Fanimation FP810AM Air Shadow - Owners Manual

Fanimation FP810AM Air Shadow - Owners Manual
The Air Shadow
™
Glass Bowl Ceiling Fan
WARNING: Support Directly From Building Structure
Net Weight 17.24 kg (38 lbs)
Model No. FP810**
OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
For Canada, this fan must be secured directly to the building structure or ceiling joist.
Don’t secure this fan to an outlet box.
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. (fan and accessories not to exceed 50 lbs.
or 22.7 kgs.). See page 4 of owner’s manual for support requirements. Consult a qualified electrician if in doubt.
WARNING: Mount only to an outlet box marked acceptable for fan support.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
knowledge or experience, have your fan installed by licensed electrician.
6. Suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with Fan Speed Control Part No. UC7067RC,
manufactured by Rhine Electronic Co., Ltd.
WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL CONTROL/SWITCH.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation Fan
1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during
the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to
defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser
will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we
will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,
tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of
heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan
or Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid
damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation
will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,
except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary
from state to state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
Table of Contents
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
How to Hang Your Ceiling Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
How to Wire Your Ceiling Fan - C28 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
How to Operate Your C28 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Canopy Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Blade Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Trouble Shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the LK810 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
This Manual is Designed to Make it as Easy as Possible for You
to Assemble, Install, Operate, and Maintain Your Ceiling Fan
Tools Needed for Assembly
• One Phillips head screwdriver
• One stepladder
• One ¼˝ blade screwdriver
Materials
• One wire stripper
• Three wire connectors
(supplied)
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3conductor (2-wire with ground) of the following size:
▲WARNING
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 4). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.
Installed Wire Length
Wire Size A.W.G.
Up to 50 ft.
50 - 100 ft.
14
12
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.
Unpacking Instructions
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in finding your place should you be interrupted.
▲WARNING
• Fan Motor assembly
• Hardware bags:
– Support Safety Cable bag – Two 5/32˝ threaded rods
• Light Kit / Parts assembly
– Two 5/32˝ lockwashers
• Internal Housing
– Two knurled knobs
• Adapter Switch Cup
– Three 3/16˝ screws
• Glass Bowl
– Three 3/16˝ lockwashers
• Hanger Bracket
– Seven wire nuts
• Downrod/Hanger Ball
– Phillips screwdriver, 4˝
assembly
– Rubber Washer
• Ceiling Canopy
– Finial nut
• Motor Coupling Cover
– Six 5/32˝ screws
• C28 Remote Control
– Three 5/32˝ lockwashers
• Receiver Unit
– Two wire nuts
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 13)
Hanger Bracket
Downrod/
Hanger Ball
Assembly
Ceiling Canopy
Motor
Coupling
Cover
Receiver Unit
C28 Remote
Control
Switch Cup
Light Kit
Adapter
Switch Cup
Glass Bowl
(AM-Amber Glass or PT-Parrot, shown)
Finial Nut
Fan Motor Assembly
Internal Housing
3
Hardware Bag
Electrical and Structural Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit. The
outlet box must be securely anchored and capable of
withstanding a load of at least 22.7 kgs (50 lbs). Figure 1
depicts different structural configurations that may be used
for mounting the outlet box.
Ceiling
▲WARNING
Ceiling
Joists
To reduce the risk of fire, electrical shock, or personal
injury, mount fan to outlet box marked acceptable
for fan support of 22.7 kg (50 lbs) or less. Use screws
supplied with outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for
fan support and may need to be replaced. Consult a
qualified electrician if in doubt.
2˝ x 4˝
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and remove
the existing light fixture.
Outlet
Box
Figure 1
▲WARNING
▲WARNING
Turning off wall switch is not sufficent. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and the
ceiling fan must be properly grounded as a precaution
against possible electrical shock.
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
How to Assemble Your Ceiling Fan
1. Prior to assembly, set aside and save the hardware
bag(s) packed in the packing.
2. Remove the Hanger Ball by loosening the setscrew
in the Hanger Ball until the ball falls freely down the
Downrod. (Figure 1) Remove the Pin from the Downrod,
then remove the Hanger Ball. Retain the Pin and Hanger
Ball for reinstallation in Step 8.
Pin
Hanger
Ball
Setscrew
3. The fan comes with blue, black, gray and white 80˝
wires. Separate and untwist the wires. Route the wires
through the Downrod.
NOTE: You will be using either the 6˝ downrod supplied with
your fan or an optional downrod purchased seperately.
Figure 1
4. Position Fan/Motor Assembly on styrofoam pedestal, for
ease of assembly.
Motor
Coupling
Cover
Downrod
Support
5. Loosen the two setscrews in the Downrod Support. Align
the Clevis Pin holes in the Downrod with the holes in the
Downrod Support. Install the Clevis Pin and secure with
the Hairpin Clip. (Figure 2) Be sure to push the straight
leg of the hairpin clip through the hole near the end of the
clevis pin until the curved portion of the hairpin clip snaps
around the clevis pin. The hairpin clip must be properly
installed to prevent the clevis pin from working loose. Pull
on the Downrod to make sure the clevis pin is properly
installed. (Figure 2)
Hairpin Clip
Clevis Pin
Setscrew (2)
Figure 2
4
How to Assemble Your Ceiling Fan (cont’d)
6. Route wires through opening in Motor Coupling Cover.
Position Motor Coupling Cover on fan shown with open
side facing down. (Figure 2)
7. Route wires through opening in Canopy. Position
Canopy on fan shown with open side facing up. (Figure 3)
8. Reinstall the Hanger Ball (Figure 3) on the Downrod
as follows. Route the three 80˝ wires through the Hanger
Ball. Position the Pin through the two holes in the Downrod
and align the Hanger Ball so the Pin is captured in the
groove in the top of the Hanger Ball. Pull the Hanger Ball
up tight against the pin. Securely tighten the setscrew
in the Hanger Ball. A loose setscrew could create fan
wobble.
Downrod/Hanger
Ball Assembly
Ceiling
Canopy
Motor
Coupling
Cover
▲WARNING
It is critical that the clevis pin in the downrod support
is properly installed and the setscrews are securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
9. While pulling up on the hanger ball, securely tighten
the two 3/16-24 x 3/8˝ setscrews in the downrod support.
(Figure 2)
NOTE: The setscrews must be properly installed as
described above, or fan-wobble could result.
10. Slide the Motor Coupling Cover down until it touches
the top of the Housing. (Figure 3)
11. The fan comes with blue, black, gray and white leads.
Before installing fan, measure up approximately 6-9 inches
above top of Downrod/Hanger Ball Assembly. Cut off
excess wire and strip back insulation ½˝ from end of wire.
12. You have now completed the assembly of your new
ceiling fan. You can now proceed with the hanging and the
electrical wiring of your fan.
5
Figure 3
How to Hang Your Ceiling Fan
▲WARNING
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before hanging.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
▲WARNING
The fan must be hung with at least 7´ of clearance from
floor to blades (Figure 1)
No
less than
7 ft
▲WARNING
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs. Hanger bracket
must seat firmly against outlet box. If the outlet box is
recessed, remove wallboard until bracket contacts box.
If bracket and/or outlet box are not securely attached,
the fan could wobble or fall.
Figure 1
1. Using the 3⁄8˝ x 2˝ lag bolt and flat washer, attach
safety cable to ceiling joist or wood structural member.
The lag bolt will pass through the flat washer, safety
cable loop, the junction box and into the building structure
(Figure 2). You will first drill a ¼˝ pilot hole into the
building structure to prevent splitting or cracking.
Wood Member
(2˝ x 4˝ Approx.)
Floor
Ceiling Joist
2. Securely attach the hanger bracket to ceiling junction
box acceptable for ceiling support.
NOTE: Ceiling support cable cannot be secured to
junction box only, it must be directly secured to ceiling
joist or structural member using the ⅜˝ x 2˝ lag bolt and
flat washer. (Figure 2).
Junction
Box
Ceiling
Ceiling
Support
Cable
3. Make sure the electrical supply wires, including the
hanger bracket grounding wire and safety cable are
pulled through the downrod, between the hanger bracket
and the junction box so that electrical connections can be
made later.
Hanger Bracket
Figure 2
4. Carefully lift the fan and seat the downrod/hanger ball
assembly on the hanger bracket that was just attached to
the ceiling joist. Be sure the groove in the ball is lined up
with tab on the hanger bracket. (Figure 3)
5. Attach the safety cable to ceiling support cable. Slide
cable clamp onto safety cable (from fan). Place the end
of cable through the loop of ceiling support cable. Pull as
much cable through loop as possible. Feed end of cable
into clamp hole and firmly tighten screw (Figure 3). Cut
off excess safety cable.
Attach
Safety Cable to
Ceiling Support
Cable
▲WARNING
Tab
NOTE: Supply wires and
fan wires omitted for clarity
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
▲WARNING
To avoid possible shock, do not pinch wires between the
downrod/hanger ball assembly and the hanger bracket.
6
Downrod/Hanger
Ball Assembly
Figure 3
How to Wire Your Ceiling Fan - C28 Remote Control
If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a
licensed electrician.
▲WARNING
Remote Transmitter
Unit Detail
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
Reciever Unit Detail
9V
Battery
1. Setting the Code: The remote unit has 16 different
code combinations. It may be necessary to test a couple
frequency code settings to improve signal reception
and/or eliminate interference from other remote control
household items. Multiple fans should have different code
settings to allow independent fan control. To set the code,
perform these steps.
• Transmitter: remove battery cover. Press firmly below
arrow and slide battery cover off. Slide code switches to
your choice of up or down position. Factory setting is all
up. Do not use this position. With a small screwdriver or
ball point pen slide firmly up or down (Figure 1a). Replace
battery cover on the transmitter.
• Receiver: Slide code switches to the same positions
as set on your transmitter (Figure 1b).
Figure 1a
Figure 1b
NOTE: If fan or supply wires are different colors
than indicated, have this unit installed by a qualified
electrician.
Ceiling
Bracket
(Open End)
Receiver Unit
NOTE: Receiver wires omitted for clarity.
Figure 2
2. Installing Receiver in Hanger Bracket:
• Slide remote Receiver into the Hanger Bracket
(Figure 2).
• Connect wires as indicated: (Figure 3)
• Green Hanger Bracket & Hanger Ball wires to BARE
(ground) wire.
• BLACK Receiver Unit wire (AC IN L) to BLACK supply
wire.
• WHITE Receiver Unit wire (AC IN N). to WHITE supply
wire.
• WHITE Receiver Unit wire (TO MOTOR N) to WHITE
fan wire.
• BLACK Receiver Unit wire (TO MOTOR L) to BLACK
fan wire.
• BLUE Receiver Unit wire (FOR LIGHT DOWN) to BLUE
light wire.
• GRAY Receiver Unit wire (REVERSE MODULE) to
GRAY wire.
• Position all connected wires and receiver antenna to
allow installation of ceiling canopy.
• Using canopy screws threaded into the hanger bracket
install ceiling canopy. (see page 8)
GRN from hanger ball
GRN from bracket
GRN or BARE GROUND
WH-TO MOTOR N
BLK-TO MOTOR L
GRAY-REVERSE MODULE
BLUE-FOR LIGHT DOWN
WH-AC IN N
BL-AC IN L
BLK-ANT
120 VAC SUPPLY
(User Supplied)
Figure 3
▲WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until the blades is in place. Noise and fan damage
could result.
3. After making the wire connections, the wires should
be spread apart, turned upward and pushed carefully up
into the outlet box, with the grounded conductor and the
equipment-grounding conductor on one side of the outlet
box and the ungrounded conductor on the other side of the
outlet box.
7
How to Operate Your C28 Remote Control
1. Operating & Using Remote Transmitter (Figure 1):
Install 9 volt battery (If not using for long periods of time,
remove battery to prevent damage to transmitter). Store
the transmitter away from excess heat or humidity.
• HI Push Button – high fan speed
• MED Push Button – medium fan speed
• LOW Push Button – low fan speed
• OFF Push Button – fan off
• REV Push Button – toggles between air upflow and
air downflow
• *Demo Push Button – on/off auto demo mode
• Light Push Button – on/off and brightness control for
optional down light.
To control either light hold down key to increase or
decrease brightness. Tap key quickly to turn light on or
off. The light keys have auto resume and will stay at the
same brightness as the last time it was turned off.
Figure 1
*Demo mode is initiated by pressing the Demo button
on the remote, lights will flash 3 times. Fan runs for 2½
minutes then shuts off for ½ minute. The 2 ½ / ½ minute
run cycles continue until any other button is pressed on
the remote control.
Installing the Canopy Housing
NOTE: This step is applicable after the neccessary wiring
is completed. (see page 7)
▲WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy housing
and not pinched between the housing and the ceiling.
1. Screw in two threaded rods into the Hanger Bracket
(Figure 1a).
NOTE: The threaded rods in the hanger bracket serve as
guides for easier installation.
NOTE: Supply wires and fan wires omitted for clarity.
Figure 1a
Figure 1b
2. Securely attach the Canopy Housing to the Hanger
Bracket using the external lockwashers and knurled knobs
supplied with your fan (Figure 1b).
Maintenance
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should be
avoided to prevent damage to finish.
CAUTION
Do not use water when cleaning your ceiling fan. It could
damage the motor or the finish and create the possibility
of electrical shock.
Blade Cleaning
Avoid using water, cleansers, or harsh rags, which can
warp and ruin the blade and the finish.
Periodic light dusting of the blades is recommended.
A feather duster will work best.
8
Trouble Shooting
▲WARNING
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
Trouble
1. FAN WILL NOT START
Probable Cause
Suggested Remedy
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
2. Check line wire connections to fan and switch wire
connections in the switch housings.
CAUTION: Make sure main power is turned off !
3. Dead battery in remote control.
3. Replace with fresh battery.
1. Loose screws in motor housing.
1. Check to make sure all screws in motor housing are
snug (not over-tight).
2. Wire connectors inside housing rattling.
2. Check to make sure wire connectors in switch
housing are not rattling against each other or against
the interior wall of the switch housing.
CAUTION: Make sure main power is turned off !
2. FAN SOUNDS NOISY
3. FAN WOBBLES
EXCESSIVELY
3. Motor noise caused by solid state variable speed
control.
3. Some fan motors are sensitive to signals from
solid-state variable speed controls. Solid-state controls
are not recommended, choose an alternative control
method.
4. Screws holding blades to blade holders are loose.
4. Tighten screws securely.
5. Lower housing support set screw loose.
5. Tighten set screw securely.
1. Setscrew in downrod support is loose.
1. Tighten both setscrews securely in downrod support.
2. Setscrew in downrod/hanger ball assembly is loose.
2. Tighten the setscrew in the downrod/hanger ball
assembly.
3. Screws securing fan blade holders to motor hub are
loose.
3. Check to be sure screws which attach the fan blade
holders to the flywheel are tight.
4. Hanger bracket and/or ceiling outlet box is not
securely fastened.
4. Tighten the hanger bracket screws to the outlet box,
and secure outlet box.
1. If possible, consider using a longer downrod. For
example, use a 12” downrod instead of the 6” downrod
that comes with your fan.
4. NOT ENOUGH AIR
MOVEMENT
9
Installing the LK810**
CAUTION
▲WARNING
Turning off wall switch is not sufficent. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and the
ceiling fan must be properly grounded as a precaution
against possible electrical shock.
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
Figure 1
Figure 2
1. Locate accessory mounting plate on bottom of fan.
2. Mount internal housing unit on accessory mounting
plate with 3 screws and 3 lockwashers provided, in bag
labeled “Housing to Motor Assembly”.
Figure 3
Figure 4
3. Install switch cup adapter on the internal housing unit
with 3 screws and 3 lockwashers provided.
4. Locate white and blue wires labeled “FOR LIGHT”.
Connect white-to-white and blue-to-black wires with wire
nuts supplied.
10
Installing the LK810** (cont’d)
Figure 5
Figure 6
5. Install light fixture to adapter with 3 screws provided.
6. Install five-60 watt candelabra bulbs (not included).
Figure 7
INSTALLATION NOTE
HEAVY! Requires 2 people to hang the glass bowl.
7. Assemble and install glass bowl with rubber washer,
and finial nut, do not over-tighten.
11
Parts List
Model #FP810**
Ref. #
Description
Part #
FP810¾¾
Retractable Fan Assembly – Glass Bowl
FAN MOTOR ASSEMBLY — MAR20CY
5
Retractable Fan Motor Assembly
10
Control Receiver
RECCAN57DEMO
Remote Control
C28
11
—
Support Cable Bag Containing:
Ceiling Support Cable
Cable Clamp
Flat Washer
Lag Bolt, 3/8˝ x 2˝
GLASS BOWL LIGHT KIT ASSEMBLY — LK810**
6
Internal Housing
7
Adapter Switch Cup
8
Switch Cup Light Assembly
AP81056WH
1
Hanger Bracket Assembly
APG610BL
2
Ball/Downrod Assembly
ADR1x6¾¾
3
Ceiling Canopy
PG165¾¾
4
Motor Coupling Cover
P81090¾¾
9
P81070WH
P81085BL
Glass Bowl, (PT-Parrot, shown) or (AM-Amber Glass)
—
Hardware Bag(s) Containing:
Rubber Washer
Wire Nut (7)
Finial Nut
Canopy Hardware Bag Containing:
8
5/32˝
Threaded Rods (2)
5/32˝
External Lockwasher (2)
Knurled Knobs (2)
HDWLK810¾¾
Housing Mount Hardware Bag Containing:
3/16˝
Pan Head Screw (3)
3/16˝
External Lockwasher (3)
Phillips Screwdriver, 4˝
Adapter Mounting Hardware Bag Containing:
5/32˝
Pan Head Screw (6)
5/32˝
External Lockwasher (3)
Wire Nut (2)
¾¾
Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging materials, be certain all parts have been removed
How To Order Parts
Contact your retail store for repair parts.
When ordering repair parts, always
give the following information.
12
• Part Number
• Part Description
• Fan Model Number
The Air Shadow Fan FP810**
Exploded-View
1
6
2
7
8
3
9
4
5
8 ref
11
10
8
Figure 1
NOTE: The illustration shown is not to scale or its actual configuration may vary
13
Copyright 2007 Fanimation
10983 Bennett Parkway
Zionsville, IN 46077
(888) 567-2055
FAX (866) 482-5215
Outside U.S. call (317) 733-4113
Visit Our Website www.fanimation.com
2007/01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising