Graco 4113 User's Manual

The Entertainer
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
™
Activity Center
PARTS LIST
CHECK that you have all the parts listed
below BEFORE assembling your
Entertainer™ activity center. If any parts
are missing, call Customer Service at
1-800-345-4109.
by
OWNER’S
MANUAL
Tool required: Screwdriver
Model No. __________
Serial No. __________
Dear Customer,
Please fill in the
model and serial
numbers above
from the label
under the tray
of your new
Entertainer™
activity center.
Never leave child unattended. Always
keep child in view while in this product.
Never lift or carry this product with
child in it.
Do not use product with a child who
can tip over or climb out of product.
Model 4113
Congratulations on your purchase of a
Graco® Entertainer™ activity center!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco®
Entertainer™ activity center is a wise
choice, promising many hours of
enjoyment for your baby.
Before using your activity center, please
take a few minutes to read this Owner’s
Manual. The short time you spend reading
these instructions will help you to use your
activity center properly.
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our
Customer Service Department at 1-800-345-4109.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts,
use or maintenance. When you call, please have
the model and serial numbers ready so your
call may be processed quickly and efficiently.
Clicker
and screw
Seat
Seat lock
and screw
Leg (3)
Strings can cause strangulation! DO
NOT place items with a string around
your child’s neck, such as hood
strings or pacifier cords. DO NOT
suspend strings over the activity
center or attach strings to toys.
Product may gradually move across
the floor as child plays in it. Watch for
movement of product and be sure
child stays away from hazards in the
area such as stairs, cords, hot liquids,
pools, sources of heat and anything
else that may injure your child.
To avoid tipovers, place product on
flat, level floor/ground. Adjust legs to
same height so that the tray is level
before placing child in product.
Tray and seat ring
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
Customer Satisfaction
Beads and bar
Teether
toy
Base
CARE AND MAINTENANCE
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT.
If you experience any difficulties, please contact the Customer Service Department.
KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted,
unable to walk, weighs less than 30 pounds, and is less than 32 inches tall.
EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
FROM TIME TO TIME CHECK YOUR ACTIVITY
CENTER for loose screws, worn parts, torn material
or stitching. Replace or repair the parts as needed.
Use only Graco® replacement parts.
REMOVABLE CLOTH SEAT may be machine
washed in lukewarm water on delicate cycle and
drip-dried. DO NOT MACHINE DRY. NO BLEACH.
TO CLEAN FRAME, use only household soap or
detergent and warm water. NO BLEACH.
DO NOT USE THIS PRODUCT if it is damaged or broken.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
© 1997 Graco 281-6-97
2
3
4
To Assemble Your
Entertainer™ Activity Center
Step 6.
Turn tray over. Push one leg into socket in tray exactly as
shown until it snaps into place. Repeat for other two legs.
Step 1.
Step 9.
Insert
this
end
first
Assemble the toys on the tray as shown.
NOTE: Toys may be removed from tray
for cleaning or storage.
Turn the tray over and
locate the hole that the
seat lock screws into. Place
the seat lock on the tray as
shown and screw it to the
tray. DO NOT overtighten
screw—seat lock must be
free to slide.
Retaining
loops
Button
faces seat
Step 2.
RIGHT
Four tabs are located
behind the indentations
inside the seat ring.
Remove the seat ring by
pulling the four tabs out
from under the tray, one
at a time, while lifting the
seat ring.
WRONG
Push beads firmly over the
retaining loops on bead bar.
Insert end with loops into the
hole directly over leg, and turn
bar until fully seated (retaining
loops do not go into the hole).
Then plug forked end of bar
into the square hole in the tray.
Insert teether
stalk into the tray.
Step 7.
Solid color inside
On top of tray, CHECK that
snaps are visible through
slots. Pull on leg to be sure it
is securely attached.
Step 3.
Put the seat ring upside
down inside the cloth seat.
The high side of the seat
ring goes to the back of the
seat, where the warning
label is located.
Attach the seat to the seat
ring by tucking the seat
edge into the channel and
snapping the grommets on
the pegs.
Snaps visible
Step 8.
Slide the leg tubes on the tray onto the leg tubes on the
base as shown.
Grommet
Pattern side
HINT: If a tray leg tube will not slide onto the base leg
tube, twist the base tube slightly to line up the parts.
Push in the buttons on each of the upper leg tubes
and adjust the activity center to the desired height.
The bottom edge of the upper tubes must be even with
one of the three lines on the lower leg tube.
Pattern side UP
Step 4.
CHECK that all three leg tubes are set to the same
height.
Turn the seat over and
push the seat down into the
seat ring.
Step 5.
Snap the seat ring back
onto the tray. Make sure all
four tabs are snapped onto
the inside lip.
Tighten screw until
clicker does not
move freely—DO
NOT overtighten—
then loosen screw
slightly.
To Use the Seat Lock
To Adjust the Seat Height
Push gently on latch and
turn the seat until latch
engages in one of the four
stop positions.
activity center.
Step 1.
To allow seat to swivel
again, pull lock out.
Buttons
Do not adjust height while child is in
Press in the buttons on
each leg to adjust seat
to desired height. The
bottom edge of the upper
tubes must be even with
one of the three lines on
the lower leg tube.
Line
For your child’s safety, all three legs
must be set to the same height. Tray must be level.
281-6-97
5
6
7
8
Replacement Parts
Step 2.
After adjusting height of the seat, CHECK that your
child’s feet can rest completely on the floor of your
activity center. Tray should not be too high or too low.
Remove child and readjust height if necessary.
Instructions for ordering activity center parts:
Complete form below. Your model number MUST be
included on the form to ensure proper replacement parts.
Your model number can be found on a sticker on the bottom
of the tray. Payment must accompany your order.
Price:*
Parts List:
Tray at proper height
Teether toy ................................................... $ 5.00
Beads and bar ............................................. $ 5.00
Clicker and screw ........................................ $ 5.00
Cloth seat ..................................................... $14.50
Seat ring and bearings ................................ $ 7.00
Seat lock and screw ..................................... $ 5.00
Complete tray unit (with legs, height .......... $25.00
springs and height buttons)
Height buttons and height springs only ...... $ 5.00
Retainer rings ............................................... $ 5.00
Spring covers with upper and lower trim .... $ 5.00
Complete base unit (with legs, retainer ...... $20.00
straps, boots, and retainer rings)
* Prices subject to change
without notice.
TRAY TOO HIGH
TRAY TOO LOW
IF YOU NEED HELP
If you have any questions, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
MAIN STREET
ELVERSON, PA 19520
Model Number
(Must be filled in)
Teether toy
Beads and bar
Clicker and screw
Cloth seat
Seat ring and bearings
Seat lock and screw
Complete tray unit
Height buttons and
springs
Retainer rings
Spring covers
with trim
Complete base unit
9
Name
Address
City, State, Zip
(
)
Telephone
Check enclosed
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Total:
Account #:
6% sales tax
(PA only):
Expiration date:
Total amount
due:
281-6-97
SHIP TO:
Signature:
10

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project