Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. P [ TTSB URG HH ITEM 91200 Flame Design Bar/Counter Visit our website at: http://www.harborfreight.com REV 14e Email our technical support at: [email protected] When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright® 2014 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. AWARNING Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. Specifications Seat Dimensions 14-1/2" Diameter x 3-3/4" Thick Seat Height 28-1/4" Leg Floor Dimensions Leg Spread Foot Rest to Floor 11-1/2" Weight 16 Ib Maximum Weight Capacity 300 Ib IMPORTANT SAFETY INFORMATION Assembly Precautions — N 3. Assemble only according to these instructions. Improper assembly can create hazards. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. Keep assembly area clean and well lit. Use Precautions Keep bystanders out of the area during assembly. Do not assemble when tired or when under the influence of alcohol, drugs or medication. Weight capacity and other product capabilities apply to properly and completely assembled product only. — © > N Page 2 This product is not a toy. Do not allow children to play with or near this item. Use as intended only. Inspect before every use; do not use if parts are loose or damaged. Do not exceed weight capacity of 300 Ib. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. PITTSBURGH Ex For technical questions, please call 1-888-866-5797. Store idle equipment. When not in use, this product must be stored in a dry location to inhibit rust. Replacement parts and accessories. When servicing, use only identical replacement parts. WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.) The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Item 91200 Assembly Instructions Note: When assembling the leg/base section of the Stool, all of the bolts should have their heads facing outside, with all of the nuts on the inside of the frame. Note: The Stool should be assembled and used on a flat, level, dry surface. Refer to the Assembly Diagram during assembly. — Set the Upper Leg (1) over the Lower Leg (2) as shown in the Assembly Diagram below. When nested together properly, the top of the assembly will be flush. N Slide the Foot Rest (4) over the leg assembly and connect the three pieces with four Long Bolts (6). Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Note: The Long Bolts (6) should travel from the outside of the Foot Rest (4) to the inside of the Upper/Lower Legs (1, 2). 3. Secure the Bolts with four Washers (11) and Acorn Nuts (7) on the inside of the Stool. 4. Insert the four Medium Bolts (8) through the Swivel (9) plate, and into the leg section. Tighten all Bolts. 5. Place the Seat (5) cushion-side down on a flat surface that will not scratch the cushion. Place the Swivel (9) assembly on the bottom of the Seat, so the holes on the Swivel line up with the holes on the underside of the seat. 6. Use Short Bolts (10) to attach Swivel to Seat. Parts List and Diagram Part Description Qty 1 Upper Leg 1 2 Lower Leg 1 3 Feet 4 4 Footrest 1 5 Seat 1 6 |Long Bolt M6x45 4 7 Locknut (M6) 8 8 Medium Bolt M6x31 4 9 Swivel plate 1 10 |Short Bolt M6x12 4 11 ¡Washer* 8 *Item not shown. Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 91200 For technical questions, please call 1-888-866-5797. Page 3 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. PITTSBURGH xx 3491 Mission Oaks Blvd. - PO Box 6009 *« Camarillo, CA 93011 - 1-888-866-5797
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021