Pittsburgh Automotive Flame Design Bar/Counter Swivel Stool, 62202 Owner's manual

Pittsburgh Automotive Flame Design Bar/Counter Swivel Stool, 62202 Owner's manual
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Flame Design
Bar/Counter
Swivel
Stool
REV 14e
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Specifications
Seat Dimensions
14-1/2" Diameter
x 3-3/4" Thick
Seat Height
28-1/4"
Leg Floor Dimensions
20" 4-Way Leg Spread
Foot Rest to Floor
12-1/2"
Weight
11.45 lb
Maximum Weight Capacity
300 lb
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
6. Store idle equipment. When not in use, this product
must be stored in a dry location to inhibit rust.
2. Use as intended only.
7. Replacement parts and accessories. When
servicing, use only identical replacement parts.
3. Inspect before every use; do not use
if parts are loose or damaged.
4. Do not exceed weight capacity of 300 lb.
Be aware of dynamic loading! Sudden
load movement may briefly create excess
load causing product failure.
5. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Page 2
8. WARNING: This product contains di (2-ethylhexyl)
phthalate (DEHP), a chemical known to the State
of California to cause cancer and birth defects
or other reproductive harm. (California Health
& Safety Code § 25249.5, et seq.)
9. The warnings, cautions, and instructions discussed
in this instruction manual cannot cover all possible
conditions and situations that may occur. It must
be understood by the operator that common sense
and caution are factors which cannot be built into
this product, but must be supplied by the operator.
For technical questions, please call 1-888-866-5797.
Item 62202
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
Note: When assembling the leg/base section of the
Stool, all of the bolts should have their heads facing
outside, with all of the nuts on the inside of the frame.
Note: The Long Bolts (6) should travel
from the outside of the Foot Rest (4) to the
inside of the Upper/Lower Legs (1, 2).
Note: The Stool should be assembled and
used on a flat, level, dry surface. Refer to the
Assembly Diagram during assembly.
3. Secure the Bolts with Acorn Nuts (7)
on the inside of the Stool.
4. Insert the four Medium Bolts (8)
through the Swivel (9) plate, and into
the leg section. Tighten all Bolts.
1. Set the Upper Leg (1) over the Lower
Leg (2) as shown in the Assembly Diagram
below. When nested together properly,
the top of the assembly will be flush.
2. Slide the Foot Rest (4) over the leg assembly and
connect the three pieces with four Long Bolts (6).
5. Place the Seat (5) cushion-side down on a
flat surface that will not scratch the cushion.
Place the Swivel (9) assembly on the bottom
of the Seat, so the holes on the Swivel line up
with the holes on the underside of the seat.
6. Use Short Bolts (10) to attach Swivel to Seat.
Parts List and Diagram
Part
1
2
3
4
5
6
7
8
9
10
Description
Upper Leg
Lower Leg
Feet
Footrest
Seat
Long Bolt M6x45
Locknut (M6)
Medium Bolt M6x31
Swivel plate
Short Bolt M6x12
Qty
1
1
4
1
1
4
8
4
1
4
5
10
9
8
1
2
6
7
4
3
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Item 62202
Note: Some parts are listed and shown for
illustration purposes only, and are not available
individually as replacement parts.
For technical questions, please call 1-888-866-5797.
Page 3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement