Graco 313296J User's Manual

Add to My manuals
108 Pages

advertisement

Graco 313296J User's Manual | Manualzz
Instructions - Parts
Warm Melt Supply
Systems
313296J
For use with heated bulk supply of medium to high viscosity sealant and adhesive
materials. Not for use in hazardous locations. Intended for indoor use only.
D60 3 inch dual post
60 liter (16 gallon), 30 liter (8 gallon), and
20 liter (5 gallon) sizes
150 psi (1.0 MPa, 10 bar) Maximum Air Inlet Pressure
D200 3 inch dual post
200 liter (55 gallon)
150 psi (1.0 MPa, 10 bar) Maximum Air Inlet Pressure
D200S 6.5 inch dual post
200 liter (55 gallon)
125 psi (0.9 MPa, 9 bar) Maximum Air Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 4 for model information.
The Graco Control Architecture Electric Components
are listed in Intertek’s Directory of Listed Products.
D200s (WM2179) Shown
EN
Contents
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Heat Control Zone Selection . . . . . . . . . . . . . . . . . . . . . 7
Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . 8
Single Supply Systems . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tandem Supply Systems . . . . . . . . . . . . . . . . . . . . . . . 9
Integrated Air Controls . . . . . . . . . . . . . . . . . . . . . . . . 10
Air Line Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2-Button Interlock Air Controls . . . . . . . . . . . . . . . . . . 11
Communications Gateway Module . . . . . . . . . . . . . . . 11
Fluid Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . 12
User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . 17
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connect Power Source . . . . . . . . . . . . . . . . . . . . . . . . 18
Install/Adjust Drum Low or Empty Sensor . . . . . . . . . 19
Light Tower Accessory . . . . . . . . . . . . . . . . . . . . . . . . 19
Attach Drum Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Check Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hose Installation and Care . . . . . . . . . . . . . . . . . . . . . 23
Overview of Temperature Control Settings . . . . . . . . . 23
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Purge System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Set Values on Display Module . . . . . . . . . . . . . . . . . . 24
Load Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
System Heat Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Prime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . 28
Trigger Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start and Adjust Ram . . . . . . . . . . . . . . . . . . . . . . . . . 28
Start and Adjust Pump . . . . . . . . . . . . . . . . . . . . . . . . 28
Automatic Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Manual Crossover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Recirculate Function . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Depressurize Function . . . . . . . . . . . . . . . . . . . . . . . . 30
Change Drums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Replace Throat Seals . . . . . . . . . . . . . . . . . . . . . . . . . 32
Platen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Electrical Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Pump Heaters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Diagnose Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Clear Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2
Alarm Codes and Troubleshooting . . . . . . . . . . . . . . . 36
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Air Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Displacement Pump . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Disconnect Pump from Platen . . . . . . . . . . . . . . . . . . 50
Connect Pump to Platen . . . . . . . . . . . . . . . . . . . . . . . 51
Replace Pump Heaters . . . . . . . . . . . . . . . . . . . . . . . 51
Replace Platen Heaters and Sensor . . . . . . . . . . . . . 52
Replace Platen Wipers . . . . . . . . . . . . . . . . . . . . . . . . 54
Replace Ram Piston Rod Seals . . . . . . . . . . . . . . . . . 54
Electrical Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Display/User Interface . . . . . . . . . . . . . . . . . . . . . . . . 58
Replace Fluid Control Module . . . . . . . . . . . . . . . . . . 59
Replace Cable Track . . . . . . . . . . . . . . . . . . . . . . . . . 60
Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Ram A Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
D200 Single Ram Schematic . . . . . . . . . . . . . . . . . . . 61
D200 Ram A Schematic . . . . . . . . . . . . . . . . . . . . . . . 62
D200 Ram B Schematic . . . . . . . . . . . . . . . . . . . . . . . 63
D200 Displacement Pump and Platen Schematics . . 64
D200 Junction Box Schematic . . . . . . . . . . . . . . . . . . 65
D200 Cable Track Schematic . . . . . . . . . . . . . . . . . . . 66
D60 Single Ram Schematic . . . . . . . . . . . . . . . . . . . . 67
D60 Ram A Schematic . . . . . . . . . . . . . . . . . . . . . . . . 68
D60 Ram B Schematic . . . . . . . . . . . . . . . . . . . . . . . . 69
D60 Pump and Platen Schematic . . . . . . . . . . . . . . . . 70
D60 Junction Box Schematic . . . . . . . . . . . . . . . . . . . 71
D60 Cable Harness Schematic . . . . . . . . . . . . . . . . . 72
Electrical Enclosure Schematic . . . . . . . . . . . . . . . . . 73
Electrical Enclosure Schematic . . . . . . . . . . . . . . . . . 74
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Warm Melt Kits for D200 Systems . . . . . . . . . . . . . . . 78
Warm Melt Kits for D60 Systems . . . . . . . . . . . . . . . . 83
Electrical Enclosure Parts . . . . . . . . . . . . . . . . . . . . . . 90
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Appendix A - User Interface Display . . . . . . . . . . . . . . . 93
Display Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Display Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Setup Mode Screens . . . . . . . . . . . . . . . . . . . . . . . . . 95
Run Mode Screens . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
D200 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
D60 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . 108
Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
313296J
Related Manuals
Related Manuals
Manuals are available at www.graco.com.
Component Manuals in U.S. English:
Manual
Description
313528
313529
313526
313527
Tandem Supply Systems Operation
Tandem Supply Systems Repair-Parts
Supply Systems Operation
Supply Systems Repair-Parts
312375
Check-Mate® Displacement Pumps
Instructions-Parts
312376
312468
Check-Mate® Pump Packages
Instruction-Parts
200 cc Check-Mate Displacement Pump
Repair Parts
311238
NXT™ Air Motor Instructions-Parts
312374
Air Controls Instructions-Parts
3A0099
Two-Zone Enclosure Expansion Kit
Instructions-Parts
Two-Zone and Four-Zone Enclosure
Accessory Kits Instructions-Parts
3A0100
3A0135
Bracket Mounting Kits Parts
312491
Pump Fluid Purge Kit Instructions
312492
Drum Roller Kit Instructions
312493
Light Tower Kit Instructions
309160
Heated Hose Instructions-Parts
312396
Hotmelt/Warm Melt Heated Fluid Regulator Instructions-Parts
307517
Mastic Fluid Regulator Instructions-Parts
309133
Pressure Compensating Valve
Instructions-Parts
Heated Header and Manifold
Instructions-Parts
Hot Melt Dispense Guns
Instructions-Parts
309181
311209
310538
309376
312864
313138
406681
313296J
Therm-O-Flow® Automatic Dispense
Valves Instructions-Parts
EnDure™ Automatic Dispense Valves
Instructions-Parts
Communications Gateway Module
Instructions-Parts
Supply System Communications Gateway Module Installation Kit Instructions-Parts
Platen Cover Kit Instructions
3
Models
Models
Check the identification plate (ID) for the 6-digit part number of your warm melt
supply system. Use the following matrix to define the construction of your system,
based on the six digits. For example, Part No. WM2979 represents a Warm Melt
supply system (WM), a carbon steel Check-Mate 200 Severe Duty® displacement
pump with an NXT 3400 air motor (pump code 29), a 6.5 in. dual post ram with
integrated air controls (7) and a 55-gallon, uncoated platen with an EPDM seal
(9).
ID
NOTE: Some configurations in the following matrix cannot be built. See the
Product Selection guide for available systems.
To order replacement parts, see Parts section in this manual and in manual
313527. The digits in the matrix do not correspond to the Ref. Nos. in the Parts
drawings and lists.
WM
9
Fifth Digit
Sixth Digit
(See Table 1
for 2-digit
Pump Code)
TW
(Warm Melt
Tandem
Supply
System)
Platen and Seal Options
Size
Ram Options
DataTra
k
Style Voltage Air Controls
4
3 in.
D60
no volt
INT
F
5
3 in.
D200
no volt
H
6
3 in
D200i
no volt
INT
2-Button
Interlock
INT
2-Button
Interlock
2-Button
Interlock
R
Pump Code
WM
(Warm Melt
Single Supply
System)
7
29
First and
Third and
Second Digit Fourth Digit
7 6.5 in. D200s no volt
8 6.5 in. D200si no volt
Y
3 in.
D60i
no volt
Platen
Size
L
U
Y
8
9
Key:
D = Dual post ram
i = 2-Button interlock
s = 6.5 in. ram
INT = Integrated air controls
F = Flat
SW = Single wiper
DW = Dual wiper
DR = Dual o-ring
20 L
(5 Gal)
20 L
(5 Gal)
30 L
(8 Gal)
30 L
(8 Gal)
60 L
(16 Gal)
60 L
(16 Gal)
200 L
(55 Gal)
200 L
(55 Gal)
Platen
Style
Platen
Material
F, SW
SST
F, DW
CS
F, SW
SST
F, DW
CS
F, SW
SST
F, DW
DR
CS
PTFE
coated
AL
DR
AL
Seal
Material
PTFE
coated
Polyurethane
PTFE
coated
Polyurethane
PTFE
coated
Polyurethane
EPDM
EPDM
Table 1: Check-Mate Pump Identification Code/Part
Pump Pump Part No. (see Pump Pump Part No. (see
Code
manual 312376)
Code
manual 312376)
NXT 2200/CM 200
21
P23LCS
22
P23LCM
26
P23LSM
NXT 3400/CM 200
29
2A
2G
4
TI11157A
NXT 6500/CM 200
2L
P68LCS
2M
P68LCM
2U
P68LSM
P36LCS
P36LCM
P36LSM
313296J
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can cause
electric shock.
• Turn off and disconnect power at main switch before disconnecting any cables and before servicing
equipment.
• Connect only to grounded power source.
• All electrical wiring must be done by a qualified electrician and comply with all local codes and
regulations.
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes
are present.
• Ground all equipment in the work area.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns:
• Do not touch hot fluid or equipment.
• Wait until equipment/fluid has cooled completely.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the dispense outlet.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning,
checking, or servicing equipment.
313296J
5
Warnings
WARNING
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
SPLATTER HAZARD
Hot or toxic fluid can cause serious injury if splashed in the eyes or on skin. During blow off of platen,
splatter may occur.
• Use minimum air pressure when removing platen from drum.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or
swallowed.
• Read MSDS’s to know the specific hazards of the fluids you are using.
• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
• Always wear impervious gloves when spraying or cleaning equipment.
• If this equipment is used with isocyanate material, see additional information on isocyanates in Isocyanate Conditions Section of this manual.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment
and follow the Pressure Relief Procedure in this manual when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
6
313296J
Overview
Overview
System Description
Table 1: Electrical Requirements
Warm melt supply systems are used for melting and
pumping warm melt adhesives and high viscosity sealants.
The system consists of an air-powered ram that drives a
Check-Mate pump and a heated platen into a drum of
material. The heated platen heats the material and the
pump removes it from the drum. The material is then
pushed through a supply hose to the applicator.
All features of the warm melt supply system are controlled by Graco Control Architecture components: Fluid
Control Module (FCM), Temperature Control Modules
(TCM), and the display module. The FCM controls the
motor and pump, and the TCMs control the heaters. The
display module provides the user interface for the entire
warm melt supply system.
Power Requirements
A 30A (minimum) - 60A (maximum) circuit breaker (not
provided) must be installed on the incoming power supply. See Table 1, and Technical Data, page 106, for
more information regarding electrical requirements.
AC Panel
Voltage
HZ
Phase
Full Load
Amps
240
50/60
1
57.0
Heat Control Zone Selection
Warm melt supply systems have four heat zones (see
FIG. 1).
•
Zones 1 and 2 are always used for the heated
platen and the heated pump respectively.
•
Zones 3 and 4 are used for the heated hose and
valve. These zones are rated for 1920 watts at 240
volts.
Heated hoses have a 16-pin connector on the inlet end
cable, and an 8-pin connector on the outlet end cable.
All heated valves, manifolds, and heaters are equipped
with an 8-pin matching connector. Accessory cables are
available for other possible combinations.
Valve 1
Hose 1
ZONE 1
Control
Platen
ZONE 2
Control
ZONE 3
Control
ZONE 4
Control
1920 Watts max
1920 Watts max
Pump
FIG. 1: Heat Control Zone Selection
313296J
7
Component Identification
Component Identification
Single Supply Systems
AF
D200s Ram Shown
Lift Locations
S
NOTE: Do not
use air motor lift
ring (S) to lift
entire system.
V
AD
C
G
H
J
K
AE
A
U
X
D
Z
E
T
FIG. 2: Single Supply System
Key:
A
C
D
E
G
H
J
K
S
T
U
8
Ram Assembly
Air Motor
Heated Check-Mate Displacement Pump
Heated Platen
Display Module
Electrical Enclosure
Integrated Air Controls (see FIG. 4)
Fluid Control Module (inside shroud)
Lift Ring (air motor)
Platen Bleed Port
Pump Outlet
V
X
Z
AD
AE
AF
Platen Lift Rod
Wet Cup
Main Air Line (not supplied)
Air Motor Solenoid
Junction Box
Cable Track
313296J
Component Identification
Tandem Supply Systems
D200s Rams Shown
Supply System A
AF
H
S
A
G
Supply System B
F
B
AD
N
V
J
C
K
AE
To heated
manifold
(243697)
X
Z
U
D
r_wm2179_313269_4a
E
FIG. 3: Tandem Supply System
Key:
A
B
C
D
E
F
G
H
J
K
N
S
T
U
V
Ram A
Ram B
Air Motor
Heated Check-Mate Displacement Pump (Ram A and B)
Heated Platen (Ram A and B)
Drum Empty Sensor (partially hidden; Ram A and B)
Display Module (Ram A only)
Electrical Enclosure (Ram A and B)
Integrated Air Controls (Ram A and B); see page 10
Fluid Control Module (inside shroud, Ram A and B)
CAN Communication Cable
Lift Ring (Air Motor)
Platen Bleed Port
Pump Outlet
Platen Lift Rod
313296J
X
Z
AD
AE
AF
Wet Cup
Main Air Line (not supplied)
Air Motor Solenoid (Ram A and B)
Junction Box (Ram A and B)
Cable Track (Ram A and B)
9
Component Identification
NOTE:
See FIG. 2 and FIG. 3. Before you install the system,
you should be familiar with the following components.
Integrated Air Controls
D60, D200, and D200s Models
The integrated air controls include:
Reference numbers and letters in parentheses in the
text refer to the callouts in the figures.
•
Both rams (A and B) include a Check-Mate Pump (D),
platen (E), integrated air controls (J), drum empty sensor (F), and fluid control module (K).
Main air slider valve (BA): turns air on and off to
the system. When closed, the valve relieves pressure downstream.
•
Ram air regulator (BB): controls ram up and down
pressure and blowoff pressure.
•
Ram director valve (BC): controls ram direction.
•
Exhaust port with muffler (BD)
•
Air motor regulator (BE): Controls air pressure to
motor.
•
Air motor slider valve (BF): turns air on and off to
the air motor. When closed, the valve relieves air
trapped between it and the air motor. Push the valve
in to shutoff. The air solenoid (AD), the air motor
valve (BF), and the main air slider valve (BA) must
be open for air to flow.
•
Blowoff button (BG): turns air on and off to push
the platen out of an empty drum.
Only Ram A includes the display module (G).
•
Drum empty sensor (F). Signals drum empty condition. See FIG. 11, page 19.
•
Display module (G). Mounted on Ram A only. Provides Run Mode status screens, Setup screens, and
control keys. See FIG. 8, page 13.
•
Fluid control module (K). See FIG. 7, page 12.
•
Integrated air controls (J). See FIG. 4.
•
Air motor solenoid (AD). Solenoid is on when the
selected ram is on and in Run Mode, Recirculate
Mode, or Prime Mode. Solenoid is off when system
is shut off or when in Depressurize Mode, or the ram
is in an Inactive Ready Mode. The solenoid LED will
illuminate when the solenoid is on.
BF
•
Depressurize/recirculate fluid valve. Depressurizes
system when Depressurize Mode is active. Recirculates fluid when Recirculate Mode is active.
BE
BD
To depressurize the system, press the Depressurize
key
BC
on the display module and select
when asked if you want to depressurize the system.
Follow the Pressure Relief Procedure on page 28.
Shutting off power or removing power from the system will not depressurize the system.
BG
BA
BB
ti10438a
FIG. 4. Integrated Air Controls
10
313296J
Component Identification
Air Line Accessories
See Supply Systems Operation manual.
•
Air line drain valve. Not included.
•
Air line filter: removes harmful dirt and moisture
from compressed air supply. Not included.
•
Second bleed-type air valve isolates air line
accessories and supply system for servicing. Locate
upstream from all other air line accessories. Not
included.
•
Air relief valve: automatically relieves excessive
pressure. Not included.
2-Button Interlock Air Controls
D60i, D200i, and D200si Models
Communications Gateway
Module
The Communications Gateway Module (CGM) provides
a control link between Graco Control Architecture based
systems and a selected fieldbus. This provides the
means for remote monitoring and control by external
automation systems.
Data provided by the CGM to the fieldbus depends on
which Graco Control Architecture based system and
fieldbus are connected. A data map supplied on a map
token is defined for this pairing. Once the data map has
been loaded into the CGM, it is stored internally, and the
map token is no longer required for operation.
See the Supply System Communications Gateway Module Installation Kit manual for fieldbus parameter setup
instructions and screen descriptions.
CGM Module Status LED Signals
Systems that have 2-Button Interlock controls have the
following additional components:
•
•
Signal
2-Button Module: See the Air Controls manual for
information.
Roller switch (CA): shuts off air supply when it
contacts the bracket actuator. Operator must push
and hold the activation buttons simultaneously to
resume ram movement.
Description
Green on
System is powered up
Yellow
Internal communication in progress
Red
Solid
CGM hardware failure
*Red
(7 flashes)
Data map load failure
Incorrect data map for fieldbus type
No data map loaded
*
Activation
Buttons
ti10843a1
FIG. 5: 2-Button Module
•
The red LED will flash a code, pause, then repeat.
See Communications Gateway Module manual
312864 for diagnostic information. Verify that you are
using the correct token for your system and reinstall
token. If fails, order new token.
Bracket actuator (CB): attaches to the platen lift
rod. When platen is outside of drum, actuator makes
contact with the roller switch.
CA
CB
ti10846a
FIG. 6: Roller Switch and Bracket Actuator
313296J
11
Component Identification
Fluid Control Module
Table 2: FCM Sensor Connections
Connection
Ram
Sensor Description
1
Ram A and Ram B
Air motor solenoid (wire labeled 3), drum low (wire labeled 1),
drum empty (wire labeled 2)
2
Ram A
Light tower
3
Ram A + B
Fluid depressurize/recirculate solenoid
4
not used
not used
5
Ram A and Ram B
Air motor reed switch, sensors
6
not used
not used
7
Ram A
Filter pressure at inlet and outlet
CAN communication
cable 1
Ram A
From Ram A FCM to display module.
CAN communication
cable 2
Ram A and Ram B
15 ft (4.57 m) from Ram A FCM to Ram B FCM.
3
7
4
CAN Cable 2
6
TI12337A
5
TI12336A
CAN Cable 1
FIG. 7: FCM Sensor Connections
12
313296J
Component Identification
User Interface
FIG. 8: Display Module
Table 3: Display Module Button Functions
Button
On/Off
Function
Powers air motor solenoid ON and OFF from Ram Operation screen (FIG. 71, page 100).
•
When ON, the air motor solenoid is ON and the pump of the active ram is pressurized.
•
When OFF, the air motor solenoids are OFF.
CAUTION: Turning the air motor solenoid OFF relieves pressure from the pump motor. It does
not depressurize the fluid pressure. Follow the Pressure Relief Procedure, page 28.
NOTE: The ram up/down and blowoff air is independent of the electronic controls and can be
operated anytime the main air slider valve is open and air pressure is available.
Powers heat ON and OFF from Heat Run screen (FIG. 72, page 101).
•
When ON, the enabled heat zones are ON.
•
When OFF, all heat zones are OFF.
Cancel
Cancel a selection or number entry while in the process of entering a number or making a
selection.
Setup
Toggle between run and setup screens.
Enter
•
Setup changes can be made while system is operating.
•
If setup screens are password protected, button toggles between run and password entry
screen.
Opens drop down menus on Setup fields.
Press to enter changes and make a selection.
Arrows Left/Right Navigate left or right to a new screen.
Navigate left or right within a screen while in Jump In mode. See Appendix A - User Interface
Display, page 93, for more information.
Arrows Up/Down Navigate up or down within a screen or to a new screen.
• Move between selections within a drop-down menu.
•
313296J
Increment or decrement the selected numerical field within a selection menu.
13
Component Identification
Table 3: Display Module Button Functions
Button
Soft Key
Function
Soft keys activate the mode or action represented by the icon above each button in the LCD.
See Table 4 for soft key modes and actions.
Table 4: Display Soft Key Icons
Icon
Function
Depressurize
Depressurize relieves fluid pressure from the pump outlet to below the platen on the currently
active ram.
If system is pressurized, press button.
•
When prompted to depressurize the system, select
. Depressurizing the
or
active ram will depressurize both rams.
NOTE: If additional user-supplied check valves have been added to the system, only the
active ram will be depressurized. You must perform manual crossover and select depressurize
again to depressurize both rams. See Crossover section of this table on page 15.
If system is depressurized, press button.
•
Pump Prime
When prompted to pressurize the system, select
or
.
Pump Prime
• Tandem ram: if pump is off, activates the air solenoid on the active ram;
• Tandem ram: if pump is on, activates the air solenoid on the inactive ram which enables you
to purge air and prime the pump;
• Single ram: activates air solenoid whether or not pump is on;
• clears the Pump Not Primed deviation or alarm (depending on setup selection); and
• resets the drum volume remaining to the drum fill volume setpoint for pump being primed.
Press button.
•
When prompted to prime the ram, select
to prime.
Press button to exit Prime Mode or to reset counter to the prime time.
•
Recirculate
When prompted to exit Prime Mode, select
to exit or
to reset prime counter.
Recirculate Mode pumps fluid from the drum, through the pump, and back into the drum on the
currently active ram.
Set motor air regulator to 30 psi (0.2 MPa, 2.1 bar) before pressing Recirculate key.
If system is not in Recirculate Mode, press button.
•
When prompted to turn recirculation on, select
or
. Adjust motor air regulator to
or
.
obtain desired flow rate.
If system is in Recirculate Mode, press button.
•
14
When prompted to turn recirculation off, select
313296J
Component Identification
Table 4: Display Soft Key Icons
Icon
Function
Crossover
Crossover key transitions the active ram to inactive, and inactive ram to active. Available on
Warm Melt Tandem Supply Systems only.
NOTE: If an alarm is present on the inactive ram, crossover will not be successful. Manual
crossover is disabled in single ram operation.
Press button.
•
Setback
Jump In
When prompted to initiate a crossover, select
or
.
Setback transitions the heaters into setback mode. The setpoint for each zone will be
decreased by the setback amount. See Heater System Setup Screen, page 95, and Heat
Run Screen, page 101.
In screens that have editable fields, press
to access the fields and make changes. See
Appendix A - User Interface Display, page 93, for more information.
NOTICE
To prevent damage to soft key buttons, do not
press the buttons with sharp objects such as pens,
plastic cards, or fingernails.
313296J
15
Component Identification
User Interface Display
NOTE: For details regarding the user interface display see Appendix A - User Interface Display, page
93.
Display Screen Components
The following figure calls out the navigational, status, and general informational components of each display screen.
Current Date and Time
Navigation
Status
Mode
Function Display
Displays soft keys
that are active for
particular screen
Soft Keys
FIG. 9: Display Screen Components
16
313296J
Installation
Installation
Accessories are available from Graco. Make certain all
accessories are adequately sized and pressure-rated to
meet the system’s requirements.
Component Identification illustrations are only a guide
for selecting and installing system components and
accessories. Contact your Graco distributor for assistance in designing a system to suit your particular
needs.
Location Requirements
•
Refer to Dimensions, page 104, for ram mounting
and clearance dimensions.
•
Install indoors only, and not near water or any other
liquid that is sprayed.
Location
NOTICE
Always lift supply system at proper lift locations (see
FIG. 2) to avoid equipment damage. Do not lift in any
other way.
Grounding
Ground the supply system as instructed here and in the
individual component manuals.
The power source conduit is not an adequate ground
for the system. The unit must be bonded to either the
building ground or a true earth ground. To reduce the
risk of static sparking, ground the pump, the object
being dispensed to, and all other dispensing equipment used or located in the dispensing area. All electrical wiring must be done by a qualified electrician
and comply with local codes and regulations.
Pump: use a ground wire and clamp. Loosen grounding
lug locknut and washer. Insert one end of supplied
ground wire into slot in lug and tighten locknut securely.
Connect other end of wire to a true earth ground. See
FIG. 10.
1. Attach a lifting sling at the proper lift spots. Lift off
the pallet using a crane or a forklift. See FIG. 2 for
proper lift locations.
ti8250a
2. Position the ram so the air controls and electrical
enclosure are easily accessible. Ensure that there is
enough space overhead for the ram to raise fully.
3. Using the holes in the ram base as a guide, drill
holes for 1/2 in. (13 mm) anchors.
4. Ensure that the ram base is level in all directions. If
necessary, level the base using metal shims.
Secure the base to the floor using 1/2 in. (13 mm)
anchors that are long enough to prevent the ram
from tipping.
313296J
FIG. 10: Ground Pump
Air and fluid hoses: use only electrically conductive
hoses.
Air compressor: follow manufacturer’s recommendations.
Dispense valve: ground through connection to a properly grounded fluid hose and pump.
17
Installation
Fluid supply container: follow local code.
NOTE: See Power Requirements, page 7, for circuit
protection requirements.
Object being sprayed: follow local code.
Solvent pails used when flushing: follow local code.
Use only conductive metal pails, placed on a grounded
surface. Do not place the pail on a nonconductive surface, such as paper or cardboard, which interrupts
grounding continuity.
To maintain grounding continuity when flushing or
relieving pressure: hold metal part of the dispense
valve firmly to the side of a grounded metal pail, then
trigger the valve.
Connect Power Source
The electrical enclosure comes already attached and
wired to the ram; however, before the supply system
becomes functional you must connect the electrical
enclosure to a power source.
1. Open electrical enclosure door and locate power
line filter.
2. Have a qualified electrician perform the following
steps:
a. Connect your plant power to the electrical
enclosure power line filter according to local
codes. A 1-3/8 in. (35 mm) diameter opening is
provided on the side of the enclosure adjacent
to the label. This opening is suitable for a 1 in.
npt conduit or strain relief fitting (supplied).
b. Connect a power protective ground to the center post on the line end of the power line filter.
NOTE: Install safety insulation boots (supplied) on
the power line. Install 1/4 in. ring lugs (user supplied) on the power line and power protective
ground line prior to connecting to the power line filter posts.
Have a qualified electrician connect power according
to national, state, and local safety and fire codes.
NOTE: Required voltage and amperage is noted on
the electrical enclosure label. Also see Table 1.
Before running power to the unit, make sure the
plant electrical service meets the supply system’s
electrical requirements.
18
313296J
Installation
Install/Adjust Drum Low or
Empty Sensor
4. Attach the sensor to the corresponding connector
on the splitter cable. For drum low, attach the sensor to connector 1. For drum empty, attach the sensor to connector 2.
1. Position ram at desired level (low or empty).
NOTE: Follow Steps 2 through 4 only if installing the
low sensor.
2. Attach the low sensor to the existing sensor bracket
(EA), above the existing empty sensor (EE).
D200 Shown
5. Power system on.
6. Make precise adjustments by moving the sensor
within the slot on the sensor bracket. Use the yellow
indicator on the sensor cable to indicate a drum low
or empty condition.
Light Tower Accessory
Order the 255468 Light Tower Accessory as a diagnostic indicator for supply systems. See TABLE 5 for a
description of light tower signals.
EA
Table 5: Light Tower Signals
EE
ED
EB
Signal
Description
Yellow flashing
A low priority error exists.
Yellow on
A medium priority error exists.
Red flashing
A high priority error exists.
Red on
The system is shut down due to
error conditions.
FIG. 11: Low or Empty Sensor Kit
3. Replace the existing cable between the empty sensor (EE) and FCM connector (see FIG. 7, page 12)
with the empty/low sensor splitter cable.
313296J
19
Installation
Attach Drum Stops
Supply systems are shipped with drum stops in place to
help position the drum on the ram. For replacement
parts, order Kit 255477. The kit includes two each of
capscrews (FA), lock washers (not shown), and drum
stops (FB).
1. Locate the correct set of mounting holes on the ram
base.
2. Using the capscrews (FA) and lock washers (not
shown), attach the drum stops (FB) to the ram base.
D200 Shown
FB
FA
FIG. 12: Attach Drum Stops
55 gal (200 L)
30 gal (115 L)
8 gal (30 L)
5 gal (20 L)
FIG. 13: Drum Stop Location
20
313296J
Installation
Check Resistance
Check the Resistance Between the Supply
System and the True Earth Ground
The resistance between the supply system components and true earth ground must be less than 0.25
ohms.
Have a qualified electrician check the resistance
between each supply system component and the true
earth ground. The resistance must be less than 0.25
ohms. If the resistance is greater than 0.25 ohms a different ground site may be required. Do not operate the
system until the problem is corrected.
NOTE: Use a meter that is capable of measuring
resistance at this level.
Sensor Resistance Checks
Conduct these electrical checks with the main disconnect OFF.
NOTE: For dispense valve and hose sensor resistance checks, refer to your dispense valve manual
or hose manual.
The supply system includes a heat sensor and controller
for each of the four heated zones. To check sensor
resistance:
1. Make sure the power is off and that the disconnect
switch is in the OFF position.
2. Make electrical resistance checks for the components.
3. Replace any parts that have resistance readings
that do not comply with the ranges listed in Table 6.
NOTE: Check resistance at ambient room temperature (63°– 77°F [17°– 25°C]).
Table 6: RTD Sensor Resistance
Zone Component
Connector Pin
Range (ohms)
1
Platen
Pin 1 to 3
1050-1100 Ω
2
Fluid Pump
Pin 1 to 3
1050-1100 Ω
FIG. 14: RTD Connector Pins
313296J
21
Installation
Heater Resistance Checks
NOTE: Check resistance at ambient room temperature (63°– 77°F [17°– 25°C]).
Table 7: Resistance Chart of All Heaters
Conduct these electrical checks with the main power
disconnect OFF.
NOTE: For dispense valve and hose sensor resistance checks, refer to your dispense valve manual
or hose manual.
Zone
Component
Between
Unit
Terminals Voltage
Range
(ohms)
1
2
3
Platen - D200
Platen - D60
Pump
1 and 3
1 and 3
L and N
15 +5/-5
80 +10/-10
37 +5/-5
240
240
240
To check heater resistance:
1
1. Make sure the power is off and that the disconnect
switch is in the OFF position.
2. Make electrical resistance checks for the components. Refer to Table 7. Heater terminal pins are
located on the back of the enclosure (H). See FIG. 2,
page 8.
3
3. Replace any parts whose resistance readings do
not comply with the ranges listed in Table 7.
L
N
FIG. 15: Heater Terminal Pins
22
313296J
Installation
Hose Installation and Care
Mechanical Setup
1. Fill displacement pump wet cup 2/3 full with Graco
Throat Seal Liquid (TSL).
NOTE: The warm melt supply system requires
Graco single-circuit material hoses rated at a maximum of 1920 Watts.
2. Turn all air regulators to their full counterclockwise
position.
1. Connect heated hose to the pump outlet.
3. Connect a 3/4 in. (19 mm) air line from an air source
to the system air inlet. Refer to the pump performance curves in the Check-Mate Pump Packages
manual to determine your air supply flow requirements.
2. Use two wrenches to tighten. Torque to 470-550
in-lbs (53.1-62.1 N•m).
NOTE: Quick disconnects restrict flow for large air
motors.
Hose Installation
Overview of Temperature
Control Settings
3. Wrap exposed fittings on the pump outlet with
Nomex insulation and secure insulation using fiberglass tape.
Temperature controls are set in Setup mode. See Setup
Mode Screens on page 95 for information about setting
temperature controls.
See Run Mode Screens on page 100 for information on
controlling temperatures for each zone.
4. Connect hose adapter to green receptacle on junction box.
FIG. 16: Connect Hose to Junction Box
5. Securely tighten the 16-pin electrical connectors on
long heated hose leads into 16-socket receptacles
on the end of the hose adapter.
6. Securely tighten the 8-socket electrical connectors
on short heated hose leads into 8-pin receptacle
located on the dispense valves.
Hose Care Guidelines
Refer to the Hotmelt/Warm Melt Heated Hose manual
for details regarding hose care guidelines.
313296J
23
Setup
Setup
The pump was tested with lightweight oil, which is left in
the fluid passages to protect parts. To avoid contaminating fluid with oil, flush the pump with a compatible solvent before use. See Purge System, step 2.
Purge System
Purging the system before the initial use can prevent
material contamination, which may cause the material to
fail or perform poorly.
NOTICE
Purge the system before performing the initial material
loading procedure. The system was factory-tested
using a light soluble oil, a soybean oil, or some other oil
as tagged. Flush the system to avoid contaminating the
material that has been designated for initial material
loading.
To purge the system perform the following procedure:
1. Select the material for the initial material load.
2. Verify whether the factory-test oil and the initial
material load are compatible:
a. If the two substances are compatible, omit the
remaining steps in this procedure and refer to
the start up and operation instructions.
b. If the two substances are incompatible, perform
the remaining steps in this procedure to flush
This equipment should not be used with more than
one type of fluid due to potential compatibility issues
that could result in an unpredictable reaction. Graco
recommends using new hoses when chemicals are
changed or care must be taken to assure that all
traces of one chemical are removed before introducing a second chemical.
3. Select a container of material that can eliminate the
factory-test oil from the system. If necessary, check
with Graco or the material supplier for a recommended solvent.
4. Before purging ensure the entire system and waste
container are properly grounded.
NOTE: Remove any dispense valve orifices before
purging. Reinstall after purging has been completed.
5. Purge the material through the system for approximately 1 to 2 minutes.
6. Remove the container if purge material was used.
Set Values on Display Module
Set desired values on display module Setup menus.
See Setup Mode Screens, page 95.
the system at ambient temperature.
Use fluids that are chemically compatible with the
equipment wetted parts. See the Technical Data sections in the equipment manuals.
24
313296J
Setup
Load Material
D200 Shown
J
Moving parts can pinch or amputate fingers. When
the pump is operating and when raising or lowering
the ram, keep fingers and hands away from the
pump intake, platen, and lip of the drum.
NOTICE
Do not use a drum of material that has been dented or
otherwise damaged; damage to the platen wiper can
result.
NOTE: Before loading material, ensure that there is
a minimum overhead clearance of 105 in. (267 cm)
and all air regulators are backed off to their full
counterclockwise position.
NOTE: Follow steps below for both rams if using a
tandem warm melt supply system.
1. Refer to FIG. 2, FIG. 3, and FIG. 4. Close all air regulators and air valves.
D
FIG. 17: Heated Platen
8. Set the director valve (BC) to DOWN and lower the
ram until fluid appears at the top of the platen bleed
port (J). Adjust ram air regulator (BB) as needed.
Set the director valve (BC) to neutral and close the
platen bleed port (J). 2-Button Interlock: If system
has this feature, press and hold both buttons to start
lowering the ram. See FIG. 5, page 11.
2. Open main air slider valve (BA) and set ram air regulator (BB) to 40 psi (0.28 MPa, 2.8 bar). Set director valve handle (BC) to UP and let the ram rise to
its full height. 2-Button Interlock: If the system has
this feature, ram will stop as it nears the top. Press
and hold both buttons to raise ram completely. See
FIG. 5 on page 11.
3. Lubricate the platen seals (D) with grease or other
lubricant compatible with the fluid you will pump.
4. Remove the drum cover and smooth the surface of
the fluid with a straightedge.
5. Put a full drum of fluid on the ram base, slide it back
against the drum stops, and center it under the
platen (D). An optional drum roller kit is available to
make it easier to load the drum on the base. Order
Kit 255627.
6. Remove bleed stick from platen bleed port (J). See
FIG. 17.
7. If drum has a plastic liner, pull it over edge of drum.
Secure liner with tape wrapped around circumference of drum.
313296J
25
Setup
System Heat Up
Never pressurize warm melt supply system while
using warm melt materials before turning on heat.
Many warm melt materials tend to expand when heating and may cause a heated hose to burst. Avoid the
potential of bursting a hose by opening the dispense
valve during system heat up and lock the dispense
valve trigger open every time you shut the system
down.
NOTE: Operate at the lowest temperature and pressure necessary for your application.
1. Turn the main disconnect on the electrical control
panel door to the ON position.
2. Press
while in the Heat Run screen to turn the
heaters on for enabled heat zones.
FIG. 18: Heat Run Screen - Ram A
26
313296J
Setup
Prime
1. Make sure the system is at required temperature.
2. Tandem Systems Only: To prime the active ram,
ensure that the system is not in Run Mode. To prime
the inactive ram, ensure that the system is on and in
Run Mode.
3. Single Systems Only: To prime the ram, ensure
that the system is on. The system may or may not
be in Run Mode.
(Prime active ram - not Run Mode)
FIG. 21: Prime Confirmation
6. When the timer expires the air motor solenoid LED
will turn off.
7. Prime the system until a smooth flow of material dispenses from the dispense valve.
8. Lock the dispense valve trigger lock.
NOTE: To exit Prime Mode before the timer expires,
press the Pump Prime key
. The display
prompts the operator to confirm. See FIG. 22. Select
to exit prime.
FIG. 19: Ram Operation Screen - Tandem System
(Prime inactive ram - in Run Mode)
FIG. 22: Exit Prime Mode Confirmation
NOTE: To extend the prime time counter, select
in FIG. 22. Display prompts operator to confirm.
FIG. 20: Ram Operation Screen - Tandem System
See FIG. 23. Select
to reset.
4. If using a manual dispense valve, unlock the dispense valve trigger and place dispense valve over a
waste container.
5. Press the Pump Prime key
. The display
prompts the operator to confirm. See FIG. 21. Select
to begin prime.
FIG. 23: Reset Prime Time Counter Confirmation
313296J
27
Operation
Operation
Pressure Relief Procedure
This procedure describes how to relieve pressure for the
supply system. Use this procedure whenever you shut
off the system and before checking or adjusting any part
of the system.
1. Lock the dispense valve trigger.
2. Press On/Off key
If you suspect that the dispense tip/nozzle or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the tip guard retaining nut or hose end coupling
and relieve pressure gradually, then loosen completely.
Now clear the tip/nozzle or hose.
Trigger Lock
Always engage the trigger lock when you stop dispensing to prevent the gun from being triggered accidentally
by hand or if dropped or bumped.
. If system is On, display will
Start and Adjust Ram
highlight
. Select
to turn off.
Moving parts can pinch or amputate fingers. When
the pump is operating and when raising or lowering
the ram, keep fingers and hands away from the
pump intake, platen, and lip of the drum.
To start and adjust the ram(s), follow the Load Material
procedure on page 25.
FIG. 24: System Function Screen
3. See FIG. 4, page 10. Close the air motor slider valve
(BF) and the main air slider valve (BA) on ram(s).
4. Set the ram director valve to DOWN. The ram will
slowly drop.
5. Jog the director valve up and down to bleed air from
ram cylinders.
6. Unlock the dispense valve trigger.
7. Hold a metal part of the dispense valve firmly to the
side of a grounded metal pail, and trigger the dispense valve to relieve pressure.
Start and Adjust Pump
NOTE: Follow steps below for both pumps if using a
tandem warm melt supply system.
1. Connect pump outlet fittings and hose (not supplied).
NOTE: Be sure all components are adequately sized
and pressure rated to meet the system’s requirements.
2. Be sure the pump air valve is closed. Then set the
ram air regulator (BB) to 50 psi (0.35 MPa, 3.5 bar).
Set the director valve (BC) to DOWN. See FIG. 4,
page 10.
8. Lock the dispense valve trigger.
9. Open all fluid drain valves on ram(s). Have a container ready to catch the drainage. Leave fluid drain
valves open until ready to dispense again.
28
313296J
Operation
3. Press
while in the Ram Operation screen.
Manual Crossover
(Tandem Warm Melt Supply System Only)
Manual crossover can only be initiated if the following
conditions are met:
FIG. 25: Ram Operation Screen - Tandem System
4. When the confirmation screen appears with a
prompt, select
to start the pump.
•
inactive ram is not in the drum empty error condition.
•
pump runaway and not primed alarms do not exist.
To initiate a manual crossover to the inactive ram:
1. From the Ram Operation screen, press the Crossover key
. The display prompts the operator
to confirm.
5. Open the pump air valve (BF) and keep the director
valve (BC) set to DOWN while pump is operating.
NOTE: Increase air pressure to the ram if the pump
does not prime properly with heavier fluids.
Decrease air pressure if fluid is forced out around
the top seal or platen.
2. Select
or select
to confirm manual crossover operation
to cancel.
Automatic Crossover
(Tandem Supply System Only)
Keep clear of the inactive ram, as automatic crossover may occur unexpectedly. To repair or adjust the
ram, first follow all steps of the Pressure Relief Procedure on page 28.
The automatic crossover feature allows continuous flow
and prevents system shutdown. If the active ram
encounters a pump runaway or drum empty alarm, it will
attempt an automatic crossover to the inactive ram.
FIG. 26: Crossover Function Screen
NOTE: If the active ram has a pump runaway error
or drum empty error, the system will attempt an
automatic crossover.
The system will generate a crossover error if the active
ram attempts an automatic crossover while the inactive
ram has a pump runaway, drum empty, or not primed
alarm. If this occurs, correct the error and clear the
alarm from the Alarm screen. See Alarm Screen, page
103, for details.
313296J
29
Operation
Recirculate Function
Depressurize Function
Recirculate mode pumps fluid from the drum, through
the pump, and back into the drum on the currently active
ram.
Follow the Pressure Relief Procedure on page 28.
Shutting off power or removing power from the system will not depressurize the system.
To enter Recirculate mode:
1. Set the motor air regulator to 30 psi (0.2 MPa, 2.1
bar).
2. From the Ram Operation screen, press the Recirculate key
. The display prompts the operator to
When the system is pressurized the depressurize function relieves fluid pressure from the pump outlet to
below the platen on the currently active ram. However,
when the system is depressurized pressing the depressurize key will restore fluid pressure.
confirm.
Depressurize System
3. Select
to confirm recirculation or select
to
cancel.
From the Ram Operation screen, press the Depressurize key
firm. Select
. The display prompts the operator to conto confirm depressurize or select
to cancel.
FIG. 27: Enter Recirculate Mode
4. Adjust motor air regulator to obtain desired flow
rate.
NOTE:
While in Recirculate Mode, the manual crossover
function cannot be used and the inactive ram cannot be primed.
FIG. 28: Depressurize Function Screen
To exit Recirculate Mode, press the Recirculate key
. The display prompts the operator to confirm.
Select
to confirm or select
to cancel. See FIG.
27.
NOTE:
You must exit Recirculate Mode before depressurizing or initiating a crossover.
30
313296J
Operation
NOTE:
Depressurizing the active ram will depressurize
both rams. However, if additional user-supplied
check valves have been added to the system, only
the active ram will be depressurized.
To depressurize both rams perform manual crossover (see Manual Crossover, page 29), and then
press the Depressurize key
again.
Pressurize System
From the Ram Operation screen, press the Depressurize key
firm. Select
. The display prompts the operator to conto confirm pressurize or select
to
drum. Use minimum amount of air pressure necessary to push the platen out of the drum.
Excessive air pressure in the material drum could
cause the drum to rupture, causing serious injury.
The platen must be free to move out of the drum.
Never use drum blowoff air with a damaged drum.
3. Once the platen clears the drum, release the
blow-off air button (BG) and allow the ram to rise to
its full height. 2-Button Interlock: If system has this
feature, the ram will stop as it nears the top. Press
and hold both buttons to raise ram completely. See
FIG. 5.
4. Remove empty drum.
cancel. See FIG. 28.
5. Inspect platen and, if necessary, remove any
remaining material or material build–up.
Change Drums
6. Place full drum on ram base.
7. Lower the ram and adjust the position of the drum
relative to the platen. See Load Material on page
25.
NOTE: Follow this procedure to change the drum on
a fully heated warm melt supply system.
NOTE: Follow this procedure for either ram if using
a tandem warm melt supply system.
NOTICE
Do not use a drum of material that has been
dented or otherwise damaged; damage to the
platen wiper can result.
1. Push in the air motor slider valve (BF) to stop the
pump. See FIG. 4.
2. Set ram director valve (BC) to UP to raise the platen
(D) and immediately press and hold the blowoff air
button (BG) until the platen (D) is completely out of
313296J
31
Maintenance
Maintenance
Shutdown
Follow the procedure below for normal system shut
down, such as at the end of the work day.
NOTICE
Turning the system OFF relieves pressure from the
pump motor; however, it does not depressurize the fluid
pressure. Follow the Pressure Relief Procedure, page
28.
NOTE: The ram up/down and blowoff air is independent of the electronic controls and can be operated
anytime the main air slider valve is open and air
pressure is available.
To reduce the risk of serious injury whenever you are
instructed to relieve pressure, always follow the Pressure Relief procedure.
Replace Throat Seals
Quick Coupler
Remove wet cup from displacement pump while
attached to the ram to replace throat seals.
1. Ensure displacement pump is at bottom of stroke.
1. Press
while in the Ram Operation screen to
turn off the air motor. Select
2. Press
to confirm.
2. Follow the Pressure Relief Procedure on page 28.
3. Remove Quick Coupler:
Remove clip (GC), and slide coupling cover (GB) up
to remove coupling (GA).
while in the Heater Run screen to turn
off the heaters. Select
to confirm.
GB
3. Follow the Pressure Relief Procedure, page 28.
Many warm melt materials tend to expand when heating and may cause a heated hose to burst. Avoid the
potential of bursting a hose by opening the dispense
valve during system heat up and lock the dispense
valve trigger open every time you shut the system
down.
GC
GA
ti10508a
FIG. 29: Remove Quick Coupler
4. Lift air motor rod to bring rod to top of stroke.
5. Remove wet cup and packing cartridge according to
instructions in displacement pump manual(s).
32
313296J
Maintenance
Platen Maintenance
Remove and Reinstall Platen Wipers
Refer to Supply Units Repair-Parts manual for instructions.
70
If the platen does not come out of the pail easily when
the pump is being raised, the air assist tube or check
valve may be plugged. A plugged valve prevents air
from reaching the underside of the plate to assist in raising it from the pail.
49
1. Turn off main disconnect.
2. Relieve pressure and disassemble air assist valve.
Refer to Supply Systems Repair-Parts manual.
43
Bleed
Stick
48
3. Clear air assist tube in platen. Clean all parts of
valve and reassemble. Refer to Supply Systems
Repair-Parts manual.
4. Remove bleed stick from platen. Push bleed stick
through bleed relieve port (T) to remove material
residue. See FIG. 30.
T
r_wm2179_313296_6a
5. Remove platen covers. See FIG. 30.
a. Remove platen cover fasteners (70) or nuts
(309).
309
b. For 55 gallon platen (D200 3 in. and D200s 6.5
in. supply systems): Remove both platen covers
(49) and ground wire from platen.
309
323
320
For smaller platens (D60 3 in. supply systems):
Disconnect pump for the platen; see Disconnect Pump from Platen, page 50. Remove
screws (323) from upper heater plate (320).
Remove upper heater plate.
6. Remove any excess fluid. Use a soft wire brush on
heater coils (48) or heater (319). See FIG. 30.
319
Bleed
Stick
T
7. Inspect platen heater blocks (43 or 320) or heater
(48 or 319) for burn or melt spots. Replace platen
heater blocks or heater if necessary. See FIG. 30.
8. Check for loose connections and damaged wires.
FIG. 30: Remove Platen Covers and Heaters
9. Follow steps in reverse order to reassemble platen.
NOTE: Torque platen cover fasteners (70) to 60 +/10 in-lbs (6.8 +/- 1.1 N•m) for 55 gallon platen.
Torque nuts (309) to 45 +/- 5 in-lbs (5.1 +/- 0.6 N•m)
for smaller platens.
313296J
33
Maintenance
Electrical Enclosure
Check Ground Fault Circuit Interrupter
1. Turn the main disconnect on the electrical control
panel door to the OFF position to disconnect power.
Power is still connected to the power line filter (459)
even after the main disconnect is open. Avoid contact with the power line filter.
1. With electrical enclosure door still open, switch main
disconnect (421) back on.
Have a qualified electrician restore power to main
disconnect while electrical enclosure door is open.
2. Press Test button on ground fault circuit interrupter
(419). The blue switch should flip to the middle or
opposite side.
2. Open door of electrical enclosure.
459
NOTE: Do not perform this test while the system is
in operation.
3. Press blue switch back into place to reset breaker.
419
419
421
FIG. 31: Inside View of Electrical Enclosure
FIG. 32: Ground Fault Circuit Interrupter
3. Check for damaged or loose wires. Check connections from cable track.
34
4. Switch main disconnect off.
313296J
Maintenance
Pump Heaters
4. Check for damaged wires and connections.
1. Turn the main disconnect on the electrical control
panel door to the OFF position to disconnect power.
5. Ensure heaters (44 or 227) are secure so they cannot rotate on pump.
2. Remove four screws (80 or 257) from back pump
shroud (52 or 234).
D200 Shown
D200 Shown
44 or 227
80 or 257
FIG. 34: Pump Heaters
FIG. 33: Remove Pump Shroud
3. Remove pump heater front shroud (51 or 233).
313296J
35
Alarms
Alarms
Warm Melt alarms alert you to a problem and help prevent system shutdown or application errors. If an alarm
occurs, operation may stop and the following occurs.
•
Light tower indication changes (if equipped)
•
Status bar on the display shows the alarm description
Diagnose Alarms
See Alarm Codes and Troubleshooting, page 36, for
causes and solutions to each alarm code.
Clear Alarms
Alarms are cleared by the solution(s) listed in the following table or from the screen in which they appear. Refer
to Alarm Codes and Troubleshooting, page 36, for
details.
Alarm Codes and Troubleshooting
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Fluid Control Module
CB1X
A - Communication Error Ram A Not Found
Ram cannot communicate with Verify that power is supFCM A.
plied.
Alarm automatically
cleared by solution.
Check that CAN cables are
connected.
Verify that selector switch
is set correctly.
Replace FCM A.
CB2X
B - Communication Error Ram B Not Found
Ram cannot communicate with Verify that power is supFCM B.
plied.
Alarm automatically
cleared by solution.
Check that CAN cables are
connected.
Verify that selector switch
is set correctly.
Replace FCM B
B61X
Crossover Error (Ram A)
B62X
Crossover Error (Ram B)
Inactive ram has a Not Primed Set inactive ram to Prime
Cleared from Ram Alarm
alarm.
mode to automatically clear screen. See Appendix A alarm.
User Interface Display,
There is a Runaway alarm
Correct runaway condition page 93.
and clear alarm on Status
screen 1.
There is a Drum Empty alarm. Replace empty drum with
full drum to clear.
36
313296J
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Fluid Control Module (continued)
DA1X
Pump Runaway A
DA2X
Pump Runaway B
Pump is running faster than
set runaway limit due to:
Correct runaway condition
and clear alarm.
Cleared from Ram Alarm
screen. See Appendix A User Interface Display,
page 93.
Drum empty sensor has been
activated.
Replace empty drum with
full drum to clear.
Alarm automatically
cleared by solution.
The pump is not primed.
Set ram to Prime mode to
automatically clear alarm,
or manually clear alarm
from Ram Alarm screen.
Cleared from Ram Alarm
screen or Ram Operation
screen. See Appendix A User Interface Display,
page 93.
Solenoid unplugged.
Check that solenoid cable
is connected.
Alarm automatically
cleared by solution.
Damaged solenoid / wires.
Inspect solenoid wires for
damage.
Alarm automatically
cleared by solution.
•
•
•
•
L11X
A - Drum Empty
L12X
B - Drum Empty
DB1X
A - Not Primed
DB2X
B - Not Primed
WJ1X
A - Air Solenoid Disconnected
WJ2X
B - Air Solenoid Disconnected
DK1X
A - Air Motor Sensor Error
DK2X
B - Air Motor Sensor Error
Increased air pressure.
Increased fluid output.
Exhausted fluid supply.
Open fitting, hose, drain,
or bleed valve.
System has seen multiple up See air motor manual.
strokes without a down stroke,
or multiple down strokes without an up stroke.
Damaged or disconnected air
motor sensors.
Cleared from Ram Alarm
screen. See Appendix A User Interface Display,
page 93.
Check that air motor sensors are connected.
Inspect air motor sensor
harness for damage.
L21X
A - Drum Low Deviation
L22X
B - Drum Low Deviation
WK1X
A - Fluid Solenoid Disconnected Deviation
WK2X
B - Fluid Solenoid Disconnected Deviation
ML1X
A - Rebuild Platen Seals
ML2X
B - Rebuild Platen Seals
MA1X
A - Rebuild Pump
MA2X
B - Rebuild Pump
313296J
Drum low sensor has been
activated.
Replace empty drum with
full drum to clear.
Deviation automatically
cleared by solution.
Solenoid unplugged.
Check that solenoid cable
is connected.
Deviation automatically
cleared by solution.
Damaged solenoid wires.
Inspect solenoid cable for
damage.
Counter has reached programmed platen maintenance
interval.
Perform platen mainteCleared from Maintenance
nance; see Supply Sysscreen. See Appendix A tems Repair-Parts manual. User Interface Display,
page 93.
Counter has reached programmed pump maintenance
interval.
Perform pump maintenance. See Check-Mate
Displacement Pump manual.
Cleared from Maintenance
screen. See Appendix A User Interface Display,
page 93.
37
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Fluid Control Module (continued)
DA1X
Pump Runaway A
DA2X
Pump Runaway B
Pump is running faster than
set runaway limit due to:
Correct runaway condition
and clear alarm.
Cleared from Ram Alarm
screen. See Appendix A User Interface Display,
page 93.
Drum empty sensor has been
activated.
Replace empty drum with
full drum to clear.
Alarm automatically
cleared by solution.
The pump is not primed.
Set ram to Prime mode to
automatically clear alarm,
or manually clear alarm
from Ram Alarm screen.
Cleared from Ram Alarm
screen or Ram Operation
screen. See Appendix A User Interface Display,
page 93.
Solenoid unplugged.
Check that solenoid cable
is connected.
Alarm automatically
cleared by solution.
Damaged solenoid / wires.
Inspect solenoid wires for
damage.
Alarm automatically
cleared by solution.
•
•
•
•
L11X
A - Drum Empty
L12X
B - Drum Empty
DB1X
A - Not Primed
DB2X
B - Not Primed
WJ1X
A - Air Solenoid Disconnected
WJ2X
B - Air Solenoid Disconnected
DK1X
A - Air Motor Sensor Error
DK2X
B - Air Motor Sensor Error
Increased air pressure.
Increased fluid output.
Exhausted fluid supply.
Open fitting, hose, drain,
or bleed valve.
System has seen multiple up See air motor manual.
strokes without a down stroke,
or multiple down strokes without an up stroke.
Damaged or disconnected air
motor sensors.
Cleared from Ram Alarm
screen. See Appendix A User Interface Display,
page 93.
Check that air motor sensors are connected.
Inspect air motor sensor
harness for damage.
38
L21X
A - Drum Low Deviation
L22X
B - Drum Low Deviation
WK1X
A - Fluid Solenoid Disconnected Deviation
WK2X
B - Fluid Solenoid Disconnected Deviation
ML1X
A - Rebuild Platen Seals
ML2X
B - Rebuild Platen Seals
MA1X
A - Rebuild Pump
MA2X
B - Rebuild Pump
Drum low sensor has been
activated.
Replace empty drum with
full drum to clear.
Deviation automatically
cleared by solution.
Solenoid unplugged.
Check that solenoid cable
is connected.
Deviation automatically
cleared by solution.
Damaged solenoid wires.
Inspect solenoid cable for
damage.
Counter has reached programmed platen maintenance
interval.
Perform platen mainteCleared from Maintenance
nance; see Supply Sysscreen. See Appendix A tems Repair-Parts manual. User Interface Display,
page 93.
Counter has reached programmed pump maintenance
interval.
Perform pump maintenance. See Check-Mate
Displacement Pump manual.
Cleared from Maintenance
screen. See Appendix A User Interface Display,
page 93.
313296J
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Fluid Control Module (continued)
DD1X
A - Pump Diving
DD2X
B - Pump Diving
Pump leak.
Ram air pressure set too low.
Worn valve or packings.
Cleared from Ram Alarm
See Check-Mate Displace- screen. See Appendix A ment Pump manual.
User Interface Display,
page 93.
Increase air pressure to
ram until diving stops.
Material flow rate exceeds
ability of ram to feed pump.
Decrease pump air pressure to slow cycle rate.
Decrease pressure until
diving stops.
Temperature Control Modules
The last digit in the temperature control module alarm codes identify the heat zone.
T3A1
T3A2
T3A3
T3A4
T3A5
T3A6
T3A7
T3A8
T3A9
T3A10
T3A11
T3A12
Alarm Above Setpoint
T2A1
T2A2
T2A3
T2A4
T2A5
T2A6
T2A7
T2A8
T2A9
T2A10
T2A11
T2A12
Deviation Below Setpoint
RTD on wrong module.
Verify RTD wire and heater Cleared from Heat Run
power cord is attached to
screen. See Heat Run
correct heat module.
Screen, page 101.
Shorted module.
Replace module.
Tripped circuit breaker.
Visually check circuit
Cleared from Heat Run
breaker for a tripped condi- screen. See Heat Run
tion.
Screen, page 101.
Low power.
Measure voltage across
input terminals on power
line filter. Voltage should
measure between 190 and
250 Vac.
Cable unplugged/loose wire.
Check for loose or disconnected wires and plugs.
Circuit breaker not set for L2
and L3.
Visually check circuit
breaker for proper setting
of L2 and L3.
Bad heaters.
Measure resistance of
heater.
GFCI has been tripped.
Visually check GFCI for a
tripped condition.
Deviation Above Setpoint
Customer supplied main circuit Measure voltage across the
breaker tripped.
disconnect switch. Voltage
should measure between
190 and 275 Vac.
313296J
39
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Temperature Control Modules (continued)
T6A1
T6A2
T6A3
T6A4
T6A5
T6A6
T6A7
T6A8
T6A9
T6A10
T6A11
T6A12
No Temp Rise
Tripped circuit breaker.
Visually check circuit
Cleared from Heat Run
breaker for a tripped condi- screen. See Heat Run
tion.
Screen, page 101.
Low power.
Measure voltage across
input terminals on power
line filter. Voltage should
measure between 190 and
250 Vac
Cable unplugged/loose wire.
Check for loose or disconnected wires and plugs.
Circuit breaker not set for L2
and L3.
Visually check circuit
breaker for proper setting
of L2 and L3.
Bad heater(s).
Measure resistance of
heater(s).
GFCI has been tripped.
Visually check GFCI for a
tripped condition.
Customer supplied main circuit Measure voltage across the
breaker tripped.
disconnect switch. Voltage
should measure between
190 and 275 Vac.
A4A1
A4A2
A4A3
A4A4
A4A5
A4A6
A4A7
A4A8
A4A9
A4A10
A4A11
A4A12
40
Over current
Bad heaters.
Measure resistance of
heater.
Wrong zone type.
Ensure zone is set for type
of hardware connected to
it.
High voltage.
Measure voltage across the
disconnect switch. Voltage
should measure between
190 and 275 Vac.
Shorted module.
If temperature rises for a
zone that has been disabled, replace heat module.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
313296J
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Temperature Control Modules (continued)
A1A1
A1A2
A1A3
A1A4
A1A5
A1A6
A1A7
A1A8
A1A9
A1A10
A1A11
A1A12
Undercurrent
Tripped circuit breaker.
Visually check circuit
Cleared from Heat Run
breaker for a tripped condi- screen. See Heat Run
tion.
Screen, page 101.
Over temperature protection is Allow zone to cool down.
activated.
Low power.
Measure voltage across
input terminals on power
line filter. Voltage should
measure between 190 and
250 Vac.
Cable unplugged/loose wire.
Check for loose or disconnected wires and plugs.
Circuit breaker not set for L2
and L3.
Visually check circuit
breaker for proper setting
of L2 and L3.
Bad heaters.
Measure resistance of
heater.
GFCI has been tripped.
Visually check GFCI for a
tripped condition.
Customer supplied main circuit Measure voltage across the
breaker tripped.
disconnect switch. Voltage
should measure between
190 and 250 Vac.
Wrong zone type.
Ensure zone is set for type
of hardware connected to
it.
A7A1
A7A2
A7A3
A7A4
A7A5
A7A6
A7A7
A7A8
A7A9
A7A10
A7A11
A7A12
Unexpected Current
Shorted module.
If temperature rises for a
zone that has been disabled, replace heat module.
T6A1
T6A2
T6A3
T6A4
T6A5
T6A6
T6A7
T6A8
T6A9
T6A10
T6A11
T6A12
Invalid RTD Reading
Bad RTD.
Measure resistance of RTD Cleared from Heat Run
and verify it is within valid
screen. See Heat Run
range.
Screen, page 101.
Bad RTD connection/loose
wire.
Check for loose or disconnected wires and plugs.
Component not plugged in.
Ensure a component is
plugged into zone reporting error. If nothing is
plugged in, disable zone.
313296J
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
41
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
T4C1
T4C2
T4C3
T4C4
T4C5
T4C6
T4C7
T4C8
T4C9
T4C10
T4C11
T4C12
PCB Overtemperature
Overheated Temperature
Control Module.
Turn heat zone off. Wait a
few minutes. If the condition does not clear on its
own, replace heater module.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
V4M1
V4M2
V4M3
V4M4
V4M5
V4M6
V4M7
V4M8
V4M9
V4M10
V4M11
V4M12
High Line Voltage
Incoming line voltage is too
high.
Measure voltage across
disconnect switch. Voltage
should measure between
190 and 250 Vac.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
V1M1
V1M2
V1M3
V1M4
V1M5
V1M6
V1M7
V1M8
V1M9
V1M10
V1M11
V1M12
No Line Voltage
Low Line Voltage
Tripped circuit breaker.
Cleared from Heat Run
Visually check circuit
breaker for a tripped condi- screen. See Heat Run
tion.
Screen, page 101.
GFCI has been tripped.
Visually check GFCI for a
tripped condition.
Cable unplugged/loose wire.
Check for loose or disconnected wires and plugs.
V4I1
V4I2
V4I3
V4I4
V4I5
V4I6
V4I7
V4I8
V4I9
V4I10
V4I11
V4I12
High DC Voltage
Faulty DC power supply.
Measure that DC supply
output is 24V. If not,
replace supply.
42
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
313296J
Alarms
Alarm
Code
Alarm Problem
Cause
Solution
Clear Alarm
Temperature Control Modules (continued)
V1I1
V1I2
V1I3
V1I4
V1I5
V1I6
V1I7
V1I8
V1I9
V1I10
V1I11
V1I12
Low DC Voltage
A4C1
A4C2
A4C3
A4C4
A4C5
A4C6
A4C7
A4C8
A4C9
A4C10
A4C11
A4C12
Faulty DC power supply.
Measure that DC supply
output is 24V. If not,
replace supply.
Broken Temperature Control
Module.
If DC supply is supplying
24V when disconnected
from system, check which
module is causing short.
Check this by connecting
one module at a time and
then measuring for 24V.
High Contactor Current
Broken contactor.
Replace contactor.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
A1C1
A1C2
A1C3
A1C4
A1C5
A1C6
A1C7
A1C8
A1C9
A1C10
A1C11
A1C12
Low Contactor Current
Broken contactor.
Replace contactor.
Disconnected or loose wire.
Verify cable 15W902 from
High Power Temperature
Control Module is connected correctly.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
Broken Temperature Control
Module.
Verify there is 24V between
both wires on 15W902. If
there is not 24V, replace
High Power Temperature
Control Module.
A7C1
A7C2
A7C3
A7C4
A7C5
A7C6
A7C7
A7C8
A7C9
A7C10
A7C11
A7C12
Unexpected Contactor Cur- Broken Temperature Control
rent
Module.
Turn heat zone for platen
off. If there is still 24V
across wires on 15W902,
replace Temperature Control Module.
313296J
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
Cleared from Heat Run
screen. See Heat Run
Screen, page 101.
43
Troubleshooting
Troubleshooting
1. Follow Pressure Relief Procedure, page 28,
before disassembling any part of the warm melt
supply system.
NOTE: Troubleshooting covered in this manual is
specific to warm melt heat functions. Refer to Supply Systems Repair-Parts manual and/or Tandem
Supply Systems Repair-Parts manual for ram troubleshooting. Refer to Check-Mate Pump Packages
manual for pump troubleshooting.
Problem
No power.
No graphics on screen.
Cause
2. Disconnect all power to the warm melt supply system before repairing.
3. Check all possible problems before disassembling
any part of the warm melt supply system.
Verification
Solution
Customer supplied main
circuit breaker tripped.
Measure voltage across
disconnect switch; voltage
should measure between
190 and 250 Vac.
Determine cause of the
tripped circuit breaker.
Then repair fault and reset
main circuit breaker.
GFCI has been tripped.
Visually check GFCI for a
tripped condition.
Determine fault that caused
GFCI to trip. Then repair
fault and reset GFCI.
No graphics are shown on
display screen.
Verify green LED on bottom If green LED is not illumiof display is illuminated.
nated:
3
24 Rtn
2
24 Vdc+
GCA cable end
1. Check for DC power on
the GCA cable at the
display. Replace faulty
cable/component.
2. Replace faulty display
module.
If green LED is illuminated,
check red LED. If red LED
is illuminated, replace display module.
Backlight does not power
up.
44
Can see display, but back- Replace display module.
light is not illuminated when
a button is pressed.
313296J
Troubleshooting
Problem
No heat.
Cause
Verification
Solution
Tripped circuit breaker.
Visually check circuit
Determine cause of tripped
breaker for a tripped condi- circuit breaker. Then repair
tion.
fault and reset main circuit
breaker.
Low power.
Measure voltage across
terminals 2T1 and 4T2 on
main disconnect. Voltage
should measure between
190 and 275 Vac.
1. If voltage is lower than
expected, use electrical
schematic to locate
faulty wiring or connection.
2. Have a qualified electrician service electrical
components.
Cable unplugged/loose
wire.
Check for loose or disconnected wires and plugs.
Attach plug/wire.
GFCI tripped.
Visually check GFCI for a
tripped condition.
Determine fault that caused
GFCI to trip. Repair fault,
and reset GFCI.
Zone not enabled.
Verify zone is enabled on
Heat Run screen.
Enter Setup screen and
enable correct zone.
Incorrect temperature set
point.
Verify zone has a correct
temperature setting on
Heat Run screen.
Enter Setup and enter correct temperature.
Bad heater.
Measure resistance of
heater.
1. Unplug suspected
heater zone from
heater module.
2. Follow Heater Resistance Checks, page
22.
3. If resistance is outside
allowable value,
replace heater(s).
Contactor not closing.
Turn on heat for zone A1 or 1. Verify cable 15W902
B1and ensure contactor
from the high power
closes.
TCM is connected correctly.
2. Verify that there are no
other error conditions
that would prevent
heater from starting.
3. Verify there is 24 Vdc
between 2 wires on
15W902. If not, replace
high power TCM. See
Alarms, page 36.
4. Replace contactor.
313296J
45
Troubleshooting
Problem
Missing module.
Cause
Verification
Solution
Modules not on network.
Verify attached modules
through Advanced Setup
screens 4 and 5.
Enter Setup screen and
scroll to Advanced Setup
screens 4 and 5. These
screens lists all components corresponding software revision number on
network.
Cable disconnected.
Verify all green LEDs are
illuminated and yellow
LEDs are flashing.
Reconnect/replace faulty
cable.
Module with wrong rotary
switch setting.
Verify rotary switch is set
correctly.
1. Remove power from
unit.
2. Remove access cover
and visually check
rotary switch setting.
3. If incorrect, set to correct setting. See
Upgrade Temperature Control Module
Software, page 56,
and Upgrade FCM
Software, page 59, for
selector switch locations.
4. Replace access cover.
Heating is slow.
Heater defective.
Measure resistance of
heater.
Follow Heater Resistance
Checks, page 22.
Low power.
Measure voltage across
terminals 2T1 and 4T2 on
main disconnect. Voltage
should measure between
190 and 275 Vac.
1. If voltage is lower than
expected, use electrical
schematic to locate
faulty wiring or connection.
2. Have a qualified electrician service electrical
components.
Heating over shoots.
RTD on wrong module.
Shorted module.
Does not crossover.
46
Verify for given zone that
temperature does not
increase when zone is disabled.
Verify RTD wire or heater
power cord is attached to
correct heat module.
Replace module.
Alternate ram has an empty Verify ram has material.
sensor activated.
Replace empty drum.
Alternate pump is not
primed.
Verify alternate ram is
ready to run.
Prime pump.
Alternate pump has an
active alarm.
See Alarm Codes and
Troubleshooting, page
36.
See Alarm Codes and
Troubleshooting, page
36.
313296J
Repair
Repair
To reduce the risk of serious injury, follow the Pressure Relief Procedure and the Load Material procedure prior to performing repair procedures.
For smaller platens (D60 3 in. supply systems):
Remove junction box. Remove screws (278) from junction box (255), and remove cover (271). Remove junction box from bracket (258).
Air Motor
Remove Air Motor
Remove junction box.
For 55 gallon platen (D200 and D200s supply systems):
Remove two screws (61) securing junction box to air
motor. Remove junction box and temporarily secure to
platen rod.
42
258
255
271
278
FIG. 36: Remove D60 Junction Box
61
71
3. See Disconnect Displacement Pump in
Check-Mate Pump Packages manual.
96
90, 91
FIG. 35: Remove D200 and D200s Junction Box
12
To reduce the risk of serious injury or damage to
equipment, make sure the main disconnect is off
before continuing with this procedure.
4. See Supply System repair manual for air motor
removal instructions.
313296J
47
Repair
Install Air Motor
shrouds (51, 52), pump heaters (44), and RTD sensor (46).
2. Reinstall junction box.
For 55 gallon platen (D200 and D200s supply systems): Remove junction box from platen rod. Reinstall junction box to air motor using move two
screws (61). See FIG. 35.
For smaller platens (D60 3 in. supply systems):
Reinstall junction box (255) onto bracket (258). Use
screws (278) to attach cover (271). See FIG. 36.
Displacement Pump
r_wm2179_313296_7a
1. See Supply System repair manual for air motor
installation instructions.
51
44
46
44
52
FIG. 37: D200 and D200s Pump Heater Shrouds
Remove Displacement Pump
This procedure must be done while the system is still
warm. The material and equipment may still be hot.
4. Raise air motor. Loosen nut (HB) under ram bar and
thread it down the threaded rod (HC) to the lift ring
adapter (HD) holding the motor. Use wrench on nut
(HA) on top of ram bar to raise air motor.
HC
Refer to your Check-Mate Displacement Pump manual
to repair the displacement pump.
If the air motor does not require servicing, leave it
attached to its mounting. If the air motor does need to
be removed, see Remove Air Motor, page 47.
HA
D200 and D200s Supply Systems
HB
HD
1. Disconnect air hose and ground wire from air motor.
2. See Disconnect Displacement Pump in
Check-Mate Pump Packages manual.
3. Follow steps 1- 4 of Replace Platen Heaters and
Sensor section, page 52, to remove pump heater
TI10648A
FIG. 38: Raise Air Motor
5. See Disconnect Pump from Platen, page 50, to
disconnect the displacement pump from the platen.
6. Use two people to carefully lift out the displacement
pump. Service displacement pump as needed. See
Check-Mate Displacement Pump manual for
instructions.
48
313296J
Repair
D60 Supply System
1. Disconnect air hose and ground wire from air motor.
2. See Disconnect Displacement Pump in
Check-Mate Pump Packages manual.
r_wm29yy_313296b_3
3. Follow steps 1- 4 of Replace Platen Heaters and
Sensor section, page 52, to remove pump heater
shrouds (233, 234), pump heaters (227), and RTD
sensor (229).
227
229
Install Displacement Pump
D200 and D200s Supply Systems
1. Install displacement pump on platen. See Connect
Pump to Platen, page 51.
2. Lower air motor. Use wrench on nut (EA) to lower
air motor.
3. Reinstall pump heater shrouds (51, 52). Secure with
screws (80).
4. See Reconnect Displacement Pump in
Check-Mate Pump Packages manual.
5. Reconnect air hose and ground wire to air motor.
227
233
FIG. 39: D60 Pump Heater Shrouds
TI10515A
FIG. 40: Reconnect Air Hose and Ground Wire
4. See to Disconnect Pump from Platen on page 50
to disconnect displacement pump from platen.
5. Raise ram assembly to lift air motor away from displacement pump.
6. Remove displacement pump, and service as
needed. See Check-Mate Displacement Pump
manual.
D60 Supply System
1. Raise ram to install displacement pump to platen.
2. Connect displacement pump to platen. See Connect Pump to Platen, page 51.
3. Reinstall pump heater shrouds (233, 234). Secure
with screws (257).
4. See Reconnect Displacement Pump in
Check-Mate Pump Packages manual.
5. Reconnect air hose and ground wire to air motor.
313296J
49
Repair
Disconnect Pump from Platen
20, 30, and 60 Liter Platens
1. Disconnect displacement pump from air motor. See
Check-Mate Pump Packages manual.
The pump is mounted to the platens by mounting Kit
255392.
2. Raise air motor. See Remove Displacement
Pump, page 48.
3. Remove screws (308) from platen.
55 Gallon Platen
1. Disconnect displacement pump from air motor. See
Check-Mate Pump Packages manual.
2. Raise air motor. See Remove Displacement
Pump, page 48.
3. Remove four screws (103a) and four clamps (103b).
103a
103b
308
103c
FIG. 42: 20, 30, 60 Liter Mounting
4. Use two people to carefully lift pump from platen. If
using a pump with an intake adapter, remove
screws, adapter, and o-rings from pump inlet.
5. Inspect o-ring for damage. Replace o-ring if necessary.
FIG. 41: 55 Gallon Mounting Kit
4. Use two people to carefully lift pump from platen.
5. Inspect o-ring (103c) for damage. Replace o-ring if
necessary.
50
313296J
Repair
Connect Pump to Platen
Replace Pump Heaters
55 Gallon Platen
1. Turn off main disconnect.
1. Use two people to set pump onto platen.
2. Remove screws (80 or 257) from back pump heater
2. Secure pump to platen with screws (103a) and
clamps (103b). See FIG. 41.
3. Lower air motor.
shroud (52 or 234).
D200 Shown
4. See Reconnect Displacement Pump in
Check-Mate Pump Packages manual.
20, 30, and 60 Liter Platen
NOTE: Before installing a 20, 30, or 60 liter platen to
a pump with an intake adapter, install adapter and
o-ring.
80 or 257
52
or
234
1. Place o-ring on pump intake. See FIG. 42.
2. Use two people to set pump onto platen.
3. Secure pump to platen with screws (308).
4. Lower air motor.
5. See Reconnect Displacement Pump in
Check-Mate Pump Packages manual.
FIG. 43: Remove Pump Shroud
3. Remove ground wires.
4. Remove pump heater front shroud (51 or 233).
313296J
51
Repair
5. Remove pump heater bands (44 or 227):
a. Remove screws from both pump heaters.
Replace Platen Heaters and
Sensor
b. Pry heater bands apart and remove from pump.
c.
Disconnect wires from heater bands. Inspect
wires for damage, and replace with new wires
(included with pump heaters) if necessary. See
Electrical Schematics, page 61.
d. Remove RTD sensor (46 or 229). Loosen screw
on sensor support (45 or 228) and slide RTD
out.
55 Gallon Platen Heater and Sensor
1. Turn off main disconnect.
2. Remove both platen cover fasteners (70).
3. Remove both platen covers (49) and ground wire
from platen.
70
49
44 or 227
45 or 228
46 or 229,
110
43
59
44 or 227
11
64
ti17720a
FIG. 44: Remove Pump Heaters
109
6. Install new pump heater bands and secure with
screws.
58
ti18061a
82
FIG. 45: Replace Platen Heaters and RTD Sensor
NOTE: To ease pump heater band installation, first
install heater bands on middle of displacement
pump. Then slide heater band up or down into correct location.
4. Remove platen heater blocks (43).
7. Reinstall RTD sensor and tighten screw on sensor
support.
a. Use a hex wrench to remove three nuts (59)
and washers (11, 64) from each heater block.
NOTE: Ensure RTD is flush to pump before tightening screw.
b. Remove screws (12) from junction box cover
(96). Loosen strain relief nut (91), and remove
junction box cover.
8. Reinstall pump heater front shroud.
c.
9. Reinstall ground wires.
Disconnect four platen heater wires (labeled A
dn B) and RTD sensor connector in the terminal
box. See Electrical Schematics, page 61.
10. Reinstall back pump heater shroud, and secure with
screws.
52
313296J
Repair
d. Remove screws (58) and washers (82).
Remove platen heater blocks (43) and RTD
sensor (46).
324
5. Install new platen heaters and RTD sensor. Secure
RTD sensor with screw and washer. Secure platen
heater blocks with nuts and washers.
323
320
6. Label platen heater wires A and B as shown on
page 64. Reroute platen heater wires and platen
RTD sensor through the conduit to the junction box.
Reconnect the four wires to the appropriate terminal
block A and B. Reconnect the platen RTD sensor.
319
318
7. Reinstall junction box cover. Secure with screws
and tighten strain relief nut.
309
8. Reconnect ground wire, and install platen covers.
Secure platen covers with fasteners. Torque platen
cover fasteners to 60 in-lbs +/- 10 in-lbs (6.8 +/- 1.1
N•m)
Air Fitting
Assembly
9. Reconnect displacement pump using screws and
clamps.
20, 30, and 60 Liter Platen Heater
1. Disconnect pump from platen.
2. Remove platen heater block (320).
a. Remove screws (278) from junction box cover
(271), and remove junction box cover. See page
86.
b. Remove strain relief nut (265) from junction box
to allow space for wires. See page 86.
c.
Remove air fitting assembly from platen.
ti17717b
FIG. 46: Replace Platen Heaters
3. Remove platen heater (319).
a. Disconnect two platen heater wires (labeled A
and B) in the terminal box. See D60 Junction
Box Schematic, page 71.
b. Remove platen and heater (319).
4. Install new platen heater (319) to lower heater plate
(318). Install upper heater plate (320). Reconnect
ground wire, and secure with screws.
d. Remove nuts (309) from the heat shield guard
(324).
5. Label platen heater wires A and B as shown on
page page 70. Reroute platen heater wires through
the conduit to the junction box. Reconnect the two
wires to the appropriate terminal block A and B.
e. Remove screws (323) from upper heater plate
(320). Remove upper heater plate and ground
wire.
6. Reinstall heat shield guard. Secure with nuts.
Torque nuts to 45 +/- 5 in-lbs (5.1 +/- 0.6 N•m).
7. Reconnect displacement pump using screws and
clamps.
8. Reinstall junction box cover and strain relief nut.
Secure cover with screws.
313296J
53
Repair
Replace Platen Wipers
Refer to Supply Systems Repair-Parts manual for
instructions.
Replace Ram Piston Rod Seals
1. Support electrical enclosure (13 or 14) using a loop
and a hoist.
2. Remove screws from bracket (50 or 232) connecting electrical enclosure (13 or 14) to ram piston rod
and cable track (42, if applicable).
42
13 or 14
50 or 232
FIG. 47: Replace Rod Seals
3. For 55 gallon platen (D200 and D200s supply systems): Gently move cable track (42) and bracket
(50) to side.
For smaller platens (D60 supply systems): Remove
bracket (232).
4. See Supply Systems Repair-Parts manual for
replacement instructions.
5. Follow steps in reverse order to reinstall bracket,
cable track (if applicable), and the electrical enclosure.
54
313296J
Repair
Electrical Enclosure
408
Prior to repairing any component of the electrical enclosure (13 or 14), turn the main disconnect on the electrical control panel door to the OFF position to disconnect
power.
Outbound
Power
RTD
411
Power is still connected to the power line filter (459)
even after the main disconnect is open. Avoid contact with the power line filter.
Replace Low Power Temperature Control
Module(s)
1. Open enclosure door (402). Disconnect the following cables from low power TCM (408):
•
•
•
incoming power supply cable (430)
outbound power supply cable (see FIG. 49)
RTD cable
Outbound
Power
RTD
FIG. 49: Back View of Electrical Enclosure
2. Loosen both captive screws (409) holding low
power TCM (408) to base (407); remove low power
TCM. See FIG. 48.
3. Follow steps in reverse order to install new low
power TCM.
4. Upload the correct TCM software for the system.
See Upgrade Temperature Control Module Software, page 56, for instructions.
459
Captive
Screw
430
408
Captive
Screw
411
428
431
429
432
FIG. 48: Internal View of Electrical Enclosure
313296J
55
Repair
Replace Base
1. Remove low power TCM. See Replace Low Power
Temperature Control Module(s).
2. Disconnect two CAN cables from base (407).
3. Remove four screws (409) and ground screw (410)
from base.
NOTE: Reuse brackets (412, 413) to install new high
power TCM.
6. Upload the correct TCM software from kit 16C027.
See Upgrade Temperature Control Module Software, page 56, for instructions.
7. Remove cover of new high power TCM and set
selector switch to “0” for Ram A or “1” for Ram B.
4. Replace with new base and secure with screws.
5. Reconnect two CAN cables to base.
6. Set selector switch to:
•
•
•
•
•
•
Selector
Switch
“0” for TCM labeled “2” on Ram A
“1” for TCM labeled “3” on Ram A
“2” for TCM labeled “4” on Ram A
“5” for TCM labeled “2” on Ram B
“6” for TCM labeled “3” on Ram B
“7” for TCM labeled “4” on Ram B
TI12360a
FIG. 51: Set Selector Switch
Selector
Switch
TI12361a
FIG. 50: Set Selector Switch
7. Reinstall low power TCM. See Replace Low Power
Temperature Control Module(s).
Upgrade Temperature Control Module
Software
NOTE: Order kit 16C027 for an upgrade token. See
Graco Control Architecture™ Module Programming
manual for instructions.
NOTE: Reuse brackets (412, 413) to install new high
power TCM.
Replace High Power Temperature Control
Module
1. Open enclosure door (402). Disconnect outbound
power supply and RTD cables from high power
TCM (411). See FIG. 49.
2. Remove electrical enclosure side panel (436). See
Electrical Enclosure Parts on page 90.
3. Disconnect all four incoming cables (432, 428, 429,
431) from high power TCM. See FIG. 48.
4. Remove both screws (415) that secure brackets
(412, 413) of high power TCM to electrical enclosure. Remove high power TCM. See Electrical
Enclosure Parts on page 90.
5. Follow steps in reverse order to install new high
power TCM.
56
313296J
Repair
Replace Circuit Breakers
1. Open enclosure door (402). Disconnect wires from
circuit breaker (417, 419).
2. Push in circuit breaker tab and pull out breaker.
4. Remove screws (12 or 202) and washers (11 or
201) from bottom bracket (39 or 222) and side
bracket (50 or 232) of enclosure.
D200 Shown
plug
11 or 201,
12 or 202
417
50 or 232
13 or 14
419
417
39 or 222
FIG. 52: Circuit Breakers
FIG. 53: Replace Electrical Enclosure
3. Replace with new circuit breaker. Use tabs on bottom of breaker to select L2 and L3.
5. Lift enclosure off and replace with new enclosure.
4. Snap new circuit breaker into place and reconnect
wires.
Replace Electrical Enclosure
6. Secure new electrical enclosure to bottom and side
brackets with screws and washers.
7. Reconnect heater and RTD cables to each TCM.
8. Reconnect power to power line filter.
1. Ensure power to electrical enclosure is disconnected.
2. Disconnect heater and RTD cables from each TCM.
3. Remove plug and use lift ring (not included) at top of
electrical enclosure (13 or 14).
313296J
Have a qualified electrician reinstall main incoming
power to system and electrical enclosure.
57
Repair
Display/User Interface
Upgrade Display Software
NOTICE
To avoid damaging circuit board, wear a grounding
strap.
NOTE: Order kit 16C027 for an upgrade token. See
Graco Control Architecture™ Module Programming
manual for instructions.
Replace Display
NOTE: Order Kit 24F493 for replacement. Software
token 16C027 is required to install software before
use.
NOTICE
To avoid damaging circuit board, wear a grounding
strap.
1. Disconnect power.
2. Pull display (20) out of bracket (22) clips to remove
it.
3. Disconnect CAN cable(s) from display (20).
4. Replace with new display. Reconnect CAN cable(s).
5. Load the correct display software for the system.
Follow the steps in Upgrade Display Software on
page 58.
NOTE: Token is not included with display and must
be ordered separately.
58
313296J
Repair
Replace Fluid Control Module
41 or 224
1. Disconnect power to system.
Captive
Screws
30 or
217
2. Remove front shroud (16 or 204) and back shroud
(17 or 205).
D200 Shown
16 or 204
33 or
219
36 or
220
28 or 215
FIG. 55: Remove FCM
6. Replace with new FCM, and secure with screws.
7. Reconnect cables to FCM.
8. Load the correct FCM software for the system. Follow the steps in Upgrade FCM Software on page
59.
Replace Base
17 or 205
FIG. 54: Remove Shrouds
3. Disconnect all cables from FCM (36 or 220).
1. Disconnect power to system.
2. Remove FCM (36 or 220). See Replace Fluid Control Module.
3. Disconnect CAN cable(s) from FCM (36 or 220).
4. Remove access door (41 or 224).
4. Remove screws (28 or 215) and ground screw (30
or 217) from base (33 or 219). See FIG. 55.
5. Loosen both captive screws from FCM and pull
FCM off base (33 or 219).
5. Replace with new base, and secure with screws.
6. Reconnect CAN cable(s).
7. Set selector switch to “A” for Ram A or “B” for Ram
B. See FIG. 55.
8. Reinstall FCM. See Replace Fluid Control Module.
Upgrade FCM Software
NOTE: Order kit 16C027 for an upgrade token. See
Graco Control Architecture™ Module Programming
manual for instructions.
313296J
59
Repair
Replace Cable Track
D200 and D200S Supply Systems Only
NOTE: Order Kit 257163 for replacement.
1. Disconnect power to system.
2. Disconnect all 10 cables from back of electrical
enclosure (13 or 14).
4. Remove screws (12) from junction box cover (96)
and junction box (78).
5. Loosen strain relief nut (90), and remove junction
box cover.
6. Disconnect all wires in junction box. Pull wires out of
strain relief.
7. Remove mounting screws (71), washer (72), and
nut (73) securing cable track assembly (42) to junction box.
42
72
73
61
FIG. 56: Back View of Electrical Enclosure
71
96
3. Remove screws (71) from bracket (50) that connect
cable track (42) to electrical enclosure (13 or 14)
and ram.
42
50
71
91
12
90
FIG. 58: Junction Box
8. Lift out cable track assembly and cables.
9. Replace with new cable track kit. Secure new cable
track to junction box using mounting screws.
10. Run wires through strain relief and reconnect all
wires in junction box. See D200 Junction Box
Schematic, page 65.
13 or 14
11. Reinstall strain relief nut and junction box cover.
Secure junction box using screws.
12. Reattach cable track to bracket. Use screws to
secure bracket holding cable track to electrical
enclosure and ram.
FIG. 57: Cable Track Bracket
13. Reconnect all 10 cables to back of electrical enclosure.
14. Reconnect power to system.
60
313296J
313296J
t
GUN
PLATEN
BUSS BAR
SHIELDED CABLE
KEY
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
5
5
5
Heater
Power
5
DC
CONTROL
HPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
25 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
8 Amp
Circuit
Breaker
Cable
Cable
8 Amp
C/B
50A
CONTACTOR
3
24 Rtn
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Cable
2
24 Vdc+
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
DISPLAY
MODULE
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Top Switch 1
Top Switch 2
Bottom Switch 1
Bottom Switch 2
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
Sensor Reed Switch
MEMBRAN E SW ITCH
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
CABLE TRACK
24 Vdc P/S
63A
GFCI
Warm Melt
Standard Ram
M
M
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(5)
Cable Splitter
Motor Pigtail
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
Fieldbus
Ferrite Bead
Ferrite Bead
F
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
Cable 15 Meter
Fluid Filter Monitor Option
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
F
Cable 8 Pin
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
2
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Amber (2)
Common (3)
Green (4)
Red (5)
Cable
Wire Harness
Ferrite Bead
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
M
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Gateway
Module
Gateway Option
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Power
(2) Filter Inlet Press.
(3) Common
(4) Filter Outlet Press.
(5) Drain
7
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM A
Depres/Recirc Option
F
(1)
(2)
(1) Solenoid signal
(2) Solenoid RTN
AIR SOLENOID
(1) Unused
(2) Amber
(3) Common
(4) Green
(5) Red
Light Tower
Light Tower Option
Fluid Solenoid
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
3
2
1
Cable Splitter
3
2
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
(1)
(2)
F
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
(1)
(2)
(3)
(4)
F
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
AIR SOLENOID
P/N 121235
(1) Solenoid signal
(2) Solenoid RTN
(1)
(2)
(3)
(4)
F
DRUM LOW or EMPTY OPTION
D200 Single Ram Schematic
t
PUMP
t
HOSE
t
J-BOX
Line Filter
Warm Melt Enclosure
Electrical Schematics
Electrical Schematics
D ISPL AY
61
62
t
GUN
PLATEN
BUSS BAR
SHIELDED CABLE
KEY
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
5
5
5
Heater
Power
5
DC
CONTROL
HPTCM
P/N 255774
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
25 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
8 Amp
Circuit
Breaker
Cable
Cable
8 Amp
C/B
50A
CONTACTOR
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
24 Rtn
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
DISPLAY
MODULE
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Top Switch 1
Top Switch 2
Bottom Switch 1
Bottom Switch 2
2
24 Vdc+
Cable
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
Sensor Reed Switch
MEMBRAN E SW ITCH
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
CABLE TRACK
24 Vdc P/S
63A
GFCI
Warm Melt
Ram “A”
M
M
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(5)
Cable Splitter
Motor Pigtail
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
Fieldbus
Ferrite Bead
Ferrite Bead
F
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
Cable 15 Meter
Fluid Filter Monitor Option
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
F
Cable 8 Pin
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
2
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Amber (2)
Common (3)
Green (4)
Red (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Gateway
Module
Ferrite Bead
3
2
(1)
(2)
F
(1)
(2)
(3)
(4)
AIR SOLENOID
(1) Solenoid signal
(2) Solenoid RTN
(1) Unused
(2) Amber
(3) Common
(4) Green
(5) Red
Light Tower
Light Tower Option
F
Depres/Recirc Option
Fluid Solenoid
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
Cable Splitter
Wire Harness
Ferrite Bead
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
M
Gateway Option
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Power
(2) Filter Inlet Press.
(3) Common
(4) Filter Outlet Press.
(5) Drain
7
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM A
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
|
OR
|
(1)
(2)
(3)
(4)
(5)
M
To Ram
“B”
Option
3
2
1
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
F
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
D200 Ram A Schematic
t
PUMP
t
HOSE
t
J-BOX
Line Filter
Warm Melt Enclosure
Electrical Schematics
D ISPL AY
313296J
313296J
To Ram “A”
M
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
Motor Pigtail
BUSS BAR
SHIELDED CABLE
KEY
Cable, CAN 15m
Sensor Reed Switch
Top Switch (1)
Top Switch (2)
Bottom Switch (1)
Bottom Switch (2)
M
F
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
Ferrite Bead
Cable 8 Pin
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM “B”
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
M
3
2
Fluid Solenoid
F
(1)
(2)
F
(1)
(2)
(3)
(4)
AIR SOLENOID
(1) Solenoid signal
(2) Solenoid RTN
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
Cable Splitter
Wire Harness
Depress/Recirc Option
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
(1)
(2)
(3)
(4)
(5)
M
3
2
1
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
F
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
GUN
t
PLATEN
PUMP
HOSE
t
t
t
J-BOX
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
CABLE TRACK
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
Line Filter
5
5
5
Heater
Power
DC
Control
5
4
HPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
Cable
50A
CONTACTOR
25 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
Cable
Cable
63A
GFCI
Warm Melt Enclosure
D200 Ram B
Schematic
(1)
(2)
(3)
(4)
(5)
Warm Melt
Ram “B” Option
Electrical Schematics
63
Electrical Schematics
Displacement Pump
Platen
D200 Displacement Pump and Platen Schematics
64
313296J
Electrical Schematics
D200 Junction Box Schematic
313296J
65
Electrical Schematics
D200 Cable Track Schematic
66
313296J
313296J
t
GUN
PLATEN
t
PUMP
t
HOSE
t
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
BUSS BAR
CABLE HARNESS
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
5
5
5
Heater
Power
5
DC
CONTROL
HPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
24 Vdc P/S
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
25 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
8 Amp
Circuit
Breaker
Cable
Cable
8 Amp
C/B
63A
GFCI
50A
CONTACTOR
3
24 Rtn
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Cable
2
24 Vdc+
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
DISPLAY
MODULE
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
Sensor Reed Switch
Top Switch 1
Top Switch 2
Bottom Switch 1
Bottom Switch 2
Warm Melt
D60 Standard Ram
MEMBRAN E SW ITCH
SHIELDED CABLE
KEY
J-BOX
Line Filter
Warm Melt Enclosure
M
M
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(5)
Cable Splitter
Motor Pigtail
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
Fieldbus
Ferrite Bead
Ferrite Bead
F
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
Cable 15 Meter
Fluid Filter Monitor Option
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
F
Cable 8 Pin
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
2
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Amber (2)
Common (3)
Green (4)
Red (5)
Cable
Wire Harness
Ferrite Bead
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
M
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Gateway
Module
Gateway Option
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Power
(2) Filter Inlet Press.
(3) Common
(4) Filter Outlet Press.
(5) Drain
7
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM A
Depres/Recirc Option
F
(1)
(2)
(1) Solenoid signal
(2) Solenoid RTN
AIR SOLENOID
(1) Unused
(2) Amber
(3) Common
(4) Green
(5) Red
Light Tower
Light Tower Option
Fluid Solenoid
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
3
2
1
Cable Splitter
3
2
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
(1)
(2)
F
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
(1)
(2)
(3)
(4)
F
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
AIR SOLENOID
(1) Solenoid signal
(2) Solenoid RTN
(1)
(2)
(3)
(4)
F
DRUM LOW or EMPTY OPTION
Electrical Schematics
D60 Single Ram Schematic
D ISPL AY
67
68
t
GUN
PLATEN
t
PUMP
t
HOSE
t
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
BUSS BAR
CABLE TRACK
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
5
5
5
Heater
Power
5
DC
CONTROL
HPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
24 Vdc P/S
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
25 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
8 Amp
Circuit
Breaker
Cable
Cable
8 Amp
C/B
63A
GFCI
50A
CONTACTOR
3
24 Rtn
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
Power (1)
Unused (2)
Common (3)
Press Signal (4)
Fluid Pressure Sensor
2
24 Vdc+
Cable
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
Sensor Reed Switch
Top Switch 1
Top Switch 2
Bottom Switch 1
Bottom Switch 2
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
DISPLAY
MODULE
Warm Melt
D60 Ram “A”
MEMBRAN E SW IT CH
SHIELDED CABLE
KEY
J-BOX
Line Filter
Warm Melt Enclosure
M
M
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(5)
Cable Splitter
Motor Pigtail
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
Fieldbus
Ferrite Bead
Ferrite Bead
F
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
Cable 15 Meter
Fluid Filter Monitor Option
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
F
Cable 8 Pin
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
2
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Amber (2)
Common (3)
Green (4)
Red (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Gateway
Module
Ferrite Bead
3
2
(1)
(2)
F
(1)
(2)
(3)
(4)
AIR SOLENOID
(1) Solenoid signal
(2) Solenoid RTN
(1) Unused
(2) Amber
(3) Common
(4) Green
(5) Red
Light Tower
Light Tower Option
F
Depres/Recirc Option
Fluid Solenoid
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
Cable Splitter
Wire Harness
Ferrite Bead
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
M
Gateway Option
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Power
(2) Filter Inlet Press.
(3) Common
(4) Filter Outlet Press.
(5) Drain
7
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM A
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
|
OR
|
(1)
(2)
(3)
(4)
(5)
M
To Ram
“B”
Option
3
2
1
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
F
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
Electrical Schematics
D60 Ram A Schematic
D ISPL AY
313296J
313296J
To Ram “A”
(1)
(2)
(3)
(4)
BUSS BAR
SHIELDED CABLE
KEY
M
F
(1)
(2)
(3)
(4)
Motor Pigtail
F
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
M
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Ferrite Bead
Cable 8 Pin
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
3
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
Power (1)
Low Sensor (2)
Common (3)
Empty Sensor (4)
Air Solenoid (5)
1
Unused (1)
Drain (2)
Common (3)
Signal (4)
(1) Linear Input
(2) N/C
(3) Motor Reed Up
(4) Motor Reed Down
(5) Motor Reed Com
(6) Linear Power
(7) Linear Com
(8) Drain
5
FLUID
CONTROL
MODULE
RAM “B”
M
(1)
(2)
(3)
(4)
(5)
M
(1)
(2)
(3)
(4)
3
2
Fluid Solenoid
(1)
(2)
F
F
(1)
(2)
(3)
(4)
AIR SOLENOID
(1) Solenoid signal
(2) Solenoid RTN
F
(1) (1) Signal
(2) (2) Common
(3) (GND) Unused
Cable Splitter
Wire Harness
Depress/Recirc Option
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
(1)
(2)
(3)
(4)
(5)
M
3
2
1
Cable Splitter
(1)
(2)
F
(1)
(2)
(3)
(4)
F
(1)
(2)
(3)
(4)
(1) Solenoid signal
(2) Solenoid RTN
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM LOW
AIR SOLENOID
(1) Power
(2) Unused
(3) COM
(4) SIGNAL
DRUM EMPTY
DRUM LOW and EMPTY OPTION
GUN
t
PLATEN
PUMP
HOSE
t
t
t
J-BOX
Cable, CAN
Cable,10AWG
GRN/YEL
Cable, Extension
Cable,10AWG
Black
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
Cable, Extension
Cable, Volex
CABLE TRACK
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
RTD
Input
Heater
Power
SHLD (1)
+24Vdc (2)
-24Vdc (3)
CAN_H (4)
CAN_L (5)
2
3
2
3
2
3
2
3
Line Filter
5
5
5
Heater
Power
DC
Control
5
4
HPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
Heater
Power
LPTCM
8 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
Cable
50A
CONTACTOR
25 Amp
Circuit
Breaker
8 Amp
Circuit
Breaker
Cable
Cable
Cable
Cable
Cable
Cable
Cable
63A
GFCI
Warm Melt Enclosure
D60 Ram B
Schematic
Cable, CAN 15m
Sensor Reed Switch
Top Switch (1)
Top Switch (2)
Bottom Switch (1)
Bottom Switch (2)
M
(1)
(2)
(3)
(4)
(5)
Warm Melt
D60 Ram “B” Option
Electrical Schematics
69
Electrical Schematics
D60 Pump and Platen Schematic
70
313296J
Electrical Schematics
D60 Junction Box Schematic
313296J
71
Electrical Schematics
D60 Cable Harness Schematic
72
313296J
Electrical Schematics
4-Zone Medium Enclosure
Electrical Enclosure
Schematic
313296J
73
Electrical Schematics
4-Zone RAM ‘B’ Enclosure
Electrical Enclosure
Schematic
74
313296J
Electrical Schematics
313296J
75
Parts
Parts
D200s Rams Shown
Supply System B
Single Supply System or Supply System A
5
5
13
14
7
7
15
3
16
3
6
4
2
2
4
76
6
313296J
Parts
NOTE: See Component Identification, starting on
page 8, to identify the components included in your
Warm Melt supply system.
Ref. Part
2❄
3
4
24D066
24D069
24D067
24D070
24D068
24D071
257748
5❄
257749
257750
257623
257624
6❄
7❄
255305
255315
255392
103347
108124
313296J
Description
RAM ASSEMBLY, D60, 3 in.
RAM ASSEMBLY, D60i, 3 in.
RAM ASSEMBLY, D200s, 6.5 in.
RAM ASSEMBLY, D200si, 6.5 in.
RAM ASSEMBLY, D200, 3 in.
RAM ASSEMBLY, D200i, 3 in.
PUMP, Check-Mate; see manual
312375 for parts
PLATEN, 20 liter, double wiper, cst,
polyurethane
PLATEN, 20 liter, double wiper, sst,
polyurethane
PLATEN, 30 liter, double wiper, cst,
polyurethane
PLATEN, 30 liter, double wiper, sst,
polyurethane
PLATEN, 60 liter, double wiper, cst,
polyurethane
PLATEN, 60 liter, double wiper, sst,
polyurethane
PLATEN, 55 gal., PTFE-coated o-ring,
EPDM
PLATEN, 55 gal., o-ring, EPDM
PLATEN, 55 gal., o-ring, neoprene
KIT, mounting, pump; 3 in.; 20 liter; for
NXT 2200 air motors
KIT, mounting, pump; 3 in.; 20 liter; for
NXT 3400 and 6500 air motors
KIT, mounting, pump; 3 in.; 55 gal.
KIT, mounting, pump; 6.5 in.; 55 gal.
KIT, mounting; Check-Mate pump
VALVE, safety relief; located out of
view, on back side of air controls
For systems with pumps: P23xxx or
P36xxx
For systems with pumps: P68xxx
Qty.
1
1
1
1
1
1
1
Ref. Part
13
14
15
24D009
24D010
24D012
24D013
24D015
24D016
1
1
257158
257291
16
1
1
1
1
24D011
24D014
24D017
Description
ENCLOSURE, electrical (see Electrical
Enclosure Parts, page 90)
For single systems and Ram A
For Ram B
KIT, warm melt, with display (see Warm
Melt Kits for D200 Systems, page 78,
or Warm Melt Kits for D60 Systems,
page 83)
D60, Ram, WMxxxx Models
D60, Ram A, TWxxxx Models
D200, 3 in. Ram, WMxxxx Models
D200, 3 in. Ram A, TWxxxx Models
D200, 6.5 in. Ram, WMxxxx Models
D200, 6.5 in. Ram A, TWxxxx Models
KIT, warm melt, with no display (see
Warm Melt Kits for D200 Systems,
page 78, or Warm Melt Kits for D60
Systems, page 83)
D60, Ram B, TWxxxx Models
D200, 3 in. Ram B, TWxxxx Models
D200, 6.5 in. Ram B, TWxxxx Models
Qty.
1
1
1
1
1
1
1
1
1
1
1
❄ See Supply Systems Repair-Parts manual for parts.
1
Stainless Steel Ram Conversion Kits
1
1
1
1
1
1
1
1
For converting carbon steel Ram to stainless steel.
24K670
24K671
24K673
24K675
24K676
24K677
24K678
24K679
24K680
D60, Ram, WMxxxx Models
D60, Ram A, TWxxxx Models
D60, Ram B, TWxxxx Models
D200, 3 in. Ram, WMxxxx Models
D200, 3 in. Ram A, TWxxxx Models
D200, 3 in. Ram B, TWxxxx Models
D200, 6.5 in. Ram, WMxxxx Models
D200, 6.5 in. Ram A, TWxxxx Models
D200, 6.5 in. Ram B, TWxxxx Models
77
Parts
Warm Melt Kits for D200 Systems
Kit 24D012 (CST), 24K675 (SST) with Display for D200 and D200i Systems
Kit 24D015 (CST), 24K678 (SST) with Display for D200s and D200si Systems
Kit 24D013 (CST), 24K676 (SST) with Display for Ram A of Tandem D200 and D200i Systems
Kit 24D014 (CST), 24K677 (SST) without Display for Ram B of Tandem D200 and D200i Systems
Kit 24D016 (CST), 24K679 (SST) with Display for Ram A of Tandem D200s and D200si Systems
Kit 24D017 (CST), 24K680 (SST) without Display for Ram B of Tandem D200s and D200si Systems
Kit 24D016 Shown
11
20
23
12
65
13
26
27
105
22
24
14
60
50
15
21
16
47
71, 72, 73
66
12
11
81
19
32
37
35
18
34
11
12
33
41
36
30
28
76
75
78
17
r_wm_2179_313296_5a
313296J
Parts
42
72, 73
101
78
88
61, 62
83, 84, 85
54
86
11, 12
39
11, 26, 58, 59
52
40
101
80
71
53
TI19984a
313296J
79
Parts
45, 79
46
107(x2), 108(x2), 110
44
51
68, 69, 97, 98
87
103a
103b
57, 99
ti17719a
103c
1
Torque to 60 +/- 10 in-lbs (6.8
+/- 1.1 N•m)
70
49
63
59 1
43
11
107
108
109
64
48
57, 97, 100, 102
46, 56, 82
80
ti17718a
313296J
Parts
59
112
11
90
113
11
93
59
116
101
91
59
11
89
95
94
92
68, 97, 98
117
UBFB
D200 Warm Melt Kits
Ref.
11✓
12
13❖
Part
100016
121112
115827
14❖
15❖
16
15X270
15G347
†277589
◆277591
17
†277590
◆277592
18
†255383
◆15R108
19❖
100696
20✿■ 24F493
21✿✓
22✿✓
23✿✓
24✿
102040
25★
‡123328
26✿
27✿
28
313296J
✖15X968
16C377
110755
121253
114417
Description
Qty.
WASHER, lock
29
SCREW, cap, sch
15
SCREW, cap, hex hd; 7/16-14
1
unc
WASHER, top hat
1
SUPPORT, hose hanger
1
COVER, shroud front
1
- for 3 in. Ram
- for 6.5 in. Ram
COVER, shroud rear
1
- for 3 in. Ram
- for 6.5 in. Ram
1
BRACKET, light tower
1
- for 3 in. Ram
- for 6.5 in. Ram
WASHER, plain
2
MODULE, display
1
BRACKET, pendant pivot
1
BRACKET, mounting, assy
1
SCREW, cap, sch; 1/4-20 unc
1
NUT, lock, hex
1
CABLE, splitter, FCM,
1
empty/air
CABLE, FCM, low/hi/air
1
CABLE, M12, DIN
1
WASHER, plain
5
KNOB, display
1
SCREW, self tap, pan hd
4
Ref.
29★
30
Part
121070
31★
121001
121228
32❖
101213
33
289697
34*‡✖ 122716
35*‡✖
36■
289696
37*‡✖
39
†❋
◆✠
40
†❋
◆✠
277674
257163
41❖
42✓
43●
44✛✓★ 121980
45✛★ 16J890
46●✛✓ 16D383
✖
47❖
119832
48●✓ 15V427
Description
Qty.
SUPPRESSOR, ferrite bead
1
SCREW, machine; #8-32 x 1
1
3/8
CABLE, CAN, female/female;
1
0.5 m
Kits 24D014 and 24D017 only
NUT, full, hex
MODULE, cube, base
SENSOR, inductive, M12
BRACKET, sensor, low/empty
MODULE, fluid control
ACTUATOR, sensor,
low/empty
BRACKET, mounting, bottom
- for 3 in. Ram
- for 6.5 in. Ram
BRACKET, mounting
- for 3 in. Ram
- for 6.5 in. Ram
ENCLOSURE, cube door
CABLE, track
CONDUCTOR, block, heater
HEATER, pump, 725 watt
SUPPORT, sensor
SENSOR, RTD, shielded
BOLT, eye, 3/8-14 x 6
HEATER, coil
1
1
1
1
1
1
1
1
1
1
2
2
1
2
1
2
81
Parts
Ref.
Part
49◗●✓✖
50
†❋
◆✠
51✛✓ ★ 15W706
52✛✓ ★ 15W707
53
54
56
117026
57✓★ 116343
58
100014
100058
59✓
100015
60❖
100133
61
C19837
62●
63◗●
64
65❖
66❖
67
68
69
70◗●
71
72
73
74
75
76
78
79
80
81❖
82
83❂
84❂
176692
100307
C34132
15Y051
123507
16H441
120223
100020
100179
111218
121255
16M941
C31012
110637
119958
110170
85❂
86▲
87▲
89✓
90
91
92✓
24B810
93
94
95
97
98
99✓
100✓✖
101▲
102✓✖
113970
C19208
102794
111640
100166
16A355
16A356
196548
16A574
82
15J075
15H668
Description
Qty.
COVER, platen front, assy.
2
BRACKET, mounting, top
1
- 3 in. Ram
- 6.5 in. Ram
ENCLOSURE, pump, front
1
ENCLOSURE, pump, rear
1
CONDUIT; 12.9 mm
4
COUPLER, conduit
4
SCREW, shcs; m5 x 12
1
SCREW, ground
2
SCREW, cap, hex hd
4
- for 3 in. ram
- for 6.5 in. ram
NUT, hex mscr
12
WASHER, flat
2
SCREW, cap, hex hd
2
STUD, 3/8-16 x 1.25
6
PLUG, finishing; 13/16 in.,
1
nickel plated
WASHER, flat
6
NUT, hex
2
HANGER
1
CABLE, M12
1
WIRE, grounding
1
WIRE, grounding
1
FASTENER, platen, cover
2
SCREW, machine, flat hd
4
WASHER, lock
4
NUT, hex mscr
4
CAP, tube
1
COVER
1
SCREW, countersunk; 6-32 x
2
0.38
BRACKET, cable and rack
1
CLAMP
1
SCREW, machine, pan hd
4
SPRING, hose hanger
1
WASHER
1
O-RING
1
CONNECTOR, power, female,
1
3 pin
COVER, connector
1
LABEL, warning
2
LABEL, warning
1
RAIL, din, assy.
1
BUSHING, strain relief; m40
1
NUT, strain relief; m40
1
CONNECTOR, bulkhead; 15
1
pin
SCREW, socket hd cap
4
WASHER, lock
4
NUT, hex
4
WASHER, lock
6
NUT, full hex
5
WIRE, ground, pump
1
WIRE, ground, platen
1
LABEL, caution
1
WIRE, ground
4
Ref.
103
Part
255392
103a
103b
103c
104★
106★
107
108
109✓ ★
110✓ ★
111★
112
113
114
115
116
117
102637
276025
109495
15Y051
124131
103187
15B137
16K094
114958
16A539
16A543
299653
C33037
112788
16A541
Description
Qty.
KIT, mounting, displacement
1
pump
SCREW, cap
4
CLAMP
4
O-RING
1
STUD
6
CABLE
1
SCREW
4
WASHER, lock
4
SWITCH, thermal
1
SWITCH, overtemp, horizontal
1
STRAP TIE
7
JUNCTION BOX
1
BRACKET
1
SHRINK TUBE
1
TAPE, fiberglass
1
SCREW
4
COVER, junction box
1
★ Not shown.
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost.
† Kit 24D012 only.
◆ Kit 24D015 only.
✿ Kits 24D013 and 24D016 only in tandem supply systems.
❖ Parts included in Hose Hanger Kit 234966 (purchase
separately).
‡ Parts included in Low or Empty Sensor Kit 255469 (purchase separately).
✖ Parts included in Drum Low and Empty Sensor Kit
24C530 (purchase separately).
❋ Parts included in 3 in. Ram Bracket Mounting Kit
24C628 (purchase separately).
✠ Parts included in 6.5 in. Ram Bracket Mounting Kit
24C660 (purchase separately).
● Parts included in Platen Heater Kit 24C493 (purchase
separately).
✛ Parts included in Pump Heater Kit 24C495 (purchase
separately).
◗
Parts included in Platen Cover Kit 255691 (purchase
separately).
✓ Parts only available in Display Mounting Kit 24C653
(purchase separately).
❂ Parts only available in Cover Connector Kit 256883
(purchase separately).
■ Replacement electronic components do not have Warm
Melt specific software installed. Therefore, use software
upgrade token 16C027 to install software before use.
313296J
Parts
Warm Melt Kits for D60 Systems
Kit 24D009 (CST), 24K670 (SST) with Display for D60 and D60i Systems
Kit 24D010 (CST), 24K671 (SST) with Display for Ram A of Tandem D60 and D60i Systems
Kit 24D011 (CST), 24K673 (SST) without Display for Ram B of Tandem D60 and D60i Systems
Kit 24D010 Shown
209
202
210
201
203
207
202
201
211
279
213
280
208
204
206
214
201
202
281
219
215
224
217
220
205
254
253
r_wm29yy_31329b6_5
313296J
83
Parts
258
233
259,
260,
261
237
257
236
r_wm_2179_313296_12a
84
235
313296J
Parts
227
256
249, 272,
273
282, 283, 284
228,
229
234
227
239,
274
262
ti17721a
201, 202
232
223
201, 213, 240, 241
201, 202, 222
313296J
85
Parts
241
255
201
265
258
201
268
241
278
276
266
241
201
264
213✿✓
214✿✓
215
216★
217
218★
219
220■
222❋
223❋
86
110755
121253
114417
123375
121070
121001
289697
289696
267
UBFB
D60 Warm Melt Kits
15X968
269
248, 272, 273
271
Ref.
Part
201
100016
202
121112
203
288543
204
277589
205
277590
206
255383
207✿■ 24F493
208✿✓
209✿✓
210✿✓
211✿✓ 102040
212★
16C377
270
Description
WASHER, lock
SCREW, cap, sch
BRACKET, hose spring
COVER, shroud front
COVER, shroud rear
BRACKET, light tower
MODULE, display
BRACKET, pendant pivot
BRACKET, mounting, assy
SCREW, shcs; 1/4 unc x 4.25
NUT, lock, hex
CABLE, M12;
Kits 24D009/24K670 only
CABLE, splitter, FCM empty/air;
Kits 24D010. 24D011, 24K671,
24K673 only
WASHER, plain
KNOB, display
SCREW, self tap, pan hd
SUPPRESSOR, ferrite bead
SCREW, machine; #8-32 x 1 3/8
CABLE, CAN, female / female; 1m
MODULE, base
MODULE, fluid control
BRACKET, mounting, bottom
BRACKET, mounting
Qty.
31
23
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
Ref.
224
225★
227✛
228✛
229✛
232❋
Part
277674
16C430
121980
16J890
16D383
233✛
◆
234✛
◆
235
236
239
240
241
247★
248
249
250
253
254
255✛
256
257
258
259❂
260❂
15W706
16K771
15W707
16K772
116343
100014
100015
15Y051
123507
16A574
16H441
121255
16A539
C31012
110637
Description
Qty.
ENCLOSURE, cube door
1
HARNESS
1
HEATER, pump; 725 watt
2
SUPPORT, sensor
1
SENSOR, RTD, shielded
1
BRACKET, mounting,
1
accessory box
ENCLOSURE, pump, front
1
ENCLOSURE, pump, front, SST
ENCLOSURE, pump, rear
1
ENCLOSURE, pump, rear SST
CONDUIT; 12.9 mm
2 ft
COUPLER, conduit
3
SCREW, ground
1
SCREW, cap, hex hd
4
NUT, hex mscr
8
CABLE, M12, 8 pin, f/m
1
WIRE, grounding, panel
1
WIRE, grounding, door
2
WIRE, grounding
1
COVER
1
SCREW, countersunk, 6-32 x 0.38
2
BOX, junction box
1
CLAMP
1
SCREW, mach, pan head
4
BRACKET, mount
1
O-RING
1
CONNECTOR, power,
1
female, 3 pin
313296J
Parts
Ref.
Part
261❂
262▲ 15J075
263★▲ 15H668
264
265
266
267
24B810
268
113970
269
C19208
270
102794
271
272
111640
273
100166
274
16A355
276▲ 196548
277★ 114958
278
112788
279*‡✖
280*‡✖ 122716
281*‡✖
282
124131
283
103181
284
16K094
285
C33037
286
106245
287
157974
288
16K066
313296J
Description
COVER, connector
LABEL, warning
LABEL, warning
RAIL, din, assy
BUSHING, strain relief; M40
thread
NUT, strain relief; M40 thread
CONNECTOR, bulkhead, 15 pin
SCREW, cap, sch
WASHER, lock
NUT, hex
COVER, junction box
WASHER, lock, internal
NUT, full hex
WIRE, ground
LABEL, caution
STRAP, tie
SCREW, cap, sch
BRACKET, sensor, low/empty
SENSOR, inductive, M12
ACTUATOR, sensor, low/empty
SCREW
WASHER, lock
SWITCH, overtemp, horizontal
TAPE, fiberglass
SCREW
WASHER
CLAMP, support
Qty.
1
1
1
1
1
1
1
4
4
4
1
4
4
1
1
7
4
1
2
1
2
2
1
1
1
1
1
★ Not shown.
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost.
*
Standard only on tandem supply systems.
✿ Kits 24D009, 24D010, 24K670, and 24K671.
‡ Parts included in Low or Empty Sensor Kit 255469
(purchase separately).
✖ Parts included in Drum Low and Empty Sensor Kit
24C530 (purchase separately).
❋ Parts included in 3 in. Ram Bracket Mounting Kit
24C628 (purchase separately).
✛ Parts included in Pump Heater Kit 24C495 (purchase
separately).
◆ Parts included in Stainless Steel Pump Heater Kit
24K669 (purchase separately).
✓ Parts only available in Display Mounting Kit 24C653
(purchase separately).
❂ Parts only available in Cover Connector Kit 256883
(purchase separately).
■ Replacement electronic components do not have
Warm Melt specific software installed. Therefore,
use software upgrade token 16C027 to install software before use.
87
Parts
Heated Platens - 20L, 30L, and 60L
Platen 24D066 (20L) Shown
327
335
325, 326
309 1 3
324
323
3 311
320
319
318
4 322
317
301
321
308 3
333
309 1
334
336
3
307
328, 329, 330
313 2
303
ti17717b
304, 305
310
302
1 Torque to 45 +/- 5 in-lbs (5.1 +/- 0.6 N•m)
2 Apply sealant to all non-swiveling pipe threads.
3 Add lubricant to threads.
4 Ground RTD sleeve to screw (332).
88
313296J
Parts
Parts Used on all Heated Platens
Ref.
301
305
306
309
311
312
313
317
318
319
Part
121829
257697
109482
C20350
320
321
Description
Qty.
BASE, platen
1
PLATE, bottom
1
O-RING
1
NUT, keps, hex hd
12 or 20
HANDLE, bleed, sst, assy
1
O-RING
1
ELBOW, 90 deg.
1
GASKET, heat transfer
1
PLATE, heater, lower
1
HEATER (includes wiring to
1
switch 336)
PLATE, heater, upper
1
HOLDER, RTD sensor
1
Ref.
322
323
324
325
326
327
328
329
330
331
332
335
336
337
338
Part
Description
16D383 SENSOR, RTD, 1k ohm,
shielded
NUT, barrel, binding screw
GUARD, heat shield
COUPLER, conduit
CONDUIT, ID 12.9mm
189930 LABEL, caution
C38163 WASHER, lock, external
100166 NUT, full hex
16A356 WIRE, ground
16H441 WIRE, ground
111593 SCREW, grounding
15K616 LABEL, safety
15B137 SWITCH, thermal
104714 SCREW, machine
103181 WASHER, lock
Qty.
1
4
1
1
36
1
1
1
1
1
1
1
1
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost.
Parts that Vary by Heated Platen Model
Heated Platen Models
Qty
24D066, 20L
Platen, CS
24D067, 30L
Platen, CS
24D068, 60L
Platen, CS
24D069, 20L
Platen, SST
24D070, 30L
Platen, SST
24D071, 60L
Platen, SST
302 SPACER, dual wiper
257694
257695
257696
262873
262874
257684
1
303 WIPER, main
257678
257679
257680
257675
257676
257677
2
304 WIPER, support
257681
257682
257683
257681
257682
257683
1
307 PLATE, top
257686
257687
257688
257698
257699
257725
1
308 SCREW, set, sch
100421
100421
100421
109477
109477
109477
2
310 VALVE, check
122056
122056
122056
501867
501867
501867
1
333 WIPER, support
---
---
---
15V442
15V443
15V444
1
334 SPACER, nylon, 3/4 in.
---
---
---
16J835
16J835
16J835
1
Ref. Description
313296J
89
Parts
Electrical Enclosure Parts
257158 for single supply systems and ram A of tandem supply systems
257291 for ram B of tandem supply systems
Side View
257158 Shown
443, 458
440
441
439
401
451
436
437
439
439
442
438
439
433, 434, 435
452
445
407
444
402, 403, 404, 405
427
457
459
415, 426
406
461
425, 453
415
456
416
417
420
415
426
466
429
408, 409, 410
430
414
412
318
460
422
413
417
415, 426
421
423
411
432
90
419
428
431
424
313296J
Parts
Electrical Enclosure Parts
Ref.
Part
401
402
403
101682
404
100016
405
100015
406
15X754
407★ 289697
408■★ 256270
409
114417
410
121070
411■★ 255774
412
15U651
413
15R535
414
415
416★
417★
117831
100035
122148
122619
418
419★
420★
421★
422
423★
424★
425
426
427★
428
122129
122128
16A573
122122
122317
122125
123141
111640
157021
429★
430★
431★
432★
433
434
435
436
121597
15V999
437
438
439
440
441
442★
443
444
445
451
452
453
454
456
457
257341
121000
100023
100133
100307
121612
112788
15W905
16H441
100166
123507
277674
186620
313296J
Qty
Description
.
ENCLOSURE
1
DOOR, enclosure
1
SCREW, cap, sch
4
WASHER, lock
4
NUT, hex, mscr
4
BRACKET, mounting, electrical
1
MODULE, cube, base
3
MODULE, low power temp
3
SCREW, self tap, pan hd
12
SCREW, machine, pan hd
3
MODULE, high power temp
1
BRACKET, high power temp mod1
ule
BRACKET, mounting, high power
1
temp module
SCREW, machine, pan hd
4
SCREW, machine, pan hd
20
BAR, buss, smissline; 17.125 in.
1
CIRCUIT, breaker, smissline; 10A
4
(257291 includes qty. of 3)
COVER, buss bar
1
CIRCUIT, breaker
1
WIRE, power
2
SWITCH, disconnect
1
ROD, connecting, on/off
1
RELAY, contactor
1
CIRCUIT, breaker, smissline; 25A
1
WASHER, lock, internal
2
WASHER, lock, internal
10
KIT, bar, ground
1
HARNESS, wiring, high power
1
temp module
CABLE, CAN, 90 female/90 female
2
CABLE; 14 in.
3
CABLE; M8, male/ferrules
1
CABLE, CAN, female/female; 0.5 m 1
WASHER, flat
4
WASHER, lock
4
NUT, hex
4
PANEL, side, 3 low power heat
1
modules, 1 hp
GASKET, low power heat module
3
GASKET, high power heat module
1
LABEL, junction box
1
CORD, grip; PG-7
1
GRIP, cord
1
CONNECTOR, thru; M12, m x f
1
SCREW, cap, socket hd
6
LATCH, quarter turn
2
HANDLE, selector, on/off
1
SEAL, hole, plug; 0.5 in.
1
WIRE, grounding, door
1
NUT, full hex
2
WIRE, ground
1
ENCLOSURE, cube door
3
LABEL, ground
1
Ref.
458
459★
460★
461
466
467
Part
112905
123373
123374
Description
WASHER, plain
FILTER, power line; single phase
SUPPLY, power; 24Vdc, 2.5A,
60W
(included in only 257158)
COVER, buss bar, single
125789 CABLE, CAN, female/female
123615 TERMINAL, bus bar, L3 (257291
only)
Qty
.
6
1
1
1
1
1
★ Not shown.
▲ Replacement Danger and Warning labels, tags, and
cards are available at no cost.
■ Replacement electronic components do not have
Warm Melt specific software installed. Therefore,
use software upgrade token 16C027 to install software before use.
91
Accessories
Accessories
Platen Cover, 255691
Two platen covers. See manual 406681 for more information for D200 platens.
Two-Zone Expansion Kit, 24C223
For adding two zones of heat to a Warm Melt Supply
System. The two extra zones are controlled through the
Warm Melt display.
Two-Zone Accessory Kit, 24C222
Controls two zones of heat; up to 212°F (100°C).
Four-Zone Accessory Kit, 24C526
Controls four zones of heat; up to 212°F (100°C).
Light Tower Accessory Kit, 255468
For use with Warm Melt or Tandem Supply Systems.
Low and Empty Sensor Kit, 24C530
Indicates when the drum is low and empty. Includes two
sensors: one to be used as a low sensor, and one to be
used as an empty sensor. For use with Warm Melt (to
add a low sensor), Ambient, and Tandem supply systems.
92
313296J
Appendix A - User Interface Display
Appendix A - User Interface Display
Display Overview
Display Details
The user interface display is divided into two main functions: Setup mode and Run mode.
Power Up Screen
Setup Mode Functions
The setup mode functions enable users to:
•
•
•
•
•
•
•
•
The following screen appears when the display module
is powered up. It remains on while the display module
runs through initialization and establishes communication with other components in the system.
set and change the password;
configure system parameters;
set heat zone parameters;
schedule maintenance parameters;
configure system hardware settings;
set and change display units and format for all
other screens;
set pump size and drum fill volume;
and view software information for each system
component.
Run Mode Functions
The run mode functions enable users to:
•
•
•
•
•
•
•
view current flow rate and drum volume;
view temperature for heat zones;
view system job totals and grand totals, and
reset totals;
view current pressures;
view and reset maintenance counters;
view and clear individual alarms;
and view the alarm log.
FIG. 59: Power Up Screen
Menu Bar
The menu bar appears at the top of the screen, and
consists of the following components.
FIG. 60: Menu Bar
Date and Time
The date and time are always displayed in one of the following formats. The time is always displayed as a
24-hour clock.
•
DD/MM/YY HH:MM
•
MM/DD/YY HH:MM
Navigation
The navigation section, which is to the right of the date
and time, indicates the active screen with the center,
highlighted icon. The left and right arrows indicate there
are more screens that can be accessed within a mode.
313296J
93
Appendix A - User Interface Display
Navigation within Screens
Status
The current system status is displayed on the right of
the menu bar. If there is an error, an event icon and
either a text description of the event or the standard
error code for the event is displayed. If there are no
errors or deviations, nothing is displayed.
Press
to open drop-down menus on Setup
screens. Also, press
to enter changes or make a
selection.
Mode
The mode section displays the current system mode.
The current mode is highlighted.
Press
Error
to navigate to new screens and to
navigate left and right within a screen. Also press
The current system error is displayed in the menu bar.
There are four possibilities:
Icon
Function
No Icon
No information or no error has occurred
Advisory
select digits within a field to change.
Press
to navigate to new screens and to
navigate up and down within a screen. Also press
to move between fields within a drop-down
Deviation
menu, and to increment or decrement numbers within a
field.
Alarm
Soft Keys
Icons above the soft keys indicate which mode or action
is associated with each soft key. Soft keys that do not
have an icon above them are not active in the current
screen.
Jump In/Jump Out
In screens that have editable fields, press
to
access the fields and make changes. When changes
are complete press
94
to exit edit mode.
313296J
Appendix A - User Interface Display
Setup Mode Screens
Setup mode screens are divided into six sections: password, system setup, heat zone setup, maintenance
setup, hardware setup, and advanced setup.
System Setup
The System Setup screen enables users to configure
system settings for the ram(s). Press
to access the
Password Screen
fields and make changes. Press
While in Run mode, press the Setup
button. If the
password is not set to 0000, the Password screen will
appear. Enter the password to continue to Setup mode.
NOTE: Upon the first system startup, the System
Setup screen will display. Otherwise, the last setup
screen viewed will display.
Icon
Function
Select tandem operation, ram A only operation, or ram B only operation.
Select if a Not Primed event will issue an
alarm or deviation.
Set number of minutes (1-9) for priming.
Set Password
To set the password, press
Press
to exit edit mode.
to enter the screen.
to select digit to change. Press
Set pump cycles per minute that will issue
a pump runaway alarm. Set between 0 and
99; default setting is 60 cycles; 00 setting
disables this function.
to set value for each digit. Press
again to enter the password.
FIG. 62: System Setup
FIG. 61: Password Screen
Heater System Setup Screen
This screen enables users to set parameters for each
heat zone. Press
to scroll through each
heat zone. When the desired heat zone displays, press
to access the fields to make changes. Press
to exit edit mode.
313296J
95
Appendix A - User Interface Display
NOTE: Must exit edit mode to scroll through the
heat zones.
Icon
Function
Maintenance Setup Screen
The Maintenance Setup screen enables users to set
maintenance intervals for rebuilding platen seals and
rebuilding the pump.
Displays selected heat zone. Press
to scroll through each heat
zone.
Set the temperature setpoint for each heat
zone.
Set the number of degrees the setpoint will
be decreased by when the heat zone is in
setback mode.
Set the number of degrees the heat zone
can go above the setpoint before an alarm
is issued.
Set the number of degrees the heat zone
can go above the setpoint before a deviation is issued.
Select to enable the heat zone; leave blank
to disable the heat zone.
Icon
Function
Set the number of drums (0-9999) between
platen seal maintenance. Setting the number of pump cycles to 0 disables this function. If using a tandem system, set for each
ram. A rebuild platen seals error is issued
when maintenance is required. See Alarm
Codes and Troubleshooting on page 36.
Set the number of pump cycles (0-9999)
between pump maintenance. Setting the
number of pump cycles to 0 disables this
function. If using a tandem system, set for
each pump. A rebuild pump error is issued
when maintenance is required. See Alarm
Codes and Troubleshooting on page 36.
Shared zone. Select to enable zone for
both ram A and ram B.
FIG. 64: Maintenance Setup
FIG. 63: Heater System Setup Screen
96
313296J
Appendix A - User Interface Display
Hardware Setup Screens
The Hardware Setup screens enable users to specify if
specific hardware is installed on the system and to
adjust hardware settings. Press
Monitor the filter pressure readings through the normal
range of flow with a clean filter to establish the initial limit
settings.
to scroll
through the Hardware Setup screens. Once in the
desired Hardware Setup screen, press
the fields to make changes. Press
to access
to exit edit
mode.
NOTE: Must exit edit mode to scroll through the
Hardware Setup screens.
FIG. 65: Hardware Setup Screen 1 (Filter)
Hardware Setup Screen 1
This screen enables users to specify if a fluid filter monitor is installed, and set the high and low limits for the
pressure drop across the filter.
Icon
Function
Select what type of error will be issued if filter pressure drops below the low limit or
raises above the high limit. Select
to
disable filter monitoring or if there is no filter installed on the system.
Set low limit (0-1000 psi) for pressure drop
that will issue an error. Set the low limit to
detect a filter element collapse or a missing
element.
Set high limit (0-5000 psi) for pressure drop
that will issue an error. Set the high limit to
detect a clogged filter.
Hardware Setup Screen 2
This screen enables users to specify if a fluid solenoid is
installed, and if a drum low sensor is installed. The fluid
solenoid controls the depressurize/recirculate valve.
Icon
Function
Select if fluid solenoid is installed on system. Set for A and B rams.
Select if drum low sensor is installed on
system. Set for A and B rams.
FIG. 66: Hardware Setup Screen 2
313296J
97
Appendix A - User Interface Display
Advanced Setup Screens
The Advanced Setup screens enable users to set units,
adjust values, set formats, and view software information for each component. Press
to scroll
through the Advanced Setup screens. Once in the
desired Advanced Setup screen, press
the fields to make changes. Press
to exit edit
NOTE: Must exit edit mode to scroll through the
Advanced Setup screens.
Advanced Setup Screen 1
This screen enables users to set units that display on
other screens.
NOTE: On two-zone and four-zone enclosure acces-
Icon
and
This screen enables users to set the pump size (in
cc/cycle) and the drum fill volume (in volume units). The
drum fill volume is the amount of material in a new drum,
which is used to calculate the volume of material
remaining during operation.
to access
mode.
sory kit, only
Advanced Setup Screen 2
settings are available.
NOTE: These values must be entered accurately for
the volume remaining estimates on the Ram Operation screen to be accurate.
Icon
Function
Set pump size (cc/cycle) for each ram.
Check-Mate: Select between 60, 100,
200, 250, and 500.
Dura-Flo: Select between 145, 180,
220, 290, 430, 580, and 1000.
Set fill volume for each drum. Use digits 1-9999.
Change between a Check-Mate or
Dura-Flo pump.
Function
Select units of measurement for volume.
Select between cycles/gal. gal., oz., and
liters/cc.
Set units of measurement for maintenance
intervals. Select between cycles, drums,
gal., and liters.
Set units of measurement for pressure.
Select between psi and bar.
Set the password. Use digits 0-9999;
0000 = no password.
Set units of measurement for temperature.
Select between °F and °C.
FIG. 68: Advanced Setup Screen 2
FIG. 67: Advanced Setup Screen 1
98
313296J
Appendix A - User Interface Display
Advanced Setup Screen 3
Advanced Setup Screens 4 and 5
This screen enables users to set the date, time, and
date format.
These screens display the software part number and
version information for the system components. Only
system components that are detected via the system
data bus will be displayed on these screens.
Icon
Function
Set date format. Select between
MM-DD-YYYY and DD-MM-YYYY.
Set current date.
Set current time.
Icon
Function
Controller software part number and version.
Display software part number and version.
Fieldbus gateway software part number
and version.
Temperature controller software part number and version.
FIG. 69: Advanced Setup Screen 3
FIG. 70: Advanced Setup Screens 4 and 5
313296J
99
Appendix A - User Interface Display
Run Mode Screens
Run mode screens are divided into six sections: ram
operation, heat zone operation, current system status,
preventative maintenance schedule, current alarms, and
error reports. The system starts in Run mode. If the system is in Setup mode, press
See Operation, page 28, for instructions on all of these
procedures.
Active ram is
highlighted
to enter Run mode.
Flow
rate
Fluid line shown filled when
system is Run Mode
Ram Operation Screen
The Ram Operation screen displays which ram (A or B)
is active, and how much volume remains in each drum.
This screen also displays the flow rate of the active ram.
When the fluid line is shown filled the system is on.
Volume
Remain
Depending on the current system status, users can perform the following procedures from the Ram Operation
screen:
Current
mode
•
•
•
•
•
100
turn the air motor on and off;
depressurize and pressurize the system;
recirculate fluid within the active ram;
prime the pump(s);
and perform a manual crossover on tandem systems.
FIG. 71: Ram Operation Screen - Tandem System
The Ram Operation screen will display the appropriate
icon and highlight the corresponding soft key if the system is:
•
depressurized
,
•
in Recirculate mode
•
or if a ram is in Prime mode
,
.
313296J
Appendix A - User Interface Display
Heat Run Screen
The Heat Run screen displays information for four to six
heat zones. See FIG. 72 for information about each
zone. For each zone, the icon on the upper right is present if the zone is enabled, otherwise the space is blank.
The temperature unit is shown in the upper right of the
menu bar. An alarm icon displays in the bottom right if
there is an alarm or deviation on a heat zone. Press the
soft key under the alarm icon to clear the alarm or deviation.
NOTE: Heat zones five and six are located in the
two-zone expansion kit.
From the Heat Run screen, users can view heat zone
information for each ram, put heat zones into Setback
mode, turn heaters on and off for enabled heat zones,
and change the individual zone temperature settings.
View Heat Zone Information
To view heat zone information, press
scroll through the Heat Run screens.
NOTE: Must exit edit mode to scroll through the
Heat Run screens.
Heat zones seven through ten are located on Ram B.
Heat zones eleven and twelve are located in the
two-zone expansion kit.
Setback Mode
The last digit in the temperature control module alarm
codes represents the zone reporting the alarm.
zones, press
Zone
Number
Temperature Control
Module Alarm Code
A1
A2
A3
A4
A5
A6
B1
B2
B3
B4
B5
B6
1
2
3
4
5
6
7
8
9
10
11
12
To put heaters into setback mode for enabled heat
. The setpoint for each zone will be
decreased by the setback amount set on Heater System Setup Screen, page 95.
Turn On Heaters
See System Heat Up, page 26, for instructions.
Change Zone Temperature Setting
Press
to access the fields to make changes. Use
the navigation buttons to move to the desired heat zone.
Enter the new temperature and press
change. Press
System component
being heated
Zone
number
to
to save the
to exit edit mode.
Zone set point
Current zone temperature
FIG. 72: Heat Run Screen - Ram A
313296J
101
Appendix A - User Interface Display
Status Screen
Maintenance Screen
This screen displays the job totals and grand totals. If
there is a filter or an error issued, there will be a second
The maintenance screen enables operators to establish
a preventive maintenance schedule based on the system application and repair history. This screen displays
the number of maintenance units remaining before preventive maintenance is due for the platen seals and
pump.
screen. Press
to scroll to through the
Status screens.
Icon
Function
Job total column; indicates pump cycle
count total for a single job.
NOTE: If a maintenance interval is set to 0, the display will be a series of dashes.
Icon
Grand total column; indicates pump cycle
count total for all jobs.
Function
Current count remaining until platen
requires maintenance.
Platen maintenance is reported in
Displays pump cycle count for Ram A for
a single job and all jobs.
drums
Displays pump cycle count for Ram B for
a single job and all jobs.
.
Current count remaining until pump
requires maintenance.
Pump maintenance is reported in units
Displays pump cycle count for entire system for a single job and all jobs.
set by the maintenance unit control
in the Advanced Setup screen 1. The
example shown in FIG. 74 is set to units of
1000 pump cycles
.
FIG. 73: Status Screen 1
To reset a job total for a single ram (A or B), press
FIG. 74: Maintenance Screen
to access the fields, navigate to the value, and press
. When prompted, press
to confirm. If the job
total is reset, A and B totals will also be reset. Press
to exit edit mode.
To reset a counter, press
to access the fields, nav-
igate to the value, and press
. When prompted,
press
to exit edit mode.
to confirm. Press
NOTE: Grand totals cannot be reset.
102
313296J
Appendix A - User Interface Display
Alarm Screen
Report Screens
The alarm screens display the type of alarm currently
occurring on each ram. Once an alarm is resolved, use
this screen to clear the alarm.
The five Report screens display a chronological list of
the most recent 20 errors. See Alarm Codes and Troubleshooting, page 36, for details regarding each alarm
code.
NOTE: For more information regarding alarms. See
Alarms on page 36.
Icon
Alarm
Code
B61X
B62X
DA1X
DA2X
DB1X
DB2X
DK1X
KD2X
DD1X
DD2X
L11X
L12X
Icon
Function
Chronological order of errors as they
occur.
Function
Crossover Error
A crossover to a pump with an
error was attempted.
Pump Runaway
Pump is running faster than the
runaway limit.
Pump Not Primed
A new drum has not been
primed.
Air Motor Sensor Error
Air motor sensor detects a fault
in the pump motion.
Pump Diving
Pump leak or ram air pressure is
too low.
Date when error occurred.
Time when error occurred.
Error code.
Press
to scroll through the five report
screens.
Drum Empty
Drum for ram A or ram B is
empty.
FIG. 76: Report Screen
FIG. 75: Ram Alarm Screen
To clear an alarm, press
to access the fields, navi-
gate to the alarm icon, and press
prompted, press
. When
to confirm. Press
to exit edit
mode.
313296J
103
Dimensions
Dimensions
D200 Models
D200s Shown
G
B
(ram down)
A
(ram up)
C
D
E
F
Ram
Model
A
in. (mm)
B
in. (mm)
C
in. (mm)
D
in. (mm)
E
in. (mm)
F
in. (mm)
G
in. (mm)
D200
102.3 (2599)
72.6 (1844)
21.0 (533)
25.0 (635)
38.0 (965)
42.0 (1067)
56.4 (1433)
D200s
104.9 (2665)
74.3 (1887)
23.0 (584)
25.0 (635)
45.0 (1143)
48.0 (1219)
64.6 (1641)
104
313296J
Dimensions
D60 Models
G
B
(ram down)
A
(ram up)
C
D
E
F
Ram
Model
A
in. (mm)
B
in. (mm)
C
in. (mm)
D
in. (mm)
E
in. (mm)
F
in. (mm)
G
in. (mm)
D60
92.7 (2355)
62.7 (1593)
14.0 (356)
18.0 (457)
24.0 (610)
28.0 (711)
47.0 (1194)
313296J
105
Technical Data
Technical Data
Max air input pressure (supply system)
D60 - 3 in. dual post, 5 gal. (20 L), 16 gal. (60 L),
30 gal. (115 L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D200 - 3 in. dual post, 55 gal. (200 L) . . . . . . . . . . . .
D200s - 6.5 in. dual post, 55 gal. (200 L). . . . . . . . . .
Max fluid and air working pressure . . . . . . . . . . . . . . . . .
Wetted parts and weight (displacement pump) . . . . . . . .
Platen Codes (see page 4): Part number; Wetted parts
F: 257729, 5 gal. (20 L)
L: 257734, 8 gal. (30 L)
U: 257738, 16 gal. (60 L). . . . . . . . . . . . . . . . . . . . . .
H: 257731, 5 gal. (20 L)
R: 257736, 8 gal. (30 L)
Y: 257741, 16 gal. (60 L) . . . . . . . . . . . . . . . . . . . . . .
8: 255662, 55 gal. (200 L) . . . . . . . . . . . . . . . . . . . . .
9: 255663, 55 gal. (200 L) . . . . . . . . . . . . . . . . . . . . .
Maximum operating temperature (supply system)
Sound data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External power supply requirements
AC power units . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
150 psi (1.0 MPa, 10 bar)
150 psi (1.0 MPa, 10 bar)
125 psi (0.9 MPa, 9 bar)
See table below.
See Check-Mate Displacement Pump manual 312375.
Stainless steel, polyurethane, PTFE coated nitrile, polyethylene, nitrile, PTFE, 303 sst, 304 sst, 316 sst,
17-4PH sst
Electroless nickel, aramind reinforced elastomer, rubber-based PSA, polyurethane, polyethylene, nitrile, zinc
plated carbon steel, buna, 1018 carbon steel, 304 sst,
316 sst, 17-4PH sst
PTFE, EPDM, PTFE coated aluminum, zinc plated
carbon steel, 316 sst
EPDM, aluminum, zinc plated
carbon steel, 316 sst
158°F (70°C)
See NXT Air Motor manual 311238.
220-250 Vac, 50/60 Hz, single phase, 57 amps full load
current
Maximum Fluid Working Pressure and Flow Rate at Full Air Pressure (100 psi)
Maximum Air Inlet
Maximum Fluid Working
Ratio Pressure psi (MPa, bar) Pressure psi (MPa, bar)
Motor
Displacement
Pump
(cc per cycle)
Flow Rate gpm (lpm)
30 cpm
60 cpm
23
100 (0.7, 7.0)
2300 (16.1, 161)
NXT2200
200
1.6 (6.0)
3.2 (12.0)
36
100 (0.7, 7.0)
3600 (25.2, 252)
NXT3400
200
1.6 (6.0)
3.2 (12.0)
68
91 (0.64, 6.4)
6200 (43.4, 434)
NXT6500
200
1.6 (6.0)
3.2 (12.0)
Weight
See the identification plate (ID) for the weight of your
supply system.
ID
ti11157a
106
313296J
Technical Data
313296J
107
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 313296
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised January 2015

advertisement

Related manuals

advertisement