HealthRider HRTL61706.0 User's Manual

HealthRider HRTL61706.0 User's Manual
Model No. HRTL61706.0
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-922-4222
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.healthriderservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.healthrider.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
HealthRider is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
see your local HealthRider dealer or call the
toll-free telephone number on the front cover
of this manual and order part number 146148,
or see your local electronics store.
2. Use the treadmill only as described.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppressor away from heated surfaces.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 22 if the treadmill is
not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 14).
7. The treadmill should be used only by persons
weighing 300 pounds or less.
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
10. When connecting the power cord (see page
12), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
19. Use the included dumbbells only as described in this manual. Properly store the
dumbbells in the dumbbell holders on the
console when you are not using them (see
page 5). If the dumbbells are improperly
stored, they may fall off the console, causing
the user to trip.
11. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 12. To purchase a surge suppressor,
3
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
24. Inspect and properly tighten all parts of the
treadmill regularly.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If
a decal is missing, or if it is illegible, call the toll-free telephone number on the front cover of this manual and order a
free replacement decal. Apply the decal in the location
shown.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary HealthRider®
PRO H450i treadmill. The PRO H450i treadmill offers
an impressive array of features designed to make your
workouts at home more enjoyable and effective. And
when you’re not exercising, the unique PRO H450i
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
ing this manual, please see the front cover of this manual. To help us assist you, please note the product
model number and serial number before contacting us.
The model number of the treadmill is HRTL61706.0.
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Dumbbell/Water Bottle Holder*
Console
Handgrip Pulse Sensor
Key/Clip
Handrail
Storage Latch
Reset/Off
Circuit Breaker
Upright
Power Cord
Walking Belt
Foot Rail
RIGHT SIDE
Cushioned Walking Platform
for maximum exercise comfort
BACK
Rear Roller
Adjustment Bolts
*No water bottle is included
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until
assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping
carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the
walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key
and your own phillips screwdriver
.
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled. To avoid damaging plastic
parts, do not use power tools for assembly.
3/4" Screw (23)–6
3/8" Star
Washer (83)–4
Pulse Bar Star
Washer (65)–4
1" Tek Screw (77)–6
Endcap Screw
(79)–2
2 3/4" Upright Bolt (85)–2
Cover Screw (52)–4
Silver Pulse Bar
Screw (64)–4
Console Screw (67)–4
1 1/4" Bolt (63)–4
1" Upright Bolt (84)–2
1. Make sure that the power cord is unplugged.
1
76
75
With the help of a second person, carefully tip
the treadmill onto its left side as shown. Partially
fold the Frame (26) so that the treadmill is more
stable. Do not fully fold the Frame until the
treadmill is completely assembled.
Post
Wire
Identify the Right Upright (76) which has a
RIGHT sticker. Hold the Right Upright near the
Base (81). Insert the Upright Wire (75) into the
Right Upright until the Upright Wire is extending
from the upper end of the Right Upright. Note:
Make sure that the Upright Wire is extending
from the side of the post as shown in the inset
drawing. Remove the tie from the Upright Wire.
76
81
85
26
83
Thread a 2 3/4" Upright Bolt (85) and a 1" Upright
Bolt (84) with 3/8" Star Washers (83) into the
Base (81) and the bottom of the Right Upright
(76). Do not tighten the Upright Bolts yet.
6
84
2. Remove the packing insert from the location
shown in each side of the Base (81) (only one
side is shown). If necessary, use a tool to help
pry out the insert. Then, discard the insert.
2
79
80
81
Slide a Front Endcap (80) onto the Base (81).
Partially tighten a Endcap Screw (79) into the
Front Endcap and the base.
Slide a Wheel Housing (86) onto the Base (81).
Attach the Wheel Housing with two 1" Tek
Screws (77) and a Base Pad (89) as shown.
86
89
Insert
77
Attach an additional Base Pad (89) to the Base
(81) with a 1" Tek Screw (77).
89
77
3. With the help of a second person, carefully tip
the treadmill onto its right side as shown.
Partially fold the Frame (26) so the treadmill is
more stable. Do not fully fold the Frame until
the treadmill is completely assembled.
3
81
Hold the Left Upright (70) against the Base (81).
Then, thread a 2 3/4" Upright Bolt (85) and a 1"
Upright Bolt (84) with 3/8" Star Washers (83) into
the Base (81) and the bottom of the Left Upright
(70). Do not tighten the Upright Bolts yet.
70
85
84
83
26
4. Slide a Front Endcap (80) onto the Base (81).
Partially tighten a Endcap Screw (79) into the
Front Endcap and the base.
4
80
79
Slide a Wheel Housing (86) onto the Base (81).
Attach the Wheel Housing with two 1" Tek
Screws (77) and a Base Pad (89) as shown.
81
Attach an additional Base Pad (89) to the Base
(81) with a 1" Tek Screws (77).
86
77
89
89
77
7
5. With the help of a second person, carefully raise
the Left Upright (70) and the Right Upright (not
shown) to a vertical position.
5
Remove the knob from the pin. Make sure that
the collar and the spring are on the pin. (Note: If
there are two collars, place one on each side of
the spring.) Then, insert the pin into the Latch
Housing (71), and tighten the knob onto the pin.
70
71
Knob
See steps 2 and 4. Fully tighten the two
Endcap Screws (79).
Spring
Collar
Pin
6. Slide a Handrail (62) onto the post on the Left
Upright (70). Finger tighten two 1 1/4" Bolts (63)
into the Handrail and the post; do not fully
tighten the Bolts yet.
6
63
Post
62
Attach the other Handrail (62) to the Right
Upright (76) in the same way.
63
70
62
76
7. Make sure that the Upright Wire (75) is positioned at the side of the post on the Right
Upright (76) as shown.
7
64
65
Set the Pulse Bar (66) on the Left and Right
Uprights (70, 76). Attach the Pulse Bar with four
Silver Pulse Bar Screws (64) and four Pulse Bar
Star Washers (65). Start all four Silver Pulse
Bar Screws before firmly tightening them.
63
64
66
65
Firmly tighten the four 1 1/4" Bolts (63).
63
70
75
8
76
8. While a second person holds the console assembly near the Pulse Bar (66), connect the
Ground Wire (107) on the Pulse Bar to the
ground wire from the console assembly.
8
Connect the wire from the console assembly to
the Upright Wire (75). Make sure to connect
the connectors properly (see the inset drawing). The connectors should slide together
easily and snap into place. If the connectors
do not slide together easily and snap into place,
turn one connector and then try again. IF THE
CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.
Lay the wires inside the bottom of the Pulse Bar
(66).
Console
Assembly
75
Ground
Wire
107
Wire
75
66
76
9. Set the console assembly on the Left and Right
Uprights (70, 76). Be careful not to pinch any
wires.
9
Console Assembly
Attach the console assembly to the Pulse Bar
(66) with six 3/4" Screws (23). Start all six
Screws, before tighten them yet.
66
23
23
23
76
10.Identify the Left Handrail Cover (68), which has
a LEFT sticker on it. Slide the Left Handrail
Cover onto the left Handrail (62) and up against
the console assembly. Tighten two Cover
Screws (52) into the Left Handrail Cover and the
Left Upright (70); be careful not to overtighten
the Cover Screws.
70
10
Console
Assembly
68
62
Attach the Right Handrail Cover (74) in the same
way.
52
70
74
62
52
9
11.Lower the Uprights (70, 76) as shown.
11
Start the two indicated Console Screws (67) into
the Left and Right Uprights (70, 76) and the console assembly. If necessary, pull back on the
console assembly slightly to align the holes in
the Uprights with those on the console assembly. Start the other two Console Screws before tightening all four; do not overtighten
the Console Screws.
Console Assembly
Start First
67
Start
First
70
67
76
12. See the inset drawing. Push the Uprights (70,
76) sideways so that the treadmill Frame (26) is
centered between the Uprights.
12
Side View
70, 76
Firmly tighten the Upright Bolts (84, 85) on each
side of the treadmill.
85
84
With the help of a second person, carefully raise
the Left Upright (70) and the Right Upright (76)
to a vertical position
26
View From Above
70
26
76
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the large hex key is
used to adjust the walking belt (see page 23).
10
If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Remove the key from the console and unplug
the power cord.
Wire
Remove the 3/4" Screw (23) and the Access Door
(100) from the back of the Console Base (98).
2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Base (98).
Hold the receiver so the small cylinder is oriented as shown and is facing the Console
Base. Attach the receiver to the plastic posts on
the Access Door (100) with the two included
small screws.
Small
Screws
98
100
23
3. Make sure that no wires are pinched. Reattach
the Access Door (100) with the 3/4" Screw (23).
Discard the other wires included with the receiver.
11
A
Small
Cylinder
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local HealthRider dealer or call the toll-free
telephone number on the front cover of this manual and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current, reducing the risk of elec-
12
CONSOLE DIAGRAM
Clip
Key
Note: If there is a sheet of clear plastic
on the face of the console, remove it.
FEATURES OF THE CONSOLE
In addition, the console features four preset programs.
Each program automatically controls the speed and incline of the treadmill as it guides you through an effective workout. The console also features four calorie programs that automatically control the speed and incline
of the treadmill to help you burn unwanted pounds during your workouts.
The treadmill console offers an impressive array of
features designed to make your workouts more effective.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in handgrip
pulse sensor or the optional chest pulse sensor (see
page 19).
To use the manual mode of the console, follow the
steps beginning on page 14. To use a preset
program, see page 16. To use a calorie program,
see page 17.
13
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 12).
2
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
3
If you have selected a program, reselect the manual mode by pressing any of the buttons numbered P1 to P8 once or twice until a track appears
in the lower part of the display.
4
Reset
Position
To start the walking belt, press the Start button,
the Quick Speed increase button, or one of the
speed buttons numbered 1 to 10.
If the Start button or the Quick Speed increase
button is pressed, the walking belt will begin to
move at 1 mph. As you exercise, change the
speed of the walking belt as desired by pressing
the Quick Speed increase and decrease
buttons. Each time a
button is pressed, the
speed setting will
change by 0.1 mph; if a
button is held down, the
speed setting will change in increments of 0.5
mph. Note: After the buttons are pressed, it may
take a moment for the walking belt to reach the selected speed setting.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 13)
and slide the clip onto the waistband of your
clothes. Next, insert the key into the console. After
a moment, the display will light. Important: In an
emergency situation, the key can be pulled
from the console, causing the walking belt to
slow to a stop. Test the clip by carefully taking
a few steps backward; if the key is not pulled
from the console, adjust the position of the
clip.
HOW TO USE THE MANUAL MODE
1
Start the walking belt.
If one of the numbered speed buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting.
Insert the key into the console.
See HOW TO TURN ON THE POWER above.
2
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Quick Speed increase button, or one of the numbered buttons.
Enter your weight if desired.
If you enter your weight
into the console, the
console will display a
more accurate estimate
of the number of calories that you burn. To
enter your weight, press the weight increase and
decrease buttons repeatedly. Note: Once you have
entered your weight, it will be saved in memory.
3
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 23).
5
To change the incline of
the treadmill, press the
Power Incline increase
and decrease buttons.
Each time a button is
pressed, the incline will
change by 0.5%. Note: After the buttons are
pressed, it may take a moment for the treadmill to
reach the selected incline setting.
Select the manual mode.
When the
key is inserted, the
manual
mode will
be selected.
Change the incline of the treadmill as desired.
Track
14
6
Follow your progress with the display.
7
When the
manual
mode is selected, the
lower part of
Track
the display
will show a
1/4-mile track. As you walk or run, the indicators
around the track will appear in succession until the
entire track appears. The track will then disappear
and the indicators will again begin to appear in
succession.
Measure your heart rate if desired.
Note: If you
use the
handgrip
pulse sensor
and the optional chest
Contacts
pulse sensor
at the same
time, the
console will not display your heart rate accurately.
Before using the handgrip pulse sensor, remove
the sheets of clear plastic from the metal contacts.
In addition, make sure that your hands are clean.
The left side of the display will show the incline level of the treadmill, the elapsed time,
and the distance you
have walked or run.
Note: When a program is selected, the display will
show the time remaining in the program instead of
the elapsed time.
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the
handrail—avoid moving your hands. When your
pulse is detected, the heart symbol in the right side
of the display will appear, one or two dashes will
appear, and then your heart rate will be shown.
For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds.
The right side of the
display will show the
speed of the walking
belt, the approximate
number of calories you
have burned, and your
pace (in minutes per mile). The display will also
show your heart rate when you use the handgrip
pulse sensor or the optional chest pulse sensor.
8
Turn on the fan if desired.
To turn on the fan at low speed, press the Cool
Breeze Fan button. To turn on the fan at high
speed, press the button a second time. To turn off
the fan, press the button a third time. Note: If the
fan is left on when the walking belt is stopped, the
fan will automatically turn off after a few minutes.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
9
Note: The console can
display speed and distance in either miles or
kilometers. To determine which unit of
measurement is selected, hold down the Stop button while inserting
the key into the console. An “E” for English miles
or an “M” for metric kilometers will appear in the
right side of the display. Press the Quick Speed increase button to change the unit of measurement.
When the desired unit of measurement is selected,
remove the key. Note: For simplicity, all instructions in this section refer to miles.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 19 and turn off the
demo mode.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
15
the matrix.) The speed settings for the next four
segments will be shown in the columns to the
right.
HOW TO USE A PRESET PROGRAM
1
Insert the key fully into the console.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
See HOW TO TURN ON THE POWER on page
14.
2
Enter your weight if desired.
See step 2 on page 14.
3
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment. Note: If all five of the indicators in the
Current Segment column are lit, the speed settings
may move downward so that only the highest indicators appear in the matrix.
Select one of the preset programs.
To select
one of the
preset programs, press
the P5, P6,
P7, or P8
button. After
each preset
program is
selected, the maximum speed setting of the program and the maximum incline setting of the program will flash in the display for a few seconds.
The display will also show how long the program
will last. The matrix in the lower part of the display
will show the first seven speed settings of the program.
4
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Quick Speed
or Power Incline buttons. Every few times a Quick
Speed button is pressed, an additional indicator
will appear or disappear in the Current Segment
column; if any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may appear or disappear in
those columns as well. Important: When the current segment of the program ends, the treadmill will automatically adjust to the speed and
incline settings for the next segment.
Press the Start button or the Quick Speed increase button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into 30 one-minute segments. One speed setting and one incline setting
are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive segments.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Quick Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings
for the next segment.
The speed
setting for
the first segment will be
shown in the
Current Segment
flashing
Current
Segment column of the matrix in the lower part of
the display. (The incline settings are not shown in
16
5
Follow your progress with the display.
HOW TO USE A CALORIE PROGRAM
See step 6 on page 15.
6
1
Measure your heart rate if desired.
See HOW TO TURN ON THE POWER on page
14.
See step 7 on page 15.
7
2
Turn on the fan if desired.
Enter your weight.
See step 2 on page 14. Note: Always enter your
weight before using a calorie program; the
speed and incline settings of the program will
depend on the weight setting that you enter.
See step 8 on page 15.
8
Insert the key into the console.
When you are finished exercising, remove the
key from the console.
3
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place. Note: If the display remains
lit after the key is removed, the console is in
the “demo” mode. See page 19 and turn off the
demo mode.
Select a calorie program.
To select a
calorie program, press
the P1, P2,
P3, or P4
button. After
each calorie
program is
selected, the
maximum speed setting of the program and the
maximum incline setting of the program will flash
in the display for a few seconds. The display will
also show how long the program will last. The matrix in the lower part of the display will show the
first seven speed settings of the program.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
4
Press the Start button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 30, 35, 40, or 45
one-minute segments. One speed setting and one
incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting
may be programmed for two or more consecutive
segments.
The speed
setting for
the first segment will be
shown in the
Current Segment
flashing
Current
Segment column of the matrix. (The incline settings are not shown in the matrix.) The speed settings for the next four segments will be shown in
the columns to the right.
17
segment of the program begins, the treadmill will
automatically adjust to the speed and incline settings for that segment.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
The program will continue in this way until the last
segment of the program ends. The walking belt
will then slow to a stop. Important: The calorie
goal is an estimate of the number of calories
that you will burn during the program. The actual number of calories that you burn will depend on your weight. In addition, if you manually change the speed or incline of treadmill
during the program, the number of calories
you burn will be affected.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment. Note: If all five of the indicators in the
Current Segment column are lit, the speed settings
may move downward so that only the highest indicators appear in the matrix.
5
Follow your progress with the display.
See step 6 on page 15.
If the speed or incline setting for the current segment is too high or too low, you can manually
override the setting by pressing the Speed and
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column.
Important: When the current segment of the
program ends, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
6
Measure your heart rate if desired.
See step 7 on page 15.
7
Turn on the fan if desired.
See step 8 on page 15.
8
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Quick Speed increase button. The walking belt will begin to move at 1 mph. When the next
When you are finished exercising, remove the
key from the console.
See step 8 on page 17.
18
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also allows you to select miles or kilometers as the unit of
measurement and to turn on and turn off the demo
mode.
An optional chest pulse sensor adds even more features to the console. The chest pulse sensor offers
hands-free operation, and enables you to use the console’s two heart rate programs. To purchase the optional chest pulse sensor, call the toll-free telephone number on the front cover of this manual.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown in the display:
The left side of the display
will show the total number of
miles (or kilometers) that the
Miles
walking belt has moved and
Hours
the total number of hours
that the treadmill has been
used. An “E” for English miles or an “M” for metric kilometers will appear in the right side of the display. Press
the Quick Speed increase button to change the unit of
measurement.
IMPORTANT: If a “d” appears in the right side of the
display, the console is in the “demo” mode. This mode
is intended to be used only when a treadmill is displayed in a store. When the console is in the demo
mode, the power cord can be plugged in, the key can
be removed from the console, and the indicators in the
display will automatically appear in a preset sequence,
although the buttons on the console will not operate. If a
“d” appears when the information mode is selected,
press the Quick Speed decrease button so the “d”
disappears.
To exit the information mode, remove the key from the
console.
19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Make sure to bend your legs and keep your back straight.
As you raise the frame, make sure to lift with your legs
rather than with your back. Raise the frame about halfway
to the vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the latch pin is
aligned with the hole in the center of the cushion. Slowly release the latch knob. Make sure that the latch pin is fully
inserted in the hole in the center of the cushion.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Cushion
Latch
Knob
Latch Pin
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch pin is
fully inserted in the hole in the center of the cushion.
1. Hold the upper ends of the handrails. Place one foot against
one of the wheels.
Handrail
2. Tilt the treadmill backward until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not move the treadmill over an
uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
20
Engaged
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull
the latch knob to the left and hold it. Pivot the frame downward until the catch is past the latch pin.
Frame
Open
Latch
Knob
Latch Pin
2. Hold the metal frame firmly with both hands, and lower it to
the floor. CAUTION: To decrease the possibility of injury, do
not lower the frame by gripping only the plastic foot rails.
Do not drop the frame to the floor. Make sure to bend your
legs and keep your back straight.
Frame
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If you need further assistance, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppressor that meets all of the specifications described on page 12. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes, and then press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. With the help of a second person,
carefully tip the Uprights (70, 76) down as shown.
Remove the three Hood Screws (77), the Belly Pan
Screw (51) and the Large Belly Pan Screw (52). Note:
A phillips screwdriver with a shaft at least 5" long is required.
a
11
70
52
51
76
22
With the help of a second person, carefully raise the
Uprights (70, 76) as shown. Carefully pivot the Hood
(41) off.
70
76
41
Locate the Reed Switch (39) and the Magnet (6) on
the left side of the Pulley (7). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8". If necessary, loosen the Screw
(11), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
7
1/8"
11
39
6
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all the specifications described on page 12.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 inches
above the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
2"–3"
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 inches above the walking platform.
Be careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and carefully
walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
23
a
b
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exercise—never hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
25
5
PART LIST—Model No. HRTL61706.0
R0806A
To locate the parts listed below, see the EXPLODED DRAWING on pages 28 to 31.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
2
10
1
2
2
1
1
2
4
2
13
2
3
1
1
1
2
2
2
2
2
1
22
1
1
1
1
1
2
2
1
1
1
1
2
2
1
1
1
2
6
2
1
1
1
1
1
1
2
7
Description
Key No. Qty.
Foot Rail Cover
Foot Rail Cover Screw
Left Foot Rail
Frame Pivot Bolt
Front Platform Bolt
Magnet
Front Roller/Pulley
Platform Nut
Belt Guide Screw
Belt Guide
Screw
Isolator
Wire Tie
Latch Warning Decal
Walking Belt
Walking Platform
Rear Platform Bolt
Rear Roller Bracket Screw
Rear Roller Bracket
Rear Roller Bolt
Rear Roller Lock Washer
Left Rear Endcap
3/4" Screw
Hex Key
Right Rear Endcap
Frame
Right Foot Rail
Hood
Motor Bolt
Motor Nut
Motor Star Washer
Motor Belt
Drive Motor
Motor Bracket
Motor Tension Bolt
Motor Washer
Lift Frame
Reed Switch Clip
Reed Switch
Lift Frame Spacer
Pivot Nut
Caution Decal
Hairpin Cotter
Motor Pin
Lift Frame
Ground Wire
Front Roller Bolt
Filter Wire
Front Roller Bushing
Tie Block
Plastic Tie
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
26
3
5
1
3
1
1
1
1
9
1
2
2
4
4
4
1
4
1
2
1
1
2
1
1
1
1
6
4
2
2
1
1
4
2
2
2
2
2
4
1
1
1
1
1
1
1
1
1
1
1
Description
Belly Pan Screw
Large Belly Pan Screw/Cover Screw
Belly Pan
Belly Pan Clip
Reset/Off Circuit Breaker
Power Cord Grommet
Power Cord
Controller Bracket
1/2" Screw
Controller
Small Star Washer
Handrail
1 1/4" Bolt
Silver Pulse Bar Screw
Pulse Bar Star Washer
Pulse Bar
Console Screw
Left Handrail Cover
Handrail Cap
Left Upright
Latch Housing
Rear Roller Washer
Latch Pin Assembly
Right Handrail Cover
Upright Wire
Right Upright
1" Tek Screw
Lift Bolt
Endcap Screw
Front Endcap
Base
Roller Ground Wire
3/8" Star Washer
1" Upright Bolt
2 3/4" Upright Bolt
Wheel Housing
Wheel Pin
Wheel
Base Pad
Incline Motor
Stop Bracket
Optic Disk
Photo Switch Nut
Photo Switch
Photo Switch Bolt
Key/Clip
Photo Switch Wire
Console Base
Console
Access Door
Key No. Qty.
101
102
103
104
105
106
107
108
1
2
1
1
1
2
1
1
Description
Console Fan
Fan Screw
Static Decal
Rear Roller
Controller Wire
Dumbbell
Console Ground Wire
Front Roller Nut
Key No. Qty.
#
#
#
#
#
1
1
1
1
1
Description
12" Blue Wire, 2F
12" Blue Wire, M/F
4" Blue Wire, 2F
22" Red Wire, M/F
20" Black Wire, M/F
“#” indicates a non-illustrated part.
Specifications are subject to change without notice.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. When ordering parts, please be prepared to
provide the following information:
• the MODEL NUMBER of the product (HRTL61706.0)
• the NAME of the product (HealthRider PRO H450i treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on
pages 26 to 31)
27
2
28
20
72
19
21
18
2
23
17
22
14
2
24
12
1
20
16
21
72
25
104
11
10
15
23
18
2
9
17
19
2
8
3
2
5
4
26
2
27
7
11
6
12
2
11
9
5
10
8
1
2
4
2
EXPLODED DRAWING A—Model No. HRTL61706.0
R0806A
EXPLODED DRAWING B—Model No. HRTL61706.0
R0806A
11
11
28
29
31
30
30
11
33
32
13
34
50
35
36
35
11
38
39
59
37
59
45
40
11
41
49
44
43
48
105
46
59
53
60
108
82
59
54
61
59
41
51
40
54
23
54
58
55
57
52
56
51
23
51
29
47
EXPLODED DRAWING C—Model No. HRTL61706.0
R0806A
64
65
23
59
107
63
23
62
66
64
65
68
23
67
63
69
52
23
70
62
67
75
74
23
69
71
52
79
76
73
80
41
83
41
78
78
84
85
59
86
75
79
89
42
87
77
78
89
41
80
90
77
81
89
78
88
97
91
92
41
93
61
94
95
77
86
83
85
42
87
89
77
88
30
84
EXPLODED DRAWING D—Model No. HRTL61706.0
96
102
99
23
98
23
23
23
100
23
106
103
23
31
101 102
R0806A
LIMITED WARRANTY
WHAT IS COVERED—The entire HealthRider PRO H450i treadmill (“Product”) is warranted to be free of all defects in
material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the drive motor for 10 years. Parts and
labor are warranted for one year from the date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-922-4222 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 243049 R0806A
Printed in USA © 2006 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement