- Home
- Domestic appliances
- Large home appliances
- Water heaters & boilers
- Haier
- FCD JTHA30- ET
- User's manual
advertisement
Little Sea-ox
Haier Household Electric Water Heater User's Manual
Group
Qingdao Economic and Technological Development
District Haier Water Heater Co., Ltd.
Haier Garden, Qianwangang Road, Economic Development
Zone,Qingdao, P. R. China
FCD JTHA30-
FCD JTHA40-
FCD JTHA50-
FCD JTHA60-
FCD JTHA80-
ET
ET
ET
ET
ET
Please read this manual before usage
Retain it for future reference HAIER
THERMOCOOL
Pre-safe Expert
Mark
of
Haier
Safe
Water Heaters
This mark is the designation for Pre-safe Expert of Haier
Water Heater Company, which indicates use of the company's patented technology inside the product. It ensures you a safe bath while monitoring whether your house ground wire is live or not all the time. If this mark is lighted on, it indicates your house ground wire has come live (poor grounding and live). In this case, please immediately stop use and unplug from the power supply, and remember not to touch any electric appliance shell in your house. At the same time, immediately contact aftersales service and your property management company for professional repair until the mark goes off.
Pre-safe Expert will become the electric safeguard for your family.
Contents
Before usage
Features
Parameters
Dimensions
Electric circuit diagram
Safety precautions
Setting environment 5
Installlation
Installation
Attentions in instruction
Operation instructions
Attentions in operation
FAQ
Cleaning and maintenance
FAQ
Packing list
Note
See to the physical product for the appearance, color or pattern.
Packing List
Name
Electric water heater
(set)
Safety valve
(pcs)
Drain hose
(ply)
Expansion
bolt
(pcs)
Expansion
hook
(pcs)
User's manual
(copy)
Quantity
Note
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and Maintenance
Statement: This water heater shall only be repaired and maintained by qualifie servicemen.
Improper maintenance may cause severe injury or damage. Before opening or repairing water heater, please do pull out the power plug.
Note: Before asking for service, please refer to troubleshooting section to resolve easy problems.
External Cleaning: Disconnect power supply before cleaning. Gently wipe with wet cloth dipped with a little of mild detergent. Do not use gasoline or other solvents.
Finally dry with dry cloth. Keep water heater dry. Do not use cleansers containing grinding agent (e.g. toothpaste), acids, chemical solvents (e.g. alcohol) or polishers to clean.
Internal Cleaning: To ensure high working efficiency, heating elements and tank liner of water heater shall be cleaned once in three years. Take care not to damage protection layer on heating elements and tank liner inner surface. According to different local water qualities and use habits, magnesium rod shall be periodically replaced. If maintenance is needed, please contact local service station.
FAQ
Phenomenon Confirmation items Remedy
No water
Only cold water but pointer light when heat
Only cold water and pointer not light when heat
No water supply or water pressure too low
Hot water access close
Check
Check and clear
Hot water access close Check and open
Adjust temperature of water Temperature not set to desired setting heating time limit and setting temperature not obtain
Defective heater
No power to heater
Uncontrollable thermostat
Keep heating
Contact with service department when are excluded
Check power socket
Contact with service department when are excluded
Heating pointer
always light
Setting water temperature not obtain uncontrollable thermostat
Keep heating
Contact with service department when are excluded
Unconstant flow and temperature of water
Unconstant water pressure
Temperature set too low
Insufficient hot water Excessive water pressure
Adjust the flux of outlet water or use with constant water pressure
Adjust setting water temperature
Adjust the flux of outlet water
Before Usage
Dear users,
Thanks for choosing Haier water heater product.
Haier products have good quality and excellent performance. To facilitate you to use the product, please read the manual and operate accordingly. Please retain it for future reference.
The international star service of Haier Group will always accompany you. No matter what kind of problems you meet in usage, please contact with the local after -sales service agent. We are at your service all the time. Thanks again for choosing Haier
Product.
The water heater you purchased may not full comply with the manual due to the improvement of product. We apologize for the inconvenience occurred therefrom.
Features
1 Safety:
High-quality heat proof stainless steel electric heating element, overtemperature protection; overpressure protection of tank; safe and reliable.
Safe Care patented design together with the function of monitoring and displaying of live ground wire has become a real safeguard for family safety.
2 Durability:
The shell adopts dusting anticorrosion treatment, handsome and durable enamel tank, with reliable quality and long operation life.
3 Convenience:
Adjustable heating temperature.Adjustable water temperature.
Adjusting range: water inlet temperature 75 .
4 Multiple usage:
Enclosed structure, capable of supplying water to multiple places like toilet, kitchen etc. Suitable for family, enterprises, service trades like beauty care on hot water supply
(not drinkable).
5 Nice molding, horizontal type wall-mounting design, saving space.
The water heater you purchased is the improved model of the series product. Please operate according to the user's manual.
2
Parameters
Rated voltage: 220V~,50Hz Dimension: (See to Figure 1)
Rated power: 1200W Weight: (See to Figure 1)
Rated pressure: 0.75MPa Volume: (See to Figure 1)
Waterproof grade: IPX4 Tap water pressure: no less than 0.05MPa
Dimensions
(Figure 1)
Front view a1 b1
D
Cutaway view d1
F
C
E
Bottom view e1
A B
C1
Model
FCD-JTHA30 (ET)
FCD-JTHA40ET
FCD-JTHA50 (ET)
Volume
30L
40L
50L
Net weight kg
15.1
16.5
18.5
FCD-JTHA60- (ET)
FCD-JTHA80- (ET)
60L
80L
20.5
26.6
Rated temperature
75 a1 b1 c1 d1 e1 f1 mm mm mm mm mm mm
569 366 100 192 347 200
75
75
688
694
391 100
438 100
220
220
353 200
400 200
75
75
795
991
437
440
100
100
305
521
400
400
200
200
A Hot water outlet
B Cold water inlet
C Heating element
D Enamel tank
E Wall-mounting
bracket
F Magnesium anode
rod
Remarks:the permitted error limit of above parameters is 10%.
Electric Circuit Diagram
MT BT
L:Brown wire
N:Blue wire
MT: High temperature limiter
BT: Thermostat
HL:Heating indicator
EH:Heating element
E:Yellow/green wire
L
N
E
HL
EH
E
3
Operation Instructions
For the first use after installation, due to there's no water within the tank, first the city water inlet valve and mixing valve must be opened. Close the mixing valve when water flows out continuously from the showerhead or other outlets (the tank is full). Check connections are free of water leakage, and insert the power plug.
Turn the knob to set your desired water heating temperature, which can be stepless changed between cold water inlet temperature and 75 . In heating mode, heating lamp is lighted on. Normally the knob shall be positioned at highest temperature. This machine has a thermostat function, which automatically switches off the water heater when temperature reaches the setting value, and switch on again when water temperature decreases to certain value.
City water pressure 0.75 MPa will cause much water flowing out from safety valve pressure relief vent. This is due to too high water pressure. Please ask after-sales service for correction.
Attentions in Operation
1.
To avoid causing machine troubles, do not connect power before tank is full of water.
2.
Adjust a suitable temperature before use, for water temperature above 50 may burn your skin.
3.
This product is closed water heater, which can supply hot water through pipe connection to several points like bathroom (bathtub, washbasin, showerhead) and kitchen.
4.
Heating adjustment can be made flexibly all year round adapting to climate changes. In long-term out-of-use or maintenance, you can close city water pipe valve, open mixing valve to hot water range, and move up safety valve handle to drain the tank. To avoid injury, before next use, it is suggested to first open hot water valve before switching on the water heater, exhausting gas possibly retained in the pipeline. In this case, no smoke or fire is permitted near the open valve. Carefully check and confirm all parts are in good condition.
5.
Provided hot water quantity can meet use demand, temperature setting shall be possibly low. It can minimize heat dissipation, high-temperature corrosion and sedimentation, ensuring a longer service life.
6.
Regularly ask servicemen to make safety inspection, remove sediment on heating elements, and check consumption of anode bar. Too much consumed anode bar shall be replaced.
Installation
The water may drip from the discharge pipe of the pressure relied device and that this pipe must be installed in a continuously downward direction and in a frost-free environment. Check safety valve once a month as follow: move the small handle of safety valve, if there's water flowing out, safety valve is normal; if there's no water flow, please contact local after-sales service station.
The pressure relief device is to be operated regularly to remove lime deposits and to verify that it is not blocked.
pressure release hole
(Figure 4)
Attentions in Installation
During installation, adequate space must be reserved for future maintenance and repair. If the water heater is installed within decoration boards, the right board shall be removable to facilitate removing the plastic cover during maintenance.
City water inlet pressure shall not be less than 0.05 MPa,Maximum pressure can not exceed 0.7MPa.
Electric water heater shall be installed indoors with ambient temperature above
0 . The pipes shall be collectively laid. Hot water outlet shall not be too far from use points. In case farer than 8 m, hot water pipe shall have a thermal insulation to minimize heat loss.
The mounting wall shall be firm and reliable to support twice the weight of water heater full of water. Non-load bearing walls or air brick walls must have corresponding protective measures like additional support, wall-through screws or back boards.
Electric water heater shall be located in a place easy for use, maintenance and with a floor drainer. In case the tank or pipes leak, nearby or lower facilities shall not be damaged. The installation location shall avoid being above toilet bowl, bathtub, washbasin or doorframe, where will cause a suppressed or unsafe feeling to users.
Power socket for water heater shall be in a dry place free of water splash. (splashproof box is preferred).
Do not confuse inlet and outlet water pipes. Safety valve shall be installed at designated position with no random modification.
Safety Precautions
22
0V
50
Hz
Check if the ammeter and the diameter of the wires are in accordance with the rated current of the water heater. If necessary please have it checked by experienced electrician.
The water heater adopts power supply of 220-240V ,
50/60Hz.
NO
¡
Be sure to use independent receptacle and earth it reliably.
The receptacle shall comply with the stipulation of
national standard.
Set the receptacle of the water heater at dry position away from water spraying. Do not insert a n d p u l l t h e p o w e r pl u g w i t h w e t h a n d s .
Ó Ã
ÚÏ
´Ô
¡
²
Ô
²
»¿
ÉÒ
Ô
Á
After installation, be sure to fill the heater completely with water before switching on the power in the first usage.
Children must take bath under the supervision of adult.
In opening and closing the water valve, do not point
the shower head to human body. Otherwise it may hurt by the spraying hot water.
C
Haier
In winter of cold area, if the heater is idle for a long period, please pull the handle of safety valve to discharge the water. Otherwise it may freeze inside the water heater and cause damages.
In case the power cord of the water heater is damaged, be sure to have it replaced by after service technicians with special cord offered by the manufacturer.
The product adopts the patent "Safe Care" technology of our company. As long as adopting civil power supply, even if the earthing wire is electrified by mistake, the "Safe Care" technology still can block the dangerous electricity, and ensure your personal safety. But if you find perceptible current, please pull off the power plug and contact local after service department for maintenance. Do not disassemble by yourself.
Description of the Symbols
Never do that
Be sure to act as per instructions
4
Setting Environment
Do not set it at place where is too cold and may freeze.
Do not set at outdoor places.
Do not use as floorstanding appliance.
Please mount it to firm and reliable wall.
Do not install to places without sewer.
In case connecting water heater with water drain hose, connect the drain hose to the inlet of the sewer to avoid polluting by splashing.
The original pipeline of the water heater is an organic part of "Safe Care". Do not remove it by yourself.
Otherwise we will not take responsibility for the injure and loss caused by the safety trouble occurred therefrom.
Description of the Symbols
Never do that
Be sure to act as per instructions
5
Installation
Installation must be made by installers of or designated by our company after-service department. The water heatershall be wall-mounted.
Before installation, make sure water heater rear wires are fit firmly. Determine an installation location. Make four holes 12mm, 65 mm deep in the wall with an impact drill according to installating dimension. Insert fixexpansion hooks and expansion bolts in corresponding wall holes. Lift the water heater. Insert wall rack onto the hooks and bolts. Fit flat washers, rear wires and nuts in turn onto the bolts (see Figure 2). Tighten the nuts and check them firm. Install accessories such as safety valve, drain hose as shown in Figure 3. Use sealing compound to prevent water leakage.
To facilitate installation and removal, it is suggested a G 1/2" movable nut is fitted at appropriate locations on inlet and outlet pipes respectively. Find water supply location.
Connect inlet pipe, outlet pipe and city water pipe respectively to the use point.
The hot water pipe shall not be too long to reduce the heat losses.
Please reserve some space in installation for the future maintenance.
Hot water outlet
Safety valve
Cold water inlet
Shower head
Hot water outlet valve
Cold water outlet valve
Mixing valve
(Figure 2) (Figure 3) for reference in installation only
Connection and use of safety valve:
The safety valve should be connected to the cold water inlet pipe. Please check carefully if the direction is correct after installation. The correct direction of installation is that the arrowhead on the safety valve should point to the water heater.
Please connect the drain hose to the safety valve. Connect one end of the hose to the safety valve vent and the other end to the sewage drain. The hose can be cut short or extended as necessary. The hose shall be installed as inclined downward.(see to
Figure 4)
6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project