EXT-200-LAN
USER MANUAL
HDMI Extender up to 200M Distance
EXT-200-LAN
1.Introduction
HDMI Over Ethernet is based on TCP/IP standard. It transmits your HD display with the high
resolutions up to 120 meters away from your HDMI or DVI-D source by using one CAT5e/6
cable. With the advantage of TCP/IP standard,you can extend your HD video to multiple
displays by using an Ethernet Switch.
HDTV Resolutions
480p,576p,720p,1080p
Audio
Sample rate:32kHz,44.1kHz,48kHz
IR remote control
38kHz;NEC
HDMI
HDMI 1.3
HDCP
HDCP 1.2
Power adapter
Input:100V-240V(50-60Hz) Output:5V/1A
Power consumption
HDMI Sender:3W HDMI receiver:3W
Size(L-W-H)
92x79x20mm
Weight
240g x 2
Operating Temperature/Humidity
0℃-70℃/10%-80%RH(no condensation)
Storage Temperature/Humidity
-10℃-80℃/5%-90%RH(no condensation)
2.Specifications
➢
Following TCP/IP standard.
➢
Support HDMI1.3 protocol.
➢
HDCP1.1 & 1.2 protocol compliant
➢
Support point-to-point mode, one point-to-many mode and cascade connection mode.
➢
Support IR extender function allows IR remote control of Source devices from remote
viewing location by sending IR commands received in the vicinity of the Display back to
the Source devices.
➢ Multiple Tx’s can be connected to a Managed Gigabit switch with VLAN/IGMP support
therefore sending 1080p video signals to Rx connected to the Gigabit switch to show
different sources on the HDMI displays. See further explanation in section 7. VLAN
Support
3.PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following
items are contained in the shipping carton:
1) Main unit No. 1 Sender , Main unit No. 2 Receiver
2) Two pieces of 5V DC Power Supply.
3) one piece of IR transmitter and one piece of IR receiver
4) Quick Set Up Guide
4.Panel Descriptions
HDMI Transmitter
5V/1A
Supply power for the Transmitter
Reset
Hold down the key for 5 seconds
IR-out
Connect IR transmitter this Port
HDMI-in
Connect HDMI sink source to this Port
HDMI Receiver
5V/1A
Supply power for the Receiver
Reset
Hold down the key,the model will re-start
IR-in
Connect IR Receiver this Port
HDMI-out
Connect HDMI sink device to this Port
5.Connection and operation
1) Connect the HDMI source (such as DVD, PS3, STB ) to the HDMI IN of Sender.
2) Connect the IR sender to the Sender IR OUT Port, and Be Directed at HDMI video source’s IR
receiver.
3) Connect the HDMI out of Receiver to HDTV display.
4) Connect the IR receiver to the Receiver IR IN Port.
5) Use one Cat5e/6 cable up to 120m to connect the Sender and Receiver.
6) Plug two pieces of 5V power supply into the Sender and Receiver.
7) Power on the HDTV display and HDMI source.
6.Application diagrams
Application 1 – Point To Point
Application 2 – Point To MultiPoint
6. IP settings – GUI
When typing the IP address as found on the Transmitter or Receiver he Graphical User
Interface is displayed. Connect the laptop or PC that is connected from the LAN port of the
laptop or PC to the RJ45 port of the Transmitter or Receiver. It is important to bring the IP
address of the laptop or PC in range with the IP address of the Transmitter or Receiver.
(see below)
6.1 Status Display
In Status Display the Device status is shown with System Version and Rate Config (Input
resolution and Output resolution. This is for Transmitter device or Receiver device.
6.2 System Config – Network config
In Network config the device IP settings can be modified to bring all devices in the same
range of your desired network. When you are using your production network it is advised to
bring the receivers and transmitter in a VLAN set up in order to keep the transmission data
for video isolated from your common network traffic.
6.3 System Config – Output display config
The output resolution can be changed by picking an available resolution fro the drop-down
list or you can match it with the Input resolution.
6.4 System Config – System update
If a new system version is available in order to upgrade potential new or improved
functionality this can be done by the System update button where a specific file can be
uploaded. This would only be needed when communicated by GeMNeXT.
6.5 Reset
To reset the device it is needed to press the Reset button on the back of the device for 5
seconds.
After this the device would be reset and this would automatically result in a changed IP
address to a default IP address. Please note this default address is not the IP address
described on the label on the device.
Transmitters:
192.168.1.168
Receivers:
192.168.1.160
If you need to bring the unit back to the required IP settings you had entered before please
change it back to those IP settings again. See 6.2 System Config – Network Config
6.6 Reboot
To reboot the device press the Reboot button in the Interface.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising