GE Profile DCCD330GDKC Installation instructions


Add to my manuals

advertisement

GE Profile DCCD330GDKC Installation instructions | Manualzz

GE Appliances

DCCD330GDKC/WC – GE ® Super Plus 7.0 Cu. Ft. Capacity Coin-Operated Gas Dryer

Dryer Dimensions (in inches)

42

36

Exhaust Options:

Shipped with exhaust to the rear.

When viewed from the front of the unit, exhaust 3-way via left, bottom and rear. Maximum recommended exhaust duct length is 15 feet of 4" rigid ducting with two 90° elbows and dampered wall cap.

(See Installation Instructions)

Requirements:

Gas – An individual branch circuit fused for 15- or 20-amp is required for each dryer.

Gas Dryer Rating:

120V, 60Hz

Gas (BTU/HR):

20,000. Factory equipped for natural gas. Tested for LP gas. A conversion kit is required for LP gas. Check installation instructions for correct kit number. Have a qualified technician install the conversion kit.

Equipped with energy saving Glo-Bar ignition.

Dryer Note:

Dryer wall outlet must be located within 36" of service cord entry and accessible when dryer is mounted in position.

Installation Information:

For complete installation information see installation instructions packed with product.

25-1/2

27

Specification Created 5/03

R

Listed by

Underwriters

Laboratories

For answers to your Monogram, ® GE Profile ™

GE ® appliance questions, visit our website at or

GEAppliances.com or call

GE Answer Center ® service, 800.626.2000.

GE Appliances

DCCD330GDKC/WC – GE ® Super Plus 7.0 Cu. Ft. Capacity Coin-Operated Gas Dryer

Dryer Exhausting Information – Use Metal Duct Only

Vertical and Horizontal Ducting

A

A

Domestic

Dryer Models

B

2-1/2

Best Performance

Maximum Length of 4"

Dia. Rigid Metal Duct

Exhaust Hood Type

Maximum Length of 4"

Dia. Flexible Metal Duct

Exhaust Hood Type

4

7.3 Capacity Electric and Gas Dryers

7.0 and 6.0

Capacity Models all Electric Dryers

7.0 and 6.0

Capacity Models all Gas Dryers

5.7 Capacity Electric and Gas Dryers

Number of

90°

Turns

0

1

2

3

4

2

3

0

1

4

0

1

2

3

2

3

4

0

1

A

4" Opening

150 ft.

140 ft.

130 ft.

120 ft.

110 ft.

90 ft.

60 ft.

45 ft.

35 ft.

25 ft.

90 ft.

60 ft.

45 ft.

35 ft.

60 ft.

52 ft.

44 ft.

32 ft.

28 ft.

B

2-1/2"

Opening

127 ft.

117 ft.

107 ft.

97 ft.

87 ft.

60 ft.

45 ft.

35 ft.

25 ft.

15 ft.

60 ft.

45 ft.

35 ft.

25 ft.

48 ft.

40 ft.

32 ft.

24 ft.

16 ft.

A

4" Opening

75 ft.

65 ft.

55 ft.

45 ft.

35 ft.

55 ft.

40 ft.

30 ft.

20 ft.

15 ft.

55 ft.

40 ft.

30 ft.

20 ft.

30 ft.

22 ft.

14 ft.

B

2-1/2"

Opening

52 ft.

42 ft.

32 ft.

22 ft.

12 ft.

45 ft.

30 ft.

20 ft.

15 ft.

10 ft.

45 ft.

30 ft.

20 ft.

15 ft.

18 ft.

14 ft.

10 ft.

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side

3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors. See installation instructions.

• The installation must conform with the local codes, or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces

0" both sides

3" rear

Specification Created 5/03

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all-rigid metal exhaust duct. If

“all-rigid metal” duct cannot be used, then “flexible all-metal” venting can be used, but it will reduce the maximum recommended duct length.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.

2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. The maximum length for flexible ducts are less than for rigid duct.

2.

A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a

90° elbow. A turn over 45° should be treated as a 90° elbow.

Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture and lint from being blown into the room. Gas dryers or any dryer located in a closet must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor

(crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc.

The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down.

Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a

4" opening dampered wall cap.

For more information on venting kits and accessories, please call 1-800-GE CARES.

R

Listed by

Underwriters

Laboratories

For answers to your Monogram, ® GE Profile ™

GE ® appliance questions, visit our website at or

GEAppliances.com or call

GE Answer Center ® service, 800.626.2000.

GE Appliances

DCCD330GDKC/WC – GE ® Super Plus 7.0 Cu. Ft. Capacity Coin-Operated Gas Dryer

Features and Benefits

• Auto Dry – Uses thermostats to monitor air temperature and reduce fabric wear.

• Pushbutton Controls – Simplifies cycle selection.

• LED Readout – Provides accurate wash times, from fill to finish.

• Painted Drum – Painted drum coated with a rustproof finish to stand up to heavy use.

• Three Heat Selections – Offers enhanced drying performance and fabric care.

• Three Dry Cycles – Offer quick, easy options for drying and caring for clothes.

• Reverse-A-Door – Offers added installation flexibility.

• Model DCCD330GDWC – White

• Model DCCD330GDKC – Bisque

Specification Created 5/03

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement