Warranty
LG CodePlus PIVD100R Warranty
Broadcast Products
Welcome to the LG family! We believe that you will be pleased with your new PIVD100R Pro:Idiom
Video Distribution Transcoder System. Please read this warranty carefully, it is a “LIMITED
WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you
may also have other rights that vary from state-to-state within the U.S.A.
LG’s RESPONSIBILITY
Warranty Term
Parts
Warranty Service
Not Covered
One year parts and labor from date of purchase or delivery date.
New or remanufactured replacements for factory-defective parts may be used. Such replacement
parts are warranted for the remaining portion of the original warranty period.
Warranty service is provided at LG. Customer pays for shipping charges to LG; LG pays for return
shipping charges to return the PIVD100R to customer. Call 1-888-865-3026 for further information.
This warranty covers manufacturing defects and does not cover installation, adjustment of customer
controls, installation or repair of antenna systems, cable converters or cable company-supplied
equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other
causes beyond the control of LG. Any alteration of the product after manufacture voids this warranty
in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND LG SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL,
INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR
PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU.
CodePlus™ PIVD100R
Pro:Idiom® Video Distribution
Transcoder System
Installation & Setup
Quick Reference | Warranty
The latest product information and documentation is available online at:
www.LGsolutions.com/products
OWNER’S RESPONSIBILITY
Effective Warranty Date
Warranty begins on the date of delivery of the PIVD100R.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the
purchase date.
Installation Guide
Read the Installation & Setup Guide carefully so that you will understand the operation of the
PIVD100R and how to adjust the settings.
Warranty Service
For warranty service information, call 1-888-865-3026. Parts and service labor that are LG’s
responsibility (see above) will be provided without charge. Other service is at the owner’s expense.
If you have any problem in obtaining satisfactory warranty service, call 1-888-865-3026.
You must provide the model number, serial number and date of purchase or date of original installation.
For Customer Support/Service, please call:
1-888-865-3026
www.LGsolutions.com
CodePlus is a trademark of LG Electronics U.S.A., Inc. Pro:Idiom is a registered trademark of Zenith Electronics LLC. DIRECTV is a registered trademark of DIRECTV, Inc.
DISH, DISH Network, and ViP are registered trademarks of DISH Network LLC. All
other trademarks or registered trademarks are the property of their respective owners.
© Copyright 2012, LG Electronics U.S.A., Inc.
206-4203
Revision B
© Copyright 2012, LG Electronics U.S.A., Inc.
P/N: 206-4203 (Rev B)
For Customer Support/Service, please call:
Open Source Software Notice
1-888-865-3026
www.LGsolutions.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et de
plus qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user should be required to correct the interference at his own expense.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG
Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to
operate this product.
NOTE TO SATELLITE DISH INSTALLER:
This reminder is provided to call your attention to Articles 810 and 820 of the 2002
National Electrical Code. Refer to Article 810, in particular 810-1 and 810-15, for
required grounding of the metal dish antenna. Refer also to 810-2 which, by reference
to Article 820, requires that the satellite dish coaxial cable shield be connected to the
grounding system of the building as close to the point of cable entry as practical.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069, USA • Phone: 1-847-941-8000
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069
2
© Copyright 2012, LG Electronics U.S.A., Inc.
206-4203
The following GPL executables and LGPL libraries used in
this product are subject to the GPL Version 2.0/LGPL Version 2.1 License Agreements:
GPL EXECUTABLES: Linux kernel 2.6.33, LTIB 10.1.1,
bash-2.05b, busybox-1.1.3, e2fsprogs-1.34, ethtool-3,
gawk-3.1.3, lrzsz_0.12.21, lzo-2.03, mtd-utils-1.2.0,
net-tools-1.60, ntpclient_2003_194, openvpn-2.1.1,
pciutils-2.1.11, ppp-2.4.1, procps-3.1.11, screen-4.0.2-1,
skell-1.13, time-1.7
LGPL LIBRARIES: eglibc 2.8, libelf-0.8.5, termcap-2.0.8
To obtain the source code under GPL, LGPL, MPL and
other open source licenses that are contained in this product, please visit http://opensource.lge.com. In addition to
the source code, all referenced license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you
on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping and
handling) upon e-mail request to opensource@lge.com.
This offer is valid for three (3) years from the date on which
you purchased the product.
You can obtain a copy of the GPL, LGPL licenses from:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/oldlicenses/lgpl-2.1.html.
This product includes:
• OpenSSH-4.3p2:
Copyright © 1994, 1995 Tatu Ylonen, Espoo, Finland
Copyright © 1998 CORE SDI S.A., Buenos Aires,
Argentina
Copyright © 1995, 1996 by David Mazieres
Copyright © 1980, 1983, 1987, 1988, 1990, 1992, 1993,
1995 The Regents of the University of California
Copyright © 1999, 2000, 2001, 2002, 2003, 2004
Markus Friedl
Copyright © 1995, 1996, 1998, 1999 Theo de Raadt
Copyright © 1999, 2000, 2001, 2002 Niels Provos
Copyright © 1999 Dug Song
Copyright © 1999 Aaron Campbell
Copyright © 1999, 2000, 2001, 2002, 2003, 2004, 2005
Damien Miller
Copyright © 2001 Kevin Steves
Copyright © 2002 Daniel Kouril
Copyright © 2003 Wesley Griffin
Copyright © 2001 Per Allansson
Copyright © 2002, 2003 Nils Nordman
Copyright © 2001-2003 Simon Wilkinson
Copyright © 2000, 2001 2003 Ben Lindstrom
Copyright © 2002, 2005 Tim Rice
Copyright © 2000 Andre Lucas
Copyright © 2002 Chris Adams
Copyright © 2000, 2001 Corinna Vinschen
Copyright © 2002 Cray Inc. (Wendy Palm)
Copyright © 2000 Denis Parker
Copyright © 2001 Gert Doering
Copyright © 2001, 2003 Jakob Schlyter
206-4203
Copyright © 1996 Jason Downs
Copyright © 2002 Juha Yrjölä
Copyright © 2000 Michael Stone
Copyright © 2002 Networks Associates Technology, Inc.
Copyright © 1997, 1998, 2000-2002, 2004 Todd C.
Miller
Copyright © 2003, 2004, 2005 Darren Tucker
Copyright © 1988-2002 Sun Microsystems, Inc.
Copyright © 2005 The SCO Group
Copyright © 2004 The OpenBSD Project
Copyright © 2005 Anil Madhavapeddy
Copyright © 1994 Phil Karn
Copyright © 1996-1998, 2003 William Allen Simpson
Copyright © 2003 Peter Stuge
Copyright © 2005 Reyk Floeter
Copyright © 1991 Massachusetts Institute of Technology
Copyright © 2004 Ted Unangst and Todd Miller
Copyright © 1999 WIDE Project
Copyright © 1996 Internet Software Consortium
Portions Copyright © 1999-2001 Internet Software
Consortium
Portions Copyright © 1993 Digital Entertainment
Corporation
Portions Copyright © 1995 International Business
Machines, Inc.
• OpenSSL-1.0.0:
Copyright © 1998-2008 The OpenSSL Project
Copyright © 1995-1998 Eric Young
All rights reserved.
Permission is hereby granted, free of charge, to any
person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the
Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute,
sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do
so, subject to the following conditions:
SUBJECT TO THE TERMS OF THE GPL VERSION
2.0/LGPL VERSION 2.1 LICENSE AGREEMENTS,
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT
SHALL THE AUTHORS, COPYRIGHT HOLDERS, OR LG
ELECTRONICS (THE “LICENSOR”) BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH
THE SOFTWARE OR THE USE OR OTHER DEALINGS
IN THE SOFTWARE, EVEN IF LICENSOR HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
LICENSEE ASSUMES THE COST OF ALL NECESSARY
SERVICING, REPAIR, OR CORRECTION.
23
Specifications
Dimensions
Height:
Width:
Depth:
Weight:
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
1.692 inches (42.977 mm)
19.0 inches (482.6 mm) with mounting brackets attached
(for EIA standard 19-inch rack mount)
8.5 inches (215.9 mm)
4.45 pounds (2.02 kgrms) rack-only weight
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Environmental Storage Conditions
Temperature:
-20° to 70° Celsius
-4° to 158° Fahrenheit
Humidity:
95% non-condensing
8. Do not install near any heat sources,
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
Environmental Operating Conditions
Temperature (Tma):
0° to 40° Celsius
32° to 104° Fahrenheit
Humidity:
95% non-condensing
Electrical
RF Out Connector:
RF Output Span:
RF Output Frequency Range:
Active Output Level at RF Out jack:
Type ‘F’
4 Contiguous Channels (typically 24 MHz)
54 MHz to 864 MHz
+ 42 dBmV Min.
DC Input:
+12V DC @ 2.1 Amps
Ethernet Connector (Control Port):
Ethernet Connector (Feature Port):
10/100/1000BaseT, RJ-45
1000BaseT Full Duplex, RJ-45
X-Ports (8):
100BaseTX, RJ-45
USB Ports (2):
USB 2.0
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has
two blades and a third grounding prong.
The wide blade or the third prong are
provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked
on or pinched, particularly at plugs,
convenience receptacles, and the point
where it exits from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
in order to avoid injury from tip-over.
13. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
Note: Design and specifications subject to change without prior notice.
22
206-4203
206-4203
14. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply to your INSTALLATION,
consult your product dealer or local power
company.
15. Overloading
Do not overload wall power outlets and
extension cords as this can result in a risk of
fire or electric shock.
16. Disconnect Device
The AC mains plug is used as the disconnect
device. The disconnect device must remain
readily operable.
17. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Do not use liquid cleaners or aerosol cleaners.
18. Outdoor Use
Warning: To prevent fire or shock
hazards, do not expose this product
to rain or moisture.
19. Wet Location
Do not use this product near water or moisture or in an area, such as a basement, that
might become flooded. The apparatus shall
not be exposed to dripping or splashing and
no objects filled with liquids, such as vases,
shall be placed on the apparatus.
20. Test Equipment
In some cases, LG has supplied or recommended the use of test equipment and devices
for the setup and testing of the equipment. The
operation and maintenance of test equipment
is described in their associated instruction
manuals. Please refer to these manuals for
explicit instructions regarding the safe use and
handling of the equipment.
(Continued on next page)
3
Troubleshooting
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
21. Damage Requiring Service
Unplug this product from the wall power outlet and refer servicing to qualified service
personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore
the product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. If the product exhibits a distinct change in
performance.
Caution: Refer all servicing to qualified
service personnel.
22. Servicing
Caution: These servicing instructions are for use by qualified
service personnel only. To reduce
the risk of electrical shock, do not perform
any servicing other than that described in
the operating instructions unless you are
qualified to do so.
23. Replacement Parts
When replacement parts are required, be
sure the service technician uses replacement
parts specified by the manufacturer or that
have the same characteristics as the original
parts. Unauthorized substitutions may result
in fire, electric shock, or other hazards.
4
24. Safety Check
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
This section provides PIVD100R installation and setup troubleshooting information.
Equipment Setup Review
• Make sure all connectors and connections are tight and secure on all entertainment
system components.
PIVD100R Rack Installation
(also see pages 10 and 11)
• Check the PIVD100R LEDs:
− Under standard operating conditions the PWR (Power) LED on the PIVD100R front
To install the PIVD100R in a rack:
•
Carefully slide the PIVD100R into a standard
19-inch equipment rack.
•
When mounting in the rack, make sure to use
the appropriate hardware. ALL FOUR MOUNTING SCREWS MUST BE USED.
•
This equipment is not designed to support
other devices. Do NOT stack other equipment
on the top of the PIVD100R.
•
Rear cabling must be dressed and supported
so that the weight of the cabling is not a strain
on the PIVD100R connectors.
•
MOUNTING OF THE EQUIPMENT IN THE
RACK SHOULD BE SUCH THAT A HAZARDOUS CONDITION IS NOT ACHIEVED DUE
TO UNEVEN MECHANICAL LOADING.
Rack-mount Considerations
A. Elevated Operating Ambient
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature
of the rack environment may be greater than
room ambient. Therefore, consideration should
be given to installing the equipment in an
environment compatible with the maximum
ambient temperature (Tma) specified by the
manufacturer (see Specifications information
in this document).
panel is continuously lit green. If there is a hardware fault, the PWR LED will turn
and stay red. (When power is first applied to the PIVD100R, the PWR LED initially
flashes red and then turns green.)
− When the PIVD100R is booted and operating normally, the STATUS LED is
continuously lit green.
• COM 23 STBs: Ensure the satellite STB access card is installed, up-to-date, and
authorized by DIRECTV.
• ViP 222 and ViP 222k STBs: Ensure the satellite STB smart card is up-to-date and
authorized by DISH Network.
Network Setup
If the network is configured for DHCP but the PIVD100R has not been assigned an IP
address, i.e., the Ctrl IP field in the PIVD100R System Information display is blank:
1. Check the Control Port connector on the rear panel of the PIVD100R. Make sure
the cable connection is tight and secure.
2. Observe the green LED on the Control Port. Once the PIVD100R is connected to
the network, the LED will be lit continuously.
3. Contact the network administrator to verify the network status and check that the
DHCP server is working properly.
(Continued on next page)
206-4203
206-4203
21
System Setup (Cont.)
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
f)
(Continued from previous page)
(Dual tuner STB only) Repeat steps (c) to (e) to set the channel for the second
of the two tuners. When the channel has been set on both tuners, continue to
step (g).
g) At the STB Command > prompt, type stb and press Enter to access the STB
Menu for another STB.
At the Enter STB number [#]> prompt, type the number of the PIVD100R
X-Port connected to the next STB for which you wish to set the channel(s) and
press Enter. The system will identify the (newly) current STB and then display an
STB command prompt.
h) Repeat steps (c) to (g) to set the channel on each STB/tuner.
Note: After you set the channel for the last STB/tuner, you will not have to repeat
step (g).
19. At the STB Command > prompt, type exit and press Enter to return to the
Command > prompt.
20. (Optional) If you wish to review the system settings at this time, at the Command >
prompt, type info and press Enter to display the system information.
Note: You can also run the “monitor” command, if desired, to review the system
settings. Refer to the extended Installation & Setup Guide for further information on
monitoring the system.
B. Reduced Air Flow
Installation of the equipment in a rack should
be such that the amount of air flow required
for safe operation of the equipment is not
compromised. To ventilate the system normally and avoid overheating, leave at least
1 inch (2.5 cm) on each side (including top
and bottom) of the PIVD100R. Do NOT stack
other equipment on the top of the PIVD100R.
C. Circuit Overloading
Consideration should be given to the
connection of the equipment to the supply
circuit and the effect that overloading of the
circuits might have on overcurrent protection
and supply wiring.
D. Reliable Earthing
Maintain reliable earthing of rack-mounted
equipment. Particular attention should be
given to supply connections other than direct
connections to the branch circuit (e.g. use of
power strips).
E. Mains Outlet Earthing
The apparatus with Class I construction must
be connected to a mains socket outlet with a
protective earthing connection.
PIVD100R Installation on a Flat Surface
To install the PIVD100R on a level surface (table
top, shelf, etc.):
•
Install the equipment in an environment
compatible with the maximum operating
ambient temperature (Tma) specified by the
manufacturer (see Specifications information
in this document).
•
Place spacers or rubber feet (not provided) on
the bottom of the PIVD100R.
•
Carefully place the PIVD100R on the level
surface.
•
To ventilate the system normally and avoid
overheating, leave at least 1 inch (2.5 cm) on
each side (including top and bottom) of the
PIVD100R. Do NOT stack other equipment on
the top of the PIVD100R.
21. At the Command > prompt, type reset and press Enter to reset the system.
Note: This initiates a reset of the PIVD100R and may also initiate a reset of one or
more STBs, if required. Once the PIVD100R is reset (may take up to 90 seconds), it
may then take up to 10 minutes for the PIVD100R to reestablish communication with
the STBs. After the system reset, the PIVD100R resumes normal operation.
22. Check one or more room receivers to make sure all content is properly mapped
and available.
20
206-4203
206-4203
5
PIVD100R Product Description
System Setup (Cont.)
The LG CodePlus™ PIVD100R Pro:Idiom® Video Distribution Transcoder System
provides a flexible 8- to 16-program HDTV solution for system providers who provide
satellite delivered content to commercial facilities (hotels, hospitals, etc.). The PIVD100R
incorporates eight 100BaseTX X-Ports that connect up to eight satellite set-top boxes
(STBs) from either DIRECTV® or DISH Network® satellite service.
Features
• Two output options: RF or IP (concurrent operation not supported)
− RF output: The PIVD100R generates four contiguous 256-QAM cable channels,
with up to two DIRECTV or three DISH Network program streams multiplexed on
each channel. This capability provides up to 8 HD programs of DIRECTV content
or up to 12 HD programs of DISH Network content.
− IP output: The PIVD100R provides up to 8 HD programs of DIRECTV content or
up to 16 HD programs of DISH Network content.
•
•
•
•
b) At the Setup Command > prompt, type type and press Enter. The system
will display a list of the available STB types (DIRECTV or DISH), followed by a
prompt for the new STB type:
Enter number of new STB type [2]>
c) At the prompt, type the number that corresponds to the appropriate STB type
and press Enter.
The system will confirm your selection, for example:
STB type is set: Dish
Note: If you set a new STB type, you will be prompted to reset the system. If you
intend to modify additional configuration settings during the current session, you may
wait until all changes are complete before you reset the system.
Transcodes satellite content for distribution
17. If the Setup Command > prompt is on display, type exit and press Enter to
return to the Command > prompt.
Built-in Pro:Idiom content protection
18. Set the channel(s) on each of the installed STBs as follows:
Supports Pro:Idiom encryption key maintenance
a) At the Command > prompt, type stb and press Enter to access the STB Menu.
Transcoded output supports Closed Captions and V-Chip (Parental Control)
(if included in the signal source)
b) At the Enter STB number > prompt, type the number of the PIVD100R
X-Port connected to the STB for which you wish to set the channel(s). Then,
press Enter.
• Remote management capability over Ethernet via either graphical user interface
(GUI) or command line interface
•
•
•
•
(Continued from previous page)
The system will identify the current STB and then display an STB command
prompt, for example:
Current STB: STB-1
STB-1 Command >
Unit does not require local monitor, keyboard, or mouse connection
Small, lightweight chassis
19-inch rack-mountable
1U height profile to minimize rack space usage
c) At the STB Command > prompt, type channel and press Enter.
The PIVD100R converts satellite MPEG-4 HD programming to an encrypted, encoded
transport stream. A Pro:Idiom-compatible television is required to view premium HD
content, and a proper session ID must be set at the TV in order for Pro:Idiom
decryption to be enabled. LG’s Pay-Per-View (PPV) partners can set up this session
through their interface. LG’s Free-To-Guest (FTG) Mode of operation also enables
Pro:Idiom decryption.
d) (Dual tuner STB only) At the Enter tuner number (1 or 2) [1]> prompt,
either press Enter to accept the default value in square brackets, or type the
appropriate tuner number and then press Enter.
e) At the Enter channel [7]> prompt, either press Enter to accept the default
value in square brackets, or type in a new channel number and then press Enter.
The system will display confirmation, for example:
Multiple PIVD100R units may be combined in the head end to deliver an entire channel
lineup of HD programming.
Channel: 8
or
Tuner: 1 Channel: 2
(Continued on next page)
Note: Design and specifications subject to change without prior notice.
6
206-4203
206-4203
19
System Setup (Cont.)
Setup Information
(Continued from previous page)
14. (Optional) For remote management purposes, you can set a static IP address for
the PIVD100R Control Port as follows:
a) If the Command > prompt is on display, type setup and press Enter to access
the Setup Menu.
Check the following items before you begin PIVD100R installation and setup procedures.
b) At the Setup Command > prompt, type setip and press Enter. The system will
display the current network configuration, followed by the Network Configuration
Menu.
__ The satellite dish must be located where it will have unobstructed access to the
satellite signals. At least RG-6 or larger coaxial cables must be installed between
the satellite dish antenna system and the satellite STB. Refer to documentation
provided with the satellite dish antenna.
c) Use the Network Configuration Menu “ip” and “dns” commands and follow the
system prompts to configure the Control Port. Refer to the extended Installation
& Setup Guide for further information on the commands.
Note: Review the New Network Configuration overview carefully before you
confirm the Control Port configuration settings. Ensure that each of the addresses
was entered correctly.
Note: If you change the Control Port configuration, you will be prompted to reset the
system. If you intend to modify additional configuration settings during the current
session, you may wait until all changes are complete before you reset the system.
15. Once all physical connections to the PIVD100R have been made and the Control
Port IP address has been assigned or configured, you also have the option to
complete the system setup remotely using either the web GUI or the command line
interface.
• To complete the system setup in the current session (via the Service Port),
continue with step 16.
• If you wish to complete the setup remotely, reset the system at this time: At either
the Command > prompt or the Setup Command > prompt, type reset and press
Enter. When you are ready, establish remote communication with the PIVD100R,
and then continue with step 16. Note that you may use the GUI to perform the
configuration steps, if desired. Refer to the extended Installation & Setup Guide
for further information on establishing remote communication with the PIVD100R
and/or for further information on the GUI.
16. Check the STB Type field in the System Information display (if necessary, you
can rerun the “info” command from either the Command > or Setup Command >
prompt). If the default value (DIRECTV) does not identify the appropriate service
provider, set the STB type as follows:
a) If the Command > prompt is on display, type setup and press Enter to access
the Setup Menu.
(Continued on next page)
18
This document provides installation and setup support only for the PIVD100R. The satellite
dish antenna and satellite STBs must be installed and operating before you proceed to set
up the PIVD100R. LG recommends that the system be professionally installed.
206-4203
Satellite Dish Antenna
__ Ensure the appropriate satellite dish configuration (either 3-LNB or 5-LNB depending
on the satellite provider) is in place for MPEG-4 HD channel reception. If the number
of transcoders exceeds the dish antenna capacity, multi-switch equipment will be
required. For more information, refer to the manufacturer’s documentation.
Satellite STBs
__ DIRECTV satellite service: Up to eight COM 23 satellite STBs are supported for
either RF or IP output.
__ DISH Network satellite service: Up to six ViP ® 222 or ViP 222k satellite STBs are
supported for RF output, or up to eight ViP 222 or ViP 222k satellite STBs are
supported for IP output.
__ Refer to the manufacturer’s documentation, and carefully follow the system setup
procedures for each satellite STB. (The satellite STBs provide the X-Port signal
inputs for the PIVD100R.)
__ Authorization from the satellite service provider is required for HD channels. Contact
the provider to get subscription programming authorization for each satellite STB.
PIVD100R
__ Unpack the PIVD100R unit and all accessories.
PIVD100R
Accessories:
• AC Power Cord and Adapter
• 8 x 1 meter CAT5E Cables (for X-Port connections)
__ Select the location for mounting the PIVD100R. Ensure that adequate ventilation is
available.
__ Obtain the necessary attachment hardware to mount the PIVD100R chassis in its
targeted location.
__ Plan and install the necessary cabling and network (Ethernet) and AC power access
for the PIVD100R. You will also need the following to connect a PC directly to the
PIVD100R for system setup purposes: FTDI TTL-USB cable (P/N TTL-232R-5V-AJ).
206-4203
7
Setup Information (Cont.)
System Setup (Cont.)
(Continued from previous page)
Channel Assignments for RF Output
__ Create a channel assignment plan for the installation site, or modify an existing plan
to incorporate the RF output of the PIVD100R. Ensure that up to four contiguous
CATV channels are allocated for the RF output. The PIVD100R uses a 256-QAM
modulation format, thereby occupying approximately 24 MHz of frequency spectrum.
The RF start channel is user-assigned during system setup, and the remaining
channels are then automatically assigned per EIA-542 STD CATV frequency allocation standards. For example, if the RF start channel assignment is channel “2,” the
three remaining channels will be “3” “4” and “5”. However, if the RF start channel
assignment is “6,” the three remaining channels will be “95” “96” and “97”. Refer to
EIA-542 STD CATV frequency allocation tables for further information as required.
The highest available RF channel number for the PIVD100R is “135.” Thus, to
allocate all four channels available for PIVD100R RF output, the RF start channel
must be set no higher than “132.”
Channel Assignments for IP Output
__ The PIVD100R outputs IPv4 multicast streams. Ensure the institution’s IP network
and room receivers support IPv4 multicast and that the network is capable of
selectively routing multicast traffic. Refer to vendor equipment documentation for
further information.
__ Create a channel assignment plan for the installation site, or modify an existing
plan to incorporate the IP output of the PIVD100R. Ensure that up to 16 unused
and unreserved IPv4 multicast addresses, within the designated range 224.0.0.0 to
239.255.255.255, are allocated for the PIVD100R IP output.
The system will display an overview of the settings, for example:
RF config:
Mode 2, QAM-B, RF: 6 MHz, 5.36 MSps
RF channels:
7 8 9 10
f)
Caution: For proper system performance, the PIVD100R signal level at
the TV input (ANTENNA IN) must be between 0 to +7 dBmV. Note that
additional equipment (i.e., attenuators) may be required to adjust the
signal level.
g) Go to step 14.
13. (IP output only) Complete PIVD100R IP output configuration as follows:
a) If the Command > prompt is on display, type setup and press Enter to access
the Setup Menu.
b) At the Setup Command > prompt, type ipout and press Enter to access the IP
Output Configuration Menu.
c) The IP Output Configuration Menu offers two options for configuring output IP
channels:
• To manually configure the output IP channels, type set and press Enter at the
IP Output Command > prompt. For each STB/tuner, you will need to specify
a multicast IP address and the multicast port number.
• To auto-configure output IP channels from a base multicast IP address and
port number, type fill and press Enter at the IP Output Command > prompt.
Type the base multicast IP address and the multicast port number at the system
prompts. The system will then auto-increment the remaining IP channels.
Refer to the extended Installation & Setup Guide for further information on these
commands.
IP channels are user-assigned during system setup. You may opt to specify an IP
start channel and enable the system to auto-increment the remaining channel
assignments. For example, if the IP start channel assignment is “227.0.0.40,” the
remaining channels will be “227.0.0.41,” “227.0.0.42,” etc. Or, you may opt to
manually specify the IP details for each IP channel.
__ Reserve at least one User Datagram Protocol (UDP) port for the multicast data
streams. You can use the system default (1234) or another unassigned port number
for each data stream, as required, for example, 50000, 50001, etc. The port(s) must
avoid conflict with other protocols in use.
Note: Refer to the IANA IPv4 Multicast Address Space Registry and/or the IANA Service
Name and Transport Protocol Port Number Registry for further IP address/port information
as required.
Refer to the CodePlus™ PIVD100R Pro:Idiom ® Video Distribution Transcoder
System Installation & Setup Guide for further installation and configuration information.
Product documentation is available online at: www.LGsolutions.com/products.
8
206-4203
Connect RF OUT on the PIVD100R rear panel to the RF distribution center
combiner, and balance the RF signal so that the signal level at the TV(s) is
between 0 to +7 dBmV.
d) Once you have completed the output IP channel configuration as required, at the
IP Output Command > prompt, type apply and press Enter to confirm and
apply the configuration data to the system. Then, type exit and press Enter at
the next IP Output Command > prompt to return to the Setup Menu prompt.
e) Connect a CAT5E or better cable between the Feature Port on the PIVD100R
rear panel and the institution’s IP distribution network.
f)
Continue with step 14.
(Continued on next page)
206-4203
17
System Setup (Cont.)
Rear and Front Panel Overviews
(Continued from previous page)
PIVD100R Rear View
10. Check the Output field in the System Information display. If the default value (RF)
does not identify the appropriate output type, set the output mode as follows:
a) At the Command > prompt, type setup and press Enter to access the Setup Menu.
b) At the Setup Command > prompt, type omode and press Enter to set the output mode. The system will display a list of the available output mode options (RF
or IP), followed by a prompt for the new output mode:
Enter number of new output mode [1]>
RF-O
UT
X-Po
rt 8
76
5
RF Out
X-Po
c) At the prompt, type the number that corresponds to the appropriate output mode
and press Enter.
The system will confirm your selection, for example:
rt 4
32
1
Feat
ure
Port
Disconnect Device
The AC mains plug is used
as the disconnect device.
The disconnect device must
remain readily operable.
Output mode is set: IP
11. The next step depends on the output mode:
• If you are setting up the system for RF output, continue with step 12.
Cont
ro
l Po
X-Ports
8, 7, 6, 5
rt
Serv
ice
Port
USB
POW
ER
X-Ports
4, 3, 2, 1
Service Port
Feature & Control
(Ethernet) Ports
USB Ports
• If you are setting up the system for IP output, go to step 13.
AC Power
Cord & Adapter
12. (RF output only) Complete PIVD100R RF output configuration as follows:
a) If the Command > prompt is on display, type setup and press Enter to access
the Setup Menu.
b) At the Setup Command > prompt, type rf and press Enter. The system will
display a list of RF mode options, followed by a prompt for a selection:
Select a new RF mode [2]:
PIVD100R Front View
c) At the prompt, type the number that corresponds to the appropriate RF mode and
press Enter.
Note: By default, the PIVD100R is configured for QAM-B RF output; thus, the default value in square brackets should show the appropriate option for RF output, in
which case, you can simply press Enter at the prompt to accept the default value.
d) At the Enter a new RF channel [3]: prompt, either press Enter to accept
the default value in square brackets, or type a new RF start channel number and
then press Enter.
e) At the Enter number of channels [4]: prompt, either press Enter to
accept the default value in square brackets, or type the applicable number of
channels (Maximum = 4) and then press Enter.
(Continued on next page)
16
206-4203
PW
R
STA
TU
S
Ventilation Holes
Air flow must not be obstructed. To
ventilate the system normally and
avoid overheating, leave at least 1
inch (2.5 cm) on each side (including
top and bottom) of the PIVD100R.
Do NOT stack other equipment on
the top of the PIVD100R.
206-4203
POWER LED
STATUS LED
9
Rack Installation
System Setup (Cont.)
(Continued from previous page)
Typical Rack Installation
1. (Optional) As shipped, the PIVD100R mounting brackets are attached flush with the
front of the unit (see diagram a). If desired, the mounting brackets may be detached
from the unit and reattached, for example, so that they are flush with the rear of the unit
(see diagram b). If you wish to change the location/orientation of the mounting brackets,
carefully remove each of the four (M4 x 10 mm) screws and attendant washers (one
flat and one lock washer per screw) holding each bracket in place. Then, use the same
screws and washers to reattach the mounting brackets in the desired location.
2. Carefully slide the chassis into a standard 19-inch equipment rack.
8. At the Command > prompt, type info and press Enter. (Note that you can press
Enter at any PIVD100R command prompt to view current menu.)
The initial System Information display identifies PIVD100R default configuration
settings, including the Control Port IP address, the STB type, and the output
configuration, for example:
PIVD100R
Pro:Idiom Video Distribution Transcoder System
Copyright (c) 2010-2012 LG Electronics U.S.A., Inc.
Copyright (c) 2010-2012 Zenith Electronics LLC
3. Use all four mounting screws to secure the chassis to the rack.
SN:
Version
HW id:
Ctrl MAC:
Ctrl IP:
STB Type:
Output:
RF config:
RF channels:
Local time:
(a)
PW
R
ST
AT
US
To rack
7. At the login as: prompt, type admin and press Enter. Then, type the admin user
password (provided by LG) at the password: prompt.
101-12470001
1.5
3-207-79-4
00:0C:63:3B:00:BE
136.166.60.92
DirecTV
RF
Mode 2, QAM-B, RF: 6 MHz, 5.36 MSps
3 4 5 6
Thu Mar 22 14:42:02 CDT 2012
9. Check the Ctrl IP (Control Port IP address) field in the System Information display.
By default, the PIVD100R uses DHCP; thus, the DHCP server, if configured, assigns
an IP address to the PIVD100R once the PIVD100R successfully connects to the
network.
To rack
• If the Ctrl IP field shows an IP address, the PIVD100R is up and running on the
network. Continue with step 10.
• If the network is configured for DHCP but the Ctrl IP field is blank, refer to “Network
(b)
Setup” troubleshooting information on page 21.
RF-O
UT
X-Po
rt 8
76
5
• If the network is not configured for DHCP, you will need to configure a static IP
address for the PIVD100R. Complete steps 10 to 13 (as required), and then set the
PIVD100R IP address using the commands indicated in step 14.
X-Po
rt 4
32
1
Feat
ure
Po
rt
Cont
rol
Po
rt
Serv
ice
Port
USB
POW
ER
(Continued on next page)
Use flat washer and
lock washer with each
M4 x 10 mounting
bracket screw.
10
206-4203
206-4203
15
System Setup (Cont.)
Rack Installation (Cont.)
Typical System Installation
(see also Typical Setup Flow Charts on the previous pages)
1. Verify that each satellite STB is set up and functioning. Each STB should be powered
up, initialized, authorized, and displaying the default channel properly—refer to the
manufacturer’s documentation.
Front View
of Rack Cabinet
Caution: Do NOT make any connections between the satellite STBs and
the PIVD100R until you have verified that the STBs are authorized and
functioning properly.
1 inch minimum
PWR
STATUS
1 inch minimum
2. For each satellite STB: Connect one of the supplied CAT5E cables between one of the
X-Ports on the PIVD100R rear panel and the ETHERNET port on the satellite STB.
Note: Once you make the connection between a satellite STB and the PIVD100R,
STB front panel and remote control functionality may be limited. If necessary, to
restore IR remote usability, unplug the X-Port cable and reset the STB. (The STB/
tuner channels will be set later during the system setup.)
3. To enable remote management, connect one end of a CAT5 RJ-45 Ethernet cable to
the Control Port on the PIVD100R rear panel, and connect the other end of the cable to
the institution’s network.
Caution: The subnet 192.168.0.x is reserved for STB communication and
cannot be used for the Control Port network subnet. This is the only
restriction; for example, you can use 192.168.1.x, 10.x.x.x, etc. Contact
your service representative for further information.
4. Connect the PIVD100R power supply to the POWER connector on the PIVD100R
rear panel. Then, plug the AC power cord into a powered AC line receptacle. When
power is applied, the PWR (Power) LED on the PIVD100R front panel will initially
flash red and then turn green.
The boot-up process for the PIVD100R may take up to 90 seconds. When boot-up is
complete, the STATUS LED on the PIVD100R front panel will light continuously green.
5. Once the STATUS LED is green, use the FTDI TTL-232R-5V-AJ cable to connect a
PC to the Service Port on the PIVD100R rear panel.
6. Using HyperTerminal or an equivalent terminal emulation program on the PC,
configure the serial port as follows: Bits per second/baud = 115200; Data bits = 8;
Parity = None; Stop bits = 1; Flow Control = None
Once the connection is established, you should see a login prompt. (If the login
prompt is not automatically displayed, press Enter to refresh the screen.)
(Continued on next page)
14
206-4203
Rack-mount Considerations
A. Elevated Operating Ambient
If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible
with the maximum ambient temperature (Tma) specified by the manufacturer (see
Specifications information in this document).
B. Reduced Air Flow
Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. To ventilate the
system normally and avoid overheating, leave at least 1 inch (2.5 cm) on each side
(including top and bottom) of the PIVD100R. Do NOT stack other equipment on the
top of the PIVD100R.
C. Circuit Overloading
Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring.
D. Reliable Earthing
Maintain reliable earthing of rack-mounted equipment. Particular attention should be
given to supply connections other than direct connections to the branch circuit (e.g.
use of power strips).
E. Mains Outlet Earthing
The apparatus with Class I construction must be connected to a mains socket outlet
with a protective earthing connection.
206-4203
11
System Setup
System Setup (Cont.)
Refer to the following diagrams, and complete the system installation as described on
pages 14 to 20.
Typical Setup Flow Chart for PIVD100R with IP Output
Caution: Do NOT make system connections until instructed to do so during
the system installation procedure. In some instances, configuration steps
must be performed before physical connections are made.
Satellite In
Satellite Signal/
Distribution *
Typical Setup Flow Chart for PIVD100R with RF Output
X-Port 1
X-Port 2
X-Port 3
Satellite
STB
Network
..
.
Ethernet
X-Port n **
PIVD100R
Feature Port
Satellite In
Satellite Signal/
Distribution *
X-Port 1
X-Port 2
X-Port 3
Satellite
STB
Laptop
PC
Network
..
.
Ethernet
Service Port
Connection
X-Port n **
CAT5E
Cable
PIVD100R
RF Out
Service Port
Connection
IP
Distribution
Network
Laptop
PC
Roo
Receivm
er
RF
Cable
RF
Distribution
System
* Multi-switch will be necessary if the number of
transcoders exceeds the dish antenna’s capacity.
** Where n is the last X-Port used. Up to eight COM
23 or ViP 222/ViP 222k STBs are supported for IP
output.
Roo
Receivm
er
* Multi-switch will be necessary if the number of
transcoders exceeds the dish antenna’s capacity.
** Where n is the last X-Port used. Up to eight COM
23 or six ViP 222/ViP 222k STBs are supported for
RF output.
Roo
Receivm
er
Roo
Receivm
er
Roo
Receivm
er
Roo
Receivm
er
12
206-4203
206-4203
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising