- No category
advertisement
▼
Scroll to page 2
of 7
INSTRUCTION MANUAL Plasma Center Channel Speaker Shelf (PAC-302) The Plasma Center Channel Speaker Shelf (PAC-302) can be used with the PAC-300 Side Speaker Adapter for a complete speaker installation with Chief mounts or attached separately to hold a single center channel speaker. The PAC-302 fits Chief’s patented Q-Latch mounting system for easy installation and provides width and height adjustment for different size speakers. The PAC-302 has five inches of height adjustment and adds ten pounds to the installation. The shelf is designed for below display installation only and the combined weight of the shelf, speakers and display must not exceed the weight capacity of the mount. BEFORE YOU BEGIN • CAUTION: To prevent damage to the PAC-302, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install or operate the unit. Pay particular attention to the “Important Precautions” on Page 1. • The maximum weight to be installed on the PAC-302 is limited by the weight specification of the mount. • If you have any questions about this assembly, contact Chief Manufacturing at 1-800-582-6480. CHIEF MANUFACTURING INC. 1-800-582-6480 952-894-6280 FAX 952-894-6918 8401 EAGLE CREEK PARKWAY, STE. 700 SAVAGE, MINNESOTA 55378 USA PART NO. 8800-000041 (Rev. B) ©2004 Chief Manufacturing www.chiefmfg.com Printed in USA 06-04 Instruction Manual PAC-302 IMPORTANT WARNINGS and CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. • WARNING: The maximum weight to be installed on the PAC-302 is limited to the weight specification of your mount. • CAUTION: Inspect the unit for shipping damage. TOOLS REQUIRED FOR INSTALLATION • Phillips screwdriver • 3/8” and 7/16” wrench • Socket set with extension • Allen wrench set NOTE: Other tools may be required depending on the method of installation. CONTENTS INSPECT PARTS BEFORE ASSEMBLY ..... 2 Inspect The Mount ...................................... 2 ASSEMBLE MOUNT .................................... 4 1 Instruction Manual PAC-302 INSPECT PARTS BEFORE ASSEMBLY Inspect The Mount 1. Carefully inspect the mount for shipping damage. If any damage is apparent, call your carrier claims agent and do not continue with the assembly procedure until the carrier has reviewed the damage. Read all assembly instructions before starting assembly. NOTE: 2. Carefully inspect the Plasma Center Channel Speaker Shelf (PAC-302) components for damage (See Figure 1). Item # 10. Mounting Mount Button Support (Left) 20. Mounting Mount Button Support (Right) 30. Upright (Left) 40. Upright (Right) 50. Height Adjustment Assembly 60. Shelf 70. Shelf Support (Left) 80. Shelf Support (Right) 90. Nylock Lock Nut, Short, 10-24 (Qty. 5) 2 Item # 100. Vinyl Cap, Black (Qty. 2) 110. Latching Flag 120. Phillips Undercut Machine Screw 10-24 X 1/2” 130. Nylon Spacer 140. 1/8” Hex Key 150. Mounting Button (Qty. 4) 160. Button Head Cap Screw 1/4-20X1/2” (Qty. 12) 170. Button Head Cap Screw 10-24X7/8” (Qty. 4) 180. Nylock Lock Nut 1/4-20 (Qty. 4) Instruction Manual PAC-302 20 10 30 7060 8090 50 100 110 120 40 90 130 Figure 1. Plasma Center Channel Speaker Shelf 3 Instruction Manual PAC-302 ASSEMBLE MOUNT NOTE: Numbers in ( ) refer to parts shown in Figure 1. Assemble mount as follows: 1. Attach two mounting buttons (150) to left speaker mount button support (10) and right speaker mount button support (20) using four 10-24X7/8” button head cap screws (170) and four Nylock nuts (170) (see Figure 1, Figure 2, and Figure 3). Button Support 2. Install the latching flag (110) using the 10-24X1/2” Phillips undercut screw (120), Nylon spacer (130) and 10-24 Nylock nut (90) (see Figure 4). 3. Install left upright (30) on left speaker mount button support (10) using two 1/4-20X1/2” button head cap screws (160) (see Figure 5). 4. Install right upright (40) on right speaker mount button support (20) using two 1/4-20X1/2” button head cap screws (160) (see Figure 5). 5. Install height adjustment assembly (50) on left upright (30), with left speaker mount button support attached, using two 1/4-20X1/2” button head cap screws (160) (see Figure 5). 6. Install height adjustment assembly (50) on right upright (40), with left speaker mount button support attached, using two 1/4-20X1/2” button head cap crews (160) (see Figure 5). Latching Flag Mounting Buttons Figure 2. Mounting Button Location Button Support 10-24X7/8” Button Head Cap Screw Mounting Button 10-24 Nylock Nut Figure 3. Mounting Button Attachment 10-24 Nylock Nut Nylon Spacer 10-24X1/2” Phillips Undercut Screw Figure 4. Install Latching Flag Figure 5. Install Uprights 4 Instruction Manual PAC-302 8. Install black Vinyl caps (100) on left shelf support (30) and right shelf support (40) (see Figure 6). 9. Install left shelf support (30) on shelf (60) and secure using two 1/4-20 Nylock nuts (180) (see Figure 6). 10. Install right shelf support (40) on shelf (60) and secure using two 1/4-20 Nylock nuts (180) (see Figure 6). 11. Install shelf (60) between height adjustment assemblies and secure using four 1/4-20X1/2” button head cap screws (160) (see Figure 6). Figure 6. Install Shelf Components 5 Instruction Manual 6 PAC-302
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project