CX-One FA Integrated Tool Package Promotional Brochure

CX-One FA Integrated Tool Package Promotional Brochure
N E W
FA Integrated Tool Package
One software for your complete machine
Easy, Intuitive Programming Software
Structured Text for Simple programming
Easy Input - Easy Designing - Easy Validation
Further Advanced Integrated Tool Package CX-One Version 4
ST programming for further easy and
simple programing and configuration
of PLC systems
The CX-One is an integrated package of Support Software including setup applications for networks, PTs, Servo
Drives, Inverters, and Temperature Controllers as well as programming software of PLCs.
New Feature 1
Symbol in data structures
Data structures, the timer data type,
e,
and the counter data type can be
used in ST and SFC programs.
Motor 1
Operation command
Acceleration time
Deceleration time
Data Structures
Data Structures
A data structure is a user-defined data type that groups various data together.
getther.
By grouping the data, the large volumes of data handled by a program are
sierr.
made easier to understand and can be registered or changed much easier.
Motor 2
Operation command
Operation command
Frequency command
Frequency command
Acceleration time
Acceleration time
Deceleration time
Deceleration time
Timer and Counter Data Types
Timer and counter data types can now be treated as symbols in
ST and SFC programs. You can thus use them as symbols in
arrays to build programs that can be easily reused.
New Feature 2
Quickly adjust the gain using a wizard.
The autotuning feature provided with the CX-Drive makes it easy to adjust the Servo Drive gain.
You can use a wizard to complete gain adjustment in approximately five minutes or less per axis
simply by selecting the machine configuration and entering the target set time.
Autotuning
Gain adjusted in 5 minutes per axis.
Machine Configuration
Although previously the machine configuration was set using parameters,
it can now be selected from ball screws, turntables, belts, and other devices.
Automatic Adjustment
Setting for automatic adjustment and conditions after completing
automatic adjustment.
Autotuning
Implement auto-tuning until reaching to a target value.
Stabilization time, overshooting amount and efective load rate can be monitored.
Autotuning Completed
After completing autotuning, the results can be checked
using the data tracing.
2
Symbol in data structures
Motor
Symbol in data structures
Motor 3
Operation command
Frequency command
Acceleration time
Deceleration time
Data can be easily rreused as on
one
ne entity
entity.
y.
Frequency command
CX-One
Ver.4
Support for More Hardware Products
CJ2M Pulse I/O Modules
Easy Programming
You can also easily monitor Pulse I/O Module settings,
output frequencies (on data trace diagrams), and other values.
Note: A Pulse I/O Module must be mounted for CJ2M CPU Units
with unit version2.0 or later.
Reusable Designs
Position Control
Support for New Operating System
Network
Windows 64-bit Editions
In addition to the 32-bit editions of Windows Vista and 7, the 64-bit editions are now also supported.
Note: The Windows XP 64-bit edition is not supported.
Debugging
CX-One Tools
Network Settings
Programming/Simulation
Component Tools
Programmable Terminal
Screen Creation
Motion Control
PLC-based Process Control
Serial
FA Communications Software
SYSMAC CJ1
Loop Controller
Network between PLCs
Smart Slice
Remote I/O Terminals
Network Settings
Ordering Information
Remote I/O Terminals
Creation of
Protocol
Macros
Online Web Services
Generic External
Devices
Temperature Controllers
Temperature
Controller Settings
Servomotor
Servomotor
CX-One Lite
Inverter
Inverter
Servo/Inverter Settings
Windows is a registered trademark of the Microsoft Corporation. DeviceNet, DeviceNet Safety, CompoNet, and EtherNet/IP are registered trademarks of the ODVA.
MECHATROLINK-II is a registered trademark of the MECHATROLINK Members Association.Other company names and product names are the trademarks or registered
trademarks of the respective companies.
3
Easy Programming
Steps Required to
Input Ladder Diagrams
Reduced 50%
NEW
Note: In comparison to
CX-Programmer version 8.
Patent Pending
Input without Wasted Effort !
Use Mnemonics to Input Instructions Directly or Use 1-key Inputs
A Smart Input Function greatly reduces
the work required to input programs
A new method is now available that lets you input instructions directly using mnemonics.
Other functions include automatic addresses for operands, including input bits and output bits, automatic insertion of connecting
lines for output and application instructions, and other smart input functions that greatly reduce the work required to input ladder diagrams.
*This function is supported only for ladder diagrams.
Instruction and Address Input Assistance
When you begin typing an instruction from the keyboard while in the Ladder Editor Window, suggested instructions are displayed.
All you have to do is select the instruction from the list for easy input even if you do not remember the entire mnemonic.
Suggested instructions displayed
Automatic Insertion of Connecting Lines
When an output or application instruction is input, the required connecting line is inserted automatically starting at the cursor location.
This greatly simplifies the work required to insert lines.
A vertical
connecting
line is created
upward from
the cursor
location
Address Incremental Copy
To create the same group of ladder instructions more than once, the address incremental copy function can be used to reuse the instructions
simply by inputting an address offset.Also, address offsets can be set individually and I/O comments can be created automatically.
4
CX-One
Ver.4.0
Easy Programming
Auxiliary Bit Input from Lists
Clock Pulse Flags, Condition Flags, and other special bits in the Auxiliary can be selected from lists, eliminating the need to remember addresses.
Reusable Designs
The more frequently used flags
appear at the top
Position Control
Network
Address Incrementing
Debugging
The address of the next operand, including input bits and output bits, is incremented by one and displayed as the default.
This enables easily inputting consecutive addresses.
Component Tools
The previously input address (CIO 0.00) is automatically
incremented by one and displayed as the default operand.
FA Communications Software
Online Web Services
Quick-key Input of Both Instruction and Operands, and Consecutive Input of Instructions
When an instruction is displayed with a default operand, just press the Shift + Enter Keys to confirm input of both the instruction and operand.
To input the same instruction consecutively, just press the Ctrl + Enter Keys.
We've eliminated the number of steps for key operations wherever possible.
Ordering Information
CX-One Lite
Quick-key Input of Both Instruction and Operands
Consecutive Input of Instructions
5
Easy Programming
CX-Programmer
Easily program numeric calculations and text string operations with structured text.
Structured Text for Simple and
easy-to-understand Programming
Structured Text (ST)
Numeric calculations, conditional branching, and text string processing, all of which can be difficult with ladder diagrams,
can be easily programmed using ST.
Calculating the Length and Angle from X,Y Coordinates Using Numeric Calculations and Conditional Branching
Ladder Diagram
Structured Text
•Work memory is required to temporarily hold the
•Work memory, which is required for the ladder diagram,
calculation results.
•The control data for each instruction must be
understood and suitable numeric values must be set.
•The calculations cannot be written as formulas.
is not required.
•The calculations can be written in numeric form.
•It is not necessary to understand the special ladder instructions
of each manufacturer or the control data for the instructions.
Collecting Date Information from the PLC Using Text String Operations
Ladder Diagram
Structured Text
•Work memory is required to join the text strings.
•Work memory, which is required for the ladder diagram, is not required.
•Text string processing is complex and difficult to
•Text string processing can be handled in a high-level programming language.
understand.
6
Reusable Designs
CX-One
Ver.4.0
Easy Programming
Data Structures, Timer Data Type, and Counter Data Type
Reusable Designs
Support for data structures, a timer data type, and a
counter data type makes reusing program designs much easier
Applicable Models
: CJ2
CJ2
Data Structures
A data structure is a user-defined data type that groups various data together. By grouping the data, large volumes of
data handled by a program are made easier to understand and can be registered or changed much easier.
Position Control
Data can be easily reused as one entity.
If the same pattern is repeated
in the data, you can define a data
structure to enable easily reusing
the data in programming.
Motor 1
Motor
Operation command
Frequency command
Acceleration time
Frequency command
Motor 2
Deceleration time
Acceleration time
Deceleration time
Network
Operation command
Operation command
Frequency command
Acceleration time
Deceleration time
Debugging
Structure definition
The same data structure is used.
This group of symbolscan be easily reused.
Component Tools
Data can be easily changed.
Motor
Motor 1
Operation command
Operation command
Frequency command
Acceleration time
Deceleration time
For example, you can delete
the "frequency command"
member of the data structures.
Frrequeency com
mmand
Acceleration time
Deceleration time
Online Web Services
Structure definition
FA Communications Software
Even if there are changes to the
data, the definition of the data
structures can be modified to
automatically change the data
structures symbols in the
symbol table as well.
The change is automatically applied to
the data structures symbols as well.
Ordering Information
Timer and Counter Data Types
The timer and counter data types can now be used in ST. This enables using timers in ST to perform wait processing.
Example of Processing after a Specified Period of Time Elapses
CX-One Lite
TIMX(In1, My Timer, 50);
100-MS
TIMER
timer set value
timer address
execution condition
The addition is executed when the Completion Flag (CF)
of MyTimer turns ON in 5 seconds.
7
Position Control
Improved Functionality for Position Control
Preliminary Verification of Memory Operation
for Position Control
Applicable Models : CJ1W-NC
4/NC
Use Memory Operation Previews for Smoother Startup
Verifying operation before transferring the memory operation data to the Unit enables smoother startup and reduces the work involved in system verification.
Display graphs of positions or
speeds against time.
Easily compare results to data tables using
sequence numbers displayed in the graph.
Display Axis Movement Patterns for Two Interpolated Axes or for All Axes
You can verify movements by axis for each task. (Up to four axes can be displayed for each task.) Just click to switch the frame of reference for
confirming operating patterns between one/two-axis interpolation, all axes, and pulse output instructions.
Displaying Two Interpolated Axes
Displaying the
movement for two-axis
interpolation enables
visually verifying the
interpolated operation,
which is very difficult to
imagine with table data.
A pointer moves on the
movement pattern when
it is replayed.
This enables preliminary
verification of
movements.
8
Displaying All Axes
Displaying timing changes
side by side for changes in
position or speed over time for
all of the axes lets you verify
the timing of operations.
CX-One
Ver.4.0
Easy Programming
Position Control Unit and Communications Setup Integrated into the CX-Programmer
Easily Achieve Position Control without
Wading Through User Manuals
Applicable Models : CJ1W-NC 81
Reusable Designs
Setup the Position Control Units and Servo Drives from One Connection
Just connect the computer to a CPU Unit port to set up the Position Control Units with EtherCAT interface and EtherCAT communications.
You can also directly start the CX-Drive Support Software to set the Servo Drives connected to the Position Control Units.
Position Control
Position Control Units
with EtherCAT interface
Network
Debugging
Component Tools
AC Sarvo driver
R88D-KN -ECT
FA Communications Software
Automatic Network Setup
The communications parameters for Position Control Units with EtherCAT interface can be set simply by selecting a menu command.
Online Web Services
Ordering Information
CX-One Lite
After automatically setting the network,
you can immediately transfer the parameters
for the Position Control Unit.
9
Network
NEW
USB and EtherNet/IP Ports are available for SYSMAC CJ2 CPU Units
Easier Connection to PLCs
Applicable Models : CJ2
Easy connection with USB
A standard USB cable can be easily connected to the USB port on the front of the CPU Unit.
Standard USB cable
Standard-feature
USB port
CX-One
( Example:CX-Programmer)
Easy Connection with EtherNet /IP
Easy connection by specifying the computer LAN (Ethernet) port and IP address only.
*CJ2(built-in EtherNet/IP) CPU Units only.
EtherNet/IP
CX-One
( Example:CX-Programmer)
HUB
192.168.250.13
192.168.250.14
192.168.250.15
Prevent Connection Errors by Verifying PLC Names
The CJ2 CPU Unit can record a PLC name. Errors in transfers can be prevented ahead of time because
the PLC name can be compared with what is in the project file when connecting online.
Online connection
HUB
Browse and Connect from
the EtherNet/IP Connection List
PLC name
PLC name
PLC name
Equipment_A
Equipment_B
Equipment_C
Select a PLC from the list to connect to it.
Even if the IP address is unknown, you can browse a
list of PLCs connected to the EtherNet/IP and select
one to connect to it. With this, remote debugging
and maintenance can be conducted smoothly on site.
*CJ2(built-in EtherNet/IP) CPU Units only.
10
The PLCs connected to the EtherNet/IP network
are automatically detected.
Simply select from the list of PLCs and connect.
CX-One
Ver.4.0
NEW
Easy Setting of Tag Data Links for EtherNet/IP
*CJ2(built-in EtherNet/IP) CPU Units only.
Reusable Designs
In addition to creating data links with the EtherNet/IP Datalink Tool using I/O memory addresses, you can also use network symbols for tags to
easily create the data links.
With EtherNet/IP, high-speed, high-volume data links can be created with different cycle specifications for each applications, regardless of the number of nodes.
Easy Programming
Integration of Network Construction and Parameter Settings
Position Control
Network
Remote I/O Terminals
Smarts Slice
Component Tools
A wizard can be used to easily set the tag data
links for Ethernet/IP by importing the network
symbols for tags from the CX-Programmer.
Remote I/O Terminals
Debugging
EtherNet/IP Tag
Data Link Setting Wizard
Temperature Controllers
FA Communications Software
Ordering Information
EtherNet/IP data links can be easily
created by setting I/O memory addresses
in data link tables.
Online Web Services
EtherNet/IP
Datalink Tool
CX-One Lite
11
Debugging
Comprehensive Debugging for Networks
Time Required for Onsite Startup and
Debugging Has Been Significantly Reduced
With CX-One version 3.0, debugging is efficient with simultaneously monitoring and management of multiple networks and PLCs.
Management of Multiple Networks
The operation of networks with configurations consisting of
multiple networks including PLC networks such as
EtherNet/IP and Controller Link, field networks such as
DeviceNet and CompoNet, and networks for Programmable
Terminals and Serial Devices, can be restored simultaneously
from the CX-One. Onsite start up and debugging can be
conducted efficiently and without errors because PLCs
and devices can be selected from the window to transfer
programs and parameter data to the computer during
operation.
Ladder diagram Monitoring for
Multiple PLCs
Multiple PLCs can be monitored by displaying them in series on the screen. This way it is easy to debug data links between PLCs and monitor the
inputs and outputs of different PLCs.
PLC1
PLC2
PLC3
Node 1
Node 2
Node 3
Group Monitoring of Multiple PLC Input/Outputs in the Watch Window
The desired I/O data can be selected for multiple PLCs, such as input bits, output bits, and word I/O data, and monitored simultaneously. There
are also functions such as the Binary Monitor and Forced Set/Reset functions that enables graphical monitoring the ON/OFF status of word data.
All of these monitoring functions are easy to use.
Addresses that
you want to
monitor can be
registered for
each debugging
segment.
12
CX-One
Ver.4.0
Functionality and operability has been significantly upgraded compared to the previous data trace function. The new data trace function provides
comprehensive debugging, such as I/O comment display of sampled addresses, specification using symbols, checking the measurement time between
two selected points, and layering waveforms. Furthermore, data sampled from the CPU Unit’s trace memory can be saved to a file on the computer at
Data Trace Function
Sampled values from a specific
word will be displayed.
Continuous Data Trace
Logging
Applicable Models : CJ2
Third
Second
First
The traced waveforms can be displayed as layers.
Sampled value from a
specific input bit will be
displayed.
SYSMAC CJ2
Programs can be debugged using a computer without the actual PLC. A wide range of languages, such as ladder diagram, sequential function
force-set/reset, breakpoints can be set, and a PLC error simulator can be used.
Simulation of SFC, Ladder Diagrams, and Function Blocks
Forced set/reset
Ordering Information
Can be used for SFC steps
and transitions.
Breakpoints
CX-One Lite
Breakpoints can be inserted
anywhere in the program,
such as for input bits,
output instructions, special i
nstructions, or function blocks.
Breakpoints
No Size Restrictions for Online Editing of Function Blocks and
Sequential Function Charts
Online Web Services
Error Simulation
It is easy to debug errors that are difficult
to generate with the actual PLC. Debug
contents can be saved and used in test
document.
FA Communications Software
charts (SFC), structured text (ST), and programs within function blocks are supported. Furthermore, programs can be edited online, bits can be
Component Tools
Simulation Debugging
Debugging
High-speed sampling to the
PLC trace memory
Network
Data is collected in the computer
at a specified interval
Position Control
The CJ2 CPU Units can trace data for long periods of time.
Data can be saved in CSV files.
Reusable Designs
a specified frequency. This can be used as for long-term logging of data.
Easy Programming
Time Require for Debugging and Maintenance Has Been Reduced with
the Comprehensive Data Trace Function
Applicable Models : CJ2
There are no size restrictions for the function blocks and SFC that can be edited online.
13
Component Tools
(Screen Designing)
Products Are Highly Compatible and Easy to Use Because They Are from a Comprehensive PLC Manufacturer
The CX-Designer Simplifies the Processes from Screen
Design to Debugging for the NS-series Programmable Terminals
The time required for designing can be significantly reduced because of the compatibility with SYSMAC
CJ-series PLCs. The process of designing screens is easier with expanded function.
Applicable Models :
NS Series NSJ Series
Integrated Simulation with the PLC Ladder Diagrams
Test functions for the CX-Designer and CX-Programmer are linked through the CX-Simulator on a computer. This enables screens and ladder diagrams to be
checked simultaneously, significantly improving the debugging efficiency. A new Integrated Simulation Button has been added to the CX-Programmer.
Furthermore, work efficiency has been significantly improved with the function that enables work windows to be pinned in front, and a flexible zoom function.
Screens and Ladder Diagrams Can Be Simultaneously Checked on a Computer
Ladder Diagram Window
Touch Panel Screen
Linked
Single-key Simulation
Within computer
CJ2 Data Structure Supported, Enhanced designing efficiency and design work reduction in overall system
Special function which can be used for a system with Omron PLC CJ2 and NS-series programmable terminal.
Just drag the data structures on the CX-Programmer and drop it on the CX-Designer.
Data structures can be shared between the PLC ladder program and screen editor of programmable terminal.
Note1: To use CJ2 data structure, prepare CX-Designer Ver.3.2 or higher and NS system program Ver.8.4.
Note2: This function can be used when the PLC and programmable terminal are connected via EtherNet/IP.
CX-Designer
CX-Programmer
Drag
and
drop
14
CX-One
Ver.4.0
There are over 3,000 Smart Active Parts that can directly access OMRON PLCs and components. Simply select and paste a part from
the SAP library onto the screen. Detailed screens and ladder diagrams do not need to be created.
Screen Designing Tools
CX-Designer
Using Software Components, Error Checking and
Parameter Setting Can Be Done without a Computer
FROM
Computer Software
TO
EASY Tools (Software Function SAP Library)
Transfer
Debugging
CJ2
Network
Immediate creation of
Temperature Controller
Settings and Monitor Screens
Position Control
There are many software components in the Software Function SAP Library that
can be easily incorporated into the NS-series Programmable Terminals. Simply
select and paste software components on the screen. Device errors can be
checked and parameters set without a computer.
Drag
and
drop
Reusable Designs
SAP Library of Temperature
Controller Components
Easy Programming
Communications Components and the Smart Active Parts(SAP)Library Significantly
Reduces the Time Required to Create Ladder Diagrams and Screens
E5AN
PLC CPU Unit
Monitor Screen
EJ1
MX
DeviceNet Monitor Screen
The Troubleshooter SAPs Can Be Used Onsite without Computers or Manuals
Improved Troubleshooter
SAP Library
NV Series
Applicable Models :
NV Series
CX-One Lite
Use the NV-Designer to Easily and Quickly
Design Screens for the NV Series of Compact PTs
Ordering Information
Basic I/O Unit Troubleshooter SAP
Online Web Services
Position Control Unit Troubleshooter SAP
In addition to the DeviceNet Units and Position
Control Units, the CX-Designer also includes Basic
I/O Unit, Analog I/O Units, Serial Communications
Units, High-speed Counter Units, Controller Link Unit,
and ID Sensor Units. Including the EtherNet Units
and Motion Control Units is planned in future
development stages.
FA Communications Software
There is a troubleshooter SAP library that covers all PLC Units. If there is a PLC error, the troubleshooter SAP library explains the cause and
how to implement countermeasures in a way that it is easy to understand.
Component Tools
NCF Unit
Setting Screen
1
15
Component Tools
(Motion Control)
Easily Built Intelligent Motion Control
Optimum Motion System Support for Applications
with Motion Networks or Generic Interfaces
CX-Drive
Support from system starting to Maintenance. Also Provides EtherCAT Compatibility
Easy Setup and Adjustment
Tool
Parameters
Servo Drive or Inverter parameters can be set as easily as with a
digital operator. With an EtherCAT system, Servo Drive parameters
can be set and status can be monitored through the PLC.
Simple Gain Adjustment
You can use a wizard to complete gain adjustment in five minutes or
less per axis simply by entering the machine configuration and the
target set time.
SYSMAC CJ Series
Position Control Units
with EtherCAT interface
USB
You can also
connect the
CX-Drive to G5-series
Servo Drives directly
with USB.
OMNUC G5 Series
AC Servo drive with built-in
EtherCAT communications
Simple FFT
Simple Gain Adjustment
Measurement, Analysis, and Monitoring
Simple FFT
You can measure the frequency characteristics of the system
and diagnose resonant frequencies. Apply the notch filter to
resonant frequency to achieve higher responsivity.
Status Monitoring
Data traces can be used to monitor the speed or torque as easily
as with an oscilloscope.
Stand alone CX-Drive (WS02-DRVC1) version is Ver.1.91.
It does not support gain adjustment function.
Applicable Models : Servo OMNUC G5/G/W Series SMARTSTEP 2/SMARTSTEP Junior/SMARTSTEP A Series
Easy Management of Parameters While Connected to PLCs
Inverter 3G3MX2/3G3 X Series 3G3JV/3G3MV/3G3RV/3G3RV-V1
CX-Motion-NCF
Settings can be modified while connected
Parameters that can be edited
Easily set, transfer, and verify parameters.
Position Control Unit
axis settings and
Servo Drive Parameters
Wiring can be checked while connected
Monitor status and present values.
Simultaneously monitor the Servo Drives for up to four axes.
Operation can be checked while connected
Position Control Units with MECHATROLINK-II interface
Execute servo locks, jogging, and error resetting. Display error codes and
ON/OFF status for each axis. Monitor present values and busy status.
Even Easier to Start Up a System
Applicable Models : CS1W/CJ1W-NCF71/NC271/NC471
CX-Motion-MCH
Programming Is Easy
Easily set, transfer, and verify tasks and axis parameters.
Perform syntax checks for motion programs.
Debugging Programs Is Easy
Execute servo locks, jogging, stepping, origin searches, origin returns,
force-setting the origin, error resetting, absolute origin setting, and teaching.
Display error codes and I/O ON/OFF status for each axis.
Use breakpoints to easily debug programming.
Checking Operation Is Easy
Use data tracing to trace variables in the Motion Control Unit.
Display the results in graphs to easily check operation and make adjustments.
16
Debugging motion programs
Data trace results
Insert a breakpoint
where you want to
pause the program
Variable values
can be
changed
Motion Control Units with MECHATROLINK-II interface
Applicable Models : CS1W/CJ1W-MCF71
Component Tools
(Temperature Controllers)
CX-One
Ver.4.0
CX-Thermo
Setting Temperature Controller Parameters Is Easier
CX-Thermo
Parameter
Property
Window
Work
space
Easy Parameter Settings
Parameters can be set even for Temperature Controllers that
do not support communications.
Parameters can be saved, and then copied, or reused and edited
(Parameters can be exported in CSV or HTML format.)
Position Control
Parameters can be easily set from a list
Reusable Designs
The CX-Thermo/CX-Process Tool Software Supports
High-level Temperature Control
Easy Programming
From Parameter Settings to Temperature Data Management
Displays Only What Is Used
Component Tools
Programming for the Process Controller Is Easier
Parameter
List
CX-Process Tool
Control Programs Can Be Constructed By Pasting Function Blocks
Control programs can be constructed by pasting function
blocks and connecting them. They can be used for simple PID
control, program control, and cascade control.
Project
workspace
Applicable Units :
CJ1G-CPU4 P/CPU4 P-GTC,
CS1W-LCB01/LCB05/LCB05-GTC,
CS1W-LC001 *,CS1D-CPU6 P
* Discontinuation models in March 2012.
Adjusting Parameters While
Monitoring Trends
PID parameters can be adjusted while
monitoring the present value (PV), setting point
(SP), and manipulated variable (MV). Trend data
can be saved in CSV format.
(CX-Thermo Trend Viewer, CX-Process Tool Support
Software Tuning Screen)
Controlling with a Reliable Control Algorithm
(See note.)
The execution of the autotuning (AT) function that calculates the PID constants and the fine
tuning (FT) function that improves controllability exactly as required are made easy with an
intuitive user interface. The interference overshooting adjustment function is supported to
adjust overshooting when interference occurs, and the gradient temperature control function
achieves constant internal temperatures for multi-point temperature control with interference.
CX-One Lite
CX-Thermo/CX-Process Tool Support Software
Ordering Information
Output
Window
Screens for the NS-series PTs (NS runtime screen) are
automatically generated from the function block programs.
Standard control screens and tuning screens do not need to be
created manually.
Online Web Services
(block diagrams, etc.)
Easy Creation of an HMI
FA Communications Software
Control Can Be Customized
Content check
Debugging
Output
Window
Applicable Units :
E5GN/E5CN/E5CN-H/E5AN/E5AN-H/E5EN/
E5EN-H,EJ1,E5ZN,E5AR/E5AR-T/
The DeviceNet type is excluded
E5ER/E5ER-T
Network
To avoid unintentional use of parameters, unused parameters
can be masked (i.e., hidden)
Note: Supported functions depends on the product being used. Refer to product manuals for details.
17
FA Communications Software
Easily write programs to read and write
PLC data with VB or VC#.
CX-Compolet
User Application
CX-Compolet
VB.NET or VC#.NET
Simply paste to the form and
specify the tags (addresses).
Easy to Use without Any Technical Knowledge
.NET
Control
Provides software components that help you easily
and quickly develop PLC communications.
Read and write PLC data without the need to
consider differences between networks.
Supports Microsoft Visual Studio .NET 2008.
For the CJ2 with EtherNet/IP functionality, I/O
memory in the PLC can be accessed by using tag
names rather than addresses.
Array variable access is possible.
Example
Example:
Reading I/O
O
Memory
SYSMAC Gateway
y
DM0
Press the button to read the
value (D0 in this example).
1234
SYSMAC PLC
Communications Middleware to Connect a
Computer and SYSMAC PLCs
Applications
SYSMAC Gateway
Direct Connection of the Industrial Ethernet: EtherNet/IP
SYSMAC Gateway
Direct Access to High-speed and
High-capacity Networks
In addition to FINS communications, operation of
SYSMAC Gateway has been verified on EtherNet/IP.
Absorbs differences in the physical layer between
RS-232C, USB, Ethernet, EtherNet/IP, and
Controller Link.
Just install the software on the computer to enable
data communications for controls and information.
Serial
EtherNet/IP
Real PLC
Real PLC
Controller Link
Real PLC
Note: Communications are possible via
USB and Ethernet too.
Product Positioning
FA Communications Software
CX-Compolet
System Application
Device-embedded Applications
CX-Compolet
(Previously called “SYSMAC Compolet.”)
Easy PLC Data Reading
and Writing with VB.NET
and VC#.NET Control Objects
SYSMAC Gateway
FINS/CIP Communications Middleware
SYSMAC Gateway
18
CX-Compolet software
enables easily reading and
writing PLC data using Visual
Basic.NET and Visual C#.NET.
It is the successor to
SYSMAC Compolet.
(formerly FinsGateway)
RS-232C
USB
EtherNet/IP
Ethernet
Controller Link
SYSMAC PLC
SYSMAC PLC
SYSMAC PLC
SYSMAC PLC
SYSMAC PLC
SYSMAC Gateway can be
used as the communications
driver on most networks. It is
the successor to FinsGateway
and has inherited all
FinsGateway functionality.
Online Web Services
Web Support Services for CX-One
Easy Programming
OMRON’S CX-One offers many service options in the Internet environment so that engineers and online
support is available from anywhere in the world 24 hours a day.
Online User Registration
Reusable Designs
Position Control
When you register online as a user of CX-One, all CX-One
software components can be registered at once. The
online registration website can be accessed from Japan,
North America, South America, Central America, Europe,
Africa, Asia, China, Taiwan, and Korea. You can access
the Internet services from anywhere once you have
registered.
Network
Automatic Update
Debugging
With the automatic update function of CX-One, the latest
update information for your computer environment can be
searched for and applied using the network environment.
Your CX-One can be constantly updated to the latest state.
It is also possible to update only the necessary tools.
Component Tools
Online Web Services
Control devices that were made available after you
purchased the Support Software can be used if you
download the latest Smart Libraries from the Internet. A
customized library can be made by downloading the
Smart FB Library and Smart Active Parts for the hardware
that you require. Programming is also easy by selecting
and pasting the necessary parts.
FA Communications Software
Download Services
Ordering Information
CX-One Lite
19
Ordering Information
Ordering Information
Product name
FA Integrated Tool
Package CX-One
Ver. 4.1
Specifications
Model
Standards
DVD
CXONE-AL01D-V4
ò
3 licenses
DVD
CXONE-AL03D-V4
ò
10 licenses
DVD
CXONE-AL10D-V4
ò
30 licenses
DVD
CXONE-AL30D-V4
ò
50 licenses
DVD
CXONE-AL50D-V4
ò
Number of licenses
Media
1 licenses
The CX-One is a
comprehensive software
package that integrates
Support Software for OMRON
PLCs and components.
CX-One runs on
the following OS.
Windows XP
(Service Pack 3 or higher),
Vista or 7.
Note:Except for Windows XP
64-bit version.
Note: The CX-One is also available on CD (CXONE-AL
C-V4).
Site licenses are available for users who will run CX-One on multiple computers. Ask your OMRON sales representative for details.
System Requirements
Item
Requirement
Operating system (OS) (See note1,2.)
Japanese or English System
Microsoft Windows XP (Service Pack 3 or higher), Vista, or 7
CPU
Processor recommended by Microsoft.
Memory (See note3.)
Memory recommended by Microsoft.
Hard disk
Approx. 2.8 GB or more of available memory is required to install all of the CX-One.
Display
XGA (1024×768), High Color (16-bit) or higher
Disk drive
CD-ROM or DVD-ROM drive
Communications ports
RS-232C port, USB port, or Ethernet port (See note4.)
Other
To register online as a user using the Internet, hardware for a connection (such as a modem)
and access to the Internet are required.
Note1. CX-One Operating System Precaution :
1) System requirements and hard disk space may vary with the system environment.
2) Except for Windows XP 64-bit version.
2. The following restrictions apply when CX-One is used with Microsoft Windows Vista / 7 .
1) Some Help files cannot be accessed.
The Help files can be accessed if the Help program distributed by Microsoft for Windows Vista (WinHlp32.exe) is installed. Refer to
the Microsoft homepage listed below or contact Microsoft for details on installing the file.
(The download page is automatically displayed if the Help files are opened while the user is connected to the Internet.)
http://support.microsoft.com/kb/917607/en-us
2) Restrictions apply to operation of some applications. Refer to the Setup Manual for details.
3. The amount of memory required varies with the Support Software used in CX-One for the following Support Software. Refer to user
documentation for individual Support Software for details.
CX-Programmer, CX-Designer, CX-Thermo, CX-Simulator, CX-Protocol, CX-Motion, CX-Drive, CX-Process Tool,
and Faceplate Auto-Builder for NS.
4. Refer to the hardware manual for your PLC for hardware connection methods and cables to connect the computer and PLC.
20
CX-One
Ver.4.0
Support Software in CX-One Version 4.1
The following tables lists the Support Software that can be installed from CX-One
Outline
CX-Protocol
Ver.1.9
Application software to create protocols (communications sequences) between SYSMAC CS/CJ/CP/NSJ-series or
C200HX/HG/HE Serial Communications Boards/Units and general-purpose external devices.
CX-Simulator
Ver.1.9
Application software to simulate SYSMAC CS/CJ/CP/NSJ-series CPU Unit operation on the computer to debug PLC programs
without a CPU Unit.
CX-Position
Ver.2.5
Application software to create and monitor data for SYSMAC CS/CJ-series Position Control Units.(except for High-speed type)
CX-Motion-NCF
Ver.1.9
Application software to create and monitor data for SYSMAC CS/CJ-series Position Control Units with MECHATOLINK-II (NC 71).
CX-Motion-MCH
Ver.2.2
Application software to create data and motion programs and to monitor data for SYSMAC CS/CJ-series
Motion Control Units with MECHATOLINK-II (MCH71).
CX-Motion
Ver.2.3
Application software to create data for SYSMAC CS/CJ-series, C200HX/HG/HE, and CVM1/CV-series Motion Control Units,
and to create and monitor motion control programs.
CX-Drive
Ver.2.2
Application software to set and control data for Inverters and Servos.
CX-Process Tool
Ver.5.2
Application software to create and debug function block programs for SYSMAC CS/CJ-series Loop Controllers (Loop Control
Units/Boards, Process Control CPU Units, and Loop Control CPU Units).
Faceplate AutoBuilder for NS
Ver.3.1
Application software that automatically outputs screen data as project files for Ns-series PTs from tag information in function
block programs created with the CX-Process Tool.
CX-Designer
Ver.3.2
Application software to create screen data for NS-series PTs.
NV-Designer
Ver.1.1
Application software to create screen data for NV-series small PTs.
CX-Configurator FDT
Ver.1.2
Application software for setting various units by installing its DTM module.
CX-Thermo
Ver.4.2
Application software to set and control parameters in components such as Temperature Control Units.
CX-FLnet
Ver.1.0
Application software for system setting and monitoring of SYSMAC CS/CJ-series Fl-net Units.
Network Configurator
Ver.3.2
Application software to set up and monitor tag data links for CJ2 (Built-in EtherNet/IP) CPU Units and EtherNet/IP Units.
CX-Server
Ver.4.5
Middleware necessary for CX-One applications to communicate with OMRON components, such as PLCs, Display Devices, and Temperature Control Units.
PLC Tools
(Installed automatically.)
CX-One Lite
Utility software that helps you to debug PLCs. It helps you to monitor the I/O status and to monitor/change present values within
the PLC you specify.
Ordering Information
Ver.1.6
Online Web Services
Switch Box Utility
FA Communications Software
Application software to build and set up FA networks, such as Controller Link, DeviceNet, CompoNet, CompoWay, and Ethernet networks.
The Routing Table Component and Data Link Component can be started from here. DeviceNet Configuration functionality is also included.
Component Tools
Ver.2.4
Debugging
CX-Integrator
Network
Application software to create and debug programs for SYSMAC CS/CJ/CP/NSJseries, C-series, and CVM1/C-series CPU Units.
Data can be created and monitored for high-speed-type Position Control Units and Position Control Units with EtherCAT interface.
Position Control
Ver.9.2
Reusable Designs
CX-Programmer
Easy Programming
Support Software in CX-One
A group of components used with CX-One applications, such as the CX-Programmer and CX-Integrator. Includes the following:
I/O tables, PLC memory, PLC Setup, Data Tracing/Time Chart Monitoring, PLC Error Logs, File Memory, PLC clock, Routing Tables, and Data Link Tables.
21
Ordering Information
Related Products
FA Communications Software
Pruduct name
Specifications
Model
CX-Compolet ∗1
Software components that can make it easy to create programs for communications
between a computer and controllers.
This packaged product bundles SYSMAC Gateway.
Development environment:
Visual Studio.NET2003/.NET2005/.NET2008/.NET2010
Development languages:
Visual Basic .NET, Visual C#.NET, Visual Basic Ver. 5/6 ∗2
SYSMAC Gateway ∗3
Communications middleware for personal computers running Windows.
Supports CIP communications and tag data links (EtherNet/IP) in addition to
FinsGateway functions.
Standards
WS02-CPLC1
ò
WS02-SGWC1
ò
Note: One license is required per computer. Refer to the CJ2 CPU Unit Catalog (Cat. No. V302) for details.
∗1. You can also purchase the CX-Compolet without the SYSMAC Gateway. Order WS02-CPLC2.
∗2. Only functions provided by Compolet V2 as ActiveX controls are supported for Visual Basic version 5 or 6.
∗3. SYSMAC Gateway includes Fins Gateway. A software development kit called the SYSMAC Gateway SDK is also available to write communications programs for the
SYSMAC Gateway.
Correspondence between supported OS and Connected Networks
Ethernet
Controller Link
Pruduct name
RS-232C
Ethernet(FINS)
EtherNet/IP
SYSMAC LINK
PCI
ISA
Windows XP
Supported
Supported
Supported
Supported
Supported
Supported
Windows Vista
Supported
Supported
Supported
Supported
Supported
Supported
Windows 7
Supported
Supported
Supported
Supported
Windows Server 2003
Supported
Supported
Supported
Supported
Windows Server 2008
Supported
Supported
Supported
Supported
∗ Except for 64-bit version
22
USB
Supported ∗ Not supported
Supported
Supported ∗ Not supported
Not supported
Supported
Not supported
The Ideal Software Package for Compact PLCs
Easy Programming
Simplified setting operations are ensured by Micro PLC Edition CX-Programmer (the ideal PLC programming
software for small-scale systems), along with Support Software to set NS/NV-series PTs, Temperature
Controllers, and Servo Drives.
Reusable Designs
Position Control
Network
Debugging
Features
Component Tools
Simplified setting operations are ensured by Micro PLC Edition CX-Programmer (the ideal PLC programming
software for small-scale systems), along with Support Software to set NS/NV-series PTs, Temperature Controllers,
and Servo Drives.
Total lead time until the system is up and running is reduced.
FA Communications Software
Support Software in CX-One
The following tables lists the Support Software that can be installed from CX-One
Ver.9.
CX-Designer
Ver.3.
CX-Integrator
Ver.2.
NV-Designer
Ver.1.
Switch Box Utility
Ver.1.
CX-Thermo
Ver.4.
CX-Simulator
Ver.1.
Network Configurator
Ver.3.
CX-Drive
Ver.2.
CX-Server
Ver.4.
Online Web Services
Micro PLC Edition CX-Programmer *
Applicable models: CP1 , CPM , SRM1
The CX-One and CX-One Lite cannot be simultaneously installed on the same computer.
Product name
CX-One Lite is a subset of the complete CX-One package
that provides only the Support Software required for micro
PLC applications.
CX-One Lite runs on the following OS.
Windows XP (Service Pack 3 or higher), Vista or 7.
*Except for Windows XP 64-bit version.
Number of licenses
Media
1 license
CD
Model
CXONE-LT01C-V4
Standards
-
CX-One Lite
FA Integrated
Tool Package
CX-One Lite
Ver.4.1
Specifications
Ordering Information
Ordering information
23
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and
workmanship for a period of one year (or other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING
NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE
PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE
HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF
THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE
PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE,
OR STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the
product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER
CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE
PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR
REPAIR.
The application examples provided in this catalog are for reference only. Check functions and
safety of the equipment before use.
Never use the products for any application requiring special safety requirements, such as nuclear
energy control systems, railroad systems, aviation systems, medical equipment, amusement
machines, vehicles, safety equipment, or other application involving serious risk to life or property,
without ensuring that the system as a whole has been designed to address the risks, and that the
OMRON products are properly rated and installed for the intended use within the overall
equipment or system.
Note: Do not use this document to operate the Unit.
OMRON Corporation
Industrial Automation Company
Authorized Distributor:
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
© OMRON Corporation 2009-2012 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
Printed in Japan
CSM_6_1_0312
Cat. No. R134-E1-13
0412 (0405)(w)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement