lwlan‑800
Functions
L‑WLAN Wireless LAN Interface
LWLAN‑800
Datasheet #89032818
L‑WEB
The L‑WLAN Interface expands a LOYTEC device with a wireless LAN connection.
The wireless LAN Interface LWLAN‑800 can be used with L‑INX Automation Servers,
L‑ROC Room Controllers, the L‑GATE Universal Gateways, L-IP Routers of the series
ECTC, NIC709-IP3E100C Remote Network Interfaces, and with most L‑VIS Touch
Panels. The L‑WLAN Interface only needs to be connected to the USB port. Due to
the USB bus, the L‑WLAN device is energy supplied and detected automatically.
L‑ROC
The L‑WLAN Interface uses the protocol IEEE 802.11n improvements which significantly increase connection speed, is backward compatible to IEEE 802.11b &
IEEE 802.11g, offers a link speed up to 150 Mbps, and an operation frequency/
channel:
Accessories
Interfaces
Routers, NIC
L‑DALI
L‑VIS, L-STAT
Gateways
L‑IOB
L‑INX
• USA (FCC)
11 Channels:
2.412 GHz ~ 2.462 GHz
• Europe (ETSI) 13 Channels:
2.412 GHz ~ 2.472 GHz
• Japan
2.412 GHz ~ 2.472 GHz
13 Channels:
After attaching an LWLAN‑800 Interface to the USB port of the corresponding LOYTEC device, it is possible to connect it to
an existing WLAN Access Point, create a WLAN Access Point, or build up a Mesh network (IEEE 802.11s). The relatively new
and emerging standard for Mesh networks offers numerous advantages. A major benefit of a Mesh network is its autonomy. Mesh point configured devices unite autonomously to one network in which Mesh points communicate via other
Mesh points. To encrypt a WLAN network the encryption methods WEP, WPA, and WPA2 are available. The Mesh network is
encrypted via simultaneous authentication of equals (SAE), comparable to WPA2.
The supplied antennas have a radial gain of up to +2 dBi and have to be mounted outside any metallized housing. To avoid
any interferences, please keep a minimum distance of 0.5 m to any electronic devices which also operate with high-frequency signals such as of transformers, ballasts, computers, etc.
Features
• Configuration through web interface
• Increased range through MIMO (multiple-input and
multiple-output) – exploiting multipath propagation
• Two external 2.4 GHz antennas included
• Possibility for connecting external
antennas via 2 SMA sockets (50 Ω)
• Supports Mesh networking according to IEEE 802.11s
• Supports encryption WEP, WPA, and WPA2
Specifications
Type
LWLAN‑800
Dimensions (mm)
27 x 88.5 x 59 (L x W x H), DIM038, Antenna DIM039
Installation
DIN rail mounting following DIN 43880, top hat rail EN 50022
The WLAN antennas have to be installed outside any metallized housing.
Power supply
Via the USB 2.0 bus connection
Operating conditions
0 °C to 50 °C, 10 – 90 % RH @ 50 °C, non condensing, degree of protection: IP40, IP20 (terminals)
Installation
Connected with a standard USB 2.0 cable, max. 5 m
Interfaces
1 x SMA 50 Ohm, RX Antenna 2.4 GHz
1 x SMA 50 Ohm, TX/RX Antenna 2.4 GHz
2 x WLAN antenna magnetic base, cable length = 1 m
1 x USB 2.0 Type B
Frequency
2.4 GHz band
Standard
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.11s
RF Output Power
max. 18 dBm (63 mW) ±2 dBm
Tools
Configuration via web interface
For use with
L‑INX Automation Servers, L‑GATE Gateways, L‑ROC Room Controllers, LVIS‑3ME7-Gx,
LVIS‑3ME12-Ax, LVIS‑3ME15-Ax, LVIS‑3ME15-Gx, LIP-xECTC, NIC709-IP3E100C
Order number
Product description
LWLAN‑800
Wireless LAN Interface IEEE 802.11bgn
156
www.loytec.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising