Preliminary version
Preliminary version
1
RoboSpot MotionCamera
Table of contents
1. Safety instructions.......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains............................................................................................. 6
3.2 Rigging the fixture....................................................................................................... 6
3.4 DMX-512 connection................................................................................................... 8
3.5. Wireless DMX operation............................................................................................ 8
4. Connection with the RoboSpot...................................................................................... 9
5. Control menu map......................................................................................................... 10
6. Control menu ................................................................................................................ 11
6.1 Addressing (DMXA)................................................................................................... 11
6.2 Fixture information (Info)........................................................................................... 11
6.3 Personality (Pers)...................................................................................................... 11
6.4 Manual Control (Manual)........................................................................................... 12
6.7 Reset......................................................................................................................... 12
6.8 Special functions (Special)........................................................................................ 12
7. RDM................................................................................................................................ 13
8. Error and information messages................................................................................. 14
9. Technical Specifications............................................................................................... 15
10. Maintenance and cleaning.......................................................................................... 17
10.1 Replacing the fuse.................................................................................................. 18
10.2 Cleaning of the air filtr............................................................................................. 19
10.3 Disposing of the product......................................................................................... 19
2
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR RoboSpot MotionCamera !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
The RoboSpot MotionCamera was designed for indoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the fixture.
This fixture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable
to completely remove power from unit when not in use or before cleaning or servicing the unit.
Do not allow anything to rest on the power cord. Do not locate this fixture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power
cord from time to time.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this fixture to a dimmer pack.
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Avoid brute force when installing or operating the fixture.
This fixture was designed for indoor use only, do not expose this unit to rain or use near water.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat, moisture
or dust.
Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of
the device and to protect it from overheating.
3
This fixture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Always use a secondary safety cable when rigging this fixture.
Make sure that the area below the installation place is blocked when rigging, de-rigging or servicing the fixture.
Operate the fixture only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the fixture. Most damages are the result of unprofessional operation!
Please use the original packaging if the fixture is to be transported.
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
To avoid damage of the internal optical system of the camera, never let the sunlight or
other fixture lights directly to the camera lens , even when the fixture is not working !
4
2. Fixture exterior view
1 - Camera lens
2 - Moving head
3 - Yoke
4 - Base
5 - DMX Out (5-pin XLR)
6 - DMX In (5-pin XLR)
7 - Camera output (RJ45)
8 - Control board
9 - Mains In
10 - Mains Out
5
3. Installation
Fixtures must be installed by a qualified electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Connection to the mains
For protection from electric shock, the fixture must be earthed!
The RoboSpot MotionCamera is equipped with auto-switching power supply that automatically adjusts to any
50-60Hz AC power source from 100-240 Volts.
If you need to install a cord cap on the power cable to allow connection to power outlets, install a grounding-type
(earthed) plug, following the plug manufacturer’s instructions.
If you have any doubts about proper installation, consult a qualified electrician.
Core (EU)
Core (US)
Connection
Plug Terminal Marking
Brown
Black
Live L
Light blue
White
Neutral
N
Yellow/Green
Green
Earth
This device falls under class one and must be earthed (grounded)!
3.2 Rigging the fixture
A structure intended for installation of the fixture(s) must safely hold weight of the fixture(s) placed on it. The
structure has to be certificated to the purpose.
The fixture must be installed in accordance with national and local electrical and construction codes and regulations.
For overhead installation, the fixture must be always secured with a safety wire that
can bear at least 10 times the weight of the fixture.
When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
The fixture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
materials and the fixture. If you lack these qualifications, do not attempt the installation yourself, but instead use
a professional structural rigger. Improper installation can result in bodily injury or damage to property.
The fixture has to be installed out of the reach of people.
The fixture must never be fixed swinging freely in the room.
6
Caution: Fixture may cause severe injuries when crashing down! If you have doubts concerning the safety of
a possible installation, do not install the moving head!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the fixture’s weight.
.
CAUTION!
Use an appropriate clamp to rig the fixture on the truss.
Make sure that the device is fixed properly! Ensure that the
structure (truss) to which you are attaching the fixture is secure.
The fixture can be placed directly on the stage floor or rigged on a truss without altering its operation characte­
ristics.
For securing the fixture to the truss install a safety wire that can hold at least 10 times the weight of the fixture.
Use only the safety wire with a snap hook with screw lock gate. Fasten the snap hook in the attachment point
and the safety wire around the truss as shown on the picture below.
1-Quick-lock fastener
2-Omega holder
3-Trust
4-Clamp
5-Safety wire with a snap hook
with screw lock gate
6-Attachment point
When installing fixtures side-by-side, avoid illuminating the fixture with another
fixture!
7
3.3 DMX-512 connection
The fixture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair
cable designed for RS-485 and 5-pin XLR-plugs and connectors in order to connect the controller with the
fixture or one fixture with another.
DMX outputDMX input
XLR socket:XLR plug:
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Used for wireless DMX
5 - Used for wireless DMX
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Used for wireless DMX
5 - Used for wireless DMX
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with the
DMX input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs,
you need to use adapter-cables.
3.4. Wireless DMX operation
The external Robe Wireless CRMX-LB100 module allows receiving wireless DMX. This module is equipped
with the Lumen Radio CRMX module and antenna for receiving DMX signal. CRMX module operates on the
2.4 GHz band.
Robe Wireless CRMX-LB100
1 - 5-pin XLR (female)
2 - Locating pin
3 - Lock
Push in the 5-pin XLR plug (1) into 5-pin XLR sockit (4) and simultaneously locating pin (2) into hole (5) in the
fixture. In this way the wireless DMX module is connected with the fixture.
NOTE: when you disconnect the DMX wireless module from fixture, press and hold lock (5) during getting the
wireless module out.
To link the fixture with DMX transmitter.
The fixture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Stat“ (Special -->Vireless -->Stat).
To unlink the fixture from DMX transmitter.
The fixture can be unlinked from receiver via the menu item “ Unlink“ (Special-->Vireless -->Unlink).
8
4. Connection with the RoboSpot
Up to 12 ROBIN BMFL fixtures (Spot/Blade/WashBeam) can be connected to the RoboSpot MotionCamera.
9
5. Control menu map
Default settings=Bold print
Level 1
Level 2
Level 3
DMXA
Set DMXA
001-255
DMX Pres
Mode 1
POn Time
Total
Info
Level 4
Level 5
Level 6
Reset
DMX In
Pan
0-255
:
Reserved
Sw Ver
IC-1
IC-2
Pers
DMX Pres
Mode 1
Pan Rev
On, Off
Tilt Rev
On, Off
P/T Mode
Speed
Time
P/T Feed
On, Off
Display
Turn
On/Off T
On, Off
Contrast
0-100%
Backlight
0-100%
Temp Uni
°C, °F
I Ef Pos
Pan
:
Reserved
Store
Defaults
Manual
Pan
0-255
:
Reserved
Reset
Special
RDM Low
RDM Hight
Wireless
Stat
Unlink
Adjust
DMX Val
Pan
0-255
:
Reserved
Calib
Cal Mech
Pan C
0-255
Tilt C
0-255
Store
Cal Load
SW Upd
10
Level 7
6. Control menu
The RoboSpot MotionCamera is equipped with 2-row LCD display which allows to set the fixture´s behaviour
according to your needs and obtain information about its operation.
Control panel:
[ESCAPE] button used to leave the menu without saving changes.
[NEXT] , [PREV] buttons for moving between menu items and for value adjusting.
[ENTER] button used to enter the selected menu (menu item) and to confirm adjusted value.
After switching the fixture on, display shows current DMX address.
6.1 Addressing (DMXA)
Set DMXA- Use this menu item to set the DMX start address of the fixture, which is defined as the first channel
from which the RoboSpot MotionCamera will respond to the controller.
If you set, for example, the address 36, the RoboSpot MotionCamera will use channels 36 - 43 for control.
Please, be sure that you do not have any overlapping channels in order to control each RoboSpot MotionCamera
correctly and independently from any other fixture on the DMX data link.
If there is no data received at the DMX input, the display will start to flash "0001” with actually stored DMX address.
6.2 Fixture information (Info)
Pon Time - Power on time. Select this menu to read the number of fixture operation hours.
Total - The item shows the total number of the operation hours since
the RoboSpot MotionCamera has been fabricated.
Reset - The item shows the number of the operation hours that the RoboSpot MotionCamera has been powered on since the counter was last reset.
In order to reset this counter to 0, press and hold both [NEXT] and [PREV] buttons and the
[Enter] button at the same time.
DMX In - DMX readout. The menu is used to read DMX values of each channel received by the fixture.
Sw Ver - Software versions. Select this item to read the software version of the fixture modules.
IC-1 - A pan/Tilt processor.
IC-2 - A display processor.
6.3 Personality (Pers)
Pan Rev - Pan reverse. The item allows to invert pan movement.
Tilt Rev - Tilt reverse. The item allows to invert tilt movement.
P/T Mode - Pan and Tilt movement mode. Use this menu to set mode of the pan/tilt movement.
Speed - Both Pan and tilt will move with the same speed as adjusted at the channel
"Pan/Tilt speed, Pan/Tilt time".
Time – The pan and tilt will move with different speeds and they will come at
the same time to the end point of their tracks (pan and tilt use their optimal speeds).
Time of the pan/tilt movement (25.5 sec. max.) is set by the channel "Pan/Tilt speed, Pan/Tilt
time".
11
P/T Feed - Pan and Tilt Feedback. The menu item allows to return the mowing head to the required pan/tilt
position after changing the position by an external force if this option is set on.
Note. The Pan/Tilt Feedback should be permanent On, the option Off is not suitable for standard operation and
the head of the fixture can be damaged!
Display - Display adjusting. This menu allows you to adjust the display behaviour.
Turn - This function rotates menu 180 degrees from current orientation..
On/Off T - This function allows you to keep the display permanent on (On/Off T= Off)
or turn it off two minutes after last pressing any button on the control panel (On/Off T= On).
Contrast- Use this function to adjust contrast of the display (0-100%).
Backlight- Use this function to adjust backlight of the display (0-100%).
I Ef Pos - Init effect positions. Use the menu to set all effects to the desired positions at which they will stay
after switching the fixture on without DMX signal connected.
Defaults - The menu item allows to set all fixture parameters to the default (factory) values.
6.4 Manual Control (Manual)
Use the menu to control all fixture channels by means of the control panel.
6.7 Reset
This option enables the RoboSpot MotionCamera to index all effects and return to their standard positions.
6.8 Special functions (Special)
RDM Low - This menu item shows the first part of the RDM identification code.
RDM High - This menu item shows the second part of the RDM identification code.
Wireless - Stat - Use the menu to read wireless DMX status.
Unlink - use this item to unlink fixture from wireless DMX.
Adjust - Adjustment. The menu allows the fine adjustment of effects.
DMX Val- DMX values. Use the menu to set DMX values of fixture´s channels.
Calib - calibration fixture effects.
Cal Mech - Use this menu to calibrate mechanical effects:
Pan C - position of the pan
Tilt C - position of tilt
Calibration of the pan/tilt via the control board
1. Disconnect DMX controller from the fixture and enter the "Cal P/T" menu.
2. Use the [PREV] and [NEXT] to find "Pan" and press [ENTER].
3. Set desired value and save it by pressing [ENTER].
4. Repeat steps 2 and 3 for Tilt.
5. After calibrating both effects, find item "Store" and press [ENTER]. to save all adjusted values and reset the
fixture.
Sw Upd - Software update. The menu item allows you to update software in the fixture via either serial or
USB port of PC.
The following are required in order to update software:
- PC running Windows 7/10 or Linux
- Update software
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note 1: Software update should execute a qualified person. If you lack qualification, do not attempt the update
yourself and ask for help your ROBE distributor.
12
Note 2: All items in the menu "Pers" will be set to their default (factory) values after software update.
To update software in the fixture:
I. Installation of the update software.
1. Update Software available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the program to the directory.
II.Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
- with the USB input of the Robe Universal Interface if you using the USB cable. Connect DMX
output of the Robe Universal Interface with the fixture via a standard DMX cabel.
Turn both the computer and the fixture on. Make sure the lamp is switched off (only if the fixture
has a lamp).
2. Switch the fixture to the updating mode (Special -> "SW Upd "-> On).
Note: If you do not want to continue in software update, you have to switch off and on the fixture
to escape from this menu.
We recommend to cancel all running programs on PC before starting the software update.
3. Run the Software Uploader. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is finished, the line with the text “The fixture is successfully updated“ will appear in
this window and the fixture will reset with the new software.
Note: In case upload process is interrupted (e.g. power loss), the fixture stays in “Updating mode” and you will
have to repeat the software update again.
7. RDM
This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specifications
for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for RoboSpot MotionCamera is the following.
Parameter ID
Discovery command SET command
DISC_UNIQUE_BRANCH
*
DISC_MUTE
*
DISC_UN_MUTE
*
GET command
DEVICE_INFO
*
SUPPORTED_PARAMETERS
*
SOFTWARE_VERSION_LABEL
*
DMX_START_ADDRESS
*
*
IDENTIFY_DEVICE
*
*
DEVICE_MODEL_DESCRIPTION
*
MANUFACTURER_LABEL
*
*
DEVICE_LABEL
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
*
DISPLAY_INVERT
13
*
DISPLAY_LEVEL
*
*
PAN_INVERT
*
*
TILT_INVERT
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
PARAMETER_DESCRIPTION
*
ROBE_DMX_INPUT
*
ROBE_WIRELESS_UNLINK
*
*
8. Error and information messages
Tilt Err
This message will appear after the reset of the fixture if the head´s magnetic-indexing circuit malfunctions
(sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head
is not located in the default position after the reset.
Pan Err
This message will appear after the reset of the fixture if the head´s magnetic-indexing circuit malfunctions
(sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head
is not located in the default position after the reset.
14
9. Technical Specifications
Electrical
Power supply: electronic auto-ranging
Input voltage range: 100-240V, 50-60Hz
Fuse: T 1A
Max. power consumption: 35W (I=0.22A at 230V, power factor=0.51)
Mains input: CE - max. 16A
ETL - max. 10A
Mains output: CE - max. 15A
ETL - max. 9A
Camera
Pan/Tilt
Control
Type: SNZ-6320
Max. resolution: 1920 x 1080
16 : 9 Full HD (1080p) resolution support
32x optical zoom, 16x digital zoom
H.264, MJPEG dual codec, Multiple streaming
Day & Night (ICR), WDR (120dB)
Pan movement range 540°
Tilt movement range 270°
16 bit movement resolution
Automatic Pan/Tilt position correction
Remotely controllable speed of pan/tilt
Movement control: tracking and vector
2-row LCD display & 4 buttons
Readout fixture usage, receiving DMX values, temperatures, etc
Built-in analyzer for easy fault finding, error messages
Supported protocols: USITT DMX 512, RDM,
8 control channels
External Wireless DMX/RDM module (option)
Compliance with USITT DMX-512 (1986 & 1990) and 512-A
Full DMX fidelity and frame integrity
Auto sensing of DMX frame rate and frame size
<5ms DMX latency
Operational frequency range of 2402-2480 MHz
Producer: LumenRadio
Connection
DMX data in/out: Locking 5-pin XLR
Power IN: Neutrik True oneNAC3MPX
Power OUT: Neutrik True One NAC3FPX
Camera: RJ 45
Rigging
Mounting points pair of 1/4-turn locks
Mounting horizontally or vertically via mounting bracket Omega CL
Temperatures
Maximum ambient temperature : 45° C
Maximum housing temperature : 55° C
15
Total heat dissipation
150 BTU/h (calculated)
Weight
5.7 kg
Dimensions (mm)
Included items
1 x RoboSpot MotionCamera
1 x Mounting bracket Omega CL (P/N 99010420)
Optional accessories
(P/N 10980127) Robe Wireless CRMX-LB100
(P/N 1305 2439) Daisy Chain PowerCon TRUE1 In/Out, EU, 2m, indoor
(P/N 1305 2440) Daisy Chain PowerCon TRUE1 In/Out, US, 2m, indoor
(P/N 13052444) Daisy Chain PowerCon TRUE1 In/Out, EU, 5m, indoor
(P/N 1305 2405) Mains Cable PowerCon In TRUE1/Schuko, 2m, indoor
(P/N 1305 2406) Mains Cable PowerCon In TRUE1/US, 2m, indoor
(P/N 1305 2407) Mains Cable PowerCon In TRUE1/open ended, 2m, indoor
(P/N 13052443) Mains Cable PowerCon In TRUE1/Hubb 2321, 2m US, indoor
(P/N 13052445) Mains Cable PowerCon In TRUE1/CEE 16A, 2m, indoor
16
10. Maintenance and cleaning
DANGER !
Disconnect from the mains before starting any
maintenance work
Never use solvents for cleaning the front lens and covers of the fixture
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build
up on or within the fixture.
A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!
Camera lens may require weekly cleaning as smoke-fluid tends to building up residues.
The interior of the head and base should be cleaned at least annually using a vacuum-cleaner.
Periodically clean the air filter placed in the fixture base. Use a vacuum cleaner, compressed air or you can
wash it and put back dry.
More complicated maintenance and service operations are only to be carried out by authorized distributors.
17
10.1 Replacing the fuse
Before replacing the fuse, unplug mains lead!
1.Replace the fuse by a fuse of the same type and rating only.
2. Remove the plastic covers of the base (1) by unscrewing two
fastening screws (2) on each cover.
3. Unscrew four screws (3) on the top chassis (4). Lay down
the fixture and unscrew four screws (5) on the bottom plate
(8) to push out inside module of the base.
4. Unscrew two screws (7) on the bottom plate to remove
rear panel of the fixture (6).
5. Now you have access to the fuse holder (9) in
the inside module of the base.
6. Remove the old fuse from the fuse holder.
7. Install the new fuse into the fuse holder.
8. Assemble the base of the fixture.
18
10.2 Cleaning of the air filtr
Before replacing the fuse, unplug mains lead!
1. Remove the front plastic cover of the base (1) by unscrewing two fastening screws (2) on the cover.
2. Clean the air filter (3) placed in the base. Use a vacuum cleaner, compressed air or you can wash it and
put back dry.
3. Place the base cover back and fasten it by means of two screws (2).
10.3 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.
June 30, 2017
Copyright © 2017 Robe Lighting - All rights reserved
All Specifications subject to change without notice
Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici
19
DMX protocol
RoboSpot MotionCamera - DMX protocol
Version: 1.0
Channel
DMX
Value
Function
Type of
control
Pan (8 bit)
1
0 - 255
Pan movement by 540° (128=default)
0 - 255
Fine control of pan movement (0=default)
proportional
Pan Fine (16 bit)
2
proportional
Tilt (8 bit)
3
0 - 255
Tilt movement by 270° (128=default)
proportional
Tilt fine (16 bit)
4
0 - 255
Fine control of tilt movement (0=default)
proportional
Pan/Tilt speed , Pan/Tilt time
5
0
1 - 255
1 - 255
Max. speed -tracking mode (0=default)
Pan/Tilt speed
Speed from max. to min. (vector mode)
Pan/Tilt time
Time from 0.1 s to 25.5 sec.
step
proportional
proportional
Power/Special functions
6
0 -19
20-24
25-29
30-34
35-39
40-49
50-54
55-255
Reserved (0=default)
To activate following functions, stop in DMX value for at least 3
seconds.
Display ON
Display OFF
Pan/Tilt speed mode
Pan/Tilt time mode
Reserved
Pan/Tilt reset
Reserved
step
step
step
step
step
Reserved
7
0- 255
Raw DMX (0=default)
0- 255
Raw DMX (0=default)
proportional
Reserved
8
proportional
Copyright © 2017 Robe Lighting s.r.o. - All rights reserved
All Specifications subject to change without notice
Page 1
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising