Simon XTi Installation Guide
Simon XTi Installation Guide
Content
Contact information ................................................................................ 1
Description ................................................................................................... 1
Installation.................................................................................................... 1
Connecting hardwired devices........................................................... 2
Wiring phone lines.................................................................................... 3
Wiring the power transformer ............................................................ 4
Resetting memory to factory defaults ............................................ 4
Programming.............................................................................................. 4
Status & Settings screen........................................................................ 5
Sensors ......................................................................................................... 7
Cleaning the touch screen.................................................................... 9
Disposal ......................................................................................................... 9
Specifications........................................................................................... 10
Regulatory information ....................................................................... 10
Contact information
www.utcfireandsecurity.com or www.interlogix.com
Device
Part number
Recommended
sensor group
4-Button Key fob
600-1064-95R b
01
Simon XT Talking Touch
Screen
60-924-3-XT-2WTTS b
60-924-RF-TS d
00, 01, 04, 05, 06, or
07
Simon XT Talking
Touchpad
60-924-3-XT b
01
Carbon Monoxide alarm
TX-6310-01-1 b, 6006520-95 b
34
a.
b.
c.
d.
Not certified as a primary protection circuit for UL-listed systems
and is for supplementary use only.
Has not been investigated by UL.
Required for UL-listed residential fire alarm applications.
The TWTTS has been verified for use by ETL. Neither this device
nor other devices that employ the UTCFS 80 Bit Enhanced
Protocol have been investigated for use by UL.
Note: These sensor groups are only recommendations. The installer should
choose the correct sensor group for the application.
Caution: Do not use outdoor motion sensors for intrusion
protection.
For customer support, see www.interlogix.com/customer-support
GE and the GE monogram are trademarks of the General Electric
Company and are under license to UTC Fire & Security, 9 Farm
Springs Road, Farmington, CT 06034-4065
Installation
Copyright © 2012 UTC Fire & Security. All rights reserved.
Locate the panel where alarm sounds can be heard and where
the panel will be easily accessible for operation. Do not install the
panel near a window or door where it can be reached easily by an
intruder.
Description
This is the Installation Guide for the Simon XTi system (models 6001054-95R-12 and 600-1054-95R-12-CN).
Panel location
Table 1: Sensors and recommended sensor groups
Device
Part number
Indoor motion sensor
60-639-95R, 60-807-95 b 15, 17, 18, 20, 28, or
32
Entry/exit door
60-362N-10-319.5
10
Interior door
60-362N-10-319.5
14
Door/Window sensor
60-362N-10-319.5
13
Smoke sensor
TX-6010-01-1
26
Glassbreak sensor
60-873-95
b
Recommended
sensor group
c
13
P/N 466-2449 • REV A • 21FEB12
Figure 2: Mounting holes
Mounting
Mounting hole
Figure 1: XTi chassis and trim ring
A
B
Wiring knockout
D
Mounting hole
C
7.
Secure the mounting screws (provided) to the locations on the
wall marked in step 6. Do not tighten the screws. Leave
enough clearance to mount the mounting plate.
Note: Use wall anchors if no studs are present.
To mount the panel on a wall:
8.
Mount the mounting plate to the wall. Insert the top mounting
hole first, then the bottom hole. Adjust the fit to make sure the
mounting plate is level. Hold the mounting plate in place and
tighten the screws.
Separate the panel chassis from the mounting plate by lifting
up on the tabs (A in Figure 1 above) and swinging the chassis
open.
9.
Hang the panel chassis on the mounting plate at the plastic
hinges, swing the chassis up to the mounting plate and
engage at the tabs (A in Figure 1 above).
4.
Choose a panel location.
10. Reattach the trim ring.
5.
Run all necessary power, phone, siren, and hardwired contact
wires to the desired panel location.
Connecting hardwired devices
1.
Lay the panel flat on a table.
2.
Remove trim ring (B in Figure 1 above) from panel by lifting at
notch (C in Figure 1 above).
3.
9 VAC in
Note: Mark both mounting holes in the middle of the
mounting slot. This will allow better adjustment of the panel
before securing it to the wall.
9 VAC in
Figure 3: Wiring terminals
HW2 in
Hold the mounting plate against the wall and mark the
mounting hole locations (Figure 2 below) with a pencil.
HW1&2
DC out
The panel has five screw terminals, two battery terminals, and two
telephone connections. The screw terminals connect the AC
power, sirens, and/or hardwired detectors.
HW1 I/O
6.
When choosing the AC outlet location for the AC power
transformer, make sure the outlet is not controlled by a
switch or that it is not part of a ground fault circuit interrupt
(GFCI).
Program sensors and devices before you install them. Follow the
instructions in “Sensors” on page 7 to add the sensors to panel
memory.
The HW1 I/O terminal is dual purpose and can be used for either
siren or hardwired contact connections. The HW2 in terminal is an
input only.
2
Simon XTi Installation Guide
Interior sirens
Wiring phone lines
From the factory, the HW1 I/O input (terminal 1) is set up for
interior siren operation (status and alarm sounds). The HW1&2 DC
out (terminal 2) provides the positive (+) voltage.
You can connect a phone line to the panel for systems monitored
by a central monitoring station or systems that notify users by a
voice event notification.
Note: The total current available from the HW1&2 DC out terminal
is 250 mA at up to 120ºF (49ºC). A 24-hour battery standby for UL
requirements will be met with a maximum load of 250 mA.
DSL (digital subscriber line) allows the use of multiple devices on a
single phone line simultaneously. For DSL environments, connect
the panel line-in jack to an available phone jack on the premises.
You might also need an inline filter to ensure panel reporting is
successful.
With Hardwired Siren Supervision turned on, sirens connected to
HW1 I/O are supervised and require a 4.7-kohm resistor in the
circuit. If this terminal is not used, turn Hardwired Siren
Supervision off.
Note: Avoid connecting the panel to a standard phone (voice) line,
as other devices on the line can prevent reports from going
through.
Exterior sirens
For an exterior siren, change the HW1 setting in the System
Options programming menu. See wiring diagram.
Full line seizure
Hardwired contacts
Full line seizure allows the panel to take over (seize) the phone line,
even if another device on the line is in use. This method requires
that the panel be wired before all other phones, answering
machines, computers, or other devices on the phone line. You may
need to verify the line seizure for UL installations.
You can connect hardwired reed switches (normally closed loop
only) to HW1 I/O (if not being used for a hardwired siren) and/or
HW2 in (terminal 3).
Use the RJ31X (CA-38A) jack when wiring for full line seizure. You
can then quickly and easily disconnect the panel from the phone
line in case the panel disables the phone line due to a malfunction.
Connect only normally closed (NC) reed switches to HW1 I/O
and/or HW2 in. Other types of hardwired detectors should not be
used.
To wire full line seizure with an RJ31X:
Note: Not investigated for and may not be used in a UL Listed
installation.
The total resistance of the wired loop must not exceed 3 ohms.
This allows you to use up to 200 ft. (61 m) of two-conductor, 22gauge stranded wire.
1.
Run a four-conductor cable from the premises Telco block to
the RJ31X.
2.
Connect the four-conductor cable wire to the RJ31X.
3.
Disconnect the green and red premises phone jack wires
from the Telco block and splice them to the four-conductor
cable black and white (or yellow) wires. Use weatherproof
wire connectors for these splices.
4.
Connect the four-conductor cable green and red wires to the
Telco block TIP (+) and red to RING (-) posts.
5.
Connect the phone cord included with the panel to the RJ31X
and the panel LINE jack.
Connect hardwired reed switches to the panel using a 47-kohm
resistor (not a 4.7-kohm resistor) as shown in Figure 4 below. The
resistor must be connected at the last switch in the circuit.
Figure 4: Normally closed hardwired reed switches
47 kohm resistors
Full line seizure wiring with one premises phone
9 VAC in
9 VAC in
HW2 in
HW1&2
DC out
HW1 I/O
If a single phone is all that exists on the premises, full line seizure
can be accomplished without an RJ31X.
Note: Do not install the resistor at the panel terminals. This does
not provide supervision of the wire.
Simon XTi Installation Guide
1.
Disconnect the phone from the premises phone jack and plug
it into the panel PHONE jack. This jack is disconnected
automatically whenever the panel reports.
2.
Connect the included phone cord to the panel LINE jack and
the premises phone jack.
If a customer adds phones or other phone devices to another
phone jack, full line seizure no longer exists. Inform them to
3
contact you if they want to add a phone or other device so that
you can rewire for full line seizure by adding an RJ31X.
Wiring the power transformer
Connect the power transformer to the two 9 VAC in terminals (4
and 5) on the panel. Do not plug in the transformer at this time.
When applying power to the panel, connect the battery first, and
then plug in the AC power transformer. This sequence prevents a
battery fault condition.
Applying AC power
Make sure the outlet is not controlled by a switch or that it is not
part of a ground fault circuit interrupt (GFCI).
Note: For Canadian installations, plug the transformer into the
wall outlet.
1.
WARNING: Use extreme caution when securing the
transformer to a metal outlet cover. You could receive a
serious shock if a metal outlet cover drops down onto the
prongs of the plug.
Note: System can only be powered up using AC power, not battery
power. The red battery icon may appear when the system first
powers up and will disappear after some time.
2.
Plug the transformer into the lower receptacle of the outlet so
that the hole in the transformer tab lines up with the outlet
cover screw hole.
3.
Insert the cover plate screw through the transformer tab and
the outlet cover plate. Tighten the screw.
To remove and install the backup battery (6 VDC, 2.1 Ah):
Note: It is recommended that the backup battery be replaced
every 3-5 years.
1.
Remove AC power from the panel.
2.
Disconnect the existing battery from the battery connector.
3.
Remove the existing battery by reaching under the battery
with a finger and pulling up.
Note: Upon initial installation, the battery may not be fully
charged for as long as 36 hours. A low battery icon will be
present and trouble beeps will sound until the battery is
sufficiently charged. After the initial charge, should the panel
lose AC Power and experience a low battery condition, the
icon will appear and trouble beeps will sound unless silenced.
You can silence trouble beeps by:
Note: Do not try to push the plastic latch back to remove the
battery.
4.
Insert the new battery into the battery compartment and
snap into place.
5.
Plug the battery connector into the panel.
Remove the center screw from the outlet cover plate and
hold the cover plate in place.
•
Arming or disarming the system.
or
•
Caution: Do not connect the battery until you are ready to power
up the panel.
Pressing the STATUS & SETTINGS icon and pressing
LISTEN next to Panel Status.
This will disable the sounder for 4 hours but the trouble
indication will remain until the battery is recharged.
Resetting memory to factory defaults
If you need to reset memory to factory defaults, follow the steps
below.
To reset the panel to factory defaults:
1.
Remove the trim ring.
2.
Open the panel chassis.
3.
Unplug the transformer and disconnect the battery.
4.
Press and hold the reset button (D in Figure 1 on page 2) on
the left side of the panel.
5.
Plug in the transformer to the panel while holding the reset
button and keeping the panel cover open.
6.
Release the button.
7.
Plug in the battery and close the panel chassis.
8.
Replace the trim ring.
4
Programming
The control panel provides the main processing unit for all system
functions. The programming of system options and features is
menu-driven.
Table 2 below describes the panel’s programming keys and
features.
Table 2: Simon XTi features and home keys
Item
Description
Piezo siren
Provides alarm beeps and status beeps. Fire and
intrusion alarm beeps are always played at high
volume, while the volume of status beeps is
programmable.
Touch screen
Provides a graphical user interface for
programming and system operation.
Microphone
Used to communicate with the central monitoring
station after an alarm.
Simon XTi Installation Guide
Item
Description
Speaker
Provides voice output and sounds key beeps. The
panel speaks arming level change, system status,
and voice chime sensor trips. The panel voice is also
used for voice reporting and remote phone control.
Time
Status & Settings screen
Entering and exiting the Status & Settings screen
To enter the Status & Settings screen:
To access the emergency screen and select the
appropriate emergency icon (Panic, Police, or Fire),
press EMERGENCY in the top left corner of the
screen.
Press the Status & Settings icon
home screen.
Displays the current system time.
Press Close to exit the Status & Settings screen and navigate up
one level.
Depicts the status of the AC power and battery. A
green power cord icon represents AC power to the
system. A red battery icon represents low battery
power to the system. A green battery icon
represents a charged battery.
This will appear on the home screen in the event of
an alarm. Messages will also display on this icon
describing what caused the alarm. Press this icon to
cancel the alarm.
These four icons depict the status of the sensors
installed in your system.
on the lower right of the
To exit the Status & Settings screen:
Note: The system will automatically return to the main screen
after a period of inactivity.
A gold icon indicates an option is selected.
A blue icon indicates an option is not selected.
Status & Settings Screen navigation
1.
Press the up/down arrows to scroll through the pages. (See
Table 3 below for Settings screen structure).
2.
Press an icon to change the value of an option or enter a
subscreen.
Pressing these icons will open a new screen to
provide more detail.
3.
Press Close to return to the previous screen.
If the icon shows N/A, your system is not configured
to support that type of sensor.
Table 3: Status & Settings screen structure
A green check indicates sensors are closed or no
recent activity detected. A red exclamation
indicates sensors are open or recent activity has
been detected.
Option
How to view
Press this icon to access the Arming Screen.
Event History
Press the Show icon to view system events.
Note: If a # appears in the Event History list, the
event was not sent to the central station.
One of these icons will display depending on your
arming level. Press to turn off intrusion/burglary
protection for your system. Only intrusion/burglary
sensors are disarmed. Environmental sensors, such
as smoke and carbon monoxide detectors, stay
active at all times. Enter your code in the keypad
screen that appears. If you enter an incorrect code,
press the Clear icon and enter the correct code.
Direct Bypass
Press the Select icon to enter the sensor bypass
screen.
Panel Status
Press the Listen icon to listen to the status of your
security system. Press Clear to clear the status.
Chime
Press the On/Off icon to set the chime feature
On/Off.
Note: This option may or may not appear depending
on panel programming.
Press to access the Status & Settings screen.
Special Chime
Press the On/Off icon to set the special chime
feature On/Off.
Note: This option may or may not appear depending
on panel programming.
Lights
Press Control to access the Light screen. From there
you can turn On/Off programmed lights.
Note: Has not been investigated by UL.
Door Locks
Press Control to access the Door Lock screen. From
there you can lock/unlock programmed door locks.
Note: Has not been investigated by UL.
Voice Volume
Press the arrows to adjust the speech volume level.
Beep Volume
Press the arrows to adjust the beep volume level.
Brightness
Press the arrows to adjust the screen’s brightness.
Arming errors
If you select an arming option on the Arm screen, and there is an
arming problem, an arming error message will appear at the
bottom of the screen, indicating what the problem is and how to
correct it. For example, you might see a message that indicates
that you need to close the front door.
Correct the problem as indicated or press Bypass. You will see the
arming countdown message at the bottom of the screen. You can
touch Cancel and enter your code to stop the arming process.
Simon XTi Installation Guide
5
Option
How to view
Option
How to view
Default Screen
Use this feature to set this panel’s screen saver
mode. Select “Blank” to have the screen and LED go
dark after a period of inactivity. Otherwise, the
default will be the Home screen and the screen will
always be lit. If AC power is lost, the screen will go
blank after 2 minutes of inactivity to maximize
battery life.
Note: The screen will automatically go blank at 2:00
am daily for 60 minutes.
Press the Timers icon to access the following timers
options:
Press the Show icon to enter the calibration screen.
This screen will allow you to recalibrate the touch
screen.
Calibration
•
Entry delay
•
Exit delay
•
No activity timeout
•
Audio phone test
•
Supervisory time
•
Alarm cancel window
•
RF timeout
•
Fail to open time
•
Fail to close time
Help
Press the Help icon to access the Help menu.
•
Siren timeout
Set Date/Time
Press Enter to set the date and time.
•
Unvacated premises
System Tests
Press Enter to perform a sensor test or system
download.
•
Smoke supervision
Programming
Press the Touchpad Options icon to access the
following options:
Press the Access Codes icon to change existing or
add new access codes.
•
•
•
Press the Security icon to turn downloader enable
on/off and to set the account number.
Press the System Options icon to access the
following system options:
Press the Phone numbers icon to change existing or
add new phone numbers.
Press the Phone Options icon to access the
following phone options:
•
•
•
•
•
•
•
Manual phone test
Fail to communicate
DTMF dialing
300 BPS enabled
Ring hang ring
Dialer delay
Call waiting code
•
RF jam detect
•
Demo mode
•
HW1 function
•
24 hour clock
Press the Siren Options icon to turn on/off the
following options:
•
•
•
•
•
•
•
•
Press the Sensors icon to access the learn sensor,
edit sensor, and delete sensor options.
Press the Reporting icon to access the following
reporting options:
•
•
•
•
•
•
•
•
•
•
•
•
Keyfob no delay
Panic alarms
Remote TP arming
Opening report
Closing report
Force armed report
AC power failure report
Panel low battery report
Sensor alarm restoral report
24 hour sensor tamper
Supervisory tamper report
No usage report
Swinger shutdown
Programming report
Fire alarm verification
Panel piezo beeps
Panel voice
Panel piezo alarm
Trouble beeps
Voice chime
HW siren supervision
Silent police panic
Alarm report verify
Press the Audio Verification icon to access the
following audio verification options:
•
•
•
•
•
•
•
•
Audio mode
Fire shutdown
Fire enabled AVM
Panic talk
VOX receiver gain
VOX microphone gain
VOX microphone gain range
Manual microphone gain
Press the System Tests icon to perform a sensor
test, communication test, or system download test.
Version
Displays the system’s firmware version, touch
screen version, and copyright information.
Access Programming screen
1.
6
From the Status & Settings screen, press the down arrow to
scroll to the Programming option.
Simon XTi Installation Guide
2.
Press Enter.
Sensors
3.
Enter the dealer or installer code (see Table 4 below) and
press OK.
These instructions describe how to add (learn) sensors, touchpads,
and other system devices into panel memory. The panel
recognizes a sensor when you press a sensor program icon, press
and release a tamper switch, press a sensor test button, or put a
sensor into alarm. Table 6 below describes the programming
method for each device.
Note: You have four seconds between number presses to
enter the code or you will be returned to the home screen.
Note: Do not remove the panel power within 30 seconds of exiting
program mode.
Table 4: Simon XTi programming codes
Code
Description
Dealer
code
You can use the dealer code to program all system functions,
including high-security options that are not accessible with the
installer code if it is different from the dealer code. Depending
on how the access code is set, the default dealer access code
is 654321, 54321, 4321 (factory default), or 321. This code can
be used for all programming.
Installer
code
Depending on how the access code is set, the default installer
code is 654321, 54321, 4321 (factory default), or 321. This code
is limited to changing all but the following: Dealer code, code
length, downloader code, phone lock, phone #1, phone #2,
phone 1 report mode, phone 2 report mode, HW1 function.
Note: If you are installing a sensor on a gun case, jewelry box, or a
similar case, and the sensor is active in level one, you must direct
bypass the sensor to avoid putting the panel into alarm when the
sensor and the magnet are separated.
Mounting Recommendations:
•
Where possible, install sensors within 100 feet (30 m) of the
receiver. While a transmitter and receiver combination may
have an open-air range of 500 feet (152 m) or more, the
environment at the installation site may have a significant
effect on operational range. Changing a sensor or receiver
location can improve wireless communication.
•
Avoid mounting sensors or receivers in areas where they will
be exposed to moisture or where the operating temperature
range will exceed the specified range (10 to 120 °F).
•
Avoid mounting the sensor or receiver in areas with a large
quantity of metal or electrical wiring. For example: within 1
meter of AC distribution panel (fuse box), HVAC duct work
•
Avoid mounting the sensor or receiver directly on metal.
•
The Simon XTi system should not be mounted within 3 meters
of any other RF equipment (RF music system transmitter,
wireless router/modem, etc.).
Access codes
Table 5 below describes the Access code menu programming
options.
Table 5: Access codes
Function
Default
Description
Dealer
code
4321
You can use the dealer code to program all
system options, including high-security options
that are not accessible with the installer code if
it is different from the dealer code. Changing the
dealer code to differ from the installer code will
prevent the installer from viewing certain fields.
If you change the dealer code and enter
program mode with the installer code, the
installer will no longer be able to see the
following: code length, downloader code, phone
lock, phone #1, phone #2, phone 1 report mode,
phone 2 report mode, HW1 function.
Note: Refer to specific sensor installation instructions for complete
operation and testing details.
Table 6: Device programming
Device
To program
Door/window
sensor
Press the button on the top of the sensor (cover
removed) or trip the tamper.
Motion sensor
Press the button on the back of the sensor (mounting
plate removed) or trip the tamper.
Trip the tamper, press the test button, remove the
detector from its base, or put the smoke detector into
alarm.
Installer
code
4321
You can use the installer code to program most
installer options, except for high-security dealer
options.
Master
code
1234
You can use the master code to arm/disarm the
system and to enter user programming and
bypass sensors.
Smoke detector
User
codes 1 to
8
Blank
You can use the user codes to arm/disarm the
system.
Hardwired sensor Separate the sensor from its magnet.
Duress
code
Blank
You can use the duress code in place of the
master or user code to cause a silent alarm.
Code
length
Four digits
Codes can be three to six digits long.
Simon XTi Installation Guide
CO alarm
Trip the wall tamper by removing the sensor body from
the mounting plate.
Simon XT talking
touch screen
1. Press the Settings icon.
2. Press the Down arrow until the Clear and Enroll icon
appears.
3. Press the Clear and Enroll icon. The touch screen
should indicate it is waiting for enrollment.
7
Device
To program
Simon XT talking
touchpad
Press the Lights off button on the touchpad six times in
rapid succession. On the sixth press, the touchpad
makes a longer beep.
Key fob
Press the lock and unlock buttons at the same time.
Note: While the sensor test is a valuable installation and service
tool, it only tests sensor operation for the current conditions. You
should perform a sensor test after any change in environment,
equipment, or programming.
Notify the central station you will be performing a test prior to
starting the test.
To learn (program) a sensor:
1.
From the Programming screen, enter the access code from
the codes listed in Table 5 on page 7. The display shows each
entered access code digit as a dot.
To test the sensors:
1.
Place all sensors in their secured (non alarm) state.
2.
Access the System Test screen through the Programming
Screen, and then press OK.
2.
Press OK. You are now in the programming screen.
3.
Press Sensors.
3.
Enter the dealer or installer code and press OK.
4.
Press Learn Sensor.
4.
Press Sensor Test.
5.
Trip the sensor (see Table 6 on page 7). The Edit Sensor screen
will appear. If no further action is required (change sensor
name, number, or group) proceed to step 8. To exit, press
Close repeatedly.
5.
All learned in sensors will be displayed on this screen. Press
the arrows to scroll through the pages.
6.
To change the sensor name, number, or sensor group press
the appropriate Edit icon and modify the value. To change
the sensor text, press the appropriate Edit icon, then choose
the item you would like to change.
7.
Press Save to keep the new sensor, or Cancel to abort
learning this sensor into the system (both of these choices will
return you to step 5).
8.
To exit, press Close repeatedly.
Test your sensors by tripping them one at a time. The panel
will display the number of transmissions received from
sensors you trip. See Table 7 below for specific instructions on
how to trip each sensor type.
The panel sounds beeps, and the display identifies the tripped
sensor and the number of RF packets received. Each beep
represents one RF packet. Count the number of beeps and
refer to Table 7 below for minimum requirements. The panel
displays Sn #, Name, and Rounds Detected (Packets). Scroll
through to make sure all sensor have been tested.
Sensor Naming
Table 7: Sensor tripping instructions
Please use the following guide when naming sensors:
Sensor
Instructions
Minimum
packets required
•
Hardwire contact
Open the hardwire contact.
1
Door/window
Open the secured door or
window.
6 of 8
Carbon
monoxide alarm
Press and hold the Test/Hush
button (approximately 5 seconds)
until the unit beeps two times,
and then release the button.
6 of 8
Glassbreak
Test with an appropriate glass
break sensor tester.
6 of 8
Motion sensor
Avoid the motion sensor field of
view for 5 minutes, and then
enter its view.
6 of 8
Smoke
Press and hold the test button
until the system sounds
transmission beeps.
6 of 8
Key fob
Press and hold the Lock and
Unlock buttons simultaneously
for 3 seconds.
6 of 8
Simon XT talking
touchpad
Press and hold the two
Emergency buttons
simultaneously for 3 seconds.
6 of 8
Sensor names must have the word “window” or “door” from
the text library to interact with the touch screen Door and
Windows icons on the Main screen.
•
On the Edit Sensor name screen in programming, default the
screen to list and not keypad. This gives the user the list of
possible sensor names.
•
The Motion icon is controlled by sensors that are
programmed into the following groups: 15, 17, 18, 20, 28, or
32.
•
The Property icon is controlled by the following sensors:
•
•
•
•
All sensors learned into Group 43.
Sensors that are not named “window” or “door”.
Sensors not learned into the Motion groups.
Sensors that are named keyfob, keychain or touchpad.
Sensor Testing
Test the sensors after all programming is completed and
whenever a sensor-related problem occurs.
8
Simon XTi Installation Guide
Sensor
Instructions
Simon XT talking
touch screen
For sensor testing a 1.0. touch
6 of 8
screen, press and hold the
Emergency icon for 5 seconds.
For sensor testing a 1.1 or greater
touch screen, press the Settings
(gear) icon, scroll down, and then
press the RF Test icon.
6.
Minimum
packets required
Press Close repeatedly to exit.
Sensor Test Failure
If sirens do not beep when a sensor is tripped, use an RF Sniffer
(60-401) test tool to verify that the sensor is transmitting. Constant
beeps from the RF Sniffer indicate a faulty sensor. Replace the
sensor.
If possible, locate sensors within 100 ft. (30 m) of the panel. While a
sensor may have a range of 500 ft. (152 m) or more out in the
open, the environment at the installation site can have a
significant effect on transmitter range. A change in sensor location
may help overcome adverse wireless conditions and can
potentially be accomplished by the following:
•
•
•
Reposition the sensor
Relocate the sensor
If necessary, replace the sensor
To reposition a sensor:
1.
Rotate the sensor and test for improved sensor
communications at 90 and 180 degrees from original
position.
2.
If poor communication persists, relocate the sensor.
To relocate a sensor:
•
Conduct sensor test whenever changes are made to the
installation environment that may impact RF performance
(For example: mirrors installed, metal backed wall paper,
addition of other RF equipment).
•
Sensor testing should be done before and after permanent
mounting.
Comm Testing
If Comm Test is not finished, it will continue to run even if you exit
program mode.
Note: Complete panel programming before performing comm
testing.
To perform a comm test:
1.
Enter the Status & Settings menu.
2.
Scroll until System Tests is listed, Press Enter.
3.
Enter your master code and press OK.
4.
Press Comm Test.
The panel displays if the comm test was successful or not.
Central station communication
After performing sensor tests, check that the system is reporting
alarms successfully to the central station.
Note: The communication with the central station test must be
done while NOT in programming mode.
To verify alarm reporting:
1.
Call the central station and tell the operator that you will be
testing the system.
1.
Test the sensor a few inches from the original position.
2.
Arm the system.
2.
Increase the distance from the original position and retest
until an acceptable location is found.
3.
3.
Mount the sensor in the new location.
Test an emergency panic icon and trip at least one sensor of
each type (fire, intrusion, etc.) to verify that the appropriate
alarms are working correctly. There is a 30 second delay.
4.
If no location is acceptable, replace the sensor.
4.
When you finish testing the system, call the central station to
verify that the alarms were received.
To replace a sensor:
1.
Test a known good sensor at the same location.
Cleaning the touch screen
2.
If the transmission beeps remain below the minimum level,
avoid mounting a sensor at that location.
If necessary, use a soft cloth to clear smudges on the touch
screen. Do not use glass cleaner on the touch screen.
3.
If the known-good sensor functions, contact UTC Fire &
Security for repair or replacement of the problem sensor.
Disposal
Sensor Testing Notes:
•
Dispose of all equipment is accordance with local requirements.
Conduct sensor test in all possible environmental conditions
(For example: interior doors open and closed, HVAC system
on and off, wireless music system turned on and off).
Simon XTi Installation Guide
9
Specifications
Power
Household fire warning system (UL 985), basic system plus the
following:
9 VAC, 60 Hz, 25 VA transformer minimum
Rechargeable battery: 6.0 VDC, 2.1 Ah NIMH.
Maximum battery charging current is 120 mA.
Once the battery reaches a low battery condition,
a trouble signal will be annunciated, indicating
that the battery may no longer support a full
alarm load.
When fully charged, the battery will operate the
panel without AC power for 24 hours with the
panel in a normal, standby condition, followed by
5 minutes in full alarm condition (including the
maximum specified auxiliary load of 250 mA).
Radio frequency
319.5 MHz
Storage temperature
-29 to 140ºF (-34 to 60ºC) without battery
14 to 86ºF (-10 to 30ºC) with battery one year
shelf life
Operating
temperature
32 to 120ºF (0 to 49ºC)
Maximum humidity
85% relative humidity, noncondensing
Auxiliary power
Unregulated 4.0 to 12.3 VDC, with a maximum of
250 mA
•
•
•
•
•
•
•
•
Wireless smoke sensor 60-848-02-95, TX-6010-01-1 learned
into sensor group 26.
Panel piezo beeps turned on
Control panel alarms set to on
Siren timeout set to 4 minutes or more
Trouble beeps set to on
RF jam detect set to on
Hardwired siren supervision set to on
Smoke supervision set to on
UL 1635 digital alarm communicator system the following settings
are required only if the system is set up for central station
reporting:
•
•
•
•
•
•
•
Phone mode 1 set to “All SIA” or “All CID”
Automatic phone test set to 001
RF timeout set to 4 hours
AC power failure report set to on
CPU low battery report set to on
Fail to communicate set to on
Entry delay plus the dialer delay must not exceed 60 seconds
Regulatory information
SIA system requirements
Some installation may require configurations dictated by
city/state codes, insurance, or Underwriter’s Laboratories (UL). This
section describes the various component and configuration
listings.
Verified to SIA CP-01-2007 by ETL, basic system, plus if multiple
annunciations are required, use hardwired siren 13-046.
Basic system:
•
•
•
Control panel: Backup battery 6 V 2.1 Ah (34-070)
Standard Class 2, 9 VAC, 25 VA power transformer (UTC Fire &
Security part 22-155) or Standard, Class 2, 9 VAC, 30 VA (UTC
Fire & Security part 22-153).
Hardwired siren (13-374)
Household burglary alarm system unit (UL 1023), basic system
plus the following:
•
•
•
•
•
•
•
•
•
•
•
•
•
10
Hardwired magnetic contact (1038T) or wireless learn mode
door/window sensor (60-670-95R or
60-362N-10-319.5 or 60-362N-11-319.5)
Panel piezo beeps set to on
Entry delay set to 45 seconds or less
Exit delay set to 60 seconds or less
RF time-out set to 24 hours
Control panel alarms turned on
Auto arm set to on
Siren timeout set to 5 minutes or more
Trouble beeps set to on
RF jam detect set to on
Hardwired siren supervision set to on
Exit extension set to off
Quick exit set to off
Note: For UL 1635 installations, entry delay plus dialer abort delay
must not exceed 60 seconds.
Table 8 below describes programming requirements to meet
ANSI-SIA CP-01.
Table 8: SIA setting requirements
Function
Default setting
Required setting
Entry delay
30 seconds
30 to 240 seconds
Exit delay
60 seconds
45 to 240 seconds
Dialer delay
30 seconds
15 to 45 seconds
Auto arm
On
On
Unvacated premises
On
On
Call waiting
Off
On if reporting to
central station and
customer has call
waiting service
Alarm cancel window
6 minutes
6 to 255 minutes, Off
System test
Enabled
Enabled
Communication test
Enabled
Enabled
Exit extension
On
On
Swinger shutdown
On (one trip)
On (one trip)
Fire alarm verify
Off
On
Simon XTi Installation Guide
Function
Default setting
Required setting
Duress/panic code
Disabled
Disabled
Cross zone
Disabled
Disabled for zones with
high probability of false
alarms
Table 9 below describes nonprogrammable (hard-coded) system
operation, as required to meet ANSI-SIA CP-01.
Table 9: Nonprogrammable system operation
Function
Operation
Silent exit
All annunciators enabled
Remote arming exit time and
progress annunciation
All annunciators enabled
Abort annunciation
Enabled
Cancel report annunciation
Enabled
Recent closing
Enabled (2-minute window)
Exit error
Enabled
Restoration of power
Panel resumes operation in same
arming state and disregards alarm
signals from sensors for the first 60
seconds after power restoration
Cancel alarm
Enter code only
Central station reporting
Note: The panel shall not be set or programmed to place a call to
a police station number that has not been specifically assigned by
that police station for such service.
Caution: If call waiting is used on a non-call waiting line,
successful connection to the central station may be prevented.
The panel has been tested with the following central station
receivers using SIA and Contact ID reporting formats:
Before beginning installation, installers must verify that the central
station is equipped with the following receivers:
•
•
•
Residential burglary alarm system unit (ORD-C1023-1974): basic
system as described for UL 1023 listed installations plus:
•
•
Hardwired magnetic contact (1038T) or wireless learn mode
door/window sensor (60-670)
Siren timeout set to six minutes or more
Residential fire warning system control unit (ULC-S545-M89): basic
system as described for UL 985 listed installations plus:
•
•
Wireless smoke sensor 60-848-02-95, TX-6010-01-1 learned
into sensor group 26
Siren timeout set to six minutes or more
FCC compliance
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
FCC Part 15 registration number: B4Z-910C-SIMON
IC: 1175C-910CSIMO
This Class B digital apparatus complies with Canadian ICES-001.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Part 68. This equipment complies with Part 68 of the FCC rules and
the requirements adopted by ACTA.
FCC registration number: US: B4ZAK02B55910
Canada: 1175C-910CSIXT
Ranger Equivalence 0.2B
Load Number 0.2
Radionics D6600 central station receiver
Sur-Gard central station receiver with models SG-DRL2A and
SG-CPM2
CS5000 digital alarm communicator receiver
UL Canada listed installations
This section describes the requirements for CUL (UL Canada) listed
installations.
Canadian standards CSA certified accessories:
•
Standard Class 2, 9 VAC, 30 VA power transformer (UTC Fire &
Security model 22-153-CN) or Standard Class 2, 9 VAC, 25 VA,
(UTC Fire & Security model 22-155-CN).
Simon XTi Installation Guide
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising