MS-PoE Injector User Manual
GE
Security
MS-PoE Injector User
Manual
P/N 1069179-EN • REV 1.01 • ISS 21MAR10
Copyright
© 2010 GE Security, Inc.
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from GE Security, Inc.,
except where specifically permitted under US and international
copyright law.
Disclaimer
The information in this document is subject to change without notice.
GE Security, Inc. (“GE Security”) assumes no responsibility for
inaccuracies or omissions and specifically disclaims any liabilities,
losses, or risks, personal or otherwise, incurred as a consequence,
directly or indirectly, of the use or application of any of the contents
of this document. For the latest documentation, contact your local
supplier or visit us online at www.gesecurity.com.
This publication may contain examples of screen captures and
reports used in daily operations. Examples may include fictitious
names of individuals and companies. Any similarity to names and
addresses of actual businesses or persons is entirely coincidental.
Trademarks and
patents
GE and the GE monogram are trademarks of General Electric
Company.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Intended use
FCC compliance
Use this product only for the purpose it was designed for; refer to the
data sheet and user documentation for details. For the latest product
information, contact your local supplier or visit us online at
www.gesecurity.com.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
MS-PoE Injector User Manual
i
Regulatory
information
Manufacturer
N4131
GE Security, Inc.
HQ and regulatory responsibility:
GE Security, Inc., 8985 Town Center Parkway,
Bradenton, FL 34202, USA
EU authorized manufacturing representative:
GE Security B.V., Kelvinstraat 7,
6003 DH Weert, The Netherlands
European Union
directives
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information see our Web site: www.gesecurity.com.
For contact information see our Web site: www.gesecurity.eu.
ii
MS-PoE Injector User Manual
Content
Chapter 1 Overview 1
Introduction 2
Product Overview 3
Product Specifications 4
Physical Specifications 5
Chapter 2 Hardware Installation 7
Before Installation 7
Installing the MS-PoE 8
MS-PoE Injector User Manual
iii
Chapter 1
Overview
The GE Security MS-PoE is an IEEE 802.3af Power over Ethernet Injector that
provides 48VDC power over Ethernet cables (PoE).
Package Contents
Your MS-PoE injector carton should contain the following items:
•
The Power over Ethernet Injector x 1
•
User's Manual x 1
If any item is missing or damaged, please consult the dealer from whom you
purchased you MS-PoE injector module.
MS-PoE Injector User Manual
1
Chapter 1: Overview
Introduction
The GE Security MS-PoE IEEE 802.3af Power over Ethernet Injector inserts DC
Voltage into Cat.5 cable, allowing the cable between the Injector (MS-PoE)
and Splitter (SP-PoE) to transfer data and power simultaneously. The
maximum distance between the Injector (MS-PoE) and Splitter (SP-PoE) is 100
meters. With MS-PoE installed, it is combines the Ethernet digital data with
power over the twisted pair cables as an IEEE 802.3af Power over Ethernet
Injector. The IEEE 802.3af Power over Ethernet splitter can separate the
digital data and power into two outputs.
With IEEE 802.3af Power over Ethernet devices installed, the system
administrator only has to use a single RJ-45 Ethernet cable to carry both
power and data to each device.
Product Features
2
•
Complies with IEEE 802.3af Power over Ethernet, IEEE 802.3/802.3u
10/100Base-TX
•
Provide DC 48V power over RJ-45 Ethernet cable to device with
Ethernet port
•
LED indicators power input indication
•
Distance up to 100 meters
•
Auto-detect of PoE IEEE 802.3af equipment, protects devices from
being damaged by an incorrect installation
•
Work with EIA568, category 5,4-pair cables for 10Base-T or
100Base-TX
•
EMI standards comply with FCC, CE class B
•
Saves time and reduces installation costs
•
Easy plug-and-play installation.
MS-PoE Injector User Manual
Chapter 1: Overview
Product Overview
Figure 1 shows the right and left side views of the MS-PoE injector.
Figure 1: MS-PoE right and left side panels
LED Indicators
LED
Color
Function
Power
Yellow
Lights to indicate that the MS-PoE has
power.
PoE ready / in-use
Green
Lights to indicate the port is providing
48VDC in-line power.
MS-PoE Injector User Manual
3
Chapter 1: Overview
Product Specifications
Model
MS-PoE
Interface
Ethernet Copper Port
1 x 10/100Base-TX for data in
RJ-45 connector
Ethernet + DC Copper Port
1 x 10/100Base-TX with IEEE
802.3af PoE PSE for data + DC out
RJ-45 connector
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet
/ PSE
PoE Power Supply Type
Mid-Span / Type B
Power PIN Assignment
4/5(+), 7/8(-)
PoE Power Output
PoE 48V DC, Max. 15.4 watts,
350mA
Number of device can be powered
1
Hardware Specification
Ethernet Data rate
10/100Mbps( vary on Ethernet
device attached)
Throughput(Packet per second)
148810@64Bytes
Input Power
48V DC, 0.38A max.
LED indicator
1 x Power
1 x PoE ready / in-use
Installation
Standalone or wall mount
Material
Plastic
Standard Conformance
IEEE 802.3 Ethernet
Standard Compliance
IEEE 802.3u Fast Ethernet
IEEE 802.3af Power over Ethernet
Ethernet cable
4
TIA/EIA-568, Category 5/5e cable
MS-PoE Injector User Manual
Chapter 1: Overview
Physical Specifications
Dimensions (W × D × H):
2.87” x 2.17” x 0.94” / 73 x 55 x 24mm
Weight:
0.22 lbs / 50g
Environmental Specification
Operating:
Temperature:
0°C ~ 50°C
Relative Humidity:
5% ~ 90% (non-condensing)
Storage:
Temperature:
-20°C ~ 70°C
Relative Humidity:
5% ~ 90% (non-condensing)
Electrical Specification
Input Voltage:
DC 48V, 0.38A
NOTE: This product is intended to be supplied by a UL Listed Direct Plug-In
Power Unit marked "Class 2" or "LPS" and output rated 48 VDC.
MS-PoE Injector User Manual
5
Chapter 1: Overview
6
MS-PoE Injector User Manual
Chapter 2
Hardware
Installation
This product provides two different running speeds - 10Mbps, 100Mbps in
the same device and automatically distinguishes the speed of the incoming
connection.
This section describes the hardware installation of MS-PoE. Before
connecting any network device to the MS-PoE, read this section carefully.
Before Installation
Before your installation, it is recommended that you check your network
environment. If there are any IEEE 802.3af devices that you need to power,
the MS-PoE can provide you a way to supply power for this Ethernet device
conveniently and easily. The MS-PoE works with an AC-DC adapter (not
supplied) with DC 48V input and injects this DC power into the pin of the
twisted pair cable (pair 4, 5 and pair 7, 8 for Fast Ethernet).
If it is very difficult to find a power socket for an AC-DC Adapter of your non
IEEE 802.3af networked device, the MS-PoE and SP-POE can provide you a
way to supply DC power for this Ethernet device conveniently and easily.
MS-PoE Injector User Manual
7
Chapter 2: Hardware Installation
Note: The MS-PoE and SP-POE can be installed in pair. However, the use of
third-party device is allowed if the device complied with IEEE 802.3af
standard.
Installing the MS-PoE
1.
Connect a standard network cable from Switch/workstation to
"Ethernet" port of MS-PoE.
2.
Connect the long cable that will be used to connect to the remote device
to the port "Ethernet + DC".
3.
Connect an AC adapter to "DC 48V" of MS-PoE. The power LED will be
steady on.
NOTE: This product is intended to be supplied by a UL Listed Direct Plug-In
Power Unit marked "Class 2" or "LPS" and output rated 48 VDC.
4.
8
Connect with IEEE 802.3af devices, due to the capability of IEEE 802.3af
standard, the MS-PoE can directly connect with any IEEE 802.3af endnodes like wireless access point, VoIP phones and Internet camera
where support IEEE 802.3af In-line Power over Ethernet port.
MS-PoE Injector User Manual
Chapter 2: Hardware Installation
Figure 2: Connection to the IEEE 802.3af device
Once MS-PoE detects the existence of an IEEE 802.3af device, the LED
indicator will stay steady, ON to show it is providing power.
Note: If the connected device is not fully complying with IEEE 802.3af
standard or in-line power device, the LED indicator of MS-PoE will not be
steady on.
Installing an MS-PoE and a SP-POE, Injector and
Splitter
1.
Connect a standard network cable from "Ethernet+DC" of MS-PoE to
"Ethernet+DC" of SP-POE. The POE LED of MS-PoE / SP-POE will light on
continuance.
2.
Connect the UTP cable in the package from "Ethernet" of SP-POE to the
RJ-45 port of remote device.
3.
Connect proper DC plug from "DC OUT" of SP-POE to remote device.
4.
Power on the remote device and the LED indicator on SP-POE will
remains on.
MS-PoE Injector User Manual
9
Chapter 2: Hardware Installation
Figure 3: Connection architecture over MS-PoE / SP-POE
Note: According to IEEE 802.3af standard, the MS-PoE will not inject power to
the cable if not connecting to IEEE 802.3af devices.
Please ensure the output voltage is correct before applying power to remote
device.
10
MS-PoE Injector User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising