© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved

© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Version 11/14
WARNINGS AND NOTICES
NOTICE

This game is intended to be operated for amusement purposes only. It is not to be operated in violation of any federal, state, or local laws or
regulations. As the owner and/or operator of this game you are responsible for its operation in compliance with such laws and regulations. The
factory settings for this game may require adjustment in order to comply with the laws and/or regulations in the jurisdiction where the game is
located. It is the sole responsibility of the operator to determine what laws and/or regulations are applicable and to make any adjustments to the
game before operating it for its intended purpose.

This manual and the information contained within is subject to change without notice.

The Showpiece cabinet is intended for use with the Showpiece Integrated Stand (Model 304S).
WARNING

Use of unauthorized parts or making any unauthorized modifications will void the warranty and may result in the game operating in an unsafe or
incorrect manner.

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

This cabinet is not suitable for installation in an area where a water jet would be used. The cabinet must not be cleaned by a water jet.
WARRANTY, REPAIR, AND RETURN POLICY

90-day warranty on all electronic components. All warranty periods begin on the date of purchase from Incredible Technologies, Inc.

There is a minimum $75.00 service charge for all non-warranty repairs or returns.

For all servicing, return to Incredible Technologies, Inc.

ANY non-factory repair or attempted repair voids warranty.
RETURN MERCHANDISE AUTHORIZATION

All returned merchandise must have a Return Merchandise Authorization (RMA) number marked clearly on the outside of the package.

You must obtain all RMA numbers from Incredible Technologies. Please have the product's Cabinet Identification Device (CID) number available
when calling for an RMA number.

Merchandise returned without an RMA number will not be accepted.

Warranty may be void if serial number or security labels are tampered with or removed. Opening the Nighthawk Chassis system will void your
warranty.

Advance replacement hardware will be shipped to the customer address on file unless specified otherwise.

Advance replacement hardware will be billed to the customer until Incredible Technologies, Inc. receives the returned merchandise, at which time a
credit will be issued.

All repairs and/or replacements will ship as soon as possible after receipt or request (subject to availability).
PAYMENT FOR AND STORAGE OF REPAIR MATERIALS

Materials sent to IT for repair must be paid for according to current price schedules and in a reasonable time. Storage fees for repaired equipment
will be charged at a rate of $50.00 (Fifty US Dollars) per calendar month or fraction thereof after 90 (Ninety) days from notice to the customer that
the repairs are complete. IT reserves the right to resell repaired equipment to cover accumulated storage charges when the accumulated storage
charge reaches 100% (One Hundred Percent) of the repaired items’ then-current replacement cost.
- INCREDIBLE TECHNOLOGIES, INC
GOLDEN TEE® GOLF, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc. All
Rights Reserved.
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their
respective owners. All rights reserved.
PERPETUAL SOFTWARE LICENSE
Incredible Technologies, Inc. (“IT,”) hereby offers you (“Licensee”) the right to install and use certain copyrighted computer software produced by IT
under the following terms and conditions. This License shall govern the use of the software known as “Golden Tee GOLF 2012” (“Update”) when applied
as an update to pre-existing Golden Tee GOLF-equipped hardware (“GT Cabinets”) equipped with an earlier version of the Golden Tee GOLF software
(“Prior Version.”)
1) Licensing Fee
The Licensing Fee (“LF”) shall be as follows:

US$0.00 (Zero United States Dollars and zero cents.)
2) Term
The License shall be valid on the first date that both the LF is paid for the Update and it is installed on a GT Cabinet. If the Update has been offered or
sold to you under the terms of a Term Software License, the terms of this License shall become applicable if and when the Term Software License
terminates in favor of this Perpetual Software License, as set forth in the Term Software License. The term shall be perpetual and throughout the
Universe for the Update on the GT Cabinet upon which it is installed at the time the LF is paid. Updates are not transferrable to any other GT Cabinet,
for any reason. If a GT Cabinet with an Update is destroyed or otherwise taken out of operation, this License shall terminate.
3) License Rights
Licensee shall have the right to utilize the Update on authorized GT Cabinets in the normal course of business and as controlled by the Rules of ITNet,
as set forth in a separate “Operator Agreement” document, the terms and conditions of which, where not conflicting with the terms and conditions herein,
are hereby incorporated by reference. Updates may only be operated on GT Cabinets which are installed in commercial locations, as that term is defined
by IT, and to which there is general access by all parties with a general right to enter the location where the GT Cabinet is operated.
4) Legal Operation
Updates include various features which may not be lawful to operate in any given jurisdiction. No provision of any feature, or its licensure to Licensee
under the terms herein shall be deemed as advice that operation of that feature is lawful or not lawful in any given jurisdiction. Licensee shall make
reasonable efforts to disable any user-adjustable feature which they know or should have known as not lawful to operate in the location where a GT
Cabinet with an Update is being operated.
5) Termination and Rollback
In the event that this License is terminated for whatever reason, Licensee shall have absolutely no right to operate any GT Cabinet upon which an
Update has been installed. IT reserves the absolute right, at its sole discretion, to terminate the operation of any GT Cabinet upon which an unlicensed
Update is installed. If Licensee wishes to restore such a GT Cabinet to operating condition without acquiring a new License for the Update, IT will rollback that GT Cabinet, at no charge to the Licensee, to the Prior Version upon return (at Licensee’s expense) of the required hardware to IT’s service
center.
6) Governing Law and Jurisdiction
The validity and construction of this License and of the rights and obligations set forth herein shall be determined and governed by the laws of the State
of Illinois. The parties hereby submit to the Jurisdiction of any state or federal court in Cook County Illinois. Licensees operating outside the borders of
the United States of America, regardless of their citizenship or residency, explicitly agree to allow any assets they may have in the USA or any other
foreign country to be attached, garnished, forfeited or otherwise reached by any legal act if, after due process of law, they are found to be liable to IT for
damages by reason of breach of this License.
7) Warranty
If the Licensee discovers any physical defect in the media (disk, EPROM, flash media, etc.) on which the Update is distributed or in the documentation,
which in the opinion of Incredible Technologies, Inc. (IT) prevents the product from being used as reasonably intended, IT will replace the media or
documentation at no charge. The purchaser must return the item to be replaced, with proof of purchase, to IT within 90 days after taking delivery of the
Update.
8) Disclaimer and Waiver of Remedies
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all implied, statutory, or common-law warranties,
including warranties of merchantability and fitness for a particular purpose, and limits the purchaser's remedy to returning the Update to IT for
replacement.
IT makes no warranty or representation, either express or implied, with respect to Updates, their quality, performance, merchantability, or fitness for a
particular purpose. Updates are licensed "as is," and the Licensee, by installing the Update, assumes the entire risk as to their quality and performance
other than as explicitly set forth herein.
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the Update, even if advised of the possibility of such damages. The warranty and
remedies set forth above are exclusive and in lieu of all others, oral or written, express or implied. No person, seller, dealer, agent, or employee is
authorized to make any modification or addition to this limited warranty.
In jurisdictions which do not allow the exclusion of implied warranties or liability for incidental or consequential damages, acceptance of this License and
installation of the Update includes stipulation that the most minimal requirements of the law of those jurisdictions shall govern any additional required
additional rights of Licensee.
9) Severability
If any provision of this License shall be held by a court of competent jurisdiction to be illegal, invalid or unenforceable, the parties nevertheless agree that
the court should endeavor to give effect to the parties' intentions as reflected in the provision, and the remaining provisions shall remain in full force and
effect.
GOLDEN TEE® GOLF, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc. All
Rights Reserved.
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their
respective owners. All rights reserved.
GOLDEN TEE® GOLF, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc. All
Rights Reserved.
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their
respective owners. All rights reserved.
Golden Tee GOLF 2015 Manual & User Guide
TABLE OF CONTENTS
TABLE OF CONTENTS ......................................................................................................................................... 1 SHOWPIECE CABINET ......................................................................................................................................... 4 Showpiece Cabinet Contents................................................................................................................................. 4 Leg Leveler Adjustment ......................................................................................................................................... 4 Mount Main Screen Display ................................................................................................................................... 4 Install Marquee....................................................................................................................................................... 4 HDTV DIP SWITCH SETTINGS and NIGHTHAWK SYSTEM BOX...................................................................... 5 Video Connections for 720p/1080p HDTV ............................................................................................................. 6 INSTALL SECONDARY MONITOR for Showpiece ............................................................................................... 7 ABOUT THE SECONDARY MONITOR................................................................................................................. 7 Final Check............................................................................................................................................................. 7 Apply Power ........................................................................................................................................................... 7 General Cabinet Maintenance................................................................................................................................ 8 Care and Cleaning of Rubber Bumper .................................................................................................................. 8 Nighthawk Air Filter ................................................................................................................................................ 8 Trackball Maintenance ........................................................................................................................................... 8 Care and Cleaning of Cooling Fans and Vents ..................................................................................................... 8 Showpiece Cabinet Repair Procedures ................................................................................................................. 9 System Chassis Box .............................................................................................................................................. 9 I/O Board ................................................................................................................................................................ 9 Cash Vault............................................................................................................................................................ 10 Control Panel ....................................................................................................................................................... 11 Speakers .............................................................................................................................................................. 12 OFFLINE KIT CONTENTS ................................................................................................................................... 13 Recommended Tools ........................................................................................................................................... 13 Installation Preparation ........................................................................................................................................ 14 Preparing The Cabinet ......................................................................................................................................... 14 Cabinet Selection ................................................................................................................................................. 14 Preparing the Cabinet for Installation................................................................................................................... 14 Check High-Definition Television ......................................................................................................................... 16 Electronics Installation .......................................................................................................................................... 16 Install Nighthawk System box .............................................................................................................................. 16 Install Cabinet Identification Device (CID) ........................................................................................................... 16 Install I/O Board ................................................................................................................................................... 17 Trackball and Button Preparation (For Most Kits) ................................................................................................ 17 Control Panel Overlay Installation........................................................................................................................ 18 Finishing The Control Panel................................................................................................................................. 19 Complete System Box Connections ..................................................................................................................... 20 Attach I/O Power, Audio and USB cables ............................................................................................................ 20 Attach Main Video Cable ..................................................................................................................................... 20 Attach Power Cable ............................................................................................................................................. 20 Complete I/O Board Connections......................................................................................................................... 21 Connect JAMMA Harness (For Kits – Not Included) ........................................................................................... 21 Connect the Control Panel Switches and Cable .................................................................................................. 21 Golden Tee GOLF™
Version 11/14
Page 1
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Connect Coin Door Lamps................................................................................................................................... 21 Connect the Trackball .......................................................................................................................................... 21 Connect RCA Audio Cables (Optional – Not Included) ....................................................................................... 21 Connect the USB Cable ....................................................................................................................................... 21 Connect High-Definition Television ...................................................................................................................... 21 Connect I/O Power Cable .................................................................................................................................... 21 Check All Connections ......................................................................................................................................... 21 Cabinet Graphics Installation ............................................................................................................................... 22 Marquee Installation ............................................................................................................................................. 22 Final Connections ................................................................................................................................................. 22 Coin Doors, Test Switch, and Volume Controls ................................................................................................... 23 Initial Power-Up .................................................................................................................................................... 23 SYSTEM SETUP MENUS.................................................................................................................................... 24 Navigating The Menu System .............................................................................................................................. 24 Entering System Setup Mode .............................................................................................................................. 24 Selecting a Menu ................................................................................................................................................. 24 Choosing a Menu/Option ..................................................................................................................................... 24 Changing a Value................................................................................................................................................. 24 Main Menu ............................................................................................................................................................ 24 Collections & Earnings Menu ............................................................................................................................... 25 Do Collection ........................................................................................................................................................ 25 General Settings .................................................................................................................................................. 26 Operator Adjustables ........................................................................................................................................... 27 General Adjustments ........................................................................................................................................... 27 Money Slot Adjustments ...................................................................................................................................... 28 Sound Adjustments .............................................................................................................................................. 28 Collection Settings ............................................................................................................................................... 29 Value Reset.......................................................................................................................................................... 30 System Tests ....................................................................................................................................................... 31 Video Tests .......................................................................................................................................................... 31 Color Test............................................................................................................................................................. 32 Contrast Test........................................................................................................................................................ 32 Screen Size Adjustment ....................................................................................................................................... 33 Sound Tests ......................................................................................................................................................... 33 Player Control Tests ............................................................................................................................................ 33 Mechanical Meter Test ......................................................................................................................................... 34 Hardware Tests .................................................................................................................................................... 34 Hardware/Software .............................................................................................................................................. 34 System Info .......................................................................................................................................................... 35 USB Info ............................................................................................................................................................... 35 Version Info .......................................................................................................................................................... 35 Check Hard Drive ................................................................................................................................................. 36 Check Cooling ...................................................................................................................................................... 36 Troubleshooting Shortcuts ................................................................................................................................... 37 Golden Tee Settings & Audits .............................................................................................................................. 37 Golden Tee Settings ............................................................................................................................................ 38 Casual Golf Spotlight Player ................................................................................................................................ 39 Spotlight Player Prize Settings............................................................................................................................. 39 Golden Tee Audits ............................................................................................................................................... 40 Player Cost Schedule .......................................................................................................................................... 41 Reset Leaderboards & Records........................................................................................................................... 41 APPENDIX A Troubleshooting Guide .................................................................................................................. 42 APPENDIX B – SHOWPIECE Input/Output Connections (I/O Power, Trackball, etc.) ....................................... 47 APPENDIX C Replacement Part Numbers .......................................................................................................... 48 APPENDIX D Nighthawk Component Diagrams ................................................................................................. 49 APPENDIX F Menu Navigation Shortcuts ........................................................................................................... 55 Game Icon Descriptions ....................................................................................................................................... 55 APPENDIX G Mounting Templates ..................................................................................................................... 57 Trackball Mounting Template............................................................................................................................... 59 Button Templates ................................................................................................................................................. 61 Golden Tee GOLF™
Version 11/14
Page 2
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
NOTE
PLEASE RETAIN ORIGINAL SHIPPING BOX FOR SERVICE AND REPAIR.
Do NOT perform any installation or repair when the cabinet is powered on.
Make sure the cabinet is unplugged from all power sources before and during
installation.
Some game features may not be allowed in certain state or local jurisdictions.
Be sure to check your local laws before activating or allowing any features that
may be questionable in your area. Adjust game settings from the System Setup
Menus. Refer to this manual for details.
Incredible Technologies cabinets are shipped with the USB cables disconnected
from the I/O Board and the Cabinet Identification Device (CID). This prevents
vibrations during shipment from damaging the contacts on the connectors.
These cables must be connected before operating the equipment.
IT recommends disconnecting these USB cables whenever transporting the unit.
Golden Tee GOLF™
Version 11/14
Page 3
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SHOWPIECE CABINET
SHOWPIECE CABINET CONTENTS
(1) Golden Tee Golf Showpiece Cabinet
Shipped inside a plastic parts bag attached to the front of the
cabinet:
(1) Marquee Header
(1) Power Cord
(1) Game Manual
(1) HDMI Cable
Shipped inside the cardboard sleeve on the top of the control
panel:
(2) Marquee Header Brackets
NOT Included with your Showpiece Cabinet
You will need to supply a digital display for the game's main
monitor, and an appropriate stand or wall mount. Be sure that the
stand or wall mount is UL listed. Incredible Technologies
recommends a 42" HDTV that supports 720p or 1080p for the best presentation, game play and earnings
potential. A list of Recommended Mounting Solutions can be found under Purchasing Info and Specs at the
following address on the IT web site:
http://amusement.itsgames.com/games/golden-tee-golf/specs
LEG LEVELER ADJUSTMENT
Once your game is in position at the location, it is necessary to adjust the leg levelers. The leg levelers will help
stabilize the game on an uneven floor, and help it from moving or shifting during game play. The game is shipped
with the two front and two rear leg levelers installed. Adjust the levelers as necessary to level and stabilize the
game.
MOUNT MAIN SCREEN DISPLAY
Position the Showpiece cabinet in front of an HDTV. Incredible Technologies recommends either a 720p or 1080p
flat panel HDTV from 42" or larger.
The HDTV can be mounted to a wall or to an appropriate display stand. There are many different types of wall
mounts and floor stands available through retail, wholesale and Internet outlets. Be sure that the wall mount or
stand you select must be UL listed. Check www.itsgames.com for some possible options. Be sure that the top of
the Showpiece cabinet has at least 24" clearance in all directions. Insufficient clearance may result in damage to
your display or player injury.
Recommended height for your display may vary depending on your location and player base. As a general rule,
the minimum height of the bottom of the display viewing area should be 42" from the floor.
INSTALL MARQUEE
Your Showpiece cabinet comes with a framed marquee header
that can be easily attached to the top of your monitor. The
brackets for the header are shipped inside a separate cardboard
insert labeled Parts – Do Not Discard within the cabinet
packaging. The insert is located on the top of the control panel.
First, attach the two brackets to the back of the universal
mounting plate you are using for your HD display. The brackets
share the same screws used to affix the display to the mounting plate, and are sandwiched between the plate and
the back of the monitor. Once the brackets are in place, slide the marquee frame onto the clips on the two newly
mounted brackets. Be sure the tab on the clips rest inside the channel on the marquee frame.
Golden Tee GOLF™
Version 11/14
Page 4
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
HDTV DIP SWITCH SETTINGS AND NIGHTHAWK SYSTEM
BOX
Before making any Nighthawk connections, make sure the USB cables are connected for the I/O Board
and CID. See Complete System Box Connections for details.
Nighthawk System Box
DIP Switch Settings for HDTVs
The DIP switch settings in your Showpiece cabinet have been factory set to accommodate a 1080p HDTV
connected through HDMI cables. DIP switch bank Sw201 on the I/O Board controls the video resolution for the
main monitor. If using a DVI-D or VGA connection, or for different resolutions such as 720p, use this chart:
Notes:
A reboot is required when changing resolutions
Video and audio connections to HDTVs vary, and may require additional cables not included with the Showpiece cabinet. Also, some displays
may not support the resolution needed for your game. Check your display's manual for additional information.
Golden Tee GOLF™
Version 11/14
Page 5
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
VIDEO CONNECTIONS FOR 720P/1080P HDTV
Golden Tee Golf Showpiece 2015 supports 1920x1080 (1080p) and 720p (1280x720) resolutions. Be sure your
HDTV is compatible.
For any questions related to Showpiece cabinet connections, see the Showpiece Connections Guide at
http://amusement.itsgames.com/service/manuals
If you plan to use a Single HDTV as your only video
output, follow the instructions below.
Connect to HDMI
Connect the HDMI cable (supplied) to the HDMI output on
the Nighthawk system. Route the cable through the clip
under the lock on the back wall, and down through the
access panel on the back of the cabinet. Connect the
other end of the HDMI cable to the proper HDMI input on
your television.
Set Up Your HDTV
Refer to the HDTV manual to adjust the video signal to
match the correct input for your game. Selecting the
correct input is commonly found from a system menu
accessed from the remote, or an Input Select button on the
HDTV.
Audio Connections for HDMI
The HDMI cable will also supply audio to the speakers on your HDTV. See Audio/Video Connections Table
below for details on other connection types.
Audio/Video Connections Table
Video Mode
Primary Video Connector
Audio
1920x1080 (HDMI) 1080p
HDMI with HDMI Cable
Digital – Via HDMI
cable
VGA
1280x720 (HDMI) 720p
HDMI with HDMI Cable
Digital – Via HDMI
cable
VGA
DVI-D to HDMI
Analog – Via 3.5mm
Y-audio from I/O
Board to Nighthawk
(green port)
VGA
VGA
Analog – Via 3.5mm
Y-audio from I/O
Board to Nighthawk
(green port)
Not Available
1280x720 (DVI-D) 720p
1280x720 (SVGA) 720p
Golden Tee GOLF™
Version 11/14
Secondary Video Connector
Page 6
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
INSTALL SECONDARY MONITOR FOR SHOWPIECE
If you plan to use Two TVs for your video outputs, follow the instructions below.
ABOUT THE SECONDARY MONITOR
Most Incredible Technologies games, including
Golden Tee GOLF, support a secondary monitor. The second monitor in Golden Tee displays unique information,
including game replays and advertising screens. Most other games from IT support a second monitor to display
the main game screen, so more of your players can see the action. Golden Tee GOLF can also show the main
display on the second monitor. See the System Setup Menus section of the Golden Tee 2015 manual.
FINAL CHECK
APPLY POWER
Connect the power cable to the socket on the back of the cabinet. Then plug the cable into a 3-pronged,
grounded wall socket. Locate the power switch on the back of the cabinet and turn it ON.
Note: If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its
service agent.
Watch the game carefully when you first turn it on. Look and smell for smoke. Turn it OFF immediately if there is
smoke. Make sure the fan inside the system box is running and the LEDs on the I/O Board are flashing. If not,
something is wrong, turn off the game.
Check the Cabinet ID Device (CID) Number
Watch the screen during boot-up and wait for the Golden Tee boot verification screen to appear. Note the
Cabinet ID Number (CID) that appears on this screen, and verify that it matches the CID number printed on the
back of the cabinet. The screen will automatically time out and boot-up will continue.
Check the Coin Switch and Bill Validator
Try the coin switch. Drop quarters or tokens through to check the coin mechanism. Insert a dollar bill into the bill
validator and listen for the credits to ring up. Make sure the game is adding credits and the correct quantity. You
can use the Player Control Test by pressing the System Setup button inside the coin door and entering the
System Tests Menu. Make sure all of the controls work.
Cabinet Temperature
The state of the art Nighthawk hardware is extremely powerful, and therefore generates a
substantial amount of heat. Measures have been taken to keep the various components
cool during normal use. If overheating occurs, game play and hardware longevity may be
affected. Use the Check Cooling menu in the System Setup menus to monitor the
temperature within your cabinet. Enter System Setup by pressing the System Setup button
inside the outer door of the coin vault. Once at the main System Setup menu, use the
trackball and Start button to select Troubleshooting Shortcuts, then Check Cooling.
Custom Adjustments
Upon initial power-up, the game will initialize to factory default settings. These settings affect game elements such
as number of credits per coin, volume settings, etc. The System Setup section in your game manual will describe
how to alter these settings and view the system audits or run system tests.
Golden Tee GOLF™
Version 11/14
Page 7
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GENERAL CABINET MAINTENANCE
Games that are in good working condition, with clear monitors, clean control panels and working trackballs will
make more money than a machine in poor condition. It is definitely worth your time and attention to protect your
investment with a little common care. Each week, clean the display and wipe down the control panel to bring
back that new game look. Test the trackball and buttons regularly to make sure they are playing properly. And
perhaps most important, make sure the coin mechanisms and bill acceptors are in good working order.
CARE AND CLEANING OF RUBBER BUMPER
The rubber bumper on the front of the cabinet’s control panel is made from durable nitrile rubber. Clean it using a
mild soap and water solution or blue window cleaner.
NIGHTHAWK AIR FILTER
The Nighthawk System Box comes equipped with an external electrostatic air filter. This filter is held in place by a
metal bracket, attached to the system box. The filter prevents debris from entering the system box and damaging
the electronic components. A clogged filter will impede airflow, thus building up unwanted heat which can cause
damage to your hardware. Be sure to check this filter at least once a month. Remove the filter by sliding it out of
its housing. Shake off excess dirt and if necessary clean it with soap and water. Be sure the filter is completely
dry before reinstalling the filter.
TRACKBALL MAINTENANCE
The trackball will require periodic maintenance to assure optimum performance. In most cases the inside of the
trackball simply needs to be cleaned of any accumulated dust and debris. See page 11 for Trackball
Replacement.
To access the inside of the trackball, remove the 6 Phillips head screws that hold the trackball together and
remove the top cover. Clean out any dust and debris inside the trackball. Polish the rollers and remove any
foreign material that may be on the rollers. Do not lubricate the bearings, as this will only attract more dust. If the
bearings do not spin freely it is best to replace the bearing assembly. Inspect the rollers for any nicks that may
cause poor performance and replace if needed. Inspect the ball for any nicks and replace if needed.
Parts can be obtained from Happ Controls and is an economical option rather than replacing the entire trackball
assembly.
It is critical that the green field ground wire be properly connected to field ground. This prevents the trackball from
building a static charge that can cause the game to lock up or reset. A static discharge can also damage the
trackball’s electronic components, as well as the main system.
CARE AND CLEANING OF COOLING FANS AND VENTS
The hardware that runs Golden Tee GOLF is quite sophisticated, and many of the chips and processors will get
hot very quickly. Like your desktop PC, the Golden Tee GOLF hardware needs adequate ventilation to work
properly. Dust and dirt can be a major cause to overheating and will lead to costly repairs. At least once a month,
check to make sure the cabinet and system box fans are working and free of dust and debris. Use a vacuum to
clear all the ventilation holes on the cabinet at this time as well.
CAUTION:
Incredible Technologies cabinets are shipped with the USB cables disconnected from the I/O
Board and the Cabinet Identification Device (CID). This prevents vibrations during shipment from
damaging the contacts on the connectors. These cables must be connected before operating the
equipment.
IT recommends disconnecting these USB cables whenever transporting the unit.
Golden Tee GOLF™
Version 11/14
Page 8
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SHOWPIECE CABINET REPAIR PROCEDURES
SYSTEM CHASSIS BOX
The Nighthawk Chassis houses most of the game electronics and hardware in one box that can be easily
installed. As with all electronic equipment, the Chassis box should be handled with extreme care. Shock, severe
temperature, or sudden impacts can damage the internal components that require costly repair.
Note: Turn off power to the cabinet and remove the power cord from the back of the cabinet when performing any of the following.
System Chassis Removal
1. Unlock the control panel and open to expose the Nighthawk
system box.
2. Disconnect all connections to the system box. Be sure all wires
and connectors are clear and out of the way. Label the
connectors for easy reconnection.
3. Loosen the 6 ¼" hex-head screws that secure the system box.
4. Carefully lift the system box off the screws and up out of the
cabinet.
System Chassis Installation
1. Unlock the control panel and open to expose the inside of the
cabinet.
2. Align the system box onto the 6 mounting screws of the internal
slanted panel. The connection ports face up. Once the system
box is in place, tighten the 6 ¼" hex-head screws to secure the
box to the panel.
3. Connect the required connections. See the Connections
Diagram for more details.
I/O BOARD
Note: The I/O Board is game title specific and is not interchangeable with other game titles produced by Incredible Technologies
on this system. Dedicated and Retrofit Kit I/O Boards are different and are not interchangeable.
I/O Board Removal
First, unlock the control panel and open to expose the interior of the Showpiece cabinet. Disconnect all
connections from the I/O Board. Label the connectors for easy reconnection and move them safely out of the
way. Next, remove the six ¼” wood screws that secure the board to the interior left side of the cabinet (as you
face the game). Carefully remove the I/O Board from the cabinet.
I/O Board Installation
Place the I/O Board in the proper location on the interior left side of the cabinet (as you face the control panel of
the game). Be sure it is oriented properly so the cables reach the board (the USB port on the I/O Board facing the
top of the cabinet). Secure the I/O Board to the side of the cabinet with the six ¼” wood screws. Use the factory
mounting holes if at all possible. Be sure the board does not “bow” or is not stressed in any way. Once mounted,
connect the appropriate connections.
Golden Tee GOLF™
Version 11/14
Page 9
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Cabinet Identification Device (CID)
This device contains a specific ID number that identifies your cabinet. The CID is a permanent number and must
be connected to the main system box via the USB cable and working properly in order for the game to operate.
CID Removal and Replacement
If for some reason you must replace the CID, disconnect the USB cable from the CID. This is the only connection
to the CID. Next, remove the four ¼” wood screws that secure the CID to the interior left side of the cabinet (as
you face the game). The CID is located above the I/O Board. To install a CID, mount the CID in the proper
location using four ¼” wood screws. The CID should be mounted so the USB port is facing the top of the cabinet
and the electronics are facing the wall.
Note: The Cabinet Identification Device should NEVER be removed from the cabinet, even when replacing any of the other
components. The CID is the cabinet’s PERMANENT Identifier, regardless of any other components.
CASH VAULT
The Cash Vault has been designed for optimal security. With the double-locking doors, service technicians can
read meters and enter System Setup mode with no access to the cash box.
Cash Vault Removal and Replacement
1. Unlock and open the outer door of the Cash Vault.
2. Using a T-15 Torx wrench, unscrew the card reader/button plate located on the right side by removing the
four #8-32 screws located at the top and bottom of the plate.
3. Disconnect the connectors for the coin meter and buttons.
4. Remove the plate and set it aside.
5. Remove the coin bin and the bill validator magazine to make it easier to work inside the vault.
6. Unplug the bill validator cables, and push the cables for the bill validator, buttons, and coin meter through
the 2 holes located in the back of the vault.
7. The Cash Vault is attached by upper and lower locking brackets. These are each attached with two
socket-head screws located within the vault.
8. Locate the socket-head screws on the top and bottom locking brackets. Remove the two bottom screws
using a 9/64” hex key and remove the bottom locking bracket. Make sure to note how it was installed.
9. Remove the two top screws and remove the top locking bracket, again noting how it was installed.
10. You can now pull the entire vault assembly out from the front of the cabinet. The vault is attached with
foam tape, so it will need to be pried out or pushed from behind to loosen the adhesive.
11. Reverse the procedure to install the new door.
Locks
The outer lock is a secure T-handle lock, commonly used in vending. To open, insert the key and turn it
clockwise until the lock-handle pops out. Next, rotate the lock-handle clockwise 90 degrees to open the outer
door.
The inner door has a lock installed above the System Setup button. This lock is unlocked by turning the key 90
degrees clockwise.
Volume and Service Buttons
Mounted inside the outer door are controls for Volume and System Setup. Press the Volume Up button to
increase the loudness of the sounds on the game, and press the Volume Down button to make your game
quieter. Press the System Setup button to access the game’s software menu system. The System Setup menus
cover a variety of important areas including collections, tests, game adjustments, and optional settings.
Golden Tee GOLF™
Version 11/14
Page 10
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Bill Acceptor
The dedicated cabinet ships with a MARS AE2481 D5 bill acceptor and is mounted on the cash vault door. The
default DIPswitch settings for this acceptor are ON = 1, 2, 4-7 and OFF = 3, 8.
Bill Acceptor Removal
Disconnect the cable to the bill acceptor. Remove the four 11/32” sized nuts from the mounting studs.
Disconnect the ground wire from the one lower stud. Then gently pull the accepter off the studs from the back
side of the coin door.
Bill Acceptor Installation
From the back side of the coin door, place the bill acceptor onto the four mounting studs. The faceplate will
protrude out the front of the coin door. Place the field ground wire on a lower stud, and install the four 11/32”
sized nuts on the mounting studs and tighten. Next, connect the bill acceptor cable in the cabinet to the mating
cable on the bill acceptor itself.
Stacker Removal
A blue slide switch is located at the bottom of the stacker. Engaging it allows the stacker to be removed.
Coin Mechanism
Coin Mechanism Removal
Loosen the two finger screws to release the securing braces. Slide the upper brace upward, and the lower brace
downward. The mechanism should pull straight out.
Meter
This 5-volt device is mounted behind the card reader plate next to the inner door of the coin vault. One lead of
the meter is connected to a +5 volt source and the other lead is connected to the appropriate signal wire. An
additional opening is available just below the meter, if a second meter is desired.
CONTROL PANEL
Opening the control panel provides access to all game controls and hardware components. To open the control
panel, simply use the supplied key in the lock on the back of the cabinet and lift from the back. The control panel
is hinged in front and will stay open when fully extended.
Soft Power Switch
A “soft power” switch has been added to the underside of the control panel, to assist in the update process. This
switch will turn off power to the cabinet so you don’t have to reach around to the main power switch located on the
back of the cabinet.
Note: If you turn power off using the Soft Power Switch, you must use this same switch when turning power back on.
Trackball Replacement
To replace a trackball, open the control panel and remove the 4 long screws holding the trackball in place. Be
careful not to lose any of the screws, washers and lock washers. Disconnect the wire harness and ground wire
and remove the old trackball. Position the new trackball in the proper orientation over the existing standoffs.
Make sure that the arrow on the trackball that points to the monitor is pointing up. Replace the 4 long screws and
washers. Do not over tighten! Screw in until the lock washer is fully compressed. Reconnect the wiring
connector and ground wire.
Note: The field ground wire is critical to avoid electrical problems and assure optimal performance.
Golden Tee GOLF™
Version 11/14
Page 11
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Button Replacement
All of the buttons on the control panel require a 1 1/8th inch hole, and are pre-drilled on the dedicated control
panel. To remove a button, disconnect the wires from the button assembly by sliding the wires off of the micro
switch posts. Next carefully twist the micro-switch assembly off of the button posts. Finally, unscrew the nut to
remove the button from the control panel.
Place the new button assembly into the hole and position the smaller side of the micro-switch housing to face the
rubber bumper, angled towards the middle. Tighten the supplied nut using a pushbutton wrench. Do not over
tighten. Install the micro-switch by snapping it onto the pushbutton assembly by hand. Position the assembly so
the micro switch posts face the rubber bumper, angling towards the middle. Reconnect the wires by sliding the
wire assembly onto the contact posts of the appropriate micro switch. See the wiring diagrams in the back of this
manual.
L.E.D. Lighted Buttons
The Help and Options buttons on Golden Tee GOLF are Light Emitting Diode buttons. The
housing for the L.E.D. snaps into the back of the button assembly. The L.E.D. must be installed
properly for the light to function properly. The Anode/positive side of the L.E.D. is connected to
the +5 volts, and the Cathode/negative side of the L.E.D. is connected to the appropriate signal
wire. The L.E.D. slides into the housing and the housing is marked Positive and Negative. See the
lamps connector J202 in the cabinet wiring diagram in Appendix D.
Control Panel Removal
To remove the control panel from its hinge, Disconnect the trackball cable, field-ground wire, and
the control panel interconnect connector to the I/O Board. Remove the screw that attaches the
safety cable to the control panel. Remove the four ¼” screws holding the panel to the hinge.
Control Panel Graphics Removal
The control panel artwork has been screened onto a solid sheet of polycarbonate, which is
resistant to scratches and burns. Unfortunately long exposure to excessive situations may damage the surface
over time. To remove and replace this piece, the pushbutton and trackball assemblies must first be removed.
Separate the polycarbonate piece from the wood portion of the panel by starting at one corner and slowly peeling
the two apart. The overlay has adhesive on the entire surface and will take some force to separate the pieces
due to the adhesive. Once removed, the graphic overlay will not be able to be used again.
Control Panel Graphics Installation
To install a new polycarbonate graphics overlay, make sure the wood control panel surface is clean, smooth, and
free from glue, dirt and debris. Remove the paper protecting the adhesive from the new artwork/cover panel.
Carefully place it on the wood panel, aligning it properly. Press and smooth firmly to assure that it is secure.
Replace the buttons and trackball in the correct orientation.
SPEAKERS
The speakers are mounted in the bottom front of the cabinet, just below the coin vault. Sounds and speech are
important aspects to the play experience and should be adjusted and maintained for optimal results. Make sure
your speakers are in good working condition, are wired correctly, and are grounded properly to avoid buzz or hiss.
Speaker Access
In order to reach the speakers, unlock and raise the hinged control panel. The speakers are located just below
the coin vault. Remove the 4 nuts with an 11/32” nut driver to remove the speakers from their mounting.
Note: Both speakers must be identically wired to work properly. For optimal sounds, both speakers must be in phase with one
another. Be sure the positive wire is connected to the positive terminal of each speaker and the negative speaker wire is
connected to the negative terminal of each speaker.
Golden Tee GOLF™
Version 11/14
Page 12
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
OFFLINE KIT CONTENTS
Please refer to the IT part numbers in Appendix C when ordering parts.
(1) Golden Tee 2015 Nighthawk System Box
(1) I/O Board Assembly Golden Tee 2015
(1) Cabinet Identification Device (CID) for Golden Tee 2015
(1) HDMI cable
(1) Trackball Cable
(1) Input/Output Connections Cable
(1) Help Option Cable
(1) I/O Power Cable
(2) 6’ USB Cable
(1) A.C. Power Cable
(1) 3” Trackball, White
(1) Trackball Plate for 3”
(1) Card Reader Blanking Plate
(1) Pushbutton Assy., Red
(4) Pushbutton Assy., White
(1) Pushbutton Assy., Blue Round Illuminated
(1) Pushbutton Assy., Yellow Round Illuminated
(1) Marquee, GOLF 2015
(1) Control Panel Graphics Overlay, Golden Tee GOLF 2015
(1) GoldenTee.com Card
(1) Manual, Golden Tee GOLF 2015
(1) Quick Install Guide GOLF Kit
(1) Parts bag containing miscellaneous hardware
(1) *Fully-dressed Control Panel (Includes: assembled trackball, control panel overlay and buttons as a unit)
*There is an additional fee for kits with the fully-dressed control panel. If the fully-dressed control panel was not
ordered, the kit includes ONLY: trackball, control panel overlay and loose buttons NOT assembled.
RECOMMENDED TOOLS
Have the following tools ready before you begin to install this kit:

¼", 11/32" and 7/16" Sockets or Nut Drivers

Phillips Head #2 Screw Driver

3/16”, 7/32” and 9/32”, or 5/16”, 3/8”, and ¾” Drill Bits

1 1/8" and 3 1/2“ Hole Saw or Drill Bit

Small Flat Blade Screwdriver

Jig/Sabre Saw

Router

Push Button Nut Socket or Large Adjustable Pliers

X-acto® Knife or other Sharp Knife/Razor Blade

Wire Cutters

Scissors

Tape Measure

Putty Knife
Golden Tee GOLF™
Version 11/14
Page 13
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.




Decal Roller/Squeegee
Liquid Window Cleaner & Cleaning Cloth
Vacuum Cleaner
Any tools needed to remove parts from your existing cabinet not listed above.
INSTALLATION PREPARATION
BEFORE YOU START…
Before you install the Golden Tee GOLF kit into your cabinet there are a few things you should check first:
1. Check to make sure your existing cabinet's monitor, speakers, AC power cord, lights, bill acceptor and
coin mechanisms work. Replace or repair where necessary.
2. Check to make sure all the necessary parts are included in your kit. If any are missing/damaged please
contact IT's Technical Support at 847-870-7027 x121.
3. Check to make sure cabinet is wired with standard earth grounded AC plug compatible with local building
codes and/or safety requirements. If not, have a qualified electrician install one (not provided).
4. Have all the necessary tools available to install this kit. Refer to the recommended tools list to make sure
you are prepared before you start.
5. Make sure any parts of the system (lights, monitor, etc.) are not plugged in. Working with any part of the
system plugged in or powered on can be dangerous.
6. Keep in mind that it's been proven that the higher quality of work put into a kit installation results in a
higher earning game. Make sure you have plenty of space, time, and focus to put into this kit installation.
PREPARING THE CABINET
CABINET SELECTION
You can choose either a new cabinet or a used cabinet for your GOLF game. Reusing a cabinet is a costeffective way to maximize the return on your initial investment. In either case, all you need to provide is the
cabinet with a monitor, JAMMA harness, coin and bill acceptors, working fluorescent/marquee lights, and
speakers.
When selecting a cabinet, keep in mind that a larger control panel allows you to mount the trackball farther from
the monitor. This prevents players' hands from hitting the monitor glass when rolling the trackball forward, and
will earn better than a smaller control panel closer to the monitor. An older-model Golden Tee Golf dedicated
cabinet is ideal for this purpose.
If using an older IT cabinet made before 2005, such as Golden Tee 3D or Golden Tee Fore, consider ordering a
new Control Panel from Incredible Technologies. These control panels come pre-installed with controls and
graphics, and can save you considerable time and money through easy installation.
PREPARING THE CABINET FOR INSTALLATION
Follow these steps to prepare your cabinet before installation:
1. Remove the following from the cabinet: Main Logic Board(s) (and hard drive if present), Control Panel,
Monitor Viewing Glass, Marquee, and Power Supply. Now is a great time to clean both sides of the monitor
viewing glass and monitor screen to ensure a clear view of the game.
2. Thoroughly clean out your cabinet. Remove all of the old buttons, joysticks, etc. DO NOT remove monitor
and speaker wires or the wires that were previously hooked up to the control panel.
3. Remove the old graphics and adhesive from the cabinet including the control panel.
4. For a fresh look and best earnings, painting is highly recommended. Spray painting gives a better finish, but
if an airbrush or paint sprayer is unavailable a roller is second best. Remember to cover all exposed surfaces
not to be painted. When not installing into an existing Golden Tee Fore! dedicated cabinet, the
recommended color choice is black.
5. Make sure to have the sides of the cabinet and the control panel as smooth and flat as possible to allow for a
higher quality finish when applying the control panel background, labels, and side decals.
Golden Tee GOLF™
Version 11/14
Page 14
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
6. The "new game look" should always apply to the inside of your game as well. A few wire ties and shrink
tubing on your harness, some fastening hardware on your subassemblies, and a sweep with the vacuum
cleaner will help ensure that glitches do not occur.
Check JAMMA Harness and Wiring
The GOLF Kit comes with a special I/O Board that uses your cabinet’s existing JAMMA wiring harness. Make
sure your existing wires and connectors are in good working order. Check the JAMMA wiring diagram in
Appendix B - Kit.
Check Coin Mechanisms and Bill Acceptor
Make sure your coin mechanisms and bill acceptor are functioning properly, and your coin box and stacker are in
good condition. You want to make sure your game will accept money when players are ready to play.
Check Coin Door Connections
Your cabinet should already be wired correctly through the JAMMA connector. Now is a good time to make sure
your game can accept money. Check the JAMMA pinout chart in Appendix B - Kit for the correct wire colors and
pins. Trace the wiring to their sources and make sure they are connected properly and securely. Be sure the
wires are away from the coin door where they can be pinched or crimped.
Check Dedicated Monitor
For older cabinets, GOLF supports SVGA (800 x 600). GOLF no longer supports any resolutions below 800 x
600. However, to take advantage of the best and most current quality available, it is recommended to upgrade to
an SVGA compatible monitor or high-definition television.
Operating GOLF at the highest possible resolution will give your game the best results (and revenue). Many
standard cabinets contain a medium-resolution or VGA monitor already. If you have a low-res monitor, it may be
possible to switch it to a higher resolution. Check your monitor's manual for capabilities. If not, you should
consider upgrading to a newer monitor or high-definition television.
Check your CRT monitor for a DB15 VGA connector. If your current monitor has a DB15 VGA connector, it is
capable of VGA or SVGA resolutions. Check your monitor’s manual on how to switch the monitor to VGA mode.
Make sure the video dip switches on the I/O board match the resolution that the monitor is expecting. Plug the
video cable from the Nighthawk System box directly into the monitor. Be sure to disconnect the old composite
sync video cable from the monitor.
When operating with an SVGA or VGA monitor, GOLF uses the standard VGA sync timing and signals.
NOTE: In all cases a horizontal mount raster scan monitor is required.
CAUTION! Monitors are extremely dangerous and can result in severe injury. Make sure you follow and observe all
safety precautions as outlined in your monitor's manual. ALWAYS disconnect the power to the cabinet before working
on or around the monitor.
Golden Tee GOLF™
Version 11/14
Page 15
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CHECK HIGH-DEFINITION TELEVISION
GOLF supports 720p and 1080p resolutions that are compatible with newer flat-panel LCD digital televisions. In
addition, both 16:9 and 4:3 aspect ratios are supported. Refer to the Showpiece section of this manual for details
on connecting video and audio to a 720p/1080p HDTV.
NOTE: Video and audio connections to these displays vary, and may require additional cables not included in the GOLF kit.
In addition, some televisions may not support the resolution needed for GOLF. Check your television's manual for additional
information.
WARNING: Be sure top of cabinet has at least 18 inches or 45.7 centimeters of clearance in all directions. Insufficient
clearance may result in damage to monitor or player injury.
ELECTRONICS INSTALLATION
INSTALL NIGHTHAWK SYSTEM BOX
The Nighthawk System box houses most of the game electronics and
hardware into one box that can be easily installed. Verify that the
Nighthawk System box Power Switch is in the "ON" position.
1. Locate the area on the floor where the system box will be placed. Make
sure there is enough clearance to plug in cables.
 The Nighthawk System box measures 19" W x 7" H x 11" D.
2. Relocate and secure any wires to make room for the system box.
3. Place the system box so it sits flat on the floor and does not pinch wires.
Be sure there will be sufficient air flow to the system box. Overheating
can damage your system.
4. Mount the system box with 6 - #6 x ¾" Hex Washer Head Sheet Metal
Screws.
INSTALL CABINET IDENTIFICATION DEVICE (CID)
The Cabinet Identification Device or C.I.D. is an innovative and important component. This device permanently
identifies your cabinet as GOLF. It should remain even if another component such as the I/O board or system
box is replaced. The C.I.D. has a unique number to individualize the cabinet and is referred to as the Cabinet
Identification Number.
1. Attach the C.I.D. to the inside side of the cabinet
using the 2 - #6 X 1” Hex Washer Head Sheet Metal
Screws. Mount so the port is facing up and the
electronics face the wall.
2. Attach the USB cable from the Nighthawk System
box.
 Place the included Cabinet Identification Number
on the back of the cabinet for future reference.
Refer to this number to track your equipment
and whenever you are calling in for service.
 The Cabinet Identification Number is displayed in
the operator menus in the lower right hand
corner, and is labeled as Game ID. It is also
displayed near the bottom of the initial boot-up
screen.
Disconnect all CID USB cables before transport.
Golden Tee GOLF™
Version 11/14
Page 16
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
INSTALL I/O BOARD
NOTE: Before installing any electronics make sure cabinet power switch is
in the OFF position and the cabinet power is unplugged from the wall.
GOLF comes with a specially designed I/O board that works with
your cabinet's already installed JAMMA harness. The I/O board is
used as a connection interface between the JAMMA and the
Nighthawk System box.
Mount the I/O board inside the cabinet using 4 of the 6 x ¾" Hex
Washer Head Sheet Metal Screws, 1 in each corner. The existing
JAMMA harness edge connector will attach to this board. Do not
attach cables at this time.
NOTE: Route all cables AWAY from the I/O Board. Laying cables on top of or
below the I/O Board will result in unwanted noise or static during the game.
TRACKBALL AND BUTTON PREPARATION (FOR MOST KITS)
Mounting the trackball and buttons correctly and securely is very important for the profitability and safety of your
new game. This kit is designed for use in cabinets with ¾" thick wood control panels where proper routing of the
control panel is used to create a safe playing experience. If you do not have a ¾" thick wood control panel, please
replace your control panel or choose a cabinet with a ¾" thick wood control panel installed. Keep in mind that if
your current control panel has many old holes in it from previous buttons, joysticks, etc. that it may be easier to
start with a new solid control panel. This will give your game a better look and feel and help it to earn better.
Note: If the cabinet already has a trackball plate installed, discard and replace with the new trackball plate. The
metal trackball mounting plate and trackball mounting procedure have been designed to remove all bolts from the
playing surface. Routing the wood control panel is required so the metal mounting plate is flush with the panel
surface. An uneven playing surface or exposed edges will affect game play and could impact your earnings.
TIP: Trackball and button templates can be found in Appendix G of this manual. They include:

Trackball Orientation Diagram to orient your trackball correctly when installing.

Trackball Mounting Template to install the trackball plate and make the appropriate routing.

Button Set Templates to position and install control panel buttons.
Trackball Preparation
Install the metal trackball plate by following these steps:
1. Cut out the template from Appendix G with a pair of scissors along the noted line. Tape this template to
the top of the control panel as far away from the monitor as possible, making sure that the trackball will
clear the cabinet beneath it.
Note: Installing the trackball as far away from the monitor as possible will prevent players' hands from
hitting the monitor glass when rolling the trackball forward.
2. Using a sharp object, mark the eight points shown on the template on the control panel. Using a pencil,
trace the outside of the template. Remove the template.
3. Drill Holes 1-4 with a 9/32" or 5/16" drill bit.
4. Drill Holes 5-8 with a ¾" drill bit.
5. Route the crosshatched region to a depth of about .075" (about the thickness of a nickel).
6. Using a sabre saw cut out the center portion by cutting between holes 5-8.
7. Once you have cleaned up the routed area, install the trackball plate into the control panel using the ¼"
Flat Washers and ¼-20 Nylon Hex Nuts. Be sure the mounting plate is flush with the top of the control
panel.
Note: At this time you are only installing the trackball plate. Do NOT install the trackball or buttons until the control panel graphics
have been applied.
Golden Tee GOLF™
Version 11/14
Page 17
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Button Preparation
The following are the steps you should take to prepare your control panel for the installation of the button
assemblies:
1. Cut out the template(s) (see Appendix G).
2. Using a tape measure, measure the specified distances from the center of the trackball hole in the
trackball plate and make a mark the reference points indicated on the left and right button set templates
(see Appendix G).
3. Lay each template over the appropriate reference marking point. Mark the centers of the remaining holes
using a sharp object.
4. Drill a 1 1/8" hole at each marked point.
Once the installation is complete, be sure to use the System Controls test in the game’s System Setup menus to
ensure proper functionality of all the player controls.
CONTROL PANEL OVERLAY INSTALLATION
Golden Tee GOLF comes with an oversized control panel overlay that will accommodate a variety of existing
game cabinets, but works best on Golden Tee Fore!, NFL® Blitz™ and EA Sports™ PGA Tour® Golf cabinets.
Follow these instructions to correctly install the control panel overlay on one of these cabinets:
1. Make sure that the newly drilled control panel has a smooth, clean surface. Sand where necessary to make
sure the graphics are installed on an even surface.
2. Clean the control panel to make sure it is free from dust, grease, metal filings, etc. Make sure that all
residues (adhesive, overlay material, etc.) from the previous control panel graphics are removed. This will
ensure a clean, easy, and beautiful application of the control panel graphics.
3. It is very important that the trackball and control panel graphics be mounted perfectly straight. Find
the center of your trackball template and lightly draw vertical and horizontal guidelines on the control panel,
marking out your centering lines.
4. Remove a small section of the protective backing from the overlay. Carefully center the overlay over the
control panel by lining up the die-cut hole with the trackball template. Be sure the graphic is positioned
perfectly straight. Line up your pencil guidelines with the lines incorporated into the art. Once in position,
gently press down on the section with exposed adhesive, affixing the overlay into place. Once affixed, the
overlay cannot be removed.
5. While holding down the overlay over the attached area, very carefully turn over one side and remove the
exposed backing. Gently lay down the exposed overlay from the center outward, smoothing with your hands
or a roller as you go. Be sure the overlay remains straight and square. Repeat the process with the other
side of the overlay, so the entire surface is affixed to the control panel. Make sure all bubbles have been
pressed out for a clean, flat surface.
TIP: Liquid window cleaner can be sprayed onto the control panel before placing the overlay onto the control
panel. The window cleaner will allow the overlay to be positioned with less risk of damage to the overlay or
adhesive. Once in position, use a decal roller or squeegee to force any excess cleaner out. Be sure to add
additional time for the liquid to evaporate.
6. Using a razor knife (or other sharp instrument) carefully cut around the edges of your control panel, trimming
any excess material.
7. Find the center of each hole you have drilled out for the buttons and use the knife to poke a hole into the
overlay. Make a vertical and horizontal line (like a plus sign) from the center of the hole to the edges. You
should be able to place your button in later with no edges showing.
CAUTION: If you choose to install a Plexiglas® cover over your control panel (not recommended), to ensure the safety of your
players and the quality of your game make sure that all surfaces, edges and bolts that a player may come in contact with are
smooth, safe and secure.
Golden Tee GOLF™
Version 11/14
Page 18
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
FINISHING THE CONTROL PANEL
1. Reattach the control panel to your cabinet adjusting any hinges or chains where necessary. Make sure not to
pinch or crimp any wires while re-attaching the control panel.
2. Install the trackball into the trackball plate. The trackball must be oriented correctly in order to function
properly. Refer to the diagram located in Appendix G for correct orientation. You will need the following parts
in order to install the trackball correctly to the plate: 4 -10/32 x 2½" Phillips Head Machine Screws, 4 - #10
Flat Washers and 4 - #10 Split Lock Washers NOTE: Do not over-tighten the trackball. It will warp and cause
the trackball to not operate correctly.
IMPORTANT! Be sure to install your trackball securely, and maintain it regularly. Loose, worn, or incorrectly
mounted trackballs can result in decreased earnings and possible injury to players.
3. Secure the trackball ground wire to the trackball plate at the 8-32 stud on one end with an 8-32 KEPS nut and
the other end to the cabinet ground stud (usually located near the AC power cord inlet) using an 8-32 KEPS
nut.
4. Install the buttons in the holes located on your control panel. Make sure you use the red button assembly for
the Start button.
5. Attach the micro switches to your newly installed buttons and connect the wires up to the correct pins on the
JAMMA harness.
Note: The post on the switch labeled COM should connect to the ground wire and the post labeled NO should connect to the
signal wire. See the pin out chart in Appendix B.
WARNING: Trackball and trackball plate MUST BE GROUNDED to Earth Ground to prevent damage to the trackball, game
electronics or harm to operators.
Golden Tee GOLF™
Version 11/14
Page 19
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMPLETE SYSTEM BOX CONNECTIONS
Follow these procedures to correctly connect the various electronic components. Be sure the cables are
connected securely and in working order. Use cable clamps, with appropriate tension, where necessary to
ensure all cables stay in place during operation. Dress all cables with additional clamps and wire tie wraps where
needed. Avoid loose wires or disconnected cables, as they can cause an unneeded service call.
ATTACH I/O POWER, AUDIO AND USB CABLES

I/O board power cable. Connect from the I/O board to one of the two 4-pin power output connectors on the
system box.

Audio cables. Connect to the audio output jacks of the system box. Match the appropriate colors.

USB cable #1. Connect from the I/O board to any USB port on the system box.

USB cable #2 for Cabinet Identification Device (CID). Refer to the CID Installation Section for proper
orientation and placement of the CID.
ATTACH MAIN VIDEO CABLE
If your cabinet has a VGA or SVGA monitor, connect the video cable from the system box directly to the VGA or
SVGA monitor input.
If your cabinet has Medium or Low Resolution monitor, connect the video cable from the system box to the I/O
board.
If your monitor is a high-definition television, connect the appropriate video cable from the system box to the
television inputs. Refer to Appendix D for help with the available connection configurations.
Be sure to adjust your Dip Switch settings to match your monitor’s resolution. Refer to Appendix D.
ATTACH POWER CABLE
Use the AC power cord that is currently in your cabinet. The cord plugs into the System box. Have a qualified
electrician do the wiring. Verify A.C. main voltage selector switch is in the proper position. In North America the
setting is 115 volts AC. In some countries this should be set at 230 VAC.
Golden Tee GOLF™
Version 11/14
Page 20
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMPLETE I/O BOARD CONNECTIONS
CONNECT JAMMA HARNESS (FOR KITS – NOT INCLUDED)
Connect the JAMMA Connector to the I/O Board. Be sure it fits tightly and is oriented correctly.
CONNECT THE CONTROL PANEL SWITCHES AND CABLE
Snap the switches onto the buttons. Connect the Control Panel wiring harness using the JAMMA wiring chart
found in Appendix B - Kit.
CONNECT COIN DOOR LAMPS
Connect the coin door lamp cable to the pigtail off the I/O Power cable. If your cabinet originally had a Golden
Tee Fore! green PCB, then use the 9-pin connector. If your cabinet had a Golden Tee Fore! red PCB, then use
the 4 pin connector. Find the mating connector leading to the coin door to make your connection.
CONNECT THE TRACKBALL
Locate the Trackball Cable and connect it to the connector labeled Trackball on the I/O board. The other end will
connect to the trackball. Connect the green earth ground wire to the trackball plate.
CONNECT RCA AUDIO CABLES (OPTIONAL – NOT INCLUDED)
Locate the Audio Cables already connected to the system box, and connect them to the I/O board audio inputs.
Inputs are color coded, so be sure to connect red to red, etc.
CONNECT THE USB CABLE
Locate the 6 ft. USB Cable from the system box and connect it to the USB port on the I/O board.
CONNECT HIGH-DEFINITION TELEVISION
GOLF supports 1920x1080 and 1280x720 (HDMI, SVGA) resolutions for high-definition televisions. Refer to the
diagrams in Appendix D for the proper connection for your television. Be sure to set the Video Dip Switches on
the I/O Board (Sw201) to match your HDTV resolution.
CONNECT I/O POWER CABLE
Connect the I/O Power cable to the power input connector. Use the end with the pigtail. The other end connects
to the system box.
CHECK ALL CONNECTIONS
Go over your entire cabinet again and double-check all of the connections. Make sure that all connectors are
tight and secure and in their proper place. Look for frayed, broken or exposed wiring and repair as needed.
Bundle and wire-tie your wiring and secure it to the inside of the cabinet. A thorough and neat job now will save
you a lot of time and trouble in the future.
Golden Tee GOLF™
Version 11/14
Page 21
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CABINET GRAPHICS INSTALLATION
Included with your Golden Tee GOLF kit is a set of decals to place on the side of your cabinet and a brand new
marquee. This will help identify your new game as Golden Tee GOLF. By placing and installing these correctly it
can help give players instant recognition, even from a distance.
MARQUEE INSTALLATION
The following are the instructions for placing the new marquee in your cabinet:
1. Using the old marquee glass as a template, center the glass on top of your new marquee. Make sure that
all the printed images are visible.
2. Using an X-acto® knife or other sharp blade, score the new marquee deeply by following the edges of the
old glass as a guide.
CAUTION: Do not cut on table or counter top. Use a cutting board or a disposable surface.
3.
4.
5.
6.
Carefully break off any excess material you have cut off.
Be sure the light behind the marquee works.
Clean the glass on both sides to give players a clear view of the new marquee.
Install the marquee graphics and glass securely.
Golden Tee GOLF™
Version 11/14
Page 22
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
FINAL CONNECTIONS
COIN DOORS, TEST SWITCH, AND VOLUME CONTROLS
Wire the coin doors as per the JAMMA Harness Connection table in Appendix B - Kit. Connect the door lamps to
the appropriate (+12Vdc or +5Vdc) supply. Some games have separate power supply outputs for the lamps.
Install a test switch somewhere convenient inside the coin door area. This switch allows you to enter adjustables,
run diagnostics, and see or clear audits. Make it readily accessible through the coin door. Wire it to the Test wire
on the JAMMA Harness. GOLF has the ability to adjust volume at any time during a game. Install two push
button switches (not included) inside the coin door for easy access. Connect the switches to the JAMMA
harness. Refer to the JAMMA Harness Connection table in Appendix B - Kit.
INITIAL POWER-UP
There are several steps you should take when powering up your Golden Tee GOLF for the first time. This is a
quick checklist for you to follow when doing your first initial power-up:






Plug in the game and turn it ON; be sure the game powers up correctly into the attract mode.
Adjust volume levels to desired settings.
Adjust monitor settings for best picture.
NOTE: Sound and Video Tests are available through the System Tests Menu. They are beneficial when
making any adjustments. Proper monitor and sound adjustment is very important.
Try all money slots. Drop quarters or tokens through to check the coin mechanisms and insert a bill into the
bill acceptor. Make sure the game is adding credits.
NOTE: GOLF supports most bill acceptors. Installing a bill acceptor is highly recommended and will
increase your earnings. Refer to your bill acceptor’s manual for installation specifications. The bill acceptor
can be wired to coin door 3 on the JAMMA.
Test all of the player input controls. You can use the PLAYER CONTROL TESTS in the SYSTEM SETUP
MENU.
Upon initial power-up the game is set to factory default settings. These settings affect game elements such
as number of credits per coin, volume settings, etc. The SYSTEM SETUP MENUS section will describe how
to alter these settings for your location.
Congratulations! You have finished installing
Golden Tee GOLF!
Golden Tee GOLF™
Version 11/14
Page 23
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SYSTEM SETUP MENUS
NAVIGATING THE MENU SYSTEM
The System Setup menus cover a variety of important areas including collections, tests, game adjustments, and
optional settings. You should familiarize yourself with these menus, as they are designed to optimize your game
for your location and your business. Pay particular attention to the Collection menus, as they will detail how much
money to give to your location and help you maximize your investment.
ENTERING SYSTEM SETUP MODE
There are two ways to enter System Setup. Open the coin door and press the Test button to access the game’s
System Setup software menu system. Or, from the I/O Board, move the DIP switch SW202 position 4 to the ON
position. This switch needs to be moved back to OFF to exit the System Setup menus. Refer to the diagram in
Appendix D for all DIP switch settings.
SELECTING A MENU
A menu option can be selected at any time by rolling the trackball up or down or by pressing the Left or Right
buttons.
CHOOSING A MENU/OPTION
A menu option can be chosen at any time by pressing the Start Button.
CHANGING A VALUE
A value can be changed at any time by rolling the trackball left or right.
MAIN MENU
The Main Menu displays five main areas that make up System
Setup mode. Please familiarize yourself with these areas, as
they will help you maximize your earnings potential.
Collections & Earnings – See Page 25
This section displays your machine’s monetary activity, and
details the various areas for income and expenses. This
section should be reviewed during every collection, to make
sure you manage your split correctly.
General Settings – See Page 26
This area allows you to change operator adjustables, perform
system tests, and reset your game back to factory settings.
Troubleshooting Shortcuts – See Page 37
This section presents a variety of tests and menus that will help
you troubleshoot any problems you may be having with your game. The available sections are also accessible
through the other main sections.
Golden Tee Settings & Audits – See Page 38
This area allows you to adjust settings specific to Golden Tee GOLF including the player cost schedule, game
features, and game audits.
ITNet Settings (Not available on GT GOLF)
Golden Tee GOLF is an offline product. The ITNet menu is not available.
Exit
This will exit the System Setup menus and take you back into the game’s attract mode.
Golden Tee GOLF™
Version 11/14
Page 24
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLLECTIONS & EARNINGS MENU
This menu allows you to perform a collection or view various earnings and fees.
Do Collection
This section is used when making a collection. The various
screens will detail the cost breakdowns and show you how
much of the cash box is to be paid to the location. Please
take some time to familiarize yourself with this section. Using
it wisely can save you money.
Clear Unused Cash
Sometimes when you go to make your collection, there is
money in the game that has not been played yet. Use this
setting to clear the unused cash from the screen, so your
future collections will reconcile with game play.
Add Free Cash
Use this setting if you wish to add money to the game for free
plays that do not advance the hard meter.
Back
This will take you back to the Main Menu.
DO COLLECTION
This screen is the main collection screen. There is a lot of helpful information displayed that will help you with
your collection. It is highly recommended that you view this screen with every collection, and reset it when your
collection is complete.
This screen displays the following helpful information:
Collection Date Range
The displayed dates are from your last collection until
today.
Days In Operation
The number of days the machine was active and available
for play since the last collection.
Reset
Highlight this to reset the number of days in operation field.
Total Income
The total income your machine made for this time period.
More Details
This brings up a second menu that further details income amounts.
Golden Tee GOLF™
Version 11/14
Page 25
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Total Fees
The total of the various fees that need to be set aside before making your split.
More Details
Select this to display a breakdown of the various fees, including Hardware Upgrade fees and tax splits.
Note: Hardware Upgrade Fees are included for your convenience, to help you cover the costs of owning and operating your
equipment.
Balance
The total income minus the total fees.
Operator Portion of Balance
The amount of the collection that the operator keeps.
Operator Owes Location
The amount of the collection that you pay your location.
Back
If you do NOT wish to perform a collection and reset the audits, highlight Back to exit this screen and return to the
Collections & Earnings menu.
Do Collection and Exit
If you wish to perform a collection and reset the audits (recommended), highlight Do Collection and Exit and press
Start. This will set all the fields in the Do Collection screen to zero. Be sure to empty your cash box at the same
time, so these screens will match the money at your next collection.
GENERAL SETTINGS
The General Settings menu houses various adjustable settings relating to the cabinet, and is divided into two
sections.
Operator Adjustables
This area allows you to adjust options like volume, attract
mode sounds, collection settings and money slot settings.
System Tests
This area allows you to perform diagnostics including
video adjustments, input tests, and sound tests.
Back
This will take you back to the Main Menu.
Golden Tee GOLF™
Version 11/14
Page 26
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
OPERATOR ADJUSTABLES
This menu contains adjustable settings that pertain to you and your business. Please familiarize yourself with this
section, as it can help you maximize the game’s earning potential.
General Adjustments
This area allows you to adjust options like coin message
and money modes.
Money Slot Adjustments
This area allows you to adjust the settings of your various
money slots on your cabinet.
Sound Adjustments
This area allows you to adjust the various sound settings
including attract mode sounds, game volume, and stereo
setup.
Collection Settings
This important area allows you to adjust various fees and
splits for your collections.
Reset To Factory Settings
This option allows you to reset all the settings found in the Operator Adjustables section to factory defaults.
Back
This will take you back to the General Settings menu.
GENERAL ADJUSTMENTS
Coin Message
The default is set to Insert $.
Accept Credit Card (Not available)
This selection is not available on Golden Tee GOLF.
Game Mode
This lets you toggle between money/free play. The default
is set to Money Play.
2nd Monitor Mode
You can add an external monitor to your dedicated or kit
game by connecting it to the appropriate video output on
the Nighthawk Chassis. Use this setting to select from
SVGA and S-Video signals. NO LIVE/CK GOLF
2nd Monitor Output
A second monitor can be added to clone the main monitor output.
Advertisements
This option allows you to “Show All Ads” or turn ads off.
Back
This will take you back to the Operator Adjustables menu.
Golden Tee GOLF™
Version 11/14
Page 27
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
MONEY SLOT ADJUSTMENTS
Money Slot 1 (all machines)
This adjusts how much one pulse equals for Money Slot 1.
The default is set to $0.25.
Money Slot 2 (kits only)
This adjusts how much one pulse equals for Money Slot 2.
The default is set to $0.25.
Money Slot 3
This adjusts how much one pulse equals for Money Slot 3.
The default is set to $0.25.
Credit Card (Not available)
This selection is not available on Golden Tee GOLF.
Reset Values
This resets all values to their default value located on this
page.
No
This will not perform the reset and take you back to the previous menu.
Yes
This will perform the reset and take you back to the previous menu.
Back
This will take you back to the Operator Adjustables menu.
SOUND ADJUSTMENTS
In Game Volume
This option lets you adjust the In Game volume from OFF
to 100%. The default is set to 30%.
Attract Volume
This option lets you adjust the Attract Mode Volume from
OFF to 100%. The default is set to 30%.
Attract Mode Sounds
This adjusts how often sounds are played in the attract
mode: Never, Rarely, Sometimes, Often, and Always. The
default is set to On - Sometimes.
Stereo/Mono
This option is where you select stereo or mono setup. The default is set to Stereo.
Reset Values
This resets all values to their default value located on this page.
Back
This will take you back to the Operator Adjustables menu.
Golden Tee GOLF™
Version 11/14
Page 28
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLLECTION SETTINGS
Golden Tee GOLF allows you to adjust costs and
percentages for the various income types that are received.
Use this menu to determine how much you want your
location to help you pay for these charges and services.
Set Hardware Update Fee
This menu allows you to adjust the Hardware Update Fee.
This fee is included for your convenience, as a method to
have the location pay for part of your equipment. The
default value for 2015 machines is $0.00 per week. Adjust
this value to an appropriate amount for your location.
Note: Hardware Update Fees are included for your convenience. No income is sent to IT on Golden Tee GOLF.
Operator/Location Income Splits
Use this menu to fine-tune your splits for any generated
income. The default settings are displayed on the
accompanying screen.
The adjustable settings refer to income generated from:
Cash
Player Account (Not available)
Credit Card (Not available)
ITNet Money Card (Not available)
Operator Money Card (Not available)
Golden Tee GOLF takes cash only.
Operator/Location Fee Splits
Use this menu to determine how you wish to split the
various fees with your location.
ITNet Fees (Not available)
Prize Fund Fees (Not available)
Credit Card Fees (Not available)
Communication Fees (Not available)
Software Update Fees (Not available)
Hardware Update Fees
Golden Tee GOLF is an offline product and has no fees or
income from online sources.
Hardware Update Fees are added for your convenience if
you wish to have the location help pay for your equipment.
Golden Tee GOLF™
Version 11/14
Page 29
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Tax Settings
Many states require special taxes or license fees that affect
your bottom line. Use this menu to separate these costs
from your collection before making your normal split.
Set Tax Rate
This menu allows you to adjust your current tax rate
percentage.
Set Tax Type
This menu helps you determine what part of the collection
is taxed, and who pays for these taxes.
Set Tax Split
This menu allows you to split the tax fees with the location.
Reset to Defaults
This menu will set all of the collection settings to their
factory default values. A verification screen will display to make sure you agree to the change.
Back
This will take you back to the Collection Settings menu.
VALUE RESET
This menu will reset ALL settings in the Operator
Adjustments section to their default values. A verification
screen will display to make sure you agree to the change.
Please Note:
This process may take several minutes to complete.
Golden Tee GOLF™
Version 11/14
Page 30
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SYSTEM TESTS
This area allows you to perform diagnostics including video adjustments, input tests, and sound tests.
Video Tests
This area has tests that will help you to adjust your game’s
color, contrast, and screen size.
Sound Tests
This area has tests that will help you adjust your game’s
audio setup by playing a stored sound, a streaming sound,
and testing the speaker(s).
Player Control Tests
This option allows you to test all inputs including trackball,
buttons, and money slots.
Mechanical Meter
This test makes the hard meter adjust by one to make sure
it is functioning properly.
Hardware Tests
This area includes a series of diagnostic screens and tests to help you make sure your game is functioning
correctly.
Back
This will take you back to the General Settings menu.
VIDEO TESTS
The Video Tests section has a variety of tests that will help you adjust your monitor.
Color Test
This area will take you to a series of tests to adjust your
monitor’s RGB settings to have each color display
properly.
Contrast Test
This area will take you to a series of tests to adjust your
monitor’s brightness/contrast so the game displays
properly.
Screen Size Adjustments
Use this screen to align your monitor so that all the circles
appear as circles and the boundary line appears on the
edge of each side of the screen.
Back
This will take you back to the System Tests menu.
Golden Tee GOLF™
Version 11/14
Page 31
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLOR TEST
Color Grid Adjustment
Adjust your monitor to have each colored box display
properly.
Red Screen
Adjust your monitor to have red display properly.
Green Screen
Adjust your monitor to have green display properly.
Blue Screen
Adjust your monitor to have blue display properly.
Back
This will take you back to the Video Tests menu.
CONTRAST TEST
White Screen
Adjust your monitor to have white display properly.
50% White Screen
Adjust your monitor to have 50% white display properly.
25% White Screen
Adjust your monitor to have 25% white display properly.
Black Screen
Adjust your monitor to have black display properly.
Contrast Screen
This option is a test you can use to adjust your monitor’s
contrast and brightness settings to have the boxes
displayed properly.
Note: May not work on older or often used monitors. If you have a monitor that's old or has been used often you may not be able
to adjust the contrast and/or brightness levels accordingly. In this case adjust the monitor for best performance while getting close
to the recommended settings.
Contrast Screen
This option is a test you can use to adjust your monitor’s
contrast and brightness settings to have the boxes
displayed properly.
Back
This will take you back to the Video Tests menu.
Golden Tee GOLF™
Version 11/14
Page 32
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SCREEN SIZE ADJUSTMENT
Use this screen to adjust the size and aspect ratio of your
picture. Press the Start button to exit.
If you are using an HDTV display, you may need to adjust this
screen to see the complete image. Use the trackball to
highlight BIGGER or SMALLER and press the Start button to
adjust the screen image. Press DONE to exit.
Note: Adjusting the screen size will prompt a reboot upon
exit of this menu.
SOUND TESTS
Stored Sound
This will play a stored sound so you can make sure your
audio setup is functioning properly.
Streaming Sound
This will play a streaming sound so you can make sure your
audio setup is functioning properly.
Speaker Test
This test will say MONO if you have your game set to Mono
or LEFT and RIGHT if you have it set to stereo so you can
make sure your audio setup is functioning properly.
Back
This will take you back to the System Tests menu.
PLAYER CONTROL TESTS
Use this screen to test all of the inputs, including the trackball,
buttons, and money slots. When an input is active the
appropriate graphic image will light. Press the Left, Right and
Start buttons simultaneously to exit this test screen.
When testing the trackball, the Current value will change
depending on the direction the ball is spinning. The Max
value will display the largest number reached during the test.
There is no exact number to determine whether a trackball is
malfunctioning, but in general the Max number should be
close to the same when spinning up and down, and close to
the same when spinning left and right.
When testing coin and bill acceptor switches, the number of
pulses read will be displayed below the appropriate image.
Golden Tee GOLF™
Version 11/14
Page 33
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
MECHANICAL METER TEST
Click Meter
This test makes the hard meter adjust by one to make sure
it is functioning properly.
Back
This will take you back to the System Tests menu.
HARDWARE TESTS
This area includes a series of diagnostic screens and tests to help you make sure your game is functioning
correctly.
Hardware/Software
This area has options to view your system, USB and version
info.
Check Hard Drive
This test checks the integrity of your hard drive’s data. Note:
This test can take several minutes.
Check Cooling
This test helps you make sure your game is functioning at
the proper temperature and all fans are working.
Check Card Reader (Not used on Golf)
This selection is not available on Golden Tee GOLF.
Back
This will take you back to the System Tests menu.
HARDWARE/SOFTWARE
System Info
This is a list of your game’s current basic system info.
USB Info
This is a list of your game’s current USB devices.
Version Info
This is a list of your game’s software version information.
Back
This will take you back to the Hardware Tests menu.
Golden Tee GOLF™
Version 11/14
Page 34
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SYSTEM INFO
This is a list of your game’s current basic system
information, including Hard Drive, CPU and Video Card.
Back
The Back button takes you back to the Hardware/Software
menu.
USB INFO
This is a list of your game’s current USB devices.
Back
The Back button takes you back to the Hardware/Software
menu.
VERSION INFO
This is a list of your machine’s software versioning.
Back
The Back button takes you back to the Hardware/Software
menu.
Golden Tee GOLF™
Version 11/14
Page 35
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CHECK HARD DRIVE
Check File Data
This test checks the integrity of your hard drive’s data.
Select Begin Test to initiate the process.
Note: This test can take up to 3 hours to complete.
If this test succeeds you will see the message: Status:
Hard Drive Functioning Properly. If this test fails, you will
see the message: Hard Drive Error (#)
Select Back to skip the test and return to the Check Hard
Drive menu.
Check File System
This test REBOOTS YOUR GAME and performs a low level
systems check of the integrity of your hard drive.
Note: This can take several minutes.
Back
This will take you back to the Hardware Tests menu.
CHECK COOLING
This checks that your game is functioning at the proper
temperature and all fans are working. The current status is
color-coded for easy viewing. If the results are displayed in
green, your cabinet is at normal settings.
Back
The Back button takes you back to the Hardware Tests
menu.
Golden Tee GOLF™
Version 11/14
Page 36
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TROUBLESHOOTING SHORTCUTS
This section gathers many of the commonly used tests and
menus into one convenient area. Check here first when
troubleshooting problems or questions about the integrity of
your machine.
The tests that are available in this section are:
Check Card Reader (Not available on Golf)
Check Cooling
Check Hard Drive
Screen Size Adjustments
Communications Settings (Not available on Golf)
Player Control Tests
System Tests
Descriptions of each of these tests and sections can be
found elsewhere in this manual.
Back
This will take you back to the Main Menu.
GOLDEN TEE SETTINGS & AUDITS
Golden Tee Settings
This section allows you to make custom adjustments to
certain features on your machine, such as the delay of
game timer.
Golden Tee Audits
This area allows you to view your money audits, game
purchase audits, and reset audits.
Player Cost Schedule
This option allows you to adjust the amount of money it
costs a player to play various game types.
Reset Leaderboards & Records
This area allows you to clear any or all local Leaderboards
and high score screens. Note: This process may take
several minutes to complete.
Back
This will take you back to the Main Menu.
Golden Tee GOLF™
Version 11/14
Page 37
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GOLDEN TEE SETTINGS
LIVE Prizes (Not available)
Prize play is not available on offline games.
Delay of Game Timeout
Adjust the timer that senses activity between shots.
Closest To The Pin LIVE (Not available)
Live play is not available on offline games.
Operator CTP
Activate the ability for the game to enter Closest to the Pin
(CTP) mode. This version of CTP does not display any
sponsored or branded game elements.
Hole-N-Win (Not available)
Hole-N-Win is not available on offline games.
More
Selecting More brings you to a second page of Golden Tee settings.
Locked Conditions (Not available)
Locked Conditions are not available on offline games.
Daily Prize Contest (Not available)
This feature is not available on offline games.
Difficulty
You can set the difficulty of the courses, to adapt the game
to the needs of your specific location. Difficulty settings can
be adjusted from 1 (easiest) to 5 (hardest). The default
setting is 2.
Pre-game Casual Clothing (Not available)
Players have a selection of all clothing prior to 2015
available.
Mulligans
Mulligans allow casual game players to retake a bad shot during their game. To disable this feature select OFF.
Allow Casual Straight Shots
This allows casual players the option to choose whether to play with only straight shots or to allow curved shots
as in standard settings mode. To disable this feature select NO.
Spotlight Player Settings
These settings allow local operators to offer prizes based on Golden Tee casual golf game play.
Reset Values
This will reset all Golden Tee Settings to their factory defaults.
Back
This will take you back to the Golden Tee Settings & Audits page.
Golden Tee GOLF™
Version 11/14
Page 38
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CASUAL GOLF SPOTLIGHT PLAYER
This allows operators to set the prize for a weekly
drawing based on all players who achieved a score of
PAR +17 or better.
Prize Settings
This opens This Week’s Prize Settings to set the prize
available for the winner of the drawing.
Clear Last Winner
This removes the last winner from the results.
Reset Values
This will reset all Casual Weekly Drawing settings
SPOTLIGHT PLAYER PRIZE SETTINGS
Edit Prize Text
Enter the text that best explains the prize offered. For
example, “Free dinner any week night to this week’s
winner!”
Remove Prize
Select this option if you do not wish to run a prize
drawing.
Golden Tee GOLF™
Version 11/14
Page 39
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GOLDEN TEE AUDITS
This section displays various counts and totals
for a number of game options. The following
values are based on the last reset, the date of
which is shown at the top of the screen.
Number of 1 hole purchases
Number of skins play purchases
Mulligans purchased
Coin Slot 1
Coin Slot 2
Bill Acceptor
Lifetime Money In
This field is cumulative and is not affected by
resetting the audits on this screen.
Casual curve shots chosen
Casual straight shots chosen
Reset Audits
This will reset all audits to zero, and update the date of the last audit reset. The Lifetime Money In field will not be
affected by this function.
Golden Tee GOLF™
Version 11/14
Page 40
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
PLAYER COST SCHEDULE
This screen details the costs of various play selections.
The player cost is shown as a total, with the Operator
Portion and the ITNet Portion broken out.
Play Golf (18 Holes)
This option lets you adjust how much it costs a player to
play an 18-hole game. The default is set to $3.00.
Play Golf (9 Holes)
This option lets you adjust how much it costs a player to
play a 9-hole game. The default is set to $2.00.
Play Golf (1 Hole)
This option lets you adjust how much it costs a player to
play a single hole of Golf. The default is set to $0.25.
Mulligans
This option lets you adjust how much it costs a player buy a Mulligan and repeat his shot in Casual Play mode.
The USA default is set to $0.25.
Skins (3 Holes)
This option lets you adjust how much it costs a player to play 3 holes in Skins Play mode. The default is set to
$0.75.
Skins (9 Holes)
This option lets you adjust how much it costs a player to play 9 holes in Skins Play mode. The default is set to
$2.00.
Skins (18 Holes)
This option lets you adjust how much it costs a player to play 18 holes in Skins Play mode. The default is set to
$3.00.
View Fixed Costs
This menu is not available on Golf.
Reset Values
This resets all values to their default value located on this page.
Back
Select this to return to the Golden Tee Settings & Audits menu.
RESET LEADERBOARDS & RECORDS
Use this menu to reset various machine-specific
Leaderboards.
Reset Leaderboards
This leaderboard is displayed after every hole during a
game. Use this setting to clear the current play data.
Reset Course Records
Course records, such as best score on each course, are
displayed on various screens during a game and in the
attract mode, and replayed in the game's attract mode.
Use this setting to clear all course records and game
highlights.
Reset All
Use this setting to clear all Leaderboards, course records
and game highlights.
Golden Tee GOLF™
Version 11/14
Page 41
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TROUBLESHOOTING & REFERENCE
APPENDIX A
TROUBLESHOOTING GUIDE
Video Problems
Symptom
No picture on the Monitor
Probable Cause
I/O Board DIP Switch settings are
wrong.
Incorrect video connection
configuration.
Monitor does not have a proper
A.C. voltage input.
Monitor is defective.
Nighthawk System box is defective
No picture but game sounds are
heard
Scrambled Picture
Incorrect video connection
configuration.
Since you hear game sounds the
system is working.
I/O Board DIP Switch settings are
set wrong.
Incorrect video connection
configuration.
Entire picture is not seen on the
screen or it does not fill the entire
screen
Misadjusted monitor.
Missing or washed out colors
Bad Video connections
Contrast and brightness on the
monitor needs to be adjusted.
Defective Monitor.
Golden Tee GOLF™
Version 11/14
Solution
Adjust DIP Switch settings to match
the resolution of the monitor you are
using. Refer to I/O DIP Switch
Settings in Appendix D.
Be sure the video connections are
correct according to the type of
monitor you are using. Refer to the
diagrams in Appendix D.
Verify A.C. power to the Nighthawk
System box. Verify monitor is
working on a known good system.
Repair or replace.
Go to Nighthawk System box
troubleshooting section.
Verify video is connected to the
system correctly. Refer to the
diagrams in Appendix D.
Review no picture troubleshooting
section above.
Adjust DIP Switch settings to match
the resolution of the monitor you are
using. Refer to DIP Switch Settings
in Appendix D.
Be sure the video connections are
correct according to the type of
monitor you are using. Refer to the
diagrams in Appendix D.
Adjust the monitor width and height.
Use video screen adjustment in
system tests. Refer to the monitor
manual.
Verify continuity from the monitor to
the video out on the I/O Board. Red,
Green, Blue video signal. Mid. and
Low resolution monitors only.
Refer to the monitor manual to make
adjustments.
Verify by connecting a known good
monitor to the system.
Page 42
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Sound Problems
Symptom
No audio
Probable Cause
Audio Cable between the I/O Board
and the Nighthawk system box are
not connected.
Speakers are not connected
properly.
Volume is set to the lowest level.
Attract mode sounds may be set to
all off. You will have sounds when
playing the game.
Defective I/O Board.
Defective Nighthawk system box.
DIP switch settings are incorrect for
your application
Distorted or scratchy game audio
Bad speaker.
Loose speaker or grill cover is
causing vibration.
Loose/defective audio cables from
the Nighthawk system box to the
I/O Board.
Defective I/O Board.
Defective Nighthawk system box.
Nighthawk Chassis Problems
Symptom
No video and no green lights on
the I/O Board. Fans are not heard
on the Nighthawk Chassis.
Probable Cause
No AC power to the Nighthawk
Chassis.
Power switch on the Nighthawk
Chassis is off.
Main cabinet power switch is off.
Soft Power Shutdown
Defective Nighthawk Chassis.
No video and no green lights on
the I/O Board. Fans are heard on
the Nighthawk Chassis.
Golden Tee GOLF™
DC power cord not connected from
Nighthawk Chassis to I/O Board.
Defective I/O Board.
Version 11/14
Solution
Verify audio cables are connected.
Refer to Appendix D.
Verify continuity from the I/O Board
speaker output pins to the speakers.
Refer to Appendix D.
Adjust the volume to an audible
level.
Choose one of the 5 Attract Mode
sound options in Sound
Adjustments.
Verify on a known working system.
Replace if necessary.
Be certain all other possibilities are
explored before replacing the
Nighthawk system box.
Refer to Monitor Applications at the
back of this manual for proper
setup.
Replace blown speaker.
Verify all components are installed
properly and securely.
Check the audio cable connections.
Replace cable.
Verify on a known working system.
Replace if necessary.
Be certain all other possibilities are
explored before replacing the
Nighthawk system box.
Solution
Verify A.C. voltage is connected to
the Nighthawk Chassis.
Flip the Nighthawk Chassis power
switch to on.
Be certain the main cabinet switch is
set to on.
Press the Soft Power button with the
power turned on. Or, short the top 2
pins of the 6-pin connector on the
system box. See Appendix D.
Be certain all other possibilities are
explored before replacing the
Nighthawk Chassis.
Connect the DC power cord from the
Nighthawk Chassis to the I/O Board.
Try it on a known good system.
Verify by disconnecting all cables
from the I/O Board except the DC
power and USB cable to the
Nighthawk Chassis. No green lights,
replace the I/O Board.
Page 43
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Control Problems
Symptom
Button does not work.
Button always indicates closed in
the player control test. Pressing it
will show it is not depressed.
Button always indicates closed in
player control test even with the
switch disconnected entirely.
Trackball is not functioning in any
direction.
Probable Cause
Switches Common post is not
connected to digital ground.
Signal wire is not connected to the
Normally Open post of the switch.
Switch is defective.
Signal wire is connected to the
Normally Closed post of the switch.
Defective I/O Board.
Test on a known good system.
Replace if necessary.
Trackball is not connected to the
I/O Board properly.
Verify the trackball is connected to
J208 labeled trackball on the I/O
Board.
Verify continuity on the trackball
Interconnect cable.
Replace trackball.
Replace I/O Board. Try it on a
known good system.
Verify continuity on the trackball
cable. Repair or replace if needed.
Repair or replace the trackball. Try it
on a known working system.
Repair or replace the I/O Board. Try
it on a known working system.
Clean the inside of the trackball.
Replace the rollers and bearings.
Do not over-tighten the trackball.
Tighten just enough to flatten the
lock washers.
Defective trackball Interconnect
cable.
Trackball is defective.
I/O Board is defective
Trackball does not work in a
certain direction.
Trackball cable is defective.
Trackball is defective.
I/O Board is defective.
Trackball works intermittently.
HDTV Video Problems
Symptom
Inside of the trackball is dirty.
Rollers are worn.
Trackball is over-tightened.
Probable Cause
Solution
Incorrect video cable configuration.
Be sure you are using the proper
cable connections. Refer to the
HDTV connections configurations.
Connected to the wrong output on
the system box
Refer to the HDTV connections
configurations.
Connected to the wrong input on
the HDTV
HDTVs usually have more than 1
input for a certain input type.
Examples are Component 1 & 2;
HDMI 1 & 2.
Incorrect input selected on the
HDTV
Be sure the correct input is selected
from the HDTV input menu.
Example: If using HDMI 1 that input
must be selected from the HDTV
video input menu.
DIP switch setting SW 201 on the
I/O Board set incorrectly.
Sw201 on the I/O Board must be
configured to match the method of
video you are using.
There is no picture during boot up.
Golden Tee GOLF™
Solution
Verify continuity to digital/power
supply ground.
Verify continuity from the I/O Board
to the Normally Open post of the
switch.
Replace defective switch.
Connect signal wire to the Normally
Open post of the switch.
Version 11/14
Page 44
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Symptom
Probable Cause
Solution
Normal black screen is displayed
for a period of time just before 3D
graphics are displayed.
This is normal operation. Be sure to
wait at least two minutes after
LOADING GAME is displayed to
see if video appears.
Your VGA cable is connected to
the second monitor output.
Connect the VGA connector to the
main output port.
Incompatible video mode
Many monitors will not accept SVGA
720p or 800 X 600. A commercial
grade HDTV will usually work.
Improper cable connection
Be sure the video cables are
securely connected at the computer
video card and at the HDTV. This is
especially critical if using a
component video cable.
Incorrect DIP switch configuration.
Be sure Sw201 is configured to
match the desired video.
Increase or decrease screen size in
games adjustments.
Location is in General
Settings>Operator>System
Tests>Video Screen
Settings>Screen Size Adjust
RCA audio cable is not connected
to the system box or HDTV
Connect the RCA audio cable to the
system box and then to the proper
input on the HDTV.
RCA audio cable is connected to
the wrong audio input of the HDTV
You must connect the audio cable to
the matching video input selected.
For example: If you are using
Component 1 the audio must go to
Component 1.
HDTV audio is muted
Turn the mute off in the HDTV
menu.
Volume is turned down on the
monitor or game sounds are set too
low.
Adjust the volume on the game to
75% and then adjust the game
volume to your desired level.
Low volume
Volume is turned down on the
monitor or game sounds are set too
low.
Adjust the volume on the game to
75% and then adjust the game
volume to your desired level.
Scratchy or distorted audio
Poor cable connection RCA cable
Be sure the RCA audio cable is
securely and entirely connected to
the mating connectors.
No audio
DIP switch settings are incorrect for
your application
Refer to Monitor Applications at the
back of this manual for proper
setup.
No picture after boot up
Distorted or fuzzy picture
Picture is too big for the screen or
does not fill the entire screen.
HDTV Audio Problems
No Audio
Golden Tee GOLF™
Version 11/14
Page 45
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Flash Code Messages
Flash Code (I/O Diode
D102)
Code Description
Solution
Flash Code 3
First Check Connections. Turn off game,
wait 10 seconds, turn game on. If
Possible IO board failure
Problem persists call IT tech support.
Turn off game, wait 10 seconds, turn
Info: Last reboot due to Watchdog time game on. If Problem persists call IT tech
out.
support.
Flash Code 4
Error When updating CID to latest
Version
Flash Code 2
Typically CID failure. Turn off game, wait
10 seconds, turn game on. If Problem
persists call IT tech support.
Turn off game, wait 10 seconds, turn
Updated USB CID was detected. This game on. If Problem persists call IT tech
is not an error but a notification.
support.
Flash Code 5
Flash Code 6
Flash Code 7
Flash Code 10
Flash Code 11
Flash Code 12
Flash Code 13
Flash Code 14
Check USB connection. Turn off game,
Disconnected Cabinet ID Device (CID) wait 10 seconds, turn game on. If
was detected.
Problem persists call IT tech support.
Turn off game, wait 10 seconds, turn
CID Malfunction. Typically CID is
game on. If Problem persists call IT tech
defective.
support.
Error When updating USB IO board to Turn off game, wait 10 seconds, turn
latest version. Typically an IO board
game on. If Problem persists call IT tech
failure
support.
Updated USB IO board to latest
Turn off game, wait 10 seconds, turn
version. This is not an error but a
game on. If Problem persists call IT tech
notification.
support.
Turn off game, Check USB and power
connections, turn game on. If Problem
A disconnected IO board was detected. persists call IT tech support.
Turn off game, wait 10 seconds, turn
IO board malfunction. Typically IO
game on. If Problem persists call IT tech
board has failed.
support.
This usually means the wrong type of IO
board. It does not match the system box
software. Try turning off game, wait 10
Game is incompatible with USB IO
seconds, turn game on. If problem
board.
persists call IT tech support.
Miscellaneous Problems
Symptom
Unable to exit Operator Menus.
No fluorescent light
Coin Meter is not working
Probable Cause
DIPswitch SW202 position 4 is in
the on position.
Test switch wired from the I/O
Board is closed.
No 120 volts A.C. power going to
the light fixture.
Defective fluorescent light.
Defective starter
Defective ballast.
Defective Coin Meter
Not wired properly
Defective I/O Board
Golden Tee GOLF™
Version 11/14
Solution
Set position 4 of SW202 to off.
Press start to exit.
Verify satellite test switch is not
closed.
Verify A.C. voltage to the light
fixture.
Replace fluorescent light.
Replace the starter.
Replace the ballast.
Replace with a known good one.
Connect one lead to +5 or +12 volts
depending on device. The other lead
to coin meter on Service Panel Pin
2.
Replace with a known good board.
Page 46
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX B – SHOWPIECE INPUT/OUTPUT CONNECTIONS (I/O POWER,
TRACKBALL, ETC.)
For Standard Online Kit and Deluxe Retrofit Kit
Trackball Harness Connector Pin Outs
I/O Power Cable Pin Outs
Pin Number
Wire Color
Function
I/O Board Connector
Trackball Connector
PIN WIRE #6 – Black
PIN WIRE #1 – Black
1
Yellow
+ 12 Volts DC
PIN WIRE #1 – Red
PIN WIRE #2 – Red
2
Black
Ground
PIN WIRE #2 – Yellow
PIN WIRE #3 – Yellow
3
Red
+ 5 Volts DC
PIN WIRE #3 – Green
PIN WIRE #4 – Green
4
Black
Ground
PIN WIRE #5 – Blue
PIN WIRE #5 – Blue
PIN WIRE #4 – Purple
PIN WIRE #6 – Purple
Control Panel J203 Connector Pin Outs
Pin
Color
Function
Lamps J202 Connector Pin Outs
Pin
Color
Function
1
Green-White
Options
1
Red-Black
Lamp Power – Buttons
2
Brown-White
Left
5
Red-Yellow
Help Lamp
No Connection
6
Red-Green
Options Lamp
Yellow-White
Right
3
4
5
Violet-White
Flyby
6
Black
Volume GND
7
Black-White
Spin
8
Blue-White
Help
9
Red-White
Start
10
Black
Ground
Speakers J301
Color
Pin
Pin
Function
Service Panel J206
Color
Function
1
Yellow-Red
Left Speaker +
1
Red-Black
2
Yellow-Green
Left Speaker -
2
Red-Green
Coin Meter
3
White-Red
Right Speaker +
3
Orange-White
Volume Up
4
White-Green
Right Speaker -
4
Orange-Yellow
Volume Down
6
Blue
Test
7
Black
Test Ground
No Connection
5
Coin Door J205
Color
Pin
Function
1
Red-Black
Lamp Power
2
Black
Lamp Ground
4
Black
Bill Ground
5
Grey-White
3
No Connection
6
Bill
No Connection
7
No Connection
8
Green-Blue
Coin 2
9
Red-Blue
Coin 1
Black
Coin Ground
10
11
Meter Power
No Connection
Golden Tee GOLF™
Version 11/14
Page 47
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX C
REPLACEMENT PART NUMBERS
Please refer to these IT part numbers when placing orders.
Part Number
925000341P
900146007R
915250304R
915000745
915000310R
915000173R
915015400R
999000060R
938291715
825100294R
999000288
900341000R
840500250R
925000341
815000341
820000341R
850000001R
850000003R
840675640
830000294R
900675340R
753304004
880000030R
885000030R
Description
SHOWPIECE CABINET, US GOLDEN TEE GOLF (OFFLINE) 2015
CABINET IDENTIFICATION DEVICE, GOLF
CABLE ASSY, I/O POWER FOR KITS
CABLE ASSY, POWER CORD. A.C.
CABLE ASSY, USB CABLE, 6 FT.
CABLE ASSY, TRACKBALL/GUN INTERFACE
CABLE ASSY, HDMI, 15 FT.
CARD READER BLANKING PLATE
CASH VAULT COMPLETE ASSEMBLY W/ $1-5 DBA
CONTROL PANEL OVERLAY GRAPHIC, DIECUT WITH CONTROL LABELS/TB HOLE
DBA, MARS $1-5 BILL ACCEPTOR FOR IT CASH VAULT ONLY MODEL AE2481D5E
I/O BOARD FOR GT GOLF 2015
GT.COM LOGO CARD FOR NON-TOURN. CABINETS
KIT – GT GOLF (OFFLINE) 2015
MANUAL, GT GOLF 2015
MARQUEE, GT GOLF 2015
PUSHBUTTON ASSY, RED WITH VERTICAL MOUNTED SWITCH
PUSHBUTTON ASSY, WHITE WITH VERTICAL MOUNTED SWITCH
QUICK INSTALL GUIDE, GT GOLF
SIDE DECAL, GT GOLF
SYSTEM BOX, GT 2015
SYSTEM BOX FILTER
TRACKBALL ASSY, 3" WHITE
TRACKBALL PLATE FOR 3" TRACKBL WITH STANDOFFS
Golden Tee GOLF™
Version 11/14
Page 48
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX D
NIGHTHAWK COMPONENT DIAGRAMS
Nighthawk System Box Diagram
I/O Board Diagram
Golden Tee GOLF™
Version 11/14
Page 49
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Showpiece & Kit Cabinet Connection Diagram
Golden Tee GOLF™
Version 11/14
Page 50
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
DC POWER CABLE
CID PCB
SOFT POWER (WHITE/YELLOW)
SOFT POWER (WHITE/ORANGE)
USB CABLE
AAEON B75 SYSTEM
BOX
15 PIN VGA
ADAPTOR
J1
USB
RIGHT
SPEAKER
GREEN/YELLOW
RIGHT SPEAKER - (WHITE/GREEN)
RIGHT SPEAKER + (WHITE/RED)
WHITE RCA JACK
3.5 MM STEREO ADAPTOR
AUDIO OUT
RED RCA JACK
.093 2PIN RECEPTACLE
GND (BLACK)
1
+12VDC (YELLOW)
2
GREEN/YELLOW
LEFT SPEAKER - (YELLOW/GREEN)
LEFT SPEAKER + (YELLOW/RED)
HDMI
.093 2PIN RECEPTACLE
GND (BLACK)
1
+12VDC (YELLOW)
2
ETHERNET
ETHERNET
PLUG AC FEMALE
LEFT
SPEAKER
X
USB
USB
AUDIO IN
DVI
LEFT (BROWN/WHITE)
OPTIONS (GREEN/WHITE)
SW-PB
SOFT POWER
UNDER
CONTROL
PANEL
SPEAKER
U209 PIN 9
U209 PIN 6
U209 PIN 5
1
2
3
4
+12V (YELLOW)
GND (BLACK)
+5V (RED)
GND (BLACK)
U209 PIN 4
U209 PIN 3
J103
USB
U209 PIN 2
U209 PIN 7
USB CABLE
1
2
3
1
2
3
LEFT
SW-PB
OPTIONS
SW-PB
SW-PB
SW-PB
7
6
5
VOL DOWN (ORANGE/YELLOW)
4
VOL UP (ORANGE/WHITE)
3
COIN METER (RED/GREEN)) 2
METER POWER (RED/BLACK) 1
3191 3 PIN RECEPTACLE
BILL (GREY/WHITE)
BILL GND (BLACK)
1
2
3
FLYBY
TEST GND (BLACK)
TEST (BLUE)
DBA POWER
110VAC
RIGHT
HELP
BLACK/RED
YELLOW/GREEN
WHITE/RED
11
10
9
8
7
6
5
4
3
2
1
.093 9 PIN RECEPTACLE
DBA
.093 9 PIN PLUG
COINS
1
2
3
4
5
6
7
8
9
AC HOT (BLACK/RED)
AC NEUTRAL (WHITE/RED)
BILL (GREY/WHITE)
BILL GND (BLACK)
COIN 1 (RED/BLUE)
COIN GND (BLACK)
LAMP GND (BLACK)
LAMP POWER (RED/BLACK)
TEST GND (BLACK)
TEST (BLUE)
VOL GND (BLACK)
VOL DOWN (ORANGE/YELLOW)
VOL UP (ORANGE/WHITE)
METER POWER (RED)
COIN METER (BLACK)
TEST
+5V
LAMP
1
2
3
4
5
6
7
8
9
SW-PB
SW-PB
J205 11PIN MINI KK
COINS
TEST
VOLUME
.062 3 PIN RECEPTACLE
.062 4 PIN RECEPTACLE
1
2
3
4
5
6
7
8
9
SW-PB
DEDICATED I/O PCB
1204 REV 1.1 RoHS
1
2
3
4
5
6
7
8
9
COIN 4 (GREY/BROWN)
LAMP GND (BLACK)
LAMP POWER (RED/BLACK)
COIN 3 (GREY/ORANGE)
COIN 2 (GREEN/BLUE)
COIN 1 (RED/BLUE)
BILL (GREY/WHITE)
BILL GND (BLACK)
COIN GND (BLACK)
TRACKBALL
.093 9 PIN PLUG .093 9 PIN RECEPTACLE
1
2
3
4
5
6
J208 6PIN MINI KK
TRACKBALL
+5V (RED/BLACK)
X DIR (YELLOW)
X CLK (GREEN)
Y DIR (VIOLET)
Y CLK (BLUE)
GND (BLACK)
CONTROL PANEL
GREEN
START
6
5
4
3
2
1
TRACKBALL
SPIN
COIN METER
.062 2 PIN RECEPTACLE
ANTENNA
1
2
3
4
5
6
.093 6PIN PLUG
BLACK
RED
YELLOW
GREEN
BLUE
VIOLET
SW-PB
U210 PIN 7
U210 PIN 6
U210 PIN 8
U210 PIN 9
Q206 COLLECTOR
U210 PIN 2
U108 PIN 13
U210 PIN 5
U210 PIN 4
U210 PIN 3
7PIN MINI KK
BLACK/RED
GREEN/YELLOW
WHITE/RED
2
1
+5V LAMP
1
2
3
4
+5V LAMP
SERVICE PANEL
J206
TRACKBALL
3191 3 PIN PLUG
MODEM COAXIAL CABLE
.093 6PIN RECEPTACLE
THERMAL CIRCUIT BREAKER
4A TYCO W28-XQ1A-4
HOT (BLACK/ORANGE)
HOT (BLACK)
LINE FILTER W/ IEC INPUT
BLACK/RED
3
2
1
COIN MECH 1
4
3
2
1
QUALTEK 857-10/033
2
1
(DBA)
BILL ACCEPTOR
DOLLAR
10
9
8
7
6
5
4
3
2
1
10PIN MINI KK
GND (BLACK)
START (RED/WHITE)
HELP (BLUE/WHITE)
SPIN (BLACK/WHITE)
VOL GND (BLACK)
FLY BY (VIOLET/WHITE)
RIGHT (YELLOW/WHITE)
4PIN MINI FIT JR. 5PIN MINI KK
LAMP POWER (RED/BLACK)
1
2
3
4
5
DC POWER
YELLOW/GREEN
HDMI CABLE
TO CUSTOMER SUPPLIED TV
RED RCA JACK
CHASSIS POWER
SJT CABLE UL1015 TYPE
8
7
6
5
4
3
2
1
8PIN MINI KK
USB CABLE
LAMP (RED/BROWN)
LAMP (RED/YELLOW)
WHITE RCA JACK
BLUE
LAMPS
J202
BROWN
USB
CONTROL PANEL
J203
USB
EARTH GROUND
NEUTRAL (WHITE)
WHITE/RED
GREEN/YELLOW
SW SPST
VAULT
SW-PB
VOLUME DOWN
SW-PB
VOLUME UP
SERVICE PANEL
COIN
METER
.062 2 PIN PLUG .062 4 PIN PLUG .062 3 PIN PLUG
COIN METER
VOLUME
TEST
GREEN
GREEN/YELLOW
YELLOW/GREEN
GREEN/YELLOW
AC HOT
GREEN
6PIN COMMONING CONNECTOR
BLACK/RED
1
2
BROWN
3
4
BLACK/RED
5
6
AC NEUTRAL
6PIN COMMONING CONNECTOR
WHITE/RED
1
2
BLUE
3
4
WHITE/RED
5
6
ON/OFF SWITCH
NKK JWL21RC2A
Golden Tee GOLF™
Version 11/14
Page 52
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX E
GNU General Public License
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program"
means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either
verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term
"modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with
the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof,
to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use
in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty
(or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to
view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based
on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections
of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this
License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections
as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose
permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the
right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume
of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is
normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which
the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy
the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to
copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or
distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and
conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the
recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and
any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not
Golden Tee GOLF™
Version 11/14
Page 53
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could
satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims;
this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license
practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on
consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system
and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries,
so that distribution is permitted only in or among countries not thus excluded.
In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any
later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the
Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to
ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes
make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE; THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the
public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the
exclusion of warranty; and each file should have at least the "copyright"
line and a pointer to where the full notice is found.
One line to give the program's name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation,
Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
Copyright 2004 Incredible Technologies, Inc. (IT). Certain programs, identified at IT's Website are free software subject to an
associated license.
1. Because certain programs are licensed free of charge, see it's website, there is no warranty for such programs to the extent permitted by
applicable law. Except when otherwise stated in writing the copyright holders and/or other parties provide those programs "as is" without
warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. The entire risk as to the quality and performance of those programs is with you. Should the programs prove defective, you
assume the cost of all necessary servicing, repair or correction.
2. In no event unless required by applicable law or agreed to in writing will any copyright holder, or any other party who may modify and/or
redistribute those programs be liable to you for damages including any general, special, incidental or consequential damages arising out of the
use or inability to use those programs (including but not limited to loss of data or data being rendered inaccurate or losses sustained by you or
third parties or a failure of those programs to operate with any other programs), even if such holder or other party has been advised of the
possibility of such damages.
A complete machine-readable copy of the source code of those programs and associated license is available to any third party, at the it
website.
Golden Tee GOLF™
Version 11/14
Page 54
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX F
MENU NAVIGATION SHORTCUTS
Change Collection Settings
 Push the red System Setup button inside the coin door
 Select General Settings menu
 Select Operator Adjustables menu
 Select Collection Settings menu
 Select the menu that you want changed
Add Operator Free Cash
 Push the red System Setup button inside the coin door
 Select Collection and Earnings
 Select Add Free Cash
 Move the trackball left/right to select the desired dollar amount
GAME ICON DESCRIPTIONS
Cooling Icon
The cooling icon (pictured right) will appear in the game's attract mode to warn you that
a fan is not operating at minimum recommended standards. If the fans do not operate at
suggested levels it may cause your game to overheat and fail.
Call Incredible Technologies Technical Support at 847-870-7027 x121 for assistance.
Golden Tee GOLF™
Version 11/14
Page 55
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 56
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX G
MOUNTING TEMPLATES
Golden Tee GOLF™
Version 11/14
Page 57
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 58
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TRACKBALL MOUNTING TEMPLATE
Golden Tee GOLF™
Version 11/14
Page 59
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 60
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
BUTTON TEMPLATES
Golden Tee GOLF™
Version 11/14
Page 61
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 62
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 63
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Golden Tee GOLF™
Version 11/14
Page 64
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Contact Information
IT Sales and Service
To purchase additional Golden Tee machines or any of IT's other fine products
please visit IT's website at www.itsgames.com and click on PRODUCTS!
General Numbers
IT Sales Hotline:
800-262-0323 x383
847-870-7027 x383
Technical Support, Warranty & Repair:
Parts and Customer Service:
Incredible Technologies, Inc.
800-262-0323 x380 or x381
847-870-7027 x380 or x381
847-454-9008 Fax
Incredible Technologies, Inc.
800-262-0323 x386
847-870-7027 x 386
847-454-9156 Fax
Operator Services:
Accounting
Incredible Technologies, Inc.
800-262-0323 x382
847-870-7027 x382
847-454-9155 Fax
Incredible Technologies, Inc.
800-262-0323 x382
847-870-7027 x382
847-454-9007 Fax
IT Mailing Address:
Incredible Technologies, Inc.
200 Corporate Woods Parkway
Vernon Hills, IL 60061
ITNet Registration Fax Number
847-454-9155
Sales Fax Number
847-454-9156
General Fax Number: 847-870-0120
Tech Services Fax Number: 847-454-9008
IT Vendor Information
Mars Technical Service:
Phone: 800-345-8172
Happ Controls:
Phone: 888-289-4277
GOLDEN TEE® GOLF, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc. All
Rights Reserved.
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their
respective owners. All rights reserved.
Incredible Technologies, Inc.
200 Corporate Woods Parkway
Vernon Hills, IL 60061
Phone (847) 870-7027 (800) 262-0323
www.itsgames.com
GOLDEN TEE® GOLF, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc. All
Rights Reserved.
© Copyright 2014 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their
respective owners. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising