HealthRider HRT12920 User's Manual

HealthRider HRT12920 User's Manual
Model No. HRT12920
Serial No.
Write the serial number in the space
above for future reference.
Serial Number Decal
USER'S MANUAL
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.– 6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
Visit our website at
www.healthrider.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
HealthRider is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppressor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 300 pounds. Never allow
more than one person on the treadmill at a time.
16. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug the power cord when the treadmill is not
in use.
9. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local HealthRider dealer or call 1-800-8063651 and order part number 146148.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
20. When using iFIT.com CD’s and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
23. Inspect and properly tighten all parts of the
treadmill every three months.
24. Never drop or insert any object into any opening.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
21. When using iFIT.com CD’s and videos, you
can manually override the speed and incline
settings at any time by pressing the speed and
incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
22. Always remove iFIT.com CD’s and videos
from your CD player or VCR when you are not
using them.
26. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If a decal is missing
or illegible, please call our Customer Service Department toll-free at 1-800-999-3756
to order a free replacement decal. Apply the decal in the location shown. Note: The
decals are not shown at actual size.
KEEP HANDS
AND FEET
AWAY FROM
THIS AREA
WHILE THE
TREADMILL IS
IN OPERATION.
4
BEFORE YOU BEGIN
Congratulations for purchasing the HealthRider® L600i
treadmill. The L600i treadmill offers an impressive
array of features to help you achieve your fitness goals
in the convenience of your home. From the advanced
console to the cushioned walking platform, the L600i
treadmill is designed to make each workout more effective and enjoyable. And when you’re not exercising,
the treadmill can be folded away, taking less than half
the floor space of conventional treadmills.
ing this manual, call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is HRT12920. The serial number can be found
on a decal attached to the treadmill (see the front
cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Book Holder
Fan
Water Bottle Holder*
Console
Handrail
Handgrip Pulse Sensor
Key/Clip
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
BACK
Cushioned Walking Platform
RIGHT SIDE
Rear Roller
Adjustment Bolts
*No water bottle is included
5
ASSEMBLY
Assembly requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires your own phillips screwdriver
cutters
, and adjustable wrench
, rubber mallet
, wire
.
1. For help identifying small parts, refer to the PART
IDENTIFICATION CHART on page 27.
1
114
Cut the plastic ties (not shown) from the sides of the
treadmill. With the help of a second person, carefully
raise the Uprights (65) until the Wheels (not shown) are
resting on the floor.
Hold the Book Plate (114) against the back of the
Console Base (117) and the Upright (65) as shown.
Attach the Book Plate with four 3/4” Silver Screws (101).
101
117
101
65
2. Insert one of the Handrail Extensions (76) into the square
post on the left Upright (65). Make sure that the notch
in the Handrail Extension is in the position shown.
Align the small holes in the Handrail Extension with the
holes in the post. If necessary, use a rubber mallet to fully
insert the Handrail Extension. Attach the Handrail
Extension with four Extension Screws (50).
2
114
128
Post
Identify the Left Foam Grip (62), which has a hole in the
right side. Slide the Left Foam Grip as far as possible
onto the Handrail Extension (76) and the post. (Note: It
may be helpful to apply soapy water to the Handrail
Extension.) Press two Plastic Fasteners (75) into the bottom of the Left Foam Grip and the Handrail Extension.
Note: It may be helpful to tap on the Plastic Fasteners with
a rubber mallet.
50
76
Hole
62
50
Notch
75
Attach the other Handrail Extension (not shown) and the
Right Foam Grip (not shown) to the post on the right
Upright (65) in the same way. Note: There is not a hole in
the side of the Right Foam Grip.
Press a Cup Holder (128) into the Book Plate (114). Press
the other Cup Holder (not shown) into the other side of the
Book Plate.
6
65
3. (Note: The parts shown in this step may be preassembled.)
With the help of a second person, raise the Frame (55) and
hold it. Insert the Left Frame Guide (68) into the left side of
the Frame. Remove the Lock Knob (67) from the Lock Pin
(72). Make sure that the Lock Pin Collar (70) and the Spring
(69) are on the Lock Pin. Insert the Lock Pin into the Frame
and the Left Frame Guide. Press the Latch Insert (5) onto
the Frame, with the Lock Pin in the center hole. Tighten the
Lock Knob onto the Lock Pin.
3
Hole
Have a second person hold the treadmill in the upright position. Place the U-base (20) against the base of the Uprights
(65) as shown. Make sure that the U-base is turned so
the Bumpers (98) are on the bottom. Finger tighten two
2” Bolts (26) and Base Washers (130) into the base of the
Uprights and the U-base. Attach the U-base with two 3”
Bolts (23) and two U-base Nuts (51) as shown. Tip the
treadmill forward if necessary. Tighten the two 2” Bolts.
68
69
62
51
26
130
51
26
23
65
130
98
20
98
23
1
1. Make sure that the power cord is unplugged. Remove the
indicated 3/4” Screws (40) from the Console Back (117).
Remove the Console Back.
117
40
2. Connect the Short Jumper Wire (A) to the wire on the
Receiver (B). Connect the other end of the Short Jumper
Wire to the PULSE jack on the back of the Console (80).
Turn the Receiver (B) so the cylinder is on the side
shown, and hold the Receiver against the back of the
Console (80). Attach the Receiver with the two Small
Screws (C) included with the receiver.
7
40
2
80
Cylinder
B
A
C
Make sure that no wires are pinched. See step 1.
Reattach the Console Back (117) with the 3/4” Screws (40).
You may discard the other wires included with the receiver.
67
4
5. Make sure that all parts are properly tightened before
you use the treadmill. Place a mat beneath the treadmill to protect the floor. For your benefit, familiarize
yourself with the information on pages 23 and 24.
If you purchase the optional chest pulse sensor (see page
20), follow the steps below to install the receiver and the
short jumper wire included with the chest pulse sensor.
129
5
72
Align the Lock Pin (72) with the hole in the Left Foam Grip
(62) by sliding the Left Frame Guide (68) up or down.
Make sure that the Lock Pin can be inserted fully into the
hole. Hold the Left Frame Guide in place as you tighten
two 1/2” Screws (129) into the Latch Insert and the Left
Frame Guide. Note: It may be necessary to pull the Lock
Knob (67) to access and tighten the Screws.
4. Put the treadmill in the storage position (see HOW TO
FOLD THE TREADMILL FOR STORAGE on page 21).
55
70
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local HealthRider dealer or call 1-800-806-3651
and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Key
Clip
FEATURES OF THE CONSOLE
CD programs automatically control the speed and incline of the treadmill as a personal trainer guides you
through every step of your workout. High-energy music
provides added motivation. Each CD features two programs designed by certified personal trainers.
The treadmill console offers an impressive array of
features designed to make your workouts more effective.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor.
Note: See page 20 for information about an optional
chest pulse sensor.
In addition, you can connect the treadmill to your VCR
and TV and play iFIT.com video programs (videocassettes are available separately). Video programs offer
the same benefits as iFIT.com CD programs, but add
the excitement of working out with a class and an
instructor—the hottest new trend at health clubs.
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
details.
In addition, the console offers four preset workout programs. Each program automatically controls the speed
and incline of the treadmill as it guides you through an
effective workout. Two heart rate programs are also offered. Each program automatically adjusts the speed
and incline of the treadmill to keep your heart rate within
a preset range while you exercise.
To purchase iFIT.com CD’s or videocassettes, call tollfree 1-800-735-0768.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer right in your home. Using the included
audio cable, you can connect the treadmill to your
home stereo, portable stereo, or computer and play
special iFIT.com CD programs (one iFIT.com CD is included; other CD’s are available separately). IFIT.com
To use the manual mode of the console, follow the
steps beginning on page 10. To use preset workout
programs, see page 12. To use heart rate programs,
see page 13. To use iFIT.com CD or video
programs, see page 17. To use iFIT.com programs
directly from our Web site, see page 19.
9
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 8).
2
Locate the circuit
breaker near the
power cord. Make
sure the breaker is in
the reset position.
3
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. To change the speed setting quickly, press
the OneTouch Speed buttons. Note: The console
can display speed and distance in either miles
or kilometers. For simplicity, all instructions in
this section refer to miles.
Reset
Position
To stop the walking belt, press the Stop button.
The Time/Segment Time/Pace display will begin
to flash. To restart the walking belt, press the Start
button or the Speed ▲ button.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 9)
and slide the clip onto the waistband of your
clothes. Next, route the cord attached to the clip
under the handgrip pulse sensor, and insert the
key into the console. After a moment, the displays
and various indicators will light. Test the clip by
carefully taking a few steps backward until the
key is pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 24).
4
To change the incline of
the treadmill, press the
Incline buttons. Each time
a button is pressed, the
incline will change by
0.5%. Note: After the buttons are pressed, it may take a moment for the
treadmill to reach the selected incline setting.
HOW TO USE THE MANUAL MODE
1
5
Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
2
Follow your progress with the LED matrix and
the displays.
The LED matrix—When
the manual mode or the
iFIT.com mode is selected, the LED matrix
will show a track representing 1/4 mile. As you
exercise, the indicators
around the track will light, one at a time, until you
have completed 1/4 mile. A new lap will then begin.
Select the manual mode.
When the key is inserted, the manual
mode will be selected
and the Manual Control
indicator will light. If a
program has been
selected, press the Program Select button repeatedly to reselect the manual mode.
3
Change the incline of the treadmill as desired.
Time/Segment Time/
Pace display—When the
manual mode or the
iFIT.com mode is selected, this display will
show the elapsed time
and your current pace (pace is measured in minutes per mile). The display will change from one
number to the other every few seconds. When a
preset program or a heart rate program is selected, the display will show the time remaining in
the program, the time remaining in the current segment of the program, and your current pace.
Press the Start button or the Speed ▲ button to
start the walking belt.
A moment after the button is pressed, the
walking belt will begin to
move at 1 mph. Hold
the handrails and begin
walking. As you exercise, change the speed of the walking belt as desired by pressing the Speed ▼ and ▲ buttons.
10
Pulse/Calories/Fat
Calories display—This
display shows the approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 25). The display will
change from one number to the other every few
seconds. The display will also show your heart
rate when you use the handgrip pulse sensor or
the optional chest pulse sensor.
6
Measure your heart rate if desired.
You can measure your heart rate using either the
handgrip pulse sensor or the optional chest pulse
sensor.
To use the
Contacts
handgrip pulse
sensor, first
make sure that
your hands are
clean. Next,
stand on the
foot rails and
place your
hands on the
metal contacts on the handgrip pulse sensor. Your
palms should be resting on the upper contacts
and your fingertips should be touching the lower
contacts. Avoid moving your hands. When your
pulse is detected, two dashes (– –) will appear in
the Pulse/Calories/Fat Calories display, and then
your heart rate will be shown. For the most accurate heart rate reading, continue to hold the
contacts for about 15 seconds.
Distance/Incline/Laps
display—This display
shows the distance that
you have walked, the incline level of the treadmill, and the number of
1/4-mile laps you have completed. The display will
change from one number to the next every few
seconds. Note: Each time the incline changes, the
display will show the incline setting for several
seconds.
Speed display—This
display shows the speed
of the walking belt.
7
Turn on the fans if desired.
To use the fans, press the Low or High button. To
turn off the fans, press the Off button. Note: Any
time that the walking belt is stopped for a few minutes, the fans will automatically turn off.
Note: When the Km/H indicator is lit, the console
will display speed and
distance in kilometers;
when the Km/H indicator
is not lit, the console will
display speed and distance in miles. To change
the unit of measurement, first hold down the Stop
button while inserting the key into the console. An
“E” for English miles or an “M” for metric kilometers
will appear in the Speed display. Press the Speed
▲ button to change the unit of measurement.
When the desired unit of measurement is selected,
remove the key and then reinsert it.
8
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is
removed, the console is in the “demo” mode.
See page 20 and turn off the demo mode.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
When you are finished using the treadmill, unplug
the power cord.
11
The speed setting for
Current Segment
the first segment is
shown in the flashing
Current Segment column of the LED matrix.
(The incline settings are
not shown in the matrix.)
The speed settings for
the next five segments
are shown in the columns to the right.
HOW TO USE PRESET WORKOUT PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
2
Select one of the preset workout programs.
When the key is inserted, the manual
mode will be selected.
To select a preset
workout program, press
the Program Select button repeatedly until one
of the Walk or Jog indicators lights.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, if the speed
and/or incline of the treadmill is about to change,
the Speed display and/or the Distance/Incline/
Laps display will flash to alert you. When the first
segment is completed, all speed settings will move
one column to the left. The speed setting for the
second segment will then be shown in the flashing
Current Segment column and the treadmill will automatically adjust to the speed and incline settings
for the second segment. Note: If all of the indicators in the Current Segment column are lit after the
speed settings have moved to the left, the speed
settings will move downward so that only the highest indicators appear in the LED matrix. If some of
the indicators in the Current Segment column are
not lit when the speed settings move to the left
again, the speed settings will move back up.
When a preset workout program is selected, the
Distance/Incline/Laps display will flash the maximum incline setting of the program, and the
Speed display will flash the maximum speed setting, for six seconds. The Time/Segment Time/
Pace display will show how long the program will
last.
The LED matrix will
show the first five
speed settings of the
program. The profiles
on the right side of the
LED matrix show how
the speed and incline
of the treadmill will change during the programs.
3
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then stop.
Press the Start button or the Speed ▲ button to
start the program.
If the speed or incline setting is too high or too low
during the program, you can manually override
the setting by pressing the Speed or Incline buttons. Every few times a Speed button is pressed,
an additional indicator will light or darken in the
Current Segment column. (If any of the columns
to the right of the Current Segment column have
the same number of lit indicators as the Current
Segment column, an additional indicator may light
or darken in those columns as well.) Note: If you
manually override the speed or incline setting,
when the next segment begins, the treadmill
will automatically adjust to the speed and incline settings for the next segment.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths. (The Time/Segment
Time/Pace display will show both the time remaining in the program and the time remaining in the
current segment of the program.) One speed setting and one incline setting are programmed for
each segment. (The same speed and/or incline
setting may be programmed for consecutive segments.)
12
To stop the program temporarily, press the Stop
button. The Time/Segment Time/Pace display will
begin to flash. To restart the program, press the
Start button or the Speed ▲ button. To end the
program, press the Stop button, remove the key,
and then reinsert the key.
4
HOW TO USE HEART RATE PROGRAMS
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
Follow your progress with the displays.
See step 5 on page 10.
5
Measure your heart rate if desired.
Follow the steps below to use a heart rate program.
Note: You must wear the optional chest pulse sensor (see page 20) to use a heart rate program.
See step 6 on page 11.
6
Turn on the fans if desired.
See step 7 on page 11.
7
1
Put on the optional chest pulse sensor.
Refer to the instructions included with the optional
chest pulse sensor.
When the program is finished, remove the key
from the console.
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place.Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 20 and turn off the
demo mode.
2
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
3
Select a heart rate program.
When the key is inserted, the manual
mode will be selected.
To select a heart rate
program, press the
Program Select button
repeatedly until one of the heart rate program indicators lights.
When you are finished using the treadmill, unplug
the power cord.
The two profiles on the left side of the LED matrix
show how the target heart rate will change during
the programs. During heart rate program 1, your
heart rate will reach approximately 85% of your
estimated maximum heart rate; during heart rate
program 2, your heart rate will reach approximately 80% of your estimated maximum heart
rate. Note: Your estimated maximum heart rate is
determined by subtracting your age from 220. For
example, if you are 30 years old, your estimated
maximum heart rate is 190 beats per minute
(220 – 30 = 190).
13
4
During heart rate programs, the LED matrix
will show a graphic that
represents your heart
rate. Each time a heartbeat is detected, an additional peak will appear.
the treadmill will automatically increase or decrease to bring your heart rate closer to the target
heart rate setting. If the speed reaches the maximum speed setting of the program (see step 4 at
the left) and your heart rate is still too far below
the current target heart rate setting, the incline of
the treadmill will also increase to bring your heart
rate closer to the target heart rate setting.
Enter your age and a maximum speed setting
for the program.
During the last three seconds of each segment, a
series of tones will sound and the Distance/
Incline/Laps display and the Speed display will
flash.
When a heart rate program is selected, the
word “AGE” and the
current age setting will
flash in the Pulse/
Calories/Fat Calories
display. If you have already entered your age,
simply press the Enter button. If you have not entered your age, press the ▲ and ▼ buttons beside
the Enter button to enter your age. Then, press
the Enter button.
The program will continue until no time remains in
the program. The walking belt will then slow to a
stop.
If the speed or incline setting is too high or too low
during the program, you can adjust the setting
with the Speed or Incline buttons. However, each
time the console compares your heart rate to the
current target heart rate setting, the speed and/or
incline of the treadmill may automatically change
to bring your heart rate closer to the target heart
rate setting.
After you have entered
your age, the letters
“SPd” and the maximum speed setting of
the program will flash in
the Pulse/Calories/Fat
Calories display. If desired, press the ▲ and ▼ buttons beside the Enter button to adjust the maximum speed setting. When the desired setting is
shown, press the Enter button.
5
If your pulse is not detected during the program,
the letters “PLS” will flash in the Pulse/Calories/
Fat Calories display and the speed and incline of
the treadmill may automatically decrease until
your pulse is detected. If this occurs, refer to the
instructions included with the optional chest pulse
sensor.
Press the Start button or the Speed ▲ button to
start the program.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
6
Each heart rate program is divided into several time
segments of different lengths. (The Time/Segment
Time/Pace display will show both the time remaining in the program and the time remaining in the
current segment of the program.) One target heart
rate setting is programmed for each segment.
Follow your progress with the displays.
See step 5 on page 10.
7
Turn on the fans if desired.
See step 7 on page 11.
8
During each segment, the console will regularly
compare your heart rate to the current target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting, the speed of
When the program is finished, remove the key
from the console.
See step 7 on page 13.
14
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CD’s, the treadmill must be connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
15 and 16 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 17 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home computer. See page 16 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
LEFT
Audio
Cable
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
Adapter
PHONES
B
Headphones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
Audio
Cable
3.5mm
Y-adapter
PHONES
Audio
Cable
Headphones
3.5mm
Y-adapter
Headphones
15
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B
PHONES
CD
Audio
Cable
VCR
Amp
3.5mm
Y-adapter
LINE OUT
Headphones/Speakers
RCA Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
16
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
To use iFIT.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
15. Note: To purchase iFIT.com CD’s or iFIT.com
videocassettes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
1
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
AUDIO OUT
RIGHT
LEFT
2
Audio
Cable
Adapter
When the key is inserted, the manual
mode will be selected.
To use iFIT.com CD’s or
videocassettes, press
the Program Select button repeatedly until the iFIT.com indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
3
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com videocassette, insert the videocassette into your VCR.
4
B
Press the PLAY button on your CD player or
VCR.
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time/Pace
display is flashing, press the Start button or the
Speed ▲ button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time/Pace display is flashing.
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
RCA Y-adapter
Audio
Cable
Select the iFIT.com mode.
Adapter
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
Wire removed from
AUDIO OUT jack
17
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time/Pace display will begin to flash. To restart
the program, press the Start button or the Speed
▲ button. After a moment, the walking belt will
begin to move at 1 mph. When the next “chirp”
is heard, the speed and incline will change to
the next settings of the CD or video program.
5
Follow your progress with the LED track and
the displays.
See step 5 on page 10.
6
Measure your heart rate if desired.
Refer to step 6 on page 11.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment
Time/Pace display will begin to flash. Note: To
use another CD or video program, press the Stop
button or remove the key and go to step 1 on
page 17.
7
Turn on the fans if desired.
See step 7 on page 11.
8
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
When the program is completed, remove the
key.
See step 7 on page 13.
• Make sure that the iFIT.com indicator is lit and
that the Time/Segment Time/Pace display is
not flashing. If the Time/Segment Time/Pace
display is flashing, press the Start button or
the Speed ▲ button on the console.
CAUTION: Always remove iFIT.com CD’s and
videocassettes from your CD player or VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
18
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Our Web site at www.iFIT.com allows you to access
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon to
be available. See www.iFIT.com for details.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system requirements are found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
1
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time/Pace display will begin to flash. To restart
the program, press the Start button or the Speed
▲ button. After a moment, the walking belt will
begin to move at 1 mph. When the next “chirp”
is heard, the speed and incline will change to
the next settings of the program.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
When the key is inserted, the manual
mode will be selected.
To use a program from
our Web site, press the
Program Select button
repeatedly until the iFIT.com indicator lights.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop and the Time/Segment Time/Pace display
will begin to flash. Note: To use another program,
press the Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time/Pace display is not
flashing. In addition, make sure that the audio
cable is properly connected, that it is fully
plugged in, and that it is not wrapped around a
power cord.
8
Read and follow the on-line instructions for using a
program.
6
See step 5 on page 10.
9
Follow the on-line instructions to start the
program.
When the program has ended, remove the key.
See step 7 on page 13.
When you start the program, an on-screen countdown will begin.
7
Follow your progress with the LED track and
the displays.
Return to the treadmill and stand on the foot
pads. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
19
THE INFORMATION MODE/DEMO MODE
mode. This mode is intended to be used only when a
treadmill is displayed in a store. When the console is in
the demo mode, the power cord can be plugged in, the
key can be removed from the console, and the displays
and indicators on the console will automatically light in
a preset sequence; the buttons on the console will not
operate. If a “d” appears in the Pulse/Calories/Fat
Calories display when the information mode is selected, press the Speed ▼ button so the display is
blank.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
To exit the information mode, remove the key from the
console.
THE OPTIONAL CHEST PULSE SENSOR
The Time/Segment Time/
Pace display will show the
total number of hours the
treadmill has been used.
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor provides
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, call toll-free 1-800734-2377.
The Distance/Incline/Laps
display will show the total
number of miles (or kilometers) that the walking belt
has moved.
An “E” for english miles or
an “M” for metric kilometers
will appear in the Speed display. Press the Speed ▲ button to change the unit of
measurement.
IMPORTANT: The Pulse/
Calories/Fat Calories display should be blank. If a
“d” appears in the display,
the console is in the “demo”
20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Hold the treadmill firmly with your left hand. Using your
right hand, pull the lock knob to the right and hold it.
Raise the treadmill until the pin on the lock knob is
aligned with the hole in the left foam grip. Then, release
the lock knob. Make sure that the lock knob is fully released so that the pin is fully inserted into the hole in
the left foam grip.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
Foam
Grip
Lock
Knob
Foam
Grip
Pin
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the locking pin is inserted into the left handrail.
Lock
Knob
Pin
Book
Holder
1. Hold the handrails as shown and place one foot against
the hood only in the location shown. Do not hold or
push on the book holder.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Hood
3. Place one foot on the hood and carefully lower the treadmill until it is resting in the storage position.
21
Base
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill firmly with your left hand. Pull the lock
knob to the right. Pivot the treadmill down until the pin on
the lock knob is below the foam grip. Slowly release the
lock knob.
Pin
Lock
Knob
Foam
Grip
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight.
22
TROUBLESHOOTING
Most treadmill problems can be solved by following the instructions below. If further assistance is
needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM
SOLUTION
1. The power does not
turn on
a. Make sure that the power cord is plugged into a surge suppressor, and that the
surge suppressor is plugged into a properly grounded outlet (see page 8). Use
only a single-outlet surge suppressor that meets all of the specifications described
on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
c
Tripped
2. The power turns off
during use
Reset
a. Check the circuit breaker located on the treadmill frame near the power cord (see
1. c. above). If the circuit breaker has tripped, wait for five minutes and then press
the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
3. The walking belt
slows when walked
on
a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadb
3–4”
mill performance may decrease and the
walking belt may be permanently damaged. Remove the key and UNPLUG THE
POWER CORD. Using the included allen
wrench, turn both rear roller adjustment
bolts counterclockwise 1/4 of a turn. When
the walking belt is properly tightened, you
should be able to lift the edges of the
Rear Roller Adjustment Bolts
walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking
belt centered. Plug in the power cord, insert the key and run the treadmill for a few
minutes. Repeat until the walking belt is properly tightened.
23
PROBLEM
SOLUTION
4. The walking belt is
off-center or slips
when walked on
a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER
CORD. If the walking belt has shifted to
the left, use the allen wrench to turn the
left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn.
Be careful not to overtighten the walking
belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on,
b
first remove the key and UNPLUG THE
POWER CORD. Using the allen wrench,
turn both rear roller bolts clockwise 1/4 of a
turn. When the walking belt is correctly
tightened, you should be able to lift each
side of the walking belt 3 to 4 inches off the
walking platform. Be careful to keep the
walking belt centered. Plug in the power
cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
5. The displays of the
console do not function properly
a. Remove the key from the console and UNa
PLUG THE POWER CORD. Next, remove
1/8”
the screws from the hood and carefully re11
44
move the hood. Locate the Reed Switch
12
17
(17) and the Magnet (12) on the left side of
the Pulley (11). Turn the Pulley until the
Top
Magnet is aligned with the Reed Switch.
View
Make sure that the gap between the
Magnet and the Reed Switch is about
1/8”. If necessary, loosen the indicated
Screw (44) and move the Reed Switch slightly. Retighten the Screw. Re-attach the
hood and run the treadmill for a few minutes to check for a correct speed reading.
24
EXERCISE GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
handgrip pulse sensor. If your heart rate is too high or
too low, adjust the speed or incline of the treadmill.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
25
PART LIST—Model No. HRT12920
R1202C
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
2
4
1
4
1
1
4
1
2
1
1
1
7
2
2
1
1
1
2
1
1
1
2
1
1
3
2
1
2
1
1
2
2
4
1
2
1
1
1
14
1
2
14
20
1
1
1
1
1
8
2
7
2
1
1
Description
Key No. Qty.
Foot Rail
Console Cover Screw
Audio Wire
Isolator
Latch Insert
Walking Platform
Walking Platform Screw
Walking Belt
Frame Pivot Bolt
IFIT.com CD
Front Roller/Pulley
Magnet
Front Roller Nut/Front Wheel Nut
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
Lift Frame
Foot Rail Insert
U-base
Front Roller Bolt
Motor Belt
3“ Bolt
Motor
Transformer
2” Bolt
Hood Bracket
Ground Wire
Motor Washer
Right Rear Endcap
Lift Motor Bolt
Motor Bolt
U-base Nut
Plastic Stand-off
Power Supply
Caution Decal
Controller
Electronics Bracket
Motor Hood
3/4” Screw
Motor Belly Pan
Belt Guide
3/4” Tek Screw
Electronics Screw
Left Front Endcap
Right Front Endcap
Left Rear Foot
Right Rear Foot
Console Ground Wire
Extension Screw
U-base Nut
Roller Adj. Washer
Rear Roller Adjustment Bolt
Left Rear Endcap
Frame
56
57
58
59*
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
26
1
2
1
1
1
1
1
1
1
1
6
1
1
1
1
1
1
1
1
4
2
2
2
1
1
1
2
1
8
1
1
2
2
1
1
1
1
8
1
2
2
5
6
1
1
4
1
1
2
1
1
1
1
1
1
Description
Allen Wrench
Rear Platform Screw
Rear Roller
Idler Assembly
Audio Wire Nut
Pulse Bar
Left Foam Grip
Idler Arm
Idler Spring
Upright
Pulse Bar Screw
Lock Knob
Left Frame Guide
Lock Knob Spring
Lock Pin Collar
Pin Clip
Lock Pin
Right Frame Guide
Latch Assembly
Plastic Fastener
Handrail Extension
Front Wheel
Wheel Bolt
Pulley Nut
Console
Console Cover
Fan
Key/Clip
Belly Pan Screw/Hood Screw
Upright Wire Harness
Shock
Round Upright Endcap
Upright Endcap
Filter Wire
Latch Warning Decal
Incline Motor
Motor Controller Wire
Fan Screw
Tie Holder Screw
Tie Holder
Tie
8” Cable Tie
Bumper
Idler Arm Bolt
Circuit Breaker
3/4” Silver Screw
Power Cord
Power Cord Grommet
Wheel Spacer
Incline Motor Shield
Jack
iFIT.com Audio Cable
Grommet
Pulley Washer
Idler Pulley
Key No. Qty.
111
112
113
114
115
116
117
118*
119
120
121
122
123
124
1
2
2
1
1
1
1
1
1
1
2
1
1
1
Description
Key No. Qty.
Pulley Spacer
Shield Screw
Static Decal
Book Plate
Idler Pulley Bolt
Right Foam Grip
Console Base
Latch Assembly
Right Fan Cover
Left Fan Cover
Motor Bushing
Idler Arm Nylon Washer
Hand Pulse Wire
Incline Bracket
125
126
127
128
129
130
#
#
#
#
#
1
2
1
2
2
2
1
1
1
1
1
Description
Incline Motor Bolt (Bottom)
Hood Mounting Screw
Motor Isolator Plate
Cup Holder
1/2” Screw
Base Washer
12” Green Wire, F/Ring
8” Green Wire, F/Ring
10” White Wire, 2 F
4” Blue Wire, 2 F
User’s Manual
* Includes all parts shown in the box
# These parts are not illustrated
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (HRT12920)
• The NAME of the product (HealthRider® L600i treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on pages 26 and 27)
PART IDENTIFICATION CHART
Use the chart below to identify small parts during assembly.
3/4” Silver Screw
(101)–4
Extension Screw
(50)–8
1/2” Screw
(129)–2
Base Washer (130)–2
2” Bolt (26)–4
3” Bolt (23)–2
U-Base Nut (51)–2
27
Plastic Fastener
(75)–4
LIMITED WARRANTY
WHAT IS COVERED—The entire HealthRider® L600i treadmill (“Product”) is warranted to be free of all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), extends a lifetime warranty on the frame. The
motor is covered for three years after the date of purchase. The belt and deck are covered for two years after the date
of purchase. All mechanical components are covered for two years after the date of purchase. All electrical components
are covered for two years after the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes or to products used as store display modules.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-800-999-3756 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 190939 R1202C
Printed in USA © 2002 ICON Health & Fitness, Inc.
53
52
72
40
54
118*
71
69
70
67
74*
52
43
47
55
57
56
52
5
53
68
90
40
4
43
129
30
19
8
48
1
To identify the parts shown on this
EXPLODED DRAWING, refer to the
PART LIST on pages 26 and 27.
58
1
7
52
43
6
42
4
40
44
28
57
43
40
45
9
7
40
12
99
73
110
111
7
115
59*
11
109
63
19
4
43
13
7
15 14
79
122
13
64
17
40
27
84
22
42
40
46
84
44
16
18
84
4
43
9
41
127
24
29
13
40
126
15
13 31
32
14
21
52
29
121
32
113 60
38
37
84
100
27
84
44
3
40
84
34
44
102
25
103
39
44
35
89
126
EXPLODED DRAWING—Model No. HRT12920
R1202C
23
43
98
43
20
98
62
75
23
88
13
43
36
76
87
91
65
50
124
98
66
125
66
50
112
105
51
130
26 104
78
77
98
43
130
26
98
43
13
101
123
116
75
61
85
108
51
76
66
44
86
88
50
36
43
40
98
104
13
101
120
50
80
77
87
2
78
81
40
40
44
49
113
40
40
128
117
106
40
93
82
40
40
119
92
40
93
107
83
114
97
96
95
94
10
128
EXPLODED DRAWING—Model No. HRT12920
R1202C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement