DG-CM3230 QIG - Smartlink Network Systems Ltd

DG-CM3230 QIG - Smartlink Network Systems Ltd
DG-CM3230 Quick Installation Guide
DG-CM3230 Quick Installation Guide
Safety
These instructions are proposed to ensure that user can
make use of the camera correctly to avoid danger or
property loss. The precaution measure is divided into
“Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the
warnings is neglected.
Cautions: Injury or equipment damage may occur if any of
the cautions is neglected.
DG-CM3230
Weatherproof 720P AHD bullet camera with IR LED
Quick Installation Guide
V1.0
2015-04-06
As our products undergo continuous development the specifications are subject to change without prior notice
Copyright
Copyright 2015 by Smartlink Network Systems Ltd. All
rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer
language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this
company.
Trademarks
DIGISOLTM is a trademark of Smartlink Network Systems
Ltd. All other trademarks are the property of the respective
manufacturers.
Warnings
1. While using this product, user must strictly comply
with the electrical safety regulations of the nation
and region.
2. Input voltage should meet both the Safety Extra
Low Voltage and the Limited Power Source with
DC 12V according to the IEC60950 - 1 standard.
Please refer to technical specifications for more
detailed information.
3. Do not connect several devices to one power
adapter as adapter overload may cause over-heat
or fire hazard.
4. Please make sure that the plug is firmly connected
to the power socket.
5. When the product is mounted on the wall or ceiling,
the device shall be firmly fixed.
6. If you get any signs of smoke, odor or noise from
the device, turn off the power at once, unplug the
power cable, and please contact the service
center.
7. If the product does not function properly, please
contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself.
(DIGISOL shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance.)
DG-CM3230 Quick Installation Guide
Cautions
1. Ensure that the power supply voltage is right
before using the camera.
2. Do not drop the camera or subject it to physical
shock.
3. Do not touch CCD/CMOS modules with fingers. If
cleaning is necessary, then use a clean cloth with
a bit of ethanol and wipe it gently. If the camera
won’t be used for an extended period, please turn
on the lens cap to protect the CCD/CMOS from
dirt.
4. Do not place the camera near sun or extra bright
places. A blooming or smear may occur otherwise
(which is not a malfunction however), affecting the
endurance of CCD/CMOS at the same time.
5. Do not place the camera in extremely hot, cold,
dusty or damp locations, and do not expose it to
high electromagnetism radiation.
6. To avoid heat accumulation, good ventilation is
required for operating environment.
7. Keep the camera away from liquid while in use.
Package Contents
The following items should be present in your package:
1. DG-CM3230 Weatherproof Bullet Camera with IR LED
2. Quick Installation Guide
3. Mounting Accessories (One Allen key, three Nylon
anchors & three screws)
Make sure that the package contains above items. If any
of the listed items is damaged or missing, please contact
your retailer immediately.
Product Overview
Thank you for purchasing DG-CM3230 Weatherproof
Bullet Camera with IR LED. This Camera has 720P
Resolution and built-in IR LED. It can cover a range of
30m. It is an ideal solution for outdoor CCTV surveillance
application.
Rev. 1.0
Copyright All rights reserved
DG-CM3230 Quick Installation Guide
Key Features
• 1/4" Color CMOS Sensor
DG-CM3230 Quick Installation Guide
NOTES:
1.
• 720P Resolution
• IR Cut Filter
• 36PCS IR LED
• 3.6mm Fixed lens
3.
Do not expose the camera to an eroding
environment.
4.
Pay attention to keep the surface of the lens clean.
The quality of the image can degrade if the
surface is scratched.
5.
Do not expose the camera to moisture that
exceeds 85% for a long time.
• BLC, AWB support
Installation
Following is an installation setup diagram. Power On the
camera using a 12V DC Power adapter and connect the
BNC Video out to a TV/LCD or to a DVR.
Do not attempt to open the cover unless you are
authorized to do so.
Handle with care.
• Weatherproof IR Camera with 3-Axis Bracket
• IP66 Compliant
Technical Specifications
2.
• Up to 30m IR Distance
DG-CM3230 Quick Installation Guide
6.
Please do not use strong corrosive cleaner while
cleaning the surface of the camera.
7.
Avoid focusing on the sun or a powerful light
source directly.
8.
Avoid working in spotlight or a powerful light
environment.
9.
Set the power voltage as mentioned in the
technical spec sheet below.
10.
Use the camera within the temperature between
-10 ~ +50.
Parameter
Specification/Description
Image Sensor
TV System
CMOS
PAL / NTSC
PAL:1280x720@25fps
NTSC:1280x720@30fps
1280 x 720
Color 1.0Lux/F1.2,B/W 0.1Lux/F1.2
Effective Pixels
Resolution
Minimum illumination
Electronic Shutter
Speed
Video output
LED & IR Distance
Day & Night Mode
White Balance
Black light
Compensation
Lens
Operating
Temperature
Storage
Temperature
Dimensions
Power
Weight
4/25-1/45,000s
1CH Video output, Support CVBS , AHD
36PCS IR LED, 30m IR Distance
Auto
Auto
Auto
3.6mm Fixed lens
-10°C ~ +50°C,RH80%Max
-20°C ~ +60°C,RH90%Max
14.6 x 6.5 cms
12V DC
0.33 kg
This product comes with one year warranty. For further details
about warranty policy and Product Registration, please visit
support section of www.digisol.com
Rev. 1.0
Copyright All rights reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising