t140 compact track loader specifications

t140 compact track loader specifications
T140 COMPACT TRACK LOADER SPECIFICATIONS
DIMENSIONS
A)
B)
C)
D)
E)
F)
G)
H)
I)
J)
K)
L)
Operating Height .................................... 143.5" (3645 mm)
Height with Operator Cab ...................... 77.4" (1967 mm)
Angle of Departure ................................. 30°
Ground Contact Length .......................... 48.4" (1230 mm)
Length without Attachment ..................... 95.8" (2432 mm)
Length with Standard Bucket ................. 124.1" (3153 mm)
Rollback @ Ground Position ................. 25°
Dump Height with Standard Bucket ....... 82.8" (2104 mm)
Height to Bucket Hinge Pin .................... 109.6" (2783 mm)
Dump Reach @ Maximum Height ......... 25.6" (649 mm)
Dump Angle @ Maximum Height ........... 40°
Rollback Fully Raised
@ Maximum Height .............................. 96°
M) Width over Bucket
56" Bucket ..................................
N) Turning Radius
with Standard Bucket ...............
Rear Clearance of Machine .....
O) Track Tread
11.8 in. tracks .............................
P) Width (over tracks)
11.8 in. tracks ............................
56.0" (1422 mm)
77.2" (1960 mm)
56.5" (1434 mm)
43.2" (1097 mm)
55.0" (1397 mm)
Carry Position ............................................... 9.2" (233 mm)
Ground Clearance ........................................ 7.8" (197 mm)
PERFORMANCE
Rated Operating Capacity (SAE J732 - no more than 35% of Tipping Load) ........................... 1400 lbs. (635 kg)
Operating Capacity (no more than 50% of Tipping Load) ......................................................... 2022 lbs. (917 kg)
Tipping Load (SAE) .................................................................................................................. 4044 lbs. (1834 kg)
Operating Weight (SAE) .......................................................................................................... 6660 lbs. (3021 kg)
Travel Speed ........................................................................................................................... 7.3 mph (11,8 km/hr)
Lift Breakout Force (SAE) ....................................................................................................... 2650 lbs. (1202 kg)
Tilt Breakout Force (SAE) ....................................................................................................... 3500 lbs. (1588 kg)
Push Force .......................................................................................................................... 4500 ft.-lbs. (2041 kg)
*Rated operating capacity (ROC) @ 35% of Tipping Load complies with ISO 14397-1 and SAE J 818 for crawler loaders.
Bobcat T140 Compact Track Loader Specifications
March 11, 2008
ENGINE/ELECTRICAL
Make/Model .................................... Kubota/V2403-MDI-E3
Fuel/Cooling .................................... Diesel/Liquid
Horsepower (SAE Gross) ............... 49 HP (36 kW)
Maximum Governed RPM ............... 2700 RPM
Torque @ 1650 RPM (SAE Net) ..... 109.6 ft–lbs. (148,60 Nm)
Number of Cylinders ....................... 4
Displacement .................................. 148.5 cu. in. (2,4 L)
Bore/Stroke ..................................... 3.43 / 4.03 in. (87 / 102 mm)
Fuel Consumption ........................... 1.8 gph (6,8 L/h)
Estimated fuel consumption is based on testing by
Bobcat Company in high duty cycle digging applications.
Lubrication ...................................... Pressure System with Filter
Crankcase Ventilation ..................... Closed Breathing
Air Cleaner ...................................... Dry replaceable cartridge with safety element
Ignition ............................................. Diesel-Compression
Engine Coolant ............................... Propylene glycol/water mix (53%-47%) with freeze protection
to -34°F (-37°C)
Starting Aid ..................................... Glow plugs
Alternator ........................................ Belt driven; 90 amps; Ventilated
Battery ............................................ 12 volt; 600 cold cranking amps @ 0°F(-18°C);115 minute reserve capacity
Starter ............................................. 12 volt, gear reduction type; 4.02 HP (3,0 kW)
HYDRAULIC SYSTEM
Pump Type .............................................. Engine Driven, gear type
Pump Capacity, Standard Flow .............. 16.9 GPM (64,0 L/min) @ 3135 RPM
System Relief @ Quick Couplers ........... 2650 - 2750 PSI (183 - 189 Bar)
Hydraulic Filter ....................................... Full flow replaceable, Number 3 micron synthetic media element
Hydraulic Cylinders ................................. Double-acting; tilt cylinders have cushioning feature on dump
and rollback
Control Valve ........................................... 3-Spool, open center type with float detent on lift and electrically
controlled auxiliary spool
Fluid Type ................................................ Bobcat Hydraulic/Hydrostatic Fluid (P/N 6563328)
Motor oil is not an acceptable alternative fluid.
Bore Diameter
Lift Cylinder (2) ................................. 2.00 in. (50,8 mm)
Tilt Cylinder (1) ................................. 3.50 in. (88,9 mm)
Rod Diameter
Lift Cylinder (2) ................................. 1.25 in. (31,8 mm)
Tilt Cylinder (1) ................................. 1.50 in. (38,1 mm)
Stroke
Lift Cylinder (2) ................................. 26.57 in. (674,9 mm)
Tilt Cylinder (1) ................................. 14.50 in. (368,3 mm)
Hydraulic Function Times
Raise Lift Arms ................................. 2.6 Seconds
Bucket Dump ......................... 2.2 Seconds
Lower Lift Arms ................................. 1.8 Seconds
Bucket Rollback ..................... 1.8 Seconds
Bobcat T140 Compact Track Loader Specifications
March 11, 2008
DRIVE SYSTEM
Main Drive .................Fully hydrostatic, rubber track drive
Transmission ............Infinitely variable tandem hydrostatic piston pumps,
driving two fully reversing hydrostatic motors
Tracks .......................11.8 in. width (300 mm)
Tension-grease cylinder and spring rollers–triple flange
GROUND PRESSURE
CAPACITIES
Ground Pressure ....... 5 PSI (34,5 kPa)
Fuel Tank .................................... 15.4 gals. (50,4 L)
Cooling System ............................ 12.0 qts. (11,4 L)
Engine Oil with Filter ........................ 9.5 qts. (9,0 L)
Hydraulic/Hydrostatic Reservoir ... 3.5 gals. (13,3 L)
Hydraulic/Hydrostatic System ....... 6.0 gals. (22,7L)
CONTROLS
Vehicle Steering ........................ Direction and speed controlled by two hand levers
Loader Hydraulics
Lift & Tilt .............................. Controlled by separate foot pedals or optional Advanced Control System (ACS)
Front Auxiliary (Std.) .......... Controlled by electrical switch on Right Hand steering lever
Rear Auxiliary (Opt.) .......... Controlled by electrical switch on Left Hand steering lever
Auxiliary Pressure Release ...... Pressure is relieved through the coupler block, push in and hold for five seconds
Engine ....................................... Hand lever throttle; key-type starter switch and shutdown
Starting Aid ............................... Glow Plugs – automatically activated by Standard or Deluxe Instrument Panel
Service Brake ............................ Two independent hydrostatic systems controlled by two hand operated
steering levers
Secondary Brake ...................... One of the hydrostatic transmissions
Parking Brake ............................ Finger-operated rocker switch on center control panel with
spring applied, pressure release multi disk brake
SERVICEABILITY
Access is available to the following through the rear door/tailgate and rear screen
Air cleaner
Alternator
Battery
Cooling system (radiator and hydraulic oil cooler) for cleaning
Engine oil and fuel filters
Engine oil drain and dipstick
Fuel fill
Hydraulic oil fill
Starter
Bobtach pivots have replaceable wear bushings
Easy access to all lift arm grease points
Rod end of the tilt cylinder has a replaceable bushing
Tailgate has an optional lock for vandal proofing
Tailgate is equipped with door stop to hold door open while servicing
Tip-up operator cab gives access to certain hydraulic system components
Bobcat T140 Compact Track Loader Specifications
March 11, 2008
INSTRUMENTATION
The following loader functions are monitored by a combination of gauges and warning lights in the operator’s
line of sight. The system alerts the operator of monitored loader malfunctions by way of an audible alarm and
visual warning lights.
Standard Instrument Panel
Gauges
Engine Coolant Temperature
Fuel
Hourmeter
Warning Lights
Advanced Control System (ACS)
Engine Air Filter
Engine Coolant Temperature
Engine Oil Pressure
Fuel Level
General Warning
Hydraulic Filter
Hydraulic Oil Temperature
Hydrostatic Charge Pressure
Seat Belt
System Voltage
Indicators
Attachment Control Device
BICS Functions
Glow Plugs
Deluxe Instrument Panel (Option)
Same gauges, warning lights and other features as Standard Instrument Panel plus:
Bar-type gauges: ........................................ Engine Oil Pressure, System Voltage, Hydrostatic Charge Pressure
and Hydraulic Oil Temperature
Additional features: .................................... Keyless Start with password capability, Digital Clock, Job Clock,
Attachments Information, Digital Tachometer, Help Screens,
High Flow Lockouts (if applicable), Multi-Language Display, Diagnostic
Capability and Engine/Hydraulic Systems Shutdown Function
ATTACHMENTS
Angle Broom*
Auger
Backhoe
Bale Forks
Box Blade
Box Blade with Laser*
Brush Saw
Brushcat Rotary Cutter
Buckets
Chipper*
Combination Bucket
Concrete Mixer
Digger
Dozer Blade*
Dumping Hopper
Grader*
Grapple, Farm/Utility
Grapple, Industrial
Hydraulic Breaker
Landplane
Landscape Rake
Mower
Pallet Fork - Standard
Pallet Fork - Hydraulic
Planer
Rear Stabilizer
Scarifier
Scraper
Seeder
Snow Blade
Snow V-Blade*
Snowblower*
Sod Layer
Soil Conditioner
Spreader
Sweeper
* Requires Attachment Control Kit
For specific model availability - See Bobcat Product Price List.
Three-Point Hitch
Tiller
Tilt-Tatch
Tree Spade
Trench Compactor
Trencher
Utility Forks
Vibratory Roller
Water Kit
Whisker Broom
Bobcat T140 Compact Track Loader Specifications
March 11, 2008
FACTORY OPTIONS
Advanced Control System (ACS)
Selectable Joystick Control (SJC)
Back-up Alarm and Horn
Engine Block Heater
Hydraulic Bucket Positioning
DEALER ACCESSORIES
Attachment Control Kit
Back-up Alarm
Cab Accessory Harness
Cab Enclosure
Catalytic Exhaust Purifier
Fire Extinguisher Kit
FOPS Kit - Level II**
Four-point Lift Kit
Four-Way Flasher Light Kit
Horn
Hydraulic Bucket Positioning
Locking Fuel Cap
Power Bob-Tach
Radio
Rear Auxiliary Hydraulics
Rotating Beacon Light
Side Windows Kit
Single-point Lift Kit
Special Applications Kit
Strobe Light Kit
Tailgate Lock Kit
HEATED CAB PACKAGES
H71 Option Package
Cab Enclosure with Heat
Power Bobtach
Sound Reduction
Deluxe Instrumentation Panel
Cab Accessory Harness
Attachment Control Kit
H51 Option Package
Cab Enclosure with Heat
Power Bobtach
Cab Accessory Harness
OPEN CAB PACKAGES
O71 Option Package
Power Bobtach
Deluxe Instrumentation Panel
Cab Accessory Harness
Attachment Control Kit
O51 Option Package
Deluxe Instrumentation Panel
Cab Accessory Harness
H31 Option Package
Cab Enclosure with Heat
Cab Accessory Harness
Bobcat T140 Compact Track Loader Specifications
March 11, 2008
SAFETY
Bobcat Interlock Control System
(BICS) (Std.) ............................................. Requires the operator to be seated in the loader with the
seatbar in place and the engine running. After the operator presses
the “Press to Operate Loader” button, the loader’s hydraulic lift and tilt
functions and traction drive system can be operated.
Lift Arm Bypass Control (Std.) ................. Used to lower the lift arms in the event that the lift arms cannot
be lowered during normal operating conditions
Seat Belt (Std.) ......................................... Should always be worn when operating the loader
Seat Bar (Std.) ......................................... Secondary operator restraint, also serves as an arm rest
Operator Cab (Std.) .................................. An enclosable operator cab with side screens with a minimal
inside cab width of 33" (838 mm) as standard equipment.
Meets SAE J1040 and ISO 3471 for Roll Over Protective Structure
(ROPS) and SAE J1043 and ISO 3449 Level I for Falling Object
Protective Structure (FOPS). Level II option is available.
Level I – Acceptance is intended for protection from falling bricks, small concrete blocks and hand tools
encountered in operations such as highway maintenance, landscaping and other construction site services.
Level II – Acceptance is intended for protection from falling trees or rocks for machines involved in site clearing,
overhead demolition or forestry.
Lift Arm Support (Std.) ................................ Use for servicing when lift arms are raised
Parking Brake (Std.) .................................... Always set brake when leaving loader
Grab Handles (Std.) ..................................... Should always be used when entering/exiting loader
Safety Tread (Std.) ...................................... Slip resistant tread on lift arms and main frame to be used
when entering/exiting loader
Attachment Steps (Std.) ............................. Should always be used when entering/exiting loader
Rear Window (Std.) ..................................... For emergency exit
Front & Rear Working Lights (Std.) ............ Use for indoor and low light operation
Backup Alarm (Opt.) .................................... For use in jobs with low visibility
Lift Kits (Opt.) .............................................. Lift kits are available so loader may be lifted into remote areas
Special Applications Kit (Opt.) .................... Restricts objects and material from entering cab openings
Operator’s Handbook (Std.) ......................... Weather resistant operator handbook written in English will be
attached to inside of cab, providing operational instructions and
warnings by decals with pictorials and international symbols plus
some messages in four basic languages: English, French, German
and Spanish.
TRAINING RESOURCES
These optional videotapes and training courses are available through Bobcat Parts
Bobcat Skid-Steer Loader Operator Training Course
4-hour course provides video, classroom and hands-on training (also available in Spanish)
Bobcat Skid-Steer Loader Service Safety Training Course
2-hour course provides video, classroom and hands-on training
Bobcat Skid-Steer Loader Safety Video
Short and to-the-point video provides basic safety instructions for the Skid-Steer Loader
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising