advertisement
LCD TV
OWNER' S MANUAL
MODEL: L E 2 4 T 1 0 0 0 F
Please READ this manual carefully before operating your TV, and retain it for future reference
Contents
1、 Safety and warnings..........................................................................................................2-3
2、 Introduction.....................................................................................................................4
3、 Installation...................................................................................................................... 5-8
4、 Remote Controller........................................................................................................... 9
5、 TV Operation..................................................................................................................10-12
6、 Trouble shooting............................................................................................................. 13
-1-
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings, install in accordance with the instructions.
8) Do not install near any heat sources such as radiations, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protected the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Unplug this apparatus during lighting storms or when unused for long periods of time.
13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14) Mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
15) The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted candles, should be placed on the apparatus.
17) Attention should be drawn to the environmental aspects of battery disposal.
18) The use of apparatus in moderate climate.
19) The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
SAFETY AND WARNINGS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK).NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The symbol indicates that dangerous voltages constituting a risk of electric shock are present within this unit.
The symbol indicates that there are important operating and maintenance instructions in the literaturaccompanying this unit.
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
WARNING:
The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only
identical replacement parts.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
Never stand on, lean on, or suddenly push the television or its stand. You should pay special attention to children.
Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose the television receiver to rain or moisture.
Do not place your television on an unstable cart, stand, shelf or table. Serious injury to an individual , and damage to the television, may result if it falls.
Do not drop or push objects into the television cabinet slots or openings. Never spill any kind of liquid on the television receiver.
When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet.
Do not block the ventilation holes in the back cover.
Adequate ventilation is essential to prevent failure of electrical components.
Avoid exposing the television receiver to direct sunlight and other sources of heat. Do not stand the television receiver directly on other products which give off heat, e.g. video cassette players and audio amplifiers. Do not place naked flame sources, such as lighted candles on the television.
Do not trap the power supply cord under the television receiver.
-3-
Dim:515*320mm(不包括底座)
If the television is to be built into a compartment or similar enclosure, the minimum distances must be maintained. Heat build-up can reduce the service life of your television, and can also be dangerous.
Main features
① Used as Television, display terminal, PC display;
② High luminance, wide viewing angle;
③ Can store Air and Cable TV programs;
④ HDMI interface;
⑤ Multi-Media player (USB);
INTRODUCTION
Accessories
Infrared Remote Controller............ 1
Battery(AAA)...............................2
RF Extension Head . . .....................1
Main parameter
Viewing Picture Size (Diagonal)
Resolution
Aspect Ratio
TV System
Video Signal System
Receiving Channel
Input Power Voltage
Power consumption
Audio Output Power(THD 7%)
Signal Input
Horizon tal definition(TV line )
24inch
1920x1080
16 : 9
PAL M, PAL N, NTSC
PAL/NTSC/SECAM
Air 2-69
Cable 1-125
AC 100-240V 50/60Hz
40W
2 x 3W
Analog RGB(VGA) x 1
High-Definition Multimedia Interfac e (HDMI) x 1
Composite Video Input x 1
Composite Video output x 1
Audio Input x 2
YCb (Pb )Cr (P R) x 1
USB x 1
RF x 1
Composite Video input >=350
Y Cb(Pb ) Cr(Pr) >=400
-4-
INSTALLATION
Front panel
KEYBOARD
2
3
1
SOURCE
MENU
CH+
CH-
3
VOL+
4
VOL-
STANDBY 5
1
2
30 30
SOURCE MUTE
PICTURE AUDIO ASPECT SLEEP
MENU
VOL-
INFO
VOL+
OK
CH-
CC MTS EXIT
CH+
RECALL
REW FWD PREV NEXT
1: Remote control sensor.
2: Indicator LED: BLUE POWER ON.
RED STANDBY.
3: Key board
REAR AV Connections
1.SOURCE:
Display the input source menu.
2.MENU:
Display main MENU.
3.CH+/CH-
In TV mode,press“CH+”or“CH-”to change
the channel up and down.
In MENU mode, press “CH+”or“CH-”to select
items.
4.VOL+/VOL-
Adjust sound level.
In MENU mode, press“VOL+”or“VOL-”to
adjust the item that you selected.
5. STANDBY
Press this button to turn the unit ON from
STANDBY mode.
Press it again to turn the set back to STANDBY.
VIDEO
AV IN
L R VIDEO
AV OUT
L R
All the terminals are (from left to right):
VIDEO, AUDIO INPUT, AV OUTPUT.
Note: VIDEO and YPbPr share one audio channel.
REAR AV Connections (SIDE)
USB HDMI
Y Pb Pr HEADPHONE
PC AUDIO
VGA
All the terminals are (from left to right):
USB, HDMI, YPbPr INPUT, HEADPHONE, PC AUDIO, VGA, RF.
Note: When HDMI port get DVI signal, the audio signal receives from the PC
Audio channel.
-5-
ANT
INSTALLATION
ANTENNA
Note:
Aerial connections: IEC(female).
Input impendance: 75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are Power off.
1.Connect VGA and audio cable
2.Connect power cord
3.Power on the TV, switch to PC mode
4.Power on the PC
This sequence is very important.
USB HDMI
Y Pb Pr HEADPHONE
PC AUDIO
VGA
ANT
8
-6-
PRESET MODE (PC)
RESOLUTION
1 800*600
2
3
1024*768
1280*768
4
5
1360*768
1920*1080
NOTE: PC V.Freq.(Hz) not more than 60Hz.
PRESET MODE (HDMI)
RESOLUTION
1 800*600
2 1024*768
3
4
5
1360*768
1280*768
1920*1080
V.Freq.(Hz)
60
60
60
60
60
V.Freq.(Hz)
60
60
60
60
60
-7-
H.Freq.(KHz)
37.88
48.36
47.3
47.7
67.5
H.Freq.(KHz)
37.88
48.36
47.7
47.3
67.5
INSTALLATION
INSTALLATION
AV EQUIPMENT
This TV provides two group of AV, one group of YPbPr for convenient connection to VCR, DVD or other video equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.
ANT
USB HDMI
Y Pb Pr HEADPHONE
PC AUDIO
VGA
G B R
HDMI
VIDEO EQUIPMENT with YPbPr
G B R W R
W R
Y Yellow (video)
R Red (audio R)
W White(audio L)
R Red(Pr or Cr)
B
G
Blue(Pb or Cb)
Green(Y)
VIDEO
AV IN
L R VIDEO
AV OUT
L R
W R
Y W R
VIDEO EQUIPMENT
W R Y
TO AUDIO OUTPUTS
TO VIDEO
OUTPUTS
W
VIDEO EQUIPMENT
R
TO VIDEO
INPUTS
TO AUDIO INPUTS
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game or stereo system, etc...
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note: 1.AV and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
4 .When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT signal is AV; other
sources have no AV OUT signal.
-8-
6
7
8
9
10
11
12
REMOTE CONTROLLER
The remote control cannot be operated unless the batteries are properly loaded inserted.
When using the remote control, aim it at the remote control sensor on the TV.
Function introduction
1
2
4
5
SOURCE MUTE
PICTURE AUDIO ASPECT SLEEP
MENU
VOL-
INFO
VOL+
OK
CHCH+
CC MTS EXIT RECALL
REW FWD PREV NEXT
3
13
14
15
16
17
18
19
1.Press to turn on and off the TV.
2.SOURCE:To select input source.
3.Switches the TV sound on or off.
4.Press repeatedly to cycle through the available picture modes.
5.Press to cycle through the different sound mode settings
6.Press to change a channel.
7.Press to open the on-screen menu
8:Press CH+ or CH- to go to the next or previous channel, Press VOL+ or VOL- to increase or decrease the volume.
9.Press to activate the NTSC TV sounds, such as Stereo
SAP or Monotone
10.Press to turn on or off the closed captions.
11. Rewind Forward Previous
Next in USB mode
12.
Play/Pause Stop
13.Press to display the sleep timer option.
14.To change the picture aspect ratio: Auto/4:3/16:9/
Zoom/Zoom2.
15
.
Press to display the TV status information on the bottom.
16.Press to confirm selections in an on-screen menu or to open a submenu.
17.To move within the menu.
18.Exit On Screen Display.
19.Press to go to the last viewed channel.
-9-
1. CHANNEL MENU
The first item of the MENU is channel menu ( for
TV source only).
You can search channels and edit programs here.
Press to move, press OK button to confirm, and press to adjust.
Auto Tuning
Antenna
Skip
MTS Mode
TV OPERATION
3. SOUND MENU
The third item of the MENU is the SOUND
MENU.
You can adjust the sound effect here such as treble, bass, balance etc.
Press to move, press OK button to confirm, and press to adjust.
Sound Mode Standard
Balance
Auto Volume
Surround Sound
1).Auto tuning:
Search all the TV channels automatically.
2). Antenna
There are air and cable, you can changed.
3). Skip
Press OK button to skip cunent channel.
4). MTS mode
Press OK button to choose the MTS mode.
5). Software update(USB):
Update the TV set a software by USB.
2. PICTURE MENU
The second item of the MENU is PICTURE MENU.
You can adjust picture effect here, such as contrast, brightness, etc.
Press to move, press OK button to confirm, and press to adjust.
Picture Standard
Color Temperature
Aspect Ratio
Noise Reduction
PICTURE
Screen
< >
Note:
Auto volume: only available when the input signal volume is too large or distortion.
4. TIME MENU
The forth item of the menu is the TIME MENU
You can adjust the clock, power on/off time, sleep time etc.
Press to move, press OK button to confirm, and press to adjust.
Clock -- -- -- --
Off Time
On Time
Sleep Timer
NOTE:
Within 15 minutes there is no signal, the TV will auto sleep.
Once you power off the TV set by AC, the clock time will be reset.
5.OPTION MENU
The fifth item of the MENU is the OPTION MENU.
You can adjust the OSD language or Restore factory default, or Caption or Blue Screen.
NOTE:
1).Tint is available in NTSC system only.
2).There are four color temperature modes can be selected, such as medium, warm, cool, and user.
3).Screen is available in PC mode only, which can adjust horizontal position, vertical position, size and phase.
-10-
OSD Language English
Restore Factory
Caption
Blue Screen
TV OPERATION
Press the to select the right disk and press OK to display media files and folder list or choose Return to back to the media type selection menu.
1/1
NOTE:
Restore factory default will clear all the programs and Reset all the settings to default value.
6. USB MENU
OK
Press OK button to enter the USB menu.
USB 2.0
Input Source
TV
YPbPr
PC
HDMI
AV
USB
PHOTO MUSIC MOVIE TEXT
Please make sure that the USB device have plugged in the slot.There are four type media item can be selected, such as photo, music, Movie, and text. Select the type media item by pressing , press OK button to enter the disk selection menu.
1/1
Return
Resolution: 688x412
AudioTrack: 1/2
Subtitle: 1/3
Program: 1/5
Size: 511457 KBytes
Movies
Sample1.ts
Sample1.ts
Sample2.ts
Sample3.ts
Sample4.ts
Select the media file by pressing or , then the preview frame will pop up.Press the button
to play the media file in full screen.When the media file (photo,music, Movie, or text type) is playing, press the OK or Info button can display the control bar.
00:00:33/00:04:22
Pause
Press to select the function icon, press OK button to confirm the function.
Press or EXIT button to exit the control bar.
NOTE:
You can adjust the audio track, subtitle, or program in the Info menu while Playing the video file.
Choose the Info icon and press OK can display the Info MENU.
Sample1.ts
Resolution: 720x576
Audio Track: 1/2
Subtitle: 1/3
Program: 1/6
Size: 30574 KBytes
Close
Return C
-11-
Hotel Mode:
Please press source key first,and then press number key
“1001” to enter into Hotel Mode.
Hotel Mode Operation
Hotel Mode Operation
Panel key lock
Max volume
Start Source
Start Channel
Setup Menu display
Input source change
Save To USB
Load
Volume default
OFF
OFF
100
TV
1
Yes
Yes
0
Hotel Mode Operation : Set Hotel mode on/off.
Panel key lock : Keypad will be locked, when Key Lock mode is on.
Max volume: Set max volume limitted.This option allows you to set the Max Volume Level.
Start Source:Choose source, the options as follow:
TV/YPbPr/PC/HDMI/AV/USB, press the ◄ or ► button to select the desired source.
Start Channel : In TV mode, you can select a channel number to be set as the TV present channel. Press the ◄ or
► button to select the desired channel number .
Setup Menu display :Main menu lock , main menu will not display when set to “No”
Input source change : Source lock,you can't change the source, when set to “No”
Save To USB: Backup all TV setting data to USB disk.
(backup file named DATABASE.bin)
Load: Restore this data to TV from USB disk. When restore is executed,the TV will reboot.
Volume default : Power on default volume, press the ◄ or
► button to select the desired volume.
-12-
TV OPERATION
Interfere
Normal Picture
No picture
No color
TROUBLE SHOOTING
Trouble phenomenon
Picture Audio
Snow Noise
Inspection
antenna position, direction
or connection
Ghost
Normal audio
antenna position, direction or connection
Noise
electronic equipment,car/ motorcycle,fluorescent light
Mute
Mute
Volume(inspect wether the mute function on the remote control are started , or audio system are correct or not)
Power cord is not inserted
Power switch is not opened
Contrast and brightness/volume setup
Press standby key on the remote control for inspecting
Normal audio color control
Scramble
Normal audio or weak
retune channel
No color
Noise
Audio system
Special Explanation:The accessories such as remote control is not belongs to the guarantee.
-13-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project