HealthRider HRTL07120 User's Manual

HealthRider HRTL07120 User's Manual
Model No. HRTL07120
Serial No.
Write the serial number in the space
above for future reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.– 6 p.m. MST
USER'S
MANUAL
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
Visit our website at
www.healthrider.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
HealthRider is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppressor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 250 pounds. Never allow
more than one person on the treadmill at a time.
16. The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the location of the on/off switch.)
9. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 24.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local HealthRider dealer or call 1-800806-3651 and order part number 146148.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
20. When using iFIT.com CD’s and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
23. Inspect and properly tighten all parts of the
treadmill every three months.
24. Never drop or insert any object into any opening.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
21. When using iFIT.com CD’s and videos, you
can manually override the speed and incline
settings at any time by pressing the speed and
incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
22. Always remove iFIT.com CD’s and videos
from your CD player or VCR when you are not
using them.
26. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If a decal is missing,
or if it is not legible, please call our Customer Service Department toll-free at
1-800-999-3756 to order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
BEFORE YOU BEGIN
Congratulations for purchasing the HealthRider® R60
treadmill. The R60 treadmill offers an impressive array
of features to help you achieve your fitness goals in
the convenience of your home. From the advanced
console to the cushioned walking platform, the R60
treadmill is designed to make each workout more effective and enjoyable. And when you’re not exercising,
the treadmill can be folded away, taking less than half
the floor space of conventional treadmills.
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number is HRTL07120. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Book Holder
Fans
Water Bottle Holder*
Console
Handrail
Handgrip Pulse Sensor
Key/Clip
On/Off Switch
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Cushioned Walking Platform
RIGHT SIDE
BACK
Rear Roller
Adjustment Bolts
*No water bottle is included
5
ASSEMBLY
Assembly requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires your own phillips screwdriver
cutters
.
, rubber mallet
1. Cut the plastic ties (not shown) from the sides of the
treadmill. With the help of a second person, carefully
raise the Uprights (65) until the Wheels (not shown) are
resting on the floor.
1
114
Hold the Book Plate (114) against the back of the
Console Base (117) and the Upright (65) with the “V”
shape of the Book Plate positioned as shown. Attach the
Book Plate with four 3/4” Screws (40).
and wire
“V”
40
40
117
65
40
2. Insert one of the Handrail Extensions (76) into the post on
the left side of the Upright (65). Make sure that the
notch in the Handrail Extension is in the position
shown. Align the holes in the Handrail Extension with the
holes in the post. If necessary, use a rubber mallet to fully
insert the Handrail Extension. Attach the Handrail
Extension to the post with four Extension Screws (131).
2
114
128
Post
Identify the Left Foam Grip (62), which has a hole in the
right side. Slide the Left Foam Grip as far as possible
onto the Handrail Extension (76) and the post. (Note: It
may be helpful to apply soapy water to the Handrail
Extension.) Press two Plastic Fasteners (75) into the bottom of the Left Foam Grip and the Handrail Extension.
131
76
Hole
62
Notch
Attach the other Handrail Extension and the Right Foam
Grip (not shown) to the post on the right side of the Upright
(65) in the same way. Note: There is not a hole in the side
of the Right Foam Grip.
Identify the Left Cup Holder (128); the lower edge is narrower on the left side, as shown. Press the Left Cup Holder
into the Book Plate (114). Press the Right Cup Holder (not
shown) into the other side of the Book Plate.
6
65
131
75
131
3. With the help of a second person, raise the Frame (55).
Hold the Latch Housing (68) and the Latch Housing Cover
(5) against the sides of the Frame (55) as shown. Loosely
screw the two 1/2” Screws (132) into the Latch Housing
Cover and the Latch Housing as shown. Do not tighten
the Screws yet.
Remove the Lock Knob (67) from the Lock Pin (72). Make
sure that the Lock Pin Collars (70) and the Spring (69) are
on the Lock Pin. The Lock Pin Collars should be on each
side of the Spring. Insert the Lock Pin into the Latch
Housing (68), and tighten the Lock Knob onto it.
Align the Lock Pin (72) with the hole in the Left Foam Grip
(62) by sliding the Latch Housing (68) up or down. Make
sure that the Lock Pin can be inserted fully into the hole.
Hold the Latch Housing in place as you tighten two 3/4”
Screws (40) in the Latch Housing and the Frame (55).
Tighten the 1/2” Screws (132). Note: It may be necessary
to pull on the Lock Knob (67) to access and tighten the
Screws.
3
67
Hole
5
132
62
68
Small
Holes
40
70 69
69
72
40
55
40
132
4. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with
the TROUBLESHOOTING section on pages 26 and 27.
7
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than necessary, draining the battery prematurely.
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset drawing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE SENSOR TROUBLESHOOTING
Sensor Unit
Sensor
Unit
Buckle
The instructions on the following pages explain
how the chest pulse sensor is used with the console. If the chest pulse sensor does not function
properly, try the steps below.
Next, wrap the
chest pulse sensor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse
sensor does not function when positioned as described, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
• As you walk or run on the treadmill, position yourself near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens solution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contractions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
• The CR2032 battery may need to be replaced (see
page 27).
8
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local HealthRider dealer or call 1-800-806-3651
and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
9
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Key
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effective.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor or
the chest pulse sensor.
In addition, the console offers six preset workout programs. Each program automatically controls the speed
and incline of the treadmill as it guides you through an
effective workout. Two pulse programs are also offered.
Each program automatically adjusts the speed and incline of the treadmill to keep your heart rate within a preset range while you exercise.
The console even allows you to create your own workout programs and save them in memory for future use.
The console also features new iFIT.com interactive
technology. IFIT.com technology is like having a personal trainer right in your home. Using the included
audio cable, you can connect the treadmill to your
home stereo, portable stereo, or computer and play
special iFIT.com CD programs (2 iFIT.com CD’s are in-
Clip
cluded). IFIT.com CD programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. Each
CD features two programs designed by certified personal trainers.
In addition, you can connect the treadmill to your VCR
and TV and play iFIT.com video programs (videocassettes are available separately). Video programs offer
the same benefits as iFIT.com CD programs, but add
the excitement of working out with a class and an
instructor—the hottest new trend at health clubs.
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
details.
To purchase iFIT.com CD’s or videocassettes, call tollfree 1-800-735-0768.
To use the manual mode of the console, follow the
steps beginning on page 11. To use preset programs,
see page 13. To use heart rate programs, see page
14. To create and use custom programs, see pages
16 and 17. To use iFIT.com CD or video programs,
see page 20. To use iFIT.com programs directly
from our Web site, see page 22.
10
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 9).
2
Locate the on/off
switch near the power
cord. Move the on/off
switch to the on position.
3
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. To change the speed setting quickly, press
the OneTouch Speed buttons. Note: The console
can display speed and distance in either miles
or kilometers. For simplicity, all instructions in
this section refer to miles.
On
Position
To stop the walking belt, press the Stop button.
The Time/Segment Time/Pace display will begin
to flash. To restart the walking belt, press the Start
button or the Speed ▲ button.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 10)
and slide the clip onto the waistband of your
clothes. Next, route the cord attached to the clip
under the handgrip pulse sensor, and insert the
key into the console. After a moment, the displays
and various indicators will light. Test the clip by
carefully taking a few steps backward until the
key is pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 27).
4
To change the incline of
the treadmill, press the
Incline buttons. Each time
a button is pressed, the
incline will change by
0.5%. Note: After the buttons are pressed, it may take a moment for the
treadmill to reach the selected incline setting.
HOW TO USE THE MANUAL MODE
1
5
Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
2
Follow your progress with the LED matrix and
the displays.
The LED matrix—When
the manual mode or the
iFIT.com mode is selected, the LED matrix
will show a track representing 1/4 mile. As you
exercise, the indicators
around the track will light in sequence until you
have completed 1/4 mile. A new lap will then begin.
Select the manual mode.
When the key is inserted, the manual
mode will be selected
and the Manual Control
indicator will light. If a
program has been
selected, press the Program Select button repeatedly to reselect the manual mode.
3
Change the incline of the treadmill as desired.
Time/Segment Time/
Pace display—When the
manual mode or the
iFIT.com mode is selected, this display will
show the elapsed time
and your current pace (pace is measured in minutes per mile). The display will change from one
number to the other every few seconds. When a
preset program or a heart rate program is selected, the display will show the time remaining in
the program, the time remaining in the current segment of the program, and your current pace.
Press the Start button or the Speed ▲ button to
start the walking belt.
A moment after the button is pressed, the
walking belt will begin to
move at 1 mph. Hold
the handrails and begin
walking. As you exercise, change the speed of the walking belt as desired by pressing the Speed ▼ and ▲ buttons.
11
Pulse/Calories/Fat
Calories display—This
display shows the approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 28). The display will
change from one number to the other every few
seconds. The display will also show your heart
rate when you use the handgrip pulse sensor (see
step 6 at the right) or the chest pulse sensor (see
page 8).
6
Measure your heart rate if desired.
You can measure your heart rate using either the
handgrip pulse sensor (see the instructions below)
or the chest pulse sensor (see page 8).
To use the
handgrip pulse
sensor, first
make sure that
your hands are
clean. Next,
stand on the
foot rails and
place your
hands on the metal contacts on the handgrip
pulse sensor. Your palms should be resting on the
upper contacts and your fingertips should be
touching the lower contacts. Avoid moving your
hands. When your pulse is detected, two dashes
(– –) will appear in the Pulse/Calories/Fat Calories
display, and then your heart rate will be shown.
For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds.
Distance/Incline/Laps
display—This display
shows the distance that
you have walked, the incline level of the treadmill, and the number of
1/4-mile laps you have completed. The display will
change from one number to the next every few
seconds. Note: Each time the incline changes, the
display will show the current incline setting for several seconds.
Speed display—This
display shows the speed
of the walking belt.
7
Turn on the fans if desired.
To use the fans, press the Low or High button. To
turn off the fans, press the Off button. Note: Any
time that the walking belt is stopped for a few minutes, the fans will automatically turn off.
Note: When the Km/H indicator is lit, the console
will display speed and
distance in kilometers;
when the Km/H indicator
is not lit, the console will
display speed and distance in miles. To change
the unit of measurement, first hold down the Stop
button while inserting the key into the console. An
“E” for English miles or an “M” for metric kilometers
will appear in the Speed display. Press the Speed
▲ button to change the unit of measurement.
When the desired unit of measurement is selected,
remove the key and then reinsert it.
8
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is
removed, the console is in the “demo” mode.
See page 23 and turn off the demo mode.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
12
The speed setting for
Current Segment
the first segment is
shown in the flashing
Current Segment column of the LED matrix.
(The incline settings are
not shown in the matrix.)
The speed settings for
the next seven
segments are shown in the seven columns to the
right.
HOW TO USE PRESET WORKOUT PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the preset workout programs.
When the key is inserted, the manual
mode will be selected.
To select a preset
workout program, press
the Program Select button repeatedly until one
of the Walk, Jog, or Run indicators lights.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, if the speed
and/or incline of the treadmill is about to change,
the Speed display and/or the Distance/Incline/
Laps display will flash to alert you. When the first
segment is completed, all speed settings will move
one column to the left. The speed setting for the
second segment will then be shown in the flashing
Current Segment column and the treadmill will automatically adjust to the speed and incline settings
for the second segment. Note: If all of the indicators in the Current Segment column are lit after the
speed settings have moved to the left, the speed
settings will move downward so that only the highest indicators appear in the LED matrix. If some of
the indicators in the Current Segment column are
not lit when the speed settings move to the left
again, the speed settings will move back up.
When a preset workout program is selected, the
Distance/Incline/Laps display will flash the maximum incline setting for the program, and the
Speed display will flash the maximum speed setting, for six seconds. The Time/Segment Time/
Pace display will show how long the program will
last.
The LED matrix will
show the first seven
speed settings for the
program. The profiles
on the right side of the
LED matrix show how
the speed and incline
of the treadmill will change during the programs.
3
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the Time/Segment
Time/Pace display counts down to zero. The
walking belt will then slow to a stop.
Press the Start button or the Speed ▲ button to
start the program.
If the speed or incline setting is too high or too low
during the program, you can manually override
the setting by pressing the Speed or Incline buttons. Every few times a Speed button is pressed,
an additional indicator will light or darken in the
Current Segment column. (If any of the columns
to the right of the Current Segment column have
the same number of lit indicators as the Current
Segment column, an additional indicator may light
or darken in those columns as well.) Note: If you
manually override the speed or incline setting,
when the next segment begins, the treadmill
will automatically adjust to the speed and incline settings for the next segment.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths. (The Time/Segment
Time/Pace display will show both the time remaining in the program and the time remaining in the
current segment of the program.) One speed setting and one incline setting are programmed for
each segment. (The same speed and/or incline
setting may be programmed for consecutive segments.)
13
To stop the program temporarily, press the Stop
button. The Time/Segment Time/Pace display will
begin to flash. To restart the program, press the
Start button or the Speed ▲ button. To end the
program, press the Stop button, remove the key,
and then reinsert the key.
4
HOW TO USE HEART RATE PROGRAMS
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
Follow your progress with the displays.
See step 5 on page 11.
5
Measure your heart rate if desired.
See step 6 on page 12.
6
Turn on the fans if desired.
Follow the steps below to use a heart rate program.
Note: You must wear the chest pulse sensor (see
page 8) to use a heart rate program.
See step 7 on page 12.
7
1
Put on the chest pulse sensor.
See HOW TO PUT ON THE CHEST PULSE
SENSOR page 8.
When the program is finished, remove the key
from the console.
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place.Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 23 and turn off the
demo mode.
2
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
3
Select a heart rate program.
When the key is inserted, the manual
mode will be selected.
To select a heart rate
program, press the
Program Select button
repeatedly until one of the heart rate program indicators lights.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
The two profiles on the left side of the LED matrix
show how the target heart rate will change during
the programs. During heart rate program 1, your
heart rate will reach approximately 85% of your
estimated maximum heart rate; during heart rate
program 2, your heart rate will reach approximately 80% of your estimated maximum heart
rate. Note: Your estimated maximum heart rate is
determined by subtracting your age from 220. For
example, if you are 30 years old, your estimated
maximum heart rate is 190 beats per minute
(220 – 30 = 190).
14
4
During heart rate programs, the LED matrix
will show a graphic that
represents your heart
rate. Each time a heartbeat is detected, an additional peak will appear.
the treadmill will automatically increase or decrease to bring your heart rate closer to the target
heart rate setting. If the speed reaches the maximum speed setting for the program (see step 4 at
the left) and your heart rate is still too far below
the current target heart rate setting, the incline of
the treadmill will also increase to bring your heart
rate closer to the target heart rate setting.
Enter your age and a maximum speed setting.
During the last three seconds of each segment, a
series of tones will sound and the Distance/
Incline/Laps display and the Speed display will
flash.
When a heart rate program is selected, the
word “AGE” and the
current age setting will
flash in the Pulse/
Calories/Fat Calories
display. If you have already entered your age,
simply press the Enter button. If you have not entered your age, press the ▲ and ▼ buttons beside
the Enter button to enter your age. Then, press
the Enter button.
The program will continue until no time remains in
the program. The walking belt will then slow to a
stop.
If the speed or incline setting is too high or too low
during the program, you can adjust the setting
with the Speed or Incline buttons. However, each
time the console compares your heart rate to the
current target heart rate setting, the speed and/or
incline of the treadmill may automatically change
to bring your heart rate closer to the target heart
rate setting.
After you have entered
your age, the letters
“SPd” and the maximum speed setting for
the program will flash in
the Pulse/Calories/Fat
Calories display. If desired, press the ▲ and ▼ buttons beside the Enter button to adjust the maximum speed setting. When the desired setting is
shown, press the Enter button.
5
If your pulse is not detected during the program,
the letters “PLS” will flash in the Pulse/Calories/
Fat Calories display and the speed and incline of
the treadmill may automatically decrease until
your pulse is detected. If this occurs, refer to the
instructions on page 8.
Press the Start button or the Speed ▲ button to
start the program.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
6
Each heart rate program is divided into several time
segments of different lengths. (The Time/Segment
Time/Pace display will show both the time remaining in the program and the time remaining in the
current segment of the program.) One target heart
rate setting is programmed for each segment.
Follow your progress with the displays.
See step 5 on page 11.
7
Turn on the fans if desired.
See step 7 on page 12.
8
During each segment, the console will regularly
compare your heart rate to the current target heart
rate setting. If your heart rate is too far below or
above the target heart rate setting, the speed of
When the program is finished, remove the key
from the console.
See step 7 on page 14.
15
cline settings are not shown in the matrix.) To program a speed setting and an incline setting for the
first segment, simply adjust the speed and incline
of the treadmill as desired by pressing the Speed
and Incline buttons. Every few times a Speed button is pressed, an additional indicator will light or
darken in the Current Segment column.
HOW TO CREATE CUSTOM PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
When the first segment of the program is completed, a series of tones will sound and the current
speed setting and the current incline setting will
be saved in memory. The three columns of indicators will then move one column to the left, and the
speed setting for the second segment will be
shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
Select one of the custom programs.
When the key is inserted, the manual
mode will automatically
be selected. To select a
custom program, first
press the Program
Select button repeatedly until one of the custom
program indicators lights.
Continue programming speed and incline settings
for as many segments as desired; custom programs can have up to forty segments. When you
are finished with your workout, press the Stop button twice. The speed and incline settings that you
programmed and the number of segments that you
programmed will then be saved in memory.
Note: If the custom program has not yet been
defined, only three columns of indicators will
be lit in the LED matrix. If more than three
columns of indicators are lit, see HOW TO USE
CUSTOM PROGRAMS on page 17.
3
Press the Start button or the Speed ▲ button
and program the desired speed and incline
settings.
4
When the program has ended, remove the key.
See step 7 on page 14.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Refer to the LED matrix. Each custom program is
divided into one-minute segments. One speed
setting and one incline
setting can be proCurrent Segment
grammed for each segment. The speed setting for the first segment will be shown in
the flashing Current
Segment column of the
LED matrix. (The in-
16
The speed settings for the next seven segments
are shown in the seven columns to the right.
HOW TO USE CUSTOM PROGRAMS
1
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, a series of tones will sound, and the Speed display
and/or the Distance/Incline/Laps display will flash.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you programmed previously.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
11.
2
Select one of the custom programs.
When the key is inserted, the manual
mode will automatically
be selected. To select
a custom program, first
press the Program
Select button repeatedly until one of the custom
program indicators lights.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
When a custom program is selected, the
Distance/Incline/Laps display will flash the maximum incline setting for the program, and the
Speed display will flash the maximum speed setting, for six seconds. The Time/Segment Time/
Pace display will show how long the program will
last.
If desired, you can redefine to the program while
using it. To change the speed or incline setting
during the current segment, simply press the
Speed or Incline buttons. When the current segment
is completed, the new setting will be saved in memory. To increase the length of the program, first
wait until the program is completed. Then, press the
Start button and program speed and incline settings
for as many additional segments as desired.When
you have added as many segments as desired,
press the Stop button twice. To decrease the
length of the program, press the Stop button twice
at any time before the program is completed.
The LED matrix will
show the first seven
speed settings for the
program. Note: If only
three columns of indicators are lit in the
matrix, see HOW TO
CREATE A CUSTOM PROGRAM on page 16.
3
To stop the program temporarily, press the Stop
button. The Time/Segment Time/Pace display will
begin to flash. To restart the program, press the
Start button or the Speed ▲ button. To end the
program, press the Stop button, remove the key,
and then reinsert the key.
Press the Start button or the Speed ▲ button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
4
Follow your progress with the displays.
See step 5 on page 11.
Each custom program is divided into several oneminute segments. One speed setting and one incline setting are programmed for each segment.
(The same speed and/or incline setting may be
programmed for consecutive segments.)
Current Segment
The speed setting for
the first segment is
shown in the flashing
Current Segment column of the LED matrix.
(The incline settings
are not shown in the
matrix.)
5
Measure your heart rate if desired.
See step 6 on page 12.
6
Turn on the fans if desired.
See step 7 on page 12.
7
When the program has ended, remove the key.
See step 7 on page 14.
17
HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER
To use iFIT.com CD’s, the treadmill must be connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
18 and 19 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 20 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home computer. See page 19 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
A
PHONES LINE OUT
LINE OUT
LEFT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
PHONES
B
Headphones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
B
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
PHONES
C
PHONES
Audio
Cable
3.5mm
Y-adapter
PHONES
Audio
Cable
Headphones
3.5mm
Y-adapter
Headphones
18
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
B
PHONES
CD
Audio
Cable
VCR
Amp
3.5mm
Y-adapter
LINE OUT
Headphones/Speakers
RCA Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
19
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 19.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFIT.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
18. Note: To purchase iFIT.com CD’s or iFIT.com
videocassettes, call toll-free 1-800-735-0768.
Follow the steps below to use an iFIT.com CD or video
program.
A
1
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 11.
AUDIO OUT
RIGHT
LEFT
2
Audio
Cable
Adapter
Select the iFIT.com mode.
When the key is inserted, the manual
mode will be selected.
To use iFIT.com CD’s
or videocassettes,
press the Program
Select button repeatedly until the iFIT.com indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
3
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com videocassette, insert the videocassette into your VCR.
4
Press the PLAY button on your CD player or
VCR.
B
ANT. IN
VIDEO AUDIO
IN
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time/Pace
display is flashing, press the Start button or the
Speed ▲ button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time/Pace display is flashing.
RF OUT
CH
3 4
OUT
RCA Y-adapter
Audio
Cable
Adapter
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
20
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time/Pace display will begin to flash. To restart
the program, press the Start button or the Speed
▲ button. After a moment, the walking belt will
begin to move at 1 mph. When the next “chirp”
is heard, the speed and incline will change to
the next settings of the CD or video program.
5
Follow your progress with the LED track and
the displays.
See step 5 on page 11.
6
Measure your heart rate, if desired.
Refer to step 6 on page 12.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment
Time/Pace display will begin to flash. Note: To
use another CD or video program, press the Stop
button or remove the key and go to step 1 on
page 20.
7
Turn on the fans if desired.
See step 7 on page 12.
8
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
When the program is completed, remove the
key.
See step 7 on page 14.
• Make sure that the iFIT.com indicator is lit and
that the Time/Segment Time/Pace display is
not flashing. If the Time/Segment Time/Pace
display is flashing, press the Start button or
the Speed ▲ button on the console.
CAUTION: Always remove iFIT.com CD’s and
videocassettes from your CD player or VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
21
7
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Our Web site at www.iFIT.com allows you to access
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon to
be available. See www.iFIT.com for details.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 19. In
addition, you must have an internet connection and
an internet service provider. A list of specific system requirements are found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings for the program.
Follow the steps below to use a program from our
Web site.
1
Insert the key into the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time/Pace display will begin to flash. To restart
the program, press the Start button or the Speed
▲ button. After a moment, the walking belt will
begin to move at 1 mph. When the next “chirp”
is heard, the speed and incline will change to
the next settings of the program.
See HOW TO TURN ON THE POWER on page 11.
2
Select the iFIT.com mode.
When the key is inserted, the manual
mode will be selected.
To use a program from
our Web site, press the
Program Select button
repeatedly until the iFIT.com indicator lights.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop and the Time/Segment Time/Pace display
will begin to flash. Note: To use another program,
press the Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time/Pace display is not
flashing. In addition, make sure that the audio
cable is properly connected, that it is fully
plugged in, and that it is not wrapped around a
power cord.
Read and follow the on-line instructions for using a
program.
6
Return to the treadmill and stand on the foot
pads. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
8
Follow the on-line instructions to start the
program.
Follow your progress with the LED track and
the displays.
See step 5 on page 11.
9
When you start the program, an on-screen countdown will begin.
When the program has ended, remove the key.
See step 7 on page 14.
22
THE INFORMATION MODE/DEMO MODE
An “E” for english miles or an
“M” for metric kilometers will
appear in the Speed display.
Press the Speed ▲ button to
change the unit of measurement.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
IMPORTANT: The Pulse/
Calories/Fat Calories display should be blank. If a
“d” appears in the display, the
console is in the “demo”
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “d” appears in the Pulse/Calories/Fat Calories display
when the information mode is selected, press the
Speed ▼ button so the display is blank.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Time/Segment Time/
Pace display will show the
total number of hours the
treadmill has been used.
The Distance/Incline/Laps
display will show the total
number of miles (or kilometers) that the walking belt
has moved.
To exit the information mode, remove the key from the
console.
23
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Hold the treadmill firmly with your left hand. Using your
right hand, pull the lock knob to the right and hold it.
Raise the treadmill until the pin on the lock knob is
aligned with the hole in the left foam grip. Then, release
the lock knob. Make sure that the lock knob is fully released so that the pin is fully inserted into the hole in
the left foam grip.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
Pin
Foam
Grip
Pin
Lock
Knob
Lock
Knob
Foam
Grip
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
latch pin is securely holding the catch.
1. Hold the handrails and place one foot on the base.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the wheel, and carefully lower the
treadmill until the base is resting in the storage position.
Base
Front Wheels
24
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill firmly with your left hand. Pull the lock
knob to the right. Pivot the treadmill down until the pin on
the lock knob is below the foam grip. Slowly release the
lock knob.
Foam
Grip
Pin
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of injury, bend your legs and keep your back straight.
25
Lock
Knob
TROUBLESHOOTING
Most treadmill problems can be solved by following the instructions below. If further assistance is
needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM
SOLUTION
1. The power does not
turn on
a. Make sure that the power cord is plugged into a surge suppressor, and that the
surge suppressor is plugged into a properly grounded outlet (see page 9). Use
only a single-outlet surge suppressor that meets all of the specifications described
on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
d. Check the on/off switch located on the frame near
the power cord. The switch must be in the on position.
2. The power turns off
during use
c
Tripped
Reset
d
On
Position
a. Check the circuit breaker located on the treadmill frame near the power cord (see
1. c. above). If the circuit breaker has tripped, wait for five minutes and then press
the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.
c. Remove the key from the console and then reinsert it.
d. Make sure that the on/off switch is in the on position (see 1. d. above).
3. The walking belt
slows when walked
on
a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadb
3–4”
mill performance may decrease and the
walking belt may be permanently damaged. Remove the key and UNPLUG THE
POWER CORD. Using the included allen
wrench, turn both rear roller adjustment
bolts counterclockwise 1/4 of a turn. When
the walking belt is properly tightened, you
should be able to lift the edges of the
Rear Roller Adjustment Bolts
walking belt 3 to 4 inches off the walking
platform. Be careful to keep the walking
belt centered. Plug in the power cord, insert the key and run the treadmill for a few
minutes. Repeat until the walking belt is properly tightened.
26
PROBLEM
SOLUTION
4. The walking belt is
off-center or slips
when walked on
a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER
CORD. If the walking belt has shifted to
the left, use the allen wrench to turn the
left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn.
Be careful not to overtighten the walking
belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on,
b
first remove the key and UNPLUG THE
POWER CORD. Using the allen wrench,
turn both rear roller bolts clockwise 1/4 of a
turn. When the walking belt is correctly
tightened, you should be able to lift each
side of the walking belt 3 to 4 inches off the
walking platform. Be careful to keep the
walking belt centered. Plug in the power
cord, insert the key, and walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
5. The displays of the
console do not function properly
a. Remove the key from the console and UNa
PLUG THE POWER CORD. Next, remove
1/8”
the screws from the hood and carefully re11
44
move the hood. Locate the Reed Switch
12
17
(17) and the Magnet (12) on the left side of
the Pulley (11). Turn the Pulley until the
Top
Magnet is aligned with the Reed Switch.
View
Make sure that the gap between the
Magnet and the Reed Switch is about
1/8”. If necessary, loosen the indicated
Screw (44) and move the Reed Switch slightly. Retighten the Screw. Re-attach the
hood and run the treadmill for a few minutes to check for a correct speed reading.
6. The heart rate monitor a. If the heart rate monitor does not function properly,
does not function
refer to CHEST PULSE SENSOR TROUBLESHOOTproperly
ING on page 8.
b. If the heart rate monitor still does not function properly,
the battery should be changed. To replace the battery,
locate the battery cover on the back of the sensor unit.
Insert a coin into the slot in the cover and turn the
cover counterclockwise to the “open” position.
Remove the cover.
Next, remove the old battery from the sensor unit.
Insert a new CR 2032 battery, making sure that the
writing is on top. In addition, make sure that the rubber
gasket is in place in the sensor unit. Replace the battery cover and turn it to the closed position.
27
b
CR2032
Battery
Rubber
Gasket
EXERCISE GUIDELINES
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensors are not medical devices.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
To measure your heart rate during exercise, use the
handgrip pulse sensor or the chest pulse sensor. If
your heart rate is too high or too low, adjust the speed
or incline of the treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
28
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps
and hip muscles.
29
5
PART LIST—Model No. HRTL07120
R0902C
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50*
2
4
1
4
1
1
4
1
2
4
1
1
7
2
2
1
1
1
2
1
20
1
1
1
1
2
4
1
4
1
1
2
1
4
1
1
1
1
1
12
1
2
8
20
1
1
1
2
1
1
Description
Key No. Qty.
Foot Rail
Console Cover Screw
Audio Wire
Isolator
Latch Housing Cover
Platform
Walking Platform Screw
Walking Belt
Frame Pivot Bolt
Frame Pivot Washer
Front Wheel/Pulley
Magnet
Front Roller Nut/Front Wheel Nut
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
Lift Frame
Foot Rail Insert
Pulse Receiver Wire
Foot Rail Screw
Motor Belt
Pulse Receiver
Motor
Transformer
Small Upright Endcap
Hood Bracket
Ground Wire
Star Washer
Right Rear Endcap
Lift Motor Bolt
Motor Bolt
Outlet Bracket
Plastic Stand-off
Power Supply
Power Supply Bracket
Controller
Controller Bracket
Motor Hood
3/4” Screw
Motor Belly Pan
Belt Guide
3/4” Tek Screw
Electronics Screw
Left Front Endcap
Right Front Endcap
Ground Screw
Rear Foot
Console Ground Wire
Motor Assembly
51
52
53
54
55
56
57
58
59*
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
30
1
2
2
1
1
1
2
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
2
1
4
2
2
2
1
1
1
2
2
8
1
1
2
2
1
1
1
1
8
1
2
1
5
2
1
1
Description
Heart Rate Strap
Roller Adj. Washer
Rear Roller Adjustment Bolt
Left Rear Endcap
Frame
Allen Wrench
Rear Platform Screw
Rear Roller
Idler Assembly
Audio Wire Nut
Pulse Bar
Left Foam Grip
Idler Arm
Idler Spring
Upright
Belt Guide Screw
Lock Knob
Latch Housing
Lock Knob Spring
Lock Pin Collar
Pin Clip
Lock Pin
Incline Pivot Bolt
Flywheel
Plastic Fastener
Handrail Extension
Front Wheel
Wheel Bolt
Pulley Nut
Console
Console Cover
Fan
Right Pad
Belly Pan Screw
Upright Wire Harness
Shock
Large Upright Endcap
Left Pad
Filter Wire
Latch Warning Decal
Incline Motor
Motor Controller Wire
Fan Screw
Tie Holder Screw
Tie Holder
Tie
8” Cable Tie
Bumper
Idler Arm Bolt
On/Off Switch
Key No. Qty.
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118*
119
120
121
122
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
2
1
Description
Circuit Breaker
Power Cord
Power Cord Grommet
Warning Decal
Heart Rate Sensor
Jack
iFIT.com Audio Cable
rear Roller Star Washer
Pulley Washer
Idler Pulley
Pulley Spacer
Outlet Bracket Star Washer
Static Decal
Book Plate
Idler Pulley Bolt
Right Foam Grip
Console Base
Latch Assembly
Right Fan Cover
Left Fan Cover
Motor Bushing
Idler Arm Nylon Washer
Key No. Qty.
123
124
125
126
127
128
129
130
131
132
#
#
#
#
#
#
#
#
#
1
1
1
4
1
1
1
2
8
2
1
1
1
1
1
1
1
1
1
Description
Hand Pulse Wire
Incline Bracket
Incline Motor Bolt (Bottom)
Controller Screw
Motor Isolator Plate
Left Cup Holder
Right Cup Holder
iFIT.com CD
Extension Screw
1/2” Screw
8” Blue Wire, 2 F
4” Blue Wire, M/F
4” Blue Wire, 2 F
Blue Wire, M/F
12” Green Wire, F/Ring
8” Green Wire, 2 Ring
14” White Wire, 2 F
4” Black Wire, 2 F
User’s Manual
* Includes all parts shown in the box
# These parts are not illustrated
31
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (HRTL07120)
• The NAME of the product (HealthRider® R60 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on pages 30 and 31)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 187868 R1202A
Printed in USA © 2002 ICON Health & Fitness, Inc.
53
108
21
40
52
1
54
56
40
48
55
57
21
40
108 52
53
90
72
30
4
40
8
6
40
71 69
70
118*
21
19
58
1
40
48
21
68
7
67
To identify the parts shown on this
EXPLODED DRAWING, refer to the
PART LIST on pages 30 and 31.
40
5
44
57
44
28
42
132
21
21
66
4
45
10
19
7
9
29
115
99
7
21
12
110
111
59*
10
109
79
122
13
64
4
40
11
15 14
63
13
21
17
22
66
7
44
16
74
43
46
10
127
4
29
44
84
84
27
43
42
18
24
9
13
25
27
29
14
44
15
10
13 31
32
40
29
121
32
50*
112
43
33
102
27
84
44
43
103
101
27
100
41
44
44
40
38
34
39
126
60
113
35
40
40
37
36
44
3
40
89
EXPLODED DRAWING—Model No. HRTL07120
R1202A
130
62
75
88
13
65
131
76
87
124
40
26
84
125
104
84
131
73
91
43
78
40
123
98
116
75
61
40
13
77
76
84
44
85
131
88
86
40
43
13
131
73
104
40
120
98
13
20
77
26
87
23
2
40
80
78
81
40
14
49
113
40
40
93
117
106
75
128
83
40
40
119
92
93
107
82
96
97
114
95
94
51
105
129
EXPLODED DRAWING—Model No. HRTL07120
R1202A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement