Intel® NUC Board NUC5PGYH Technical Product Specification

Add to my manuals
76 Pages

advertisement

Intel® NUC Board NUC5PGYH Technical Product Specification | Manualzz

Intel® NUC Board

NUC5PGYH

Technical Product Specification

June 2016

Order Number: H78081-006

The Intel NUC Board NUC5PGYH may contain design defects or errors known as errata that may cause the product to deviate from published specifications. Current characterized errata are documented in the Intel NUC Board NUC5PGYH Specification Update.

Revision History

Revision

001

002

003

004

005

006

Revision History Date

First release of the Intel

®

NUC Board NUC5PGYH Technical Product Specification September 2015

Specification Clarification

Specification Clarification

Specification Clarification

Specification Change

Specification Clarification

October 2015

November 2015

March 2016

May 2016

June 2016

Disclaimer

This product specification applies to only the standard Intel ® NUC Board with BIOS identifier PYBSWCEL.86A.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL

®

PRODUCTS. NO LICENSE, EXPRESS OR

IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.

EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO

LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR

ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL

INJURY OR DEATH MAY OCCUR.

All Intel

®

NUC Boards are evaluated as Information Technology Equipment (I.T.E.) for use in personal computers (PC) for installation in homes, offices, schools, computer rooms, and similar locations. The suitability of this product for other PC or embedded non-PC applications or other environments, such as medical, industrial, alarm systems, test equipment, etc. may not be supported without further evaluation by Intel.

Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.

Intel may make changes to specifications and product descriptions at any time, without notice.

Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or

“undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.

Intel processor numbers are not a measure of performance. Processor numbers differentiate features within each processor family, not across different processor families: Go to:

Learn About Intel

®

Processor Numbers

Intel NUC Boards may contain design defects or errors known as errata, which may cause the product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications before placing your product order.

Intel and Pentium are trademarks of Intel Corporation in the U.S. and/or other countries.

* Other names and brands may be claimed as the property of others.

Copyright  2015, 2016 Intel Corporation. All rights reserved.

Board Identification Information

Basic Intel ® NUC Board NUC5PGYH Identification Information

AA Revision

H78168-100

BIOS Revision

PYBSWCEL.86A

Notes

1,2

Notes:

1. The AA number is found on a small label on the component side of the board.

2. Intel

®

Pentium

®

processor N3700, used on this AA revision, consists of the following component:

Device Stepping S-Spec Numbers

Intel Pentium processor N3700 C0 SR29E

Specification Changes or Clarifications

The table below indicates the Specification Changes or Specification Clarifications that apply to the Intel NUC Board NUC5PGYH.

Specification Changes or Clarifications

Date

October 2015

November 2015 Spec Clarification

March 2016

May 2016

June 2016

Type of Change

Spec Clarification

Spec Clarification

Spec Change

Spec Clarification

Description of Changes or Clarifications

Removed all reference to the Front Panel Header as it was not stuffed on the board.

Updated the operating temperature in Table 22. Environmental

Specifications.

Added a Note to Section 2.2.4.4 to clarify what the Auxiliary Power Connector

is used for.

• Deleted the Near Field Communication (NFC) header and all related text.

Added Section 2.2.4.5 Front Panel Header (2.0 mm Pitch).

• Update SATA speed to 6.0 Gb/s.

Errata

Current characterized errata, if any, are documented in a separate Specification Update. See http://www.intel.com/content/www/us/en/nuc/overview.html

for the latest documentation.

iii

Intel NUC Board NUC5PGYH Technical Product Specification

iv

Preface

This Technical Product Specification (TPS) specifies the board layout, components, connectors, power and environmental requirements, and the BIOS for Intel

®

NUC Board NUC5PGYH.

Intended Audience

The TPS is intended to provide detailed technical information about Intel NUC Board NUC5PGYH and its components to the vendors, system integrators, and other engineers and technicians who need this level of information. It is specifically not intended for general audiences.

What This Document Contains

4

5

2

3

Chapter

1

Description

A description of the hardware used on Intel NUC Board NUC5PGYH

A map of the resources of the Intel NUC Board

The features supported by the BIOS Setup program

A description of the BIOS error messages, beep codes, and POST codes

Regulatory compliance and battery disposal information

Typographical Conventions

This section contains information about the conventions used in this specification. Not all of these symbols and abbreviations appear in all specifications of this type.

Notes, Cautions, and Warnings

NOTE

Notes call attention to important information.

CAUTION

Cautions are included to help you avoid damaging hardware or losing data.

v

Intel NUC Board NUC5PGYH Technical Product Specification

Other Common Notation

# Used after a signal name to identify an active-low signal (such as USBP0#)

GB

GB/s

Gb/s

Gigabyte (1,073,741,824 bytes)

Gigabytes per second

Gigabits per second

KB

Kb kb/s

MB

MB/s

Mb

Mb/s

TDP xxh x.x V

*

Kilobyte (1024 bytes)

Kilobit (1024 bits)

1000 bits per second

Megabyte (1,048,576 bytes)

Megabytes per second

Megabit (1,048,576 bits)

Megabits per second

Thermal Design Power

An address or data value ending with a lowercase h indicates a hexadecimal value.

Volts. Voltages are DC unless otherwise specified.

This symbol is used to indicate third-party brands and names that are the property of their respective owners. vi

Contents

Revision History

Board Identification Information .................................................................................................................... iii

Errata ........................................................................................................................................................................... iii

Preface

Intended Audience................................................................................................................................................. v

What This Document Contains ......................................................................................................................... v

Typographical Conventions ............................................................................................................................... v

1 Product Description

1.1

Overview ...................................................................................................................................................... 11

1.1.1

Feature Summary .................................................................................................................. 11

1.1.2

Board Layout (Top) ............................................................................................................... 13

1.1.3

Board Layout (Bottom) ........................................................................................................ 15

1.1.4

Block Diagram ......................................................................................................................... 17

1.2

Online Support .......................................................................................................................................... 18

1.3

Processor ..................................................................................................................................................... 18

1.4

System Memory ........................................................................................................................................ 19

1.5

Processor Graphics Subsystem ......................................................................................................... 21

1.5.1

Integrated Graphics .............................................................................................................. 21

1.6

USB ................................................................................................................................................................. 22

1.7

SATA Interface........................................................................................................................................... 22

1.7.1

AHCI Mode ................................................................................................................................ 22

1.8

Real-Time Clock Subsystem ................................................................................................................ 23

1.9

Audio Subsystem ..................................................................................................................................... 24

1.9.1

Mini-TOSLINK Interface ...................................................................................................... 25

1.9.2

Audio Subsystem Software ............................................................................................... 25

1.10

LAN Subsystem ......................................................................................................................................... 26

1.10.1

Realtek* 8111HN Gigabit Ethernet Controller .......................................................... 26

1.10.2

LAN Subsystem Software................................................................................................... 26

1.10.3

RJ-45 LAN Connector with Integrated LEDs .............................................................. 27

1.10.4

Wireless Network Module .................................................................................................. 27

1.11

Hardware Management Subsystem ................................................................................................. 28

1.11.1

Hardware Monitoring ........................................................................................................... 28

1.11.2

Fan Monitoring........................................................................................................................ 28

1.11.3

Thermal Solution ................................................................................................................... 29

1.12

Power Management ................................................................................................................................ 30

1.12.1

ACPI ............................................................................................................................................. 30

1.12.2

Hardware Support ................................................................................................................. 32

vii

Intel NUC Board NUC5PGYH Technical Product Specification

2 Technical Reference

2.1

Memory Resources .................................................................................................................................. 35

2.1.1

Addressable Memory ........................................................................................................... 35

2.2

Connectors and Headers ...................................................................................................................... 35

2.2.1

Front Panel Connectors ...................................................................................................... 36

2.2.2

Back Panel Connectors ....................................................................................................... 36

2.2.3

Headers and Connectors (Top) ........................................................................................ 37

2.2.4

Connectors and Headers (Bottom)................................................................................. 38

2.3

BIOS Security Jumper ............................................................................................................................ 48

2.4

Mechanical Considerations .................................................................................................................. 50

2.4.1

Form Factor .............................................................................................................................. 50

2.5

Electrical Considerations ...................................................................................................................... 51

2.5.1

Power Supply Considerations .......................................................................................... 51

2.5.2

Fan Header Current Capability ........................................................................................ 51

2.6

Thermal Considerations ........................................................................................................................ 51

2.7

Reliability ..................................................................................................................................................... 54

2.8

Environmental ........................................................................................................................................... 54

3 Overview of BIOS Features

3.1

Introduction ................................................................................................................................................ 55

3.2

BIOS Flash Memory Organization ..................................................................................................... 55

3.3

System Management BIOS (SMBIOS) .............................................................................................. 55

3.4

Legacy USB Support ............................................................................................................................... 56

3.5

BIOS Updates ............................................................................................................................................. 56

3.5.1

Language Support ................................................................................................................. 57

3.5.2

Custom Splash Screen ........................................................................................................ 57

3.6

BIOS Recovery ........................................................................................................................................... 58

3.7

Boot Options .............................................................................................................................................. 59

3.7.1

Network Boot........................................................................................................................... 59

3.7.2

Booting Without Attached Devices ................................................................................ 59

3.7.3

Changing the Default Boot Device During POST ..................................................... 59

3.7.4

Power Button Menu .............................................................................................................. 60

3.8

Hard Disk Drive Password Security Feature ................................................................................. 61

3.9

BIOS Security Features .......................................................................................................................... 62

4 Error Messages and Blink Codes

4.1

Front-panel Power LED Blink Codes ................................................................................................ 63

4.2

BIOS Error Messages .............................................................................................................................. 63

5 Regulatory Compliance and Battery Disposal Information

5.1

Regulatory Compliance ......................................................................................................................... 65

5.1.1

Safety Standards ................................................................................................................... 65

5.1.2

European Union Declaration of Conformity Statement ........................................ 66

5.1.3

Product Ecology Statements ............................................................................................ 67

5.1.4

EMC Regulations .................................................................................................................... 67

viii

Contents

5.1.5

e-Standby and ErP Compliance ...................................................................................... 70

5.1.6

Regulatory Compliance Marks (Board Level) ............................................................. 71

5.2

Battery Disposal Information .............................................................................................................. 72

Figures

1. Major Board Components (Top) ........................................................................................................ 13

2. Major Board Components (Bottom) ................................................................................................. 15

3. Block Diagram ............................................................................................................................................ 17

4. Memory Channel and SO-DIMM Configuration .......................................................................... 20

5. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out ................................................................................ 24

6. Mini-TOSLINK Adaptor .......................................................................................................................... 25

7. LAN Connector LED Locations ........................................................................................................... 27

8. Thermal Solution and Fan Header .................................................................................................... 29

9. Location of the Standby Power LED ................................................................................................ 34

10. Front Panel Connectors ......................................................................................................................... 36

11. Back Panel Connectors .......................................................................................................................... 36

12. Headers and Connectors (Top) .......................................................................................................... 37

13. Connectors and Headers (Bottom) ................................................................................................... 38

14. Connection Diagram for Front Panel Header (2.0 mm Pitch) ................................................ 44

14. Location of the CIR Sensor ................................................................................................................... 46

15. Connection Diagram for Internal USB 2.0 Dual-Port Header (1.25 mm Pitch) .............. 47

16. Location of the BIOS Security Jumper ............................................................................................ 48

17. Board Dimensions .................................................................................................................................... 50

18. Board Height Dimensions ..................................................................................................................... 51

19. Localized High Temperature Zones ................................................................................................. 52

Tables

1. Feature Summary ..................................................................................................................................... 11

2. Components Shown in Figure 1......................................................................................................... 14

3. Components Shown in Figure 2......................................................................................................... 16

4. Supported Memory Configurations ................................................................................................. 19

5. LAN Connector LED States ................................................................................................................... 27

6. Effects of Pressing the Power Switch .............................................................................................. 30

7. Power States and Targeted System Power ................................................................................... 31

8. Wake-up Devices and Events ............................................................................................................. 32

9. Headers and Connectors Shown in Figure 12 ............................................................................. 37

10. Connectors and Headers Shown in Figure 13 ............................................................................. 39

11. VGA Header ................................................................................................................................................ 40

12. SATA Power Header (1.25 mm Pitch) .............................................................................................. 40

13. Dual-Port Internal USB 2.0 Header (1.25 mm Pitch) ................................................................. 40

14. M.2 2230 Module (Mechanical Key E) Connector ...................................................................... 41

15. SDXC Card Reader Connector ............................................................................................................ 42

16. Auxiliary Power Connector ................................................................................................................... 43

18. Front Panel Header (2.0 mm Pitch) .................................................................................................. 44

ix

Intel NUC Board NUC5PGYH Technical Product Specification

19. States for a One-Color Power LED.................................................................................................... 45

20. States for a Dual-Color Power LED ................................................................................................... 45

17. BIOS Security Jumper Settings .......................................................................................................... 49

18. Fan Header Current Capability ........................................................................................................... 51

19. Thermal Considerations for Components ..................................................................................... 53

20. Tcontrol Values for Components ...................................................................................................... 53

21. Environmental Specifications ............................................................................................................. 54

22. Acceptable Drives/Media Types for BIOS Recovery ................................................................. 58

23. Boot Device Menu Options .................................................................................................................. 59

24. Master Key and User Hard Drive Password Functions ............................................................. 61

25. Supervisor and User Password Functions ..................................................................................... 62

26. Front-panel Power LED Blink Codes ................................................................................................ 63

27. BIOS Error Messages .............................................................................................................................. 63

28. Safety Standards ...................................................................................................................................... 65

29. EMC Regulations ....................................................................................................................................... 67

30. Regulatory Compliance Marks ............................................................................................................ 71

x

1 Product Description

1.1

Overview

1.1.1

Feature Summary

Table 1 summarizes the major features of the board.

Table 1. Feature Summary

Form Factor

Processor

Memory

Graphics

Audio

Peripheral Interfaces

Storage

4.0 inches by 4.0 inches (101.60 millimeters by 101.60 millimeters)

• Soldered-down quad-core Intel ® Pentium ® processor N3700 with up to 6 W TDP

― Integrated graphics

― Integrated memory controller

― Integrated PCH

• 2 GB DDR3L 1600 MHz SO-DIMM pre-installed

• Support for 1066 MHz/1666 MHz memory speeds

Note: If you install 1333 MHz, it will run at 1066 MHz.

• Support for up to 8 GB of system memory with one SO-DIMM using 4 Gb memory technology

• Support for non-ECC memory

• Support for 1.35 V low voltage JEDEC memory

• Integrated graphics support with Intel

®

Graphics Technology:

― High Definition Multimedia Interface* (HDMI*)

― VGA

• Intel® High Definition (Intel ® processor

HD) Audio via the HDMI v1.4b interface through the

• Realtek HD Audio via a stereo microphone/headphone 3.5 mm jack on the front panel

• Compressed 5.1/7.1 digital audio through a Mini-TOSLINK jack on the back panel

• USB 3.0 ports:

― Two ports are implemented with external front panel connectors (one blue and one orange charging capable)

― Two ports are implemented with external back panel connectors (blue)

• USB 2.0 ports:

― Two ports via one dual-port internal 1x8 1.25 mm pitch header (white)

― One port is reserved for an M.2 2230 for the Wireless module

• Consumer Infrared (CIR)

• One SATA 6.0 Gb/s port (black)

Supports one 2.5“ SSD or HDD up to 9.5mm

• One full sized SDXC slot

• 32 GB Embedded MultiMediaCard (e·MMC) onboard storage module continued

11

Intel NUC Board NUC5PGYH Technical Product Specification

Table 1. Feature Summary (continued)

Expansion Capabilities

One M.2 Module supporting M.2 2230 cards (key type E)

BIOS

• Intel ®

BIOS resident in the Serial Peripheral Interface (SPI) Flash device

• Support for Advanced Configuration and Power Interface (ACPI), Plug and Play, and

System Management BIOS (SMBIOS)

LAN Support

Gigabit (10/100/1000 Mb/s) LAN subsystem using the Realtek* 8111HN Gigabit Ethernet

Controller

Hardware Monitor

Subsystem

Wireless

Hardware monitoring subsystem, based on an ITE IT8607D embedded controller, including:

• Voltage sense to detect out of range power supply voltages

• Thermal sense to detect out of range thermal values

• One processor fan header

• Fan sense input used to monitor fan activity

• Simple fan speed control

• Intel® Dual Band Wireless-AC 3165 module

• 2nd Gen 802.11ac, Dual Band, 1x1 Wi-Fi + Dual Mode Bluetooth* 4.0

• Maximum Transfer speed up to 433Mbps

• Supports Intel® Wireless Display (WiDi)

• Supports Intel® Smart Connect Technology

• Pre-installed in M.2 2230 slot

12

Product Description

1.1.2

Board Layout (Top)

Figure 1 shows the location of the major components on the top-side of Intel NUC Board

NUC5PGYH.

Figure 1. Major Board Components (Top)

13

Intel NUC Board NUC5PGYH Technical Product Specification

Table 2 lists the components identified in Figure 1.

Table 2. Components Shown in Figure 1

F

G

D

E

H

B

C

Item from Figure 1

A

Description

Battery

Front panel header

Thermal solution

Processor fan header

Onboard power button

Power LED

Hard Disk Drive LED

Standby Power LED

14

Product Description

1.1.3

Board Layout (Bottom)

Figure 2 shows the location of the major components on the bottom-side of Intel NUC Board

NUC5PGYH.

Figure 2. Major Board Components (Bottom)

15

Intel NUC Board NUC5PGYH Technical Product Specification

K

L

M

I

J

G

H

C

D

A

B

E

F

Table 3. Components Shown in Figure 2

Item from

Figure 2

Description

Back panel connectors

Auxiliary power connector (1.25 mm pitch)

VGA connector

M.2 2230 Module connector

SDXC slot

Front panel dual-port USB 2.0 header (1.25 mm pitch)

SATA power connector (1.25 mm pitch)

SATA 6.0 Gb/s connector

Front panel USB 3.0 connectors (one blue and one orange charging capable)

BIOS security jumper

Front panel stereo microphone/headphone jack

Front panel Consumer Infrared sensor (CIR)

DDR3L SO-DIMM socket

16

1.1.4

Block Diagram

Figure 3 is a block diagram of the major functional areas of the board.

Product Description

Figure 3. Block Diagram

17

Intel NUC Board NUC5PGYH Technical Product Specification

1.2

Online Support

To find information about… Visit this World Wide Web site:

Intel NUC Board NUC5PGYH

NUC Board Support http://www.intel.com/NUC http://www.intel.com/NUCSupport

Available configurations for Intel NUC Board NUC5PGYH http://ark.intel.com

BIOS and driver updates http://downloadcenter.intel.com

Tested memory

Integration information http://www.intel.com/NUCSupport http://www.intel.com/NUCSupport

1.3

Processor

Intel NUC Board NUC5PGYH has a soldered-down System-on-a-Chip (SoC), which consists of a quad-core Intel Pentium processor N3700 with up to 6 W TDP.

• Integrated graphics

• Integrated memory controller

• Integrated PCH

NOTE

This board has specific requirements for providing power to the processor. Refer to Section 2.5.1 on page 51 for information on power supply requirements for this board.

18

Product Description

1.4

System Memory

The board has one 204-pin SO-DIMM socket and supports the following memory features:

• Pre-installed 2 GB DDR3L 1600 MHz SDRAM SO-DIMM (1.35 V) with gold plated contacts

• Support for 1066 MHz/1666 MHz memory speeds

Note: If you install 1333 MHz, it will run at 1066 MHz.

• One memory channel

• Unbuffered, single-sided or double-sided SO-DIMMs

8 GB maximum total system memory (with 4 Gb memory technology). Refer to Section 2.1.1 on page 35 for information on the total amount of addressable memory.

• Minimum recommended total system memory: 1024 MB

• Non-ECC SO-DIMMs

• Serial Presence Detect

NOTE

To be fully compliant with all applicable DDR SDRAM memory specifications, the board should be populated with SO-DIMMs that support the Serial Presence Detect (SPD) data structure. This allows the BIOS to read the SPD data and program the chipset to accurately configure memory settings for optimum performance. If non-SPD memory is installed, the BIOS will attempt to correctly configure the memory settings, but performance and reliability may be impacted or the

SO-DIMMs may not function under the determined frequency.

Table 4 lists the supported SO-DIMM configurations.

Table 4. Supported Memory Configurations

SO-DIMM

Capacity

1024 MB

2048 MB

2048 MB

4096 MB

4096 MB

8192 MB

Configuration

SS

DS

SS

DS

SS

DS

(Note)

SDRAM

Density

1 Gbit

1 Gbit

2 Gbit

2 Gbit

4 Gbit

4 Gbit

SDRAM Organization

Front-side/Back-side

128 M x8/empty

128 M x8/128 M x8

256 M x8/empty

256 M x8/256 M x8

512 M x8/empty

512 M x8/512 M x8

Number of SDRAM

Devices

8

16

8

16

8

16

Note: “DS” refers to double-sided memory modules (containing two rows of SDRAM) and “SS” refers to single-sided memory modules (containing one row of SDRAM).

For information about… Refer to:

Tested Memory http://www.intel.com/NUCSupport

19

Intel NUC Board NUC5PGYH Technical Product Specification

Figure 4 illustrates the memory channel and SO-DIMM configuration.

Figure 4. Memory Channel and SO-DIMM Configuration

20

Product Description

1.5

Processor Graphics Subsystem

The board supports graphics through Intel HD Graphics.

1.5.1

Integrated Graphics

The board supports integrated graphics via the processor.

1.5.1.1

Intel

®

High Definition (Intel

®

HD) Graphics

The Intel HD graphics controller features the following:

• HDMI 1.4b

• 3D graphics hardware acceleration supporting DirectX*11.1, OpenCL* 1.2, OGL ES

Halti/2.0/1.1, OpenGL* 4.2

• Video decode hardware acceleration supporting H.265/HEVC @ Level 5, H.264 @ Level 5.2,

MPEG2, MVC, VC-1, WMV9, JPEG and VP8 formats

• Video encode hardware acceleration supporting H.264 @ Level 5.1, JPEG and MVC formats

• High-Bandwidth Digital Content Protection (HDCP) 1.4/2.2 support for content protection

1.5.1.2

Video Memory Allocation

Intel ® Dynamic Video Memory Technology (DVMT) is a method for dynamically allocating system memory for use as graphics memory to balance 2D/3D graphics and system performance. If your computer is configured to use DVMT, graphics memory is allocated based on system requirements and application demands (up to the configured maximum amount). When memory is no longer needed by an application, the dynamically allocated portion of memory is returned to the operating system for other uses.

1.5.1.3

High Definition Multimedia Interface* (HDMI*)

The HDMI port supports standard, enhanced, or high definition video, plus multi-channel digital audio on a single cable. The port is compatible with all ATSC and DVB HDTV standards and supports eight full range channels at 24-bit/96 kHz audio of lossless audio formats. The maximum supported resolution is 3840 x 2160 @ 30 Hz and 2560 x 1600 @ 60 Hz, 24 bpp (WUXGA). The

HDMI port is compliant with the HDMI 1.4b specification.

1.5.1.3.1

Integrated Audio Provided by the HDMI Interfaces

The following audio technologies are supported by the HDMI 1.4b interfaces directly from the

SoC:

• AC3 - Dolby* Digital

• Dolby Digital Plus

• LPCM, 192 kHz/24-bit, 8 Channel

21

Intel NUC Board NUC5PGYH Technical Product Specification

1.6

USB

The USB port arrangement is as follows:

• USB 3.0 ports (maximum current is 900 mA for each blue port, 1.5 A for the orange charging port):

 Two ports are implemented with external front panel connectors (one blue and one orange charging capable)

 Two ports are implemented with external back panel connectors (blue)

• USB 2.0 ports (maximum current is 500 mA for each port of the white header (1 A total):

 Two ports via one dual-port internal 1x8 1.25 mm pitch header (white)

 One port is reserved for an M.2 2230 for the Wireless module

All the USB ports are high-speed, full-speed, and low-speed capable.

NOTE

Computer systems that have an unshielded cable attached to a USB port may not meet FCC

Class B requirements, even if no device is attached to the cable. Use a shielded cable that meets the requirements for full-speed devices.

For information about

The location of the USB connectors on the back panel

The location of the USB connector on the front panel

Refer to

Figure 11, page 36

Figure 2, page 15

1.7

SATA Interface

The SoC provides one SATA port with a theoretical maximum transfer rate of 6.0 Gb/s. A point-topoint interface is used for host to device connections.

The underlying SATA functionality is transparent to the operating system. The SATA controller can operate in both legacy and native modes. In legacy mode, standard IDE I/O and IRQ resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering is used. Native mode is the preferred mode for configurations using Windows* operating systems.

1.7.1

AHCI Mode

The board supports AHCI storage mode.

NOTE

In order to use AHCI mode, AHCI must be enabled in the BIOS. Microsoft* Windows 8 includes the necessary AHCI drivers without the need to install separate AHCI drivers during the operating system installation process. However, it is always good practice to update the AHCI drivers to the latest available by Intel.

22

Product Description

1.8

Real-Time Clock Subsystem

A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the computer is not plugged into a wall socket, the battery has an estimated life of three years. When the computer is plugged in, the standby current from the power supply extends the life of the battery.

The clock is accurate to ± 13 minutes/year at 25 ºC with 3.3 VSB applied via the power supply 5 V

STBY rail.

NOTE

If the battery and AC power fail, date and time values will be reset and the user will be notified during the POST.

When the voltage drops below a certain level, the BIOS Setup program settings stored in CMOS

RAM (for example, the date and time) might not be accurate. Replace the battery with an

equivalent one. Figure 1 on page 13 shows the location of the battery.

23

Intel NUC Board NUC5PGYH Technical Product Specification

1.9

Audio Subsystem

The board supports Intel HD Audio via the Realtek ALC283 audio codec. The audio subsystem supports the following features:

• Analog line-out/Analog Headphone/Analog Microphone jack on the front panel

• High Definition Audio via a stereo microphone/headphone jack on the back panel

• Support for 44.1 kHz/48 kHz/96 kHz/192 kHz sample rates on all analog outputs

• Support for 44.1 kHz/48 kHz/96 kHz sample rates on all analog inputs

Back Panel Audio Jack Support (see Figure 5 for 3.5 mm audio jack pin out):

Speakers only

 Headphones only

 Microphone only

 Combo Headphone/Microphone

Pin Number

3

4

1

2

Pin Name

Tip

Ring

Ring

Sleeve

Description

Left Audio Out

Right Audio Out

Common/Ground

Audio In

Figure 5. 4-Pin 3.5 mm (1/8 inch) Audio Jack Pin Out

NOTE

The analog circuit of the back panel audio connector is designed to power headphones or amplified speakers only. Poor audio quality occurs if passive (nonamplified) speakers are connected to this output.

24

1.9.1

Mini-TOSLINK Interface

The 3.5 mm audio jack also provides TOSLINK optical digital audio output.

• Mini-TOSLINK interface (back panel) plus analog audio out

 PCM datastream support

 S/PDIF datastream support

 Mini-TOSLINK adaptor necessary to connect to standard TOSLINK cable

 Stereo audio out

Product Description

Figure 6. Mini-TOSLINK Adaptor

1.9.2

Audio Subsystem Software

Audio software and drivers are available from Intel’s World Wide Web site.

For information about Refer to

Obtaining Audio software and drivers http://downloadcenter.intel.com

25

Intel NUC Board NUC5PGYH Technical Product Specification

1.10

LAN Subsystem

The LAN subsystem consists of the following:

• Realtek 8111HN-CG Gigabit Ethernet Controller (10/100/1000 Mb/s)

• RJ-45 LAN connector with integrated status LEDs

• Intel® Dual Band Wireless-AC 3165 module

Additional features of the LAN subsystem include:

• CSMA/CD protocol engine

• Jumbo frame support 9K

• LAN connect interface between the SoC and the LAN controller

• Power management capabilities

 ACPI technology support

 LAN wake capabilities

• LAN subsystem software

For information about

LAN software and drivers

Refer to

http://downloadcenter.intel.com

1.10.1

Realtek* 8111HN Gigabit Ethernet Controller

The Realtek 8111HN Gigabit Ethernet Controller supports the following features:

• 10/100/1000 BASE-T IEEE 802.3 compliant

• Energy Efficient Ethernet (EEE) IEEE802.3az support (Low Power Idle (LPI) mode)

• Dual interconnect between the Integrated LAN Controller and the Physical Layer (PHY):

 PCI Express-based interface for active state operation (S0) state

 SMBUS for host and management traffic (Sx low power state)

• Compliant to IEEE 802.3x flow control support

• 802.1p and 802.1q

• TCP, IP, and UDP checksum offload (for IPv4 and IPv6)

• Full device driver compatibility

For information about Refer to

Full LAN Hardware feature set http://www.realtek.com.tw/

1.10.2

LAN Subsystem Software

LAN software and drivers are available from Intel’s World Wide Web site.

For information about Refer to

Obtaining LAN software and drivers http://downloadcenter.intel.com

26

1.10.3

RJ-45 LAN Connector with Integrated LEDs

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 7).

Product Description

Item

A

B

Description

Link LED (Green)

Data Rate LED (Green/Yellow)

Figure 7. LAN Connector LED Locations

Table 5 describes the LED states when the board is powered up and the LAN subsystem is operating.

Table 5. LAN Connector LED States

LED LED Color LED State

Off

Link (A)

Data Rate (B)

Green

Green/Yellow

On

Blinking

Off

Green

Yellow

Condition

LAN link is not established.

LAN link is established.

LAN activity is occurring.

10 Mb/s data rate is selected.

100 Mb/s data rate is selected.

1000 Mb/s data rate is selected.

1.10.4

Wireless Network Module

The Intel Dual Band Wireless-AC 3165 module provides hi-speed wireless connectivity with the following capabilities:

• Intel® Dual Band Wireless-AC 3165 module

• 2nd Gen 802.11ac, Dual Band, 1x1 Wi-Fi + Dual Mode Bluetooth* 4.0

• Maximum Transfer speed up to 433Mbps

• Supports Intel® Wireless Display (WiDi)

• Supports Intel® Smart Connect Technology

Pre-installed in M.2 2230 slot

For information about Refer to

Obtaining WLAN software and drivers

Full Specifications http://downloadcenter.intel.com

http://intel.com/wireless

27

Intel NUC Board NUC5PGYH Technical Product Specification

1.11

Hardware Management Subsystem

The hardware management features enable the board to be compatible with the Wired for

Management (WfM) specification. The board has several hardware management features, including thermal and voltage monitoring.

For information about

Wired for Management (WfM) Specification

Refer to

www.intel.com/design/archives/wfm/

1.11.1

Hardware Monitoring

The hardware monitoring and fan control subsystem is based on an ITE IT6515FN embedded controller, which supports the following:

• Processor and system ambient temperature monitoring

• Chassis fan speed monitoring

• Voltage monitoring of +5 V, +3.3 V, Memory Vcc (SDRAM)

• SMBus interface

1.11.2

Fan Monitoring

Fan monitoring can be implemented using third-party software.

28

1.11.3

Thermal Solution

Figure 8 shows the location of the thermal solution and processor fan header.

Product Description

Item Description

A

B

Processor fan header

Thermal solution

Figure 8. Thermal Solution and Fan Header

29

Intel NUC Board NUC5PGYH Technical Product Specification

1.12

Power Management

Power management is implemented at several levels, including:

• Software support through Advanced Configuration and Power Interface (ACPI)

• Hardware support:

 Power Input

 Instantly Available PC technology

 LAN wake capabilities

 Wake from USB

 WAKE# signal wake-up support

 Wake from S5

 Wake from CIR

 +5 V Standby Power Indicator LED

1.12.1

ACPI

ACPI gives the operating system direct control over the power management and Plug and Play functions of a computer. The use of ACPI with this board requires an operating system that provides full ACPI support. ACPI features include:

• Plug and Play (including bus and device enumeration)

• Power management control of individual devices, add-in boards (some add-in boards may require an ACPI-aware driver), video displays, and disk drives

• Methods for achieving less than 15-watt system operation in the power-on/standby sleeping state

• A Soft-off feature that enables the operating system to power-off the computer

Support for multiple wake-up events (see Table 8 on page 32)

• Support for a front panel power and sleep mode switch

Table 6 lists the system states based on how long the power switch is pressed, depending on how

ACPI is configured with an ACPI-aware operating system.

Table 6. Effects of Pressing the Power Switch

If the system is in this state…

Off

(ACPI G2/G5 – Soft off)

On

(ACPI G0 – working state)

On

(ACPI G0 – working state)

Sleep

(ACPI G1 – sleeping state)

Sleep

(ACPI G1 – sleeping state)

…and the power switch is pressed for

Less than four seconds

Less than four seconds

More than six seconds

Less than four seconds

More than six seconds

Note: Depending on power management settings in the operating system.

…the system enters this state

Power-on

(ACPI G0 – working state)

Soft-off/Standby

(ACPI G1 – sleeping state)

Note

Fail safe power-off

(ACPI G2/G5 – Soft off)

Wake-up

(ACPI G0 – working state)

Power-off

(ACPI G2/G5 – Soft off)

30

Product Description

1.12.1.1

System States and Power States

Under ACPI, the operating system directs all system and device power state transitions. The operating system puts devices in and out of low-power states based on user preferences and knowledge of how devices are being used by applications. Devices that are not being used can be turned off. The operating system uses information from applications and user settings to put the system as a whole into a low-power state.

Table 7 lists the power states supported by the board along with the associated system power

targets. See the ACPI specification for a complete description of the various system and power states.

Table 7. Power States and Targeted System Power

Global States

G0 – working state

G1 – sleeping state

Sleeping States

S0 – working

Processor

States

C0 – working

Device States

Targeted System

Power

(Note 1)

D0 – working state. Full power

G1 – sleeping state

S3 – Suspend to RAM.

Context saved to

RAM.

S4 – Suspend to disk.

Context saved to disk.

No power

No power

D3 – no power except for wake-up logic.

D3 – no power except for wake-up logic.

Power < 5 W

Power < 5 W

(Note 2)

(Note 2)

G2/S5

G3 – mechanical off

AC power is disconnected from the computer.

S5 – Soft off. Context not saved. Cold boot is required.

No power to the system.

No power

No power

D3 – no power except for wake-up logic.

D3 – no power for wake-up logic, except when provided by battery or external source.

Power < 5 W

(Note 2)

No power to the system.

Service can be performed safely.

Notes:

1.

Total system power is dependent on the system configuration, including add-in boards and peripherals powered by the system chassis’ power supply.

2.

Dependent on the standby power consumption of wake-up devices used in the system.

31

Intel NUC Board NUC5PGYH Technical Product Specification

1.12.1.2

Wake-up Devices and Events

Table 8 lists the devices or specific events that can wake the computer from specific states.

Table 8. Wake-up Devices and Events

Devices/events that wake up the system… …from this sleep state

Power switch

RTC alarm

LAN

S3, S4, S5

S3, S4, S5

(Note 1)

S3, S4, S5

(Notes 1, 2)

Comments

Monitor to remain in sleep state

“S5 WOL after G3” must be supported; monitor to remain in sleep state

USB

PCIe via WAKE#

Consumer IR

Bluetooth

S3, S4, S5

S3, S4, S5

S3, S4, S5

N/A

(Note 3, 4)

(Note 1)

(Notes 3, 4)

Wake S4, S5 controlled by BIOS option

Via WAKE; monitor to remain in sleep state

Wake from Bluetooth is not supported

Notes:

1.

Monitor will remain in “sleep” state

2.

“S5 WoL after G3” supported w/Deep Sleep disabled

3.

Wake from S4 and S5 only supported w/Deep Sleep disabled

4.

Wake from device/event not supported immediately upon return from AC loss

NOTE

The use of these wake-up events from an ACPI state requires an operating system that provides full ACPI support. In addition, software, drivers, and peripherals must fully support ACPI wake events.

1.12.2

Hardware Support

The board provides several power management hardware features, including:

• Wake from Power Button signal

• Instantly Available PC technology

• LAN wake capabilities

• Wake from USB

• WAKE# signal wake-up support

• Wake from S5

• Wake from CIR

• +5 V Standby Power Indicator LED

NOTE

The use of Wake from USB from an ACPI state requires an operating system that provides full ACPI support.

32

Product Description

1.12.2.1

Power Input

When resuming from an AC power failure, the computer may return to the power state it was in before power was interrupted (on or off). The computer’s response can be set using the Last

Power State feature in the BIOS Setup program’s Boot menu.

1.12.2.2

Instantly Available PC Technology

Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep-state. While in the S3 sleep-state, the computer will appear to be off (the power supply is off, and the front panel LED is amber if dual colored, or off if single colored.) When signaled by a

wake-up device or event, the system quickly returns to its last known wake state. Table 8 on page 32 lists the devices and events that can wake the computer from the S3 state.

The use of Instantly Available PC technology requires operating system support and drivers for any installed PCI Express add-in card.

1.12.2.3

LAN Wake Capabilities

LAN wake capabilities enable remote wake-up of the computer through a network. The LAN subsystem monitors network traffic at the Media Independent Interface. Upon detecting a Magic

Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer.

1.12.2.4

Wake from USB

USB bus activity wakes the computer from an ACPI S3, S4, and S5 states.

NOTE

Wake from USB requires the use of a USB peripheral that supports Wake from USB.

1.12.2.5

WAKE# Signal Wake-up Support

When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S3,

S4, or S5 state.

1.12.2.6

Wake from S5

When the RTC Date and Time is set in the BIOS, the computer will automatically wake from an

ACPI S5 state.

1.12.2.7

Wake from Consumer IR

CIR activity wakes the computer from an ACPI S3, S4, or S5 state.

1.12.2.8

+5 V Standby Power Indicator LED

The standby power indicator LED shows that power is still present even when the computer appears to be off. Figure 9 shows the location of the standby power LED.

33

Intel NUC Board NUC5PGYH Technical Product Specification

CAUTION

If AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices.

34

Figure 9. Location of the Standby Power LED

2 Technical Reference

2.1

Memory Resources

2.1.1

Addressable Memory

The board utilizes up to 8 GB of addressable system memory. Typically the address space that is allocated for PCI Conventional bus add-in cards, PCI Express configuration space, BIOS (SPI Flash device), and chipset overhead resides above the top of DRAM (total system memory). On a system that has 8 GB of system memory installed, it is not possible to use all of the installed memory due to system address space being allocated for other system critical functions. These functions include the following:

• BIOS/SPI Flash device (64 Mbit)

• Local APIC (19 MB)

• Direct Media Interface (40 MB)

• PCI Express configuration space (256 MB)

• SoC base address registers PCI Express ports (up to 256 MB)

• Memory-mapped I/O (I/O fabric) that is dynamically allocated for PCI Express add-in cards

(256 MB)

The board provides the capability to reclaim the physical memory overlapped by the memory mapped I/O logical address space. The board remaps physical memory from the top of usable

DRAM boundary to the 4 GB boundary to an equivalent sized logical address range located just above the 4 GB boundary. All installed system memory can be used when there is no overlap of system addresses.

2.2

Connectors and Headers

CAUTION

Only the following connectors and headers have overcurrent protection: back panel and front panel USB.

This section describes the board’s connectors and headers. The connectors and headers can be divided into these groups:

• Front panel I/O connector

• Back panel I/O connectors

35

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.1

Front Panel Connectors

Figure 10 shows the location of the front panel connectors for the board.

Item

A

B

C

Description

CIR

Front panel Stereo microphone/headphone jack

USB 3.0 ports (one blue and one orange charging capable)

Figure 10. Front Panel Connectors

2.2.2

Back Panel Connectors

Figure 11 shows the location of the back panel connectors for the board.

Item Description

A

B

C

D

E

USB 3.0 ports

LAN

HDMI connector

Back panel TOSLINK stereo

12 - 19V DC input jack

Figure 11. Back Panel Connectors

36

Technical Reference

2.2.3

Headers and Connectors (Top)

Figure 12 shows the location of the headers and connectors on the top-side of the board.

Figure 12. Headers and Connectors (Top)

Table 9 lists the headers and connectors identified in Figure 12.

Table 9. Headers and Connectors Shown in Figure 12

Item from Figure 12

A

B

Description

Front panel header

Processor fan header

37

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.4

Connectors and Headers (Bottom)

Figure 13 shows the locations of the connectors and headers on the bottom-side of the board.

Figure 13. Connectors and Headers (Bottom)

38

Table 10 lists the connectors and headers identified in Figure 13.

F

G

D

E

H

A

B

C

Table 10. Connectors and Headers Shown in Figure 13

Item from

Figure 13

Description

Auxiliary power connector (1.25 mm pitch)

VGA connector

M.2 2230 Module connector

SDXC slot

Front panel dual-port USB 2.0 header (1.25 mm pitch)

SATA power connector (1.25 mm pitch)

SATA 6.0 Gb/s connector

BIOS security jumper

Technical Reference

39

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.4.1

Signal Tables for the Connectors and Headers

Table 11. VGA Header

Pin

5

7

1

3

9

11

Signal Name

CLK

VCC

HSYNC

RED

GREEN

BLUE

Pin

6

8

2

4

10

12

Signal Name

DATA

VSYNC

GND

GND

GND

KEY

Table 12. SATA Power Header (1.25 mm Pitch)

3

4

5

Pin

1

2

Signal Name

5 V

5 V

3.3 V

GND

GND

NOTE

Connector is Molex* part number 53398-0571, 1.25 mm pitch PicoBlade* header, surface mount, vertical, lead-free, 5 circuits.

Table 13. Dual-Port Internal USB 2.0 Header (1.25 mm Pitch)

Pin

1

3

5

7

Signal Name

+5 V DC

Data (positive)

Ground

Data (negative)

Pin

2

4

6

8

Signal Name

Data (negative)

Ground

Data (positive)

+5 V DC

NOTE

Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface mount, vertical, lead-free, 8 circuits.

40

Signal Name

3.3V

3.3V

RESERVED

RESERVED

RESERVED

RESERVED

ALERT# (I)(0/3.3)

RESERVED

Connector Key

Connector Key

Connector Key

Connector Key

RESERVED

RESERVED

GND

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

3.3V

3.3V

I2C CLK (O)(0/3.3)

I2C DATA (I/O)(0/3.3)

W_DISABLE1# (O)(0/3.3V)

W_DISABLE2# (O)(0/3.3V)

PERST0# (O)(0/3.3V)

SUSCLK(32kHz) (O)(0/3.3V)

RESERVED

RESERVED

RESERVED

C-Link CLK (I/O)

C-Link DATA (I/O)

C-Link RESET (I) (0/3.3V)

RESERVED

RESERVED

Table 14. M.2 2230 Module (Mechanical Key E) Connector

10

8

6

18

16

14

12

4

2

24

22

20

32

30

28

26

38

36

34

46

44

42

40

52

50

48

60

58

56

54

Pin

66

64

62

74

72

70

68

11

9

7

19

17

15

13

5

3

1

25

23

21

33

31

29

27

39

37

35

47

45

43

41

53

51

49

61

59

57

55

Pin

67

65

63

75

73

71

69

Signal Name

GND

RESERVED

RESERVED

GND

RESERVED

RESERVED

GND

GND

Connector Key

Connector Key

Connector Key

Connector Key

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

RESERVED

GND

USB_D-

USB_D+

GND

RESERVED

RESERVED

GND

PEWAKE0# (I/O)(0/3.3V)

CLKREQ0# (I/O)(0/3.3V)

GND

REFCLKN0

REFCLKP0

GND

PERn0

PERp0

GND

PETn0

PETp0

Technical Reference

41

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.4.2

Add-in Card Connector

The board supports a M.2 2230 (key type E) module.

• Supports M.2 communication module

2.2.4.3

SDXC Card Reader

The board has a standard Secure Digital (SD) card reader that supports the Secure Digital eXtended Capacity (SDXC) format, 3.01 specification.

Table 15. SDXC Card Reader Connector

Pin

1

Signal Name

CD

8

9

6

7

4

5

2

3

10

11

DATA2

DATA3

CMD

VSS1

VDD

CLK

VSS2

DATA0

DATA1

WP

Descriptive Name

Card Detection

Serial Data 2

Serial Data 3

Command

Ground

Power (3.3 V)

Serial Clock

Ground

Serial Data 0

Serial Data 1

Write Protect

NOTE

The SD card reader is not supported in Microsoft* Windows* 7

42

Technical Reference

2.2.4.4

Power Supply Connector

The board has the following power supply connector:

External Power Supply – the board can be powered through a 12-19 V DC connector on the back panel. The back panel DC connector is compatible with a 5.5 mm/OD (outer diameter) and 2.5 mm/ID (inner diameter) plug, where the inner contact is +12 (±10%) V DC and the shell is GND. The maximum current rating is 3 A.

NOTE

External power voltage, 12-19 V DC, is dependent on the type of power brick used.

Table 16. Auxiliary Power Connector

Pin

3

4

1

2

Signal Name

+5VSB

PCH_GPIO24

GND

+VIN

Descriptive Name

5V

Power draw sensor

Ground

12V – 19V DC input

NOTE

The Auxiliary Power Connector is a limited voltage source (output) for 5V Standby and the voltage supplied to the board (typically 19V DC) for use by expansion peripherals. The Auxiliary Power

Connector is limited to 1.5A max (fused).

NOTE

JTE (JOINT TECH): A1250WV-S-04P A-Series (Wire to Board) Vertical SMT Connector, 1.25mm pitch, 1A rating. Mates with JTE A1250 Series Housing.

For information about

Power supply considerations

Refer to

Section 2.5.1, page 51

43

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.4.5

Front Panel Header (2.0 mm Pitch)

This section describes the functions of the front panel header. Table 17 lists the signal names of the front panel header. Figure 14 is a connection diagram for the front panel header.

Table 17. Front Panel Header (2.0 mm Pitch)

3

5

7

9

Pin Signal Name

1 HDD_POWER_LED

HDD_LED#

GROUND

RESET_SWITCH#

+5V_DC

Description

Pull-up resistor (750 Ω) to +5V

[Out] Hard disk activity

LED

Ground

[In] Reset switch

Power (2A)

Pin Signal Name

2 POWER_LED_MAIN

4

6

8

10

POWER_LED_ALT

POWER_SWITCH#

GROUND

Key

Description

[Out] Front panel LED (main color)

[Out] Front panel LED (alt color)

[In] Power switch

Ground

No pin

Figure 14. Connection Diagram for Front Panel Header (2.0 mm Pitch)

2.2.4.5.1

Hard Drive Activity LED Header

Pins 1 and 3 can be connected to an LED to provide a visual indicator that data is being read from or written to a hard drive. Proper LED function requires a SATA hard drive or optical drive connected to an onboard SATA connector.

2.2.4.5.2

Reset Switch Header

Pins 5 and 7 can be connected to a momentary single pole, single throw (SPST) type switch that is normally open. When the switch is closed, the board resets and runs the POST.

44

Technical Reference

2.2.4.5.3

Power/Sleep LED Header

Pins 2 and 4 can be connected to a one- or two-color LED. Table 18 and Table 19 show the

possible LED states.

Table 18. States for a One-Color Power LED

LED State

Off

Blinking

Steady

Description

Power off

Standby

Normal operation

Table 19. States for a Dual-Color Power LED

LED State Description

Off

Secondary color blinking

(amber)

Power off

Standby

Primary color steady (white) Normal operation

NOTE

The LED behavior shown in Table 18 is default – other patterns may be set via BIOS setup.

2.2.4.5.4

Power Switch Header

Pins 6 and 8 can be connected to a front panel momentary-contact power switch. The switch must pull the SW_ON# pin to ground for at least 50 ms to signal the power supply to switch on or off. (The time requirement is due to internal debounce circuitry on the board.) At least two seconds must pass before the power supply will recognize another on/off signal.

2.2.4.5.5

5V DC Power Header

Pin 6 can supply 2A of 5V DC (VCC) power. Any usage of power from this header should be considered when calculating the system’s total power budget.

For information about

Power supply considerations

Refer to

Section 2.5.1, page 51

45

Intel NUC Board NUC5PGYH Technical Product Specification

2.2.4.6

Consumer Infrared (CIR) Sensor

The Consumer Infrared (CIR) sensor on the front panel provides features that are designed to comply with Microsoft Consumer Infrared usage models.

The CIR feature is made up of the receiving sensor. The receiving sensor consists of a filtered translated infrared input compliant with Microsoft CIR specifications.

Customers are required to provide their own media center compatible remote or smart phone

application for use with the Intel NUC. Figure 15 shows the location of the CIR sensor.

Item Description

A CIR Sensor

Figure 15. Location of the CIR Sensor

46

Technical Reference

2.2.4.7

Internal USB 2.0 Dual-Port Header (1.25 mm Pitch)

Figure 16 is a connection diagram for the internal USB header.

Connector is Molex part number 53398-0571, 1.25 mm pitch PicoBlade header, surface mount, vertical, lead-free, 8 circuits.

NOTE

The +5 V DC power on the USB header is fused.

Use only an internal USB connector that conforms to the USB 2.0 specification for high-speed

USB devices.

Figure 16. Connection Diagram for Internal

USB 2.0 Dual-Port Header (1.25 mm Pitch)

47

Intel NUC Board NUC5PGYH Technical Product Specification

2.3

BIOS Security Jumper

CAUTION

Do not move a jumper with the power on. Always turn off the power and unplug the power cord from the computer before changing a jumper setting. Otherwise, the board could be damaged.

Figure 17 shows the location of the BIOS security jumper. The 3-pin jumper determines the BIOS

Security program’s mode. Table 20 describes the BIOS security jumper settings for the three

modes: normal, lockdown, and configuration.

Figure 17. Location of the BIOS Security Jumper

48

Technical Reference

Table 20 lists the settings for the jumper.

Table 20. BIOS Security Jumper Settings

Function/Mode

Normal

Lockdown

Jumper Setting

1-2

2-3

Configuration

The BIOS uses current configuration information and passwords for booting.

The BIOS uses current configuration information and passwords for booting, except:

• All POST Hotkeys are suppressed (prompts are not displayed and keys are not accepted. For example, F2 for Setup, F10 for the Boot Menu).

• Power Button Menu is not available (see Section 3.7.4 Power Button

Menu).

BIOS updates are not available except for automatic Recovery due to flash corruption.

Configuration None BIOS Recovery Update process if a matching *.bio file is found. Recovery

Update can be cancelled by pressing the Esc key.

If the Recovery Update was cancelled or a matching *.bio file was not found, a Config Menu will be displayed. The Config Menu consists of the following (followed by the Power Button Menu selections):

[1] Suppress this menu until the BIOS Security Jumper is replaced.

[2] Clear BIOS User and Supervisor Passwords.

See Section 3.7.4 Power Button Menu.

49

Intel NUC Board NUC5PGYH Technical Product Specification

2.4

Mechanical Considerations

2.4.1

Form Factor

The board is designed to fit into a custom chassis. Figure 18 illustrates the mechanical form factor

for the board. Dimensions are given in millimeters. The outer dimensions are 101.60 millimeters by 101.60 millimeters [4.0 inches by 4.0 inches].

Figure 18. Board Dimensions

50

Technical Reference

Figure 19 shows the height dimensions of the board.

Figure 19. Board Height Dimensions

2.5

Electrical Considerations

2.5.1

Power Supply Considerations

System power requirements will depend on actual system configurations chosen by the integrator, as well as end user expansion preferences. It is the system integrator’s responsibility to ensure an appropriate power budget for the system configuration is properly assessed based on the system-level components chosen.

2.5.2

Fan Header Current Capability

Table 21 lists the current capability of the fan header.

Table 21. Fan Header Current Capability

Fan Header

Processor fan

Maximum Available Current

.25 A

2.6

Thermal Considerations

CAUTION

A chassis with a maximum internal ambient temperature of 58

o

C at the processor fan inlet is recommended. If the internal ambient temperature exceeds 58

o

C, further thermal testing is required to ensure components do not exceed their maximum case temperature.

CAUTION

Failure to ensure appropriate airflow may result in reduced performance of both the processor and/or voltage regulator or, in some instances, damage to the board.

All responsibility for determining the adequacy of any thermal or system design remains solely with the system integrator. Intel makes no warranties or representations that merely following the

instructions presented in this document will result in a system with adequate thermal performance.

51

Intel NUC Board NUC5PGYH Technical Product Specification

CAUTION

Ensure that the ambient temperature does not exceed the board’s maximum operating temperature. Failure to do so could cause components to exceed their maximum case temperature and malfunction. For information about the maximum operating temperature, see

the environmental specifications in Section 2.8.

CAUTION

The processor voltage regulator area (shown in Figure 20) can reach a temperature of up to

97.5

o

C in an open chassis. Ensure that proper airflow is maintained in the processor voltage regulator circuit. Failure to do so may result in shorter than expected product lifetime.

Figure 20 shows the locations of the localized high temperature zones.

52

Item

A

B

Description

Processor voltage regulator area

Thermal solution

Figure 20. Localized High Temperature Zones

Technical Reference

Table 22 provides maximum case temperatures for the components that are sensitive to thermal

changes. The operating temperature, current load, or operating frequency could affect case temperatures. Maximum case temperatures are important when considering proper airflow to cool the board.

Table 22. Thermal Considerations for Components

Component

Processor

Maximum Case Temperature

For processor case temperature, see processor datasheets and processor specification updates

To ensure functionality and reliability, the component is specified for proper operation when Case

Temperature is maintained at or below the maximum temperature listed in Table 23. This is a

requirement for sustained power dissipation equal to Thermal Design Power (TDP is specified as the maximum sustainable power to be dissipated by the components). When the component is dissipating less than TDP, the case temperature should be below the Maximum Case

Temperature. The surface temperature at the geometric center of the component corresponds to

Case Temperature.

It is important to note that the temperature measurement in the system BIOS is a value reported by embedded thermal sensors in the components and does not directly correspond to the

Maximum Case Temperature. The upper operating limit when monitoring this thermal sensor is

Tcontrol.

Table 23. Tcontrol Values for Components

Component

Processor

Tcontrol

For processor case temperature, see processor datasheets and processor specification updates

For information about

Processor datasheets and specification updates

Refer to

Section 1.2, page 18

53

Intel NUC Board NUC5PGYH Technical Product Specification

2.7

Reliability

The Mean Time Between Failures (MTBF) prediction is calculated using component and subassembly random failure rates. The calculation is based on the Telcordia SR-332-2 Issue 2,

Method I, Case 3, 55 ºC ambient. The MTBF prediction is used to estimate repair rates and spare parts requirements. The MTBF for the board is 64,688 hours.

2.8

Environmental

Table 24 lists the environmental specifications for the board.

Table 24. Environmental Specifications

Parameter

Temperature

Non-Operating

Operating

Shock

Unpackaged

Packaged

Vibration

Unpackaged

Packaged

Specification

-40 °C to +60 °C

0 °C to +40 °C

The operating temperature of the board may be determined by measuring the air temperature from the junction of the heatsink fins and fan, next to the attachment screw, in a closed chassis, while the system is in operation.

50 g trapezoidal waveform

Velocity change of 170 inches/s²

Half sine 2 millisecond

Product Weight (pounds)

<20

21-40

41-80

81-100

Free Fall (inches)

36

30

24

18

Velocity Change (inches/s²)

167

152

136

118

5 Hz to 20 Hz: 0.01 g² Hz sloping up to 0.02 g² Hz

20 Hz to 500 Hz: 0.02 g² Hz (flat)

5 Hz to 40 Hz: 0.015 g² Hz (flat)

40 Hz to 500 Hz: 0.015 g² Hz sloping down to 0.00015 g² Hz

Note: Before attempting to operate this board, the overall temperature of the board must be above the minimum operating temperature specified. It is recommended that the board temperature be at least room temperature before attempting to power on the board. The operating and non-operating environment must avoid condensing humidity.

54

3 Overview of BIOS Features

3.1

Introduction

The board uses an Intel Visual BIOS that is stored in the Serial Peripheral Interface Flash Memory

(SPI Flash) and can be updated using a disk-based program. The SPI Flash contains the Visual

BIOS Setup program, POST, the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support. The initial production BIOSs are identified as PYBSWCEL.86A.

The Visual BIOS Setup program can be used to view and change the BIOS settings for the computer, and to update the system BIOS. The BIOS Setup program is accessed by pressing the

<F2> key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins.

NOTE

The maintenance menu is displayed only when the board is in configuration mode. Section 2.3 on page 48 shows how to put the board in configuration mode.

3.2

BIOS Flash Memory Organization

The Serial Peripheral Interface Flash Memory (SPI Flash) includes a 64 Mb (8192 KB) flash memory device.

3.3

System Management BIOS (SMBIOS)

SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network.

The main component of SMBIOS is the Management Information Format (MIF) database, which contains information about the computing system and its components. Using SMBIOS, a system administrator can obtain the system types, capabilities, operational status, and installation dates for system components. The MIF database defines the data and provides the method for accessing this information. The BIOS enables applications such as third-party management software to use SMBIOS. The BIOS stores and reports the following SMBIOS information:

• BIOS data, such as the BIOS revision level

• Fixed-system data, such as peripherals, serial numbers, and asset tags

• Resource data, such as memory size, cache size, and processor speed

• Dynamic data, such as event detection and error logging

Non-Plug and Play operating systems require an additional interface for obtaining the SMBIOS information. The BIOS supports an SMBIOS table interface for such operating systems. Using this support, an SMBIOS service-level application running on a non-Plug and Play operating system can obtain the SMBIOS information. Additional board information can be found in the BIOS under the Additional Information header under the Main BIOS page.

55

Intel NUC Board NUC5PGYH Technical Product Specification

3.4

Legacy USB Support

Legacy USB support enables USB devices to be used even when the operating system’s USB drivers are not yet available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB support is set to

Enabled.

Legacy USB support operates as follows:

1.

When you apply power to the computer, legacy support is disabled.

2.

POST begins.

3.

Legacy USB support is enabled by the BIOS allowing you to use a USB keyboard to enter and configure the BIOS Setup program and the maintenance menu.

4.

POST completes.

5.

The operating system loads. While the operating system is loading, USB keyboards and mice are recognized and may be used to configure the operating system. (Keyboards and mice are not recognized during this period if Legacy USB support was set to Disabled in the BIOS Setup program.)

6.

After the operating system loads the USB drivers, all legacy and non-legacy USB devices are recognized by the operating system, and Legacy USB support from the BIOS is no longer used.

7.

Additional USB legacy feature options can be access by using Intel ®

Integrator Toolkit.

To install an operating system that supports USB, verify that Legacy USB support in the BIOS

Setup program is set to Enabled and follow the operating system’s installation instructions.

3.5

BIOS Updates

The BIOS can be updated using either of the following utilities, which are available on the Intel

World Wide Web site:

• Intel ®

Express BIOS Update utility, which enables automated updating while in the Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM, or from the file location on the Web.

• Intel

® Flash Memory Update Utility, which requires booting from DOS. Using this utility, the

BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM.

• Intel

F7 switch during POST allows a user to select where the BIOS .bio file is located and perform the update from that location/device. Similar to performing a BIOS Recovery without removing the BIOS configuration jumper.

• Intel Visual BIOS allows the user to select the BIOS .bio file from the internet, USB device, hard disk drive, or other media.

All utilities verify that the updated BIOS matches the target system to prevent accidentally installing an incompatible BIOS.

NOTE

Review the instructions distributed with the upgrade utility before attempting a BIOS update.

56

Overview of BIOS Features

For information about

BIOS update utilities

Refer to

http://www.intel.com/support/motherboards/desktop/sb/CS-

034499.htm

3.5.1

Language Support

The BIOS Setup program and help messages are supported in US English. Check the Intel web site for support.

3.5.2

Custom Splash Screen

During POST, an Intel ® splash screen is displayed by default. This splash screen can be augmented with a custom splash screen. The Intel Integrator’s Toolkit that is available from Intel can be used to create a custom splash screen.

NOTE

If you add a custom splash screen, it will share space with the Intel branded logo.

For information about

Intel Integrator Toolkit

Additional Intel

®

software tools

Refer to

http://developer.intel.com/design/motherbd/software/itk/ http://developer.intel.com/design/motherbd/software.htm

57

Intel NUC Board NUC5PGYH Technical Product Specification

3.6

BIOS Recovery

It is unlikely that anything will interrupt a BIOS update; however, if an interruption occurs, the

BIOS could be damaged. Table 25 lists the drives and media types that can and cannot be used

for BIOS recovery. The BIOS recovery media does not need to be made bootable.

Table 25. Acceptable Drives/Media Types for BIOS Recovery

Media Type

(Note)

Hard disk drive (connected to SATA or USB)

CD/DVD drive (connected to SATA or USB)

USB flash drive

USB diskette drive (with a 1.4 MB diskette)

Can be used for BIOS recovery?

Yes

Yes

Yes

No (BIOS update file is bigger than 1.4 MB size limit)

NOTE

Supported file systems for BIOS recovery:

NTFS (sparse, compressed, or encrypted files are not supported)

FAT32

FAT16

FAT12

ISO 9660

For information about

BIOS recovery

Refer to

http://www.intel.com/support/motherboards/desktop/sb/CS-034524.htm

58

Overview of BIOS Features

3.7

Boot Options

In the BIOS Setup program, the user can choose to boot from a hard drive, optical drive, removable drive, or the network. The default setting is for the optical drive to be the first boot device, the hard drive second, removable drive third, and the network fourth.

3.7.1

Network Boot

The network can be selected as a boot device. This selection allows booting from the onboard

LAN or a network add-in card with a remote boot ROM installed.

Pressing the <F12> key during POST automatically forces booting from the LAN. To use this key during POST, the User Access Level in the BIOS Setup program's Security menu must be set to Full.

3.7.2

Booting Without Attached Devices

For use in embedded applications, the BIOS has been designed so that after passing the POST, the operating system loader is invoked even if the following devices are not present:

• Video adapter

• Keyboard

• Mouse

3.7.3

Changing the Default Boot Device During POST

Pressing the <F10> key during POST causes a boot device menu to be displayed. This menu

displays the list of available boot devices. Table 26 lists the boot device menu options.

Table 26. Boot Device Menu Options

Boot Device Menu Function Keys

<↑> or <↓>

<Enter>

<Esc>

Description

Selects a default boot device

Exits the menu, and boots from the selected device

Exits the menu and boots according to the boot priority defined through BIOS setup

59

Intel NUC Board NUC5PGYH Technical Product Specification

3.7.4

Power Button Menu

The Power Button Menu is accessible via the following sequence:

1.

System is in S4/S5 (not G3)

2.

User pushes the power button and holds it down

3.

The system will emit three short beeps from the PC speaker or headphones, if installed, then stop to signal the user to release the power button (approximately 3 seconds) or the power button LED to its alternate color. Release immediately.

4.

User releases the power button before the 4-second shutdown override

If this boot path is taken, the BIOS will use default settings, ignoring settings in VPD where possible.

At the point where Setup Entry/Boot would be in the normal boot path, the BIOS will display the following prompt and wait for a keystroke:

[ESC] Normal Boot

[F2] Intel Visual BIOS

[F3] Disable Fast Boot

[F4] BIOS Recovery

[F7] Update BIOS

[F10] Enter Boot Menu

[F12] Network Boot

[F3] Disable Fast Boot is only displayed if at least one Fast Boot optimization is enabled.

If an unrecognized key is hit, then the BIOS will beep and wait for another keystroke. If one of the listed hotkeys is hit, the BIOS will follow the indicated boot path. Password requirements must still be honored.

If Disable Fast Boot is selected, the BIOS will disable all Fast Boot optimizations and reset the system.

60

Overview of BIOS Features

3.8

Hard Disk Drive Password Security Feature

The Hard Disk Drive Password Security feature blocks read and write accesses to the hard disk drive until the correct password is given. Hard Disk Drive Passwords are set in BIOS SETUP and are prompted for during BIOS POST. For convenient support of S3 resume, the system BIOS will automatically unlock drives on resume from S3. Valid password characters are A-Z, a-z, and 0-9.

Passwords may be up to 20 characters in length.

The User hard disk drive password, when installed, will be required upon each power-cycle until the Master Key or User hard disk drive password is submitted.

The Master Key hard disk drive password, when installed, will not lock the drive. The Master Key hard disk drive password exists as an unlock override in the event that the User hard disk drive password is forgotten. Only the installation of the User hard disk drive password will cause a hard disk to be locked upon a system power-cycle.

Table 27 shows the effects of setting the Hard Disk Drive Passwords.

Table 27. Master Key and User Hard Drive Password Functions

Password Set

Neither

Master only

User only

Master and User Set

Password During Boot

None

None

User only

Master or User

During every POST, if a User hard disk drive password is set, POST execution will pause with the following prompt to force the user to enter the Master Key or User hard disk drive password:

Enter Hard Disk Drive Password:

Upon successful entry of the Master Key or User hard disk drive password, the system will continue with normal POST.

If the hard disk drive password is not correctly entered, the system will go back to the above prompt. The user will have three attempts to correctly enter the hard disk drive password. After the third unsuccessful hard disk drive password attempt, the system will halt with the message:

Hard Disk Drive Password Entry Error

A manual power cycle will be required to resume system operation.

NOTE

The passwords are stored on the hard disk drive so if the drive is relocated to another computer that does not support Hard Disk Drive Password Security feature, the drive will not be accessible.

61

Intel NUC Board NUC5PGYH Technical Product Specification

3.9

BIOS Security Features

The BIOS includes security features that restrict access to the BIOS Setup program and who can boot the computer. A supervisor password and a user password can be set for the BIOS Setup program and for booting the computer, with the following restrictions:

• The supervisor password gives unrestricted access to view and change all the Setup options in the BIOS Setup program. This is the supervisor mode.

• The user password gives restricted access to view and change Setup options in the BIOS

Setup program. This is the user mode.

• If only the supervisor password is set, pressing the <Enter> key at the password prompt of the

BIOS Setup program allows the user restricted access to Setup.

• If both the supervisor and user passwords are set, users can enter either the supervisor password or the user password to access Setup. Users have access to Setup respective to which password is entered.

• Setting the user password restricts who can boot the computer. The password prompt will be displayed before the computer is booted. If only the supervisor password is set, the computer boots without asking for a password. If both passwords are set, the user can enter either password to boot the computer.

• For enhanced security, use different passwords for the supervisor and user passwords.

• Valid password characters are A-Z, a-z, and 0-9. Passwords may be up to 20 characters in length.

• To clear a set password, enter a blank password after entering the existing password.

Table 28 shows the effects of setting the supervisor password and user password. This table is

for reference only and is not displayed on the screen.

Table 28. Supervisor and User Password Functions

Password Set Supervisor Mode

Neither Can change all options

(Note)

Supervisor only Can change all options

User only

Supervisor and user set

N/A

Can change all options

User Mode

Can change all options

(Note)

Can change a limited number of options

Can change all options

Can change a limited number of options

Setup Options

None

Enter Password

Clear User Password

Supervisor Password

Enter Password

Password to

Enter Setup

None

Supervisor Password Supervisor

User

Supervisor or user

Note: If no password is set, any user can change all Setup options.

Password

During Boot

None

None

User

Supervisor or user

62

4 Error Messages and Blink Codes

4.1

Front-panel Power LED Blink Codes

Whenever a recoverable error occurs during POST, the BIOS causes the board’s front panel power

LED to blink an error message describing the problem (see Table 29).

Table 29. Front-panel Power LED Blink Codes

Type

BIOS update in progress

Video error

(Note)

Memory error

Thermal trip warning

Pattern

Off when the update begins, then on for 0.5 seconds, then off for 0.5 seconds. The pattern repeats until the

BIOS update is complete.

On-off (1.0 second each) two times, then 2.5-second pause (off), entire pattern repeats (blink and pause) until the system is powered off.

On-off (1.0 second each) three times, then 2.5-second pause (off), entire pattern repeats (blinks and pause) until the system is powered off.

Each beep will be accompanied by the following blink pattern: .25 seconds on, .25 seconds off,

.25 seconds on, .25 seconds off. This will result in a total of 16 blinks.

Note: Disabled per default BIOS setup option.

Note

When no VGA option ROM is found.

4.2

BIOS Error Messages

Table 30 lists the error messages and provides a brief description of each.

Table 30. BIOS Error Messages

Error Message

CMOS Battery Low

CMOS Checksum Bad

Memory Size Decreased

No Boot Device Available

Explanation

The battery may be losing power. Replace the battery soon.

The CMOS checksum is incorrect. CMOS memory may have been corrupted. Run Setup to reset values.

Memory size has decreased since the last boot. If no memory was removed, then memory may be bad.

System did not find a device to boot.

63

Intel NUC Board NUC5PGYH Technical Product Specification

64

5 Regulatory Compliance and Battery

Disposal Information

5.1

Regulatory Compliance

This section contains the following regulatory compliance information for Intel NUC Board

NUC5PGYH:

• Safety standards

• European Union Declaration of Conformity statement

• Product Ecology statements

• Electromagnetic Compatibility (EMC) standards

• Product certification markings

5.1.1

Safety Standards

Intel NUC Board NUC5PGYH complies with the safety standards stated in Table 31 when correctly

installed in a compatible host system.

Table 31. Safety Standards

Standard

CSA/UL 60950-1

EN 60950-1

IEC 60950-1

Title

Information Technology Equipment – Safety - Part 1: General Requirements

(USA and Canada)

Information Technology Equipment – Safety - Part 1: General Requirements

(European Union)

Information Technology Equipment – Safety - Part 1: General Requirements

(International)

65

Intel NUC Board NUC5PGYH Technical Product Specification

5.1.2

European Union Declaration of Conformity Statement

We, Intel Corporation, declare under our sole responsibility that the product Intel NUC Board

NUC5PGYH is in conformity with all applicable essential requirements necessary for CE marking, following the provisions of the European Council Directive 2004/108/EC (EMC Directive),

2006/95/EC (Low Voltage Directive), and 2002/95/EC (ROHS Directive).

The product is properly CE marked demonstrating this conformity and is for distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC, 2006/95/EC, and

2002/95/EC.

Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC, 2006/95/EC a

2002/95/EC.

Dansk Dette produkt er i overensstemmelse med det europæiske direktiv 2004/108/EC,

2006/95/EC & 2002/95/EC.

Dutch Dit product is in navolging van de bepalingen van Europees Directief 2004/108/EC,

2006/95/EC & 2002/95/EC.

Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC, ja 2006/95/EC ja 2002/95/EC kehtestatud nõuetele.

Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC, 2006/95/EC & 2002/95/EC määräyksiä.

Français Ce produit est conforme aux exigences de la Directive Européenne 2004/108/EC,

2006/95/EC & 2002/95/EC.

Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie 2004/108/EC,

2006/95/EC & 2002/95/EC.

Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών 2004/108/EC,

2006/95/EC

και 2002/95/EC.

Magyar E termék megfelel a 2004/108/EC, 2006/95/EC és 2002/95/EC Európai Irányelv előírásainak.

Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer 2004/108/EC,

2006/95/EC, & 2002/95/EC.

Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC, 2006/95/EC &

2002/95/EC.

Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC, 2006/95/EC un 2002/95/EC noteikumiem.

Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC, 2006/95/EC, ir 2002/95/EC nuostatas.

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej 2004/108/EC,

2006/95/EC u 2002/95/EC.

Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet 2004/108/EC,

2006/95/EC & 2002/95/EC.

Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej 2004/108/EC,

206/95/EC i 2002/95/EC.

Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC, 2006/95/EC

& 2002/95/EC.

66

Regulatory Compliance and Battery Disposal Information

Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC, 2006/95/EC

& 2002/95/EC.

Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív 2004/108/EC,

2006/95/EC a 2002/95/EC.

Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC, 2006/95/EC in

2002/95/EC.

Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC, 2006/95/EC &

2002/95/EC.

Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC, 2006/95/EC ve 2002/95/EC yönergelerine uyar.

5.1.3

Product Ecology Statements

The following information is provided to address worldwide product ecology concerns and regulations.

5.1.3.1

Disposal Considerations

This product contains the following materials that may be regulated upon disposal: lead solder on the printed wiring board assembly.

5.1.4

EMC Regulations

Intel NUC Board NUC5PGYH complies with the EMC regulations stated in Table 32 when correctly

installed in a compatible host system.

Table 32. EMC Regulations

Regulation Title

FCC 47 CFR Part 15, Subpart B Title 47 of the Code of Federal Regulations, Part 15, Subpart B, Radio Frequency

Devices. (USA)

ICES-003

EN55022

Interference-Causing Equipment Standard, Digital Apparatus. (Canada)

Limits and methods of measurement of Radio Interference Characteristics of

Information Technology Equipment. (European Union)

EN55024

EN55022

Information Technology Equipment – Immunity Characteristics Limits and methods of measurement. (European Union)

Australian Communications Authority, Standard for Electromagnetic Compatibility.

(Australia and New Zealand)

CISPR 22

CISPR 24

VCCI V-3, V-4

KN-22, KN-24

CNS 13438

Limits and methods of measurement of Radio Disturbance Characteristics of

Information Technology Equipment. (International)

Information Technology Equipment – Immunity Characteristics – Limits and Methods of Measurement. (International)

Voluntary Control for Interference by Information Technology Equipment. (Japan)

Korean Communications Commission – Framework Act on Telecommunications and

Radio Waves Act (South Korea)

Bureau of Standards, Metrology, and Inspection (Taiwan)

67

Intel NUC Board NUC5PGYH Technical Product Specification

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par le ministére des Communications du Canada.

68

Regulatory Compliance and Battery Disposal Information

Japan VCCI Statement

Japan VCCI Statement translation: This is a Class B product based on the standard of the

Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Korea Class B Statement

Korea Class B Statement translation: This equipment is for home use, and has acquired electromagnetic conformity registration, so it can be used not only in residential areas, but also other areas.

69

Intel NUC Board NUC5PGYH Technical Product Specification

5.1.5

e-Standby and ErP Compliance

Intel NUC Board NUC5PGYH meets the following program requirements in an adequate system configuration, including appropriate selection of an efficient power supply:

• EPEAT*

• Korea e-Standby

• European Union Energy-related Products Directive 2013 (ErP) Lot 6

For information about

Electronic Product Environmental Assessment Tool (EPEAT)

Refer to

http://www.epeat.net/

Korea e-Standby Program

European Union Energy-related Products Directive 2009 (ErP) http://www.kemco.or.kr/new_eng/pg02/pg02100300

.asp

http://ec.europa.eu/enterprise/policies/sustainablebusiness/sustainable-productpolicy/ecodesign/index_en.htm

70

Regulatory Compliance and Battery Disposal Information

5.1.6

Regulatory Compliance Marks (Board Level)

Intel NUC Board NUC5PGYH has the regulatory compliance marks shown in Table 33.

Table 33. Regulatory Compliance Marks

Description

UL joint US/Canada Recognized Component mark. Includes adjacent UL file number for Intel NUC Boards: E210882.

FCC Declaration of Conformity logo mark for Class B equipment.

Mark

CE mark. Declaring compliance to the European Union (EU) EMC directive, Low Voltage directive, and RoHS directive.

For CE Mark-Related Questions:

Intel Corporation

Attn: Corporate Quality

2200 Mission College Blvd.

Santa Clara, CA 95054-1549

USA

Australian Communications Authority (ACA) and New Zealand Radio Spectrum

Management (NZ RSM) C-tick mark. Includes adjacent Intel supplier code number,

N-232.

Japan VCCI (Voluntary Control Council for Interference) mark.

Korea Certification mark. Includes an adjacent KCC (Korean Communications

Commission) certification number: KCC-REM-CPU-NUC5PGYH.

Taiwan BSMI (Bureau of Standards, Metrology and Inspections) mark. Includes adjacent Intel company number, D33025.

Printed wiring board manufacturer’s recognition mark. Consists of a unique UL recognized manufacturer’s logo, along with a flammability rating (solder side).

China RoHS/Environmentally Friendly Use Period Logo: This is an example of the symbol used on Intel NUC Boards and associated collateral. The color of the mark may vary depending upon the application. The Environmental Friendly Usage Period (EFUP) for Intel NUC Boards has been determined to be 10 years.

V-0

71

Intel NUC Board NUC5PGYH Technical Product Specification

5.2

Battery Disposal Information

CAUTION

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used batteries must be in accordance with local environmental regulations.

PRÉCAUTION

Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des piles usagées doit respecter les réglementations locales en vigueur en matière de protection de l'environnement.

FORHOLDSREGEL

Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i overensstemmelse med gældende miljølovgivning.

OBS!

Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier bør kastes i henhold til gjeldende miljølovgivning.

VIKTIGT!

Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras enligt de lokala miljövårdsbestämmelserna.

VARO

Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on mahdollista.

Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten mukaisesti.

VORSICHT

Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen Batterietyp ersetzt werden.

Entsorgen Sie verbrauchte Batterien den Anweisungen des Herstellers entsprechend.

AVVERTIMENTO

Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto. Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.

72

Regulatory Compliance and Battery Disposal Information

PRECAUCIÓN

Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del fabricante.

WAARSCHUWING

Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type batterij.

Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.

ATENÇÃO

Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto. As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias usadas deve ser feita de acordo com as regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ

Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу. Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.

UPOZORNÌNÍ

V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné, baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními předpisy o životním prostředí.

Προσοχή

Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία λανθασμένου

τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι δυνατό. Η απόρριψη των

χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με τους κατά τόπο περιβαλλοντικούς

κανονισμούς.

VIGYÁZAT

Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket lehetőség szerint

újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi előírásoknak megfelelően kell kiselejtezni.

73

Intel NUC Board NUC5PGYH Technical Product Specification

AWAS

Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi peraturan alam sekitar tempatan.

OSTRZEŻENIE

Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi przepisami ochrony środowiska.

PRECAUŢIE

Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător. Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să respecte reglementările locale privind protecţia mediului.

ВНИМАНИЕ

При использовании батареи несоответствующего типа существует риск ее взрыва.

Батареи должны быть утилизированы по возможности. Утилизация батарей должна проводится по правилам, соответствующим местным требованиям.

UPOZORNENIE

Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu.

Batérie by sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať v súlade s miestnymi predpismi na ochranu životného prostredia.

POZOR

Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.

Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi okoljevarstvenimi predpisi.

UYARI

Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri dönüştürülmelidir.

Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

O

СТОРОГА

Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.

Якщо можливо, використані батареї слід утилізувати. Утилізація використаних батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

74

Regulatory Compliance and Battery Disposal Information

75

Intel NUC Board NUC5PGYH Technical Product Specification

76

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents