A-Neu Video HD-88K Instruction manual
A-Neu Video HD-88K is an 8x8 matrix routing switch that supports 8 HDMI inputs and 8 HDMI outputs. It supports full resolution HDMI video with embedded HDCP and a signal bandwidth of 340Mhz, so there is no signal degradation. High definition digital signals can be selected and distributed to any of the 8 inputs to 8 outputs. This switcher is certified as being fully CEC, ARC and HDCP 1.3 compliant, with full HD 4K2K HDMI V1.4a 3D formats and data rates up to 6.75Gbps. Supports UXGA/WUXGA/DVI 1920x1200 resolutions to any HD display.
Advertisement
Advertisement
HD-88K
8x8 UHD 4K2K HDMI MATRIX SWITCH
A-NeuVideo.com
Frisco, Texas 75034
(469) 277-7606
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the
HDMI Locking Post replacement screws will void your warranty.
AUDIO / VIDEO MANUFACTURER
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
A NEU VIDEO
TABLE OF CONTENTS
CONTENTS
PACKAGE CONTENTS ................................................................1
INTRODUCTION & FEATURES ....................................................2
SPECIFICATIONS ........................................................................3
FRONT PANEL .............................................................................4
BACK PANEL ...............................................................................7
REMOTE CONTROL ....................................................................8
EDID FUNCTION .........................................................................10
RS-232 & ETHERNET SERIAL INTERFACE ............................15
IR EXTENDER ...........................................................................16
TYPICAL APPLICATION .............................................................17
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
PACKAGE CONTENTS
Before connecting the unit, it is necessary to unpack it from the shipping carton and inspect the unit for any damage. While the cards are hot-swappable, it is recommended to install the cards before connecting the unit. This will make the installation easier.
• HD-88K Matrix Switcher
• RS-232 V2.0 / Ethernet V2.0 Protocol Instructions
• Master wireless IR Remote Control (SW-HD88K)
• 19 inch ear mount bracket (Part# 1U-440L)
• HD-100 IR Extender Receiver Set
• CD Contents: Manual, Windows GUI, ISP V1.0 Windows driver
• RS-232 Cable 6.5 feet (2M)
• HDMI Locking Post Replacement Screws
• Users Guide
• Power Supply Input: DC12V, 5A, (Worldwide Universal
100~240VAC, AC 50/60Hz)
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/ or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.
© Copyright 2016. All Rights Reserved.
Version 1.3 AUG 2016
HD88K-20150120-002
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
1
A NEU VIDEO
INTRODUCTION & FEATURES
INTRODUCTION
The HD-88K is a professional 8x8 matrix routing switch. Supporting (8) HDMI Inputs and (8) HDMI Outputs. The HD-88K is based on
HDMI standards and supports full resolution HDMI video with embedded HDCP and a signal bandwidth of 340Mhz, so there is no signal degradation. High definition digital signals can be selected and distributed to any of the (8) Inputs to (8) outputs. This switcher is certified as being fully CEC, ARC and HDCP 1.3 compliant, with full HD 4K2K HDMI V1.4a 3D formats and data rates up to 6.75Gbps. Supports
UXGA/WUXGA/DVI 1920x1200 resolutions to any HD display. The HD-88K has (1) HDMI connector per Input, effectively making this an
(8) In x (8) Out switcher. The EDID management can be selected between (7) different modes. Control is provided via front panel push buttons, IR remote, RS-232 or TCP/IP (not a web-browser). A RS-232/Ethernet Windows GUI software program is provided for matrix routing control (Windows only). This product has a 1 year warranty.
FEATURES
• (8) HDMI source devices matrix switched to (8) HDMI output destinations
• HDMI digital video w/ embedded HDCP, DVI formats and is CEC/HDCP 1.3 compliant
• Worldwide EDID control modes for HDMI, full 4K2K (24/30Hz) HD video resolutions
• Link speeds of up to 6.75Gbps (link clock rate of 340MHz), Supports HDMI 4K2K, 1.4a 3D formats
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,
1080i/p & 3860x2160p (24/30Hz)
• Compatible with all HDMI source devices, PC monitors, Plasma HD displays, HDTVs and audio receivers or audio amplifiers
• Digital video TMDS formats resolutions up to 4K2K with Deep color 36bit
• Using the build-in booster, each HDMI Output port is capable of driving cable lengths for 1080p up to 98 ft (30M) & 4K2K up to 66 ft (20M)
• Digital Audio Support: Dolby TrueHD, Dolby Digital, Dolby Digital Plus/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX, PCM, PCM2, LPCM2
• Various User Interface Control:
• Windows based GUI control via RS-232 port
• Front panel push button
• IR wireless remote control
• Ethernet switch control
• Third party RS-232 controller (via simple ASCII)
• Full function front panel controls: ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER
• Supports EDID Modes:
• Embedded EDID Modes: FSS/ H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz
• External Modes: External Modes: Learning mode-1 (Single Learning) & Learning mode-2 (Multiple Learning)
• Supports IR remotes and IR extenders for distances up to ~ 984 feet (300M) Maximum
• Supports Universal power adaptor AC100V~AC240V, 50/60Hz
The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be invoked.
2
A NEU VIDEO
SPECIFICATIONS
Specifications
• Type of Switcher: (8) Inputs to (8) Outputs HDMI Matrix Switch
• HDMI Support: HDMI 4K2K, 1080p@60Hz, 36bit Deep color, 3D of HDMI V1.4 formats
• HDCP / CEC Support: HDCP 1.3 Compliant, CEC Compliant
• Video Bandwidth: Double Data Rates: 340MHz, Total 6.75Gbps bandwidth
• Digital Video Supported: HD: 480i/480p/720p/1080i/p and 4K2K up to 36bit deep color
• Video Inputs: (8) HDMI (HDMI or DVI digital source)
• Video Outputs: (8) HDMI with Booster output for 1080p up to ~98 feet (30M) & 4K2K up to ~66 feet (20M)
• Audio Supported: Multi Audio Formats 5.1 / 7.1, MAT (MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6CH,
DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Switch Controls:
• Select & Function buttons on front panel (Data status via LCM panel show out)
• IR Remote Control (switch control)
• IR External port (switch control via 3.5mm OD Jack)
• RS-232 series interface (switch control)
• Ethernet series interface (switch control)
• Source Status: Input status LEDs indicates presence of a live signal
• Function Control Keys: ALL, OFF, RECALL, ENTER, MEMORY, LOCK, EDID, Destination button 1 thru 8, Source button 1 thru 8
• (7) EDID Management Modes:
• 1. Select Embedded EDID Modes: Mode1: FSS, Mode2: H24-3D, Mode3: H24-3D-M, Mode4: H36-3D, Mode5: H36-3D-M,
Mode6: 4K2K-3D, PCM-2CH, Mode7: DVI-D 1920x1200-60Hz
• 2. Select LEARNING Mode: Learning destination EDID to link source
• Infrared Frequency: 38KHz
• Video Booster: HDMI output for 1080p with lengths up to 98 feet (30M) / 4K2K up to 66 feet (20M)
• IR External Distance: ~984 ft/300M maximum
• HDMI I/O Connector: HDMI Type A - SMD 19pin female type
• Temperature: 32°F - 100°F Operation (0°C - 32°C)
• Dimensions (LxWxH): 17.5 x 10 x 1.75 in
• Rack Mount: 1RU High 19 in Rack Mount #1U-440L (with rack mount)
• Power Supply: DC12V, 5A, Power Input: AC 100~240VAC 50/60Hz (universal type supply)
• Safety Approvals: CE, FCC, RoHS, REACH
• Weight: 7.7 lb (Unit only) / 10.4 lb (Net)
As product improvements are continuous, specifications are subject to change without notice.
3
A NEU VIDEO
FRONT PANEL
FRONT PANEL
q
POWER SWITCH:
The power switch turns the unit ON and OFF. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked.
w
STATUS DISPLAY:
Front panel status display shows current matrix routing configuration. This same display also shows particular configuration settings depending on your current function. In run mode (as shown above), the display shows each Output (destination) channel and which Input (source) it is assigned.
e
IR SENSOR:
The IR sensor receives IR commands from the supplied remote control or third party IR emitter.
r
INPUT STATUS DISPLAY:
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
t
SOURCE SELECT BUTTONS:
Separate Inputs 1 thru 8 select buttons are provided each source selection.
y
EDID MODE SELECT BUTTONS:
Used to select EDID modes using Input buttons #1 and #2.
u
DESTINATION SELECT BUTTONS:
Separate Outputs 1 thru 8 select buttons are provided for each destination assignment. Routing can be source to destination or one source to multiple destinations.
Example: Press Destination 1, 3, 5 then press Source 2. It will route Input 2 to Output 1, 3, 5 respectfully.
i
19 INCH EAR MOUNT PAIR:
Converts desktop to 19 inch rack mount. Bracket (part # 1 U-440L) INCLUDED. Image shows rack mount bracket attached.
4
A NEU VIDEO
FRONT PANEL - EDID, MEMORY & RECALL
FRONT PANEL
o
FUNCTION KEY - EDID:
Used to display change current EDID mode.
- Press
EDID to select a new EDID mode.
- Press
SOURCE row #1 or #2 to select EDID modes.
- Press
ENTER to ready memory location.
- Or press
EDID again to cancel the operation.
Operation completes.
NOTE: Operation will abort if no keys are pressed within 5 seconds.
a
FUNCTION KEY - RECALL:
The system will show previously stored presets, up to a total of (16). Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Press the
RECALL button.
- Press
1 THRU 8 on either Source or Destination row.
- Press
ENTER. The pre-set configuration will execute.
Operation completes.
NOTE: Operation will abort if no keys are pressed with 5 seconds.
- Or press
RECALL again to cancel the operation.
s
FUNCTION KEY - MEMORY:
The system will show store presets, up to a total of (16). Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Configure desired matrices.
- Press the
MEMORY button.
- Press
1 THRU 8 on either Source or Destination row.
- Press
ENTER to ready memory location.
- Or press
MEMORY again to cancel the operation.
Operation completes.
NOTE: Operation will abort if no keys are pressed with 5 seconds.
- Or press
MEMORY again to cancel the operation.
5
A NEU VIDEO
FRONT PANEL - ALL, OFF, LOCK & ENTER
FRONT PANEL
d
FUNCTION KEY - ALL:
Disables (mutes) video on all destinations OR selects the same source to all destinations.
Option 1
- Press
ALL followed by the OFF button. The display will show “0“ indicating all destinations do not have video selected.
Option 2
- Press
ALL followed by Source 1 THRU 8. The display will show the source selected.
- Press
ENTER. The pre-set source selection will be assigned to all destinations.
f
FUNCTION KEY - OFF:
Disables (mutes) video to selected channels for either destination.
- Press the
OFF button followed by any Destination channel.
- Press
1 THRU 8 output destination. The display will show ”0“ for the selected channel indicating no video is selected.
g
FUNCTION KEY - LOCK:
- Press and hold
LOCK button for two seconds lockout the front panel.
- Press and hold
LOCK button for two seconds to enable the front panel.
h
FUNCTION KEY - ENTER:
Press
ENTER to confirm entries.
6
A NEU VIDEO
REAR PANEL
BACK PANEL
q
DC POWER INLET:
The switcher is fitted with a DC power plug input connector. Ensure that the plug used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A
Max (Center pin positive).
w
IR EXTENDER CONTROL:
Supports one IR extender. Extends a maximum distance of up to ~984 feet/300M. When you plug the external IR extender into the switcher, the front panel IR receiver remains active.
e
RS-232 CONNECTION:
RS-232 control port allows for interfacing to a PC, such as a computer or touch panel control, to the switcher via this DB-9pin female connector for serial RS-232 control.
r
ETHERNET CONNECTION:
ETHERNET control port allows for TCP/IP interfacing to a PC, such as a computer or touch panel control (not a web-browser), to the switcher via this RJ-45 female connector to control switcher.
t
INPUTS- 1, 2, 3, 4, 5, 6, 7, & 8 HDMI:
Connects a HDMI signal source to this Input. This HDMI port supports HDMI with embedded audio and DVI with AUX audio sources.
If you remove the HDMI screw posts, you must use the provided
HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI
Locking Post replacement screws will void your warranty.
y
OUTPUTS- 1, 2, 3, 4, 5, 6, 7 & 8 HDMI:
Connects a HDMI signal source to this Output. This HDMI port supports HDMI with embedded audio and DVI with AUX audio.
If you remove the HDMI screw posts, you must use the provided
HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI
Locking Post replacement screws will void your warranty.
7
POWER JACK: q
DC Jack - Inner OD Ø 2.1mm (+)
Outside OD Ø 5.5mm (GND)
Power input - 12VDC, 5A
IR EXTENDER JACK:
Female Jack - inner OD Ø 3.5mm
REMOTE PORT:
D-SUB-9pin female connector
REMOTE PORT:
Control the switcher RJ-45 female connector
ETHERNET PORT:
Note: The Ethernet port and
RS-232 port CANNOT be used simultaneously.
Any connection to the Ethernet port will disable serial commands sent to the RS-232 port.
HDMI CONNECTOR:
HDMI Type A SMD
19pin female socket connector
Note: With the proper adapters, the switcher can be used with DVI digital video signals.
HDMI CONNECTOR:
HDMI Type A SMD
19pin female socket connector
Note: With the proper adapters, the switcher can be used with DVI digital video signals.
A NEU VIDEO
REMOTE CONTROL
Before making any connections to the switcher. Observe the following:
• Ensure the main voltage supply matches the label on the supplied plug-pack (+/-10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output select the appropriate input source by using the front panel input select buttons. The supplied IR remote control. Or through the RS-232 serial communications port.
• Upon powering up the switcher, it will return to its last used setting before being powered down.
IR REMOTE CONTROL KEY
q
w
SWITCH POWER ON or OFF:
Power ON and OFF
e
DESTINATION: 1 thru 8 OUTPUT SELECTION:
Destination buttons to select the output display channel
r
SOURCE: 1 thru 8 INPUT SOURCE SELECTION:
Input 1~ 8 source selection buttons
t
FUNCTION KEY:
Function selection buttons
ALL OFF EDID
MEMORY ENTER LOCK
RECALL
8
A NEU VIDEO
REMOTE CONTROL
IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
HOW TO SETUP IR CODES:
Model Number: HD-88K
CUSTOM CODE : 8A75
POWER ON: 8A75 A15E
POWER OFF: 8A75 A25D
ALL:
OFF:
EDID:
LOCK:
8A75
8A75
8A75
8A75
B04F
B14E
B748
B54A
RECALL: 8A75 B24D
MEMORY: 8A75 B44B
ENTER: 8A75 B34C
PRESS DESTINATION then - # PRESS SOURCE - #
DESTINATION #1 : 8A75 10EF
DESTINATION #2 : 8A75 20DF
DESTINATION #3 : 8A75 30CF
DESTINATION #4 : 8A75 40BF
DESTINATION #5 : 8A75 50AF
DESTINATION #6 : 8A75 609F
DESTINATION #7 : 8A75 708F
DESTINATION #8 : 8A75 807F
For Example:
Select Destination # 1 to Show Source #1~8,
The IR Data Code List:
Destination # 1, Source #1 8A75 10EF 8A75 01FE
Destination # 1, Source #2 8A75 10EF 8A75 02FD
Destination # 1, Source #3 8A75 10EF 8A75 03FC
Destination # 1, Source #4 8A75 10EF 8A75 04FB
Destination # 1, Source #5 8A75 10EF 8A75 05FA
Destination # 1, Source #6 8A75 10EF 8A75 06F9
Destination # 1, Source #7 8A75 10EF 8A75 07F8
Destination # 1, Source #8 8A75 10EF 8A75 08F7
SOURCE #1 : 8A75 01FE
SOURCE #2 : 8A75 02FD
SOURCE #3 : 8A75 03FC
SOURCE #4 : 8A75 04FB
SOURCE #5 : 8A75 05FA
SOURCE #6 : 8A75 06F9
SOURCE #7 : 8A75 07F8
SOURCE #8 : 8A75 08F7
9
A NEU VIDEO
EDID FUNCTION
EDID function Setup
EDID SETUP
Step 1. Press the EDID button
TO CHANGE THE EDID SETUP
The display will show the currently selected EDID mode
Step 2. Press SOURCE #1 or #2 button row
Step 3. Press the ENTER button
The button will flash blue and the display will show the current Embedded EDID Status.
To set EDID mode.
The switcher will return to operation mode.
Operation will abort if no keys are pressed within 5 seconds.
EDID STATUS
Step 1.
Press the EDID button
TO VIEW THE CURRENT EDID STATUS
The button will flash blue and the display will show the current Embedded EDID Status.
Step 2.
Press the EDID button To exit.
EMBEDDED EDID MODES
Embedded EDID setup
Press
EDID > SOURCE > ENTER
TOTAL 7 EDID MODES
To select Embedded EDID mode or LEARNING mode
Press EDID button: The LCM will show the current EDID status.
SOURCE #1 or SOURCE #2
Repeatedly pressing the SOURCE 1 button will cycle UP thru the options.
Repeatedly pressing the SOURCE 2 button will cycle DOWN thru the options.
Select Embedded EDID :
Mode 1 : FSS Mode 5 : H36-3D-M
Mode 2 : H24-3D Mode 6 : 4K2K
Mode 3 : H24-3D-M Mode 7 : DVI-D 1920x1200-60Hz
Mode 4 : H36-3D
RESET
How to RESET EDID mode
Press
EDID > RECALL > ENTER
EDID RETURN TO FACTORY DEFAULT
RESET To the FACTORY DEFAULT (1080p-2CH).
Press EDID Button: The LCM will show the current EDID status.
Press RECALL Button: The LCM will show the RESET EDID.
Press ENTER to confirm entries.
The EDID will return to FSS mode and resolution 1080p-2CH.
HOW TO SETUP FSS
®
FUNCTION
Step 1.
Press the Destination
#1~8 button row
Then Press the Source
#1~8 button row
Step 2.
Press the EDID button
Step 3.
Press ENTER button
Step 4.
Press the EDID button
Step 5.
Press ENTER button
FAST SPEED START
®
To setup and Install all devices.
Select a optimum status of
To conform entries.
To select the EDID
FSS
®
To conform entries.
Embedded EDID mode.
mode.
10
A NEU VIDEO
EDID FUNCTION
EDID FUNCTION: (7) EMBEDDED EDID MODES
Mode 1. FSS
®
(Fast Speed Start)
Mode 2. H24-3D (1080p-24 bits)
Fast Speed Start
®
mode shortens the startup time of the switcher. Selecting this mode does not force the EDID setup to be cancelled. Users may first select one EDID Mode from Mode 2 to 3, and then select Mode 1 for fast speed start
®
.
Audio Support: PCM 2CH
Mode 3. H24-3D-M (1080p-24bits)
Mode 4. H36-3D (1080p-36 bits)
Mode 5. H36-3D-M (1080p-36 bits)
Mode 6. 4K2K (24/30Hz)
Mode 7. 1920x1200-60Hz (DVI-D)
Audio Support MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Audio Support: PCM 2CH
Audio Support: MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3
5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
HDMI Support: 4K2K-3D, PCM 2CH (3860x2160-24/30Hz)
Audio Support: PCM 2CH
DVI Support: DVI-D 1920 x 1200 60Hz
11
A NEU VIDEO
EDID FUNCTION
EDID Function: LEARNING
LEARNING EDID SINGLE TO SINGLE
Step 1.
Press the
EDID button
EXAMPLE: LEARN DESTINATION #4 EDID TO SOURCE #2.
The button will flash blue and the display will show the current Embedded EDID Status.
Step 2.
Press the
DESTINATION #4 button row
Step 3
. Press the SOURCE #2 button row
Step 4.
Press
ENTER button
LEARNING EDID SINGLE TO MULTIPLE
Step 1.
Press the EDID button
Step 2.
Press the Destinations #1~8 button row
Step 3.
Press the Source #1 ~ #8 button row
Step 4.
Press ENTER button
LEARNING EDID SINGLE TO ALL
Step 1.
Press the EDID button
Copy the Destination #4 Display EDID.
Learning the Destination #4 EDID to Source # 2.
To confirm entries.
LEARNING DESTINATION EDID LINK TO THE MAJORITY SOURCES
The button will flash blue and the display will show the current Embedded EDID Status.
Copy any 1~8 Destinations EDID.
Learning the Destination EDID link to source #1 ~ #8.
To confirm entries.
LEARNING DESTINATION EDID LINK TO ALL SOURCES
The button will flash blue and the display will show the current Embedded EDID Status.
Step 2.
Press Destination button
1 THRU 8
Step 3.
Press ALL button
Learning anyone 1~8 Destination EDID to all sources.
Learning selected destination EDID to all sources.
Step 4.
Press ENTER button To confirm entries.
LEARNING EDID DEFINITION LEARNING EDID FROM DESTINATION TO SOURCE
1. Switcher will LEARN destination EDID and pass the selected source.
2. To set up learning between a single destination and single source:
Press EDID button > Press DESTINATION 1 THRU 8 > Press SOURCE 1 THRU 8 > Press ENTER to confirm.
Switcher will learn destination EDID to source device.
3. To set up learning between a single destination and Multiple sources:
Press EDID button > Press DESTINATION 1 THRU 8 > Press the majority SOURCES 1 THRU 48 > Press ENTER.
Switcher will learn single destination EDID to many source devices.
4. How to Learning single destinations with all sources. Press EDID button > Press ALL button > Press ENTER to confirm.
MULTIPLE LEARNING #2 DEFINITION MULTIPLE LEARNING EDID FROM DESTINATION TO SOURCE
1. Switcher will multiple LEARN destination EDID and pass the selected source.
2. To set up multiple learning between a single destination and single source: Press EDID button > Press OFF button > Press
DESTINATION 1 THRU 8 > Press ENTER to confirm. Switcher will learn destination EDID to source device.
3. When the Source has “Learned” the EDID data from a destination, it will save that EDID information into EPROM and the EDID data will not change. To change a saved HDMI EDID information, you have to select a new LEARNING destination to source or Disable the
LEARNING.
12
A NEU VIDEO
EDID FUNCTION
EDID SINGLE LEARNING MODE
1
LEARNING EDID MODE-#1 LEARNING EDID FROM DESTINATION TO SOURCE
Single Learning Mode#1 EDID setup
Press
EDID > DESTINATION > SOURCE > ENTER
1. Press the EDID button: The LCM will show the current EDID status.
Key Press Sequence:
EDID > DESTINATION # > SOURCE # > ENTER
The EDID for HDMI has been learned from the
Destination port to the Source port.
2. Press the DESTINATION 1-8 button: The LCM will show LEARNING
HDMI. The switcher will LEARN the destination HDMI EDID.
3. Press the SOURCE 1-8 button: The switcher will Learn destination HDMI
EDID and pass to the selected source.
4. Press the ENTER button to confirm changes. The LCM will return to the default screen showing selected matrix routing status.
NOTE: The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.
For Example: When the source has “Learned” the EDID data from a destination, it will save that EDID information into EPROM and
the EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPROM.
13
A NEU VIDEO
EDID FUNCTION
EDID SINGLE LEARNING MODE 2
LEARNING EDID #2 PASSING EDID FROM DESTINATION TO SOURCE
Multiple Learning mode #2 EDID setup
1. Press the EDID button: The LCM will show the current EDID status.
Key Press Sequence:
EDID > OFF > DESTINATION #1 thru #8 > ENTER
The EDID for HDMI has been Learned from the
Destination port to the Source port.
2. Press the OFF button: The LCM will show the current EDID LEARN status.
3. Press the DESTINATION 1-8 button: The switcher will LEARN destination
HDMI EDID and pass to the selected source. The switcher will Enable or Disable
HDMI EDID for the selected source.
4. Press the ENTER button to confirm changes. The LCM will return to the default screen showing selected matrix routing status.
NOTE: When the Source has “Learned” the EDID data from a destination, it will save that EDID information into EPROM and the EDID
data will not change. To change a saved HDMI EDID information, you have to select a new LEARNING destination to source or Disable the LEARNING.
14
A NEU VIDEO
ETHERNET & rs-232 SERIAL INTERFACE
ETHERNET / RS-232 SERIAL INTERFACE CONNECTS a PC or CONTROL SYSTEM
VERSION COMPATIBLE V2.0
For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
Example of the commanded string to select Inputs:
FUNCTION
Select source
COMMAND EXAMPLE
Source 001;
COMMAND
Source xxx;
RESPONSE
Source 001#ok;
VARIABLES
xxx = Input Channel (001=Source1, 002=Source2.etc)
DESCRIPTION
Select source number 1
Note: Control the switcher
SPD: Speed
LINK: Ethernet link
RJ-45 Female 8P-8C Connector
4
5
6
7
ETHERNET SERIAL INTERFACE
Pin Ethernet Reference
1 TXOP TX +
2
3
TXON
RXIP
TX -
RX +
NC
NC
RXIN
NC
RX -
8 GND
TCP, Port 5000
ETHERNET TCP/IP PROTOCOL COMMANDS ( Ethernet / RS-232 Control driver V2.0 )
*** The Ethernet port and RS-232 port cannot be used simultaneously. Any connection to the Ethernet Control port will disable serial commands sent to the RS-232 port.***
HD-88K
Device
RS-232 Configuration
RS-232 cable is a straight thru cable and not null-modem
Definition Pin
TX
RX
GND
1
2
3
4
5
6
7
8
9
5
6
3
4
7
8
9
Pin Definition
1
2
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
PC
RS-232 SERIAL INTERFACE PROTOCOL COMMANDS ( Ethernet / RS-232 Control driver V2.0 )
The HD-88K switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system. The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
15
A NEU VIDEO
IR EXTENDER
REAR PANEL IR EXTENDER PORT
1. HD-100 IR 300M Receiver
Switcher IR EXT. In Cable (3C) IR Receiver (HD-100)
Distance: Max.300M
IR PN#: SW-HDXX
R oHS /95/E C
R S -232 IR E XT. in
INP UT
DC 12V
RS - 232 IR EXT .
IR Rx
HD-100
I M
AT
HD-100
IR Receiver Set
HD-100 Maximum Distance ~ 984 feet (300M)
Control Switch HD-XX
The HD-100 IR Receiver is required when using the port “ALL in” Jack.
SW
IR
2. HD-100C IR 2M Receiver
Switcher IR EXT. In Cable (2C) IR Receiver (HD-100C)
IR Receiver cable 6ft (2M)
Distance: Max.(2M)
R oHS /95/E C
IR PN#: SW-HD-XX
R S -232 IR E XT. in
INP UT
DC 12V
RS - 232 IR EXT .
IR Rx
HD-100
HD-100C
IR Receiver Cable
I M
AT
SW
IR
Control Switch HD-XX
The HD-100C IR Receiver will not function on the port “ALL in” Jack.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
Pin configuration for IR 984 feet (300M) Extender Receiver such as HD-100 compatible
VCC (Ring)
Tip: Signal
Ring :VCC
Sleeve: GND
Tip Ring
Ring
Sleeve
GND (Sleeve)
Sleeve
Tip (center)
Signal (center)
HD-100
IR Receiver Set
HD-100 Receiver and HD-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
Pin configuration for IR Receiver 6 feet (2M) cable such as HD-100C compatible
IR Receiver cable 6ft (2M)
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Tip Ring
Ring
HD-100C
IR Receiver Cable
Sleeve
Tip (center)
Signal (center)
HD-100 Receiver and HD-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
GND (Sleeve)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
16
A NEU VIDEO
TYPICAL APPLICATION
INSTALLING DIAGRAM
Samples Connection:
Using external IR, RS-232 or Ethernet commands to control the HD-88K via PC or HD-100 IR receiver transmit the HD-88K’s IR signal.
NOTE:
1. Switcher IR External port: Use HD-100 IR signal Receiver.
2. 4K2K Source: Use 4K2K Blu-ray HD Source.
3. Control Switch via a PC RS-232.
4. Control Switch via a PC Ethernet.
Application RS-232, IR and Ethernet control the Switcher.
17
A NEU VIDEO
TERMS & CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.
A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
18
Advertisement
