RP-2002(E) - Control Fire Systems Ltd.
DN-60240:C1
RP-2002(E)
Agent Release Control Panel
Conventional Releasing Panels
General
The RP-2002 is a six-zone FACP for single and dual hazard
agent releasing applications. The RP-2002 provides reliable
fire detection, signaling and protection for commercial, industrial and institutional buildings requiring agent-based releasing.
The RP-2002 is compatible with System Sensor’s i3 detectors
which are conventional smoke detectors that can transmit a
maintenance trouble signal to the FACP indicating the need for
cleaning and a supervisory ‘freeze’ signal when the ambient
temperature falls below the detector rating of approximately
45°F (7.22°C). In addition, the control panel is compatible with
conventional input devices such as two-wire smoke detectors,
four-wire smoke detectors, pull stations, waterflow devices,
tamper switches and other normally-open contact devices.
Refer to the Notifier Device Compatibility Document for a complete listing of compatible devices.
Activation of a compatible smoke detector or any normallyopen fire alarm initiating device will activate audible and visual
signaling devices, illuminate an indicator, display alarm information on the panel’s LCD, sound the piezo sounder at the
FACP, activate the FACP alarm relay and operate an optional
module used to notify a remote station or initiate an auxiliary
control function.
The RP-2002E offers the same features as the RP-2002 but
allows connection to 220/240 VAC. Unless otherwise specified, the information in this data sheet applies to both the 110/
120 VAC and 220/240 VAC versions of the panels.
RP2002.jpg
Four outputs are programmable as NACs (Notification Appliance Circuits) or releasing circuits. Three programmable
Form-C relays (factory programmed for Alarm, Trouble and
Supervisory) and 24 VDC special application resettable and
non-resettable power outputs are also included on the main
circuit board. The RP-2002 supervises all wiring, AC voltage,
battery charger and battery level.
•
•
•
•
•
Features
• Listed to UL Standard 864, 9th edition.
• FM Approved.
• Designed for agent releasing standards NFPA 12, 12A,
12B, and 2001.
• Meets International Building Code (IBC) seismic requirements.
• Disable/Enable control per input zone and output zone.
• Extensive transient protection.
• Dual hazard operation.
• Adjustable pre-discharge, discharge and waterflow delay
timers.
• Cross-zone (double-interlock) capability.
• Six programmable Style B (Class B) IDCs (Initiating Device
Circuit).
• System Sensor i3 series detector compatible.
• Four programmable Style Y (Class B) output circuits - (special application power).
• Strobe synchronization:
– System Sensor
– Wheelock
•
•
•
•
•
•
•
•
– Gentex
– Faraday
– Amseco
Three programmable Form-C relays.
7.0 amps total 24 VDC output current.
Resettable and non-resettable output power.
Built-in Programmer.
ANN-BUS connector for communication with optional
devices (up to 8 total of any of the following):
– N-ANN-80 Remote LCD Annunciator
– N-ANN-I/O LED Driver
– N-ANN-S/PG Printer Module
– N-ANN-RLY Relay Module
– N-ANN-LED Annunciator Module
80-character LCD display (backlit).
Real-time clock/calendar with daylight savings time control.
History log with 256 event storage.
Piezo sounder for alarm, trouble and supervisory.
24 volt operation.
Low AC voltage sense.
Outputs Programmable for:
– Releasing Circuits or NACS
NACs programmable for:
– Silence Inhibit
– Auto-Silence
– Strobe Synchronization
– Selective Silence (horn-strobe mute)
– Temporal or Steady Signal
– Silenceable or Non-silenceable
– Release Stage Sounder
DN-60240:C1 • 06/14/2011 — Page 1 of 4
• Automatic battery charger with charger supervision.
• Optional Dress Panel DP-51050 (red).
• Optional Trim Ring TR-CE (red) for semi-flush mounting the
cabinet.
• Optional N-CAC-5X Class A Converter Module for Outputs
and IDCs.
• Optional 4XTM Municipal Box Transmitter Module.
• Optional Digital Alarm Communicators (411, 411UD,
411UDAC).
• Optional ANN-SEC card for a secondary ANN-BUS.
PROGRAMMING AND SOFTWARE:
• Custom English labels (per point) may be manually entered
or selected from an internal library file.
• Programmable Abort operation.
• Three programmable Form-C relay outputs.
• Pre-programmed and custom application templates.
• Continuous fire protection during online programming at the
front panel.
• Program Check automatically catches common errors not
linked to any zone or input point.
USER INTERFACE:
• Integral 80-character LCD display with backlighting.
• Real-time clock/calendar with automatic daylight savings
adjustments.
• ANN-Bus for connection to remote annunciators.
• Audible or silent walk test capabilities.
• Piezo sounder for alarm, trouble, and supervisory.
Controls and Indicators
LED INDICATORS
•
•
•
•
•
•
•
•
FIRE ALARM (red).
SUPERVISORY (yellow).
TROUBLE (yellow).
AC POWER (green).
ALARM SILENCED (yellow).
DISCHARGED (red).
PRE-DISCHARGE (red indicator).
ABORT (yellow indicator).
CONTROL BUTTONS
• ACKNOWLEDGE.
• ALARM SILENCE.
• SYSTEM RESET (lamp test).
• DRILL.
AC Power – TB1
• RP-2002: 120 VAC, 60 Hz, 3.66 amps.
• RP-2002E: 240 VAC, 50 Hz, 2.085 amps.
• Wire size: minimum #14 AWG (2.0 mm2) with 600V insulation.
• Supervised, nonpower-limited.
Battery (sealed lead acid only) – J12:
• Maximum Charging Circuit - Normal Flat Charge: 27.6
VDC @ 1.4 amp. Supervised, nonpower-limited.
• Maximum Charger Capacity: 26 Amp Hour battery (two
18 Amp Hour batteries can be housed in the FACP cabinet.
Larger batteries require separate battery box such as the
BB-26 or NFS-LBBR).
• Minimum Battery Size: 7 Amp Hour.
Page 2 of 4 — DN-60240:C1 • 06/14/2011
Initiating Device Circuits - TB4 and TB6
• Zones 1 - 5 on TB4.
• Zone 6 on TB6.
• Supervised and power-limited circuitry.
• Style B (Class B) wiring with Style D (Class A) option.
• Normal Operating Voltage: Nominal 20 VDC.
• Alarm Current: 15 mA minimum.
• Short Circuit Current: 40 mA max.
• Maximum Loop Resistance: 100 Ohms.
• End-of-Line Resistor: 4.7K Ohms, 1/2 watt (PN 71252).
• Standby Current: 4 mA.
Refer to the Notifier Device Compatibility Document for listed
compatible devices.
Notification Appliance and Releasing Circuit(s) - TB5 and
TB7
• Four Output Circuits.
• Style Y (Class B) or Style Z (Class A) with optional converter module.
• Special Application power.
• Supervised and power-limited circuitry.
• Normal Operating Voltage: Nominal 24 VDC.
• Maximum Signaling Current: 7.0 amps (3.0 amps maximum
per NAC).
• End-of-Line Resistor: 4.7K Ohms, 1/2 watt (PN 71252).
• Max. Wiring Voltage Drop: 2 VDC.
Refer to the Notifier Device Compatibility Document for compatible listed devices.
Form-C Relays - Programmable - TB8
• Relay 1 (factory default programmed as Alarm Relay)
• Relay 2 (factory default programmed as fail-safe Trouble
Relay)
• Relay 3 (factory default programmed as Supervisory Relay)
• Relay Contact Ratings:
– 2 amps @ 30 VDC (resistive)
– 0.5 amps @ 30 VAC (resistive)
Auxiliary Trouble Input – J6
The Auxiliary Trouble Input is an open collector circuit which
can be used to monitor external devices for trouble conditions.
It can be connected to the trouble bus of a peripheral, such as
a power supply, which is compatible with open collector circuits.
Special Application Resettable Power - TB9
• Operating Voltage: Nominal 24 VDC.
• Maximum Available Current: 500 mA - appropriate for
powering 4-wire smoke detectors (see note).
• Power-limited Circuitry.
Refer to the Notifier Device Compatibility Document for compatible listed devices.
NOTE: Total current for resettable power, nonresettable power and
Output Circuits must not exceed 7.0 amps.
Special Application Resettable or Nonresettable Power TB9
Operating Voltage: Nominal 24 VDC.
Maximum Available Current: 500 mA (see note 1).
Power-limited Circuitry.
Jumper selectable by JP31 for resettable or nonresettable
power.
Refer to the Notifier Device Compatibility Document for compatible listed devices.
•
•
•
•
Product Line Information
RP-2002: Six-zone, 24 volt Agent Release Control Panel
(includes backbox, power supply, technical manual, and a
frame & post operating instruction sheet) for single and dual
hazard agent releasing applications.
RP-2002E: Same as above but allows connection to 220/240
VAC.
N-CAC-5X: Class A Converter Module can be used to convert
the Style B (Class B) Initiating Device Circuits to Style D
(Class A) and Style Y (Class B) Output Circuits to Style Z
(Class A).
NOTE: Two Class A Converter modules are required to convert all
four Output Circuits and six Initiating Device Circuits.
4XTM: Transmitter Module provides a supervised output for
local energy municipal box transmitter and alarm and trouble
reverse polarity. It includes a disable switch and disable trouble
LED.
N-ANN-80(-W): LCD Annunciator is a remote LCD annunciator that mimics the information displayed on the FACP LCD
display. Recommended wire type is un-shielded. (Basic model
is black; order -W version for white; see DN-7114.)
N-ANN-LED: Annunciator Module provides three LEDs for
each zone: Alarm, Trouble and Supervisory. Ships with red or
black enclosure (see DN-60242).
N-ANN-RLED: Provides alarm (red) indicators for up to 30
input zones or addressable points. (See DN-60242).
N-ANN-RLY (16911): Relay Module, which can be mounted
inside or outside the cabinet, provides 10 programmable
Form-C relays. (See DN-7107).
N-ANN-S/PG: Serial/Parallel Printer Gateway module provides a connection for a serial or parallel printer. (See DN7103).
N-ANN-I/O: LED Driver Module provides connections to a
user supplied graphic annunciator. (See DN-7105).
ANN-SEC: Optional card for a secondary ANN-BUS.
53944.
See
DP-51050: Dress panel (red) is available as an option. The
dress panel restricts access to the system wiring while allowing access to the membrane switch panel.
TR-CE: Trim-ring (red) is available as an option. The trim-ring
allows semi-flushing mounting of the cabinet.
BB-26: Battery box, holds up to two 26 Amp Hour batteries
and CHG-75.
NFS-LBBR: Battery box, houses two 55 Amp Hour batteries,
red.
SEISKIT-COMMENC: Seismic mounting kit; required for seismic-certified installations.
BAT Series Batteries: Refer to DN-6933.
PRN-6: UL-listed compatible event printer. Dot-matrix, tractorfed paper, 120 VAC.
PRT-PK-CABLE: Programming cable. Used to update the
FACP’s flash firmware. (Also requires an RS485 to RS232
converter).
DN-60240:C1 • 06/14/2011 — Page 3 of 4
SYSTEM SPECIFICATIONS
System Capacity
• Annunciators ..................................................... .................8
Electrical Specifications
• RP-2002 (FLPS-7 Power Supply): 120 VAC, 60 Hz, 3.66
amps
• RP-2002E (FLPS-7 Power Supply): 240 VAC, 50 Hz, 2.085
amps
• Wire size: minimum 14 AWG (2.0 mm²) with 600 V insulation, supervised, nonpower-limited
this system and its peripherals be installed in an environment
with a normal room temperature of 15 – 27°C/60 – 80°F.
NFPA Standards
The RP-2002(E) complies with the following NFPA 72 Fire
Alarm Systems requirements:
– NFPA 12 CO2 Extinguishing Systems
– NFPA 12A Halon 1301 Extinguishing Systems
– NFPA 12B Halon 1211 Extinguishing Systems
– NFPA 72 National Fire Alarm Code for Local Fire Alarm
Systems and Remote Station Fire Alarm Systems
(requires an optional Remote Station Output Module)
– NFPA 2001 Clean Agent Fire Extinguishing Systems
Cabinet Specifications
Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x
0.72" (1.82 cm.) deep. Backbox: 19.00" (48.26 cm.) high x
16.65" (42.29 cm.) wide x 5.25" (13.34 cm.) deep. Trim Ring
(TR- CE): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide.
Shipping Specifications
Dimensions:
– Height 20.00" (50.80cm)
– Width 22.50" (57.15cm)
– Depth 8.50" (21.59cm)
Temperature and Humidity Ranges
This system meets NFPA requirements for operation at 0 –
49°C/32 – 120°F and at a relative humidity 93% ± 2% RH
(noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the
useful life of the system's standby batteries and the electronic
components may be adversely affected by extreme temperature ranges and humidity. Therefore, it is recommended that
Agency Listings and Approvals
The listings and approvals below apply to the basic RP2002(E) control panels. In some cases, certain modules may
not be listed by certain approval agencies, or listing may be in
process. Consult factory for latest listing status.
•
•
•
•
•
UL: S635
FM approved
CSFM: 7165-0028:0245
MEA: 333-07-E
Seismic Listing: Reference certificiate of compliance
VMA - 45894-01 by the VMC Group
NOTE: For ULC-listed model, see DN-60444.
NOTIFIER® and System Sensor® are registered trademarks of Honeywell
International Inc.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
Made in the U.S. A.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Page 4 of 4 — DN-60240:C1 • 06/14/2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising