020-101335-02_LIT MAN REF EnteroHB Commands.book

020-101335-02_LIT MAN REF EnteroHB Commands.book
R e f e ren c e G u i d e
020-101335-02
Entero HB Serial Commands
NOTICES
COPYRIGHT AND TRADEMARKS
Copyright © 2014 Christie Digital Systems, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in
this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may
vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications
are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited
to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages
in connection with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.
WARRANTY
Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or
Christie. In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your
product, the warranty does not cover:
a. Problems or damage occurring during shipment, in either direction.
b. Projector lamps (See Christie’s separate lamp program policy).
c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie lamp supplied
by Christie or an authorized distributor of Christie lamps.
d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or
use of a product with any non-Christie interface device.
e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an unauthorized distributor of
Christie lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or
components through the internet (confirmation of authorized distributors may be obtained from Christie).
f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.
g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a
Christie authorized repair service provider.
h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed,
modified or approved by Christie for such use.
i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is unrelated to the
projector.
j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which means the LCD
projector is not used more than 8 hours a day, 5 days a week.
k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is
protected from precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended
ambient temperature set forth in the specifications for such product.
l. Image retention on LCD flat panels.
m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product
sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is
located or (ii) the required international warranty fee has been paid.
The warranty does not obligate Christie to provide any on site warranty service at the product site location.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for specific
maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule
specified by Christie, will void the warranty.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at the user’s own expense.
CAN ICES-3 (A) / NMB-3 (A)
이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을
목적으로 합니다 .
Environmental
means that electrical and The product is designed and manufactured with high‐quality materials and components that can be recycled and reused. This symbol
electronic equipment, at their end‐of‐life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!
Content
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RS232 Communication Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connect to the RS232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Message Types and Formats
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Message Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
User Access Permissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CCM–Color and Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
DCA–Display Color Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DEF–Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DID–Display Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DSN–Display Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EDD–EDID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ERR–Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INP–Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ITP–Internal Test Pattern
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LOC–Localization Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LST–List Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MAP–Map Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
NET–Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OSD–On Screen Display
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PNG–Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PWR–Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
REM–Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
RST–Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RTM–Runtime
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SAR–Subarray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SCL–Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SEL–Select
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SHU–Shutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SIX–Six Axis Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SOR–Screen Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TIL–Tiling Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
3
TMD–Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TMP–Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
UID–User ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
UNI–Uniformity
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VER–Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
WIR–Wireless
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
4
Introduction
This document provides information and procedures for using serial commands (ASCII text
messages) to control Entero HB display cubes.
RS232 Communication Parameters
This table lists the communication parameters for the display cube RS232 port.
Parameter
Value
Baud rate
115200 bps
Stop bits
1 bit
Data bits
8 bits
Parity
None
Flow control
None
Connect to the RS232 Port
i
• To send serial commands over the Ethernet port, you must login. Use the UID serial
command to configure the login. See UID–User ID on page 24.
You can use an RS232 connection to remotely access display controls and image setups, issue
commands or queries, and receive replies.
1. Connect one end of a null standard 9-pin female to female modem cable to the projector RS232
port.
2. Connect the other end of the null standard 9-pin female to female modem cable to a computer.
Message Types and Formats
Commands sent to and from the display cube are formatted as simple text messages that consist of
a three letter command code, an optional four letter subcode, and optional data. You can include
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
5
Introduction
optional features such as message acknowledgments with your commands. This table lists the
available message types.
Message Type
Description
Set
A command to set a display parameter at a specific level, such as changing the
brightness.
Request
A request for information, such as what is the current brightness setting.
Reply
The projector returns the data in response to a request or as confirmation of a
command.
Messages are sent and read as ASCII character strings. However, the message travels as a
sequence of bytes. Each character in this sequence requires 1 byte. This example illustrates how a
Power On command is sent to the display.
ASCII =
(
HEX =
0x28
P
W
0x50
R
0x57
1
0x52
)
0x20
0x31
0x29
This table lists the message format.
Source
From Controller
From Display
Format
Function
Example
(Code Data)
SET (set color of selected internal test
pattern to white)
(ITP 4)
(Code+Subcode Data)
SET (set display wall brightness to 800)
(CCM+TBRT 800)
(Code?)
REQUEST (what is screen orientation of
selected displays?)
(SOR?)
(Code Data)
Command dependent and generally represented by space delimited
rows and columns.
Message Structure
This table lists the components of an ASCII command.
Message Element
Description
Parentheses
Commands are enclosed by parentheses ().
If a start character is received before an end character of the previous message,
the partial (previous) message is discarded.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
6
Introduction
Message Element
Description
Prefix characters (optional)
Acknowledges the display cube has responded or increases message integrity
when added before the 3-character function code.
If the message cannot be executed, a not-acknowledge (NAK) is returned.
Use the number symbol (#) to request a full acknowledgment. A full
acknowledgement sends an echo of the message as a reply from the projector
when it finishes processing the command. Do not include a full
acknowledgement in a request message.
Use the dollar symbol ($) to request a simple acknowledgment. When a
command executes successfully, a dollar symbol ($) is returned.
Use the ampersand symbol (&) to add a checksum as the last message
parameter. For example, (&PWR 1 144).
The display collects all of the message bytes as defined in the first byte of the
message, then creates its own checksum value for comparison with the
checksum included in the controller’s message. If the values match, the
message is considered to have been correctly received. If the values do not
match, the message is discarded
Use an “h” to indicate a hex number. If a request message includes a
checksum, a checksum is included with the reply. An acknowledge or checksum
character can occur first.
Display numbers (optional)
Selects a specific display by its system index or display number.
Function code
The primary display cube function being queried or modified. Each function code
is represented by a three-character, upper or lower case ASCII code (A-Z). The
function code appears after the first parenthesis. If a command does not include
a subcode, you must add a space between the function code and the first
parameter (or special character).
+subcode
The secondary display cube function being queried or modified. Each subcode is
represented by a four-character, upper or lower case ASCII code (A-Z and 0-9).
The subcode appears after the function code, and it is separated from the
function code with a plus symbol (+).
If a subcode is not included, the plus symbol is not required. If a command
includes a subcode, you must add a space between the subcode and the first
parameter (or special character).
Request and reply symbols
The question mark symbol (?) appears after the function code when the
controller requests display cube information.
An exclamation mark (!) appears after the function code when the display cube
responds to a request.
Do not include a question or exclamation mark when creating a SET command.
User Access Permissions
Permission
Description
Guest
Can be run without logging in
Admin
The default
Service
Can access all administration and service commands
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
7
Commands
This section list the commands that you can use with Entero HB RPMSP, RPMHD, and RPMWU-LED02
display cubes. To prevent an alteration or an interruption of the controller script, do not use the
web interface or the on-screen display when the script is running. Some commands are operational
only when the display is on.
CCM–Color and Brightness
Modifies color and brightness settings. The color and brightness adjustments are automatically
synchronized between the displays. The settings affect the entire array.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
CCM?
Returns the color and brightness
settings for the array.
-
CCM+TBRT <Brightness>
Sets the brightness for the array.
-
CCM+CLRT
<ColourTemperature>
Sets the color temperature for the array.
-
CCM+TCLR <redx> <redy>
<greenx> <greeny> <bluex>
<bluey>
Sets the target gamut/color space for
the array.
-
CCM+BRTM <mode>
Sets the brightness mode for the array.
0 = Normal Mode
1 = Economy Brightness Mode
2 = Fixed Brightness Mode
3 = High Brightness Mode
CCM+CLRM <mode>
Sets the color gamut mode for the array.
0 = Maximum Gamut
1 = SRGB Gamut
2 = Custom Gamut
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
8
Commands
Command
Description
Values
CCM+WEAK?
Returns the weak display threshold for
each selected display.
-
CCM+WEAK <threshold>
Sets the weak display drop threshold for
the selected displays.
0.0 to 1.0
DCA–Display Color Adjust
Adjusts the color and brightness of a specific display. Affects the selected displays and requires only
one display to be selected.
Parameters
•
Access Level: Admin
Commands
Commands
Description
Values
DCA?
Returns the display color and
brightness settings.
-
DCA <brightness>
<RedofRed> <GreenofRed>
<BlueofRed> <RedofGreen>
<GreenofGreen>
<BlueofGreen> <RedofBlue>
<GreenofBlue>
<BlueofBlue> <RedofWhite>
<GreenofWhite>
<BlueofWhite>
Sets the display color and
brightness.
-200 to 0 = Adjusts brightness
0 to 100 = Adjusts all other parameters
DEF–Factory Defaults
Resets all preference and configuration settings to their default values. To prevent accidental use of
this command, the number 111 must follow the command. Restoring factory defaults does not
affect network settings, date and time.
Parameters
•
Access Level: Service
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
9
Commands
Commands
Command
Description
Values
DEF 111
Performs the factory default command.
111—Must be entered exactly as is
Examples
Reset the projector to factory defaults.
(DEF 111)
(65535 00000 FYI00919 “All settings have been restored to their factory defaults.
Reboot is required to take effect.”)
DID–Display Identification
Sets the number, name, or identifier for the display. Typically, displays are numbered with 0 in the
top left corner and continuing to the right across the row before moving down to the next row. Valid
numbers are 0 to 999. Affects the selected displays.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
DID?
Returns the numbers currently assigned to displays.
-
DID <number>
Assigns a number to a display.
-
DID+AUTO
Automatically numbers all displays in the current array.
-
DSN–Display Serial Number
Retrieves or assigns the serial number for the selected displays.
Parameters
•
Access Level: Service
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
10
Commands
Commands
Command
Description
Values
DSN?
Returns the serial number for the selected display.
-
DSN <serial>
Sets the serial number for the selected display.
-
EDD–EDID
Sets Extended Display Identification Data (EDID) timing for DVI inputs.
Parameters
•
Access Level: Service
Commands
Command
Description
Values
EDD?
Returns the current EDID
timing.
-
EDD+AUTO <port>
Automatically sets the EDID
to values typical for the
display's light engine.
<port>:
0 = For primary DVI input.
1 = For optional secondary DVI input.
all = Both primary and secondary DVI inputs.
EDD <port> <horizontal>
<vertical> <framerate>
Sets the resolution and
framerate.
<horizontal> = Sets the horizontal resolution
<vertical> = Sets the vertical resolution
<framerate> = Sets the framerate
ERR–Errors
Displays the error log for the selected displays.
Parameters
•
Access Level: Admin
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
11
Commands
Commands
Command
Description
Values
ERR?
Returns the error log for the selected display.
-
INP–Input
Changes the video input selection properties. The system controls video input through four
predefined modes. By setting a mode, the system monitors video inputs on the DVI inputs and
determine which to display on the screen.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
INP?
Returns the current video input mode.
-
INP <mode>
Sets the video input mode.
0 = Show DVI1 only
1 = Show DVI2 only
2 = Show DVI1; if DVI1 does not have a valid
signal, fallback to DVI 2
3 = Show DVI2; if DVI2 does not have a valid
signal, fallback to DVI 1
ITP–Internal Test Pattern
Displays a predefined test pattern on the display.
Parameters
•
Access Level: Admin
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
12
Commands
Commands
Command
Description
ITP <pattern>
Displays a tests pattern on the display.
Values
1 = None
2 = Grid
3 = Grayscale 16
4 = White
5 = Flat Gray
6 = Black
7 = Checker
8 = 13 Point
9 = Color Bars
10 = Edge Blend
11 = High Frequency
12 = Gradient Blur
13 = Red
14 = Green
15 = Blue
LOC–Localization Language
Sets or returns the language displayed on the user interface and on-screen display.
Parameters
•
Access Level: Administrator
Commands
Command
Description
Values
LOC?
Returns the language used by the selected display.
-
LOC+LANG <language>
Sets the display language.
0 = English
1 = French
2 = Spanish
3 = Italian
4 = German
5 = Japanese
6 = Chinese
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
13
Commands
Examples
Set language to French.
(LOC+LANG 1)
Get language.
(LOC?)
LST–List Displays
Returns a list of all the displays in the current array. All displays in the array respond and color
match.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
LST?
Returns a list of all displays in the current array.
-
MAP–Map Display
Maps displays by their network MAC address. Use the (AVL?) command to return a list of all
displays that can be mapped. Use the (LST?) command to return a list of all displays mapped to the
array.
For effective communication between displays and color matching, all displays in an array must be
mapped. By default, all displays are mapped to the def array. To prevent interference from other
displays connected to the same network, change the default mapping of all displays in an array.
Parameters
•
Access Level: Admin
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
14
Commands
Commands
Command
Description
Values
MAP?
Returns a lists of all Sirius
devices in a network. All displays
in the list can be grouped in an
array.
-
MAP+ADD <mac address>
<array> <x position> 
<y position>
Maps a display to an array and
identifies its position with its MAC
address.
<mac address> = MAC address of the
display
<array> = Array to which the display is
mapped
<x position> = X coordinate in the array
<y position> = y coordinate in the array
MAP+ALL <array> <x
position> <y position>
Maps all displays to the same
array and position. Christie does
not recommend using this
command; each display should
have its x and y positions set
individually.
<array> = Array to which the display is
mapped
<x position> = X coordinate in the array
<y position> = y coordinate in the array
NET–Network Setup
Modifies the network settings of a display. By default, all displays request IP addresses from DHCP
on ETH2. For effective communication between displays and color matching, connect all displays in
an array to the same network.
Parameters
•
Control Group: Configuration/Preference
•
Subclass: Power Down
•
Access Level: Admin
Commands
Command
Description
Values
NET? <port>
Returns the settings of a specific
network port.
-
NET+AUTO <port>
Sets a specific network port to DHCP
mode and removes the static IP
settings.
-
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
15
Commands
Command
Description
Values
NET <port> <ip> <subnet>
<gateway>
Sets the specified network port to use
a static IP.
<port> = Must be 0
<ip> = IP address
<subnet> = Subnet address
<gateway> = Gateway address
OSD–On Screen Display
Displays or removes overlay information in the on-screen display (OSD), including the status,
information, and mapping overlay pages.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
OSD+STAT <0 | 1>
Displays or removes the OSD status
overlay page.
0 = Removes the OSD status overlay page
Displays or removes the OSD info
overlay page.
0 = Removes the OSD info overlay page
Displays or removes the OSD mapping
overlay page.
0 = Removes the OSD mapping overlay page
OSD+INFO <0 | 1>
OSD+MAPP <0 | 1>
1 = Displays the OSD status overlay page
1 = Displays the OSD info overlay page
1 = Displays the OSD mapping overlay page
PNG–Ping
Returns basic projector information to the user, including the type of device and main software
version.
Parameters
•
Access Level: Admin
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
16
Commands
Commands
Command
Description
Return Parameters
PNG?
Returns the return the family ID, model, and
software version for a display
[Family ID] - 53 = Sirius
[Model] - 0 = SXGA+, 1 = H, 2 = WUXGA
[Software Version Major]
[Software Version Minor]
[Software Version Sub]
[Software Version SVN]
PWR–Power
Turns a display on or off, or deactivates auto-power on. By default, auto-power on is active and a
display turns on and video plays when it is reset or turned off. When auto-power on is inactive, the
display enters standby mode when it is reset or turned off.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
PWR?
Returns the power settings for the display. -
PWR <mode>
Changes the display power mode.
0 = Turns the display off
1 = Turns the display on
PWR+AUTO <autopower>
Turns auto-power off or on.
0 = Turns off auto-power on
1 = Turns on auto-power on
REM–Remote
Activates or deactivates the infrared receiver on a display. If the infrared receiver is deactivated,
use the web interface or a serial commend to enable it.
Parameters
•
Access Level: Admin
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
17
Commands
Commands
Command
Description
Values
REM?
Returns the status of the infrared receiver.
-
REM <mode>
Activates or deactivates the infrared receiver.
0 = Deactivates the infrared receiver
1 = Activates the infrared receiver
RST–Reset
Restarts a display.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
RST
Restarts the display.
-
RTM–Runtime
Returns the EM and light engine runtime in hours.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
RTM?
Returns the runtime in hours.
-
SAR–Subarray
Configures settings for the subarrays.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
18
Commands
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
SAR?
From the specified displays, the displays
that belong to subarrays are listed.
Displays that are not part of a subarray
are not listed.
-
SAR+ACTV <mode>
<number>
Turns the specified subarray on or off.
mode =
• 0 = off
• 1 = on
number = Number of the subarray to
apply <mode> to.
• 1-25
• ALL = Apply <mode> to all
subarrays.
SAR+ADDS <number>
<topleftX> <topleftY>
<width> <height>
Creates a subarray that includes all the
displays within the specified coordinate
range.
The SAR+ACTV command must be issued
to activate the subarray before video is
configured.
number = Number of the subarray
being created. 1 to 25
topleftX = X coordinate of top left
corner of new subarray
topleftY = Y coordinate of top left
corner of new subarray
width = Width of the subarray, in
number of displays
height = Height of the subarray, in
number of displays
SAR+DELS <number>
<norefresh>
Deletes a single subarray or all subarrays.
When issued, the specified subarrays are
deleted and the video is reconfigured
automatically.
With the optional <norefresh> parameter,
the specified subarray is deleted, but the
video is not reconfigured.
SAR+REFR
Refreshes the video of all displays causing
them to recalculate the tiling and scaling.
number = Number of the subarray
being deleted.
• 1-25
• ALL = Delete all subarrays.
NOREFRESH = Does not reconfigure
the video after a subarray is deleted.
(Optional parameter)
-
SCL–Scale
Adjusts the scaling mode.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
19
Commands
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
SCL?
Returns the scaling mode.
-
SCL <mode>
Sets the scaling mode.
0 = 1:1, video is centered, scaling not applied
1 = Scale-to-fit, video is centered and scaled to fit the
display native resolution
2 = Scale-to-fit with aspect ratio; video is centered and
scaled while maintaining aspect ratio
SCL+ALL?
Returns the scaling mode and
scale adjustment parameters.
-
SEL–Select
Selects single or multiple displays. You can select displays by their system index, name, or number.
Do not use the web interface or on-screen display (OS) when you run this command.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
SEL?
Returns a list of system indexes for the selected
displays.
-
SEL ALL
Selects all displays.
-
SEL NONE
Deselects all displays.
-
SEL+NAME <number 0> ... <number N>
Selects a display by number ID.
-
Returns a list of number IDs.
SEL <index 0> .. <index N>
Selects a display by index number.
-
Returns a list of indexes.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
20
Commands
SHU–Shutter
Turns the virtual shutter on specific displays on or off. This command can only be run when the
display is on. If the display is in standby mode, the virtual shutter is off. This functionality is not
persistent.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
SHU0
Turns off the shutter.
-
SHU1
Turns on the shutter.
-
Examples
Open the shutter.
(SHU 0)
Close the shutter.
(SHU 1)
Get the state of the shutter (0 for open, 1 for closed).
(SHU?)
SIX–Six Axis Adjuster
Aligns the projected image with the edges of the screen by adjusting the position, keystone, zoom,
and tilt of the image geometry.
Parameters
•
Access Level: Service
Commands
Command
Description
Values
SIX+ZOOM <0|1>
Increases or decreases the six-axis zoom
control.
0 = Decreases the zoom
Increases or decreases the six-axis horizontal
keystone control.
0 = Decreases the horizontal keystone
SIX+HKEY <0|1>
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
1 = Increases the zoom
1 = Increases the horizontal keystone
21
Commands
Command
Description
Values
SIX+VKEY <0|1>
Increases or decreases the six-axis vertical
keystone control.
0 = Decreases the vertical keystone
Increases or decreases the six-axis tilt
control.
0 = Decreases the tilt
Increases or decreases the six-axis horizontal
position control.
0 = Decreases the horizontal position
Increases or decreases the six-axis vertical
position control.
0 = Decreases the vertical position
Sets the access mode for the six-axis
adjuster.
0 = Sets default mode (rear access)
SIX+TILT <0|1>
SIX+HPOS <0|1>
SIX+VPOS <0|1>
SIX+MODE <0|1>
SIX+DOOR
Releases the front access cube door latches.
SIX+STOP
Stops any current adjustment.
1 = Increases the vertical keystone
1 = Increases the tilt
1 = Increases the horizontal position
1 = Increases the vertical position
1 = Sets front access mode, where the
hkey, vkey, hpos, and vpos controls are
reversed.
SOR–Screen Orientation
Changes the orientation of the displayed image.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
SOR?
Returns the screen orientation.
-
SOR <mode>
Sets the screen orientation.
0 = Normal projection (Default,
Rear Projection)
1 = Horizontal flip
2 = Vertical flip
3 = Horizontal and vertical flip
TIL–Tiling Mode
Sends one video input to all tiles and has it automatically stretched across the entire array. For
tiling to work correctly, all displays in the array must be mapped to their correct coordinates.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
22
Commands
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
TIL?
Returns the tiling mode setting.
-
TIL <mode>
Sets the tiling mode.
0 = Disables tiling mode and enables
independent display mode
1 - Enables tiling mode and disables
independent display mode
TMD–Time and Date
Sets the display time and date.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
TMD?
Returns the time and date.
-
TMD+TIME hh:mm:ss
Sets the local time in a 24-hour
clock format.
-
TMD+DATE yy/mm/dd
Sets the date with the format yyyy/
mm/dd.
-
TMD+FULL yy/mm/dd hh:mm:ss
Sets the time and date.
-
Examples
Get the local time.
(TMD+TIME?)
Set the time to 3pm.
(TMD+TIM “15:00:00”)
(65535 00000 FYI0916 “Setting Time to 15:00:00”)
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
23
Commands
Get the date to January 17th, 2015
(TMD+DATE “2015/01/17”)
(65535 00000 FYI--916 “Setting Date to 2015/01/17”)
TMP–Temperatures
Retrieves the historical temperature data for different array areas.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
TMP?
Returns all current temperatures.
-
TMP+PEAK?
Returns all peak temperatures.
-
TMP+AVER?
Returns all average temperatures.
-
TMP+HIST? ALL
Returns all temperature histories.
-
TMP+HIST? ENV
Returns the Environment (ENV) temperature history.
-
TMP+HIST? DMD
Returns the DMD temperature history.
-
TMP+HIST? DRV
Returns the DRV temperature history.
-
TMP+HIST? CPU
Returns the Electronic Module (EM) CPU temperature history.
-
TMP+HIST? RED
Returns the red temperature history.
-
TMP+HIST? BLU
Returns the blue temperature history.
-
TMP+HIST? GRN
Returns the green temperature history.
-
UID–User ID
Applies a username and password to access serial command subsets. The available logins are
guest, user, admin, and service. The default is guest on the TCP connection, web interface, and onscreen display. The default for the serial port is admin.
Parameters
•
Access Level: Guest
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
24
Commands
Commands
Command
Description
Values
UID?
Returns the current access level.
-
UID <username password>
Logs in with the username and
password. Do not add quotation
marks or spaces.
-
UID
Resets the log in to the default
settings.
Default access settings:
Web interface—guest—can only run
the UID command.
On-screen display—user— additional
access privileges can be configured
through the OSD interface.
TCP—guest—can only run the UID
command.
Serial—user—additional access
privileges can be configured through
the UID command.
UNI–Uniformity
Adjusts the display so no area appears brighter than another.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
UNI?
Returns the uniformity status.
-
UNI <mode>
Sets the brightness uniformity mode.
0 = Sets brightness uniformity mode off
1 = Sets brightness uniformity mode on (Default)
VER–Version
Retrieves the firmware version.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
25
Commands
Parameters
•
Access Level: Admin
Commands
Subcode
Description
Values
VER?
Returns the firmware version running on the selected display.
-
VER+BOOT?
Returns the bootloader version running on the selected display.
-
WIR–Wireless
Configures the wireless network connection.
Parameters
•
Access Level: Admin
Commands
Command
Description
Values
WIR?
Returns the wireless settings.
-
WIR+MODE <0|1>
Turns the wireless connection on or off.
0 = Turns wireless off
1 = Turns wireless on
WIR+MODE 1 <ssid> <pass>
Turns the wireless connection on and specifies the
service set identification (SSID) and password.
Entero HB Serial Commands Reference Guide
020-101335-02 Rev. 1 (12-2014)
-
26
Corporate offices
Worldwide offices
USA – Cypress
ph: 714-236-8610
Australia
ph: +61 (0) 7 3624 4888
Canada – Kitchener
ph: 519-744-8005
Brazil
ph: +55 (11) 2548 4753
Consultant offices
China (Beijing)
ph: +86 10 6561 0240
Italy
ph: +39 (0) 2 9902 1161
China (Shanghai)
ph: +86 21 6278 7708
Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
France
ph: +33 (0) 1 41 21 44 04
Germany
ph: +49 2161 664540
India
ph: +91 (080) 6708 9999
Singapore
ph: +65 6877-8737
Japan (Tokyo)
ph: 81 3 3599 7481
Spain
ph: +34 91 633 9990
Korea (Seoul)
ph: +82 2 702 1601
United Arab Emirates
ph: +971 4 3206688
Republic of South Africa
ph: +27 (0)11 510 0094
United Kingdom
ph: +44 (0) 118 977 8000
For the most current technical documentation, please visit www.christiedigital.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising