PA700 User Manual
PA700 Rugged Handheld Computer
User’s Manual
Version 1.1
Preface
About This Manual
Thank you for purchasing the unitech product.
This manual explains how to install, operate and maintain our product.
No part of this publication may be reproduced or used in any form, or by any
electrical or mechanical means, such as photocopying, recording, or
information storage and retrieval systems, without permission in writing from
the manufacturer. The material in this manual is subject to change without
notice.
Regulatory Compliance Statements
FCC Warning Statement
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference with radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
1. This transmitter must not be co-located or operating in conjunction
i
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
2.
3.
with any other antenna or transmitter.
This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
Any changes or modifications (including the antennas) made to this device
that are not expressly approved by the manufacturer may void the user’s
authority to operate the equipment.
Operation on the 5.15 - 5.25GHz frequency band is restricted to indoor use
only. The FCC requires indoor use for the 5.15-5.25GHz band to reduce the
potential for harmful interference to co-channel Mobile Satellite Systems.
Therefore, it will only transmit on the 5.25-5.35 GHz, 5.47-5.725 GHz and
5.725–5.850 GHz band when associated with an access point (AP).
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
RF Radiation Exposure Statement
For body contact during operation, this device has been tested and meets FCC
RF exposure guidelines when used with an accessory that contains no metal
and that positions the handset a minimum of 1.5 cm from the body.
Use of other accessories may not ensure compliance with FCC RF exposure
guidelines.
Canadian Compliance Statement
This Class B Digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte les exigences du Reglement
sur le material broilleur du Canada.
ii
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
European Conformity Statement
unitech Electronics co., Ltd herewith declares that the unitech product is in
compliance with the essential requirements and all other provisions of the
R&TTE 1999/5/EC directive, the EMC 2004/108/EC directive and the Low
Voltage 2006/95/EC directive.
The declaration of conformity is available for download at :
https://portal.unitech.eu/public/Safetyregulatorystatement
RoHS Statement
This device conforms to RoHS ( Restriction Of
Hazardous Substances) European Union regulations
that set maximum concentration limits on hazardous
materials used in electrical and electronic equipment.
Waste electrical and electronic equipment (WEEE)
unitech has set up a policy and process to meet the EU
directive 2002/96/EC and update 2003/108/EC
concerning electronic waste disposal.
For more detailed information of the electronic waste
disposal of the products you have purchased from
unitech directly or via unitech’s resellers, you shall either
contact your local supplier or visit us at :
https://portal.unitech.eu/public/WEEE
iii
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Taiwan NCC Warning Statement
交通部電信總局低功率電波輻射性電機管理辦法
第十二條:經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者
均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條:低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有
干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備
之干擾。
注意事項:
1. 使用過度恐傷害視力。
2. 使用30分鐘請休息10分鐘;2歲以下幼兒不看螢幕,2歲以上每天看螢幕不要超過
1小時。
iv
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Laser Information
The unitech product is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 825-1.
Class II and Class 2 products are not considered to be hazardous. The unitech
product contains internally a Visible Laser Diode (VLD) whose emissions do
not exceed the maximum limits as set forth in the above regulations. The
scanner is designed so that there is no human access to harmful laser light
during normal operation, user maintenance or prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the unitech
product’s optional laser scanner module is located on the memory
compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components.
CAUTION! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser
light. Use of optical instruments with the scanner, including
binoculars, microscopes, and magnifying glasses, with will
increase eye damage. This does not include eyeglasses worn by
the user.
LED Information
The unitech product contains LED indicator(s) or LED ring whose luminance is
not harmful to human eyes during normal operation, user maintenance or
prescribed service operations.
*LED information only applies to the products with LED components.
v
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Battery Notice
1.
To guarantee optimal performance, it is recommended that rechargeable
batteries be replaced every year, or after 500 charging cycles are
completed. It is normal for the battery to balloon or expand after one year
or 500 cycles. Although it does not cause damage, it cannot be used again
and must be disposed of according to the location's safe battery disposal
procedures.
2.
If a battery performance decreases more than 20%, the battery is at the
end of its life cycle. Stop use and ensure the battery is disposed of
properly.
3.
The length of time that a battery lasts depends on the battery type and
how the device is used. Conserve the battery life by doing the following:
 Avoid fully uncharging the battery because this places additional
4.
5.
6.
7.
strain on it. Several partial uncharges with frequent charges are better
than a fully uncharged battery. Charging a partially charged battery
does not cause harm to the unit.
 Keep the battery cool. Avoid hot vehicles. For prolonged
storage, keep the battery at a 40% charge level.
 Do not leave the battery uncharged and unused for an extended
period of time, the battery will wear out and the longevity of the
battery will be at least half of one with frequent charges.
Protect battery life by not over or under charging the battery.
Please do not leave battery unused for long time without charging it.
Despite unitech’s safety precautions, the battery pack may begin to
change shape. If so, stop using it immediately. Please check to see if you
are using a proper power adapter to charge the battery or contact your
service provider for service.
If you cannot charge the battery after it has been idle for an extended
period of time and it begins to heat up, please do not try to charge it. It
may not be functional anymore.
Please only use the original battery from unitech. Using a third party
battery can damage our products. Please note that when such damage
occurs, it is not covered by your warranty.
vi
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
CAUTION!



RISK OF EXPLOSION IF BATTERY IS
REPLACED INCORRECTLY.
DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
如果更換不正確之電池行事會有爆炸的風險
請依製造商說明書處理用過之電池
如果更换不正确之电池行事会有爆炸的风险
请依制造商说明书处理用过之电池
Battery charge notice
It is important to consider temperature when the battery pack is charging.
Charging is most efficient at normal room temperature or in a slightly cooler
environment. It is essential that batteries are charged within the stated range of
0°C to 40°C. Charging batteries outside of the specified range could damage
the batteries and shorten their life cycle.
CAUTION! Do not charge batteries at a temperature lower than 0°C. This will
and make the batteries unstable and dangerous. Please use a
battery temperature detecting device for a charger to ensure a
safe charging temperature range.
Storage and safety notice
Although charged batteries may be left unused for several months, their
capacity may be depleted due to build up of internal resistance. If this happens,
they will require recharging prior to use. Batteries may be stored at
temperatures between -20°C to 60°C, however they may deplete more rapidly
at higher temperatures. It is recommended to store batteries at room
temperature.
* The message above only applies to the usage of the removable batteries.
For the products with non-removable batteries / without batteries, please refer to
the specification of each product.
Product Operation and Storage Notice
The unitech product has applicable operation and storage temperature
conditions. Please follow the limitation of suggested temperature conditions to
avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each
product.
vii
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Adapter Notice
1.
2.
3.
4.
Please do not leave the power adapter in the socket when it is not
connected to your unitech product for charging.
Please remove the power adapter when the battery is fully recharged.
The bundled power adapter that comes with your unitech product is not
meant to be used outdoors. An adapter exposed to water or rain, or a very
humid environment can cause damage to both the adapter and the
product.
Please only use the bundled power adapter or same specification of
adapter to charge your unitech product. Using the wrong power adapter
can damage your unitech product.
* The message above only applies to the product connected to the adapter.
For the products without using the adapters, please refer to the specification of
each product.
Hearing Damage Warning
Zx.3 Warning
The warning shall be placed on the equipment, or on the packaging, or in the instruction
manual and shall consist of the following:
- the symbol of Figure 1 with a minimum height of 5 mm; and
- the following wording, or similar :
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Alternatively, the entire warning may be given through the equipment display during use, when
the user is asked to acknowledge activation of the higher level.
viii
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Worldwide Support
unitech’s professional support team is available to quickly answer questions or
assist with technical-related issues. Should an equipment problem occur,
please contact the nearest unitech regional service representative.
For complete contact information please visit the Web sites listed below:
Taipei, Taiwan – Headquarters
Europe
Tel:
+886-2-89121122
Tel:
+31-13-4609292
E-mail:
info@hq.ute.com
E-mail:
info@eu.ute.com
Address:
5F, No. 136, Lane 235, Baoqiao Road, Xindian
Address:
the Netherlands
District, New Taipei City 231, Taiwan (R.O.C.)
Website:
Website:
http://www.ute.com
China
Kapitein Hatterasstraat 19, 5015 BB, Tilburg,
http://eu.ute.com
Japan
Tel:
E-mail:
Address:
+86-59-2310-9966
info@cn.ute.com
Room401C, 4F, RIHUA International Mansion,
Tel:
+81-3-35232766
E-mail:
info@jp.ute.com
Address:
Xinfeng 3nd Road, Huoju Hi-tech District,
Xiamen, Fujan , China
Website:
E-mail:
Shinkawa, Chuo-Ku, Tokyo, 104-0033, Japan
Website:
Latin America
+886-2-27911556
Tel:
+52-55-5171-0528
info@apac.ute.com
E-mail:
info@latin.ute.com
info@india.ute.com
Address:
info@mideast.ute.com
Address:
http://jp.ute.com
http://cn.ute.com
Asia & Pacific / Middle East
Tel:
Kayabacho Nagaoka Building 8F.,1-5-19
17171 Park Row, Suite 210
Houston, TX 77084USA (Rep.)
4F., No. 236, ShinHu 2nd Rd.,
Website:
http://latin.ute.com
NeiHu Chiu, 114, Taipei,Taiwan
Website:
http://apac.ute.com / http://mideast.ute.com
North America
Tel:
E-mail:
+1-714-8916400
info@us.ute.com / info@can.ute.com
Address:
6182 Katella Ave, Cypress, CA 90630, USA
Website:
http://us.ute.com / http://can.ute.com
ix
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Warranty Policy
The items covered under the unitech Limited Warranty are free from defects
during normal use.
The warranty period is varied from each country. Please consult with your
supplier or unitech local office for actual length of warranty period to your
purchased product.
Warranty becomes void if equipment is modified, improperly installed or used,
damaged by accident or neglect, or if any parts are improperly installed or
replaced by the user.
x
© 2015 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co., Ltd.
Table of content
Preface………………………………………………………………………………i
Table of content............................................................................................. xi
1. Package Contents......................................................................................1
2. Getting started ...........................................................................................2
2.1 Device overview ...................................................................................2
2.2 Assembly ..............................................................................................4
Accessing battery, Micro SD card and SIM card.....................................4
Put battery back to PA700 ......................................................................5
2.3 Charging the battery .............................................................................6
2.4 Data Communicating with PC Device...................................................7
2.5 LED status............................................................................................7
2.6 To check the battery level and to access the battery usage menu .......8
3. Basic Operation .......................................................................................10
3.1 Accessing and using applications.......................................................10
To open the Application screen .............................................................10
To browse the Application screen .........................................................10
To create a shortcut to an application on the Home screen ..................10
To Remove a shortcut of an application on the Home screen...............10
Calling ......................................................................................................10
Call handling .........................................................................................10
To make a call by dialing.......................................................................10
To end a call .........................................................................................10
3.2 Barcode Scanning (For Imager Version only)..................................... 11
3.3 RFID Sensing .....................................................................................12
3.4 MoboLink App Setting ........................................................................13
4. Specification.............................................................................................15
Camera and Flash Light .......................................................................15
xi
1. Package Contents
PA700
USB cable
(Standard USB to Micro USB)
Charger
Battery
Power Plug Adapter
Hand Strap
1
2. Getting started
unitech PA700 is an Android platform device. Android platform device has
great flexibility that allows you to make customized configurations and
enhancements by install and remove Apps.
With Android operation system, your device has limitless possibilities to update
to latest features and improvements.
2.1 Device overview
1. Receiver
7. Back button
2. LED indicator
8. Flash LED
3. Search button
9. 5M Camera with AF
4. Microphone.
10. Reset button
5. Menu button
11. NFC
6. Home screen button
12. Mounting screw for battery cover
13. Speaker
2
13. Bar Code Scan Engine
15. Volume Down Button
14. Scan Button
16. Volume Up Button
17. Micro USB port
19. Power button
18.Earphone jack
20. Scan button
3
2.2 Assembly
Accessing battery, Micro SD card and SIM card
1. Using a proper tool (ex. a coin) to loosen the two screws on the battery
cover by turning counterclockwise.
2. Remove the back cover and pull the battery out.
3. Now you can access the micro SD card slot and SIM card slot.
1. Micro SD card slot
2. SIM card slot
4
Put battery back to PA700
1. Using a proper tool (ex. a coin) to loosen the two screws on the battery
cover by turning counterclockwise.
2. Put battery into battery compartment and put back cover .
3. Using a proper tool (ex. a coin) to tighten the two screws on the battery
cover by turning clockwise.
5
2.3 Charging the battery
Connect PA700 to the charger, it will be charged automatically.
1. Connect the standard USB connector to the charger.
2. Connect the micro USB connector to the micro USB port at the bottom.
3. Plug the AC charger into a wall outlet. If needed, attach a plug converter
onto the AC charger.
6
2.4 Data Communicating with PC Device
1. Connect the standard USB connector to the USB port of the PC device.
2. Connect the micro USB connector to the micro USB port at the bottom.
2.5 LED status
Green
■ The battery is fully charged
Red
■ The battery is charging.
■ The battery level is between low and full.
Blinks Red
■ Using power adapter without the battery in the unit.
Blue
■ Message is received.
7
2.6 To check the battery level and to access the battery usage
menu
1 From your Home screen, tap
.
2 Find and tap Settings.
8
3 Find and tap
Battery.
9
3. Basic Operation
3.1 Accessing and using applications
To open the Application screen
From your Home screen, tap
.
To browse the Application screen
From the Application screen, flick right or left.
To create a shortcut to an application on the Home screen
1 From your Home screen, tap
.
2 Touch and hold an application icon and then the Home screen opens.
3 Drag the icon to the desired page on the Home screen by flicking left or rught,
then release your finger.
To Remove a shortcut of an application on the Home screen
1 From your Home screen, touch and hold the icon of the desired application
you want to remove
2 “X Remove” shows on the top of the home screen.
3 Drag the icon to be removed to the “X Remove”.
Calling (For Phone Version only)
Call handling
To make a call by dialing
1 From your Home screen, tap
.
2 Find and tap Phone.
3 Enter the number of the recipient and tap Call. To delete a number, tap
To end a call
• Tap
.
10
.
3.2 Barcode Scanning (For Imager Version only)
1. Tap the ScanService
.
2. Aim the Bar code Scan Engine to the barcode and press one of two scan
buttons.
11
3.3 RFID Sensing
1. Tap the ScanService
.
2. Place NFC reader near the tag to read the information.
12
3.4 MoboLink App Setting
MoboLink is a software platform that helps unitech customers to remote
manage their purchased devices and applications. The core of the MoboLink
platform provides functionalities in the MDM (Mobile Device Management) and
MAM (Mobile Application Management) domains, and then further extends into
other management functions such as alert notification management and
account management.
To enable MoboLink app, please follow the instructions as below :
1. Tap
to enable MoboLink app :
2. MoboLink app setting is as below :
Step 1 : Enter MoboLink server URL
manually in the text field or scan a
MoboLink server URL Barcode.
Step 2 : Tap “Save” to initiate MoboLink app
13
3. MoboLink app screen information is as below:
To switch on/ off MoboLink app, slide On/Off
button. Then tap “Exit” to leave the screen.
Note: If this app is on, it will jump out on the
screen when the device is offline.
Please visit the support page to know more
about MoboLink.
Note: For detailed operation, solution and usage,
please refer to MoboLink user’s guide.
14
4. Specification
System Features
CPU
TI OMAP 4470 1.5Ghz Dual Core Processor
Memory
1GB Mobile DDR RAM
8GB eMMC Flash
OS
Android 4.3 Jelly Bean
Languages support
English, Simp. Chinese, Traditional Chinese, Japanese,
Spanish, German, French and multiple languages
Display
Gorilla Glass II with 5-point capacitive touch panel
4.7" Color 450nits High Brightness TFT 720x1280 dots IPS LCD
Keypad
4 x Function key
1 x Power key
2 x Scan Key
2 x Volume key
Indicator
1 LED indicate charge/Message
Vibrator
Engines
1D CCD Barcode scanner
SE655:
Illumination/AIMER : LED 630 ± 30 nm
Optical Resolution : 5 mil (minimum readable bar code
module size)
Scan Repetition Rate : Nominally 50 scans/second
Print Contrast : 20% (minimum print contrast)
Ambient Light Immunity Light Source: 4845(lux) ± 5%
2D Imager
SE4500:
Sensor Resolution: 752 x 480 pixels
Field of View: Horizontal: 40°, Vertical: 25°
Aiming LED (VLD): 655 ±10 nm Laser
Illumination Element: 625 ±5 nm LEDs (2x)
Min. Print Contrast: Minimum 25% absolute dark/light
reflectance measured at 650 nm
Ambient Light: Max 96,900 lux (direct sunlight)
Symbologies
1D CCD Barcode scanner
All major codes
15
2D Imager
PDF417
(2D is only available when the 2D imager MicroPDF417
is on your device )
Code 128 Emulation
Data Matrix
Data Matrix Inverse
Decode Mirror Images (Data Matrix Only)
Maxicode
QR Code
QR Inverse
MicroQR
Aztec
Aztec Inverse
Audio
1W speaker 85 dB at 10cm , 3.5mm Audio Jack, Receiver, Microphone
Regulatory Approvals
CE, NCC, FCC, BSMI, VCCI, CCC, RoHS compliance
Communication
Camera and Flash Light
5MP CMOS Sensor Camera with dual Auto focus LED
flash light
External storage
Support MicroSD memory card up to 32GB
USB
USB 2.0 OTG
WLAN
IIEEE 802.11 b/g/n
Bluetooth
Bluetooth 4.0
WWAN
GSM/GPRS/EDGE 850/900/1800/1900 MHzUMTS
850/900/1700/1900/2100 MHz WCDMA modem, HSPA+,
DL: 21Mbps/ UL: 5.76Mbps
Other Sensors
GPS
eCompass
Light & Proximity sensor
G-sensor
RFID/HF (Optional)
Frequency: 13.56MHz
Tag Support: ISO15693, ISO14443A , ISO14443B
Support NFC
GPS
12 x 12 mm patch antenna
Power Source
Main Battery
11.9Wh 3.7V @3220mAh Li-ion battery pack
16
Backup Battery capacity
1 hour
Enclosure
Weight
285g (with battery)
Dimension
160mm x17.4mm x 80mm ( without engine )
Environmental
Operating temperature
14°F to 122°F (-10°C to 50°C)
Storage temperature
-4°F to 140°F (-20°C to 60°C)
Charging Temperature
32°F to 104°F (0°C to 40°C)
Relative Humidity
5% ~ 95% ( non-condensing )
Drop test to Concrete
1.2 meter
Environmental Sealing
IP65
Vibration and Shock test
MIL-STD-810F, 514.4 process II
Software
Android 4.3 API level 18
Accessories
Single Slot USB Client/on the go Cradle with Single Slot Battery Charger
Handstrap
3220mAH standard Battery
USB Communication Cable
Power adaptor with universal plugs
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising