Agilent PNA Family Microwave Network Analyzers

Agilent PNA Family Microwave Network Analyzers
Agilent
PNA Family
Microwave Network Analyzers
Configuration Guide
This configuration guide describes standard
configurations, options, accessories, upgrade kits
and compatible peripherals for the PNA Family
microwave network analyzers. This guide should
be used with the Agilent PNA Family data sheets for
a complete description of these analyzers.
PNA-X Series
N5249A
N5241A
N5242A
N5244A
N5245A
N5247A
PNA Series
N5221A N5222A N5224A N5225A N5227A 10 MHz to 8.5 GHz
10 MHz to 13.5 GHz
10 MHz to 26.5 GHz
10 MHz to 43.5 GHz
10 MHz to 50 GHz
10 MHz to 67 GHz
10 MHz to 13.5 GHz
10 MHz to 26.5 GHz
10 MHz to 43.5 GHz
10 MHz to 50 GHz
10 MHz to 67 GHz
PNA-L Series
N5239A N5231A N5232A N5234A N5235A 300 kHz to 8.5 GHz
300 kHz to 13.5 GHz
300 kHz to 20 GHz
10 MHz to 43.5 GHz
10 MHz to 50 GHz
Table of Contents
PNA Family Network Analyzer Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Application options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessories, calibration options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PNA-X Series test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . 7
PNA Series test set and power configuration options. . . . . . . . . . . . . . . . . . . . . . . . . 9
PNA-L Series test set and power configuration options . . . . . . . . . . . . . . . . . . . . . . . 11
PNA Family Application Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Measurement applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Noise figure options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pulse, antenna, mm-wave. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
PNA Family Network Analyzer Upgrade Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Frequency, test ports, test set and power configurations. . . . . . . . . . . . . . . . . . . . . . . 18
Application options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Upgrade paths. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Material measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Signal integrity measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Multiport measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Millimeter-wave measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Measurement Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Calibration kits, cables, adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
For devices with 1.0 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
For devices with 1.85 mm connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
For devices with 2.4 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
For devices with K (2.92 mm) connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
For devices with 3.5 mm or SMA connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
For devices with Type-N connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
For devices with 7 mm connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
For devices with waveguide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Verification kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Spare drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Power meters and sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Comb generators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Equipment rack accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Monitors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Interface cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2
Agilent offers the following options for all PNA Family network analyzers
Documentation
Certification options
□Commercial calibration certification with test data (Option UK6)
The PNA Series instruments are equipped with an Online Help system
available within the instrument in English only. All PNA documentation is available on the web: www.na.tm.agilent.com/pna
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, calibration
certificate, and data report. Conforms to ISO 9001.
Calibration Software Licenses
□Perpetual license for built-in performance test software for □ISO 17025 compliant calibration (Option 1A7)
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes calibration label, ISO 17025
calibration certificate, and data report, measurement uncertainties
and guardbands on all customer specifications. Conforms to ISO
17025 and ISO 9001.
Agilent inclusive cal (Option 897)
Adds built-in performance testing and calibration software for self-
maintainers. Requires additional equipment. See the analyzer’s Service Guide for more information on equipment required.
□Perpetual license for built-in performance test software for □ANSI Z540 compliant calibration (Option A6J)
Complete set of measurements which tests unit to manufacturer’s
published specifications. Includes pre- and post-adjustment data
with measurement uncertainty information compliant to the
ANSI/NCSL Z540 standard.
Warranty and service
3- and 5-year warranty and service plans are available at the time
of instrument purchase. Standard warranty is 3 years.
3
Standards compliant cal (Option 898)
Adds built-in performance testing and calibration software for self-
maintainers. Requires additional equipment. See the analyzer’s Service Guide for more information on equipment required.
PNA Family Network Analyzer Configurations
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Test set and power configuration options
Choose one test set and power configuration option. Option 2xx indicates two test ports. Option 4xx indicates four test ports. To add options to a product, order
the corresponding item number (N52xxA-xxx).
Description
Configurable
Test Set
Source
Receiver
Attenuators Attenuators
Bias-tees
Internal
Second
Source
Internal
Combiner
Mechanical
Switches
Additional Information
PNA-X Series
Option 200
●
Option 200, H85,
2851
●
●
●
Option 200, 219
●
●
●
Option 200, H85,
285, 2241
●
●
●
Option 200, 219,
224
●
●
●
Option 400
●
Option 400, H85,
4851
●
●
●
Option 400, 419
●
●
●
Option 400, H85,
485, 4231
●
●
●
Option 400, 419,
423
●
●
●
Not available on 67 GHz
model
●
●
●
●
●
●
●
Requires Option 080
Not available on 67 GHz
model
●
●
●
Requires Option 080
●
Option 080 recommended
●
Option 080 recommended
Not available on 67 GHz
model
●
Option 080 recommended
●
●
●
Requires Option 080
Not available on 67 GHz
model
●
●
●
Requires Option 080
PNA Series
Option 200
Option 201
●
Option 210
2-port metrology option
Option 217
●
●
●
Option 219
●
●
●
Not available on 67 GHz model
●
Option 400
Option 401
●
Option 410
Option 417
●
●
●
Option 419
●
●
●
●
●
●
●
●
●
Option 080 recommended
●
Option 080 recommended
●
4-port metrology option
●
Option 080 recommended
Not available on 67 GHz
model
●
Option 080 recommended
PNA-L Series
Option 200
Option 216
Available on only N5231A/2A
Option 400
Option 4162
Available on only N5231A/2A
1. Order special model N524xAS instead of N524xA. Order N524xA-xxx items for other standard options. Option H85 requires Option 285 or 485 which includes the extended power range of Option 219 or 419; therefore these options cannot be combined.
2. Adds one source attenuator to be shared with all test ports.
4
PNA Family Network Analyzer Configurations (continued)
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Application options
To add options to a product, order the corresponding item number (N52xxA-xxx).
Description
For PNA-X Series
For PNA Series
For PNA-L Series
Additional Information
Time-domain measurements
N524xA-010
N522xA-010
N523xA-010
Noise figure measurements
using standard receivers1
N524xA-028
N522xA-028
n/a
Requires Option 080. For measuring frequency
converters, requires Option 082 or 083. Not available
with N522xA-200, -210, -400 and -410
Fully-corrected noise figure
measurements1
N524xA-029
n/a
n/a
Requires Option 080 and for N5241/42/49A, one of
Options 219, 224, 419, 423 or H85. For N5244/45/47A,
requires Option 224 or 423. On N5247A, noise receivers work up to 50 GHz only. For measuring frequency
converters, requires Option 082 or 083.
Frequency offset2
N524xA-080
N522xA-080
N523xA-080
Scalar-calibrated converter
measurements3
N524xA-082
N522xA-082
N523xA-082
Requires Option 080
Vector- and scalar-calibrated
converter measurements3, 4
N524xA-083
N522xA-083
n/a
Requires Option 080
Embedded LO measurements
N524xA-084
N522xA-084
n/a
Requires Option 082 or Option 083. Also works with
Options 028, 029, 086 and 087
Gain compression application
N524xA-086
N522xA-086
n/a
For measuring frequency converters, requires
Option 082 or 083
Intermodulation distortion
application5
N524xA-087
N522xA-087
n/a
Requires Option 080
For measuring frequency converters, requires Option
082 or 083. Not available with N522xA-200, -210, -400
and -410
Source phase control
N524xA-088
N522xA-088
n/a
Not available with N522xA-200 and -210
Ambient temperature CalPod
option
N524xA-301
N522xA-301
N523xA-301
Application firmware for use with CalPod calibration
refresh modules
Temperature characterized and
TVAC CalPod operation
N524xA-302
N522xA-302
N523xA-302
Application firmware for use with CalPod calibration
refresh modules
Integrated true-mode stimulus
application
N524xA-460
N522xA-460
n/a
Requires one of Options 400, 401, 410, 417, 419 or 423
N-port capabilities6
N524xA-5517
N522xA-551
N523xA-551
Measurement application
1.
2.
3.
4.
5.
6.
7.
Not available with N522xA-200, -210, -400 and -410,
and N523xA-200 and -400
For N522xA and N5241/42/49A, vector-noise-corrected measurements require an ECal for use as an impedance tuner. For N5244/45/47A with Option 029,
an internal tuner is included. For calibration, Option 028 requires a power meter, and Option 029 requires either a power meter or a 346-series noise source
(Agilent 346C or 346C-K01 recommended). All options require a power meter for measuring mixers and converters.
Option 080 is required to configure an external source using External Device Configuration dialog.
Option 082 is a subset of Option 083; therefore, they cannot be ordered together.
A configurable test set is required for VMC measurements (to connect a reference mixer) or for SMC+Phase measurements using the comb-generatorbased calibration. When ordered with N522xA-200, -210, -400 and -410, Option 083 adds phase and delay measurements only by using SMC+Phase with a
calibration mixer.
Option 087 can be ordered without N524xA-224 or N524xA-423, but may require external equipment such as a signal generator and a combiner. Refer to
page 13 for more details.
When ordering a test set, select an appropriate interface kit. Refer to page 22 Multiport Measurements section for more details.
When configuring N524xA as a multiport analyzer using Option 551 and a multiport test set, the combiner feature of Option 224 or 423 is temporarily disabled. When configuring N524xA as a standalone analyzer, the combiner feature is enabled.
5
PNA Family Network Analyzer Configurations (continued)
PNA-X Series
PNA Series
N5249A 10 MHz to 8.5 GHz
N5241A 10 MHz to 13.5 GHz
N5242A 10 MHz to 26.5 GHz
N5244A 10 MHz to 43.5 GHz
N5245A 10 MHz to 50 GHz
N5247A 10 MHz to 67 GHz
PNA-L Series
N5221A 10 MHz to 13.5 GHz
N5222A 10 MHz to 26.5 GHz
N5224A 10 MHz to 43.5 GHz
N5225A 10 MHz to 50 GHz
N5227A 10 MHz to 67 GHz
N5239A 300 kHz to 8.5 GHz
N5231A 300 kHz to 13.5 GHz
N5232A 300 kHz to 20 GHz
N5234A 10 MHz to 43.5 GHz
N5235A 10 MHz to 50 GHz
Application options (continued)
To add options to a product, order the corresponding item number (N52xxA-xxx).
Description
For PNA-X Series
For PNA Series
For PNA-L Series
Pulsed-RF measurements
N524xA-008
N522xA-008
n/a
Add IF inputs
N524xA-020
N522xA-020
n/a
Add pulse modulator to internal
1st source
N524xA-021
N522xA-021
n/a
Add pulse modulator to internal
2nd source
N524xA-022
N522xA-022
n/a
Add four internal pulse generators
N524xA-025
N522xA-025
n/a
Fast CW sweep
N524xA-118
N522xA-118
n/a
Additional Information
Pulse, antenna, mm-wave
Requires Option 025
Requires one of Option 224, 400, 401, 417, 419, or 423
Nonlinear vector network analysis1
Nonlinear component
characterization
N524xA-510
n/a
n/a
Requires Options 419 and 080, or 400, H85 and 080
Nonlinear X-parameters2
N524xA-514
n/a
n/a
Requires Options 423 and 510, requires MXG or PSG
except 10 MHz tone-spacing
Nonlinear pulse envelope
domain
N524xA-518
n/a
n/a
Requires Options 021, 025 and 510
Arbitrary load-inpedance
X-parameters
N524xA-520
n/a
n/a
Requires Option 514, requires MXG or PSG except
10 MHz tone-spacing
Accessories, calibration options
To add options to a product, order the corresponding item number (N52xxA-xxx).
Description
For PNA-X Series
For PNA Series
For PNA-L Series
Rack mount kit for use without
handles
N524xA-1CM
N522xA-1CM
N523xA-1CM
Rack mount kit for use with handles
N524xA-1CP
N522xA-1CP
N523xA-1CP
N1966A
N1966A
n/a
Perpetual license for built-in
performance test software for
Agilent inclusive calibration3
N524xA-897
N522xA-897
N523xA-897
Perpetual license for built-in
performance test software for
standard compliant calibration3
N524xA-898
N522xA-898
N523xA-898
ISO 17025 compliant calibration
N524xA-1A7
N522xA-1A7
N523xA-1A7
Commercial calibration certificate
with test data
N524xA-UK6
N522xA-UK6
N523xA-UK6
ANSI Z540 compliant calibration
N524xA-A6J
N522xA-A6J
N523xA-A6J
Additional Information
Accessories
Pulse I/O adapter
Calibration software
Calibration documentation
1.
2.
3.
To configure NVNA, requires two comb generators with power supplies, Agilent calibration kits (mechanical or ECal), power meter and sensor or USB power
sensor. Requires EXG, MXG or PSG for X-parameter extraction (PNA-X 10 MHz reference output can be used for 10 MHz tone-spacing applications).
X-parameters is a trademark of Agilent Technologies.
Additional hardware required. Please refer to the analyzer’s Service Guide for required service test equipment.
6
PNA-X Series test set and power configuration options
□ Extended power range and bias-tees (Option 219)
The PNA-X is an integrated vector network analyzer featuring a
built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a solid-state drive, USB interfaces, and
a 10.4” LCD touch screen display. The N5241A, N5242A, and
N5249A have 50 ohm, ruggedized 3.5 mm (m) test ports. The
N5244A and the N5245A have 50 ohm, ruggedized 2.4 mm (m) test
ports. The N5247A has 50 ohm, ruggedized 1.85 mm (m) test
ports. Included with each instrument is a mouse, keyboard (U.S.
style), a 3-year return-to-Agilent service warranty, and one day of
on-site productivity assistance (PS-S20-PNA).
Adds to the standard test set one 65 dB for N5241/42/49A, 60 dB for N5244/45A, and 50 dB for N5247A source attenuator (set
table in 5 dB increments for N5241/42/49A and 10 dB increments for N5244/45/47A), one 35 dB receiver attenuator (settable in 5 dB increments) for N5241/42/44/45/49A and 50 dB receiver attenuator (settable in 10 dB increments) for N5247A, and one bias-tee to each test port. Option 219 requires Option 200.
IF inputs
rear panel
R
Source 1
OUT 1
A test set and power configuration option is mandatory, choose
one of the following:
A
B
C
D
OUT 2
Pulse
modulator
□2-port standard test set and power range (Option 200)
The standard 2-port test set comes with six front-panel access loops. The loops provide access to the signal path between
(a) the source output and the reference receiver, (b) the source output and directional coupler thru arm and (c) the coupled arm of the directional coupler and the port receiver. The standard test set also includes a solid-state internal RF transfer switch in the R1 reference-receiver path.
R2
LO
A
B
To receivers
35 dB
65 dB
65 dB
Test port 1
35
dB
Test port 2
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
□ Add an internal second source, a combiner and mechanical
D
OUT 2
Pulse
modulator
Pulse generators
R1
R2
LO
A
B
To receivers
Test port 1
Test port 2
□High-power configurable and extended power range
Pulse generators
R1
(N524xAS Option H85/285)
With extended power range and bias-tees (Option 219), the internal bias-tees limit the maximum test port input power to +30 dBm. The N524xAS Option H85/285 removes the bias-tees between the source attenuators and the test port couplers. This extends the maximum port power that the analyzer can safely handle to +43 dBm. Selecting Option
H85/285 adds internal attenuators and cables. The N524xAS Option H85/285 and Option 219 can not be ordered together. Option H85/285 is not available for the N5247A. When ordering, select N524xAS then add items N524xAS-H85, N524xAS-285 and N524xA-200.
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
A
35 dB
65 dB
Test port 1
To receivers
R2
B
65 dB
Test port 2
J10
J9
J8
J7
J6
J5
RF
OUT
LO
OUT
J2
R
OUT 1
Source 1
OUT 1
OUT 2
To receivers
Pulse
modulator
OUT 2
35 dB
7
J1
A B R1 R2
LO
Source 2
Pulse
modulator
R1
R2
Pulse generators
A
B
1
2
3
4
35 dB
Test port 1
LO
IF inputs
J11
65 dB
OUT 2
Pulse generators
rear panel
D
Pulse
modulator
R1
switches to 2-port analyzer (Option 224)
Available with 2-port model only, this option adds an internal
second source, a combiner and mechanical switches. The
internal second source provides an additional signal (fixed or
swept) for two-tone third-order-intercept (TOI) and intermodu-
lation testing of amplifiers, or it can be used as a fast swept-
LO signal for fixed-IF testing of mixers and converters. The mechanical switches provide increased flexibility by having rear panel access (front panel access for N5247A Source 1 and
2 Out 1) to signal paths for advanced applications. Access to the second source is available through two output connectors on the front panel. Requires Options 200, 219 and 080.
65 dB
Source 2
Output 1
Source 2
Output 2
Test port 2
35 dB
PNA-X Series test set and power configuration options (continued)
□ 4-port standard test set, power range and an internal second □ Extended power range and bias-tees (Option 419)
source (Option 400)
The standard 4-port test set comes with 12 front-panel access loops and a built-in second source. The loops pro- vide access to the signal path between (a) the source output and the refer-
ence receiver, (b) the source output and directional coupler thru arm and (c) the coupled arm of the directional coupler and the port receiver. The inter- nal second source provides an additional signal (fixed or swept) for two-tone third-order-inter-
cept (TOI) and intermodulation testing of amplifiers, or it can be used as a fast swept-LO signal for fixed-IF testing of mixers and converters. With two sources, source 1 is accessible through test ports 1 and 2, and source 2 is accessible through test ports 3 and 4. The standard test set also includes a solid-
state internal RF transfer switch in the R1 reference-receiver path. Option 080 is recommended.
Adds to the standard test set one 65 dB for N5241/42/49A, 60 dB for N5244/45A, and 50 dB for N5247A source attenuator (settable in 5 dB increments for N5241/42/49A and 10 dB increments for N5244/45/47A), one 35 dB receiver attenuator (settable in 5 dB increments) for N5241/42/44/45/49A and 50 dB receiver attenua
tor (settable in 10 dB increments) for N5247A, and one bias-tee to each test port. Option 419 requires Option 400.
R
Source 1
OUT 1
Source 1
OUT 1
R3
D
R4
35 dB
R3
R4
35 dB
Test port 3
Test port 4
B
Test port 4
Test port 2
(N524xAS Option H85/485)
With extended power range and bias-tees (Option 419), the internal bias-tees limit the maximum test port input power to +30 dBm. The N524xAS Option H85/485 removes the bias-
tees between the source attenuators and the test port couplers. This extends the maximum port power that the analyzer can safely handle to +43 dBm. Selecting Option H85/485 adds internal attenuators and cables. The N524xAS Option H85/485 and Option 419 can not be ordered together. Option H85/485 is not available for the N5247A. When ordering, select N524xAS then add items N524xAS-H85, N524xAS-485 and N524xA-400.
J10
J9
J8
J7
R
Source 1
OUT 1
A
B
C
Source 1
OUT 1
Test port 1
D
Pulse generators
OUT 2
Pulse
modulator
R4
Test port 1
R2
C
D
35 dB
65 dB
Test port 3
B
35 dB
65 dB
Test port 4
65 dB
J3
J2
R
A
B
C
J1
D
LO
OUT 2
Pulse generators
Pulse
modulator
1
To receivers
2
3
35 dB
Test port 2
8
R3
A
65 dB
Source 2
R3
J4
4
R1
Pulse
modulator
OUT 1
J5
LO
OUT
OUT 1
OUT 2
Pulse
modulator
OUT 2
LO
J6
RF
OUT
Source 2
(standard)
IF inputs
rear panel
35 dB
Test port 2
IF inputs
J11
□ High-power configurable and extended power range
65 dB
35 dB
analyzer (Option 423)
Available with 4-port model only, this option adds a combiner and mechanical switches. The mechanical switches provide increased flexibility by having rear panel access (front panel access for the N5247A Source 1 and 2 Out 1) to signal paths for advanced appli-
cations. Requires Options 400, 419 and 080.
rear panel
A
65 dB
65 dB
□ Add an internal combiner and mechanical switches to 4-port D
Test port 3
R1
B
35 dB
65 dB
Test port 1
R2
C
To receivers
D
OUT 2
A
R2
C
65 dB
Pulse
modulator
Test port 1
OUT 2
Pulse
modulator
A
Source 2
R1
Pulse generators
To receivers
Pulse generators
To receivers
D
Source 2
Pulse
modulator
OUT 1
C
Pulse
modulator
OUT 2
LO
A B
OUT 2
LO
R1
A B C
R
OUT 1
IF inputs
rear panel
IF inputs
rear panel
35 dB
R4
C
65 dB
Test port 3
35 dB
R2
D
65 dB
Test port 4
35 dB
B
65 dB
Test port 2
35 dB
PNA Series test set and power configuration options
□ 2-ports, single source, with extended power range (Option 217)
The PNA is an integrated vector network analyzer featuring a
built-in S-parameter test set, one or two synthesized sources
used for device stimulus, a solid-state drive, USB interfaces, and
a 10.4” LCD touch screen display. The N5221A and the N5222A
have 50 ohm, ruggedized 3.5 mm (m) test ports. The N5224A and
the N5225A have 50 ohm, ruggedized 2.4 mm (m) test ports.
The N5227A has a 50 ohm, ruggedized 1.85 mm (m) test ports.
Included with each instrument is a mouse, keyboard (U.S. style),
a 3-year return-to-Agilent service warranty, and one day of onsite productivity assistance (PS-S20-PNA).
The 2-port test set with extended power range comes with a configurable test set, source and receiver attenuators at each port. For N5221/22A, the source attenuators are 65 dB in 5 dB steps and the receiver attenuators are 35 dB in 5 dB steps. For N5224/25A, the source attenuators are 60 dB in 10 dB steps and the receiver attenuators are 35 dB in 5 dB steps. Also included is a solid-state internal RF transfer switch in the R1 reference-receiver path. This configuration is not available on N5227A.
A test set and power configuration option is mandatory, choose
one of the following:
IF inputs
rear panel
Source
OUT 1
□ 2-ports, single source, base configuration (Option 200/210)
Source
OUT 1
A
B
C
35 dB
65 dB
Pulse generators
R2
LO
To receivers
Test port 2
□ 2-ports, single source, with configurable test set (Option 201)
The 2-port configurable test set comes with six front-panel access loops. The loops provide access to the signal path between (a) the source output and the reference receiver, (b) the source output and directional coupler thru arm and (c) the coupled arm of the directional coupler and the port receiver at all ports. Also included is a solid-state internal RF transfer switch in the R1 reference-receiver path.
Source
OUT 1
R
A
B
C
To receivers
35 dB
65 dB
IF inputs
Source
OUT 1
R
A
B
C
D
OUT 2
Pulse
modulator
D
OUT 2
Pulse generators
R1
Pulse generators
R1
35 dB
B
65 dB
Test port 1
Test port 2
9
R2
LO
A
R2
LO
To receivers
Test port 1
B
rear panel
Pulse
modulator
A
R2
(Option 219)
The 2-port test set with extended power range and bias-tee comes with a configurable test set, source and receiver attenuators, and bias-tee at each port. For N5221/22A, the source attenuators are 65 dB in 5 dB steps and the receiver attenuators are 35 dB in 5 dB steps. For N5224/25A, the source attenuators are 60 dB in 10 dB steps and the receiver attenuators are 35 dB in 5 dB steps. For N5227A, both source and receiver attenuators are 50 dB in 10 dB steps. Also included is a solid-state internal RF transfer switch in the R1 reference-receiver path.
IF inputs
rear panel
D
□ 2-ports, single source, with extended power range and bias-tee B
Test port 1
C
LO
A
D
Pulse
modulator
A
Pulse generators
OUT 2
R1
B
OUT 2
R1
IF inputs
R
A
Pulse
modulator
The 2-port with base configuration has no front-panel access loops.
rear panel
R
To receivers
B
35 dB
65 dB
Test port 2
PNA Series test set and power configuration options (continued)
□ 4-ports, dual source, base configuration (Option 400/410)
□ 4-ports, dual source, with extended power range (Option 417)
The 4-port with base configuration has no front-panel access loops.
IF inputs
rear panel
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
OUT 2
Pulse
modulator
To receivers
R3
R1
R4
A
R2
C
The 4-port test set with extended power range comes with two internal sources, configurable test set, source and receiver attenuators at each port. For N5221/22A, the source attenua-
tors are 65 dB in 5 dB steps and the receiver attenuators are
35 dB in 5 dB steps. For N5224/25A, the source attenuators are 60 dB in 10 dB steps and the receiver attenuators are 35 dB in
5 dB steps. Also included is a solid-state internal RF transfer switch in the R1 reference-receiver path. This configuration is not available on N5227A.
IF inputs
rear panel
D
R
Source 1
B
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Test port 1
Test port 3
Test port 4
Pulse generators
Source 2
Test port 2
OUT 1
□ 4-ports, dual source, with configurable test set (Option 401)
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
R3
R4
A
R2
C
D
65 dB
65 dB
Test port 3
Test port 4
35
dB
Test port 2
□ 4-ports dual source, with extended power range and bias-tee Pulse generators
R1
B
35 dB
65 dB
Test port 1
Source 2
OUT 1
D
35 dB
65 dB
Pulse
modulator
To receivers
R2
C
35 dB
OUT 2
LO
R4
A
IF inputs
rear panel
R3
R1
The 4-port configurable test set comes with two internal sources, twelve front-panel access loops. The loops provide access to the signal path between (a) the source output and the reference receiver, (b) the source output and directional coupler thru arm and (c) the coupled arm of the directional coupler and the port receiver at all ports. Also included is a solid-state internal RF transfer switch in the R1 reference-
receiver path.
OUT 2
Pulse
modulator
To receivers
B
(Option 419)
The 4-port test set with extended power range and bias-tee comes with two internal sources, configurable test set, source and receiver attenuators, and bias-tee at each port. For
N5221/22A, the source attenuators are 65 dB in 5 dB steps and the receiver attenuators are 35 dB in 5 dB steps. For N5224/25A, the source attenuators are 60 dB in 10 dB steps and the receiver attenuators are 35 dB in 5 dB steps. For N5227A, both source and receiver attenuators are 50 dB in
10 dB steps. Also included is a solid-state internal RF transfer switch in the R1 reference-receiver path.
IF inputs
rear panel
Test port 1
Test port 3
Test port 4
Test port 2
R
Source 1
OUT 1
A
B
C
D
OUT 2
Pulse
modulator
LO
Pulse generators
Source 2
OUT 1
R3
R1
R4
A
65 dB
Test port 1
R2
C
35 dB
10
OUT 2
Pulse
modulator
To receivers
D
35 dB
65 dB
Test port 3
B
35 dB
65 dB
Test port 4
65 dB
Test port 2
35
dB
PNA-L Series test set and power configuration options
□ 4 ports, single source, base configuration (Option 400)
The PNA-L is an integrated vector network analyzer featuring a
built-in S-parameter test set, one synthesized source used for
device stimulus, a solid state drive, USB interfaces, and a 10.4”
LCD touch screen display. The N5239A, N5231A and the
N5232A have 50 ohm, ruggedized 3.5 mm (m) test ports. The
N5234A and N5235A have 50 ohm, ruggedized 2.4 mm (m) test
ports. Included with each instrument is a mouse, keyboard
(U.S. style), and a 3-year return-to-Agilent service warranty.
For one day of on-site productivity assistance (not included with
instrument purchase), request quantity 1 each PS-S20-PNA.
The 4-port base configuration has no front-panel loops, and is available only on the N5231A and N5232A.
Source
To receivers
A test set and power configuration option is mandatory, choose
one of the following:
R
A
□ 2 ports, single source, base configuration (Option 200)
The 2-port with base configuration has no front-panel access loops.
Test port 1
LO
Source
R2
A
B
Test port 1
B
Test port 2
Test port 2
Source
attenuators (Option 216)
The 2-port test set comes with a configurable test set and source attenuator at each port. The configurable test set adds six front-panel access loops. The loops provide access to the signal path between (a) the source output and the reference receiver, (b) the source output and directional coupler thru arm, and (c) the coupled arm of the directional coupler and the port receiver at all ports. The source attenuators are 60 dB in 10 dB steps.
LO
60 dB
To receivers
R
A
Test port 1
To receivers
60 dB
R2
A
Test port 1
Test port 4
B
C
D
LO
Source
R1
Test port 3
D
attenuator (Option 416)
The 4-port test set comes with a configurable test set and one source attenuator to be shared with all ports. The config-
urable test set adds nine front-panel access loops. The loops provide access to the signal path between (a) the source out
put and the reference receiver, (b) the source output and directional coupler thru arm at all ports, and (c) the coupled arm of the directional coupler and the port receiver at all ports. The source attenuator is 60 dB in 10 dB steps. This configuration is available on only N5231A and N5232A.
□ 2 ports, single source, with configurable test set and source 60 dB
C
□ 4 ports, single source, with configurable test set and source To receivers
R1
LO
B
Test port 2
11
Test port 2
Test port 3
Test port 4
PNA Family Application Options
Measurement applications
□Vector- and scalar-calibrated converter measurements (Option 083)
Solid black series name indicates the feature is available on
that series, while gray series name with strikethrough indicates the feature is not available on that series. For example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
□Automatic fixture removal (Option 007)
PNA-X PNA PNA-L
Many devices do not have coaxial connectors and are put in fixtures in order to measure them in a coaxial environment. Accurately removing the effects of the fixture is required to get a good mea-
surement of the device under test (DUT). This option adds a power-
ful application wizard to guide you through characterizing a fixture and removing it from the measurement. Devices can be single end-
ed or differential. Files can be saved in a variety of formats for later use in PNA, ADS, and PLTS. Available as PNA-X, PNA, and PNA-L Option 007 upgrade kit. Windows 7 operating system and firmware A.10.20 or higher is required.
□Time domain (Option 010)
PNA-X PNA PNA-L
This option enables the analyzer to view reflection and trans-
mission responses in time or distance. Use time domain to tune
filters, gate out the response of fixtures and cables, characterize the impedance of transmission lines and more. If eye-diagram anal-
ysis, W-element modeling or high-speed interconnect testing is required, PLTS N1930B software must be used.
□Frequency offset (Option 080)
PNA-X PNA PNA-L
This option enables the analyzer to set the source frequency independently from where the receivers are tuned, and is required to configure an external source using External Device Configuration. This ability is important for measuring amplifiers, mixers, and frequency converters.
□Scalar-calibrated converter measurements (Option 082)
PNA-X PNA PNA-L
With a simple setup and calibration, this application delivers the highest accuracy for scalar conversion-loss/gain measurements by combining one-port and power-meter calibrations to remove mismatch errors. Option 082 provides an intuitive and easy-to-use user interface for setting up mixer and converter measurements, with single or dual conversion stages. It can control the analyz-
er’s built-in source(s) as well as external signal generators for use as LO signals. Supported external sources include the Agilent ESG, PSG, and MXG Series, as well as other SCPI-controlled
signal generators. Option 082 requires Option 080, and cannot be ordered with Option 083. It is compatible with Option 084, which enables measurements of converters with internal LOs.
PNA-X PNA PNA-L
This application includes the scalar mixer/converter plus phase (SMC+Phase) measurement class that provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C/F/G comb generator and an external DC power supply capable of sourcing +15 V to 300 mA for U9391C/F or 800 mA for U9391G1. A vector mixer/converter measurement (VMC) class is also included for measuring the phase difference between multi-
ple paths or devices, or for measuring phase shifts within a device. Using VMC or the comb-generator-based calibration for SMC+Phase requires an instrument with a configurable test set (i.e., has front-panel RF loops). For units without front-panel loops, SMC+Phase can be used with a calibration mixer supplied by the user. Option 083 provides an intuitive and easy-to-use user inter-
face for setting up mixer and converter measurements, with single or dual conversion stages. It can control the analyzer’s built-in source(s) as well as external signal generators for use as LO sig-
nals. Supported external sources include the Agilent ESG, PSG, and MXG Series, as well as other SCPI-controlled signal generators. Option 083 requires Option 080, and cannot be ordered with
Option 082. It is compatible with Option 084, which enables mea-
surements of converters with internal LOs.
□Embedded LO measurements (Option 084)
PNA-X PNA PNA-L
This option tunes the analyzer’s receivers to the output frequency of the converter under test without the need for access to internal LOs or a common reference signal. For converters with embedded LOs, this option requires Option 082 (enables match-corrected conversion loss/gain measurements) or Option 083 (enable abso-
lute group delay measurements). This option also works with Option 086 gain compression application, Option 087 intermodula-
tion distortion application, and Option 028/029/H29 noise figure applications.
□Gain compression application (Option 086)
PNA-X PNA PNA-L
The gain compression application (GCA) provides input power,
output power, gain, and phase at the compression point of an amplifier or frequency converter, over a specified frequency range. GCA's SMART Sweep is very fast and easy-to-use. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
1. When a comb generator is used as a phase reference for calibration and the start frequency of the measurement is less than 55 MHz, a user-supplied calibration mixer
is required. For measurements between 50 GHz and 67 GHz, an additional high-pass filter is required (two back-to-back Agilent V281A waveguide-to-coax adapters
recommended; must be ordered separately).
12
PNA Family Application Options (continued)
Measurement applications (continued) □Integrated true-mode stimulus application (Option 460)
Solid black series name indicates the feature is available
on that series, while gray series name with strikethrough indicates the feature is not available on that series. For example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
□Intermodulation distortion application (Option 087)
PNA-X PNA PNA-L
The intermodulation distortion (IMD) application makes it very easy to set up and calibrate swept-IMD measurements of both amplifiers and frequency converters. It controls the frequency and power of internal and external sources and tunes the receivers to the main tones as well as the IMD products in a single measurement channel. The user can sweep either the center frequency of the two stimulus signals, the frequency spacing of the two stimulus signals about a fixed center fre-
quency, or the power of one or both stimulus signals or the power of the LO signal. The analyzer can measure intermodula-
tion distortion products of order 2, 3, 5, 7, or 9, and can display the associated intercept points. In addition, an IM Spectrum mode gives a spectrum-analyzer-like display for confirming or trouble-shooting measurements. Requires Option 080. Not avail-
able with PNA Options 200, 210, 400 and 410. When configured with a 2-port PNA or 2-port PNA-X with either Option 200 or 219, an external signal generator and a combiner are required. When configured with a 4-port PNA or 4-port PNA-X with
Option 400 or 419, the two internal sources and an unused
test port coupler configured as a combiner can be used for
two-tone IMD measurements. When configured with PNA-X
Option 224 or 423, the two internal sources and internal combin-
er can be used for two-tone IMD measurements.
□Source phase control (Option 088)
PNA-X PNA PNA-L
This option allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. Option 088 also controls the relative power level between the sources using the receiver-leveling feature. Option 088 is useful for two applications. The first is for active-load control, where the analyzer provides a precise, electroni-
cally settable impedance to the output port of a device, while gain and output power are measured. This capability can be combined with external load-pull software to create traditional load-pull power contours. The second application is to provide a pair of phasecontrolled sources for differential, quadrature, or arbitrary phase-off
set signals at a fixed or swept frequency. Typically in this case, another instrument, receiver, or detector would be used to measure the response of the DUT. Not available with PNA Options 200 and 210.
□N-port capabilities (Option 551)1
13
PNA-X PNA PNA-L
Adds a multiport analyzer mode, which enables full N-port error correction and measurement capabilities using an external test set. Only standard measurement class is available in the multi-
port analyzer mode. Not available with PNA Options 200, 210, 400 and 410. For multiport analysis greater than 8 ports, it is highly recommended to use PLTS software N1930B to manage the large data format files that easily grow exponentially (12 port S-parameter files have 144 S-parameter elements).
□PNA Firmware for ambient temperature CalPod operation (Option 301)
PNA-X PNA PNA-L
Firmware that enables ambient temperature CalPods (85530B, 85540A), and no more than four CalPods to operate with a PNA family network analyzer.
□PNA Firmware for temperature characterized CalPod operation
(Option 302)
PNA-X PNA PNA-L
Firmware that enables temperature characterized CalPods (85531/
32B or 85541/42A) to be used with a PNA family network analyzer. Enables operation with more than four CalPods, but only controls four at a time.
Noise figure options
□Noise figure measurements using standard receivers
1. When configuring N524xA as a multiport analyzer using Option 551 and a multiport test set, the combiner feature of Option 224 or 423 is temporarily
disabled. When configured as a standalone analyzer, the combiner feature is enabled. When ordering a test set, select an appropriate interface kit.
Refer to page 22 Multiport Measurements section for more details.
2. Only N4690 Series ECal modules are supported for use as an impedance tuner.
PNA-X PNA PNA-L
Integrated true-mode stimulus application (iTMSA) provides mis-
match-corrected true-mode (true differential mode and true com-
mon mode) stimulus and enables accurate balanced measurements under real operating conditions. iTMSA also provides balanced measurements with forward-only sweep, reverse-only sweep, and frequency or power sweep with arbitrary phase and amplitude off-
sets. Requires one of Options 400, 401, 410, 417, 419 and 423.
(Option 028)
PNA-X PNA PNA-L
This option adds firmware for high-accuracy noise figure measurements of amplifiers, frequency converters, and mixers using the analyzer's standard receivers, and utilizing Agilent's unique source-correction technique. Using an Agilent ECal module
configured as an impedance tuner (N4691B/93A/94A-M0F rec-
ommended; must be ordered or supplied separately2), the effects of imperfect system-source match are removed, greatly improving the accuracy of the cold-source technique. This approach sur-
passes the accuracy provided by the Y-factor method and other cold-source implementations. A scalar calibration choice is also available that offers less accuracy but is faster and does not require the external ECal module used as an impedance tuner. For calibration, a power meter and separate ECal module or mechani-
cal calibration kit is required (must be ordered or supplied sepa-
rately). An external preamplifier and filter(s) is required for devices with < 30 dB of excess noise (gain plus noise figure in dB) up to 20 GHz, < 40 dB up to 50 GHz, or < 45 dB up to 67 GHz. Front panel jumpers provide a convenient spot for adding a preamplifier and filter for low gain, low noise figure devices. Not available with N522xA-200 and -400.
PNA Family Application Options (continued)
Noise figure options (continued)
Solid black series name indicates the feature is available on
that series, while gray series name with strikethrough indicates the feature is not available on that series. For example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
□Fully-corrected noise figure measurements (Option 029)
PNA-X PNA PNA-L
This option adds a low-noise receiver and firmware to the PNA-X1 for high-accuracy noise figure measurements of amplifiers, fre-
quency converters, and mixers, utilizing Agilent's unique source-
correction technique. Using an Agilent ECal module configured as an impedance tuner for N5241/42/49A (3.5 mm N4691B-M0F
recommended; must be ordered or supplied separately2), or a built-in tuner for N5244/45/47A, the effects of imperfect system-
rear panel
source match are removed, greatly improving the accuracy of the cold-source technique. This approach surpasses the accuracy
provided by the Y-factor method and other cold-source implemen-
tations. A scalar calibration choice is also available that offers less accuracy but is faster, and for N5241/42/49A, does not require the external ECal module used as an impedance tuner. For calibration of the noise receiver, Option 029 requires a power meter or a 346 series noise source (346C or 346C-K01 recom-
mended). For measurements of mixers and converters, a power meter is always required. The noise source and power meters are only used during calibration of the analyzer, and must be ordered or supplied separately. During the S-parameter portion of the noise calibration, a separate ECal module or mechanical calibra-
tion kit is required (also must be ordered or supplied separately). Option 029 also allows noise figure measurements using the stan-
dard receivers for high-gain (> 60 dB), narrowband devices that might otherwise overload the low-noise receiver, or for noise fig-
ure measurements up to 67 GHz on the N5247A1.
IF inputs
+28V
J11
J10
J9
J8
J7
J4
J6
J5
RF
OUT
LO
OUT
J3
Source 1
R1
J1
D
3
R3
35 dB
R4
35 dB
65 dB
Test port 3
rear panel
Impedance tuner for noise
figure measurements
R2
D
35 dB
65 dB
B
65 dB
35 dB
Test port 4
N5241/42/49A 4-port block diagram
with noise figure option
Test port 2
IF inputs
+28V
J11
J10
J9
J8
J7
J6
J5
RF
OUT
LO
OUT
J4
J3
R1
C
J1
D
2
3
OUT 1
R3
Noise receivers
10 MHz - 6 - 50
GHz
6 GHz
4
LO
OUT 2
Pulse
modulator
Pulse
modulator
A
B
1
OUT 2
60 dB
A
Pulse generators
Source 2
Source 1
OUT 1
J2
R
Signal
combiner
+
-
N5244/45A 4-port block diagram
with noise figure option
3–8.5/
13.5/
26.5 GHz
10 MHz 3 GHz
To receivers
C
Test port 1
Noise receivers
4
LO
OUT 2
Pulse
modulator
Pulse
modulator
A
C
2
OUT 1
OUT 2
65 dB
B
1
Source 2
OUT 1
A
Pulse generators
Signal
combiner
+
-
J2
R
To receivers
R4
C
R2
D
B
Tuner
35 dB
35 dB
60 dB
Test port 1
35 dB
60 dB
Test port 3
60 dB
35 dB
Test port 4
Test port 2
IF inputs
rear panel
J7
Source 1
J12
J6
J5
RF2
OUT
RF1
OUT
LO
OUT
J4
J2
R
A
B
C
J1
D
Pulse generators
OUT 2
OUT 1
J3
Pulse
modulator
1
Source 2
(standard)
2
3
OUT 1
Pulse
modulator
Signal
combiner
4
LO
OUT 2
To receivers
Noise receivers
10 MHz - 6 - 50
GHz
6 GHz
Tuner
R1
N5247A 4-port block diagram
with noise figure option
A
R3
C
R4
D
R2
B
50
dB
50 dB
50 dB
Test port 1
Test port 3
1. For N5247A, the low-noise receiver works up to 50 GHz only
2. Only N4690 Series ECal modules are supported for use as an impedance tuner.
14
50 dB
50 dB
Test port 4
50 dB
50 dB
Test port 2
50 dB
Noise figure options summary
Overview
Option 028
Option 029
Description
Noise figure application using standard receivers
only, for all PNA / PNA-X models.
Noise figure application using standard or low-noise
receivers, for all PNA-X models.
Required options
080, and 082 or 083 for measuring frequency converters.
Not available with N522xA-200 and -400.
For N5241/42/49A, 080 and either 219, 224, 419, 423, or
H85. For N5244/45/47A, 080 and either 224 or 423.
For measuring frequency converters, requires Option 082
or 083.
Includes low-noise receivers
No
Yes1
Includes filters for LO-harmonic
rejection
No
Yes1
Includes source tuner bypass switch
No
Yes
Use standard receivers for noise
figure measurements2
Yes
Yes
Vector noise calibration available
using ECal as tuner
Yes
Yes
Vector noise calibration using built-in tuner
No
Yes, for N5244/45/47A
Recommended ECal for vector
noise calibration3
3.5 mm N4691B-M0F (N5221/22/41/42/49A)
2.4 mm N4693A-M0F (N5224/25/44/45A)
1.85 mm N4694A-M0F (N5227/47A)
3.5 mm N4691B-M0F (N5241/42/49A)
Built-in for N5244/45/47A
Included tuner accessories for m-f ECal
3.5 mm N5242-20137 cable, 85052-60013 m-f adapter
(N5221/22/41/42/49A)
2.4 mm N5245-20140 cable, 85056-60007 m-f adapter
(N5224/25/44/45A)
1.85 mm N5247-20142 cable, 85058-60115 m-f
adapter (N5227/47A)
3.5 mm N5242-20137 cable, 85052-60013 m-f adapter
(N5241/42/49A)
N/A for N5244/45/47A, due to built-in tuner
Recommended adapter for f-f ECal tuner
(N4691B/93A/94A-00F)
3.5 mm 85052-60014 m-m adapter (N5221/22/41/42/49A)
2.4 mm 85056-60005 m-m adapter (N5224/25/44/45A)
1.85 mm 85058-60113 m-m adapter (N5227/47A)
3.5 mm 85052-60014 m-m adapter (N5241/42/49A)
N/A for N5244/45/47A, due to built-in tuner
Scalar noise calibration available
Yes
Yes
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Max frequency, using low-noise
receivers (GHz)
N/A
8.5/13.5/26.5/43.5/50
Max frequency, using standard
receivers (GHz)2
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Calibration accessories for low-noise
receivers
N/A
Cal kit or ECal, 346C or 346C-K01 noise source or power
meter
Calibration accessories for standard
receivers
Cal kit or ECal, power meter
Cal kit or ECal, power meter
Max input frequency (GHz)
8.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Max output frequency, using low-noise
receivers (GHz)
N/A
8.5/13.5/26.5/43.5/50/67
Max output frequency, using standard
receivers (GHz)2
18.5/13.5/26.5/43.5/50/67
8.5/13.5/26.5/43.5/50/67
Calibration accessories for low-noise
receivers
N/A
Cal kit or ECal, power meter, 346C or 346C-K01 noise
source (optional)
Calibration accessories for standard
receivers
Cal kit or ECal, power meter
Cal kit or ECal, power meter
S-parameter, conversion gain/loss
measurements
Max freq (GHz)
NF measurements, amplifiers
NF measurements, converters
1. For N5247A, the low-noise receiver works up to 50 GHz only.
2. External preamplifier and filter(s) required if DUT excess noise (gain plus noise figure) is < 30 dB up to 20 GHz, < 40 dB up to 50 GHz, or < 45 dB up to 67 GHz.
3. Only N4690 Series ECal modules are supported for use as an impedance tuner.
15
PNA Family Application Options (continued)
Pulse, antenna, mm-wave
□Add four internal pulse generators (Option 025)
Solid black series name indicates the feature is available
on that series, while gray series name with strikethrough
indicates the feature is not available on that series. For
example;
PNA: Available on PNA Series
PNA: Not available on PNA Series
□Pulsed-RF measurements (Option 008)
8
PNA-X PNA PNA-L
This option adds narrowband pulse detection mode and extends the pulsed-RF measurement capability to narrower pulse widths below the limit for the standard wideband detection mode. The PNA-X and PNA are complete pulsed-RF solutions with built in pulse generators and modulators, so external test sets and pulse generators are not required. With narrowband detection mode, Option 008 sets the coefficient of the analyzer’s digital-IF filters to null out unwanted spectral components, enables the internal receiver IF gates, controls internal pulse generators (Option 025), internal pulse modulators (Option 021 and/or 022), and external pulse modulators, and performs optimization for measurement sensitivity. Option 008 also includes conventional pulsed-RF mea-
surement software (Option H08). Option 025 is required. Option 021 is recommended for forward-only pulsed-RF measurements. Option 021 and 022 are recommended for bi-directional pulsed-RF measurements. The N1966A pulse I/O adapter is recommended if using external pulse generators and/or external pulse modulators
6
14
5
13
4
12
3
11
2
10
1
9
Pulse I/O D-sub connector (DB-15 female)
□Fast CW Sweep (Option 118)
PNA-X PNA PNA-L
This option uses FIFO (first-in first-out) to allow external point-
trigger acquisition of 400,000 data points per second on five measurement receivers. When enabled, there is no display update, no background computation, or other interference from the vector network analyzer application. All the data gathered is placed into a 500 million points FIFO buffer. While the data is going into FIFO it can be read from the FIFO buffer.
Nonlinear vector network analysis
Please refer to 5989-8575EN Nonlinear Vector Network
Analyzer brochure for more information.
PNA-X PNA PNA-L
This option enables external IF inputs on the rear panel of the analyzer for applications such as antenna and millimeter-wave test.
□Add pulse modulator to internal first source (Option 021)
PNA-X PNA PNA-L
This option enables the internal pulse modulator on Source1 Out1. Control of the modulator can also be done via pin 8 of the Pulse I/O D-sub connector on the rear panel of the analyzer using an external pulse generator, or by using one of the inter-
nal pulse generators (Option 025). The N1966A pulse I/O adapter is recommended if using an external pulse generator.
□Add pulse modulator to internal second source (Option 022)
7
15
□Add IF inputs for antenna and millimeter-wave (Option 020)
PNA-X PNA PNA-L
This option enables four internal pulse generators. These pulse generators can be used to control the internal pulse modulators and internal receiver IF gates, and are also available on pins 10 through 13 of the Pulse I/O D-sub connector on the rear panel of the analyzer to control external modulators and/or gates. The N1966A pulse I/O adapter is recommended if using external pulse modulators.
PNA-X PNA PNA-L
This option enables the internal pulse modulator on Source2 Out1. Control of the modulator can also be done via pin 8 of the Pulse I/O D-sub connector on the rear panel of the analyzer using an external pulse generator, or by using one of the inter-
nal pulse generators (Option 025). The N1966A pulse I/O adapter is recommended if using an external pulse generator. Option 224 or 400 is required for PNA-X, and one of Option 400, 401, 417, or 419 is required for PNA.
16
PNA Family Application Options (continued)
Accessories
□Comb Generators
Solid black series name indicates the feature is available
on that series, while gray series name with strikethrough
indicates the feature is not available on that series. For
example;
U9391C 10 MHz to 26.5 GHz
U9391F 10 MHz to 50 GHz
U9391G 10 MHz to 67 GHz
PNA: Available on PNA Series
PNA: Not available on PNA Series
□Rack mount kit without handles (Option 1CM)
PNA-X PNA PNA-L
Adds a rack mount (ICM042A) and rail kit (E3663AC) for use without handles.
□Rack mount kit with handles (Option 1CP)
PNA-X PNA PNA-L
Adds handles (5063-9230), a rack mount (5063-9237) and rail kit (E3663AC) for use with handles.
PNA-X PNA PNA-L
The U9391C/F/G provides precision phase calibration, traceable to the National Institute of Standards and Technology (NIST) standard. It is used for nonlinear measurements with the PNA-X nonlinear vector network analyzer (NVNA). NVNA requires two comb generators, one is connected during measurements and another is used only during calibration. A comb generator is also used to characterize the VNA receivers for delay measurements of frequency converters using PNA-X or PNA with Option 083.
□Pulse I/O adapter (N1966A)
Comb generator enables vector-corrected
measurements at fundamental and
harmonic frequencies
PNA-X PNA PNA-L
An adapter for connecting between the Pulse I/O connector on the rear panel of the analyzer and the coaxial inputs and outputs of external pulse generators and external pulse modu-
lators. Coaxial connectors are SMB-male. The PULSE IN
connectors are for controlling the analyzer’s internal IF gates, which are enabled with Option 008 and used with narrowband detection. The PULSE OUT connectors are from the four internal pulse generators, which are enabled with Option 025. The PULSE SYNC IN connector is used to synchronize the internal pulse generators with an external timing pulse. The RF PULSE MOD IN connector controls the internal pulse modulator(s) which are enabled with Options 021 and 022.
□N1930B Physical Layer Test System Software (PLTS) version 2013
PNA-X PNA PNA-L
The Physical Layer Test System (PLTS) version 2013 software is a powerful signal integrity tool for today's high-speed digital designers. The PLTS software platform has become an industry standard for calibration, measurement and analysis of linear passive interconnects such as cables, connectors, backplanes and printed circuit boards. Utilizing either a Vector Network Analyzer (VNA) or Time Domain Reflectometer (TDR), fast and accurate measurements can be obtained without in-depth knowledge of microwave measurement techniques.
□CalPod calibration refresh modules (Options 301, 302)
Pulse I/O adapter (N1966A) simplifies connections
PNA-X PNA PNA-L
This firmware option enables the PNA-X, PNA, and PNA-L to operate with CalPod calibration refresh modules. CalPods allow in-situ calibration refreshes to be performed at the push of a button without removing the DUT or connecting calibration standards. This option requires the use of appropriate CalPod module hardware. CalPods are useful in any measurement
situation where it is desirable to have assurance that a valid calibration is present before recording measurement data. Some of the measurement applications where CalPods have proven useful are as follows:
•
•
•
•
•
•
•
•
17
Thermal-vacuum testing
Temperature chamber testing
Measurement of low-loss devices
Applications that require frequent re-calibrations
Applications that have complex and lengthy calibrations,
such as multi-port measurements
Measurement of cables installed in aircraft
Removing switch matrix repeatability errors
Removing switch and connector repeatability errors in
complex ATE test systems
PNA Family Network Analyzer Upgrade Kits
Frequency, test ports, test set and power configurations
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Description
Required Option
For PNA-X
Series
For PNA
Series
For PNA-L
Series
User
Installable
Frequency upgrade1
Extend analyzer's frequency range to 13.5 GHz
N5239A or N5249A
N5249AU-913
n/a
N5239AU-613
No
Extend analyzer's frequency range to 20 GHz
N5239A or N5231A
n/a
n/a
N5239AU/31AU-620
No
Extend analyzer's frequency range to 26.5 GHz
N5241A, N5249A, or
N5221A
N5241AU-960/
49AU-960
N5221AU-626
n/a
No
Extend analyzer's frequency range to 50 GHz
N5244A, N5224A or
N5234A
N5244AU-990
N5224AU-650
N5234AU-650
No
Expand 2-ports, single source without
configurable test set to 4-ports
N522xA-200
n/a
N522xAU-600
n/a
No
Expand 2-ports, single source with
configurable test set to 4-ports
N524xA-200 or
N522xA-201
N524xAU-940
N522xAU-601
n/a
No
Expand 2-ports, single source with
configurable test set and extended power
range to 4-ports
N522xA-217
n/a
N522xAU-617
n/a
No
Expand 2-ports, single source with
configurable test set, extended power range
and bias-tees to 4-ports
N524xA-219 or
N522xA-219
N524xAU-942
N522xAU-619
n/a
No
Expand 2-ports, internal second source with
configurable test set, extended power range,
bias-tees, combiner and mechanical switches
to 4-ports
N524xA-224
N524xAU-944
n/a
n/a
No
Add configurable test set, 2-ports
Add configurable test set and source
attenuators, 2-ports
N522xA-200
n/a
N522xAU-201
n/a
No
N523xA-200
n/a
n/a
N523xAU-216
No
Add extended power range, 2-ports2
N522xA-201
n/a
N522xAU-217
n/a
No
Add bias-tees, 2-ports2
N522xA-217
n/a
N522xAU-219
n/a
No
Add extended power range and bias-tees,
2-ports
N524xA-200 or
N5227A-201
N524xAU-921
N5227AU-217/219
n/a
No
Add internal 2nd source, combiner and
mechanical switches, 2-ports
N524xA-219 or
N522xA-219
N524xAU-922
n/a
n/a
No
Add high power configurable, 2-ports
N524xA-219 or 224
N524xAU-H85
n/a
n/a
No
Add configurable test set, 4-ports
N522xA-400
n/a
N522xAU-401
n/a
No
Add configurable test set and source
attenuators, 4-ports
N523xA-400
n/a
n/a
N523xAU-416
No
Add extended power range, 4-ports2
N522xA-401
n/a
N522xAU-417
n/a
No
Add bias-tees, 4-ports2
N522xA-417
n/a
N522xAU-419
n/a
No
Add extended power range and bias-tees,
4-ports
N524xA-400 or
N5227A-401
N524xAU-926
N5227AU-417/419
n/a
No
Add internal 2nd source, combiner and
mechanical switches, 4-ports
N524xA-419 or
N522xA-419
N524xAU-927
n/a
n/a
No
Add high power configurable, 4-ports
N524xA-419 or 423
N524xAU-H85
n/a
n/a
No
Test ports
Test set and power configuration
1. Frequency upgrade options from 8.5/13.5/20/26.5 GHz to 43.5/50 GHz and 43.5/50 GHz to 67 GHz are not available. Trade-in is recommended.
2. Not available on N5227A.
18
PNA Family Network Analyzer Upgrade Kits (continued)
Application options
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Description
For PNA-X
Series
Required Option
For PNA
Series
For PNA-L
Series
User
Installable
N524xAU-007
N522xAU-007
N523xAU-007
Yes
N524xAU-010
N522xAU-010
N523xAU-010
Yes
N524xAU-028
N524xAU-9243
N522xAU-028
n/a
Yes
n/a
n/a
No
N524xAU-9293
n/a
n/a
No
Measurement applications
Automatic fixture removal
Windows 7 OS and firmware A.10.20 or
higher required.7
Time-domain measurements
Noise figure measurements using standard receivers
Option 0801,2
Fully-corrected noise figure measurements
for PNA-X, 2-ports
Option 080 and for N5241/42/49A,
one of Options 219, 224 or H851.
For N5244/45/47A, 080 and 224
Fully-corrected noise figure measurements
for PNA-X, 4-ports
Option 080 and for N5241/42/49A,
one of Options 419, 423 or H851.
For N5244/45/47A, 080 and 423
Frequency offset
N524xAU-080
N522xAU-080
N523xAU-080
Yes
N524xAU-082
N522xAU-082
N523xAU-082
Yes
Vector- and scalar-calibrated converter measurements
Option 080
Option 0808
N524xAU-083
N522xAU-083
n/a
Yes
Embedded LO measurements
Option 082 or 083
N524xAU-084
N522xAU-084
n/a
Yes
Gain compression application
See Footnote 1
N524xAU-086
N522xAU-086
n/a
Yes
Intermodulation distortion application
Option 0801,4
N524xAU-087
N522xAU-087
n/a
Yes
Source phase control
See Footnote 5
N524xAU-088
N522xAU-088
n/a
Yes
Ambient temperature CalPod firmware
N524xAU-301
N522xAU-301
N523xAU-301
Yes
Temperature characterized CalPod firmware
N524xAU-302
N522xAU-302
N523xAU-302
Yes
Scalar-calibrated converter measurements
Integrated true-mode stimulus application
Option 400, 401, 417, 419, or 423
N524xAU-460
N522xAU-460
n/a
Yes
N-port capabilities
See Footnote 6
N524xAU-551
N522xAU-551
N523xAU-551
Yes
Option 0251
N524xAU-008
N522xAU-008
n/a
Yes
N524xAU-020
N522xAU-020
n/a
Yes
N524xAU-021
N522xAU-021
n/a
Yes
N524xAU-022
N522xAU-022
n/a
Yes
Add four internal pulse generators
N524xAU-025
N522xAU-025
n/a
Yes
Fast CW sweep
N524xAU-118
N522xAU-118
n/a
Yes
Pulse, antenna, mm-wave
Pulsed-RF measurements
Add IF inputs
Add pulse modulator to internal 1st source
Add pulse modulator to internal 2nd source
Option 224, 400, 401, 417, 419, or 423
1. For measuring frequency converters, Option 082 or 083 is required.
2. Requires configurable test set for signal conditioning of noise figure measurements using standard receivers. Therefore it is not available with N522xA-200, -210, -400 and -410.
3. Upgrading N5244A units with noise figure hardware requires serial-number prefixes of 5204 or higher, and upgrading N5245A units requires serial-number prefixes of 5205 or higher. For these two models, units with lower serial-number prefixes can be traded in for credit towards a new unit with the noise figure hardware.
4. Two-tone signal must be routed to R1 receiver after an external combiner; therefore it is not available with N522xA-200, -210, -400 and -410.
5. When used with an external signal generator, configurable test set is required to access a receiver. Therefore it is not available with N522xA-200 and -210.
6. To connect a multiport test set, configurable test set is required. Therefore it is not available with N522xA-200, -210, -400, -410, and N523xA-200, and -400.
7. The Windows 7 upgrade kit is model N8983A. This upgrade kit requires an i7 or Celeron CPU. For units with older CPUs, order Option PC6 of the N8983A which also includes a new i7 CPU.
8. A configurable test set is required for VMC measurements (to connect a reference mixer) or for SMC+Phase measurements using the comb-generator-based calibration. When ordered with N522xA-200, -210, -400 and -410, Option 083 adds phase and delay measurements only by using SMC+Phase with a calibration mixer.
19
PNA Family Network Analyzer Upgrade Kits (continued)
Application options
Upgrade kits are available to add options after initial purchase. To upgrade the PNA-X/PNA/PNA-L, order the corresponding
item number. The model and serial numbers of the instrument to be retrofitted are required as part of the order.
Description
For PNA-X
Series
Required Option
For PNA
Series
For PNA-L
Series
User
Installable
Nonlinear network vector analysis
Nonlinear component characterization
Nonlinear X-parameters
Options 419 and 080, or 400, H85
and 080
N524xAU-510
n/a
n/a
Yes
Options 423 and 510
N524xAU-514
n/a
n/a
Yes
Nonlinear pulse envelope domain
Requries Options 021, 025 and
either one of 510 or 514
N524xAU-518
n/a
n/a
Yes
Arbitrary load-impedance X-parameters
Option 514
N524xAU-520
n/a
n/a
Yes
Perpetual license for built-in performance test software for Agilent inclusive calibration
N524xAU-897
N522xAU-897
N523xAU-897
Yes
Perpetual license for built-in performance test
software for standard compliant calibration
N524xAU-898
N522xAU-898
N523xAU-898
Yes
Calibration software
20
PNA Family Network Analyzer Upgrade Kits
Upgrade paths
PNA-X upgrade path
Frequency
2-ports
8.5 GHz
400
921
13.5 GHz
1
924
219/029
N5241AU-960
1
26.5 GHz
940
200
N5249AU-913
4-ports
N5249AU-960
43.5 GHz
922
224/029
926
942
219
922
2
924
9291 419/029
419
1
927
927
944
224
N5244AU-990
9292
423
423/029
H85
50 GHz
High power configurable
67 GHz
Frequency
PNA upgrade path
2-ports
43.5 GHz
13.5 GHz
N5221AU-626
26.5 GHz
200
N5224AU-650
201
201
50 GHz
217
217
67 GHz
219
219
Frequency
8.5 GHz
PNA-L upgrade path
43.5 GHz
N5239AU-613
13.5 GHz
N5234AU-650
50 GHz
600
601
617
619
4-ports
400
401
401
417
417
419
419
2-ports
4-ports
200
400
216
216
416
416
N5231AU-620
20 GHz
N5239AU-620
1. This upgrade path only available on N5241/42/49A.
2. Upgrading N5244A units with noise figure hardware requires serial-number prefixes of 5204 or higher, and upgrading N5245A units requires serial-number
prefixes of 5205 or higher. For these two models, units with lower serial-number prefixes can be traded in for credit towards a new unit with the noise figure hardware.
Applications
Material measurements
Multiport measurements
□85070E High-Temperature Dielectric Probe Kit
The multiport test sets are designed to work with the PNA Family
of network analyzers and provide network analysis with a single
set of connections for devices that have multiple ports. The
test sets are configured in a variety of ways, for extension or
switching, electro-mechanical or solid-state switches, number of
test ports, frequency range, and 2- or 4-ports depending on your
analyzer.
The 85070E enables measurements of the dielectric properties of materials quickly and conveniently. Measurements made with this probe are nondestructive and require no sample preparation. The dielectric probe is well suited for measurements of liquid, semisolid and flat solid materials. Measurement results can be viewed in a variety of formats (ε’r, ε”r, tan δ
or Cole-Cole). The supplied software can be run in the PNA analyzer or on a PC.
Test set types–extension and switching test sets
Switching test sets provide an economical solution for RF applications. This test set is connected to the test ports of the VNA, and
group of test ports share the directional couplers and receivers in
the VNA. An extension test set is connected to the sources and
test receivers through configurable test set of the VNA. It features
a directional coupler for every test port and all switching occurs
behind the directional couplers, which provides the ultimate
in flexibility, stability, and performance for RF and microwave
applications.
□85071E Materials Measurement Software
The 85071E materials measurement software calculates the permittivity and permeability of material samples placed in a coaxial airline or a rectangular waveguide. The measurement technique works well for solid materials that can be machined to fit precisely inside a transmission line. Measurement results can be viewed in a variety of formats (ε’r, εr, µ’r, µ”r, tan δ, or Cole-Cole µ). The software can be run in the PNA analyzer or on a PC.
Switch types – electro-mechanical and solidstate switches
Signal integrity measurements
The electro-mechanical switches have less insertion loss, higher
power handling, and linear responses. Thus it is recommended
for testing active devices, high-power devices, and devices that
require wide dynamic range. However, they have limited switching
life (mostly 5 million cycles) and long setting time. On the other
hand, the solid-state switches have unlimited switching life, very
fast switching speed and excellent repeatability thus they are
often used for high volume passive device tests, and S-parameter
measurements of passive components can be performed.
□N1930B Physical Layer Test System (PLTS) Software
The PLTS software platform has become an industry standard for calibration, measurement and analysis of linear passive interconnects such as cables, connectors, backplanes and printed circuit boards. Utilizing either a vector network analyzer (VNA) or a time domain reflectometer (TDR), fast and accurate mea-
surements can be obtained without in-depth knowledge of microwave measurement techniques. Refer to www.agilent.
com/find/plts or the technical overview, literature number 5989-6841EN for more details.
Test set model number
Multiport test set model numbers represent the test set types,
note the numbering scheme below.
Note that there are some test sets that do not follow this numbering scheme such as U3022AE10, U3025AE06, and U3025AE10, which use
solid-state switches, and U3022AS66, which includes 1x6 switching test set and six calibration distribution ports.
22
Millimeter-wave measurements
Test set options
One of the following test set options must be selected.
□Standard configuration (Option 700)
The standard configuration is the basic test set configuration, which does not include signal conditioning devices such as amplifiers.
□Add amplifiers for improved dynamic range (Option 001)
Option 001 adds an amplifier between each test port coupler and the receiver switch to improved system dynamic range. It is primarily offered for the test set with solid-state switches to compensate for the insertion loss.
□Add amplifiers and bias-tees (Option 002)
Option 002 adds an amplifier between each test port coupler and the receiver switch to improved system dynamic range and bias-tees for all test ports on the test set as well as the ana-
lyzer. It is primarily offered for the test set with solid-state switches to compensate for the insertion loss.
□Single sweep solution to 110 GHz
Interface kits
The interface kit includes a set of semi-rigid RF jumper cables
and two pairs of rear locking feet that connect and lock the analyzer and the test set together. When ordering a multiport test
set, the analyzer that is used with the test set must be specified
to add one of the following interface kits. The availability depends
on the test set model. There are following three interface kit
models based on the jumper connector layouts on the test set.
Therefore, only one interface kit model (“PX”, “PN”, or “PL”) is
available on each test set. Each interface kit model has one digit
suffix indicating the connector type; 1 for 1.85 mm, 2 for 2.4 mm
and 3 for 3.5 mm (or SMA).
□U3021PXx □U3021PNx □Option 261
□Option 262
□Option 263
□Option 430
□Option 242
□Option 442
□Option 245
□Option 445
□Option 247
□Option 447
The 67 GHz PNA and PNA-X network analyzers allow extend-
ing the maximum frequency to 110 GHz with a 1.0 mm coaxial connector, enabling 10 MHz to 110 GHz single sweep mea-
surements using a millimeter-wave controller and frequency extenders with built-in combiner.
The 10 MHz to 110 GHz broadband millimeter-wave system provides high performance and capabilities including power control, 4-port true-differential, and frequency converter
measurements. It is configured with an N5227A PNA with Option 201 (2-ports) or Option 401 (4-ports), or N5247A with Option 200 (2-ports) or Option 400 (4-ports), Option 020 IF access, an N5261A 2-port or an N5262A 4-port millimeter-wave test set controller with 1.85 mm coaxial cables (Option 112 for N5261A, Option 114 for N5262A) and RF/LO/IF/DC cables sets (to select the cable length and quantities), and one (for 2-ports) or two (for 4-ports) each of right and left frequency extenders with required attenuators and bias-tee configurations.
□Waveguide banded solutions to 1.05 THz
Interface kit for test set with jumper connectors to align with N524xA PNA-X and N522xA PNA
Interface kit for test set with jumper connectors to align with E836xB/C PNA and N5230A/C-x25 2-port PNA-L
For use with E8361A/C 2-port PNA
For use with E8362B/C 2-port PNA or N5230A/C-225 2-port PNA-L
For use with E8363B/3C/4B/4C 2-port PNA or N5230A/C-425/525 2-port PNA-L
For use with N5230A/C-245/246 4-port PNA-L
For use with N5241/42/49A-2xx 2-port PNA-X or N5221A/2A-2xx 2-port PNA
For use with N5241/42/49A-400 4-port PNA-X or N5221A/2A-4xx 4-port PNA
For use with N5244A/5A-200 2-port PNA-X or N5224A/5A-2xx 2-port PNA
For use with N5244A/5A-400 4-port PNA-X or N5224A/5A-4xx 4-port PNA
For use with N5247A-200 2-port PNA-X or N5227A-2xx 2-port PNA
For use with N5247A-400 4-port PNA-X or N5227A-4xx 4-port PNA
The waveguide banded millimeter-wave solution covers wave-
guide bands from 50 GHz to 1.05 THz. A 2- or 4-port PNA or PNA-X in conjunction with N5261A (for 2-port) or N5262A
(for 4-port) configures for the most complete millimeter wave solution. It is configured with a PNA Series with Option 020 IF access, configurable test set (Option 201 or 401), and fre-
quency offset mode (Option 080), or PNA-X Series with 2-port (Option 200) or 4-port (Option 400) and IF access (Option 020). For the millimeter-wave test controller, appropriate RF cable option and RF/LO/IF/DC cable set option for frequency extenders must be selected for the analyzer’s connector type, number of test ports, and lengths. Add appropriate frequency extenders with required quantity for the measurements.
For complete list of millimeter-wave products and options, and
ordering instructions, please refer to 5989-7620EN Millimeterwave Network Analyzers Technical Overview.
When ordering an additional cable set, a spare cable or rear
locking feet, refer to the multiport test set user’s guide or go to:
www.agilent.com/find/multiport
23
Measurement Accessories
A complete list of RF and microwave test accessories
is available on our Web site:
www.agilent.com/find/accessories
Accessories are available in these connector types:
50 ohm Type-N, 3.5 mm, 7 mm, 2.4 mm, 2.92 mm, 1.85 mm, 1.0 mm,
and waveguide. Test port cables and a calibration kit should be
added for a complete measurement system. A verification kit is
used to verify corrected system performance.
Cables and adapter sets
Agilent offers cables in the following types:
• single cables in semi-rigid and flexible
• cable sets in semi-rigid and flexible
There are also adapter sets available that protect the test port
and convert the port to the desired connector interface. These
kits contain:
• one male adapter • one female adapter To attain the best mechanical rigidity for device connection, use
a single cable and the appropriate special adapter set. To attain
the greatest flexibility for device connection, use a cable set.
Network analyzer
test set
Device
under
test
Network analyzer
test set
Coaxial measurements
Mechanical calibration kits include standards, such
as opens, shorts and loads, which are measured by the network
analyzer for increased measurement accuracy.
Electronic calibration (ECal) kits replace mechanical calibration
standards with one solid-state calibration module that is controlled by the network analyzer via USB, to present many different impedances to the test ports. A full two-port calibration can
be performed quickly with a single connection. This technique
reduces operator errors and connector wear and abrasion.
Choose a calibration kit for each connector type to be used.
Economy, includes:
• open standards (male and female)
• short standards (male and female)
• fixed-termination standards (male and female)
Standard, includes the devices in the economy kit and adds:
• sliding load standards (male and female) or a series of offset shorts
Precision, includes the devices in the economy kit and adds:
• 50 ohm airline(s) for TRL calibration
• TRL adapters
Waveguide measurements
Test port
adapter
Cable set
Single cable
Calibration kits
Device
under
test
For waveguide measurements, Agilent offers mechanical calibration
kits that include:
• waveguide-to-coax adapters (X, P, K, R, Q, U, V)
• precision waveguide section
• flush short circuit
• fixed terminations
• straight section
For devices with 1.0 mm connectors
For devices with 1.85 mm connectors
Mechanical calibration/verification kit
Mechanical calibration kits
kit.
Includes:
85059-60003
85059-60007
85059-60004
85059-60008
85059-60002
85059-60006
85059-60001
85059-60005
85059-60009
85059-60010
85059-60019
85059-60020
85059-60021
11920-60001
11920-60002
11920-60003
11500-60001
85059-60016
85059-60017
8710-2079
8710-2156
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60102 1.85 mm (m) short 6.3 mm
85058-60103 1.85 mm (m) short 7.12 mm
85058-60104 1.85 mm (m) short 7.6 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60106 1.85 mm (f) short 6.3 mm
85058-60107 1.85 mm (f) short 7.12 mm
85058-60108 1.85 mm (f) short 7.6 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60111 1.85 mm male load
85058-60112 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
□85059A DC to 110 GHz precision calibration/verification
1.00 mm (m) short 2.450 mm
1.00 mm (f) short 2.450 mm
1.00 mm (m) short 3.000 mm
1.00 mm (f) short 3.000 mm
1.00 mm (m) short 1.825 mm
1.00 mm (f) short 1.825 mm
1.00 mm (m) short 1.300 mm
1.00 mm (f) short 1.300 mm
1.00 mm male open
1.00 mm female open
1.00 mm male load
1.00 mm female load
1.00 mm lossy delay line
1.00 mm (m) to 1.00 mm (m) adapter
1.00 mm (f) to 1.00 mm (f) adapter
1.00 mm (m) to 1.00 mm (f) adapter
1.00 mm (f) to 1.00 mm (f) 8.8 cm cable
1.00 mm mismatch thru adapter
for verification
1.00 mm matched thru adapter
for verification
6 mm, 4 in-lb torque wrench
6 mm open end wrench
Cables
□11500I 1.0 mm (f-f) test port cable (8.8 cm)
□11500J 1.0 mm (m-f) test port cable (16.0 cm)1
□11500K 1.0 mm (m-f) test port cable (20.0 cm)1
□11500L 1.0 mm (m-f) test port cable (24.0 cm)1
Adapter set
□V281C 1.0 mm(f) to V-band waveguide adapter
□V281D 1.0 mm (m) to V-band waveguide adapter
□W281C 1.0 mm (f) to W-band waveguide adapter
□W281D 1.0 mm (m) to W-band waveguide adapter
□11920A 1.0 mm (m) to 1.0 mm (m) adapter
□11920B 1.0 mm (f) to 1.0 mm (f) adapter
□11920C 1.0 mm (m) to 1.0 mm (f) adapter
□11921A 1.0 mm (m) to 1.85 mm (m) adapter
□11921B 1.0 mm (f) to 1.85 mm (f) adapter
□11921C 1.0 mm (m) to 1.85 mm (f) adapter
□11921D 1.0 mm (f) to 1.85 mm (m) adapter
□11922A 1.0 mm (m) to 2.4 mm (m) adapter
□11922B 1.0 mm (f) to 2.4 mm (f) adapter
□11922C 1.0 mm (m) to 2.4 mm (f) adapter
□11922D 1.0 mm (f) to 2.4 mm (m) adapter
□11923A 1.0 mm (f) connector launch assembly
1. For on-wafer applications, two 11500J/K/L cables are required;
one cable for each test port.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
□85058B standard: DC to 67 GHz.
□85058E economy: DC to 67 GHz.
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60123 1.85 mm male load
85058-60124 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
Electronic calibration kits
□N4694A Microwave ECal: 10 MHz to 67 GHz, 2-ports. Includes:
Option M0F module with:
N4694-60001 1.85 mm (f) to 1.85 mm (m) ECal module
Option 00M module with:
N4694-60002 1.85 mm (m) to 1.85 mm (m) ECal module
Option 00F module with:
N4694-60003 1.85 mm (f) to 1.85 mm (f) ECal module
Option 00A adds:
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
Cables
□N4697E2 Single, flexible: 1.85 mm (f) to 1.85 mm (f),
96.5 cm, 38 inches
□N4697F2 Set, flexible:
One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm,
24.5 inches, p/n N4697-60100
One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm,
24.5 inches, p/n N4697-60200
□N4421B-K67 Single, flexible: 1.85 mm (f) to
1.85 mm (m), 91.4 cm, 36 inches
Adapter set
□85130H2 1.85 mm to 1.85 mm
For devices with 2.4 mm connectors
Mechanical calibration kits
□85056A standard: DC to 50 GHz.
Includes:
00901-60003 2.4 mm (m) fixed broadband load
00902-60004 2.4 mm (f) fixed broadband load
00915-60003 2.4 mm (m) sliding load
00915-60004 2.4 mm (f) sliding load
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
85056-60020 2.4 mm (m) short
85056-60021 2.4 mm (f) short
85056-60022 2.4 mm (m) open
85056-60023 2.4 mm (f) open
□85056D economy: DC to 50 GHz.
Includes:
00901-60003 2.4 mm (m) fixed broadband load
00902-60004 2.4 mm (f) fixed broadband load
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
85056-60007 2.4 mm (m) to 2.4 mm (f) adapter
85056-60020 2.4 mm (m) short
85056-60021 2.4 mm (f) short
85056-60022 2.4 mm (m) open
85056-60023 2.4 mm (f) open
Electronic calibration kits
□N4693A Microwave ECal: 10 MHz to 50 GHz, 2-ports. Includes:
Option M0F module with:
N4693-60001 2.4 mm (f) to 2.4 mm (m) ECal module
Option 00M module with:
N4693-60002 2.4 mm (m) to 2.4 mm (m) ECal module
Option 00F module with:
N4693-60003 2.4 mm (f) to 2.4 mm (f) ECal module
Option 00A adds:
85056-60005 2.4 mm (m) to 2.4 mm (m) adapter
85056-60006 2.4 mm (f) to 2.4 mm (f) adapter
Cables
Note: Agilent offers the following 2.4 mm test port cables. Adapters will
be necessary when using these cables for 2.92 mm measurements.
□85133C1single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
81 cm, 32 inches
□85133D1set, semi-rigid:
One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
□85133E1single, flexible: 2.4 mm (f) to PSC-2.4 mm (f), 97 cm, 38 inches
□85133F1set, flexible:
One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
□85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
63 cm, 25 inches
□N4421AK20 Single, flexible: 2.4 mm (f) to 2.4 mm (m), 91.4 cm, 36 inches
1. Special rugged female connector specifically for connecting
to the network analyzer test port, but does not mate with a standard male connector.
2. Special rugged female connector specifically for connecting
to the network analyzers NMD 2.4 mm test port, but does
not mate with standard 2.4 mm male connector
Adapter set
□85130F 2.4 mm1 to 3.5 mm
□85130F 2.5 mm1 to 3.5 mm
□85130G 2.4 mm1 to 2.4 mm
For devices with K connectors (2.92 mm)
Mechanical calibration kits
□85056KE01 DC to 40 GHz
For use with user supplied 2.9 mm test port cables. 2.92 mm
(K connector) calibration kit with fixed and sliding loads. The
Agilent 85056KE01 calibration kit is an ordering convenience
to allow the pass through ordering from Agilent Technologies,
Inc. for the Maury 8770C47 calibration kit.
□85056KE02 DC to 40 GHz
For use with user supplied 2.92 mm test ports cables. 2.92 mm
(K connector) calibration kit with fixed loads only. The Agilent
85056KE02 calibration kit is an ordering convenience to allow
the pass through ordering from Agilent Technologies, Inc. for
the Maury 8770D47 calibration kit.
The 85056KE01 and 85056KE02 contains one NMD 2.4 mm2 (f)
to 2.92 mm (f) and one NMD 2.4 mm2 (f) to 2.92 mm (m) test
port adapter to adapt the 2.4 mm test ports of the PNA to 2.92
mm. It also supplies 2.92 mm to 2.92 mm in-series adapters (3
adapters) and a PNA Cal Coefficients on a USB stick. Users
must supply their own 2.92 mm or K-connector test port
cables. Also included is a 2.92 mm torque wrench.
Maury Microwave Terms and Conditions for Warranty and
Return apply. Maury Microwave Corp. calibration kits are to be
returned directly to Maury Microwave for service, repair, or
calibration issues and not to Agilent Technologies. For additional information go to www.maurymicrowave.com.
Agilent Technologies does not guarantee the performance of
the Maury calibration kits or the system performance when
connected to Agilent Microwave PNA Series network analyzers.
Electronic calibration kits
□N4692A Microwave ECal: 10 MHz to 40 GHz, 2-ports. Includes:
Option M0F module with:
N4692-60001 2.92 mm (f) to 2.92 mm (m) ECal module
Option 00M module with:
N4692-60002 2.92 mm (m) to 2.92 mm (m) ECal module
Option 00F module with:
N4692-60003 2.92 mm (f) to 2.92 mm (f) ECal module
Option 00A adds:
N4692-60021 2.92 mm (m) to 2.92 mm (m) adapter
N4692-60022 2.92 mm (f) to 2.92 mm (f) adapter
Cables
For devices with 3.5 mm, SMA, or
2.92 mm connectors
Note: Agilent offers the following 2.4 mm test port cables. Adapters will
be necessary when using these cables for 2.92 mm measurements.
□85133C1single, semi-rigid: 2.4 mm (f) to PSC-2.4 mm (f),
CalPod calibration refresh modules
81 cm, 32 inches
□85133D1set, semi-rigid:
One 2.4 mm (f) to 2.4 mm (m), 53 cm, 21 inches,
p/n 85133-60001
One 2.4 mm (f) to 2.4 mm (f), 53 cm, 21 inches,
p/n 85133-60002
□85133E1single, flexible: 2.4 mm (f) to PSC-2.4 mm (f), 97 cm, 38 inches
□85133F1set, flexible:
One 2.4 mm (f) to 2.4 mm (f), 63 cm, 25 inches,
p/n 85133-60016
One 2.4 mm (f) to 2.4 mm (m), 63 cm, 25 inches,
p/n 85133-60017
□85133H1 Single, flexible: 2.4 mm (f) to 2.4 mm (m),
63 cm, 25 inches
□N4421AK20 Single, flexible: 2.4 mm (f) to 2.4 mm (m), 91.4 cm, 36 inches
CalPod calibration refresh modules allow in-situ calibration
refreshes to be performed at the push of a button without removing the DUT or connecting calibration standards. They're useful
for removing environmental effects such as cable movement,
thermal effects of cables, connectors, and adapters, as well as
connector and switch matrix repeatability errors, or whenever it
is desirable to ensure a current and valid calibration is present.
The modules are especially useful in thermal or thermal-vacuum
chamber testing.
□85530B 20 GHz Ambient temperature CalPod calibration refresh module
□85531B 20 GHz Temperature-compensated CalPod calibration refresh module
□85532B 20 GHz Thermal-vacuum compatible CalPod calibration refresh module
□85540A 40 GHz Ambient temperature CalPod calibration refresh module
□85541A 40 GHz Temperature-compensated CalPod calibration refresh module
□85542A 40 GHz Thermal-vacuum compatible CalPod
calibration refresh module
□85523B CalPod controller
Provides control for up to four CalPods
□85556A CalPod drive cable splitter
Allows control for up to 12 CalPods
□85554A CalPod drive cable extension
10 meter extension cable; cascadable.
Adapters
□11904A 2.4 mm (m) to 2.92 mm (m)
□11904B 2.4 mm (f) to 2.92 mm (f)
□11904C 2.4 mm (m) to 2.92 mm (f)
□11904D 2.4 mm (f) to 2.92 mm (m)
□11904S 2.4 mm to 2.92 mm
Adapter set, contains 4 matched adapters
1. Special rugged female connector specifically for connecting
to the network analyzer test port, but does not mate with a standard male connector.
27
For devices with 3.5 mm or SMA
connectors
85093C-xxx mixed-connector options:
Mechanical calibration kits
□85052B standard: DC to 26.5 GHz.
Port A option
Port B option
Type (f) (m) Type (f) (m) Type(f) (m)
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
00911-60019 3.5 mm (m) sliding load
00911-60020 3.5 mm (f) sliding load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
3.5 mm 101
102
Type-N 203
50 ohm
204
7-16
205
206
□N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4-ports.
Includes:
Option 010 module with:
N4431-60006 4 x 3.5 mm (f) ECal module
N4431B-xxx mixed-connector options:
□85052C precision TRL: DC to 26.5 GHz.
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60032 3.5 mm (f) to 3.5 mm (f) adapter
85052-60033 3.5 mm (m) to 3.5 mm (m) adapter
85052-60034 3.5 mm (f) to 3.5 mm (m) adapter
85052-60035 3.5 mm short TRL line
85052-60036 3.5 mm long TRL line
Connector type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Port A option
101
102
103
Port B option
201
202
203
Port C
option
301
302
303
Port D
option
401
402
403
Type-N 50 ohm (m)
7-16 (f)
7-16 (m)
104
105
106
204
205
206
304
305
306
404
405
406
□N4433A Microwave ECal: 300 kHz to 20 GHz, 4-ports.
Includes:
□Option 010 module with:
N4433-60003 4 x 3.5 mm (f) ECal module
N4433A-xxx mixed-connector options:
Connector type
3.5 mm (f)
3.5 mm (m)
□85052D economy: DC to 26.5 GHz.
Includes:
00902-60003 3.5 mm (m) fixed load
00902-60004 3.5 mm (f) fixed load
85052-60006 3.5 mm (m) short
85052-60007 3.5 mm (f) short
85052-60008 3.5 mm (m) open
85052-60009 3.5 mm (f) open
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60013 3.5 mm (f) to 3.5 mm (m) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
Port A option
101
102
Port B option
201
202
Port C
option
301
302
Port D
option
401
402
□N4691B Microwave ECal: 300 kHz to 26.5 GHz, 2-ports. Includes:
Option M0F module with:
N4691-60004 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00M module with:
N4691-60005 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00F module with:
N4691-60006 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00A adds:
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
Electronic calibration kits
□85093C RF ECal: 300 kHz to 9 GHz, 2-ports
Standard module includes
Option M0F with:
85093-60008 3.5 mm (f) to 3.5 mm (m) ECal module
Option 00F module with:
85093-60010 3.5 mm (f) to 3.5 mm (f) ECal module
Option 00M module with:
85093-60009 3.5 mm (m) to 3.5 mm (m) ECal module
Option 00A adds:
85052-60012 3.5 mm (f) to 3.5 mm (f) adapter
85052-60014 3.5 mm (m) to 3.5 mm (m) adapter
Cables
□85131C1single, semi-rigid: 3.5 mm (f) to PSC-3.5 mm (f), 81 cm, 32 inches2
□85131D1 set, semi-rigid:
One 3.5 mm (f) to 3.5 mm (m), 53 cm, 21 inches,
p/n 85131-60009
One 3.5 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches, p/n 85131-60010
□85131E1 single, flexible: 3.5 mm (f) to PSC-3.5 mm (f), 96.5 cm, 38 inches2
□85131F1 set, flexible:
One 3.5 mm (f) to 3.5 mm (m), 62.2 cm, 24.5 inches, p/n 85131-60012
One 3.5 mm (f) to PSC-3.5 mm (f), 62.2 cm, 24.5 inches, p/n 85131-60013
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
2. For use with E8362C.
28
□85131H1 single, flexible: 3.5 mm (f) to 3.5 mm (m),
Electronic calibration kits
62.2 cm, 24.5 inches
□85134E1 single, flexible: PSC-3.5 mm (f) to 2.4 mm (f), 96 cm, 38 inches
□85134F1 set, flexible:
One 2.4 mm (f) to PSC-3.5 mm (f), 53 cm, 21 inches, p/n 85134-60004
One 2.4 mm (f) to PSC-3.5 mm (m), 53 cm, 21 inches, p/n 85134-60003
□85134H1 single, flexible: 2.4 mm (f) to PSC-3.5 mm (m),
53 cm, 21 inches
□N4419AK20 single, flexible: 3.5 mm (m) to 3.5 mm (f),
91.4 cm, 36 inches
□Z5623A-K20 single, flexible: 3.5 mm (m) to 3.5 mm (m),
91.4 cm, 36 inches
□N4431B Microwave ECal: 300 kHz to 13.5 GHz, 4-ports.
Includes:
Option 020 module with:
N4431-60007 4 x Type-N (f) ECal module
N4431B-xxx mixed-connector options:
Connector type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Type-N 50 ohm (m)
7-16 (f)1
7-16 (m)1
Adapter sets
□85130D 3.5 mm1 to 3.5 mm
Port A option
101
102
103
104
105
106
Port B option
201
202
203
204
205
206
Port C
Port D
option
option
301
401
302
402
303
403
304
404
305405
306406
□N4432A Microwave ECal: 300 kHz to 18 GHz, 4-ports.
For devices with Type-N connectors
Includes:
Option 020 module with:
N4432-60003 4 x Type-N (f) ECal module
Mechanical calibration kits
□85054B standard: DC to 18 GHz.
N4432A-xxx mixed-connector options:
Includes:
00909-60011 Type-N (m) fixed lowband load
00909-60012 Type-N (f) fixed lowband load
85054-60025 Type-N (m) short
85054-60026 Type-N (f) short
85054-60027 Type-N (m) open
85054-60028 Type-N (f) open
85054-60031 Type-N (f) to 7mm adapter
85054-60032 Type-N (m) to 7mm adapter
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
85054-80010 Type-N (f) sliding load
85054-80009 Type-N (m) sliding load
85054-60050 Type-N (f) connector gage
85054-60052 Type-N (f) gage master
85054-60051 Type-N (m) connector gage
85054-60053 Type-N (m) gage master
Connector type
3.5 mm (f)
3.5 mm (m)
Type-N 50 ohm (f)
Type-N 50 ohm (m)
Port A option
101
102
103
104
Port B option
201
202
203
204
Port C
option
301
302
303
304
Port D
option
401
402
403
404
□N4690B Microwave ECal: 300 kHz to 18 GHz, 2-ports. Includes:
Option M0F module with:
N4690-60004 Type-N (f) to Type-N (m) ECal module
Option 00M module with:
N4690-60005 Type-N (m) to Type-N (m) ECal module
Option 00F module with:
N4690-60006 Type-N (f) to Type-N (f) ECal module
Option 00A adds:
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
□85054D economy: DC to 18 GHz.
Includes:
85054-60025 Type-N (m) short
85054-60026 Type-N (f) short
85054-60027 Type-N (m) open
85054-60028 Type-N (f) open
85054-60031 Type-N (f) to 7mm adapter
85054-60032 Type-N (m) to 7mm adapter
85054-60037 Type-N (f) to Type-N (f) adapter
85054-60038 Type-N (m) to Type-N (m) adapter
85054-60046 Type-N (m) fixed load
85054-60047 Type-N (f) fixed load
Cables 2
Use the test port cables recommended for devices with 7 mm
connectors, and 7 mm to Type-N adapters that are from the
85054B/D Type-N calibration kit (see 7 mm connector section).
Adapter sets
□85130C 3.5 mm2 to Type-N
1. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
2. For use with E8362C.
29
For devices with 7 mm connectors
For devices with waveguide
Mechanical calibration kits
Mechanical calibration kits
Includes:
00909-60008 7 mm coax termination
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
85050-80011 7 mm sliding load
X Band
□85050B standard: DC to 18 GHz.
□85050C precision TRL: DC to 18 GHz.
Includes:
00909-60008 7 mm coax termination
85050-60003 7 mm to 7 mm airline
85050-60005 7 mm to 7 mm TRL adapter
85050-60006 7 mm fixed broadband load
85050-80008 7 mm short
85050-80009 7 mm short collet
85050-80010 7 mm open
□X11644A standard, WR-90: 8.2 to 12.4 GHz. Includes:
00896-60008 X-band standard section
00910-60003 X-band termination
11644-20018 X-band short
11644-20021 X-band shim
□85132F cable set (set, flexible 3.5 mm (f) to 7 mm,
62.9 cm each, 24.75 inches each2)
□85135F cable set (set, flexible,
2.4 mm (f) to 7 mm, 53 cm each, 21 inches each)
□X281C adapter (included in calibration kit):
WR-90 to 7 mm
P Band
□P11644A standard, WR-62: 12.4 to 18 GHz.
7mm to 7mm Microwave module
Includes:
00896-60007 P-band standard section
00910-60002 P-band termination
11644-20017 P-band short
11644-20020 P-band shim
□85132F cable set (set, flexible, 3.5 mm (f) to 7 mm,
62.9 cm each, 24.75 inches each2)
□85135F cable set (set, flexible, 2.4 mm (f) to 7 mm,
53 cm each, 21 inches each)
□P281C adapter (included in calibration kit):
WR-62 to 7 mm
Cables 1
K Band
97.2 cm, 38.25 inches2
□85132F set, flexible: two 3.5 mm (f) to 7 mm cables, 62.9 cm each, 24.75 inches each2, p/n 85132-60004
□85135E single, flexible: 2.4 mm (f) to 7 mm,
96 cm, 38 inches
□85135F set, flexible: two 2.4 mm (f) to 7 mm cables,
53 cm each, 21 inches each, p/n 85135-60002
Includes:
00896-60006 K-band standard section
00910-60001 K-band termination
11644-20016 K-band short
11644-20019 K-band shim
□85134F cable set (set, flexible, 2.4 mm (f) to 3.5 mm (f) and (m),
53 cm each, 21 inches each)
□K281C adapter (included in calibration kit):
WR-42 to 3.5 mm (f)
Option 012 WR-42 to 3.5 mm (m)
□85050D economy: DC to 18 GHz.
Includes:
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
Electronic calibration kits
□N4696B Microwave ECal: 300 kHz to 18 GHz, 2-ports, □85132E single, flexible: 3.5 mm (f) to 7 mm,
Adapter sets
□85130E 2.4 mm1 to 7 mm
□K11644A standard, WR-42: 18 to 26.5 GHz.
R Band
□R11644A standard, WR-28: 26.5 to 40 GHz.
Includes:
00914-20028 R-band termination
11644-20005 R-band short
11644-20003 R-band shim
11644-60001 R-band 10 cm straight waveguide
11644-60016 R-band 5 cm straight waveguide
□85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
□R281A adapter (2.4 mm (f) to WR-28 waveguide adapter)
□R281B adapter (2.4 mm (m) to WR-28 waveguide adapter)
1. For use with E8362C.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard
male connector.
30
Q Band
Verification kits
Includes:
11644-60005 Q-band termination
11644-20004 Q-band short
11644-20001 Q-band shim
11644-60002 Q-band 10 cm straight waveguide
11644-60017 Q-band 5 cm straight waveguide
□85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
□Q281A adapter (2.4 mm (f) to WR-22 waveguide adapter)
□Q281B adapter (2.4 mm (m) to WR-22 waveguide adapter)
All Agilent verification kits include:
• precision Z0 airline or match thru
• mismatched airline or mismatch thru
• fixed attenuators
• traceable measured data and uncertainties
U Band
□85053B 300 kHz to 26.5 GHz 3.5 mm kit
□Q11644A standard, WR-22: 33 to 50 GHz.
□U11644A standard, WR-19: 40 to 60 GHz.
Includes:
11644-60006 U-band termination
11644-20004 U-band short
11644-20002 U-band shim
11644-60003 U-band 10 cm straight waveguide
11644-60018 U-band 5 cm straight waveguide
V Band
□V11644A standard, WR-15: 50 to 75 GHz.
Includes:
11644-60025 V-band termination
11644-20015 V/W-band short
11644-20013 V-band shim
11644-60012 V-band standard section
W Band
□W11644A standard, WR-10: 75 to 110 GHz.
Includes:
11643-60026 W-band termination
11644-20015 V/W-band short
11644-20014 W-band shim
11644-60013 W-band standard section
□85051B 45 MHz to 18 GHz 7 mm kit
Includes attenuators, airline and mismatch airline with data on a 3.5-inch disk for use in confirming accuracy enhanced system
measurement performance, traceable to national standards.
Test procedure is provided in the service manual.
Includes attenuators, airline and mismatch airline with data on a 3.5-inch disk for use in confirming accuracy enhanced system measurement performance, traceable to national standards. Test procedure is provided in the service manual.
□85055A 300 kHz to 18 GHz Type-N kit
Includes attenuators, airline and mismatch airline with data on a 3.5-inch disk for use in confirming accuracy enhanced system measurement performance, traceable to national standards. Test procedure is provided in the service manual.
□85057B 45 MHz to 50 GHz 2.4 mm kit
Includes attenuators, airline and mismatch airline with data on a 3.5-inch disk for use in confirming accuracy enhanced system measurement performance, traceable to national standards. Test procedure is provided in the service manual.
□85058V 45 MHz to 67 GHz 1.85 mm kit
31
Includes attenuators, match thru and mismatch thru with data on a 3.5-inch disk for use in confirming accuracy enhanced
system measurement performance, traceable to national
standards. Test procedure is provided in the service manual.
General Accessories
Comb generators
□N8981A spare solid-state drive with mounting cradle
□U9391C 10 MHz to 26.5 GHz comb generator
□U9391F 10 MHz to 50 GHz comb generator
□U9391G 10 MHz to 67 GHz comb generator
1
Spare drive
Two are required for NVNA. Also requires separate power supply.
For E836xA/B and N5230A.
□N8982A spare solid-state drive with mounting cradle
For E836xC and N5230C.
□N8983A spare solid-state drive with mounting cradle
For all PNAs with Windows 7 currently installed
□N5242-60044 spare solid-state drive with mounting cradle
For N524xA with 2.0 GHz Core 2 Duo CPU.
□N5242-60088 spare solid-state drive with mounting cradle
For N522xA/4xA with 2.0 GHz Core i7 CPU.
□N5235-60060 spare solid-state drive with mounting cradle
For N523xA with 1.87 GHz Celeron CPU.
Spare solid-state drive for N5242A/1A with 1.6 GHz Pentium M
CPU is discontinued. Upgrading to 2.0 GHz Core i7 CPU (W131260196) is recommended.
Amplifiers
□83006A power amplifier, 10 MHz to 26.5 GHz, 20 dB gain, power out: +18 dBm to 10 GHz or +16 dBm to 20 GHz or
+14 dBm to 26.5 GHz
□83017A power amplifier, 50 MHz to 26.5 GHz, 25 dB gain, power out: +20 dBm to 20 GHz, or +15 dBm to 26.5 GHz
□83018A power amplifier, 2 to 26.5 GHz, 27 dB gain to 20 GHz or 23 dB to 26.5 GHz, power out: +24 dBm to 20 GHz or
+21 dBm to 26.5 GHz
□83020A power amplifier, 2 to 26.5 GHz, 30 dB gain to 20 GHz or 27 dB to 26.5 GHz, power out: +30 dBm to 20 GHz or
+26 dBm to 26.5 GHz
□83050A power amplifier, 2 to 50 GHz, 23 dB gain, power out: +20 dBm to 40 GHz or +17 dBm to 50 GHz
□83051A power amplifier, 45 MHz to 50 GHz, 23 dB gain power out: +12 dBm to 45 GHz or +10 dBm to 50 GHz
Probe
□85024A high-frequency probe
Provides high-impedance in-circuit test capability from
300 kHz to 3 GHz.
Couplers
2
Power meters and sensors
□87300B coaxial coupler, 1 to 20 GHz, SMA (f), 10 dB coupling
□87300C coaxial coupler, 1 to 26.5 GHz, 3.5 mm (f), 10 dB coupling
□87301B coaxial coupler, 10 to 46 GHz, 2.92 mm (f), 10 dB coupling
□87301D coaxial coupler, 1 to 40 GHz, 2.4 mm (f) or optional Recommended for self support, adjustments and performance
tests to verify proper instrument operation.
□N1913A EPM power meter (single channel)
□N1914A EPM power meter (dual channel)
□N8481A power sensor, 10 MHz to 18 GHz, -35 to +20 dBm
□N8481B power sensor, 10 MHz to 18 GHz, -5 to +44 dBm
□N8481H power sensor, 10 MHz to 18 GHz, -15 to +35 dBm
□N8482A power sensor, 100 kHz to 6 GHz, -35 to +20 dBm
□N8482B power sensor, 100 kHz to 6 GHz, -5 to +44 dBm
□N8482H power sensor, 100 kHz to 6 GHz, -15 to +35 dBm
□N8485A power sensor, 50 MHz to 26.5 GHz, -35 to +20 dBm
□N8485A-033 average power, 10 MHz to 33 GHz, -35 to +20 dBm, 2.92 mm (f), 13 dB coupling
□87301E coaxial coupler, 2 to 50 GHz, 2.4 mm (f), 10 dB coupling
□87310B 90o coaxial coupler, 1 to 18 GHz, SMA (f), 3 dB coupling
Equipment rack accessories
□E3663AC Rail kit (included with Option 1CM and 1CP)
□ICM042A Rack mount kit, for use without handles (included with Option 1CM)
□5063-9224 Rack mount kit with handles3
□5063-9230 Front handle kit3
3.5 mm (m)
□N8486AQ waveguide, 33 to 50 GHz, -35 to +20 dBm
□N8486AR waveguide, 26.5 to 40 GHz, -35 to +20 dBm
□N8487A power sensor, 50 MHz to 50 GHz, -35 to +20 dBm
□N8488A power sensor, 10 MHz to 67 GHz, -35 to +20 dBm
□V8486A waveguide power sensor, 50 to 75 GHz , -30 to +20 dBm
□W8486A waveguide power sensor, 75 to 110 GHz , -30 to +20 dBm
□U2000A USB sensor, 10 MHz to 18 GHz, -60 to +20 dBm
□U2000B USB sensor, 10 MHz to 18 GHz, -30 to +44 dBm
□U2000H USB sensor, 10 MHz to 18 GHz, -50 to +30 dBm
□U2001A USB sensor, 10 MHz to 6 GHz, -60 to +20 dBm
□U2001B USB sensor, 10 MHz to 6 GHz, -30 to +44 dBm
□U2001H USB sensor, 10 MHz to 6 GHz, -50 to +30 dBm
□U2002A USB sensor, 50 MHz to 24 GHz, -60 to +20 dBm
□U2002A-H26 USB sensor, 10 MHz to 26.5 GHz, -60 to +20 dBm
□U2002H USB sensor, 50 MHz to 24 GHz, -50 to +30 dBm
□U2004A USB sensor, 9 kHz to 6 GHz, -60 to +20 dBm
□E4412A CW power sensor, 10 MHz to 18 GHz, -70 to +20 dBm
□E4413A CW power sensor, 50 MHz to 26.5 GHz, -70 to +20 dBm
□E4413A-H33 specified performance for 50 MHz to 33 GHz
□5063-9237 Rack mount kit, for use with classic handles (included with Option 1CP)3
Monitors
VGA-compatible monitor
Interface cables
Choose the appropriate cables to connect each
peripheral to the network analyzer.
□10833A GPIB cable, 1.0 m (3.3 ft)
□10833B GPIB cable, 2.0 m (6.6 ft)
□10833D GPIB cable, 0.5 m (1.6 ft)
□ 82357B GPIB to USB interface
1. For more information on solid-state drive, refer to na.tm.agilent.com/pna/hdnumbers.html
2. For the latest guide to power meters and power sensors, refer to the Agilent web site: www.agilent.com/find/powermeters
3. 5063-9224 is a complete rack mount kit with handles. N52xxA comes with ruggedized handles, which must be replaced with classic handles shipped with the kit. 5063-9230 is a pair of classic handles, and used with 5063-9237 for mounting N52xxA to a rack.
32
www.agilent.com
www.agilent.com/find/pna
myAgilent
myAgilent
www.agilent.com/find/myagilent
A personalized view into the information most relevant to you.
www.axiestandard.org
AdvancedTCA® Extensions for Instrumentation and Test (AXIe)
is an open standard that extends the AdvancedTCA for general
purpose and semiconductor test. Agilent is a founding member of
the AXIe consortium.
www.lxistandard.org
LAN eXtensions for Instruments puts the power of Ethernet and the
Web inside your test systems. Agilent is a founding member of the
LXI consortium.
Three-Year Warranty
www.agilent.com/find/ThreeYearWarranty
Beyond product specification, changing the ownership experience.
Agilent is the only test and measurement company that offers
three-year warranty on all instruments, worldwide.
Agilent Assurance Plans
www.agilent.com/find/AssurancePlans
Five years of protection and no budgetary surprises to ensure your
instruments are operating to specifications and you can continually
rely on accurate measurements.
www.agilent.com/quality
Agilent Electronic Measurement Group
DEKRA Certified ISO 9001:2008
Quality Management System
Agilent Channel Partners
www.agilent.com/find/channelpartners
Get the best of both worlds: Agilent’s measurement expertise and
product breadth, combined with channel partner convenience.
For more information on Agilent
Technologies’ products, applications or
services, please contact your local Agilent
office. The complete list is available at:
www.agilent.com/find/contactus
Americas
Canada
Brazil Mexico
United States
(877) 894 4414
(11) 4197 3600
01800 5064 800
(800) 829 4444
Asia Pacific
Australia 1 800 629 485
China
800 810 0189
Hong Kong 800 938 693
India 1 800 112 929
Japan
0120 (421) 345
Korea
080 769 0800
Malaysia 1 800 888 848
Singapore 1 800 375 8100
Taiwan
0800 047 866
Other AP Countries (65) 375 8100
Europe & Middle East
Belgium 32 (0) 2 404 93 40
Denmark
45 45 80 12 15
Finland
358 (0) 10 855 2100
France
0825 010 700*
*0.125 €/minute
Germany
49 (0) 7031 464 6333
Ireland
1890 924 204
Israel972-3-9288-504/544
Italy
39 02 92 60 8484
Netherlands
31 (0) 20 547 2111
Spain
34 (91) 631 3300
Sweden
0200-88 22 55
United Kingdom 44 (0) 118 927 6201
For other unlisted countries:
www.agilent.com/find/contactus
(BP-01-15-14)
Product specifications and descriptions in
this document subject to change without
notice.
Pentium® is a U.S. registered trademark of Intel Corporation.
© Agilent Technologies, Inc. 2012-2014
Published in USA, March 31, 2014
5990-7745EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising