Lowell pull and turn rack
LOWELL Manufacturing Company
Spec No. 1035
Model Series: LPTR (2 slides/19.22”D)
REV. 02.06.14 (pg. 1/2)
Description:
The LPTR knockdown rack is great inside cabinetry, providing
convenient slide-out access to rackmounted equipment. The
removable base can be mounted flush or recessed up to 1.75
inches [44.45mm] to allow room for equipment protrusions.
The rack secures to its base with front and rear screws. When
equipment is mounted and wired, secure the assembly with
screws through the front security panel. To service equipment,
remove the security panel and slide the rack fully forward, then
push the button (in center of base front) to release the lock
and rotate the rack until it locks securely at 60 or 90-degrees.
Note: When installing rack inside cabinetry, allow sufficient
space at sides for rack rotation. Recessed installations may
not allow enough room to rotate rack 90-degrees.
Six rear cable
lacing bars.
Ships unassembled
in two cartons.
Features:
• Base includes integral turntable with push button release
and two bottom rails to support the slide-out rack.
Rack slides forward from
base, rotates and locks at
60 or 90-degrees.
• Accommodates a load up to 125 lbs. [56 kg]
• Six 11-ga. steel corner-post rails tapped 10-32
• Six cable lacing bars
• EIA compliant
• Front security panel (perforated)
• Made in the U.S.A. with 100% certified U.S. steel
• Black powder epoxy finish
• Ships in two cartons for efficiency: CARTON ONE includes
base with integral turntable, two rear corner-post rails, three
cable lacing bars. CARTON TWO contains rack bottom, four
corner-post rails, two side stiffeners, front security panel,
three lacing bars.
Optional steel top with
black finish (LPTR-TC).
Optional: (order separately)
• Steel Top (LPTR-TC): black steel top.
A & E Specifications:
To Service an Installed Rack:
The rack shall be Lowell Model ________. It shall be formed
from certified U.S. steel and have a smooth black powder
epoxy finish. It shall measure 19.13"W x 19.22"D [486mm W
x 488mm D] and have 19" [483mm] useable depth. Panel
space shall be _____. The rack shall include a base with two
bottom rails and an integral turntable to allow the rack to slide
forward, rotate and lock at 60 or 90-degrees. It shall also include six cable lacing bars and be capable of supporting a load
up to 125 lbs. [56 kg].
1. Remove the security panel (two screws). If panel is not used,
lock the rack by replacing the screws without the panel.
Model No.
Description
LPTR2-1019
LPTR2-1219
LPTR2-1419
LPTR2-1619
LPTR2-2119
LPTR2-2419
LPTR-TC
Pull & Turn Rack – 2 slides
Pull & Turn Rack – 2 slides
Pull & Turn Rack – 2 slides
Pull & Turn Rack – 2 slides
Pull & Turn Rack – 2 slides
Pull & Turn Rack – 2 slides
Steel Top Cover
2. Pull the rack forward to clear the opening.
3. Push the button in the center front of the base to release the
turntable and rotate the rack 60 or 90-degrees (right or left).
Note: rotate the rack 90-degrees before tying cables to rear
lacing panels to ensure adequate length at maximum turn
radius.
Racking Space
Overall Depth
Useable Depth
Overall Height
Overall Width
17.50 in / 445 mm / 10U
21.00 in / 533 mm / 12U
24.50 in / 622 mm / 14U
28.00 in / 711 mm / 16U
36.75 in / 933 mm / 21U
42.00 in / 1067 mm / 24U
19.22 in / 488 mm
19.22 in / 488 mm
19.22 in / 488 mm
19.22 in / 488 mm
19.22 in / 488 mm
19.22 in / 488 mm
19.00 in / 483 mm
19.00 in / 483 mm
19.00 in / 483 mm
19.00 in / 483 mm
19.00 in / 483 mm
19.00 in / 483 mm
20.08 in / 510 mm
23.58 in / 599 mm
27.08 in / 688 mm
30.58 in / 777 mm
39.33 in / 999 mm
44.58 in / 1132 mm
19.13 in / 486 mm
19.13 in / 486 mm
19.13 in / 486 mm
19.13 in / 486 mm
19.13 in / 486 mm
19.13 in / 486 mm
1 rack unit (RU or U) = 1.75 inches or 44.45 mm. Some measurements have been rounded.
©2014 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069 | 800.325.9660 | www.lowellmfg.com | Lowell makes every effort to provide
accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification.
Spec No. 1035
REV. 02.06.14 (pg. 2/2)
Assemble the rack and base, then dock the rack into position
Rack turned 90 degrees for cabling tie-off.
Perform wire tie off when rack is rotated
90-degrees to ensure adequate slack.
Dock rack to base and secure with
front/rear screws. Then secure with
two screws through front security
panel.
When equipment is mounted and
wired, secure rack with two screws
through front security panel.
Security
panel
Rack turned 60-degrees
Rack slid out from base
Rack turned 90-degrees
Base installation
16” [406 mm]
.261” [7 mm] hole
if mounting to stud
1.41” [36 mm]
18.13” [461 mm]
12.13” [308 mm]
6” [152 mm]
11” [279 mm]
281” [7 mm] holes for mounting
13.97”
[355 mm]
19.22”
[488 mm]
3” [76mm]
19.13” [486 mm]
©2014 Lowell Manufacturing Company, 100 Integram Dr., Pacific MO 63069 | 800.325.9660 | www.lowellmfg.com | Lowell makes every effort to provide
accurate information while reserving the right to change specifications and/or improve manufacturing methods without notification.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising