WARNING Choosing Power Sources To use the player on AC power source (mains) Tip Connect the supplied mains lead to the AC IN jack. For customers supplied with an AC plug adaptor, use it if the plug of the mains lead does not match your mains. Notes • To use the player on batteries, disconnect the mains lead from the player. • Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Radio CassetteCorder Operating Instructions To prevent fire or shock hazard, do not expose the player to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the appliance. The FUNCTION selector is located at the top panel. When you turn on the player, the OPR/BATT indicator lights up. 1 to AC IN 2 On safety/power sources • Should any solid object or liquid fall into the player, unplug the player and have it checked by qualified personnel before operating it any further. • For AC operation, check that the player’s operating voltage is identical with your local power supply (see “Specifications”) and use the supplied mains lead; do not use any other type. The voltage selector is located at the rear of the player. • The player is not disconnected from the AC power source (mains) as long as it is connected to the mains, even if the player itself has been turned off. • For battery operation, use six R20 (size D) batteries. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, power consumption, etc., is located on the bottom. On placement/operation • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and to prolong the life of its components. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. • If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. to the mains CFS-B7SJMK2 To use the player on batteries Insert six R20 (size D) batteries (not supplied) into the battery compartment. Sony Corporation © 1999 Printed in Japan 3-865-191-53(1) To adjust the voltage Be sure to set the VOLTAGE SELECTOR (at the rear) to your local power supply. Precautions 220240V 110127V VOLTAGE SELECTOR Troubleshooting Specifications There is no audio. • Connect the mains lead securely. • Insert the batteries properly. • Replace all the batteries if they are weak. • Unplug the headphones. • Adjust the volume. • Set FUNCTION to the position you want to operate. Cassette cannot be inserted. • Insert the cassette properly. • Press p6 STOP/EJECT to release. The r REC button does not function. • No cassette in the tape compartment. • Make sure the safety tab on the cassette is in place. Poor playback, recording or erasing quality. • Dirty heads. Clean the unit (as shown) with a cotton swab slightly moistened with cleaning fluid or alcohol. • Demagnetize the heads and all metal parts in the tape path with a commercially available head demagnetizer. Pinch roller Erase head Record/ playback head Capstan Cotton swab • Frequency range FM: Saudi Arabia 87.6–107 MHz Other countries 87.6–108 MHz MW: 530–1,605 kHz SW1: 2.3–7 MHz SW2: 7–22 MHz • Aerials FM/SW: Telescopic aerial MW: Built-in ferrite bar • Recording system 2–track, 4–channel stereo • Frequency response 70–10,000 Hz • Speakers Full range: 10 cm (4 inches) dia., 2.8 ohms cone type x 2 • Output Headphones jack (stereo minijack), for 16–68 ohms impedance headphones • Maximum Power output 2.5 W+2.5 W • Battery life FM Recording: Sony R20P: Approx. 16 hours/Sony LR20 alkaline: Approx. 36 hours Playback: Sony R20P: Approx. 8 hours/Sony LR20 alkaline: Approx. 21 hours • Power requirements 110–127 V/220–240 V AC selectable, 50/60 Hz 9V DC, six R20 (size D) batteries • Power consumption AC 14W • Dimensions Approx. 500 x 155 x 164 mm (w/h/d) ( 19 3/4 x 6 1/8 x 6 1/2 inches) incl. projecting parts and controls, not incl. handle • Mass Approx. 2.7 kg (5 lb 15 oz) not incl. batteries • Supplied accessory Mains lead (1) Design and specifications are subject to change without notice. Use TYPE I (normal) tape only. Location of controls HYPER TREBLE MEGA BASS VOLUME 2 FUNCTION Listening to the radio 1 Set FUNCTION to RADIO. Playing a tape 1 FUNCTION OPR/BATT MIC Set FUNCTION to TAPE (RADIO OFF) . FUNCTION Use TYPE I (normal) tape only. Recording 1 To record from the radio Tune to the station you want. To record from the built-in microphone (MIC) Set FUNCTION to TAPE (RADIO OFF) . RADIO RADIO To Press stop recording p6 STOP/EJECT pause recording P PAUSE Press this button again to resume recording. Tips TAPE (RADIO OFF) 2 PAUSE STOP/EJECT PLAY TAPE (RADIO OFF) Set BAND to the band you want. 2 2 With the side you want to record on facing you. Insert a recorded tape. FM SW1 SW2 MW STOP/EJECT BAND DIR 3 STOP/EJECT Notes on cassettes Tune to the station you want. FINE TUNE TUNE 3 3 Press 9 PLAY. PLAY To tune in an SW band, use FINE TUNE for better reception. • Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the tab hole with adhesive tape. Make sure the FWDª indicator is highlighted. If the REV· indicator is highlighted instead, press the DIR lever to switch the highlight to FWDª. FINE TUNE DIR TUNE MODE To turn off the radio Set FUNCTION to TAPE (RADIO OFF) . FWD/REV indicator To improve broadcast reception Reorient the aerial for FM. Reorient the player itself for MW. For SW, pull the aerial vertically. To Press stop playback p6 STOP/EJECT fast-forward or rewind the tape 0 or ) pause playback P PAUSE Press this button again to resume playback. switch playback to the opposite side FM DIR FWD REV Note The player cannot record from the reverse side of the tape (REV·). 4 Press r REC. 9PLAY is depressed automatically. MW PLAY To adjust the bass and treble Turn MEGA BASS toward MAX to enhance the low tones, and turn HYPER TREBLE toward MAX to enhance the treble tones. Tips SW Tips • To listen through headphones, connect the headphones to the 2 (headphones) jack. •For best results, place the player away from a TV. Notes • When r REC is pressed with MODE set to d , the MODE setting switches to A automatically. • When recording from the built-in microphone, the sound cannot be monitored through the headphones. With the side you want to play facing you. REC FWD ONLY BAND • For best results, use the AC power source (mains). • Adjusting the volume or audio emphasis will not affect the recording level. Insert a blank tape. • The FWD/REV indicator shows the side being played during playback: FWDª (the side facing you), or REV· (the reverse side). • Set MODE to A to play either side, or d to play both sides repeatedly. REC FWD ONLY Side A Tab for side B Tab for side A • The use of cassettes with more than 90 minutes of play time is not recommended except for long, continuous recording or playback.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project