitude Hold mode is automatically armed with

‘ALT’ displayed white in the Armed Mode field to the right of the ‘FLC’ annunciation.

3) The Airspeed Bug can be adjusted in 1 knot increments by pressing the NOSE UP/NOSE DN

Keys to set the desired airspeed. The airspeed setting will be displayed in the Selected

Flight Level Change mode is active

6) With Altitude Hold mode armed, as the selected altitude is reached, ‘ALT’ will flash in green for 10 seconds in the Active Mode field, after which the annunciation stops flashing. This signals the altitude capture is complete and the selected altitude will be maintained at the selected airspeed. If only the flight director is engaged, pitch commands are given to manually maintain the selected altitude.

Airspeed Reference

Altitude Hold mode is armed

Selected Altitude

Selected Airspeed

Airspeed Reference

Bug

Figure 6-15 Flight Level Change Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-7

6-8

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Go-Around Mode (GA)

Pressing the GA button (not located on the MFD) engages the flight director in a wings level, 7 degree pitch up attitude. Go-Around mode disengages the autopilot, and arms Altitude Hold Mode automatically. Subsequent autopilot engagement is also allowed. If the pitch attitude is changed manually (e.g with CWS button or the NOSE

UP/NOSE DN Keys), Pitch and Roll Hold modes will automatically be selected.

Glideslope (GS)

NOTE: Pressing the CWS button while Glideslope

Mode is active does not cancel the mode. The autopilot guides the aircraft back to the glideslope upon release of the CWS button.

Glideslope Mode is only available when the flight director has been set for approach. Glideslope Mode is automatically armed under the following conditions:

• Valid localizer frequency is tuned

• Horizontal Situation Indicator (HSI) is in LOC mode, with valid deviation indication

• Valid glideslope deviation

• APR Key is pressed

Autopilot disconnect annunciation flashes yellow for 5 seconds

Go Around mode is active in both pitch axis

& roll axis modes

Flight Director command bars indicating climb

Figure 6-16 Go-Around Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

6.6 ROLL AXIS MODES

Mode annunciations for active roll axis modes are shown in green during normal operation.

If the aircraft bank angle is < 6 degrees when the key is pressed, the aircraft will be maintained at wings level. If only the flight director is active, command bars give guidance to maintain wings level.

Roll Hold mode is annunciated by ‘ROL’.

AFCS

Key

AFCS Mode

FD/AP only Roll Hold (Default)

HDG Heading Select

VOR Enroute

Arm / Capture / Track

NAV

APR

GA

GPS Arm / Capture / Track

BC Arm / Capture / Track

LOC Arm / Capture / Track;

(No Glideslope)

GPS Arm / Capture / Track

VOR Approach

Arm / Capture / Track

ILS Approach

Arm / Capture / Track

(Glideslope pitch mode automatically armed)

Go Around (Wings Level)

Annunciation

ROL

HDG

VOR

GPS

BC

LOC

GPS

VAPP

LOC

GA

Figure 6-17 Roll Hold Mode

2) A new heading can be established by pressing and holding the CWS button and manually turning the aircraft to the desired new heading.

Release the CWS button and the aircraft will maintain wings level at approximately the new heading, but will not hold the heading. The same practice applies to holding roll attitude.

The default roll axis mode is Roll Hold (ROL). When no other roll axis modes are selected, this is the active roll axis mode when the autopilot and/or flight director is engaged.

Roll Hold Mode (ROL)

1) Press the FD or AP Key.

If the aircraft bank angle is ≥ 6 degrees when the key is pressed, Roll Hold mode is selected by default. Roll attitude at the time of activation is maintained by the autopilot up to 22˚. If only the flight director is active, command bars indicate the proper roll attitude.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-9

6-10

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Heading Select Mode (HDG)

1) Turn the HDG Knob to move the heading bug on the HSI to the desired heading. When the knob is turned, the Selected Heading box will appear and remain for three seconds after the knob stops moving. The selected heading will be displayed in the Selected Heading box.

2) With the autopilot and/or flight director engaged, press the HDG Key. ‘HDG’ is now displayed in green in the Active Mode field. If the autopilot is engaged, the aircraft will begin to turn toward the selected heading. When the selected heading is reached, the aircraft will maintain this heading. If only the flight director is engaged, manually maneuver the aircraft to the command bars to aquire the selected heading.

3) The heading may be adjusted by turning the

HDG Knob and moving the heading bug to a new heading. The aircraft will turn in the same direction the heading bug is moved. However, if the heading bug is moved more than 340 degrees at a time, a turn reversal will be the result.

Heading Select mode Altitude Hold mode is active

Flight Director command bars tracking Selected

Heading

Selected Heading

Box

Selected Heading

Bug

Figure 6-18 Heading Select Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Navigation Mode (GPS, VOR, LOC, or BC)

Pressing the NAV Key activates the Navigation Mode.

The Navigation mode acquires and tracks the selected navigation receiver on the HSI (e.g. GPS, VOR or LOC).

GPS roll steering commands are followed when the HSI is in GPS mode, and creates roll steering commands from the Selected Course and deviation when the HSI is in

VOR, LOC, or BC (backcourse) modes.

Turning the CRS Knob moves the Course Pointer and displays the Selected Course box. The Selected Course is displayed in the box. The box is displayed while the knob is turning and disappears three seconds after the knob stops turning.

Backcourse mode is automatically selected when the localizer front course is greater than 105 degrees from the aircraft heading.

NOTE: When making a backcourse approach, set

Selected Course to the localizer front course.

Navigation Mode Armed

If the CDI is not centered (deviation >1 dot) when the

Navigation mode is selected, the mode is automatically armed. The armed annunciation appears in white to the left of the active roll axis mode.

See the Example Procedures Using AFCS section for more information.

Navigation Mode is active using GPS source

Flight Level Change mode is active

Altitude Hold is armed

Flight Director command bars indicating a left turn to track GPS course and a climb to intercept

Selected Altitude

Figure 6-19 Navigation Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Selected Course

GPS is active navigation receiver on the HSI.

6-11

6-12

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Approach Mode (GPS, VAPP or LOC)

The Approach mode acquires and tracks the selected navigation receiver on the HSI (GPS, VOR or LOC). This mode uses the selected navigation receiver deviation and desired course inputs to fly the approach. The Approach mode provides greater sensitivity for VOR tracking than

Navigation mode, and allows the autopilot to fly an ILS approach with a glideslope.

NOTE: While using Approach mode, the

Glideslope mode is automatically armed when

LOC mode is selected on the HSI.

If the CDI is not centered (deviation >1 dot) when the

Approach mode is selected, the mode is automatically armed. The armed annunciation appears in white to the left of the active roll axis mode.

See the Example Procedures Using AFCS section for more information.

Go Around (GA)

Go Around mode maintains a wings level, 7 degree nose up attitude for instances where the pilot wishes to execute a missed approach or go around. Figure 6-16 depicts the Go Around mode on the PFD.

Approach Mode is active Glideslope is active

Flight Director command bars indicating descent on localizer/ glideslope path

LOC2 is the active navigation receiver on the

HSI

Figure 6-20 Approach Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6.7 EXAMPLE PROCEDURES USING AFCS

This section provides a scenario-based set of procedures showing various autopilot modes used during a flight. In this scenario, the aircraft departs Reid-Hillview Airport

(KRHV) from runway 13L, enroute to Fresno Yosemite

International Airport (KFAT). Climb to an altitude of 7,000 feet MSL and fly a heading of 070 degrees to intercept airway V107. Fly airway V107 to Panoche

VORTAC (PXN) using VOR navigation, then fly airway

V230 using a GPS flight plan. Prior to reaching Clovis

VORTAC (CZQ), descend to 3,000 feet and load the ILS approach to R29R at KFAT. Fly the ILS approach and execute a missed approach.

KRHV

070

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

NOTE: The diagrams in the following examples are for instructional purposes only and may not be used for navigation.

V 107

27

24

30

21

33

18

Panoche

VORTAC

(PXN)

15

0

12

3

6

V 230

24

27

33

30

Clovis

VORTAC

(CZQ)

21

18

0

15

3

12

6

KFAT

Figure 6-21 Flight Plan Overview

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-13

6-14

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Departure

Climb to the selected altitude and fly an assigned heading:

1) Upon takeoff, set the Selected Altitude to 7000 feet using the ALT Knob.

To have the autopilot capture this altitude, use

Pitch Hold, Vertical Speed, or Flight Level Change

Mode. In this example, Vertical Speed Mode is used.

2) Upon reaching the desired vertical speed of 1000 fpm, enable the flight director in Vertical Speed

Mode.

a) Press the VS Key. Altitude Hold Mode is armed automatically.

b) Press the AP Key to engage the autopilot in

Roll Hold and Vertical Speed modes.

3) Activate Heading Select Mode while the autopilot is engaged in the climb.

a) Use the HDG Knob to set the Selected Heading to 070°.

b) Press the HDG Key. The autopilot follows the

Heading Bug on the HSI and turns the aircraft to the desired heading.

4) As the aircraft climbs to the Selected Altitude, the flight director changes from Vertical Speed to

Altitude Hold Mode. This active mode change is indicated by the green ‘ALT’ annunciation flashing for ten seconds.

5) Upon reaching the Selected Altitude, the autopilot completes the capture process and levels the aircraft. From this point, the flight director continues to operate in Altitude Hold Mode.

3.

HDG Mode

Selected Altitude of 7,000 MSL

5.

ALT Mode

4.

1.

2.

VS M ode, AL

T M ode Ar med

Figure 6-22 Departure

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

070

Intercepting a VOR Radial

NOTE: Changing the HSI mode cancels

Navigation Mode and causes the flight director to revert to Roll Hold Mode.

During climb-out, the autopilot continues to fly the aircraft in Heading Select Mode. Airway V107 to Panoche

VORTAC (PXN) should now be intercepted.

1) Tune the VOR frequency and activate Heading

Select Mode.

a) Use the CDI Softkey to set the HSI mode to

VOR.

b) Use the CRS Knob to set the Selected Course to 116°. Note that at this point, the flight director is still in Heading Select Mode and the autopilot continues to fly 070°.

SECTION 6 – AUTOMATIC

FLIGHT CONTROL c) Press the NAV Key to arm Navigation Mode.

The white annunciation ‘VOR’ appears to the left of the active roll mode.

2) When the CDI shows less than one dot, the flight director changes from Heading Select to

Navigation Mode, and the green annunciation

‘VOR’ flashes. The autopilot begins turning to intercept the Selected Course.

3) The autopilot continues the turn until the aircraft is established on the Selected Course.

V 107

1.

HDG Mode, VOR Ar med

2.

070

3.

VOR Mode

33

296

30

27

24

Panoche

VORTAC

(PXN)

21

18

Figure 6-23 Intercepting a VOR

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

15

0

3

12

6

6-15

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Flying a GPS Flight Plan

1) Enter Panoche VORTAC (PXN) and Clovis VORTAC

(CZQ) into the GPS flight plan, in preparation to intercept this leg.

2) Transition from VOR to GPS Navigation Mode.

a) Use the CDI Softkey to put the HSI in GPS mode. This cancels VOR mode on the HSI and the flight director loses the VOR signal. As a result, the VOR annunciation flashes yellow.

Flashes for ten seconds, then transitions to ROL..

If the NAV Key is not pressed within 10 seconds of the HSI mode change, the flight director will roll the wings level and enter Roll

Hold Mode.

3) Once the flight plan leg is intercepted, the autopilot continues to track GPS guidance to the end of the flight plan.

b) Press the NAV Key to activate GPS Navigation

Mode to cause the autopilot to steer the aircraft toward the active flight plan leg.

6-16

33

1.

VOR Mode

2.

24

27

30

33 0

3

GPS Mode

Panoche

VORTAC

(PXN)

3.

eg

6

GPS Flight Plan L

21

18

V 230

24

27

12

15

Figure 6-24 Transition to GPS Flight Plan

30

21

18

Clovis

VORTAC

(CZQ)

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

0

15

3

12

6

Flight Level Change (Descent)

While flying the GPS leg from Panoche VORTAC to

Clovis VORTAC, the aircraft is cleared to make a descent to 3000 feet in preparation for the approach to KFAT.

1) Enter Flight Level Change Mode.

a) Using the ALT Knob, set the Selected Altitude to 3000 feet.

b) Press the FLC Key to activate Flight Level

Change Mode. The annunciation ‘FLC’ appears next to the Airspeed Reference, which defaults to the current aircraft airspeed,

142 knots. Altitude Hold Mode is armed automatically.

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

2) Reduce power to allow descent in Flight Level

Change Mode. The autopilot maintains the

Airspeed Reference.

3) Upon capturing the Selected Altitude, the flight director changes from Flight Level Change to

Altitude Hold Mode. The annunciation ‘ALT’ flashes in green to indicate the altitude capture.

After the capture is complete, the autopilot holds the aircraft level at the Selected Altitude.

1.

2.

Cruise Altitude of 7,000 MSL

FLC Mode

3.

Figure 6-25 FLC Descent

Selected Altitude of 3,000 MSL

ALT Hold Mode

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-17

6-18

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

ILS Approach

1) Transition from GPS Navigation Mode to Heading

Select Mode.

a) Load the Runway 29R ILS approach for KFAT into the Flight Plan.

b) Select ‘Vectors to Final’ for the transition.

c) Set the Selected Heading after getting vectors from ATC and press the HDG Key. The autopilot turns the aircraft to the desired heading.

2) Use Heading Select Mode to comply with ATC vectors as requested.

3) In preparation for approach, tune the localizer frequency and select LOC mode on the HSI.

4) Press the APR Key when cleared for approach to arm the Approach Mode. ‘LOC’ and ‘GS’ appear in the armed roll and pitch mode fields, respectively.

The autopilot and flight director determine when to begin the turn to intercept the final approach course.

5) The autopilot flies the ILS Approach. At the

Decision Height, there are two options: push the

AP DISC switch and land the aircraft, or use the

GA button to execute a missed approach (refer to the following procedure).

3 3

Clovis

(CZQ)

6 6

2727 2

1.

GPS Cours e

24

21 21 21

2

12 12

18 18 8 15 15 5

12

2

29

0

KFAT

HDG Mode

2.

Figure 6-26 ILS Approach to KFAT

LOC/GS Mode

5.

02

5

HILAN

4.

075

11

0

3.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Go-Around / Missed Approach

1) Push the GA button at the Decision Height and apply full power to execute a missed approach.

The flight director Command Bars establish a nose-up climb to follow.

Note that when the GA button is pushed, the autopilot disconnects and the ‘AP’ annunciation flashes yellow for five seconds

2) Start the climb to the prescribed altitude in the published Missed Approach Procedure.

a) Press the AP Key to re-engage the autopilot.

b) Set the HSI to GPS mode.

c) Press the NAV Key to have the autopilot fly to the hold.

d) Select the SUSP Softkey to resume sequencing approach legs to the Missed Approach Hold

Point (MAHP). The autopilot flies direct to Clovis VORTAC according to the loaded approach (see Figure 6-27).

3) Use the ALT Knob to set a Selected Altitude to hold. The CWS button may be used to set a new pitch attitude.

As the Selected Altitude is captured, Altitude

Hold Mode becomes active and the autopilot maintains the Selected Altitude.

4) To use the autopilot to fly the hold in Heading

Select Mode, set the Selected Heading using the

HDG Knob and press the HDG Key. Use the HDG

Knob guide the aircraft for the remainder of the hold.

33

0

HDG Mode 30

27

127

4.

CZQ

24

3

6

12

21

18

15

GPS Mode

3.

2.

KFAT

GA Mode

1.

Figure 6-27 Go Around / Missed Approach

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6-19

SECTION 6 – AUTOMATIC

FLIGHT CONTROL

Blank Page

6-20

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 7 – NAVIGATION

SECTION 7: NAVIGATION 7.2 DIRECT-TO NAVIGATION

Direct-to Navigation from the MFD

The following discussions pertain to the Multi Function

Display, unless otherwise indicated.

7.1 NAVIGATION MAP PAGE

Select the MAP Page Group

Identifier

Facility Name

City

Flight Plan Field

Symbol

Nearest Airport

Map Orientation

1) Turn the large FMS Knob until MAP is highlighted in the page group window in the lower right of the MFD display.

2) Turn the small FMS Knob to select the first MAP page (indicated by a solid rectangular icon).

3) Press the MAP Softkey to display softkeys for the available information which may be displayed on the map.

Map of the

Selected

Waypoint

Bearing

Distance

Direct-to

Course

Map Range

Region

Latitude/

Longitude

Activate Field

Figure 7-2 MFD Direct-to Window

WARNING: The map display should only be used for situational awareness. Any map display indication should be compared with approved navigation sources.

Figure 7-1 Navigation Map Page

Enter a Direct-to destination:

1) Press the Direct-to ( ) Key.

2) Turn the small FMS Knob to enter the first letter of the destination waypoint identifier. Turn the large FMS Knob to the right to move the cursor to the next character position.

3) Repeat step 2 to spell out the rest of the waypoint identifier.

4) Press the ENT Key to confirm the identifier. The

‘Activate?’ field is highlighted.

5) Press the ENT Key to activate.

Select a Direct-to destination to a flight plan waypoint or nearest airport:

1) Press the Direct-to ( ) Key.

2) Turn the large FMS Knob to highlight the Flight

Plan Field or Nearest Airport Field.

3) Turn the small FMS Knob to display a list of waypoints or airports.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7-1

7-2

SECTION 7 – NAVIGATION

4) Continue turning the small FMS Knob to scroll through the list and highlight the desired waypoint or airport.

5) Press the ENT Key to confirm the selection.

Press ENT again to activate a Direct-to.

Re-center the CDI (HSI) needle to the same destination waypoint:

1) Press the Direct-to ( ) Key, followed by pressing the ENT Key twice. NOTE: If a missed approach point (MAP) is the current destination, the approach will be canceled.

Manually define the Direct-to course:

1) Press the Direct-to ( ) Key.

2) Turn the FMS Knobs to select the destination waypoint.

3) Press the ENT Key to confirm the selected waypoint, then turn the large FMS Knob to highlight the Direct-to Course field.

4) Turn the FMS Knobs to select the desired course and press the ENT Key.

5) Press the ENT Key again to begin navigation using the selected destination and course.

Canceling Direct-to Navigation:

1) Press the Direct-to ( ) Key.

2) Press the MENU Key to display the Direct-to options menu.

3) With ‘Cancel Direct-To NAV’ highlighted, press the ENT Key. If a flight plan is still active, the

G1000 resumes navigating the flight plan along the closest leg.

Direct-to Navigation from the PFD

WPT Symbol

Identifier

Facility Name

Flight Plan WPT

Bearing to WPT

Distance from WPT

Course to Selected WPT

WPT Location

Nearest WPT

Lat/Lon

Figure 7-4 PFD Direct-to Window

1) Press the Direct-to Key ( ).

2) Turn the large FMS Knob to place the cursor in the desired selection field.

3) Turn the small FMS Knob to begin selecting the desired identifier, location, etc.

4) Press the ENT Key.

5) The cursor is now flashing on ‘ACTIVATE?’.

Press the ENT Key again to activate.

Cancelling Direct-to Navigation:

1) Press the Direct-to ( ) Key.

2) Press the MENU Key to display the Options

Window. The cursor will be flashing on ‘Cancel

Direct-to NAV’.

3) Press the ENT Key to cancel the direct-to.

Figure 7-3 Canceling Direct-to Navigation

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 7 – NAVIGATION

7.3 AIRPORT INFORMATION

6) To remove the flashing cursor, press the FMS

Knob.

Access Runway Information

1) Press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to place the cursor on the Runways field.

3) Turn the small FMS Knob to display the next runway for the selected airport.

4) Continue turning the small FMS Knob to select the desired runway.

5) To remove the flashing cursor, press the FMS

Knob.

Access Frequency Information

Enter a Waypoint Facility Name or City

Location

Figure 7-5 Airport Information Page

Select the Airport Information Page

1) Turn the large FMS Knob to select the ‘WPT’ page group. Turn the small rectangular page icon.

FMS Knob to select the first

1) Press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to select the facility name or location (city) field.

3) Turn the small FMS Knob to select the desired character.

4) Turn the large FMS Knob to select the next character field.

5) Repeat steps 3 and 4 until the facility name or location is selected, then press the ENT Key. If there are duplicate names in the database, a list is displayed from which to chose the desired location.

1) Press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to move the cursor to the Frequencies window.

3) Turn either FMS Knob to scroll through the list, placing the cursor on the desired frequency.

4) Press the ENT Key to place the selected frequency in the standby field of the ‘COM’ or

‘NAV’ window.

5) To remove the flashing cursor, press the FMS

Knob.

• ‘TX’ – transmit only

• ‘RX’ – receive only

• ‘PT’ – part time frequency

• ‘i’ – additional information exists, press the ENT

Key

If a listed frequency has sector or altitude restrictions, the frequency is preceded by an info designation.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7-3

SECTION 7 – NAVIGATION

7.4 INTERSECTION INFORMATION

Select the Intersection Information Page

1) Turn the large FMS Knob to select the WPT page group.

2) Turn the small FMS Knob to select the second rectangular page icon.

7.5 NDB INFORMATION

7-4

Figure 7-6 Intersection Information Page

Access Information on an Intersection

1) With the Intersection Information Page displayed, press the FMS Knob to activate the cursor.

2) Turn the FMS Knobs to enter a name for the identifier and press the ENT Key.

3) Press the FMS Knob to remove the flashing cursor.

Figure 7-7 NDB Information Page

Select the NDB Information Page

1) Turn the large FMS Knob to select the WPT page group.

2) Turn the small FMS Knob to select the third rectangular page icon

View Information on a Specific NDB

1) With the NDB Information Page displayed, press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to highlight the desired selection field (identifier, name or closest city).

3) Turn the FMS Knobs to enter an identifier, name or city and press the ENT Key.

4) Press the FMS Knob to remove the flashing cursor.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7.6 VOR INFORMATION

SECTION 7 – NAVIGATION

7.7 USER WAYPOINT INFORMATION

PAGE

See the Flight Planning section for a discussion on creating and modifying user defined waypoints.

7.8 NEAREST AIRPORTS

Figure 7-8 VOR Information Page

Select the VOR Information Page

1) Turn the large FMS Knob to select the WPT page group.

2) Turn the small FMS Knob to select the fourth rectangular page icon.

Access Information on a VOR

1) With the VOR Information Page displayed, press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to highlight the desired selection field (identifier, name or closest city).

3) Turn the FMS Knobs to enter an identifier, name or city and press the ENT Key.

4) Press the FMS Knob to remove the flashing cursor.

Figure 7-9 Nearest Airports Page

Nearest Airport Information on the MFD

Select the Nearest Airports Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the first rectangular page icon.

Access Information on a Specific Airport

1) Press the APT Softkey located at the bottom of the display. The first airport in the nearest airports list is highlighted.

2) Turn the large FMS Knob to highlight the desired airport.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7-5

SECTION 7 – NAVIGATION

Access Runway Information for the

Selected Airport

1) Press the RNWY Softkey located at the bottom of the display.

2) Turn the small FMS Knob to select the desired runway.

Quickly Tune the COM Transceiver to a

Nearby Airport Frequency

1) Press the FREQ Softkey located at the bottom of the display.

2) Turn either FMS Knob to select the desired frequency.

3) Press the ENT Key. The selected frequency is placed in the standby frequency tuning box.

4) Press the Frequency Transfer Key to place the frequency in the active field.

Nearest Airports Information on the PFD

Bearing TO

Distance

Airport Symbol

2) Press the ENT Key to display airport information.

3) Press the ENT Key again (cursor is on ‘BACK’) to return to the list.

Load an Airport COM Frequency into the

Active COM

1) Turn the large FMS Knob to place the cursor on the desired airport frequency shown in the window.

2) Press the ENT Key and the selected frequency will become the standby frequency for the active COM.

3) Press the Frequency Transfer Key to make the frequency the active frequency.

7.9 NEAREST INTERSECTIONS

Identifier

Runway Length

7-6

Primary COM Frequency

Figure 7-10 Nearest Airports Window

1) Press the NRST Softkey to display the PFD

Nearest Airports Window.

View Information on a Specific Airport in the List

1) Turn the large FMS Knob to place the cursor on the desired airport identifier.

Figure 7-11 Nearest Intersections Page

Select the Nearest Intersections Page

1) Turn the large FMS Knob to select the NRST page group.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 7 – NAVIGATION

2) Turn the small FMS Knob to select the second rectangular page icon.

View Information on the Nearest Intersection

1) Press the FMS Knob to activate the cursor.

2) Turn either FMS Knob to select the desired intersection. Press the ENT Key.

7.10 NEAREST NDB

on the Nearest NDB Page pertains to the selected NDB.

7.11 NEAREST VOR

Select the Nearest VOR Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the fourth rectangular page icon.

Figure 7-12 Nearest NDB Page

Select the Nearest NDB Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the third rectangular page icon.

Access Information on a Specific NDB

1) Press the FMS Knob to activate the cursor.

2) Turn either FMS Knob to select the desired NDB.

Press the ENT Key. The remaining information

Figure 7-13 Nearest VOR Page

View Information on the Nearest VOR

1) With the Nearest VOR Page selected, press the

VOR Softkey.

2) Turn either FMS Knob to select a VOR. Press the ENT Key.

OR Press the MENU Key. Select the Select VOR

Window option and press the ENT Key. Turn either FMS Knob to select a VOR.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7-7

SECTION 7 – NAVIGATION

Select and Load a VOR Frequency

1) With the Nearest VOR Page selected, press the

FREQ Softkey to highlight the VOR frequency for the selected VOR.

2) Press the ENT Key. The selected VOR frequency is placed in the NAV standby frequency field.

OR Press the MENU Key. Select the Select Frequency

Window option and press the ENT Key. Press the ENT Key again when the frequency field is highlighted to place the selected VOR frequency in the NAV standby field.

7.12 NEAREST USER WAYPOINT

Select a Nearest User Waypoint

1) With the Nearest User Waypoint Page selected, press the FMS Knob to activate the cursor.

2) Press the ENT Key to select the Nearest User

Waypoint.

3) The remaining information on the Nearest User

Waypoint Page pertains to the selected Nearest

User Waypoint.

7.13 NEAREST FREQUENCIES

7-8

Figure 7-14 Nearest User Waypoints Page

Select the Nearest User Waypoint Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the fifth rectangular page icon.

Figure 7-15 Nearest Frequencies Page

Select the Nearest Frequencies Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the sixth rectangular page icon.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 7 – NAVIGATION

Select and Load the Nearest ARTCC, FSS, or

Weather Frequency

1) With the Nearest Frequencies Page selected, press the ARTCC, FSS, or Wx Softkey.

2) Turn the large FMS Knob to select the frequency.

3) Press the ENT Key to load the frequency into the ‘COM’ frequency standby field.

7.14 NEAREST AIRSPACES

• If the aircraft is within two nautical miles of an airspace and the current course takes the aircraft inside, ‘Ahead < 2 nm’ is displayed.

• If the aircraft is within two nautical miles of an airspace and the current course will not take the aircraft inside, ‘Within 2 nm’ is displayed.

• If the aircraft has entered an airspace, ‘Inside’ is displayed.

View Additional Details for a Listed Airspace

1) Select the Nearest Airspace Page.

2) Press the FMS Knob to activate the cursor.

3) Turn the large FMS Knob to scroll through the list, highlighting the desired airspace.

4) Press the ALERTS Softkey and turn either FMS

Knob to select the desired airspace.

5) Press the FMS Knob to remove the flashing cursor.

View and Quickly Load the Frequency for a

Controlling Agency

1) Select the Nearest Airspaces Page.

2) Press the FREQ Softkey and turn either FMS

Knob to select the desired frequency. Press the

ENT Key to load the frequency into the ‘COM’ frequency standby field.

Figure 7-16 Nearest Airspaces Page

Select the Nearest Airspaces Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the seventh rectangular page icon.

Airspace Alerts Box

• If the projected course takes the aircraft inside an airspace within the next ten minutes, ‘Ahead’ is displayed.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

7-9

SECTION 7 – NAVIGATION

Blank Page

7-10

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 8 – FLIGHT PLANNING

SECTION 8: FLIGHT PLANNING

The following discussions pertain to the Multi Function

Display, unless otherwise indicated.

8.1 USER DEFINED WAYPOINTS

3) Turn the large FMS Knob to highlight the latitude/longitude field or the Reference

Waypoints field, depending on how the waypoint is to be defined.

4) Turn the FMS Knobs to enter the position coordinates or the radial and distance from the reference waypoint.

5) Press the ENT Key to accept the new waypoint.

6) Press the FMS Knob to remove the flashing cursor.

Create User Waypoints from the Navigation

Map Page

Figure 8-1 User WPT Information Page

Select the User WPT Information Page

1) Turn the large FMS Knob to select the NRST page group.

2) Turn the small FMS Knob to select the fifth rectangular page icon.

Create a New User Waypoint

1) With the User Waypoint Information Page displayed, press the FMS Knob to activate the cursor.

2) Turn the FMS Knobs to enter a name for the new waypoint and press the ENT Key. The message ‘Are you sure you want to create the new user waypoint’ is displayed. With ‘YES’ highlighted, press the ENT Key.

1) With the Navigation Map Page displayed, push the joystick to activate the panning function.

The target pointer is displayed at the present aircraft position.

2) After placing the pointer at the desired position, press the ENT Key. The User Waypoint

Information Page is now displayed with the captured position.

3) Turn the FMS Knobs to select a waypoint name.

4) Press the ENT Key to accept the selected name. The first reference waypoint field is highlighted.

5) If desired, turn the FMS Knobs to enter the identifier of the reference waypoint and the radial and distance to the reference waypoint.

Press the ENT Key to accept.

6) Press the FMS Knob to remove the flashing cursor.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

8-1

SECTION 8 – FLIGHT PLANNING

Modify a User Waypoint

1) With the User Waypoint Information Page displayed, press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to move the cursor to the desired field and turn the small FMS Knob to make changes.

3) Press the ENT Key to accept the changes.

4) Press the FMS Knob to remove the flashing cursor.

Delete a User Waypoint

1) Select the User Waypoint Information Page and press MENU to display the User Waypoint

Information Page Options or press the DELETE

Softkey.

2) Turn the large FMS Knob to select ‘Delete User

Waypoint’ and press the ENT Key. The message

‘Would you like to delete the user waypoint’ is displayed. With ‘YES’ highlighted, press the

ENT Key.

8.2 VIEWING THE ACTIVE FLIGHT PLAN

Press the FPL Key.

Figure 8-3 Active Flight Plan Page on the MFD

8.3 ACTIVATE A STORED FLIGHT PLAN

1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.

8-2

Figure 8-4 Flight Plan Catalog Page

Figure 8-2 Active Flight Plan Window on the PFD 2) Press the FMS Knob to activate the cursor.

3) Turn the large FMS Knob to highlight the desired flight plan and press the ACTIVE Softkey.

4) With OK highlighted, press the ENT Key to activate the flight plan. To cancel the flight plan activation, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 8 – FLIGHT PLANNING

8.4 ACTIVATE A FLIGHT PLAN LEG

1) From the Active Flight Plan Page, press the FMS

Knob to activate the cursor and turn the large

FMS Knob to highlight the desired destination waypoint.

2) Press the ACT LEG Softkey (using MFD only).

OR

3) Press the MENU Key, select the ‘Activate Leg’ option from the page menu and press the ENT

Key. This step must be used when activating a leg from the PFD.

4) With ‘Activate’ highlighted, press the ENT

Key.

flight plan, only the active flight plan.

Figure 8-7 Delete Flight Plan Confirmation

8.6 INVERT ACTIVE FLIGHT PLAN

1) From the Active Flight Plan Page, press the

MENU Key to display the Page Menu.

2) Turn the large FMS Knob to highlight ‘Invert

Flight Plan’ and press the ENT Key. The original flight plan remains intact in its flight plan catalog storage location.

3) With ‘OK’ highlighted, press the ENT Key to invert the flight plan.

Figure 8-5 Activate Flight Plan Leg Confirmation

8.5 STOP NAVIGATING A FLIGHT PLAN

1) Press the FPL Key to display the Active Flight

Plan Page.

2) Press the MENU Key to display the Page Menu window.

Figure 8-8 Invert Flight Plan

Figure 8-9 Invert Flight Plan Confirmation

8.7 CREATE A NEW FLIGHT PLAN

Figure 8-6 Delete Flight Plan

Create a new flight plan using the MFD:

3) Turn the large FMS Knob to highlight ‘Delete

Flight Plan’ and press the ENT Key. With ‘OK’ highlighted, press the ENT Key to deactivate the flight plan. This will not delete the stored

1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

8-3

SECTION 8 – FLIGHT PLANNING

2) Press the NEW Softkey to display a blank flight plan page for the first empty storage location.

8-4

Figure 8-10 Create FPL on MFD

3) Turn the small FMS Knob to display the

Waypoint Information Page. Turn the small

FMS Knob to enter the first character of the identifier of the departure waypoint. Turn the large FMS Knob to move the cursor to the next character field. Repeat using the FMS Knobs until the desired identifier has been entered.

NOTE: After the first leg is entered (using the

PFD only), it is immediately activated.

1) Press the FPL Key and press the small FMS Knob to activate the cursor.

2) Turn the small FMS Knob to enter the first character of the flight plan starting identifier.

3) Turn the large FMS Knob to move the cursor to the next character field.

4) Turn the small FMS Knob to enter the next character. Continue this process until the desired identifier is entered.

5) Press the ENT Key and the cursor is now ready for entering of the next flight plan waypoint.

6) Repeat steps 2 through 5 to enter the identifier for each additional flight plan waypoint.

7) Once all waypoints have been entered, press the FMS Knob to return to the Active Flight Plan

Window.

Figure 8-11 Waypoint Info Window

4) Press the ENT Key.

5) Repeat step number 3 to enter the identifier for each additional flight plan waypoint.

6) When all waypoints have been entered, press the FMS Knob to return to the Flight Plan

Catalog Page. The new flight plan is now in the list.

Create a new flight plan using the PFD

NOTE: A flight plan cannot be entered using the

PFD if another flight plan is active.

Figure 8-12 Creating Flight Plan on the PFD

8.8 LOAD A DEPARTURE

See the Procedures section for a discussion on loading and activating departure procedures.

8.9 LOAD AN ARRIVAL

See the Procedures section for a discussion on loading and activating arrival procedures.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 8 – FLIGHT PLANNING

8.10 LOAD AN APPROACH

See the Procedures section for a discussion on loading and activating approach procedures.

8.11 REMOVE A DEPARTURE, ARRIVAL,

OR APPROACH FROM A FLIGHT PLAN

1) With the Active or Stored Flight Plan Page displayed, press the small FMS Knob to activate the cursor.

2) Turn the large FMS Knob to highlight the title for the approach, departure or arrival to be deleted. Titles appear in white directly above the procedure’s waypoints.

3) Press the CLR Key to display a confirmation window. With ‘OK’ highlighted, press the ENT

Key to remove the selected procedure.

8.12 STORE A FLIGHT PLAN

1) From the Flight Plan Page, press the FMS Knob to activate the cursor.

2) Turn the large FMS Knob to highlight the desired flight plan and press the MENU Key to display the Flight Plan Page options.

3) Turn the large FMS Knob to highlight ‘Store

Flight Plan’ and press the ENT Key.

4) With ‘OK’ highlighted, press the ENT Key to store the flight plan.

8.13 EDIT A STORED FLIGHT PLAN

1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.

2) Press the FMS Knob to activate the cursor.

3) Turn the large FMS Knob to highlight the desired flight plan and press the ENT Key.

4) Turn the FMS Knobs to make the desired changes, then press the ENT Key.

5) Press the FMS Knob to return to the Flight Plan

Catalog Page.

8.14 DELETE A WAYPOINT FROM THE

FLIGHT PLAN

1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.

2) Press the FMS Knob to activate the cursor.

3) Turn the large FMS Knob to highlight the desired flight plan and press the ENT Key.

4) Turn the large FMS Knob to select the waypoint to be deleted and press the CLR Key to display a

‘REMOVE WAYPOINT’ confirmation window.

5) With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel the delete request, turn the large FMS Knob to highlight

‘CANCEL’ and press the ENT Key.

6) Once all changes have been made, press the

FMS Knob to return to the Flight Plan Page.

Figure 8-13 Store Flight Plan Confirmation

Figure 8-14 Remove Waypoint Confirmation

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

8-5

SECTION 8 – FLIGHT PLANNING

8-6

8.15 INVERT AND ACTIVATE A STORED

FLIGHT PLAN

1) From the Flight Plan Catalog Page, press the

FMS Knob to activate the cursor.

2) Turn the large FMS Knob to highlight the desired flight plan and press the MENU Key to display the Page Menu options.

3) Turn the large FMS Knob to highlight ‘Invert

Flight Plan’ and press the ENT Key. The original flight plan remains intact in its flight plan catalog storage location.

4) With ‘OK’ highlighted, press the ENT Key to invert the flight plan.

Figure 8-15 Invert Flight Plan

8.16 COPY A FLIGHT PLAN

1) From the Flight Plan Catalog press the FMS

Knob to activate the cursor, turn the large FMS

Knob to highlight the flight plan to be copied, then press the MENU Key to display the Flight

Plan Catalog Options.

2) Turn the large FMS Knob to highlight ‘Copy

Flight Plan #’ and press the ENT Key.

3) A ‘Copy to flight plan?’ confirmation window is displayed. With ‘OK’ highlighted, press the

ENT Key to copy the flight plan. To cancel, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.

8.17 DELETE A FLIGHT PLAN

1) From the Flight Plan Catalog Page, press the

FMS Knob to activate the cursor, turn the large

FMS Knob to highlight the flight plan to be deleted.

2) Press the MENU Key to display the Flight Plan

Catalog options.

3) Turn the large FMS Knob to highlight ‘Delete

Flight Plan’ and press the ENT Key.

4) A ‘Delete flight plan?’ confirmation window is displayed. With ‘OK’ highlighted, press the

ENT Key to delete the flight plan. To cancel, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.

8.18 GRAPHICAL FLIGHT PLAN CREATION

1) Press the FPL Key to display the Active Flight

Plan Page.

2) Press the joystick to activate the map pointer.

Use the joystick to move the pointer to the desired point on the map to be inserted as a waypoint in the flight plan.

3) Press the LD WPT Softkey. The selected waypoint will be inserted at the end of the flight plan.

4) If the selected waypoint is to be placed elsewhere in the flight plan, press the FMS

Knob to activate the cursor. Waypoints are inserted ABOVE the cursor.

5) After placing the cursor at the desired point in the list of waypoints, press the LD WPT

Softkey.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 8 – FLIGHT PLANNING

8.19 TRIP PLANNING

1) Turn the large FMS Knob to select the AUX page group.

2) Turn the small FMS Knob to select the first rectangular page icon.

3) The current page mode is displayed at the top of the page: ‘AUTOMATIC’ or ‘MANUAL’.

To change the page mode, press the AUTO or

MANUAL Softkey.

Figure 8-16 Trip Planning Page

4) For Direct-to planning, press the WPTS Softkey and verify that the ‘from’ waypoint field indicates

P.POS (present position). If necessary, press the MENU Key and select ‘Set WPT to Present

Position’ to display P.POS. Press the ENT Key and the flashing cursor moves to the ‘to’ waypoint field. Turn the FMS Knobs to enter the identifier of the ‘to’ waypoint and press the ENT Key to accept the waypoint. OR,

5) For point-to-point planning, turn the FMS Knobs to enter the identifier of the ‘from’ waypoint.

Once the waypoints identifier is entered, press the ENT Key to accept the waypoint. The flashing cursor moves to the ‘to’ waypoint.

Again, turn the FMS Knobs to enter the identifier of the ‘to’ waypoint and press the ENT Key to accept the waypoint. OR,

6) For flight plan leg planning, press the FPL Softkey

(at the bottom of the display) and turn the small FMS Knob to select the desired flight plan

(already stored in memory), by number. Turn the large FMS Knob to highlight the ‘LEG’ field and turn the small FMS Knob to select the desired leg of the flight plan, or select ‘CUM’ to apply trip planning calculations to the entire flight plan.

7) Turn the large FMS Knob to highlight the departure time (DEP TIME) field.

NOTE: The departure time on the Trip Planning

Page is used for preflight planning. Refer to the

Utility Page for the actual flight departure time.

8) Turn the FMS Knobs to enter the departure time.

Press the ENT Key when finished. (Departure time may be entered in local or UTC time, depending upon unit settings).

9) Turn the FMS Knobs to enter the fuel flow.

Press the ENT Key when finished. Note that in automatic page mode, fuel flow is provided by the system.

10) The flashing cursor moves to the fuel on board field. Turn the FMS Knobs to modify the fuel on board. Press the ENT Key when finished.

Note that in automatic mode this is provided by the system.

11) The flashing cursor moves to the calibrated airspeed field. Turn the FMS Knobs to enter a calibrated airspeed. Press the ENT Key when finished.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

8-7

SECTION 8 – FLIGHT PLANNING

8.20 VERTICAL NAVIGATION (VNAV) PAGE

NOTE: An active flight plan or Direct-to must be entered in order to utilize VNAV.

NOTE: VNAV is advisory only and cannot be coupled to the autopilot.

5) Press the ENT Key. The cursor is now positioned over the ‘Before’ and ‘After’ field.

6) Turn the small FMS Knob to select whether the previously set distance is ‘Before’ or ‘After’ the endpoint.

7) Press the ENT Key. The cursor is now placed over the VNAV profile endpoint field.

8-8

Figure 8-17 Vertical Navigation (VNAV) Page

Create a Vertical Navigation Profile

1) Press the FPL Key.

2) Turn the small FMS Knob to select the third page icon.

3) Press the FMS Knob to activate the cursor.

4) With the ‘TARGET POSITION’ distance field highlighted, turn the FMS Knobs to select the desired distance for Top Of Climb or Bottom Of

Descent from the VNAV profile endpoint. The default distance is 4 nm.

8) Turn the small FMS Knob to display a list possible VNAV profile endpoints. When using a flight plan, the target reference waypoint itself can be specified from the waypoints contained in the flight plan. By default, the last waypoint in the flight plan is selected. Highlight the desired waypoint.

9) Press the ENT Key.

10) With the ‘TARGET ALTITUDE’ field highlighted, turn the small and large FMS Knobs to select

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 8 – FLIGHT PLANNING the target altitude. If the selected altitude is above the current aircraft altitude, a profiled climb is created. If the selected altitude is below the current aircraft altitude, a profiled descent will be created.

11) Press the ENT Key. The cursor is now placed in the ‘TARGET VERTICAL SPEED’ field. The default profile utilizes a 400 foot-per-minute descent rate.

12) To change the vertical speed, turn the FMS

Knobs to enter the desired vertical speed. Press the ENT Key when finished.

With the profile set, the vertical speed required (VSR) is displayed. Expect the following to occur when using the vertical navigation feature:

At one minute prior to reaching the Bottom Of Climb or Top Of Descent point (gray arc), the message ‘APPR

VPROF - Approaching VNAV Profile’ is displayed as a PFD alert. The descent (or climb) angle also locks to prevent changes in speed from altering the profile. If selected, the vertical speed required (VSR) readout on the default

NAV and map pages shows the desired vertical speed to maintain the proper descent (or climb) angle. At 500 feet above (or below, for a climb) the target altitude (white arc), an ‘APPR TRG ALT’ - Approaching Target Altitude” message is provided. The VSR readout on the Navigation

Map Page is blanked out at this point.

Figure 8-18 Approaching VNAV Profile Message (PFD)

Figure 8-19 Approaching Target Altitude Message (PFD)

To display terrain or topo data on the Vertical

Navigation Map Page, press the MAP Softkey. Press the

TOPO, TERRAIN, or LTNG Softkey. Press the same softkey to remove the displayed data from the Vertical

Navigation Page.

VNAV Page Menu Options

The VNAV messages are not enabled until the ‘VNAV

Messages On?’ option is enabled from the VNAV Page

Menu Options. To display the page menu, press the

MENU Key (with the VNAV Page displayed). The VNAV

Page Options Menu also allows the pilot to restore VNAV page defaults.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

8-9

SECTION 8 – FLIGHT PLANNING

Blank Page

8-10

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 9 – PROCEDURES

SECTION 9: PROCEDURES

9.1 ARRIVALS AND DEPARTURES

Load and Activate a Departure Procedure

1) With the Navigation Map Page displayed, press the FPL Key.

2) Press the LD DP Softkey. If a flight plan is active, the departure airport will be displayed as the default. A list of available departures is also displayed.

3) If no flight plan is active, use the FMS Knobs to enter the identifier of the desired airport.

Press the ENT Key.

4) Turn the large FMS Knob to highlight the

Departure field. Turn the small FMS Knob to display a list of available departures.

5) Turn either FMS Knob to select the desired departure and press the ENT Key.

Figure 9-2 Select Departure Transition

8) With ‘LOAD?’ highlighted, press the ENT Key.

The departure will be active when the flight plan is active.

Load and Activate An Arrival Procedure

1) With the Navigation Map Page displayed, press the FPL Key.

2) Press the LD STAR Softkey. If a flight plan is active, the destination airport will be displayed as the default. A list of available arrivals is also displayed.

3) If no flight plan is active, use the FMS Knobs to enter the identifier of the desired airport.

Press the ENT Key.

4) Turn the large FMS Knob to highlight the Arrival field. Turn the small FMS Knob to display a list of available arrivals.

5) Turn either FMS Knob to select the desired arrival and press the ENT Key.

Figure 9-1 Select Departure

6) A list of runways may be displayed for the departure. Turn either FMS Knob to select the desired runway and press the ENT Key.

7) A list of available transitions is displayed for the departure. Turn either FMS Knob to highlight the desired transition waypoint and press the

ENT Key.

Figure 9-3 Select Arrival

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

9-1

9-2

SECTION 9 – PROCEDURES

6) A second window is displayed listing available transitions for the arrival. Turn either FMS Knob to highlight the desired transition waypoint and press the ENT Key.

Figure 9-4 Select Arrival Transition

7) A third window is displayed listing the available runways. Turn either FMS Knob to select the desired runway and press the ENT Key.

will not have this designation, meaning the GPS receiver can be used for supplemental navigation guidance only.

If the GPS receiver cannot be used for primary guidance, the appropriate navigation receiver must be used for the selected approach (e.g., VOR or ILS). The final course segment of ILS approaches, for example, must be flown by tuning the Nav receiver to the proper frequency and selecting that Nav receiver on the CDI.

Load and/or Activate an Approach Procedure

1) With the Navigation Map Page displayed, press the FPL Key.

2) Press the LD APR Softkey. If a flight plan is active, the destination airport will be displayed as the default. A list of available approaches is also displayed.

3) If no flight plan is active, use the FMS Knobs to enter the identifier of the desired airport.

Press the ENT Key.

4) Turn the large FMS Knob to highlight the

Approach field. Turn the small FMS Knob to display a list of available approaches.

Figure 9-5 Select Arrival Runway

8) With ‘LOAD?’ highlighted, press the ENT Key.

If a flight plan is active, the selected arrival procedure is inserted after the destination airport and becomes part of the active flight plan. If no flight plan is active when the arrival is loaded, the arrival procedure will become the active flight plan.

9.2 APPROACHES

Not all approaches in the database are approved for GPS use. When selecting an approach, a “GPS” designation to the right of the procedure name indicates the procedure can be flown using the GPS receiver. Some procedures

Figure 9-6 Selecting an Approach Procedure

5) Turn either FMS Knob to highlight the desired approach. Press the ENT Key.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

6) The cursor will move to the TRANSITIONS field. Turn the large FMS Knob to highlight the desired transition waypoint and press the ENT

Key. (The “Vectors” option assumes vectors will be received to the final course segment of the approach and will provide navigation guidance relative to the final approach course.)

SECTION 9 – PROCEDURES

Figure 9-7 Selecting an Approach Transition

7) Turn the large FMS Knob to highlight ‘Activate?’ and press the ENT Key to activate the approach.

Selecting ‘Load?’ will add the procedure to the flight plan without immediately using it for navigation guidance.

Activate An Approach in the Active Flight Plan

1) With the Navigation Map Page displayed, press the PROC Key.

2) Turn the large FMS Knob to highlight ‘ACTIVATE

APPROACH’.

3) Press the ENT Key. The approach procedure is now active.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

9-3

SECTION 9 – PROCEDURES

Blank Page

9-4

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 10: HAZARD AVOIDANCE

10.1 CUSTOMIZING THE HAZARD

DISPLAYS ON THE NAVIGATION MAP

1) With the Navigation Map Page displayed, press the MENU Key to display the Navigation Map

Page Menu. The cursor flashes on the ‘Map

Setup’ option.

2) Press the ENT Key. The Map Setup Menu is displayed. Turn the small FMS Knob to select the ‘Weather’ or ‘Traffic’ group to customize the display of weather features. Select ‘Traffic’ to customize the display of traffic.

3) Press the small FMS Knob to return to the

Navigation Map Page.

SECTION 10 – HAZARD

AVOIDANCE

10.2 STORMSCOPE® (OPTIONAL)

WARNING: The Stormscope system is not intended to be used for hazardous thunderstorm penetration. Weather information on the G1000

MFD is approved for weather avoidance only.

Refer to the WX-500 Pilot’s Guide for detailed operation.

Displaying Stormscope Lightning Data on the

Navigation Map Page

1) Press the MAP Softkey.

2) Press the STRMSCP Softkey. Press the STRMSCP

Softkey again to remove Stormscope Lightning

Data from the Navigation Map Page.

Figure 10-1 Page Menu

Figure 10-2 Map Setup Menu

Figure 10-4 In-Flight Navigation Map Page Displaying

Stormscope Lightning Data

Figure 10-3 Map Setup Group List

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-1

SECTION 10 – HAZARD

AVOIDANCE

At a map range of less than 25 nm, Stormscope lightning data is not displayed, but can still be present.

The presence of Stormscope lightning data is indicated by the annunciation ‘LTNG < 25 nm’ in the upper right corner.

Stormscope Page

1) Turn the large FMS Knob until the Map Page group is selected.

2) Turn the small FMS Knob until the Stormscope

Page is selected. This is the third rectangular page icon.

10-2

Figure 10-5 Lightning Display Range Annunciation

Select ‘cell’ or ‘strike’ as the Stormscope lightning mode:

1) With the Weather Group selected, press the

ENT Key. The cursor flashes on ‘STRMSCP

LTNG’.

2) Turn the large FMS Knob to select ‘STRMSCP

MODE’.

3) Turn either FMS Knob to display the ‘Cell/Strike’ window.

4) Turn either FMS Knob to select ‘Cell’ or ‘Strike’.

Press the ENT Key.

5) Push the FMS Knob to return to the Navigation

Map Page.

Clear Stormscope lightning data from the

Navigation Map Page:

1) Press the MENU Key (with the Navigation Map

Page displayed).

2) Turn either FMS Knob to highlight the ‘Clear

Lightning Data’ field and press the ENT Key.

NOTE:

If heading input is lost, strikes and/or cells must be cleared manually after the execution of each turn. This is to ensure that the strike and/or cell positions are depicted accurately in relation to the nose of the aircraft.

Figure 10-6 Stormscope Page

Change the Stormscope lightning mode between ‘cell’ and ‘strike’:

1) Select the Stormscope Page.

2) Press the MODE Softkey. The CELL and STRIKE

Softkeys are displayed. Press the CELL Softkey to display ‘CELL’ data or press the STRIKE

Softkey to display ‘STRIKE’ data. ‘CELL’ or

‘STRIKE’ is displayed in the mode box located in the upper left corner of the Stormscope Page.

NOTE: “Cell mode” uses a clustering program to identify clusters of electrical activity that indicate cells.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 10 – HAZARD

AVOIDANCE

Change the viewing mode between 360˚ and

120˚:

1) Select the Stormscope Page.

2) Press the VIEW Softkey. The 360 and ARC

Softkeys are displayed. Press the 360 Softkey to display a 360˚ viewing area or press the ARC

Softkey to display a 120˚ viewing area.

Press the CLEAR Softkey to remove all

Stormscope lightning data from the display.

10.3 XM WEATHER (OPTIONAL)

WARNING: XM Weather is not intended to be used for hazardous weather penetration.

Weather information provided by XM Radio

Service is approved only for weather avoidance, not penetration.

1) Press the MAP Softkey.

2) Press the NEXRAD or XM LTNG Softkey to display the desired weather. Press the applicable softkey again to remove weather data from the Navigation Map Page.

Displaying METAR and TAF information on the

Airport Information Page

Display METAR and TAF text on the Airport

Information Page:

1) Turn the large FMS Knob to select the WPT Page

Group.

2) Turn the small FMS Knob to select the Airport

Information Page.

3) Press the WX Softkey to display METAR and

TAF text (METAR and TAF information is updated every 12 minutes).

METAR

Text

TAF

Text

WX

Softkey

Figure 10-8 METAR and TAF Text Displayed on the

Airport (Weather) Information Page

Figure 10-7 Navigation Map Page Displaying NEXRAD Weather

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-3

10-4

SECTION 10 – HAZARD

AVOIDANCE

Displaying Weather on the Weather Data Link

Page

Select the Weather Data Link Page:

1) Turn the large FMS Knob to select the Map

Page Group.

2) Turn the small FMS Knob to select the fourth rectangular page icon.

3) Press the available softkeys to select the desired

XM weather product.

4) Press the LEGEND Softkey to view the legends for the selected products. If necessary, turn either FMS Knob to scroll through the list.

Press the small FMS Knob or the ENT Softkey to return to the map.

NEXRAD Limitations

Certain limitations exist regarding the NEXRAD radar displays. Some, but not all, are listed here:

• NEXRAD base reflectivity does not provide sufficient information to determine cloud layers or precipitation characteristics (hail vs. rain, etc).

• An individual NEXRAD site cannot depict high altitude storms at close ranges, and has no information about storms directly over the site.

• The resolution of displayed NEXRAD data is 4 square kilometers. Therefore, when zoomed in on the display, each square block is 2 kilometers on each side. The intensity level reflected by the square will be the highest level sampled within the square area.

ECHO TOP – Press the ECHO TOP Softkey to show the location, elevation, and direction the highest radar echo. This may not indicate the top of a storm or clouds, only the highest radar return echo. ECHO TOPS cannot be displayed along with NEXRAD and CLOUD TOPS. When ECHO

TOPS is activated, NEXRAD and CLOUD TOPS are removed. Refer to the Legend for a description of the ECHO TOPS coding. The display is updated every 7.5 minutes.

CLD TOP – Press the CLD TOP Softkey to show the cloud top altitude determined from satellite imagery.

The display is updated every 15 minutes.

LTNG – Pressing the LTNG Softkey shows the location of cloud-to-ground lightning strikes. The display is updated every five minutes.

Figure 10-9 Weather Data Link Page

NEXRAD – Press the NEXRAD Softkey to show

NEXRAD weather and radar coverage information.

Areas where radar coverage is not available will be shown in grayish-purple. The display is updated every five minutes.

NOTE: Strikes depicted represent cloud to ground strikes within a 2 kilometer radius of the actual strike location. Therefore, the exact location of the strike is not displayed.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 10 – HAZARD

AVOIDANCE

CELL MOV – Pressing the CELL MOV Softkey shows storm cell movement by displaying an arrow. pointing in the direction of predicted movement.

The display is updated every 12 minutes.

SIG/AIR – Pressing the SIG/AIR Softkey shows

SIGMET and AIRMET information. The display is updated every 12 minutes.

METAR – Press the METAR Softkey to graphically display METARs. METARS are shown as colored flags at airports providing METAR reports. The display is updated every 12 minutes.

MORE WX – Press the MORE WX Softkey to display the following group of softkeys for additional weather control:

SFC – Pressing the SFC Softkey for Surface Analysis shows current or forecast conditions. Forecasts are available for intervals of Current, 12, 24, 36, and 48 hours. Press the softkey corresponding to the desired forecast. The closest city forecast information is displayed in the legend. The display is updated every 12 minutes.

FRZ LVL – Press the FRZ LVL Softkey to display contour lines for freezing levels. The display is updated every 12 minutes.

WIND – Press the WIND Softkey to show wind speed and direction at a selected altitude from the ground up to 42,000 feet in 3,000 foot increments. After pressing the WIND Softkey, press the softkey corresponding to the desired winds aloft altitude. The display is updated every

12 minutes.

COUNTY – Pressing the COUNTY Softkey provides specific public awareness and protection weather warnings for Tornado, Severe Thunderstorm, and Flood conditions provided by the National

Weather Service (NWS). The display is updated every 5 minutes.

Map Panning Information – Weather Data Link

Page

CYCLONE – Pressing the CYCLONE Softkey shows the current location of cyclones (hurricanes and tropical storms) and their projected track at various time intervals. The update rate is every

12 minutes.

1) Push in the joystick to display the panning arrow.

2) Move the joystick to place the panning arrow on AIRMETs, TFRs, METARs, or SIGMETs. Press the ENT Key to display pertinent information for the selected product.

Note that pressing the ENT Key when panning over an AIRMET or a SIGMET displays an information box that displays the text of the report. Panning over an airport with METAR information does not display more information but allows the user to press the ENT Key and select that Airport’s Information Page to display the text of the report. Pressing the ENT Key when panning over a TFR displays TFR specific information.

Weather Products and Symbols

Figure 10-10 depicts the symbol for each weather product (read from left to right). When a weather product is active, the product symbol is displayed in the lower right of the screen.

• NEXRAD

• Cloud Top/Echo Top

• XM Lightning

• Cell Movement

• SIGMETs/AIRMETs

• METARs

• City Forecast

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-5

SECTION 10 – HAZARD

AVOIDANCE

• Surface Analysis

• Freezing Levels

• Winds Aloft

• County Warnings

• Cyclone Warnings

Echo Top (Cloud Top and Echo Top Mutually Exclusive)

10-6

Figure 10-10 Weather Product Symbols

The XM Information Page in the AUX Page Group will display the weather products available for the current subscription. A green box by the weather product means that it is available.

NOTE: The DONE Softkey on the AUX - XM

INFORMATION page is used to save the GDL

69(A) activation data when the XM services are initially set up. It is not used during normal operation of the GDL 69(A), and it should have no adverse effects if inadvertently selected during flight. Refer to the GDL 69/69A XM Satellite

Radio Activation Instructions (190-00355-04, Rev

E or later) for further information.

Weather Product Age

The age for each of the enabled products is displayed on the right side of the display. Times are based on Zulu time when the data was assembled on the ground, not the time the data was received by the XM receiver. When the age of a weather product has exceeded half of the expiration time, the product time will change from light blue to amber in color.

Weather Product

SIGMETs/AIRMETs

City Forecasts

County Warnings

Cyclone Warnings

Echo Tops

Freezing Levels

METARs

Lightning

NEXRAD

Radar Coverage

Cell Movement

Surface Analysis

TFRs

Winds Aloft

TAFs

Clouds Tops

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

60

60

60

30

30

30

30

60

60

Expires After

(minutes)

60

60

60

60

30

60

90

SECTION 10 – HAZARD

AVOIDANCE

10.4 TRAFFIC INFORMATION SERVICE

(TIS)

Traffic Mode

Traffic Advisory, aircraft is 400’ above & descending, moving in the direction of the line

Traffic out of range

NOTE: If the G1000 is configured to use the optional Skywatch Traffic Advisory System, TIS will not be available for use.

NOTE: Traffic Information Service (TIS) is only available when the aircraft is within the service volume of a TIS capable terminal radar site.

Displaying Traffic on the Traffic Map Page

1) Turn the large FMS Knob to select the Map

Page Group.

2) Turn the small FMS Knob to select the second rectangular page icon.

3) Press the OPERATE Softkey to begin displaying traffic. ‘TIS OPERATIING’ is displayed in the

Traffic mode field.

4) Press the STANDBY Softkey to place the system in the Standby mode. ‘TIS STANDBY’ will be displayed in the Traffic mode field.

5) Rotate the joystick clockwise to display a larger area or rotate counter-clockwise to display a smaller area.

If data is not received for a period longer than 6 seconds, the age of the present data will be displayed in the lower left of of the screen along with the annuciation that the system has entered Coast mode. The system will maintain the traffic display (up to 60 seconds) until the next data reception. If no data is received after 60 seconds, traffic will be removed from the display.

Last data update is older than 6 sec. resulting in

Coast mode

Proximity Traffic at same altitude, level flight & moving in the direction of the line

Traffic 1600’ above & climbing, moving in the direction of the line

Figure 10-11 Traffic Map Page

Displaying Traffic on the Navigation Map

1) Ensure TIS is operating. With the Navigation

Map displayed, press the MAP Softkey.

2) Press the TRAFFIC Softkey. Traffic will now be displayed on the map.

TIS Audio Alert

When a Traffic Advisory (TA) is displayed, an audio alert “Traffic” is given.

“Traffic Not Available” will be heard whenever TIS service becomes unavailable.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-7

SECTION 10 – HAZARD

AVOIDANCE

10.5 SKYWATCH TRAFFIC ADVISORY

SYSTEM (TAS)(OPTIONAL)

Refer to the SkyWatch pilot’s guide for a detailed discussion of the SkyWatch system.

Displaying Traffic on the Traffic Map Page

1) Turn the large FMS Knob to select the Map

Page Group.

2) Turn the small FMS Knob to select the second rectangular page icon.

3) Press the OPERATE Softkey to begin displaying traffic. ‘TAS OPERATING’ is displayed in the

Traffic mode field.

4) Press the ALT MODE Softkey to change the altitude volume. Select the desired altitude volume by pressing the the BELOW, NORMAL,

ABOVE, or UREST (unrestricted) Softkey. The selection is displayed in the Altitude mode field.

5) Press the STANDBY Softkey to place the system in the Standby mode. ‘TAS STANDBY’ will be displayed in the Traffic mode field.

6) Rotate the joystick clockwise to display a larger area or rotate counter-clockwise to display a smaller area.

Traffic Mode Altitude Mode

Traffic Advisory, aircraft is 400’ below

& climbing

Traffic, Out of

Range

“Non-Bearing” Traffic (system is unable to determine bearing), distance is 8.0 nm, 1190’ above and descending

Proximity Traffic,

1000’ above & descending

Figure 10-12 Traffic Map Page

Displaying Traffic on the Navigation Map

1) Ensure the SkyWatch system is operating. With the Navigation Map displayed, press the MAP

Softkey.

2) Press the TRAFFIC Softkey. Traffic will now be displayed on the map.

10-8

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Traffic Advisory

SECTION 10 – HAZARD

AVOIDANCE

4) Rotate the JOYSTICK clockwise to display a larger area or rotate counter-clockwise to display a smaller area.

Non-Bearing

Traffic Advisories

Traffic Off Scale

Banner

Non-Threat

Traffic

Figure 10-13 TAS Traffic on Navigation Map Figure 10-14 Terrain Proximity Page

10.6 TERRAIN AND OBSTACLE PROXIMITY

NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75 degrees north or 60 degrees south.

Color

RED

YELLOW

Indication

Terrain/Obstacle at or within 100’ below or above aircraft altitude.

Terrain/Obstacle between 100’ and 1000’ below current aircraft altitude.

Displaying Terrain and Obstacles on the Terrain

Proximity Page

100' Threshold

Aircraft Altitude

1) Turn the large FMS Knob to select the Map

Page Group.

2) Turn the small FMS Knob to select the last rectangular page icon.

3) If desired, press the VIEW Softkey to access the

ARC and 360 Softkeys. When the ARC Softkey is pressed, a radar-like 120° view is displayed.

Press the 360 Softkey to return to the 360° default display.

1000'

Displaying Terrain and Obstacles on the

Navigation Map

1) With the Navigation Map displayed, press the

MAP Softkey.

2) Press the TERRAIN Softkey. Terrain and obstacle proximity will now be displayed on the map.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-9

10-10

SECTION 10 – HAZARD

AVOIDANCE

Unlighted Obstacle

(Height is less than

1000’ AGL)

Lighted Obstacle

(Height is less than

1000’ AGL)

Unlighted Obstacle

(Height is greater than

1000’ AGL)

Figure 10-15 Obstacle Symbols

10.7 TERRAIN AWARENESS & WARNING

SYSTEM (TAWS) DISPLAY (OPTIONAL)

NOTE: Terrain data is not displayed when the aircraft latitude is greater than 75 degrees north or 60 degrees south.

NOTE: TAWS operation is only available when the

G1000 is configured for a TAWS-B installation.

Displaying Terrain on the TAWS Page

1) Turn the large FMS Knob to select the Map

Page Group.

2) Turn the small FMS Knob to select the TAWS

Page.

3) If desired, press the VIEW Softkey to access the

ARC and 360 Softkeys. When the ARC Softkey is pressed, a radar-like 120° view is displayed.

Press the 360 Softkey to return to the 360° default display.

4) Rotate the JOYSTICK clockwise to display a larger area or rotate counter-clockwise to display a smaller area.

Lighted Obstacle

(Height is greater than

1000’ AGL)

Figure 10-16 TAWS Page (360˚ View)

Figure 10-17 TAWS Page (ARC View)

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

1000'

Color

Red

Yellow

Black

SECTION 10 – HAZARD

AVOIDANCE

Terrain/Obstacle Location

Terrain/Obstacle at or within 100’ below or above aircraft altitude.

Terrain/Obstacle between 100’ and

1000’ below current aircraft altitude.

Terrain/Obstacle is more than 1000’ below aircraft altitude.

Suggested Pilot Response

Initiate climb and/or turn away from terrain/obstacle.

Be aware of surroundings.

Be prepared to take action.

No action required.

Potential Impact Point

Projected Flight Path

100' Threshold

Unlighted Obstacle

Enable/Disable Aviation Data

1) While the TAWS Page is displayed, press the

MENU Key.

2) Turn the small FMS Knob to select “Show (or

Hide) Aviation Data”.

3) Press the ENT Key.

Figure 10-18 TAWS Page Menu

TAWS Inhibit

Flying VFR into an area where unique terrain exists could cause the system to annunciate a nuisance alert.

When TAWS is inhibited, only FLTA and PDA alerts are disabled.

Inhibit TAWS:

1) While the TAWS Page is displayed, press the

MENU Key.

2) Turn the small FMS Knob to select‘Inhibit

TAWS’.

3) Press the ENT Key.

Enable TAWS:

1) While the TAWS Page is displayed, press the

MENU Key.

2) Turn the small FMS Knob to select ‘Enable

TAWS’.

3) Press the ENT Key.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-11

10-12

SECTION 10 – HAZARD

AVOIDANCE

Manual System Test

A system test is automatically performed at power-up.

After sucessful completion of the test, “TAWS System

Test, OK” will be heard.

The system test may also be initiated manually, but only when the aircraft is on the ground. To manually verify proper operation of the aural and visual annunciations of the system, perform the following steps.

1) While the TAWS Page is displayed, press the

MENU Key.

2) Turn the small FMS Knob to select ‘Test

TAWS’.

3) Press the ENT Key. During the test ‘TAWS TEST’ is displayed in the center of the TAWS Page.

When all is in working order, “TAWS System

Test, OK” will be heard.

Forward Looking Terrain Avoidance (FLTA)

The Forward Looking Terrain Avoidance alert is composed of two sub-functions:

Reduced Required Terrain Clearance (RTC) and

Reduced Required Obstacle Clearance (ROC)

This provides alerts when the aircraft flight path is above terrain and/or obstacles, yet is projected to come within minimum clearance values outlined in the following table. When an RTC or ROC alert is issued, a potential impact point is displayed on the TAWS Page as a yellow or red ‘X’.

Imminent Terrain Impact (ITI) and Imminent

Obstacle Impact (IOI)

This provides alerts when the aircraft is below the elevation of terrain in the aircraft’s projected path. ITI and

IOI alerts are accompanied by a potential impact point displayed on the TAWS Page as a yellow or red ‘X’. The alert is given when the projected vertical flight path is calculated to come within minimum clearance altitudes in the following table.

Phase of Flight

Enroute

Terminal

Approach

Departure

Level Flight

700 ft.

350 ft.

150 ft.

100 ft.

Descending

500 ft.

300 ft.

100 ft.

100 ft.

During the final approach phase of flight, RTC/ROC/

ITI/IOI alerts are automatically inhibited when the aircraft is below 200 feet AGL while within 0.5 nm of the approach runway or is below 125 feet AGL while within 1 nm of the runway.

Premature Descent Alert (PDA)

A Premature Descent Alert is issued when the system detects that the aircraft is significantly below the normal approach path to a runway. The PDA alert mode functions only during descent to land.

PDA alerting begins when the aircraft is within 15 nm of the destination airport and ends when the aircraft is either 0.5 nm from the runway threshold OR is at an altitude of 125 feet AGL while within 1 nm of the threshold.

During the final descent, algorithms will set a threshold for alerting based on speed, distance, and other parameters.

Figure 10-19 PDA Alerting

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 10 – HAZARD

AVOIDANCE

1500

1000

500

0

4500

4000

3500

3000

2500

2000

Excessive Descent Rate Alert (EDR)

The purpose of the Excessive Descent Rate alert is to provide suitable alerts when the aircraft is determined to be closing (descending) upon terrain at an excessive speed. Figure 10-20 displays the correlation between height above terrain and descent rate, resulting in the two

EDR alerts. EDR alerts have two levels of severity, caution

(sink rate) and warning (pull-up).

5000

"SINK RA

TE

"

2000 4000 6000 8000

Descent Rate (FPM)

10000 12000

Figure 10-20 Excessive Descent Rate

Negative Climb Rate After Takeoff

Alert (NCR)

The purpose of the Negative Climb Rate After Takeoff alert is to provide suitable alerts to the pilot when the system determines that the aircraft is losing altitude

(closing upon terrain) after takeoff. The aural message

Don’t Sink” is given for NCR alerts, accompanied by an annunciation and a pop-up terrain alert on the display.

“Five-Hundred” Aural Alert

The purpose of the aural alert message “Five-hundred” is to provide an advisory alert to the aircrew that the aircraft is five-hundred feet above terrain. When the aircraft descends within 500 feet of terrain, the aural message “Five-hundred” is heard. There are no display annunciations or pop-up alerts that accompany the aural message.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-13

SECTION 10 – HAZARD

AVOIDANCE

Displaying Terrain and Obstacles on the

Navigation Map

1) With the Navigation Map displayed, press the

MAP Softkey.

2) Press the TERRAIN Softkey. Terrain and obstacle proximity will now be displayed on the map.

Unlighted Obstacle

(Height is less than

1000’ AGL)

Lighted Obstacle

(Height is less than

1000’ AGL)

Unlighted Obstacle

(Height is greater than

1000’ AGL)

Figure 10-21 TAWS Symbols

Lighted Obstacle

(Height is greater than

1000’ AGL)

Potential Impact Points

Pop-up Alerts

When a terrain or obstacle alert is issued, a pop-up window is displayed on the MFD with the appropriate alert.

10-14

Figure 10-22 Alert Pop-Up

Press the ENT Key to display the TAWS Page, or press the CLR Key to remain on the existing page.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 10 – HAZARD

AVOIDANCE

TAWS Alerts Summary

The following table shows the possible TAWS alert types with corresponding annunciations and aural messages.

Alert Type

PFD/MFD TAWS

Page

Annunciation

MFD

Pop-Up Alert

Aural Message

Excessive Descent Rate Warning (EDR) “Pull Up”

Reduced Required Terrain Clearance Warning (RTC) or

Imminent Terrain Impact Warning (ITI)

Reduced Required Obstacle Clearance

Warning (ROC)

Imminent Obstacle Impact Warning (IOI)

Reduced Required Terrain Clearance Caution

(RTC)

Imminent Terrain Impact Caution (ITI)

Reduced Required Obstacle Clearance

Caution (ROC)

Imminent Obstacle Impact Caution (IOI)

Premature Descent Alert Caution (PDA)

Altitude Callout “500”

Excessive Descent Rate Caution (EDR)

Negative Climb Rate Caution (NCR)

None or or or or or or or

None or

“Terrain, Terrain; Pull Up, Pull Up” or

“Terrain Ahead, Pull Up; Terrain Ahead, Pull Up”

Terrain Ahead, Pull Up; Terrain Ahead, Pull Up” or

“Terrain, Terrain; Pull Up, Pull Up”

“Obstacle, Obstacle; Pull Up, Pull Up” or

“Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up”

“Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up” or

“Obstacle, Obstacle; Pull Up, Pull Up”

“Caution, Terrain; Caution, Terrain” or

“Terrain Ahead; Terrain Ahead”

“Terrain Ahead; Terrain Ahead” or

“Caution, Terrain; Caution, Terrain”

“Caution, Obstacle; Caution, Obstacle” or

“Obstacle Ahead; Obstacle Ahead”

“Obstacle Ahead; Obstacle Ahead” or

“Caution, Obstacle; Caution, Obstacle”

“Too Low, Terrain”

“Five-Hundred”

“Sink Rate”

“Don’t Sink” or

“Too Low, Terrain”

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

10-15

SECTION 10 – HAZARD

AVOIDANCE

The following system status annunciations may also be issued.

Alert Type

PFD/MFD TAWS

Page

Annunciation

TAWS System Test Fail

TAWS Alerting is disabled

No GPS position or excessively degraded

GPS signal

MFD

Pop-Up Alert

None

None

None

System Test in progress

System Test pass

Alert Annunciations

None

None

None

Aural Message

“TAWS System Failure”

None

“TAWS Not Available”

“TAWS Availble” will be heard when sufficient

GPS signal is re-established.

None

“TAWS System Test OK”

Alert Annunciation

10-16

Alert Annuciation

Figure 10-23 Alert Annunciation on the TAWS Page

Figure 10-24 Alert Annunciation on the PFD

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 11 – ABNORMAL

OPERATION

SECTION 11: ABNORMAL

OPERATION

11.1 REVERSIONARY MODE

Should a system detected failure occur in either display, the G1000 automatically enters reversionary mode. In reversionary mode, critical flight instrumentation is combined with engine instrumentation on the remaining display. Minimal navigation capability is available on the reversionary mode display.

Reversionary display mode can also be manually activated by the pilot if the system fails to detect a display problem. The reversionary mode is activated manually by pressing the red DISPLAY BACKUP button on the bottom of the audio panel (GMA 1347). Pressing the red

DISPLAY BACKUP button again deactivates reversionary mode.

NOTE: The Beechcraft A36/G36 Pilot’s Operating

Handbook (POH) always takes precedence over the information found in this section.

Normal PFD Display Normal MFD Display

MFD in Reversionary Mode

Figure 11-1 G1000 Reversionary Mode: Failed PFD

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

11-1

SECTION 11 – ABNORMAL

OPERATION

11.2 ABNORMAL COM OPERATION

When a COM tuning failure is detected by the system, the emergency frequency (121.500 MHz) is automatically loaded into the active frequency field of the COM radio for which the tuning failure was detected. In the event of a dual display failure, the emergency frequency (121.500

MHz) automatically becomes the active frequency to the pilot through the pilot headset.

11.3 UNUSUAL ATTITUDES

The PFD will ‘declutter’ when the aircraft enters an unusual attitude. Only the basic primary functions will be displayed in these situations.

Red extreme pitch warning chevrons pointing toward the horizon are displayed starting at 50 degrees above and

30 degrees below the horizon line.

11.5 HAZARD DISPLAYS WITH LOSS OF

GPS POSITION

If GPS position is lost, or becomes invalid, selected hazards being displayed on the Navigation Map Page will be removed until GPS position is again established.

The icons in the lower right of the screen, indicating the selected functions for display, will show an ‘X’, as shown in Figure 11-3.

Figure 11-3 Loss of Hazard Functions with Loss of GPS Position

11-2

Figure 11-2 Extreme Pitch Indication

11.4 STORMSCOPE OPERATION WITH

LOSS OF HEADING INPUT

If heading is lost, strikes and/or cells must be cleared manually after the execution of each turn. This is to ensure that the strike and/or cell positions are depicted accurately in relation to the nose of the aircraft.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

SECTION 12: ANNUNCIATIONS &

System

Annunciation

Red ‘X’

ALERTS

NOTE: The Beechcraft A36/G36 Pilot’s Operating

Handbook (POH) supersedes information found in this document.

Annunciation

Window

Alerts Window

Figure 12-1 G1000 Alerting System

WARNING,

CAUTION,

ADVISORY, and

ALERTS Softkey

Annunciation

The G1000 Alerting System conveys alerts to the pilot using a combination of the following items:

• Annunciation Window: The Annunciation window displays abbreviated annunciation text.

The Annunciation Window is located to the right of the Altitude and Vertical Speed windows on the PFD display (or the MFD if system is in reversionary mode). All A36/G36 annunciations can be displayed simultaneously. A white horizontal line separates annunciations that are acknowledged from annunciations that are not yet acknowledged.

Acknowledged annunciations are always above the line. Annunciations are displayed in order of priority from top to bottom. The highest priority annunciation is displayed at the top of the

Annunciation Window.

• Alerts Window: The Alerts window displays annunciation and alert message text. Up to 64 prioritized alerts can be displayed in the Alerts

Window. Pressing the ALERTS Softkey displays the

Alerts Window. Pressing the ALERTS Softkey again removes the Alerts Window from the display. When the Alerts Window is displayed, the pilot may use the large FMS Knob to scroll through the alert list.

Higher priority alerts are displayed at the top of the window. Lower priority alerts are displayed at the bottom of the window. Active alerts are displayed in white text. Alerts that have become inactive will change to gray text. The ALERTS Softkey will flash if the state of a displayed alert changes or a new alert is displayed. The inactive alerts can be removed from the Alerts window by pressing the flashing

ALERTS Softkey.

• ALERTS Softkey Annunciation: When an alert is issued, the ALERTS Softkey is used as a flashing annunciation to accompany an alert. During the alert, the ALERTS Softkey assumes a new label consistent with alert level (WARNING, CAUTION, or ADVISORY). Pressing the softkey annunciation acknowledges that the pilot is aware of the alert.

The softkey then returns to the previous ALERTS label. The pilot can then press the ALERTS Softkey again to view alert text messages.

• System Annunciations: Typically, a large red ‘X’ appears in a window when a related LRU fails or

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-1

SECTION 12 – ANNUNCIATIONS

& ALERTS

12-2 detects invalid data. A red ‘X’ is accompanied by an alert message in the Alerts Window.

• Audio Alerting System: The G1000 system issues audio alert tones when specific system conditions are met. See the Alert Levels Definitions section for more information.

12.1 ALERT LEVEL DEFINITIONS

The G1000 Alerting System, as installed in Beechcraft

A36/G36 aircraft, uses four alert levels.

• WARNING: This level of alert is time critical and requires immediate pilot attention. A warning annunciation is displayed in the Annunciation

Window as red text. A warning annunciation is also accompanied by a flashing red WARNING

Softkey label, as shown in Figure 12-2. Pressing the WARNING Softkey acknowledges the presence of the warning alert, and stops the aural tone (if applicable). The softkey has now reverted to the

ALERTS Softkey label and displays a description of the warning annunciation in the Alerts Window when pressed.

• CAUTION: This level of alert indicates the existence of abnormal conditions on the aircraft that may require pilot intervention. A caution annunciation is displayed in the Annunciation

Window as yellow text. A caution annunciation is also accompanied by a flashing yellow WARNING

Softkey label, as shown in Figure 12-3. Pressing the

CAUTION Softkey acknowledges the presence of the caution alert. The softkey has now reverted to the ALERTS Softkey label and displays a description of the caution annunciation in the Alerts Window when pressed.

• ADVISORY ANNUNCIATION: This level of alert provides general information to the pilot that may not need immediate attention. An advisory annunciation is displayed in the Annunciation

Window as white text. An advisory annunciation is also accompanied by a flashing white ADVISORY

Softkey label, as shown in Figure 12-4. Pressing the

ADVISORY Softkey acknowledges the presence of the advisory alert. The softkey has now reverted to the ALERTS Softkey label and displays a description of the advisory annunciation in the Alerts Window when pressed.

• ALERT MESSAGE: These messages are provided to make the pilot aware of G1000 system problems or status, and may not require pilot action. An alert message is accompanied by a flashing white

ADVISORY Softkey label, as shown in Figure 12-

4. Pressing the ADVISORY Softkey acknowledges the presence of the advisory alert, The softkey has now reverted to the ALERTS Softkey label and displays a description of the alert message in the

Alerts Window when pressed.

Figure 12-2 WARNING Softkey

Annunciation

Figure 12-3 CAUTION Softkey

Annunciation

Figure 12-4 ADVISORY Softkey

Annunciation

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

12.2 A36/G36 AIRCRAFT ANNUNCIATIONS

& ALERTS

The following alert annunciations are configured specifically for the Beechcraft A36/G36 aircraft. See the

Beechcraft A36/G36 Pilot’s Operating Handbook (POH) for information regarding pilot responses.

WARNING Annunciation

Annunciation Window Text

GEAR UP

Alerts Window Message

Gear up.

ALT 1 INOP

ALT 2 INOP

ALT 1-2 INOP

CAUTION Annunciation

Annunciation Window Text

AC DOOR EXTD

STARTER ENGD

BUS1 VOLT HI

BUS2 VOLT HI

AFT DOOR

ADVISORY Annunciation

Alternator 1 offline.

Alternator 2 offline.

Alternators 1 and 2 offline.

Alerts Window Message

Air conditioner on and door extended.

Starter relay has power applied.

Bus 1 voltage greater than 30 VDC.

Bus 2 voltage greater than 30 VDC.

Aft door not latched.

Annunciation Window Text

BUSES TIED

Alert Message

Alerts Window Message

Bus 2 is tied to Bus 1.

Alerts Window Message

PFD FAN FAIL – The cooling fan for the PFD is inoperative.

MFD FAN FAIL – The cooling fan for the MFD is inoperative.

AVIONICS FAN – The cooling fan for remote avionics is inoperative.

Audio Alert

Continuous Tone (received through the G1000 audio from another source)

Repeating Tone

Repeating Tone

Repeating Tone

Audio Alert

Single Chime

Single Chime

Single Chime

Single Chime

Single Chime

Audio Alert

None

Audio Alert

None

None

None

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-3

SECTION 12 – ANNUNCIATIONS

& ALERTS

12-4

12.3 AFCS ALERTS

System Status Field

The following AFCS alert annunciations appear in the

AFCS System Status field on the PFD.

• WARNING: Red annunciation is time critical and indicates an abnormal AFCS condition requiring immediate pilot attention.

• CAUTION: Yellow annunciation indicates the existence of abnormal AFCS conditions that may require pilot intervention.

Condition

Pitch Failure

System Status Field

Figure 12-5 AFCS System Status Field

Annunciation Description

Pitch axis control failure. AP is inoperative.

Roll Failure

MET Switch Stuck, or

Pitch Trim Axis Control

Failure

Yaw Damper Failure

System Failure

Elevator Mistrim Up

Elevator Mistrim Down

Aileron Mistrim Left

Aileron Mistrim Right

Rudder Mistrim Left

Rudder Mistrim Right

Preflight Test

Roll axis control failure. AP is inoperative.

If annunciated when AP is engaged, take control of the aircraft and disengage the autopilot. If annunciated when AP is not engaged, move each half of the MET switch separately to check if a stuck switch is causing the annunciation.

Yaw Damper control failure.

AP and MET are unavailable. FD may still be available.

A condition has developed causing the pitch servo to provide a sustained force. Be prepared to apply nose up control wheel force upon autopilot disconnect.

A condition has developed causing the pitch servo to provide a sustained force. Be prepared to apply nose down control wheel force upon autopilot disconnect.

A condition has developed causing the roll servo to provide a sustained left force. Ensure the slip/skid indicator is centered and observe any maximum fuel imbalance limits.

A condition has developed causing the roll servo to provide a sustained right force. Ensure the slip/skid indicator is centered and observe any maximum fuel imbalance limits.

A condition has developed causing the yaw servo to provide a sustained force. Ensure the slip/skid indicator is centered and observe any maximum fuel imbalance limits.

A condition has developed causing the yaw servo to provide a sustained force. Ensure the slip/skid indicator is centered and observe any maximum fuel imbalance limits.

Performing preflight system test. Upon completion, the aural alert will be heard.

Preflight system test has failed.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

12.4 TAWS ALERTS

Annunciations appear on the PFD and MFD. Pop-up alerts appear only on the MFD.

Alert Type

PFD/MFD TAWS

Page

Annunciation

MFD

Pop-Up Alert

Excessive Descent Rate Warning (EDR)

Reduced Required Terrain Clearance Warning (RTC)

Imminent Terrain Impact Warning (ITI)

Reduced Required Obstacle Clearance

Warning (ROC)

Imminent Obstacle Impact Warning (IOI)

Reduced Required Terrain Clearance Caution

(RTC)

Imminent Terrain Impact Caution (ITI)

Reduced Required Obstacle Clearance

Caution (ROC)

Imminent Obstacle Impact Caution (IOI)

Premature Descent Alert Caution (PDA)

Altitude Callout “500”

Excessive Descent Rate Caution (EDR)

Negative Climb Rate Caution (NCR)

None or or or or or or or or

None or

Aural Message

“Pull Up”

“Terrain, Terrain; Pull Up, Pull Up” or

“Terrain Ahead, Pull Up; Terrain Ahead, Pull Up”

Terrain Ahead, Pull Up; Terrain Ahead, Pull Up” or

“Terrain, Terrain; Pull Up, Pull Up”

“Obstacle, Obstacle; Pull Up, Pull Up” or

“Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up”

“Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up” or

“Obstacle, Obstacle; Pull Up, Pull Up”

“Caution, Terrain; Caution, Terrain” or

“Terrain Ahead; Terrain Ahead”

“Terrain Ahead; Terrain Ahead” or

“Caution, Terrain; Caution, Terrain”

“Caution, Obstacle; Caution, Obstacle” or

“Obstacle Ahead; Obstacle Ahead”

“Obstacle Ahead; Obstacle Ahead” or

“Caution, Obstacle; Caution, Obstacle”

“Too Low, Terrain”

“Five-Hundred”

“Sink Rate”

“Don’t Sink” or

“Too Low, Terrain”

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-5

SECTION 12 – ANNUNCIATIONS

& ALERTS

TAWS System Status Annunciations

Alert Type

TAWS System Test Fail

TAWS Alerting is disabled

No GPS position or excessively degraded

GPS signal

System Test in progress

System Test pass

PFD/MFD TAWS

Page

Annunciation

None

MFD

Pop-Up Alert

None

None

None

Aural Message

“TAWS System Failure”

None

“TAWS Not Available”

“TAWS Availble” will be heard when sufficient

GPS signal is re-established.

None

“TAWS System Test OK”

None

None

12.5 TRAFFIC VOICE ALERTS

Voice Alert

“Traffic”

Alert Trigger

Played when a Traffic Advisory (TA) is issued.

“Traffic Not Available” Played when the traffic system fails or cannot communicate.

“Traffic, Traffic” Played when a Traffic Advisory (TA) is issued (Skywatch TAS system).

“Traffic Advisory System Test Passed” Played when the TAS system passes a pilot-initiated self test.

“Traffic Advisory System Test Failed” Played when the TAS system fails a pilot-initiated self test.

12.6 G1000 SYSTEM ANNUNCIATIONS

When an LRU or an LRU function fails, a large red

‘X’ is typically displayed on windows associated with the failed data. The following section describes various system annunciations. Refer to the POH for additional information regarding pilot responses to these annunciations.

NOTE: Upon power-up of the G1000 system, certain windows remain invalid as G1000 equipment begins to initialize. All windows should be operational within one minute of power-up. Should any window continue to remain flagged, the G1000 system should be serviced by a Garmin-authorized repair facility.

12-6

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

System Annunciation

SECTION 12 – ANNUNCIATIONS

& ALERTS

Comment

Attitude and Heading Reference System is aligning.

Display system is not receiving attitude information from the AHRS.

Display system is not receiving airspeed input from air data computer.

Display is not receiving altitude input from the air data computer.

Display is not receiving vertical speed input from the air data computer.

Display is not receiving valid heading input from AHRS.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-7

SECTION 12 – ANNUNCIATIONS

& ALERTS

Display is not receiving altitude input from the air data computer.

Display is not receiving vertical speed input from the air data computer.

Other Various Red X Indications

Display is not receiving valid heading input from AHRS.

GPS information is either not present or is invalid for navigation use.

Note that AHRS utilizes GPS inputs during normal operation. AHRS operation may be degraded if GPS signals are not present (see POH).

Display is not receiving valid transponder information.

A red ‘X’ through any other display field, such as engine instrumentation fields, indicates that the field is not receiving valid data.

12-8

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

A red ‘X’ may be the result of an LRU or an LRU function failure. The Figure 12-6 illustrates all possible flags and the responsible LRUs.

GIA 63 Integrated

Avionics Units

GIA 63 Integrated

Avionics Units

GDC 74A Air Data

Computer

GEA 71 Engine

Airframe Unit

OR

GIA 63 Integrated

Avionics Unit

GRS 77 AHRS

OR

GMU 44

Magnetometer

GIA 63 Integrated

Avionics Units

GDC 74A Air Data

Computer

Figure 12-6 G1000 System Failure Annunciations

GTX 33 Transponder

OR

GIA 63 Integrated

Avionics Units

12.7 G1000 SYSTEM ALERT MESSAGES

This section describes various G1000 system alert messages. Certain messages are issued due to an LRU or an LRU function failure. Such messages are displayed in the Alerts Window and are normally accompanied by a corresponding red ‘X’ annunciation as shown previously in the G1000 System Annunciation section.

NOTE: This section provides information regarding G1000 alert messages that may be displayed by the system. Knowledge of the aircraft, systems, flight conditions, and other existing operational priorities must be considered when responding to a message. Always use sound pilot judgment. The Beechcraft A36/

G36 Pilot’s Operating Handbook (POH) takes precedence over any conflicting guidance found in this section.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-9

SECTION 12 – ANNUNCIATIONS

& ALERTS

MFD & PFD Message Advisories

Message

DATA LOST – Pilot stored data was lost. Recheck settings.

XTALK ERROR – A flight display crosstalk error has occurred.

PFD1 SERVICE – PFD1 needs service.

Return unit for repair.

MFD1 SERVICE – MFD1 needs service. Return unit for repair.

PFD1 CONFIG – PFD1 configuration error. Config service req’d.

Comments

The pilot profile data was lost. System reverts to default pilot profile and settings.

The pilot may reconfigure the MFD & PFD with preferred settings, if desired.

The MFD and PFD are not communicating with each other. The G1000 system should be serviced.

The PFD and/or MFD self-test has detected a problem. The G1000 system should be serviced.

MFD1 CONFIG – MFD1 configuration error. Config service req’d.

SW MISMATCH – GDU software mismatch. Xtalk is off.

MANIFEST – PFD1 software mismatch.

Communication halted.

MANIFEST – MFD1 software mismatch. Communication halted.

PFD1 COOLING – PFD1 has poor cooling. Reducing power usage.

MFD1 COOLING – MFD1 has poor cooling. Reducing power usage.

The PFD and/or MFD configuration settings do not match backup configuration memory. The G1000 system should be serviced.

The MFD and PFD have different software versions installed. The G1000 system should be serviced.

The PFD and/or MFD has incorrect software installed. The G1000 system should be serviced.

The PFD and/or MFD is overheating and is reducing power consumption by dimming the display. If problem persists, the G1000 system should be serviced.

PFD1 “KEY” KEYSTK – Key is stuck.

A key is stuck on the PFD and/or MFD bezel. Attempt to free the stuck key by press-

MFD1 “KEY” KEYSTK – Key is stuck.

ing it several times. The G1000 system should be serviced if the problem persists.

CNFG MODULE – PFD1 configuration module is inoperative.

PFD1 VOLTAGE – PFD1 has low voltage. Reducing power usage.

The PFD configuration module backup memory has failed. The G1000 system should be serviced.

The PFD1 voltage is low. The G1000 system should be serviced.

MFD1 VOLTAGE – MFD1 has low voltage. Reducing power usage.

The MFD1 voltage is low. The G1000 system should be serviced.

12-10

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

Database Message Advisories

Alerts Window Message

MFD1 DB ERR – MFD1 aviation database error exists.

PFD1 DB ERR – PFD1 aviation database error exists.

MFD1 DB ERR – MFD1 basemap database error exists.

PFD1 DB ERR – PFD1 basemap database error exists.

MFD1 DB ERR – MFD1 terrain database error exists.

PFD1 DB ERR – PFD1 terrain database error exists.

MFD1 DB ERR – MFD1 obstacle database error exists.

PFD1 DB ERR – PFD1 obstacle database error exists.

MFD1 DB ERR – MFD1 airport terrain database error exists.

PFD1 DB ERR – PFD1 airport terrain database error exists.

DB MISMATCH – Aviation database version mismatch. Xtalk is off.

DB MISMATCH – Aviation database type mismatch. Xtalk is off.

DB MISMATCH – Basemap database version mismatch. Xtalk is off.

DB MISMATCH – Terrain database version mismatch. Xtalk is off.

DB MISMATCH – Terrain database type mismatch. Xtalk is off.

DB MISMATCH – Obstacle database version mismatch. Xtalk is off

Comments

The MFD and/or PFD detected a failure in the aviation database. Attempt to reload the aviation database. If problem persists, the G1000 system should be serviced.

The MFD and/or PFD detected a failure in the basemap database.

The MFD and/or PFD detected a failure in the terrain database. Ensure that the terrain card is properly inserted in display. Replace terrain card. If problem persists, The

G1000 system should be serviced.

The MFD and/or PFD detected a failure in the obstacle database. Ensure that the data card is properly inserted. Replace data card. If problem persists, The G1000 system should be serviced.

The MFD and/or PFD detected a failure in the airport terrain database. Ensure that the data card is properly inserted. Replace data card. If problem persists, The G1000 system should be serviced.

The PFD and MFD have different aviation database versions installed. Crossfill is off.

Install correct aviation database version in both displays.

The PFD and MFD have different aviation database types installed (Americas, European, etc.). Crossfill is off. Install correct aviation database type in both displays.

The PFD and MFD have different basemap database versions installed. Crossfill is off. Install correct basemap database version in both displays.

The PFD and MFD have different terrain database versions installed. Crossfill is off.

Install correct terrain database version in both displays.

The PFD and MFD have different terrain database types installed. Crossfill is off.

Install correct terrain database type in both displays.

The PFD and MFD have different obstacle database versions installed. Crossfill is off.

Install correct obstacle database version in both displays.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-11

SECTION 12 – ANNUNCIATIONS

& ALERTS

Database Message Advisories (Cont.)

Alerts Window Message

DB MISMATCH – Airport Terrain database mismatch. Xtalk is off

GMA 1347 Message Advisories

Comments

The PFD and MFD have different airport terrrain databases installed. Crossfill is off.

Install correct airport terrain database in both displays.

Alerts Window Message

GMA1 FAIL – GMA1 is inoperative.

GMA1 CONFIG – GMA1 configuration error. Config service req’d.

MANIFEST – GMA1 software mismatch. Communication halted.

GMA1 SERVICE – GMA1 needs service. Return unit for repair.

BACKUP PATH – Audio panel 1 using backup data path.

Comments

The audio panel self-test has detected a failure. The audio panel is unavailable. The

G1000 system should be serviced.

The audio panel configuration settings do not match backup configuration memory.

The G1000 system should be serviced.

The audio panel has incorrect software installed. The G1000 system should be serviced.

The audio panel self-test has detected a problem in the unit. Certain audio functions may still be available, and the audio panel may still be usable. The G1000 system should be serviced when possible.

The #1 audio panel is using a backup communication path. The G1000 system should be serviced when possible.

GIA 63 Message Advisories

Alerts Window Message

GIA1 CONFIG – GIA1 configuration error. Config service req’d.

GIA2 CONFIG – GIA2 configuration error. Config service req’d.

GIA1 COOLING – GIA1 temperature too low.

GIA2 COOLING – GIA2 temperature too low.

GIA1 COOLING – GIA1 over temperature.

GIA2 COOLING – GIA2 over temperature.

Comments

The GIA1 and/or GIA2 configuration settings do not match backup configuration memory. The G1000 system should be serviced.

The GIA1 and/or GIA2 temperature is too low to operate correctly. Allow units to warm up to operating temperature.

The GIA1 and/or GIA2 temperature is too high. If problem persists, the G1000 system should be serviced.

12-12

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

GIA 63 Message Advisories (Cont.)

Alerts Window Message

GIA1 SERVICE – GIA1 needs service.

Return the unit for repair.

GIA2 SERVICE – GIA2 needs service.

Return the unit for repair.

HW MISMATCH – GIA hardware mismatch. Communication halted.

MANIFEST – GIA1 software mismatch.

Communication halted.

MANIFEST – GIA2 software mismatch.

Communication halted.

COM1 TEMP – COM1 over temp.

Reducing transmitter power.

COM2 TEMP – COM2 over temp.

Reducing transmitter power.

COM1 SERVICE – COM1 needs service. Return unit for repair.

COM2 SERVICE – COM2 needs service. Return unit for repair.

COM1 PTT – COM1 push-to-talk key is stuck.

COM2 PTT – COM2 push-to-talk key is stuck.

COM1 RMT XFR – COM1 remote transfer key is stuck.

COM2 RMT XFR – COM2 remote transfer key is stuck.

RAIM UNAVAIL – RAIM is not available from FAF to MAP waypoints.

RAIM UNAVAIL – RAIM is not available.

POSN ERROR – RAIM has determined

GPS position is in error.

Comments

The GIA1 and/or GIA2 self-test has detected a problem in the unit. The G1000 system should be serviced.

There is a hardware mismatch between GIA1 and GIA2. The G1000 system should be serviced.

The GIA1 and/or GIA 2 has incorrect software installed. The G1000 system should be serviced.

The system has detected an over temperature condition in COM1 and/or COM2. The transmitter will operate at reduced power. If the problem persists, the G1000 system should be serviced.

The system has detected a failure in COM1 and/or COM2. COM1 and/or COM2 may still be usable. The G1000 system should be serviced when possible.

The COM1 and/or COM2 external push-to-talk switch is stuck in the enable (or

“pressed”) position. Press the PTT switch again to cycle its operation.

If the problem persists, the G1000 system should be serviced.

The COM1 and/or COM2 transfer switch is stuck in the enabled (or “pressed”) position. Press the transfer switch again to cycle its operation. If the problem persists, the G1000 system should be serviced.

GPS satellite coverage is insufficient to perform Receiver Autonomous Integrity

Monitoring (RAIM) from the FAF to the MAP waypoints.

GPS satellite coverage is insufficient to perform Receiver Autonomous Integrity

Monitoring (RAIM) for the current phase of flight.

When a RAIM position error is detected, GPS is flagged and the system no longer provides GPS-based guidance.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-13

SECTION 12 – ANNUNCIATIONS

& ALERTS

12-14

GIA 63 Message Advisories (Cont.)

Alerts Window Message

DGRD GPS ACC – GPS position accuracy degraded & RAIM unavailable.

GPS1 FAIL – GPS1 is inoperative.

GPS2 FAIL – GPS2 is inoperative.

GPS1 SERVICE – GPS1 needs service.

Return unit for repair.

GPS2 SERVICE – GPS2 needs service.

Return unit for repair.

NAV1 SERVICE – NAV1 needs service.

Return unit for repair.

NAV2 SERVICE – NAV2 needs service.

Return unit for repair.

NAV1 RMT XFR – NAV1 remote transfer key is stuck.

NAV2 RMT XFR – NAV2 remote transfer key is stuck.

G/S1 FAIL – G/S1 is inoperative.

G/S2 FAIL – G/S2 is inoperative.

G/S1 SERVICE – G/S1 needs service.

Return unit for repair.

G/S2 SERVICE – G/S2 needs service.

Return unit for repair.

Comments

GPS position accuracy has been degraded and RAIM is not available.

A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver is unavailable. The G1000 system should be serviced.

A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver may still be available. The G1000 system should be serviced.

A failure has been detected in the NAV1 and/or NAV2 receiver. The receiver may still be available. The G1000 system should be serviced.

The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”) state. Press the transfer switch again to cycle its operation. If the problem persists, the G1000 system should be serviced.

A failure has been detected in glideslope receiver 1 and/or receiver 2. The G1000 system should be serviced.

A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver may still be available. The G1000 system should be serviced when possible.

GEA 71 Message Advisories

Alerts Window Message

GEA1 CONFIG – GEA1 configuration error. Config service req’d.

MANIFEST – GEA1 software mismatch. Communication halted.

BACKUP PATH – EIS using backup data path.

Comments

The GEA 71 configuration settings do not match those of backup configuration memory. The G1000 system should be serviced.

The GEA 71 has incorrect software installed. The G1000 system should be serviced.

The GEA 71 is using a backup communication path. The G1000 system should be serviced when possible.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

GTX 33 Message Advisories

Alerts Window Message

XPDR1 CONFIG – XPDR1 config error.

Config service req’d.

MANIFEST – GTX1 software mismatch.

Communication halted.

BACKUP PATH – XPDR1 using backup data path.

Comments

The transponder configuration settings do not match those of backup configuration memory. The G1000 system should be serviced.

The transponder has incorrect software installed. The G1000 system should be serviced.

The #1 transponder is using a backup communications path. The G1000 system should be serviced when possible.

GRS 77 Message Advisories

Alerts Window Message

AHRS1 TAS – AHRS1 not receiving airspeed.

AHRS1 GPS – AHRS1 using backup

GPS source.

AHRS1 GPS – AHRS1 not receiving any GPS information.

AHRS1 GPS – AHRS1 not receiving backup GPS information.

AHRS1 GPS – AHRS1 operating exclusively in no-GPS mode.

MANIFEST – GRS1 software mismatch.

Communication halted.

BACKUP PATH – AHRS1 using backup data path.

AHRS1 SRVC – AHRS1 Magnetic-field model needs update.

GEO LIMITS – AHRS1 too far North/

South, no magnetic compass.

Comments

The #1 AHRS is not receiving true airspeed from the air data computer. The AHRS relies on GPS information to augment the lack of airspeed. The G1000 system should be serviced.

The #1 AHRS is using the backup GPS path. Primary GPS path has failed. The G1000 system should be serviced when possible.

The #1 AHRS is not receiving any or any useful GPS information. Check AFMS limitations. The G1000 system should be serviced.

The #1 AHRS is not receiving backup GPS information. The G1000 system should be serviced.

The #1 AHRS is operating exclusively in no-GPS mode. The G1000 system should be serviced.

The AHRS has incorrect software installed. The G1000 system should be serviced.

The #1 AHRS is using a backup communications data path. The G1000 system should be serviced when possible.

The #1 AHRS earth magnetic field model is out of date. Update magnetic field model when practical.

The aircraft is outside geographical limits for approved AHRS operation. Heading is flagged as invalid.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-15

SECTION 12 – ANNUNCIATIONS

& ALERTS

GMU 44 Message Advisories

Alerts Window Message

HDG FAULT – AHRS1 magnetometer fault has occurred.

MANIFEST – GMU1 software mismatch. Communication halted.

GDL 69 Message Advisories

Alerts Window Message

GDL69 CONFIG – GDL 69 configuration error. Config service req’d.

GDL69 FAIL – GDL 69 has failed.

Comments

A fault has occurred in the GMU 44. Heading is flagged as invalid. The AHRS uses

GPS for backup mode operation. The G1000 system should be serviced.

The GMU 44 has incorrect software installed. The G1000 system should be serviced.

Comments

GDL 69 configuration settings do not match those of backup configuration memory.

The G1000 system should be serviced.

A failure has been detected in the GDL 69. The receiver is unavailable. The G1000 system should be serviced

GDC 74A Message Advisories

Alerts Window Message

GDC1 CONFIG – GDC1 configuration error. Config service req’d.

MANIFEST – GDC1 software mismatch. Communication halted.

BACKUP PATH – ADC1 using backup data path.

Comments

GDC 74A configuration settings do not match those of backup configuration memory. The G1000 system should be serviced.

The GDC 74A has incorrect software installed. The G1000 system should be serviced.

The GDC 74A is using a backup communications data path. The G1000 system should be serviced when possible.

12-16

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

SECTION 12 – ANNUNCIATIONS

& ALERTS

Miscellaneous Message Advisories

Alerts Window Message

FPL WPT LOCK – Flight plan waypoint is locked.

FPL WPT MOVE – Flight plan waypoint moved.

The system has detected that a waypoint coordinate has changed due to a new aviation database update. Verify that stored flight plans contain correct waypoint locations.

TIMER EXPIRD – Timer has expired.

The system notifies the pilot that the timer has expired.

DB CHANGE – Database changed.

Verify user modified procedures.

This occurs when a stored flight plan contains procedures that have been manually edited. This alert is issued only after an aviation database update. Verify that the user-modified procedures in stored flight plans are correct and up to date.

FPL TRUNC – Flight plan has been truncated.

This occurs when a newly installed aviation database eliminates an obsolete approach or arrival used by a stored flight plan. The obsolete procedure is removed from the flight plan. Update flight plan with current arrival or approach.

APPR VPROF – Approaching VNAV profile.

APPR TRG ALT – Approaching target altitude.

LOCKED FPL – Cannot navigate locked flight plan.

Comments

Upon power-up, the G1000 system detects that a stored flight plan waypoint is locked. This occurs when an aviation database update eliminates an obsolete waypoint. The flight plan cannot find the specified waypoint and flags this message. This can also occur with user waypoints in a flight plan that is deleted.

Remove the waypoint from the flight plan if it no longer exists in any database,

OR update the waypoint name/identifier to reflect the new information.

Aircraft is approaching VNAV profile. Prepare to climb or descend to meet VNAV profile.

Aircraft is approaching target altitude. Prepare to level aircraft.

This occurs when the pilot attempts to activate a stored flight plan that contains locked waypoint. Remove locked waypoint from flight plan. Update flight plan with current waypoint.

WPT ARRIVAL – Arriving at waypoint

-[xxxx]

STEEP TURN – Steep turn ahead.

INSIDE ARSPC – Inside airspace.

ARSPC AHEAD – Airspace ahead less than 10 minutes.

Arriving at waypoint [xxxx], where [xxxx] is the waypoint name.

A steep turn is 15 seconds ahead. Prepare to turn.

The aircraft is inside the airspace.

Special use airspace is ahead of aircraft. The aircraft will penetrate the airspace within 10 minutes.

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

12-17

SECTION 12 – ANNUNCIATIONS

& ALERTS

Miscellaneous Message Advisories (Cont.)

Alerts Window Message

ARSPC NEAR – Airspace near and ahead.

ARSPC NEAR – Airspace near – less than 2 nm.

LEG UNSMOOTH – Flight plan leg will not be smooth.

APPR INACTV – Approach is not active.

SLCT AUTOSEQ – Select auto sequence mode.

SLCT FREQ – Select appropriate frequency for approach.

SLCT NAV – Select NAV on CDI for approach.

NO WGS84 WPT – Non WGS 84 waypoint for navigation -[xxxx]

TRAFFIC FAIL – Traffic device has failed.

STRMSCP FAIL – Stormscope has failed.

BACKUP PATH – Stormscope using backup path.

Comments

Special use airspace is near and ahead of the aircraft position.

Special use airspace is within 2 nm of the aircraft position.

The approaching flight plan waypoints are too close to allow for smooth turns.

Prepare for steep turns ahead and expect noticeable course deviations.

The system notifies the pilot that the loaded approach is not active. Activate approach when required.

The system notifies the pilot to select auto-sequence mode. Press the OBS Softkey to deactivate the OBS mode.

The system notifies the pilot to load the approach frequency for the appropriate NAV receiver. Select the correct frequency for the approach.

The system notifies the pilot to set the CDI to the correct NAV receiver. Set the CDI to the correct NAV receiver.

The selected waypoint [xxxx] does not use the WGS 84 datum. Cross-check position with alternate navigation sources.

The G1000 is no longer receiving data from the traffic system. The traffic device should be serviced.

Stormscope has failed. The G1000 system should be serviced.

Stormscope is using the backup communication path. The G1000 system should be serviced when possible.

12-18

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

INDEX

A

Abnormal COM operation 11-2

Activate a flight plan 8-3

Active flight plan 8-2

Advisory 12-1, 12-2

AFCS 1-3, 6-1, 6-2, 6-4, 6-6, 6-7, 6-9,

6-11, 6-12, 6-13, 12-4

Age 10-6

AHRS 12-15

Aircraft alerts 12-3

AIRMET 10-5

Airport frequency 7-6

Airport information 7-3

Airspace alerts 7-9

Airspeed indicator 2-3

Airspeed trend vector 2-3

Alerting System 12-1

Alerts 12-1

Alert levels 12-2

Alert Message 12-2

Alert message 12-1

Alert Pop-Up 10-14

Altitude hold 1-4, 6-4 – 6-8, 6-10

Altitude trend vector 2-4

ALT knob 1-4

Annunciations 12-1

AP 1-4, 6-1 – 6-7, 6-9, 12-4

Approaches 9-2

Approach activation 4-4

Approach markers

Signal augmentation 5-2

Approach Mode 6-12

AP disconnect 6-1

Arrivals 9-1

ASSIST 3-1

Attitude indicator 2-3

Audio alerting system 12-2

Audio panel 4-3, 5-1

Audio panel controls

DME 5-2

NAV1 5-2

NAV2 5-2

Auto-tuning 4-3, 4-4

Automatic squelch 4-3

Autopilot 6-1 – 6-10, 6-12, 6-13, 12-4

Aviation database 1-9

B

Backcourse 6-11

Barometric setting 2-4

Base reflectivity 10-4

BKSP softkey 4-4

BRG1 2-7

BRG2 2-7

C

Caution 12-1, 12-2

CDI 2-7, 12-18

Cell 10-2

Cell mode 10-2

Cell movement 10-5

Cloud tops 10-4

CLR key 1-3

Coast mode 10-7

Codes (important) 4-5

Code selection 4-4

CODE softkey 4-4

COM Frequency Window 4-1

COM knob 4-3

Controls 1-2, 4-1

Control Wheel Steering 6-1, 6-3

Create a new flight plan 8-3, 8-4

Create a new user waypoint 8-1

CWS 6-1, 6-3 – 6-9

Cyclones 10-5

Cylinder select 3-1

CYL SLCT 3-1

D

Departures 9-1

Direct-to 7-1

DME 1-6

Dual CDU failure 11-2

E

Echo tops 10-4

Edit a flight plan 8-5

EDR 10-13

Emergency code 4-5

Engine display 3-1

ENGINE softkey 3-1

Excessive Descent Rate 10-13

F

FCC iv

FD 1-4

Five-Hundred Aural Alert 10-13

FLC 1-4, 6-4, 6-7

Flight director 6-1 – 6-4, 6-6 – 6-10

Flight ID 4-5

Flight level change 1-4, 6-4, 6-7, 6-11,

6-16

Flight Plan Catalog 9-1, 9-2

FLTA 10-12

Forward Looking Terrain Avoidance

10-12

FPL key 1-3

Freezing level 10-5

Frequency toggle key 1-3, 4-3

G

GA 6-1, 6-3, 6-4, 6-8, 6-9, 6-12

Glideslope 2-2, 2-5, 6-4, 6-8, 6-9,

6-12

GMA 1347 1-1

Go Around 6-1, 6-4, 6-8, 6-9, 6-12,

6-19

H

HDG key 6-10

Heading hold 6-9

Heading indication 2-6, 2-7

Heading Select 1-3, 1-4, 6-9, 6-10

Heading Select Mode 6-10

Headset(s) 5-2

Hijack code 4-5

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Index-1

INDEX

Index-2

Horizontal situation indicator 2-6

Hurricanes 10-5

I

ICAO 4-5

ID 4-3

IDENT function 4-5

Imminent Terrain Impact 10-12

Impact point 10-12

Inhibit 10-11

Inhibit TAWS 10-11

INTEG 2-8

Interrogations 4-4

IOI 10-12, 10-15, 12-5

ITI 10-12

K

Key(s) 1-4

L

Lighted obstacle 10-14

Lightning 1-4, 1-7, 10-2, 10-3, 10-4

Load approach 8-5

Load a VOR frequency 7-8

Load departure 8-4

Load the frequency for a controlling

agency 7-9

Load the nearest ARTCC frequency 7-9

Loss of communication code 4-5

M

Manual Electric Trim 6-1

MAP 7-1

Map panning 10-5

Marker beacon 2-5

Message advisories 12-10 – 12-18

MET 6-1, 6-3, 12-4

METAR 10-3, 10-5

MFD 1-1, 4-4

Military interceptor operations code

4-5

Missed Approach 6-19

MKR/MUTE 5-2, 5-4

Mode selection softkeys 4-4

Morse code identifier 4-3

N

Nav/Com controls 4-1

NAV1 5-2

NAV2 5-2

NAVAIDS iii

Navigation 7-1

Navigation Mode 6-11

Navigation status window 2-2

NAV Frequency Window 4-1

NCR 10-13

Nearest Airports Page 7-3, 7-5 – 7-9,

8-1

Nearest ARTCC & FSS frequencies 7-8

Negative Climb Rate After Takeoff

10-13

NEXRAD 1-4, 1-7, 10-3 – 10-6

O

OBS 2-8

Obstacles 10-9, 10-10, 10-14, 12-11,

12-12, 12-13

Operation 5-2

Optional

NAV radios 4-3

overspeed 6-2

P

Page group icon 1-8

PDA 10-12

PFD 1-1, 4-1, 4-4

PIT 6-3, 6-4 pitch axis modes 6-3, 6-4

Pitch hold 1-4, 6-1, 6-4, 6-8

Pitch Hold Mode 6-4

PLAY key 5-4

Premature Descent Alert 10-12

PROC key 1-3

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

R

Red pointer 2-3

Remove departure, arrival, or approach

8-5

Replies 4-4

Reversionary mode 11-1

Revision RR-1

ROC 10-12, 10-15, 12-5

Roll Axis Modes 6-2, 6-9

Roll Hold 6-9

RTC 10-12

RX indicator 4-3

R indication 4-4

S

Selected vertical speed 2-5

Severe thunderstorm 10-5

SIGMET 10-5

Slip/Skid indicator 2-3

Softkey function (MFD) 1-4, 1-7

Speed ranges 2-3

Squelch 5-3

Store Flight Plan 8-5

Stormscope lightning data 1-4, 1-7,

10-2, 10-3

Strike 10-2

Strike mode 10-2

System annunciations 12-1, 12-6

System message advisories 12-9

T

TA 10-7, 12-6

TAF 10-3

TAS 10-8, 10-9, 12-6, 12-15

TAWS 10-10 – 10-12, 10-14 – 10-16,

12-5, 12-6

TAWS-B 10-10

TAWS system test 10-12

Terrain 10-9, 10-10, 10-14, 10-16,

11-2, 12-11

Terrain proximity 10-9

TIS 10-7

Tornado 10-5

Traffic Advisory 10-7, 10-8, 10-9, 12-6

Traffic advisory 10-16

Traffic map page 10-7, 10-8, 10-9, 10-14

Transponder 4-4

Transponder Status bar 4-4

Tropical storms 10-5

TX 4-3

U

Unlighted obstacle 10-14

V

Vertical Deviation/Glideslope indicator 2-5

Vertical navigation profile 8-8

Vertical speed 1-4, 2-1, 2-5, 6-4, 6-6, 12-1

Vertical Speed Bug 2-5

Vertical Speed Mode 6-6

VFR code 4-5

VHF 4-1

Voice Alerts 12-6

Voice alerts 12-6

VOL/PUSH ID 4-2

VOL/PUSH SQ 4-2, 4-3

Volume/squelch 5-3

VS 1-4, 6-4, 6-6

Vspeeds 2-3

W

WARN 2-8

Warning 12-1, 12-2, 12-4

Weather data link page 10-4

Weather product symbol 10-5

Weather product symbols 10-6

Weather warnings 10-5

Wind direction 10-5

Wind speed 10-5

X

XM weather 10-4

XPDR softkey 4-4

Y

Yaw Damper 1-4, 6-2, 6-3, 12-4

Yaw damper 1-4, 6-2, 6-3, 12-4

YD 1-4

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

INDEX

Index-3

INDEX

Blank Page

Index-4

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Garmin G1000 Cockpit Reference Guide for the Beechcraft A36/G36

Garmin International, Inc.

1200 East 151st Street

Olathe, KS 66062, U.S.A. p: 913.397.8200 f: 913.397.8282

Garmin AT, Inc.

2345 Turner Road SE

Salem, OR 97302, U.S.A.

p: 503.391.3411 f: 503.364.2138

Garmin (Europe) Ltd

Liberty House, Bulls Copse Road

Hounsdown Business Park

Southampton, SO40 9RB, U.K.

p: 44/0870.8501241 f: 44/0870.8501251

Garmin Corporation

No. 68, Jangshu 2nd Road

Shijr, Taipei County, Taiwan p: 886/2.2642.9199 f: 886/2.2642.9099

www.garmin.com

190-00525-01 Rev. B

© 2005-2007 Garmin Ltd. or its subsidiaries

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals