op7361 datasheet - Opal-RT
OP7361 DATASHEET
8X SFP Carrier
www.opal-rt.com
Published by
Opal-RT Technologies, Inc. 1751 Richardson, suite 2525 Montreal, Quebec Canada H3K 1G6
www.opal-rt.com
© 2013 Opal-RT Technologies, Inc. All rights reserved
Printed in Canada


CONTENTS
OP7361 8X SFP CARRIER....................................................................................................................... 5
DESCRIPTION ..................................................................................................................................... 5
features. .............................................................................................................................................................5
INSTALLATION...................................................................................................................................... 5
STATUS DISPLAY.................................................................................................................................. 6
connectors..........................................................................................................................................................6
typical channel diagram.......................................................................................................................................7
SPECIFICATIONS................................................................................................................................. 7
OP7361 Datasheet OPAL-RT Technologies 3
OP7361 8X SFP Carrier

OP7361 8X SFP CARRIER
DESCRIPTION
The OP7361 is designed to fit in the front of the OP7000 chassis. The OP7361 is an 8xSFP carrier
to be inserted on the front of the OP7000. This board is installed in a secondary FPGA slot and uses
available high speed links to communicate externally. An SFP (Small Form-factor Pluggable) module is
a compact, hot-pluggable transceiver used for both telecommunication and data communications.
SFP transceivers are available with a variety of transmitter and receiver types, allowing users to select
the appropriate transceiver for each link to provide the required optical reach over the available optical
fiber type (e.g. multi-mode fiber or single-mode fiber).
The OP7361 Carrier is compatible with :
• SFP multi-mode fiber only,
• SFP that can run up to 4 Gbps with available bitrate of: 1, 1.25, 2, 2.5, 4, 5 Gbps.
features
• Status display, with push-button control
• 8 fiber optic connectors.
1
OP7P3c6
arrier
8 SF
INSTALLATION
The OP7361 module must be inserted at the front of the OP7000 simulator, in
an odd numbered slot, making sure that the board is properly aligned using the
guide tracks before pressing into place.
CH00
CH01
CH06
CH02
CH07
CH03
OPAL-RT Technologies CH05
OP7361 Datasheet CH04
Make sure that the board corresponds to the compatible board at the rear of the
chassis.
5
OP7361 8X SFP Carrier
status Display
STATUS DISPLAY
The OP7361 is equipped with a status display interface that is operated by a pushbutton. The
pushbutton allows you to select a channel, and its status – what channel is linked to the slot – will then
be displayed in the display area. Press to move to the next channel.
The LEDs associated to the selected channel will blink to indicate the channel is selected:
• Green arrow will blink to show where to plug the SFP module.
• Red arrow indicates a problem with the SFP link (communication RX loss, or TX fault).
61 r
OP73ca
rrie
8 SFP
Matrix Slot
Number Indicator
Pushbutton
Matrix FPGA
Number Indicator
CH00
CH04
LED Indicator
(channel selector)
(channel selected)
CH02
CH07
CH03
CH00
CH01
CH06
CH04
CH05
Communication
Channel
The top two matrix slot indicators display the slot number where the SFP is connected.
The lower two matrix slot indicators display the FPGA slot associated to each SFP. This allows you to
identify exactly what the channel is connected.
connectors
Use an SFP transceiver and a fiber optic cable (as shown) to connect to the OP7361.
SFP TRANSCEIVER
6
FIBER OPTIC CABLE
OPAL-RT Technologies
OP7361 Datasheet
OP7361 8X SFP Carrier
SPECIFICATIONS
typical channel diagram
Direct connection
to OP7161-x FPGA
high speed link
SFP Module 0
Multi-mode fiber
SFP Module 1
Multi-mode fiber
SFP Module 2
Multi-mode fiber
SFP Module 3
Multi-mode fiber
...
SFP Module 6
Multi-mode fiber
SFP Module 7
Multi-mode fiber
Figure 25: Channel diagram
SPECIFICATIONS
Product name
OP7361
Part number
126-0445
Product type
OP7000 8-SFP carrier board
Dimensions
Board: (connectors excluded) 16 x 10 cm (6.3 in x 4 in)
Plate: 12.87 x 4.03cm (5.06 x 1.59in)
Operating temperature
10 to 40 ºC (50 to 104ºF)
Storage temperature
-55 to 85ºC (-67 to 185ºF)
Relative humidity
10 to 90%, non condensing
Maximum altitude
2,000 m (6562 ft.)
OP7361 Datasheet OPAL-RT Technologies 7
CONTACT
Opal-RT Corporate Headquarters
1751 Richardson, Suite 2525
Montréal, Québec, Canada
H3K 1G6
Tel.: 514-935-2323
Toll free: 1-877-935-2323
Note:
While every effort has been made to ensure
accuracy in this publication, no responsibility
can be accepted for errors or omissions. Data
may change, as well as legislation, and you are
strongly advised to obtain copies of the most
recently issued regulations, standards, and
guidelines.
This publication is not intended to form the
basis of a contract.
Technical Services
www.opal-rt.com/support
DS13-09059-OP2
06/2013
© OPAL-RT Technologies Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising