Models

GP7145GB and GP7255AGB pump with gearbox

Triplex Ceramic

Plunger Pump

Operation Manual

Updated 10/07

Contents:

Installation and Safety Instructions

Pump Specifications (GP7145GB-2.4): page 2 page 3

Exploded View:

Parts List: page 4 page 5

Pump Specifications (GP7255AGB-2.4): page 6

Kits/Torque Specifications:

Maintenance Information:

Repair Instructions:

Troubleshooting Guide:

Dimensions:

Warranty Information page 7 page 7 pages 8-9 page 10 page 11 back page

INSTALLATION INSTRUCTIONS

Operation and Maintenance

Check oil level prior to starting and ensure trouble-free water supply.

Oil: Use only 2 gallons (7.5 liters) if ISO VG-220 synthetic gear oil. Initial change after 50 hours and then after every 200 operating hours. If used less than this, change once per year.

IMPORTANT! When operating in humid areas (or areas with large temperature fluctuations, the oil must be changed immediately (if condensate or frothy oil occurs in the gear box).

IMPORTANT! We recommend that both inlet ports be used in order to ensure cavitation-free operation and optimal suction conditions. If only one connection is use, a safety margin of 3 feet (1 meter) has to be added to the required NPSH.

IMPORTANT! The GP7145GB and GP7255GB pumps have a black arrow on the reduction gear, which shows the preferred direction of rotation. The pump can be delivered either with the gear on the left side or right side

(when facing the front of the pump), which eases planning assembled units with regard to the desired direction or rotation. In either case, the larger gear wheel must rotate towards the front-end of the pump.

IMPORTANT! The service life of the seals is maximized if a minimal amount of leakage is present. A few drops of water can drip from each plunger every minute. Leakage has to be examine every day. If the leakage becomes excessive (constant dripping), the plunger seals must be changed.

Safety Rules

The operating instructions must be read and adhered to before performing any work on the pump or complete assembled unit. No responsibility will be carried by us for damage to materials or persons caused by improper

handling of our pumps.

Access to the pump is not allowed by unauthorized personnel. As safety valve is to be installed in accordance with the guidelines for liquid spraying units, so that the admissible operating pressure cannot be exceeded by more than 10%.

Pumps operating without a safety valve as well as any excess in temperature or speed limits automatically voids the warranty. When the pump is in operating, the exposed shaft side, the driven shaft side and its coupling must be covered by a protective guard. The plunger area must also be covered by the protective plate (30). Do not step onto the protective plate (30 ) or put weight on it.

The preferred/optimal direction of rotation ensures that the oil is correctly splashed on the crosshead guides via the motion of the connecting rods, which is a particular advantage where continuous operation is involved.

Before carrying out any maintenance work to the pump or pump unit, the pressure in the discharge line and pump must be at zero. Close off the suction line. Disconnect fuses to ensure that the driving motor cannot accidently get switched on. Before starting the pump, make sure that the pump, the cooling system and all parts on the pressure side of the unit are vented and refilled with pressure at zero.

In order to prevent air or air/water-mixture being absorbed and cavitation occurring, the pump NPSHR (Net Positive

Suction Head Required) and water temperature must be adhered to.

The pump can also be run against the recommended direction of the rotation if operated periodically or at reduced pressure. If this is the case, the pump has to be run in this direction to smoothen the bearing areas. This is done by a one-time operation at zero pressure for at least

30 minutes; thereafter, the pressure must be slowly increased over the next hour to the desired maximum operating pressure. This should run-in the pump, but you should also check the oil temperature, which should not exceed 160 o F (71 o C).

Cavitation and/or compression of gases lead to uncontrollable pressure kicks, which can ruin the pump and unit parts and also be dangerous to the operator or anyone standing nearby.

The torque tension on the valve casing nuts (49A) is to be checked after approximately 200 hours. Please see page 7 for torque values.

Giant plunger pumps are suitable for pumping clean water and other non-aggressive or non abrasive media, which have a specific weight similar to water.

Before pumping other liquids (in particular, flammable, explosive and toxic media), the pump manufacturer must be consulted with regard to the resistance of the pump

NOTE: Contact Giant Industries for

Service School Information.

Phone: (419)-531-4600.

2

Specifications

Model GP7145GB -2.4

U.S. ............................... (Metric)

Volume (Continuous) .............................................................. 47.5 GPM ..................... (180 LPM)

Volume (Intermittent) ............................................................. 60 GPM* ...................... (227 LPM)*

Discharge Pressure ................................................................. 3000 PSI ....................... (207 bar)*

Speed (Continuous) ........................................................................................................ 750 RPM

Speed (Intermittent) ........................................................................................................ 947 RPM

Inlet Pressure (maximum) ...................................................... 145 PSI ......................... (10 bar)

Plunger Diameter .................................................................... 1.77” ............................. 45mm

Plunger Stroke ........................................................................ 2.0” ............................... 52mm

Crankshaft Diameter ............................................................... 1.9” ............................... 48mm

Key Width ............................................................................... 0.6” ............................... 14mm

Crankshaft Mounting ...................................................................................................... Either side

Shaft Rotation ................................................................................................................. See Instructions on page 2

Temperature of Pumped Fluids .............................................. Up to 140 o F .................. (60 o C)

Inlet Ports ........................................................................................................................ (2) 2-1/2" NPT

Discharge Ports ............................................................................................................... (2) 1-1/4" NPT

Weight ..................................................................................... 455 lbs. ......................... (206 kg)

Crankcase Oil Capacity .......................................................... 1.6 Gal. ......................... (6.0 liter)

Fluid End Material .......................................................................................................... Spheroidical Cast Iron

Consult the factory for special requirements that must be met if the pump is to operate beyond one or more of the limits specified above.

PULLEY INFORMATION

Pulley selection and pump speed are based on a 1725

RPM motor and "B" section belts. When selecting desired GPM, allow for a ±5% tolerance on pumps output due to variations in pulleys, belts and motors among manufacturers.

1.

Select GPM required, then select appropriate motor and pump pulley from the same line.

2.

The desired pressure is achieved by selecting the correct nozzle size that corresponds with the pump

GPM.

HORSEPOWER INFORMATION

Horsepower ratings shown are the power requirements for the pump. Gas engine power outputs must be approximately twice the pump power requirements shown above.

We recommend that a 1.1 service factor be specified when selecting an electric motor as the power source.

To compute specific pump horsepower requirements, use the following formula:

(GPH X PSI) / 1450 = HP

GP7145GB-2.4 PULLEY SELECTION & HORSEPOWER

REQUIREMENTS

Input RPM RPM GPM 800 PSI 1000 PSI 1500 PSI 2000 PSI 3000 PSI*

720 300 19.0

10.9

13.6

20.4

27.1

40.7

960

1200

1440

400

500

600

25.3

31.7

38.0

14.5

18.1

21.7

18.1

22.6

27.1

27.1

33.9

40.7

36.2

45.2

54.3

54.3

67.9

81.4

1800

1894

2273

750

789

947

47.5

50.0

60.0

27.1

28.6

34.3

33.9

35.7

42.9

50.9

53.6

64.3

67.9

71.4

85.7

101.8

107.1

128.6

* Intermittent Duty Only!

3

Exploded View - GP7145GB-2.4/GP7255AGB-2.4

4

PARTS LIST - GP7145GB-2.4/GP7255AGB-2.4

2

4

5

ITEM PART

1 05324

1A

1B

05313

01009

13000

07601

07602

8

9

10

11

12

07603

01009

22706

06725

07109

13

14

07182

07607

14A 05325

15 07608

36 07706

DESCRIPTION

Crankcase

Head for Oil Dipstick

O-Ring

Oil Filler Plug Assy.

Crankcase Cover

Gasket, Crankcase Cover

Oil Dip Stick

O-Ring, Dip Stick

Hexagon Screw

Spring Washer

Drain Plug

Gasket, Drain Plug

Bearing Cover

Flange for Gearbox

Radial Shaft Seal

15A 05326

15B 05327

16 07184

17

20

05328

07610

20A 07611

21 07612

22 13405

O-Ring

Hexagon Socket Screw

O-Ring

Gear Seal

Taper Roller Bearing

Fitting Disc (Shim)

Shaft Protector

Crankshaft

23

24

25

28

07614

13182

13183

13184

Key

Connecting Rod Assy.

Crosshead Assy.

Crosshead Pin

30 07619 Cover Plate

30A 07225-0100 Hexagon Screw

30B 13136 Grommet

30C 08280

30D 13154

31

32

33

07623

07624

07626

33A 07627

33B 07628

33C 07249

34 13137

36 06165

Disc

Cover Plate

Eye Bolt

Radial Shaft Seal

Seal Retainer

O-Ring

Circlip

Fitting Disc

Oil Scraper

Plunger Pipe Assy.

(36A-D), GP7145

Plunger Pipe Assy.

(36A-D), GP7255A

Plunger Connection

Plunger Pipe, GP7145

Plunger Pipe, GP7255A

Tension Screw, GP7145

36A 07667

36B 05157

36B 07666

36C 06166

36C 07664

36D 07665

38

38

06167

13155

38A 13156

38B 06258

38B 07721

39

39

06171

13157

39A 13290

Tension Screw, GP7255A

Copper Ring

Seal Case, GP7145

Seal Case, GP7255A

O-Ring for 38

O-Ring for 38, GP7145

O-Ring for 38, GP7255A

Seal Sleeve, GP7145

Seal Sleeve, GP7255A

Grooved Ring, GP7145

1

8

4

3

3

1

3

1

2

1-5

1

1

1

6

2

3

3

3

3

1

3

8

1

3

1

1

2

1

8

8

1

1

3

QTY.

1

1

1

1

1

1

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

ITEM PART

39A 07723

40

41

07797

13296

41

42

42

13158

13294

07711

43

43

45

49

13293

07712

13297

13159

49A 13160

50 07791

50A 13162

51 05274

51A 13165

DESCRIPTION

Grooved Ring, GP7255A

QTY.

3

Support Disc, GP7255 only 3

Support Ring, GP7145 3

Support Ring, GP7255A

V-Sleeve, GP7145

V-Sleeve, GP7255A

3

9

6

Pressure Ring, GP7145

Pressure Ring, GP7255A

Tension Spring, GP7145 only 3

Stud Bolt 8

Hexagon Nut

3

3

8

Valve Casing

Cylinder Stud

Valve Assembly (51A-51F) 6

Spacer Pipe 6

1

2

G4

G5

G6

G7

51B 07732-0100 Valve Spring

51C 05314 Valve Plate

51D 05136 Valve Seat

51E

51F

53

56

07653

13166

22610

13167

56A 07658

O-Ring

Support Ring

Plug

Valve Adaptor

O-Ring for 56, 58

56B 07635

56C 13166

56D 07653

57 13173

58 13170

59A 07661

60 12251

61

G1

G2

G3

05170

05344

05328

05329

05330

05331

05332

07008

05333

G8

G9

05334

05335

G10 05336

G11

G12

G13

G15

G16

13358

05337

05319

05338

05339

G17 05340

G18 13243

G19 05341

G20 05342

G21 05343

Support Ring for 56A, 58A 6

Support Ring

O-Ring

Tension Spring

Plug, M64 x 2

Copper Ring for 12

Plug, 1-1/4” NPT

Plug, 2-1/2” NPT

Fitting Key

Cogwheel

Tension Disc

Hexagon Screw

Pinion

Ball Bearing

Fitting Disc

Fitting Disc

Shaft Seal Ring

Fitting Key

Washer

Screw Plug

Copper Ring

3

2

2

1

1

2

1

1

1

3

1

1

3

6

Gearbox Assy, 2.4:1 (G1-G21) 1

Casing, Bottom

Casing, Top

Cylindrical Pin

Hexagon Screw

Washer

Hexagon Socket Screw

Spacer Ring

3

3

6

6

6

6

6

6

1

6

2

8

6

1

1

2

2

2

1

1

2

07662

05210

05211

Valve Tool (Not Shown)

Plunger Conversion Assy.

(36-45), GP7145

Plunger Conversion Assy.,

(36-45), GP7255A

1

1

1

5

Specifications

Model GP7255AGB-2.4

U.S. ............................... (Metric)

Volume (Continuous) .............................................................. 65.8 GPM ..................... (250 LPM)

Volume (Intermittent) ............................................................. 80 GPM* ...................... (303 LPM)*

Discharge Pressure (Continuous) ........................................... 1500 PSI ....................... (100 bar)

Discharge Pressure (Intermittent) ........................................... 2000 PSI ....................... (140 bar)*

Speed (Continuous) ........................................................................................................ 700 RPM

Speed (Intermittent) ........................................................................................................ 851 RPM

Inlet Pressure (maximum) ...................................................... 145 PSI ......................... (10 bar)

Plunger Diameter .................................................................... 2.17” ............................. 55mm

Plunger Stroke ........................................................................ 2.0” ............................... 52mm

Crankshaft Diameter ............................................................... 1.9” ............................... 48mm

Key Width ............................................................................... 0.6” ............................... 14mm

Crankshaft Mounting ...................................................................................................... Either side

Shaft Rotation ................................................................................................................. See Instructions on page 2

Temperature of Pumped Fluids .............................................. Up to 140 o F .................. (60 o C)

Inlet Ports ........................................................................................................................ (2) 2-1/2" NPT

Discharge Ports ............................................................................................................... (2) 1-1/4" NPT

Weight ..................................................................................... 455 lbs. ......................... (206 kg)

Crankcase Oil Capacity .......................................................... 1.6 Gal. ......................... (6.0 liter)

Fluid End Material .......................................................................................................... Spheroidical Cast Iron

Consult the factory for special requirements that must be met if the pump is to operate beyond one or more of the limits specified above.

PULLEY INFORMATION

Pulley selection and pump speed are based on a 1725

RPM motor and "B" section belts. When selecting desired GPM, allow for a ±5% tolerance on pumps output due to variations in pulleys, belts and motors among manufacturers.

1.

Select GPM required, then select appropriate motor and pump pulley from the same line.

2.

The desired pressure is achieved by selecting the correct nozzle size that corresponds with the pump

GPM.

HORSEPOWER INFORMATION

Horsepower ratings shown are the power requirements for the pump. Gas engine power outputs must be approximately twice the pump power requirements shown above.

We recommend that a 1.1 service factor be specified when selecting an electric motor as the power source.

To compute specific pump horsepower requirements, use the following formula:

(GPH X PSI) / 1450 = HP

GP7255AGB-2.4 PULLEY SELECTION & HORSEPOWER

REQUIREMENTS

Input RPM

1150

1274

1404

1531

1680

2042

RPM GPM 800 PSI 1000 PSI 1300 PSI 1500 PSI 2000 PSI *

479 45.0

531 49.9

585 55.0

25.7

28.5

31.4

638 60.0

700 65.8

34.3

37.6

851 80.0* 45.7

32.1

35.6

39.3

42.9

47.0

57.1

41.8

46.3

51.1

55.7

61.1

74.3

48.2

53.5

58.9

64.3

70.5

85.7

64.3

71.3

78.6

85.7

94.0

114.3

* Intermittent Duty Only!

6

Repair Kits - GP7145GB-2.4 and GP7255AGB-2.4

Plunger Packing Kit - GP7145GB-2.4

# 09603

Item

38A

38B

Part #

13156

06258

Description

O-Ring

O-Ring

39A

42

13290

13294

Grooved Ring

V-Sleeve

Qty.

3

3

3

9

Plunger Packing Kit - GP7255AGB-2.4

# 09220

Item

38A

38B

Part #

13156

07721

Description

O-Ring

O-Ring

39A

41

42

07723

13158

07711

Grooved Ring

Support Ring

V-Sleeve

Qty.

3

3

3

3

6

Valve Repair Kit

# 09604

Item Part #

51B

51C

51D

Description

07732-0100 Valve Spring

05314 Valve Plate

05136 Valve Seat

51E/56D 07653

51F/56C 13166

56A

56B

07658

07635

O-Ring

Support Ring

O-Ring

Support Ring

2

2

2

2

Qty.

1

1

1

Oil Seal Kit

# 09221

Item Part #

32

33A

07624

07627

Description Qty.

Radial Shaft Seal 3

O-Ring 3

GP7145GB-2.4 and GP7255AGB-2.4 Torque Specifications

Position Item# Description

24 13182 Connecting Rod Assembly

36C 06166/07664 Tension Screw

49A

58

13160

13170

Hexagon Nut

Plug

Torque Amount

30 ft.-lbs. (40 NM)

30ft.-lbs. (40 NM)

103 ft.-lbs. (140 NM)

107 ft-lbs (145 NM)

Preventative Maintenance Check-List & Recommended Spare Part List

Check

Oil Level / Quality

Oil Leaks

Water Leaks

Belts, Pulley

Plumbing

Daily Weekly 50hr Every Every Every

200 hr 1500 hr 3000hrs

Oil Change

Plunger Packing Kits(1 kit/Pump)

X

X

X

X

X

Recommended Spare Part

X X

X

Oil Seal Kit ( 1 kit/Pump

X

Valve Kit ( 1 kit/pump)

X

7

GP7145GB-2.4 and GP7255AGB-2.4 Repair Instructions

TO CHECK VALVES

Loosen plugs (58), take out tension spring (57) and then remove the complete valve assembly (51) with either a valve tool or an M16 hexagon screw. To remove the valve adapter (56) and tension spring (57), use a pullout tool size 5. To disassemble valve assembly, carefully hit the top of the valve plate (51C) with a metal dowel and press the valve seat (51E) out of the valve adapter (56). Check sealing surfaces and replace worn parts. Check O-rings and support rings. Tighten plugs (58) to 107 ft.-lbs. (145 NM).

TO CHECK SEALS AND PLUNGER PIPE

Loosen nuts (49A) and remove pump head (50). Separate the plunger connection (36A) from the crosshead (25) by means of two open-end wrenches (size 22mm and 27mm). Pull seal sleeves (39) out of their fittings in the crankcase (1). Take the seal case (38) out of the seal sleeve (39). Examine the plunger parts (36A-36D), seals (42 & 39A) and O-rings (38A & 38B). When replacing the plunger pipe

(36B), tighten tension screws (36C) to 30 ft. lbs. (40 NM). Replace worn parts; grease seals with Silicone before installing.

CAUTION: Don't loosen the 3 plunger connections (36A) before the valve casing has been removed otherwise the tension screw (36C) could hit against the valve adapter (56) when the pump is being turned. Seal life can be increased if the pre-tensioning allows for a little leakage.

This assists lubrication and keeps the seals cool. It is therefore not necessary to replace seals before the leakage becomes too heavy and causes output and operating pressure to drop.

MOUNTING VALVE CASING

Check O-rings (38A & 38B) on the seal case (38). Clean surfaces of seal sleeves in gear box and sealing surfaces of valve casing (50). Push the valve casing carefully on the O-rings of the seal case and centering studs (50A). Tighten nuts (49A) to 103 ft. lbs. (140 NM).

TO DISASSEMBLE GEAR

Take out plunger (36) and seal sleeves (39) as described above. Drain the oil. After removing the circlip ring (33B), lever out seal retainer (33) with a screw driver. Check seals (32 & 33A) and surfaces of crosshead (25) .

Important! Seal (32) must always be installed so that the seal-lip on the inside diameter faces the oil.

Possible axial float of the seal retainer (33) should be compensated with the shims (33C).

Remove the crankcase cover (4). Loosen inner hexagon screws on the connecting rods (24).

Note: Connecting rods are marked for identification. Do not twist connecting rod halves. Each connecting rod is to be reinstalled in the same position (and orientation) on the crankshaft journals.

Push the connecting rod halves as far into the crosshead guide as possible. Take out the bearing cover

(14).

8

GP7145GB-2.4 and GP7255AGB-2.4 Repair Instructions

TO DISMANTLE REDUCTION GEAR

Remove screws (G4). Using screwing two screws into the both thread bores, press off the gear cover

(G2). Remove screw (G11) and take off the spacer ring (G7) and tension disc (G10). Push the cogwheel

(G9) off the shaft by screwing two screws into both thread bores. Finally, take the crankshaft (22) out of the crankcase by tapping it towards the bearing cover side using a rubber hammer.

Check the surfaces of connecting rods (24), crankshaft (22) and crossheads (25). Check the surfaces of the crosshead guides in the crankcase for any unevenness.

Reassemble in reverse order. Regulate axial bearing clearance to a minimum of 0.1mm and a maximum

0.15mm by means of fitting discs (20A). Insert the crankshaft by passing it through on the bearing cover side. Press in the outer bearing ring (20). The crankshaft should turn easily and with little clearance.

Fit the bearing cover (14) and tighten screws (24) to 30 ft.-lbs. (40 NM).

Important! The connecting rod has to be able to slightly move sidewise at the crankshaft journal.

Heat the ball bearings (G13) before pressing them onto the pinion (G12). Slightly press the cogwheel

(G9) onto the crankshaft, so that the pinion (G12) together with the bearing (G13) can still be inserted.

When mounting, place the pinion (G12) onto the cogwheel so that they correctly interlock. Carefully tap the cogwheel and the pinion simultaneously onto the crankshaft and into the bearing seat.

Fit tension disc (G10), and spacer ring (G7) and tighten screw (G11) with Loctite.

Fit seal (17) on to the cylindrical pins (G3).

Push the gear cover (G2) carefully on to the bearing (G13). make sure the radial shaft seal (G17) does not get damaged during fitting on to the pinion.

Important! Before putting into operation again, turn the reduction gear shaft by hand at least four full turns to make sure that the gear is correctly aligned.

9

PUMP SYSTEM MALFUNCTIONS

MALFUNCTION CAUSE REMEDY

The Pressure and/ or the Delivery Drops

Worn packing seals Replace packing seals

Broken valve springs

Belt slippage

Worn or Damaged nozzle

Fouled discharge valve

Replace springs

Tighten or Replace belt

Replace nozzle

Clean valve assembly

Worn or Plugged relief valve on pump Clean, Reset, and Replace worn parts

Cavitations Check suction lines on inlet of pump for restrictions

Unloader Check for proper operation

Water in Crankcase High Humidity

Worn Seals

Reduce oil change intervals

Replace seals

Noisy Operating Worn bearings

Cavitation

Rough/Pulsating Worn packing

Operation with

Pressure Drop

Inlet restriction

Replace bearings, Refill crankcase oil with recommended lubricant

Check inlet lines for restrictions and/or proper sizing

Replace packing

Accumulator pressure

Unloader

Cavitation

Check system for stoppage air leaks, correctly sized inlet plumbing to pump

Recharge/Replace accumulator

Check for proper operation

Check inlet lines for restrictions and/or proper size

Re-size discharge plumbing to flow rate of pump

Pump Pressure as

Drop at gun Rated,

Pressure

Leakage

Restricted discharge plumbing

Excessive Worn plungers

Worn packing/seals

Excessive vacuum

Cracked plungers

Inlet pressure too high

Replace plungers

Adjust or Replace packing seals

Reduce suction vacuum

Replace plungers

Reduce inlet pressure

High Crankcase

Temperature

Wrong Grade of Oil Giant oil is recommended

Improper amount of oil in crankcase Adjust oil level to proper amount

10

Dimensions - GP7145GB-2.4 and GP7255AGB-2.4 - Inches (mm)

11

GIANT INDUSTRIES LIMITED WARRANTY

Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free from defects in workmanship and material as follows:

1.

For portable pressure washers and self-service car wash applications, the discharge manifolds will never fail, period. If they ever fail, we will replace them free of charge. Our other pump parts, used in portable pressure washers and in car wash applications, are warranted for five years from the dateof shipment for all pumps used in NON-SALINE, clean water applications.

2.

One (1) year from the date of shipment for all other Giant industrial and consumer pumps.

3.

Six (6) months from the date of shipment for all rebuilt pumps.

4.

Ninety (90) days from the date of shipment for all Giant accessories.

This warranty is limited to repair or replacement of pumps and accessories of which the manufacturer’s evaluation shows were defective at the time of shipment by the manufacturer. The following items are NOT covered or will void the warranty:

1.

Defects caused by negligence or fault of the buyer or third party.

2.

Normal wear and tear to standard wear parts.

3.

Use of repair parts other than those manufactured or authorized by

Giant.

4.

Improper use of the product as a component part.

5.

Changes or modifications made by the customer or third party.

6.

The operation of pumps and or accessories exceeding the specifications set forth in the Operations Manuals provided by Giant Industries, Inc.

Liability under this warranty is on all non-wear parts and limited to the replacement or repair of those products returned freight prepaid to Giant Industries which are deemed to be defective due to workmanship or failure of material. A Returned

Goods Authorization (R.G.A.) number and completed warranty evaluation form is required prior to the return to Giant Industries of all products under warranty consideration. Call (419)-531-4600 or fax (419)-531-6836 to obtain an R.G.A.

number.

Repair or replacement of defective products as provided is the sole and exclusive remedy provided hereunder and the MANUFACTURER SHALL NOT BE LIABLE

FOR FURTHER LOSS, DAMAGES, OR EXPENSES, INCLUDING INCIDEN-

TAL AND CONSEQUENTIAL DAMAGES DIRECTLY OR INDIRECTLY ARIS-

ING FROM THE SALE OR USE OF THIS PRODUCT.

THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER

WARRANTIES OR REPRESENTATION, EXPRESS OR IMPLIED, INCLUD-

ING WITHOUT LIMITATION ANY WARRANTIES OR MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH WARRANTIES

ARE HEREBY DISCLAIMED AND EXCLUDED BY THE MANUFACTURER.

GIANT INDUSTRIES, INC.

900 N. Westwood Ave.

P.O. Box 3187

Toledo, Ohio 43607

(419) 531-4600

FAX (419) 531-6836



Copyright 2007 Giant Industries, Inc.

www.giantpumps.com

10/07 GP7145GB_GP7255AGB.PMD