Shure Performance Gear PG88, PG4, Performance Gear PG30, Performance Gear PG185, Performance Gear PG1, Performance Gear PG2, PS20, PS20E, PS20UK, PS20J, PS20CHN, PS20AZ, PS20K User manual

TE
MU
L
NNE
CHA
5 If you haven’t installed the
Startup
System Components
english
Follow these simple steps to check for interference and to
set your receiver and transmitter to the same channel.
battery, do it now and leave the
cover off.
Features
6
Busy Indicator
6 Turn ON the handheld or
or bodypack.
te
ready
audio
channel
ready
channel
PG88 Dual Wireless Receiver
m
Changing Channels
a
ch
The channel display should
illuminate.
PG4 Wireless
Receiver
l
e
nn
channel
Internal Anten
CHANNEL
audio
The channel display should
illuminate.
Diversity Antenna System
PG4
ready
Accessing Gain Switch
Multiple gain settings are available on the PG1 and PG2 transmitters.
To change gain settings, see below.
Press and hold the channel
button until the display starts
flashing.
2 Plug in the power supply.
audio
te
mu
ute
If left on, it will create a false
busy indicator.
To unlock controls: Press and hold Power/Mute button down until
Power/Mute LED flashes red and green.
If this occurs, change the
channel.
bodypack transmitter by
pressing the power button.
mu
audio
To lock controls: Turn transmitter off. Remove Battery Cover. Press
and hold Channel Button. Press and release Power/Mute button.
Power/Mute LED will flash red and green.
When selecting channels,
a flashing dash indicates
interference from television
broadcasts, electronic devices
or other wireless systems.
PS20
Power Supply
1 Turn OFF the microphone
Locking and Unlocking Transmitter Controls
Lock system controls to prevent accidental muting.
ready
While the display is flashing,
press the channel button.
l
ne
an
ch
It turns off after ten seconds to
conserve battery.
an
ch
channel
te
mu
The channel is active once
the display stops flashing.
l
ne
There is no power switch.
PG1
Bodypack
Transmitter
PG2 Handheld
Transmitter
0dB For instrument or quiet to normal vocal performance (default).
–10dB Use if audio is distorted due to high vocal or instrument levels.
mic Use for headworn or lavalier microphones (PG1 only).
el
nn
a
ch
7 Check to see that the
3 Press and hold down the
channel button until the
display begins flashing.
transmitter and the receiver
display the same channel.
Internal Anten
audio
audio
ready
ready
Wearing the Bodypack Transmitter
Receiver and transmitter
channels should match.
Internal Antenna Diversity
channel
audio
channel
Internal Antenna Diversity
ready
Clip the transmitter to belt or
guitar strap as shown.
channel
te
mu
Make sure the antenna is
unobstructed.
mu
te
l
cha
to stop flashing.
Internal Diver
Testing Audio
The ready LED on the receiver
should be illuminated.
audio
ready
channel
ready
Talk or sing into the
microphone or play
instrument.
channel
The audio LED on the
receiver should flicker green
or amber, if red, adjust the
Gain Switch.
8 Replace battery cover.
Printed in U.S.A.
Changing Battery
Expected life
a al
9 volt
alkaline battery is approximately 8 hours.When the
Infor
tern
Dive
r
Power/Mute LED glows red, the battery should be replaced immediately.
Internal Diversity Antenna Syste
audio
PG30
Headworn Mic
l
nne
4 Wait for the channel display
te
mu
©2006, Shure Incorporated
27EN8865 (Rev. 2)
hassle-free setup for worry-free
performance.
Performance Gear Wireless
systems are available in a
variety of configurations for
handheld, guitar, headset, and
presentation applications.
nne
C
ongratulations on
purchasing your Shure
Performance Gear Wireless
system. Shure professional
audio products deliver
legendary sound quality,
stage-proven durability and
If you see the Busy
Indicator (a flashing dash)
change the channel.
cha
PG185
Lavalier Mic
D"MIC
audio
ready
channel
l
nne
cha
pgw_en.indd 1
5/31/2006 9:05:51 AM
Issue
LED Status
Solution
No sound or
faint sound
Transmitter Power/
Mute LED on,
receiver LEDs on
• Perform transmitter setup.
• Verify all sound system connections.
• Adjust transmitter gain.
Receiver Channel
Display off • Make sure AC adapter is securely
plugged into electrical outlet and into
POWER connector on rear panel of
receiver.
• Make sure AC electrical outlet works
and is supplying proper voltage.
LED Status
TRANSMITTER
LED COLOR
Green
System Components
Troubleshooting
Multiple System Setup
To set up multiple systems, repeat the previous steps for each transmitter and
receiver pair. Once transmitters have been set, leave them on. Be sure to set
each transmitter and receiver pair to a different channel. For information about
frequencies and compatibility, refer to channel guide.
Transmitter LED
glowing
or flashing red
STATUS
Ready
Amber
Mute on
Red
Battery low
Flashing Red on startup
Battery is dead
Flashing Green and Red
Controls locked
Flashing Amber and Red
Mute on, battery low
Distortion or unwanted noise bursts
INDICATES
Green
Normal signal strength
Amber
Strong signal
Red
Peak signal
READY DISPLAY COLOR
INDICATES
Green
System is ready
Sound level different from cabled
guitar or microphone, or when
using different guitars
Cannot turn
transmitter on
Transmitter LED
flashing red
All Systems
System
PG4 or PG88 Receiver
Internal Diversity Antenna System
One 9 volt battery
AC Power supply
• Remove nearby sources of RF
interference (CD players, computers,
cell phones, digital effects, in-ear
monitor systems, etc.)
• Select a new channel for both receiver
and transmitter.
• Reduce transmitter gain.
• Replace transmitter battery.
• If using multiple systems, change the
channel of one of the active systems.
User guide
Vocalist System
Microphone Head
PG2 handheld transmitter
Microphone clip
Instrument System
PG1 bodypack
transmitter
Transmitter LED off • Turn transmitter on.
• Make sure the +/– indicators on
battery match transmitter terminals.
• Insert fresh battery.
RECEIVER
AUDIO LED COLOR
• Replace transmitter battery.
Technical Specifications
4-pin mini connector (TA4F) to
1/4” connector cable
PG4 and PG88 Receiver
Working Range
75m (250 ft.) Note: actual range depends on RF signal absorption, reflection,
and interference.
Output Impedance
XLR connector: 200 Ω
Audio Channel Response
Minimum: 45 Hz.
Maximum: 15 kHz (overall system channel depends on
microphone element).
Audio Output Level Ref.
+/– 33 kHz deviation with
1 kHz tone
XLR connector (into 100K Ω load): –19 dBV, typical
1/4 inch connector (into 100K Ω load): –5 dBV, typical
Total Harmonic Distortion
0.5%, typical
Ref. +/– 33 kHz deviation, 1 kHz tone
Sensitivity
–105 dBm for 12 dB SINAD, typical
Dynamic Range
>100 dB A-weighted, typical
Image Rejection
>50 dB, typical
Dimensions
188 mm L x 103 mm W x 40 mm D (7.4 in. x 4.0 in. x 1.5 in.)
Dimensions - PG88
388 mm L x 116 mm W x 40 mm D (15.3 in. x 4 in. x 1.5 in.)
Weight
241 grams (8.5 oz)
Weight - PG88
429 grams (15.1 oz)
Housing
Molded ABS
Power Requirements
12–18 Vdc at 160 mA (PG4), 320mA (PG88), supplied by external
power supply
Operating Temperature
Range
–18°C (0°F) to +57°C (+135°F)
Note: battery characteristics may limit this range
Transmitter Audio Polarity
Positive pressure on microphone diaphragm (or positive voltage to tip of
WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3
of low impedance output) and the tip of the high impedance 1/4-inch output.
Lavalier and Headworn System
PG1 bodypack
transmitter
Microphone (choice of PG185, PG30)
Replacement Parts
PG1 Bodypack Transmitter
Audio Input Level
–10 dBV maximum at “mic” gain position
+10 dBV maximum at 0dB gain position
+20 dBV maximum at –10dB gain position
Gain Adjustment Range
30 dB
All Systems
Microphone Stand Adapter (PGX2)
WA371
Input Impedance
1mΩ
System-Specific
AC Adapter (120 VAC, 60 Hz)
PS20
RF Transmitter Output
10 mW typical (dependent on applicable country regulations)
AC Adapter (230 VAC, 50/60 Hz, Europlug)
PS20E
Dimensions
110 mm H x 64 mm W x 21 mm D (4.3 x 2.5 x 0.8 in.)
AC Adapter (230 VAC, 50/60 Hz, UK)
PS20UK
Weight
75 grams (2.6 oz.) without battery
AC Adapter (100 VAC, 50/60 Hz)
PS20J
Housing
Molded ABS
AC Adapter (220 VAC, 50 Hz, China)
PS20CHN
Power Requirements
One 9V alkaline or rechargeable battery
AC Adapter (230 VAC, 50 Hz,, Australia)
PS20AZ
Battery Life
>8 hours (alkaline)
AC Adapter (220 VAC, 60 Hz, Korea
PS20K
PG58 Head with Grille
RPW108
Belt Clip
44A8035
PG2 Handheld Transmitter
Universal Rack Tray
URT
Audio Input Level
4-pin mini connector (TA4F) to 1/4”
connector cable
WA302
+2 dBV maximum at –10dB position
–8 dBV maximum at 0dB position
Gain Adjustment Range
10dB
RF Transmitter Output
10 mW typical (dependent on applicable country regulations)
Dimensions
223.52 L x 53.34 Dia. (8.8 in. x 2.10 in.)
Weight
218 grams (7.7 oz.) without battery
Housing
Molded ABS handle and battery cup
Power Requirements
One 9V alkaline or rechargeable battery
Battery Life
>8 hours (alkaline)
• Adjust transmitter gain as necessary.
• Replace transmitter battery.
Optional
Technical Specifications cont’d
1/4 inch connector: 1kΩ
Patents
Patent numbers 6,597,301 and 6,296,565
Regulatory Information
Regulatory Information for North America, Europe, and Australia
PG1 & PG2 Transmitters: Certified to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”).
Certified by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616APG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN
300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking.
PG4 and PG88 Receiver: Authorized under Declaration of Conformity (DoC) provision of
0978
!
FCC Part 15. Certified under Industry Canada to RSS-123 (“IC: 616A-PG4”). This class B
digital apparatus complies with Canadian ICES-003. Meets the essential requirements of the
European R&TTE Directive 99/5/ EC (EN 301 489 Parts 1 & 9, EN 300 422 Parts 1 & 2) and
is eligible to carry the CE marking. Conforms to Australian EMC requirements and is eligible
for C-Tick marking.
NOTE: This equipment has been tested and found to comply with the limits for a Class
N108
Z540
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio channel energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
PS20 Series Power Supplies: Conform to Safety Standard IEC 60065.
PS20E and PS20UK are eligible to bear CE marking.
A ministerial license may be required to operate this equipment in certain areas. Consult
your national authority for possible requirements.
This radio equipment is intended for use in musical professional entertainment and similar
applications.
pgw_en.indd 2
Caution
Changes or modifications not expressly approved by Shure Incorporated for compliance
could void the user’s authority to operate the equipment. Operation of this device is subject
to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
5/31/2006 9:05:53 AM
">