OKI Bering Manufacturer Index

OKI Bering Manufacturer Index
Arcair
Vendor Code: ARC
Carbons
DC Plain Gouging Electrodes
General purpose electrodes without the copper coatings. Used on applications
where copper is considered detrimental. These electrodes contain the same
high quality blend of carbon and graphite as other ARCAIR electrodes.
Part No.
Description
STD
21-983-003
21-033-003
21-043-003
21-053-003
21-063-003
21-083-003
21-103-003
5/32 X 12 BARE
3/16 X 12 BARE
1/4 X 12 BARE
5/16 X 12 BARE
3/8 X 12 BARE
1/2 X 12 BARE
5/8 X 12 BARE
50
50
50
50
50
100
100
AC Pointed Copperclad Electrodes
Designed for use with AC power supplies. Rare earth material is added
to stabilize the arc, improving the operating characteristics.
Part No.
20-033-003
20-043-003
20-063-003
Description
3/16 X 12 AC-CC
1/4 X 12 AC-CC
3/8 X 12 AC-CC
STD
50
50
50
DC Copperclad Pointed Electrodes
A standard all purpose gouging electrode. Controlled copper coating
improves conductivity, providing more efficient, cooler operation and
helps maintain electrode diameter at the arc point.
Carbon Rods & Plates
Save time and money by using carbon rods and plates as holding devices when
you weld. Welding carbon products eliminate the need for many one-time jigs
and fixtures. They are excellent dams or molds for weld deposits. Carbon plates
are an excellent backup material when thin sections of metal are to be welded or
brazed together or onto thicker sections. In the thin to thick application they are
particularly useful since most of the heat is transferred to the thin section. A
section of carbon plate placed under the thin section will enable heat to flow more
evenly throughout the joint. Carbon plates are very useful in aluminum welding,
they prevent sagging of parts during the welding or brazing operation.
Part No.
Description
Part No.
Description
47-123-000
3/4X12 Rod
48-043-006
1/4X12X6 Plate
47-143-000
7/8X12 Rod
48-043-012
1/4X12X12 Plate
47-164-000
1X17 Rod
48-063-006
3/8X12X6 Plate
47-183-000
1-1/8X12 Rod
48-063-012
3/8X12X12 Plate
Part No.
Description
STD
47-203-000
1-1/4X12 Rod
48-083-006
1/2X12X6 Plate
22-023-003
22-983-003
22-033-003
22-043-003
22-053-003
22-063-003
22-082-003
1/8 X 12 DC-CC
5/32 X 12 DC-CC
3/16 X 12 DC-CC
1/4 X 12 DC-CC
5/16 X 12 DC-CC
3/8 X 12 DC-CC
1/2 X 14 DC-CC
100
50
50
50
50
50
50
47-243-000
1-1/2X12 Rod
48-083-012
1/2X12X12 Plate
47-283-000
1-3/4X12 Rod
48-103-006
5/8X12X6 Plate
47-323-000
2X12 Rod
48-123-006
3/4X12X6 Plate
48-123-012
3/4X12X12 Plate
48-163-006
1X12X6 Plate
48-163-012
1X12X12 Plate
DC Jetrod Copperclad Jointed Electrodes
RodHandler
Eliminates stub loss and provides continuous electrode feed for
semi-automatic and automatic Arcair Torches.
Holds and feeds filler rod while TIG or gas welding.
Simple to operate. Just insert the filler rod into the
loading port at the rear of the holder. Gently push the
filler rod through the drive rolls and out the wire guide.
Using the thumb wheel, the rod can be advanced until
it is extended from the holder.
Part No.
24-052-003
24-062-003
24-082-003
24-102-003
24-122-003
24-064-003
24-084-003
24-084-003
24-104-003
24-124-003
24-164-003
Description
5/16 X 14 DC-CC
3/8 X 14 DC-CC
1/2 X 14 DC-CC
5/8 X 14 DC-CC
3/4 X 14 DC-CC
3/8 X 17 DC-CC
1/2 X 17 DC-CC
1/2 X 17 DC-CC
5/8 X 17 DC-CC
3/4 X 17 DC-CC
1 X 17 DC-CC
STD
100
100
100
100
100
100
100
100
100
100
25
DC Copperclad Flat Electrodes
Specially designed for close tolerance metal removal; excellent for
removing weld crowns, repairing or making dies, removing welded
dogs and scarfing billets.
Part No.
35-099-003
35-033-003
Description
3/8X5/32X12 DC-CC Flat
5/8X3/16X12 DC-CC Flat
Part No. 8500-1900
Complete assembly. Right handed complete w/drive
rolls and guides for 1/16", 3/32", 1/8" filler rod
Arcair
Vendor Code: ARC
Angle-Arc Torches
Three torches with the new dimensions of versatility and productivity.
All three torches are designed for operator comfort.
• Natural 15° angle in torch
• 360° Swivel cable assembly
• Positive grip handle
• Reduced torch and cable weight
• Rugged construction
K2000™ Rated 450 AMPS
The K2000, the smallest member of the Angle-Arc family, is designed for
metal removal jobs in such places as repair shops, farms and ranches,
body shops and sheet metal shops just to name a few.
Electrodes: 1/8" to 1/4" (3.2 mm to 6.5 mm) round and 3/8" (9.5 mm) flat
Compressed air: 60 psi (4.2 kg/cm2) and 8 cfm (0.23 m3/min)
Weight: 3.6 Ibs (1.6 kg) torch and cable only
Part No.
Description
Ref.
61-046-001
K2000 Torch & 10' Cable
3
70-088-107
K2000 7' Cable Only
4
K2000 10' Cable Only
5
6
Part No.
Description
01-065-000
K3000 Torch Only
61-065-000
K3000 Torch & 7' Cable
61-065-001
K3000 Torch & 10' Cable
70-088-107
K3000 7' Cable Only
70-088-110
K3000 10' Cable Only
Insulator Assembly
94-433-193
94-433-193
94-433-183
Screw
97-142-009
97-142-009
97-142-009
Lever Assembly
94-476-080
94-476-080
94-476-066
Screw
97-192-125
2
K2000 Torch & 7' Cable
The K3000 is the medium-duty torch of the Angle-Arc family. This torch is
built for repair and maintenance jobs in areas such as mining, construction,
and all types of metal fabrication.
Electrodes: 5/32" to 3/8" (3.97 to 9.5 mm) round and 3/8" (9.5 mm) flat.
Compressed Air: 80 psi (5.6 kg/cm2) and 22 cfm (0.62 m3/min)
Weight: 4.0 Ibs (1.8 kg) torch and cable only
K4000
Part No.
1
K2000 Torch Only
61-046-000
K3000™ Rated 600 AMPS
K3000
Part No.
Description
01-046-000
70-088-110
K2000
Part No.
No.
97-192-127
97-192-127
Valve Bonnet Ass’y. (ltems 5 - 8) 94-104-016
94-104-016
94-104-016
Wrench
94-960-001
94-960-001
94-960-001
Bonnet
94-104-012
94-104-012
94-104-012
Spool Assembly (ltems 7 & 8)
94-801-011
94-801-011
94-801-011
7
O-Rings (2 Required)
94-710-036
94-710-036
94-710-036
8
Spool
94-801-010
94-801-010
94-801-010
9
Upper Arm
94-048-119
94-048-120
94-048-088
10
Head Assembly
94-378-354
94-378-355
94-378-334
11
Screw
97-192-022
97-192-022
97-192-022
12
Body
94-103-233
94-103-232
94-103-206
13
Hinge Pin
94-632-100
94-632-101
94-632-094
14
Spring
94-800-191
94-800-191
94-800-077
15
Handle
94-370-179
94-370-179
94-370-163
K4000™ Rated 1000 AMPS
The K4000 torch is made for heavy-duty metal removal applications such
as weld preparations in the pressure vessel shops and shipyards. This
torch can be fitted with a heavy duty cable for heavy gouging operations.
Electrodes: 5/32" to 1/2" (3.97 to 12.7 mm) round and 3/8" and 5/8"
(9.53 to 15.88 mm) flat.
Compressed air: 80 to 100 psi (5.6 to 7.0 kg/cm2) and 30 to 35 cfm
(0.85 to 0.99 m3/min).
Weight: 5.4 Ibs (2.4 kg) torch and cable only.
For the K2000/K3000 Cable Part #3 above has male threads
Ref.
No.
Description
K2000
K3000
K4000
Part No.
Part No.
Part No.
94-695-044
1
Retainer, Screw
94-695-054
94-695-054
2
“O” Ring
94-710-027
94-710-027
94-710-027
3
Connector
94-170-178
94-170-178
94-565-087
4
Washer, Spring
94-940-104
94-940-104
94-940-104
5
Washer, Flat
94-940-103
94-940-103
94-940-103
98-167-010
98-167-010
94-167-010
Part No.
Description
6
Clamp (2 Required.)
01-082-000
K4000 Torch Only
7
7' Conductor Assembly
96-130-314
96-130-314
96-130-263
61-082-000
K4000 Torch & 7' Cable
7
10' Conductor Assembly
96-130-315
96-130-315
96-130-261
61-082-001
K4000 Torch & 10' Cable
8
7' Replacement Cover
94-171-273
94-171-273
94-171-273
8
10' Replacement Cover
94-171-274
94-171-274
94-171-274
70-084-207
K4000 7' Cable Only
9
Boot, Insulating
94-105-014
94-105-014
94-105-014
70-084-210
K4000 10' Cable Only
10
Connector, Female
94-170-150
94-170-150
94-170-150
Page 14
Arcair
Vendor Code: ARC
Angle-Arc Torches
K5000 Torch & Cable
Now an angle-arc torch that will accept 5/8" carbon electrodes. This
torch will work in places where the user does not want to go to the large
Tri-Arc foundry torch, but the K4000 isn’t quite heavy enough. Will work
very well in foundry repair areas to gouge out casting defects in
preparations for welding.
Ref. No.
Part No.
Description
1
94-632-105
Hinge Pin
2
94-103-235
Body Assembly
3
94-800-205
Spring Assembly
4
94-476-085
Lever Assembly
5
94-433-202
Upper Insulator Assembly
6
94-048-121
Upper Arm
7
94-378-362
Head Assembly
8
94-433-204
Lower Insulator Assembly
9
94-104-016
Bonnet Assembly
10
94-370-189
Handle Assembly
11
94-013-110
Cable Adapter
12
94-170-150
Female Connector Assembly
13
98-167-002
Clamp (2 Required)
14
94-105-017
Insulating Boot
15
96-130-061
7 ft. Conductor Assembly
16
94-171-004
7 ft. Cable Cover
17
94-170-105
Male Connector
18
94-784-041
Swivel Sleeve
19
94-960-001
Spanner Wrench
Part No.
Description
01-105-000
61 -105-000
61-105-001
70-128-507
70-128-510
K-5000 Torch Only
K-5000 Torch & 7 ft. Cable
K-5000 Torch & 10 ft. Cable
7 ft. Swivel Cable
10 ft. Swivel Cable
K-3 Torch
Part No.
Description
01-064-000
K-3 Torch Only
61-064-009
K-3 Torch & 7 ft. Cable
61-064-010
K-3 Torch & 10 ft. Cable
70-088-907
7 ft. Swivel Cable
70-088-910
10 ft. Swivel Cable
Ref No.
Ref No.
Part No.
Part No.
Description
1
94-433-118
Insulator Assembly (items 1 & 2)
2
97-142-009
Screw (2 Required)
3
94-378-167
Head Assembly (items 3 & 4)
4
97-192-022
Screw
5
94-048-087
Upper Arm
Description
6
94-800-077
Spring
1
94-170-149
Male Connector
7
94-103-114
Body Assembly (items 7 & 8)
2
94-784-073
Sleeve
8
97-192-042
Screw
3
98-167-010
Clamp (2 Required)
9
94-370-079
Handle
4
96-130-264
7 ft. Conductor Assembly
10
94-476-034
Lever Assembly (items 10 & 11 )
4
96-130-265
10 ft. Conductor Assembly
11
97-192-154
Screw
5
94-171-273
7 ft. Cable Cover
12
94-632-094
Hinge Pin
5
94-171-274
10 ft. Cable Cover
94-104-016
Valve Bonnet Assembly (items 13-16)
6
94-105-014
Insulating Boot
13
94-801-011
Spool Assembly (items 13 & 14)
7
94-170-150
Female Connector Assembly
14
94-710-036
O-Ring (2 Required)
94-170-168
Male Connector Assembly (items 1 - 3)
15
94-104-012
Bonnet
94-170-157
Male Connector Assembly (items 1 & 2)
16
94-960-001
Spanner Wrench
Arcair
Vendor Code: ARC
Tri-Arc Foundry Torch
Three Torches
in One
Tri-Arc Foundry Torch
The Tri-Arc Torch has a heavy-duty all purpose body which accepts your
choice of interchangeable heads to remove defects, wash pads and perform
general purpose cleaning (see charts below). Maintenance is simpler and a
smaller stock of replacement parts is required.
The Tri-Arc Torch is 12-1/2" (31.8 cm) long and weighs only 2.4 Ibs (1.09 kg)
without the concentric cable. The standard Concentric Cable assembly is
7' (2.13 m) in length. Optional 10' Concentric Cable Assembly is available,
along with a water-cooled cable assembly.
Torch Only
Torch & Cable
Description
02-991-411
02-991-412
02-991-413
02-991-414
02-991-415
02-991-416
02-991-417
02-991-418
02-991-422
02-991-424
62-991-417
62-991-418
62-991-419
62-991-420
62-991-421
62-991-422
62-991-423
62-991-424
62-991-433
62-991-434
Torch without Heads
Defect Removal Torch
1/2" Padwashing Torch
5/8" Padwashing Torch
3/4" Padwashing Torch
1/2" General Purpose Torch
5/8" General Purpose Torch
3/4" General Purpose Torch
1" Padwashing Torch
1" General Purpose Torch
Defect Removal Heads
For removal of defects and fin removal
application.
Electrode Size
Inches
3/8", 1/2", 5/8", 3/4"
Head Assembly
Part No.
94-378-298
Padwashing Heads
For padwashing applications only. Heads
are fixed on a 35° electrode to work angle.
Electrode Size
Inches/mm
Head Assembly
Part No.
1/2" (12.70 mm)
94-378-286
5/8" (15.88 mm)
94-378-289
3/4" (19.05 mm)
94-378-283
1" (25.40 mm)
94-378-340
General Purpose Heads
For removal of defects, fin removal,
padwashing and piercing applications.
Ref No.
1
2
Part No.
Description
94-433-118
Insulator Assembly
97-142-009
Screw (2 Required)
94-476-034
Lever Assembly
97-192-154
Screw
3
94-048-110
Upper Arm Assembly
4
94-893-183
Air Tube
5
94-800-088
Spring
6
96-458-018
Jumper Assembly (2 Required)
97-112-035
Screw (4 Required)
7
94-104-012
Bonnet
8
94-801-021
Valve Spool Assembly
94-710-036
O-ring (2 Required)
9
94-632-063
Hinge Pin (2 Required)
10
94-103-221
Body
97-192-022
Screw
Electrode Size
Inches/mm
Head Assembly
Part No.
1/2" (12.70 mm)
94-378-267
5/8" (15.88 mm)
94-378-270
3/4" (19.05 mm)
94-378-273
11
94-370-079
Handle
1" (25.40 mm)
94-378-343
12
94-784-045
Sleeve
Page 16
Arcair
Vendor Code: ARC
Water Cooled Cable Assembly and Concentric Cable Assembly
340° Swivel Concentric Cable Assemblies
Extra Heavy Duty Cable Assembly
These concentric cable assemblies supply both power and air to the Tri-Arc
Torch. The 340° swivel gives the operator more freedom to maneuver the torch
around the workpiece with less fatigue. It also prevents cable twisting and
loosening of connections that could cause cable damage. All cables are
ruggedly built to withstand the severe operating conditions present in most
heavy-duty gouging environments.
Use with the Tri-Arc Torch when current requirements exceeds 1600 amperes.
The Cable Assembly was designed to operate at a maximum current setting of
2200 amperes. This cable is only available in a 7 foot length.
Part No. 74-161-907
Ref No. Part No.
Part No. 74-143-607
Part No. 74-143-610
Ref No. Part No.
7ft. Cable Assembly
10 ft. Cable Assembly
Extra Heavy Duty Cable
Description
1
94-170-176
Male Connector Assembly
2
94-784-078
Sleeve, Swivel
Description
3
98-167-012
Band-It Clamp (2 Required)
1
94-170-169
Male Connector Assembly
4
94-171-284
7 ft. Cable Cover
2
94-784-050
Sleeve, Swivel
5
96-130-286
Conductor Assembly
Clamp (2 Required)
6
94-105-019
Insulating Boot
94-171-006
7 ft. Cable Cover
7
94-170-174
Female Conductor Assembly
94-171-140
10 ft. Cable Cover
NS
94-105-020
Sleeve, Boot
3
4
5
98-167-012
96-130-063
7 ft. Conductor Assembly
96-130-126
10 ft. Conductor Assembly
6
94-105-007
Insulating Boot
7
94-170-095
Female Connector Assembly
Water Cooled Cable Assembly
The water cooled cable was designed for heavy-duty gouging or continuous
use with the Tri-Arc Torch. The cable design allows water to flow around the
copper conductor causing a cooling effect. This prevents the conductor
from overheating and melting the cable cover. The separate air line is
attached to the male connector to supply air to the torch.
Part No. 74-085-207
Part No. 74-085-210
Ref No. Part No.
7 ft. Water Cooled Assembly
10 ft. Water Cooled Assembly
Description
1
94-170-171
Male Connector Assembly
2
94-170-150
Female Connector Assembly
3
4
5
96-130-309
7 ft. Conductor Assembly
96-130-310
10 ft. Conductor Assembly
94-171-273
7 ft. Cable Cover
94-171-274
10 ft. Cable Cover
94-171-298
7 ft. Low Pressure Hose
94-171-299
10 ft. Low Pressure Hose
6
94-175-004
Air Hose Fitting
7
94-175-003
Water Hose Fitting
8
94-105-014
Insulating Boot
9
98-167-001
Clamp (6 Required)
NS
94-105-020
Insulating Sleeve
Arcair
Vendor Code: ARC
H-3 Torch
H-3 Torch
Part No.
Description
01-062-000
61-062-016
61-062-014
61-062-015
61-062-017
70-083-907
70-088-907
H-3 Torch, without Cable
H-3, complete w/ Swivel Concentric Cable Assembly
H-3, complete w/ Std Concentric Cable Assembly
Torch Assy 10' H3 w/ Concentric Cable
Torch Assy 10' H3 w/ Swivel Cable
Standard Concentric Cable Assembly (7 ft. Iong)
Swivel Concentric Cable Assembly (7ft. Iong)
Model H-3 is a general purpose Arcair torch which will groove, bevel, cut,
gouge, pierce or flush away any kind of metal. The Arcair torch saves time,
costs less to use, and gives a better finished job than older methods such as
grinding, chipping, etc.
The torch uses current from a welder, a special Arcair electrode and ordinary
compressed air. Both current and air are fed through the torch using the
same line, the Arcair Concentric Cable. An arc is produced between the
electrode and the metal to be cut or gouged, and the metal instantly melts.
At the same time, jets of compressed air come out of the torch head and
blast the molten metal away. The resulting cut or groove is bright and clean,
requiring no further preparation. Air flow is controlled by and on-off valve in
the torch handle. The torch head rotates for instant positioning of the
electrode to any desired angle. The metal parts of the torch are specially
selected for best electrical efficiency and long life. The insulators, lever and
handle are made of high impact, heat resistant materials for rugged service
and low maintenance. Model H-3 is 10-1/8" long and weighs 1-1/2 Ibs.
(without cable). Standard cable length is 7 ft., with maximum 10ft. Iength
available. Air and current are easily connected to the Arcair cable.
Electrodes
Ref No.
1
2
3
4
5
6
7
The H-3 can use 1/8", 5/32", 3/16", 1/4", 5/16" and 3/8" Arcair Copperclad
carbon electrodes. These special-blend electrodes assure superior arc
stability and greatest economy. Selection of size depends upon the width of
the cut or groove desired. DC electrodes are available in all the sizes listed
above, while AC electrodes are available in 3/16", 1/4", and 3/8".
8
9
10
Electrical Power
12
13
14
15
An ordinary welder is normally used as a power source. Care should be
taken that the welder is of sufficient size to produce the current required.
With DC electrodes, either rectifiers or motor generators are satisfactory.
AC electrodes are specially made for use with AC transformer welders. The
amperage required to operate this torch depends upon the diameter of the
electrode used.
16
17
18
Part No.
Description
94-378-007
97-192-022
94-433-024
94-142-009
94-048-016
94-048-017
94-476-003
97-182-006
94-940-019
94-800-013
94-800-014
94-433-017
94-370-008
94-103-200*
94-103-196*
94-386-007
98-718-003
94-103-202*
94-104-106
94-801-010
94-710-036
94-104-012
94-960-001
Head Assembly (includes head & screw)
Screw
Insulator Assembly (includes 2 insulators, 4 screws)
Screw, 4 Required
Upper Arm Assembly (includes arm, lever and screws)
Arm (alloy)
Lever Assembly (with screws and washers)
Screw (2 required)
Washer (2 required, not shown)
Spring & Insulators Assembly (includes spring & insulator)
Spring
Spring Insulator
Handle
Body Assembly (includes body, hinge, roll pin & valve body)
Body Alloy
Hinge
Roll Pin
Valve Body
Valve Bonnet Assembly
Spool
O-Ring (2 required)
Bonnet
Spanner Wrench (not shown)
* Torches purchased after 9-1-83 use these new part numbers
Electrode Size
1/8"
5/32"
1/4"
5/16"
3/8"
Min. Amps DC
30
90
300
350
450
Max. Amps DC
60
150
400
450
600
Min. Amps AC
300
350
Max. Amps AC
400
450
Air Requirements
Compressed air at 80 to 100 psi is used with the H-3. Air may be obtained from
the standard shop supply or from any suitable compressor. A 1-1/2 HP
compressor is sufficient for moderate use of the H-3, while a 3 HP compressor is
recommended for continuous operation.
Page 18
Part No.
Description
Parts For No. 70-083-907 CABLE
94-105-014
Insulating boot
94-170-158
Female Cable Connector
94-170-160
Male Cable Connector
94-171-273
Insulating Cable Cover (7 ft.)
96-130-247
Conductor (special wound, 7 ft. brazed end)
98-167-002
Clamp (2 required)
Parts For No. 70-088-907 CABLE
94-105-014
Insulating Boot
94-170-150
Female Cable Connector
94-170-168
Male Connector Assembly
94-171-273
Insulating Cable Cover (7 ft.)
96-130-264
Conductor Assembly (7 ft.)
98-167-002
Clamp (2 required)
Arcair
Vendor Code: ARC
Slice Torch and Striker
Slice Torch and Striker
The SLlCE Torch feeds oxygen and electrical power to a specially designed
SLICE Exothermic Cutting Rod. You supply oxygen and either a 12-volt battery
or a welding power supply. Either way, after turning on the oxygen and
touching the carbon steel cutting rod to the grounded workpiece or a striker
plate, the cutting rod ignites immediately. The SLICE Torch is sold complete,
ready to connect to a welding power supply or battery and an oxygen tank.
Safety features such as a protective hand guard and spark arrestor are built
into each SLICE Torch. The torch (Catalog No. 03-003-000) comes with a 10 ft.
(3.0 m) power cable and oxygen hose. It is also available with a Cam-lok
connector (Catalog No. 03-003-001 and 03-003-006) to make twist lock
connections with available packages.
Part No.
Description
03-003-000
SLICE Torch Assembly (#1 Cable)
03-003-001
SLICE Torch Assembly (#6 Cable)
03-003-006
SLICE Torch Assembly (#10 Cable)
72-012-002
Striker Assembly
The torch for the SLICE Cordless Striker Pack has a 10’ oxygen hose, but only
has a short cable pigtail for emergency use. The torch is 7.5" (19 cm) long and
weighs 7 lbs. (3 kg) with the cables.
An optional SLICE Striker (Catalog No. 72-012-002) may be purchased to
provide a convenient surface for igniting the rod with a 12-volt battery instead
of a welding power supply.
NOTICE
All SLICE torches come standard with the 1/4" Collet Chuck and Collet Nut. This
includes all torches in any SLICE Pack. To utilize the 3/8" rods the user must
order the 3/8" rod conversion kit which includes the 3/8" Collet Chuck and
Collet Nut.
Ref No.
Ref No.
Part No.
Description
1
94-370-166
Handle Assembly, Right Half
2
94-370-167
Handle Assembly, Left Half
3
94-777-109
Shield
4
94-168-022
1/4" Collet Nut Assembly
4
94-168-024
3/8" Collet Nut Assembly
5
94-158-048
1/4" Collet Chuck
5
94-158-045
3/8" Collet Chuck
6
94-940-109
Washer
7
94-305-009
Flashback Arrestor
8
94-378-338
Head Assembly
9
94-476-082
Lever Assembly
10
94-476-082
Oxygen Hose Assembly
11
96-130-279
Cable Assembly - #1
96-130-276
Cable Assembly - #6
96-130-319
Cable Assembly - #10
96-130-324
Cable Assembly - Pigtail
13
97-192-137
#10-32 X 3/8" Screw
14
97-192-129
#6-32 X 9/16" Screw (3 Req’d.)
15
94-168-023
Extension - 6"
16
94-940-108
Washer
17
94-777-111
Extension Shield
94-463-032
3/8" Conversion Kit
Part No.
Description
1
94-370-168
Handle Assembly (Right Half)
2
94-370-169
Handle Assembly (Left Half)
3
96-070-031
Striker Bar
5
97-132-002
#10-32 X 3/8" Screw
7
98-565-021
#10-32 Nut
8
97-192-130
#6-32 X 1-1/4" Screw
9
97-192-132
#6-32 X 3/4" Screw
SLICE® Exothermic Cutting Rods
SLICE exothermic cutting rods are designed specifically for use with SLICE
cutting systems. Their unique one piece patented construction maintains the
balance necessary to sustain the exothermic reaction. Once the oxygen flow is
started and the rod is ignited, it will continue to burn without electrical power,
as long as oxygen flow is maintained. The following is a list of the SLICE
cutting rods available:
Description
Flux coated
Part No.
Uncoated
Part No.
1/4"x 22" (7x559mm)
25 pcs.
42-049-002
43-049-002
100 pcs.
42-049-003
43-049-003
N/A
43-049-005
42-049-005
43-049-007
N/A
43-049-009
1/4"x 44" (7x 1118mm)
25 pcs.
3/8"x 18" (10 x 457mm)
50 pcs.
3/8"x 36" (10 x 914mm)
25 pcs.
Arcair
Vendor Code: ARC
Slice Packs
Slice Utility Pack Parts List
Part No. 63-991-026
The SLICE Utility Pack permits you to use the
exothermic cutting process to cut virtually any
metallic, non-metallic or composite material. This
package has the basic items needed to do a cutting
job packed in a rugged tool box. Just supply oxygen
and an ignition source and you are ready to cut. The
power cables on the torch and striker assemblies in
this pack should be used with a 12-volt battery only.
Also included is the collet extension and shield for
added protection when piercing.
Industrial Slice Pack
The industrial SLICE pack now gives you the versatility
of exothermic cutting and accommodates a larger
oxygen cylinder to extend your cutting time. The
industrial cart is capable of carrying a 9" diameter
cylinder. The industrial SLICE pack includes SLICE
torch and striker assemblies with 10' oxygen hose and
power cables. Also included is an industrial battery
charger for user convenience, 6" collet extension and
shield, regulator and a supply of cutting rods with rod
storage area. The user supplies their own 12-volt
battery to complete the system.
Part No. 63-991-021
Slice Cordless Striker Pack
Part No. 63-991-032
Included in Pack:
Igniter
Recharging Unit
Slice Torch
Supply of Rods
Collet Extension
The SLICE Cordless Striker Pack is the latest addition
to the complete line of exothermic cutting equipment.
The SLICE Cordless Striker uses two small lead-acid
batteries to supply a current surge sufficient enough
to ignite both the 1/4" and 3/8" bare SLICE Cutting
Rods.
You no longer need the cables that run from a torch
and striker to the battery. All of this has been put in
the hand held striker igniter. When it is time to
recharge just insert the igniter into one of the
receptacles on the recharging unit. The red light will
come on indicating the unit is charging. When the
green light comes on the igniter is recharged and
ready to go. The recharging unit is capable of charging
two igniters at a time, in less than four hours.
Part No.
Description
63-991-026
SLICE Utility Pack
03-003-001
Torch Assembly
72-012-002
Striker Assembly
89-250-845
Instruction Manual
94-134-049
Tool Box
94-168-023
Collet Extension Assembly
94-173-016
Coupling
94-777-111
Extension Shield
96-168-035
Clamp (Red)
96-168-036
Clamp (Black)
Part No.
Description
63-991-021
SLICE Industrial Pack
92-090-202
Cylinder Cart
94-134-042
Case
96-156-003
Battery Charger
94-861-003
12" Rubber Tie Down
97-001-041
U-Bolt
94-698-084
Oxygen Regulator
03-003-001
Torch Assembly
72-012-002
Striker Assembly
98-566-067
1/4 x 20 Nut (2 Required)
94-394-042
Rod Holder
94-166-079
Clamps (4 Required)
97-192-113
10-32 X 3/8" Screw (4 Required)
98-566-077
10-32 Acorn Nut (4 Required)
43-049-002
1/4" Cutting Rods (Qty 25)
94-960-063
Wrench
94-960-064
Wrench
94-168-023
Collet Extension Assembly
94-777-111
Extension Shield
96-168-035
Clamp Assembly (Red)
96-168-036
Clamp Assembly (Black)
89-250-845
Instruction Manual
Part No.
Description
63-991-032
SLICE Pack w/Regulator 120 VAC/60HZ
63-991-033
SLICE Pack w/Regulator 220 VAC/50HZ
94-134-047
Tool Box
03-003-008
SLICE Torch Assembly
72-012-007
Cordless Striker Igniter
96-076-034
Recharging Unit
96-076-030
Igniter and Recharging Unit
94-168-023
Collet Extension Assembly
94-777-111
Collet Extension Shield
94-173-016
Coupling
43-049-002
1/4 Uncoated Rods (25 Required)
89-250-845
Instruction Manual
72-012-007
Striker Igniter Parts List
94-370-187
Cordless Striker Power Cell
94-378-357
Head Housing Assembly1
94-070-090
Upper Striker Bar Assembly1
94-070-091
Lower Striker Bar Assembly1
94-105-024
Protective Head Cover
Note 1: Item #2, #4, #5 include mounting screws
Page 20
Arcair
Vendor Code: ARC
Slice Packs/Slice Equipment
Slice Pack Battery Unit
Part No. 63-991-003
The SLICE Battery Unit Pack now comes in a rugged
metal tool box. As with the utility pack you get all the
basic items needed to do a cutting job such as torch,
striker, and rods. Included in the Battery Unit is an
ignition source in the form of the 12-volt rechargeable
SLICE Battery Box Assembly. You also get the collet
extension and shield for piercing.
Part No.
Description
63-991-003
SLICE Battery Pack 120 VAC/60Hz
63-991-007
SLICE Battery Pack 220 VAC/50Hz
43-049-002
1/4" Cutting Rod (Qty. 25)
89-250-857
Literature Pack
96-076-021
Battery Box Assembly
94-134-047
Tool Box
72-012-002
Striker Assembly
03-003-006
Torch Assembly
94-168-023
Collet Extension Assembly
94-777-111
Extension Shield
96-130-297
Charging Cable,120VAC/60 HZ
96-130-296
Charging Cable,220VAC/50 HZ
94-173-016
Coupling
89-250-845
Instruction Manual
Slice Equipment Product Line Parts List
Battery Pack
Item
Complete Unit
Tool Box, Case, Cart
Torch
Striker
Cordless Igniter
Extension
Shield
Coupling
Clamp (Red)
Clamp (Black)
Instruction Manual
Rods, 1/4" x 22"
Battery Box Assy.
Charging Cable
Battery Charger
O2 Regulator Assy.
Wrench
Wrench
O2 Cylinder 55 cu/ft
Cordless Striker Pack
Utility Pack
120 VAC
220 VAC
120 VAC
63-991-026
94-134-049
03-003-001
72-012-002
_
94-168-023
94-777-111
94-173-016
96-168-035
96-168-036
89-250-845
_
_
_
_
_
_
_
_
63-991-003
94-134-047
03-003-006
72-012-002
_
94-168-023
94-777-111
94-173-016
_
_
89-250-845
25 uncoated
96-076-021
96-130-297
_
_
_
_
_
63-991-007
94-134-047
03-003-006
72-012-002
_
94-168-023
94-777-111
94-173-016
_
_
89-250-845
25 uncoated
96-076-021
96-130-296
_
_
_
_
_
63-991-032
94-134-047
03-003-008
_
72-012-007
94-168-023
94-777-111
94-173-016
_
_
89-250-845
25 uncoated
_
_
96-076-034
_
_
_
_
63-991-033
94-134-047
03-003-008
_
72-012-007
94-168-023
94-777-111
94-173-016
_
_
89-250-845
25 uncoated
_
_
96-076-036
_
_
_
_
63-991-021
92-090-202
03-003-001
72-012-002
_
94-168-023
94-777-111
_
96-168-035
96-168-036
89-250-845
43-049-002
_
_
96-156-003
94-698-084
94-960-064
94-960-063
_
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-287-013
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-~87-013
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-287-013
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-287-013
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-287-013
94-463-032
94-158-045
94-351-002
_
96-130-294
94-349-001
94-698-084
_
94-134-046
94-287-013
_
96-076-018
96-076-022
96-076-018
96-076-023
_
_
_
_
_
220 VAC
Industrial Pack
Accessories
3/8" Conversion Kit
3/8" Collet Chuck
Gloves
Harness Assy.
10' Cable/Hose Ext.
Shade #5 Goggles
O2 Regulator Assy.
O2 Cylinder 55 cu/ft
Oxygen Auxiliary Case
Exten/Shield Assy
Repair Parts
Replacement Battery
Battery Box Assy.
Arcair
Vendor Code: ARC
Protex Metalworking Chemicals
Protex® Original Anti-spatter
Protex Original
53-011-000
53-015-000
53-017-000
53-018-000
Protex Tip Dip
57-021-105
1 gal
5 gal
30 gal
55 gal
16 oz
Protex Zinc Rich
57-031-002
16 oz
Protex Coolant
57-106-100
1 gal
Protex Alclean
57-021-200
1 qt
57-014-000
1 gal
57-055-000
55 gal
Protex Extra
53-007-500
53-024-500
53-014-500
53-015-500
53-018-500
Protex Plus
57-021-106
7 oz Spray
24 oz Spray
1 gal
5 gal
55 gal
16 oz
The arc stabilizing base material used in Protex Original allows it to withstand temperatures of
approximately 1600°F. This product has been used to reduce scale build-up in a heat treating
operation. Protex Original can be diluted 1:1 with water before being brushed or sprayed on the
surface. One gallon of Protex Original diluted with a gallon of water will cover about 1000 square
feet (93m2). It will dry leaving a durable chalky base to protect the weldment. To remove Protex
Original, just brush the surface clean or use a mild detergent and water to remove the residue from
the surface. The chloride, fluoride and silicone contents in Protex Original have tested below a level
that makes it possible for use in nuclear work. If Protex Original freezes, the natural thickening
ingredient used in the material will become useless causing the compound to become thinner.
However, this will not effect the compound’s ability to reduce spatter. Water based Protex Original is
environmentally safe, non-toxic and non-flammable.
Protex Extra
Safe and non-flammable, Protex Extra contains no fluorocarbons or chlorinated solvents. Because
the new non-aerosol uses no chemical propellants, it is environmentally safe. It can be used on all
types of metals, including aluminum and stainless steel, without corrosion or discoloring in the weld
area. Water based Protex Extra is environmentally safe, non-toxic and non-flammable.
Protex Plus
Protex Plus is an aerosol anti-spatter that contains no chlorinated solvents, fluorocarbons or
silicones. Fixtures, weldments and tools can also be sprayed allowing spatter to be wiped or
brushed away after welding. For users preferring an aerosol product, Protex Plus is good for quick
applications. Protex Plus is environmentally safe and non-flammable. The use of an inert gas
propellant is less stressful to the environment.
Protex Clear
Because of its latex base, Protex Clear will provide a barrier that works for months to shield work
surfaces and fixtures from oxides and rust. The clear coat allows any identification marks to be
easily read and protected from environmental damage. Apply Protex Clear using a brush or standard
paint sprayer, perform the work, then remove if necessary. Because of Protex Clear’s latex base, total
removal must be done using an industrial grade cleaner or ammonia base solution. Protex Clear is
environmentally safe and non-flammable.
Protex Alclean
Protex Clear
53-014-201
53-015-201
53-018-201
1 gal
5 gal
55 gal
Brush or spray Protex Alclean on the work surface or use the solution as a dip bath to clean small
parts. Once parts are clean, just rinse away any remaining Alclean with water. Do not use Protex
Alclean on glass, galvanized, anodized, cadmium coated or painted surfaces. This compound may
discolor 2000 Series aluminum alloy.
Protex Tip-Dip
When the nozzle of the MIG gun is warm, simply dip into the gel. This will set up a film on the parts
to provide hours of protection. Protex Tip-Dip is non-toxic and non-flammable. Although Protex
Tip-Dip is non-flammable, contact with heat sources over 1000°F (538°C) may cause a temporary
flame-up. Therefore allow MIG gun nozzle to cool below the red hot state before dipping in Protex
Tip-Dip.
Underwater Products
Part No.
Description
Sea-Jet Cutting Electrodes
14-050-124
Sea Torch w/5/16" Collet
42-024-002
Electrode Sea Weld 1/8" 150/min
42-059-007
Electrode 5/16" Sea-Cut 150/min
42-066-006
Electrode 3/8" Sea Jet 50/min
42-075-005
Electrode Sea-Dragon 3/8" 50/min
94-158-044
Collet 5/16"
94-158-044
Collet 3/16"
94-158-047
Collet 1/8"
94-168-018
Collet Assembly
Sea-Cut I electrodes are a patented tubular steel
design used for oxygen-arc cutting. The outside
diameter is 5/16" (8mm) with a bore hole of .113
(3mm) diameter. These electrodes are coated with a
waterproof insulating material. They are NOT FLUX
COATED.
Page 22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising