Gillette | NETLINK E340 | User's Manual | Gillette NETLINK E340 User's Manual

150
140
power
off
Type 5684
5684425_NE150_China_S1.indd 1
13.03.2007 9:25:31 Uhr
4
English
7
Braun GmbH
Frankfurter Straße 145
61476 Kronberg/Germany
5-684-425/00/III-07
China/GB
5684425_NE150_China_S2.indd 1
13.03.2007 9:26:09 Uhr
on
power
off
off
of
f
1
power
90°
2
4 (150 only)
3
A
power
5
off
washable
6
B
7
8
9
power
power
power
power
off
oil
8h
5684425_NE150_China_S3.indd 1
13.03.2007 9:27:42 Uhr
4
5684425_NE150_China.indd 4
15.03.2007 13:39:57 Uhr
5
5684425_NE150_China.indd 5
15.03.2007 13:40:00 Uhr
6
5684425_NE150_China.indd 6
15.03.2007 13:40:00 Uhr
English
Our products are designed to meet
the highest standards of quality,
functionality and design. We hope you
enjoy your new Gillette Shaver.
Warning
Your shaver is provided with a special
cord set, which has an integrated
Safety Extra Low Voltage power
supply. Do not exchange or tamper
with any part of it, otherwise there is
risk of electric shock.
Description
1
2
3
4
5
6
7
8
9
Foil protection cap
Shaver foil
Cutter block
Long hair trimmer (model 150 only)
On switch («power»)
«off» switch
Power LED
Shaver power socket
Special cord set
Charging
The best environmental temperature
for charging is between 5 °C and
35 °C. Do not expose the shaver to
temperatures higher than 50°C for
extended periods of time.
• Using the special cord set (9),
connect the shaver to an electrical
outlet with the motor switched off.
• To make sure that the shaver is
switched off, press the «off» switch
(6) before you start charging.
• When charging for the first time,
leave the shaver to charge
continuously for 16 hours.
• The power LED (7) indicates that the
shaver is connected to an electrical
outlet.
• Subsequent charges will take about
8 hours.
• A full charge provides up to 20
minutes of cordless shaving time.
This may vary according to your
beard growth.
• Maximum battery capacity will only
be reached after several charging/
discharging cycles.
Shaving
Press the on switch (5) to operate the
shaver.
Model 150 only: To trim sideburns,
moustache or beard, slide the long hair
trimmer (4) upwards.
Tips for the perfect shave
For best shaving results, we
recommend you to follow 3 simple
steps:
1. Always shave before washing
your face.
2. At all times, hold the shaver at
right angles (90°) to your skin.
3. Stretch your skin and shave
against the direction of your
beard growth.
Cleaning
The shaver head is suitable for
cleaning under running tap
water.
Warning: Detach the shaver
from the power supply before
cleaning the shaver head in
water.
7
5684425_NE150_China.indd 7
15.03.2007 13:40:01 Uhr
Regular cleaning ensures better
shaving performance. Rinsing the
shaving head under running water after
each shave is an easy and fast way to
keep it clean (A):
• Switch the shaver on and rinse the
shaver head under hot running water.
You may use liquid soap without
abrasive substances. Rinse off all
foam and let the shaver run for a few
more seconds.
• Next, switch off the shaver, remove
the shaver foil (2) and cutter block
(3). Then leave the disassembled
shaving parts to dry.
• If you regularly clean the shaver
under water, then once a week apply
a drop of light machine oil onto the
long hair trimmer and shaver foil.
Alternatively, you may clean the shaver
using the brush provided (B):
• Switch off the shaver. Remove the
shaver foil and tap it out on a flat
surface.
• Using the brush, clean the cutter
block and the inner area of the
shaver head. However, do not clean
the shaver foil with the brush as this
will damage the foil.
Environmental notice
This appliance contains
rechargeable batteries. In the
interest of protecting the
environment, please do not
dispose of the product in
household waste at the end of its
useful life. Disposal can take place at a
Braun Service Centre or at appropriate
collection points provided in your
country.
Subject to change without notice.
This product conforms to
the European Directives EMC
89/336/EEC and Low Voltage
2006/95/EC.
For electric specifications, see printing
on the special cord set.
Keeping your shaver in top
shape
Replacing the shaver foil and cutter
block
To maintain 100% shaving
performance, replace the shaver foil (2)
and cutter block (3) at least every
18 months or when worn. Change both
parts at the same time for a closer
shave with less skin irritation.
(Shaver foil and cutter block: 11B)
8
5684425_NE150_China.indd 8
15.03.2007 13:40:02 Uhr
Download PDF