Hitachi 42PD5000 User's Manual

Hitachi 42PD5000 User's Manual
ENGLISH
01 QR58553-英語-初校 03.10.15 10:47 AM ページ1
USER'S MANUAL
32PD5000
42PD5000
Thank you very much for purchasing the HITACHI Plasma Display
Monitor.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to
operate the monitor properly. Keep this manual in a safe place. You
will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
1
01 QR58553-英語-初校 03.10.15 10:47 AM ページ2
Important
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 4 to 7. Mis-use may cause damage to your
plasma monitor, which could shorten its lifespan, or cause injury to
yourself. Should you encounter any difficulty in the set-up or
operation of your monitor, firstly refer to the Troubleshooting guide at
the rear of this manual.
In the unlikely event of a problem occurring with your plasma monitor,
switch off at the mains sockets, pull out the plugs, and contact your
dealer immediately.
CAUTION
Under no circumstances remove the rear cover of your plasma
monitor.
Never guess or take any chances with electrical equipment of any
kind - it is better to be safe than sorry!
FEATURES
Large-screen, high-definition plasma display
panel
The 42-inch color plasma display panel, with a resolution of 1024 (H)
x 1024(V) pixels, and the 32-inch color plasma display panel with a
resolution of 852(H) X 1024(V) pixels, creates a high-definition, largescreen (aspect ratio : 16:9) and low-profile flat display. Free from
electromagnetic interferences from geomagnetic sources and
ambient power lines, the panel produces high-quality display images
free from color misconvergence and display distortion.
High Performance Digital Processor
A wide range of personal computer signals can be handled, from 640
x 400, 640 x 480 VGA to 1600 x 1200 UXGA.
Software Notice
Easy-to-use remote control and on screen
display system
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, save to
the extent permitted by law.
The remote control included eases the work of setting display controls.
Further, the on-screen display system, displays the status of signal
reception and display control settings in an easy-to-view fashion.
Plasma Monitor
Power saving system
After the plasma monitor has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is normal.
Sometimes the screen might have some tiny bright or dark spots.
Please note that this is normal.
CAUTION
To prevent scratches or damages to the plasma screen, do not
knock or rub the surface with sharp or hard objects. Clean the screen
with a soft cloth moistened with warm water and dry with a soft cloth.
A mild soap may be used if the screen is extremely dirty. Do not use
harsh or abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and control panel of the monitor.
When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or
cracks.
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its
power consumption while it is idle.
TruBass
TruBass, SRS and (O) symbol are trademarks of SRS Labs,Inc.
TruBass technology is incorporated under license from SRS Labs, Inc.
About the Optional Video Unit
The following functions can be obtained by connecting the optional video unit.
(1) A composite/S terminal and two component terminals have been
added. A composite video output terminal is also provided as a
monitoring output.
(2) A wide range of devices other than personal computers can also
be connected.
(3) A component input is possible to switch to RGB signals from the
Menu screen.
(4) A SCART terminal is also provided for the signal of the European
standard. It operates as composite/S/RGB input terminal, or video
output terminal.
Options
Ask your local retail dealer for further details.
1. Desktop stand:
• CMPAD23 (for 32”)
• CMPAD25 (for 42”)
2. Plasma monitor speaker:
• CMPAS03 (for 32”) bass reflex speaker unit with 16x4.5cm
cone type speaker (color: dark gray)
• CMPAS03S (for 32”) same type to CMPAS03 (color: light gray)
• CMPAS14 (for 42”) 2 way speaker unit with one 2.5cm dome
type tweeter and two 8cm round type
woofers (color: dark gray)
• CMPAS14S (for 42”) same type to CMPAS14 (color: light gray)
3. Video unit: CMPAVW1
An expansion unit for viewing video with this device.
2
01 QR58553-英語-初校 03.10.15 10:47 AM ページ3
CONTENTS
Main Unit..............................................................................8
Remote control ....................................................................9
Loading Batteries ..............................................................9
Handling the Remote Control ............................................9
INSTALLATION INSTRUCTIONS ................10
Installation..........................................................................10
Anti-tumble measures........................................................10
Connecting to a PC ..........................................................11
Mounting the Speaker Unit ..............................................12
Power Cord Connection ....................................................12
OPERATING INSTRUCTIONS ....................13
Turning Power On and Off ................................................13
Input Switching ..................................................................14
Volume Adjustment............................................................14
Audio Mute ........................................................................14
Size Switching ..................................................................15
Input Signal Screen Display ..............................................15
Automatic Adjustment of Screen Position and the Clock ..16
Independent Operation of Multiple Monitors ....................16
Using the Menu Screen ....................................................16
PICTURE MENU ................................................................17
AUDIO MENU ....................................................................18
TIMER MENU ....................................................................18
FUNCTION MENU ............................................................19
SETUP MENU ....................................................................20
LANGUAGE MENU............................................................21
OTHER FEATURES ....................................21
Automatic Store ................................................................21
Signal Check ....................................................................22
Power Save Mode..............................................................22
ENGLISH
FEATURES ....................................................2
SAFETY INSTRUCTIONS ..............................4
COMPONENT NAMES ..................................8
IMAGE RETENTION OF PLASMA DISPLAY ......23
NOTES ........................................................23
TROUBLESHOOTING ..................................24
Symptoms That Seemingly Appear to be Failures ............24
Actions to Correct Abnormal Displays ..............................26
PRODUCT SPECIFICATIONS ......................27
Signal Input........................................................................27
Recommended Signal List ................................................28
SUPPLEMENT ............................................30
Optional Video Unit Function ............................................31
Optional Tuner Unit Function ............................................43
Notes about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any
comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the
product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
3
01 QR58553-英語-初校 03.10.15 10:47 AM ページ4
SAFETY INSTRUCTIONS
This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must
be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and
others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions
thoroughly and fully understand the contents.
WARNING
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to
incorrect handling.
CAUTION
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due
to incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables,
penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure Disconnect the
that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be plug from the
power outlet.
dangerous.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children
are present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the
power outlet and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage
and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the plasma screen side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the
monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
4
Do not
disassemble.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ5
ENGLISH
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead,
obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value,
type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed
power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Surely connect
Be careful in handling the power cord and external connection cables.
the ground wire.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat,
pressure or tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them
because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand
holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they
exit from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or
clothes, rinse well with water.
• Obey the local laws on disposing the battery.
5
01 QR58553-英語-初校 03.10.15 10:47 AM ページ6
SAFETY INSTRUCTIONS(continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Disconnect the
plug from the
power outlet.
PRECAUTIONS
• Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
• How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
• Note on image retention
The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the
brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Tips to prevent such image retention are:
- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,
for long.
- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen
saver function.
- Turn down the contrast and brightness controls.
• How to clean the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with
a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or
abrasive cleaners.
• How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
6
01 QR58553-英語-初校 03.10.15 10:47 AM ページ7
• Prevention of an obstacle to Radio receivers
ENGLISH
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
• Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing
connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
• Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
• Precautions for the installation
- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand
or legs with the fixings provided according to the instructions.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the
front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
• Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or
handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
7
01 QR58553-英語-初校 03.10.15 10:47 AM ページ8
COMPONENT NAMES
Front
Main Unit
Cabinet
(front frame)
Panel
Control panel
• Adjustment buttons are located
on the bottom.
• The back cover is provided with
indications to distinguish the
adjustment buttons.
Remote-control
receiver
9
Indicating lamp 13
MENU button 16
• The main power switch is located at the back, on the
lower surface.
Main power switch 13
▼ ▲
INPUT SELECT button 14
VOLUME
(OK button)
UP/DOWN
RECALL button 15
buttons 14
( SELECT button)
(
ADJUST SIZE button 15
buttons)
( SELECT button)
SUB-POWER button 13
• ( ) indicates the function while the MENU is displayed on the screen.
(42")
(32")
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Rear
Handgrips
Handgrips
External
speaker
terminals
External
speaker
terminals
11
11
External device connection terminals
RGB input terminals 11
8
01 QR58553-英語-初校 03.10.15 10:47 AM ページ9
ENGLISH
Remote control
POWER OFF button 13
13 POWER ON/OFF button
POWER ON button 13
MUTE button 14
14 VOLUME UP/DOWN buttons
VOL
RGB/VIDEO buttons 14
PinP button 34
AUTO button 16
MENU button 16
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
15 SIZE button
15 RECALL button
MENU
16 RETURN button
OK
OK button 16
ID
16 SELECT/ADJUST buttons
ID SET
16 ID SET button
ID button 16
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included observing the correct
polarities.
With in 30
degrees
With in 30
degrees
About 3m
About 3m
About 5m
3. Close the battery cover.
VOL
RGB 1
• Replace the battery cover in the direction of the arrow and snap
it back into place.
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical injury,
or stains.
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
MENU
OK
ID
ID SET
ATTENTION
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
9
01 QR58553-英語-初校 03.10.15 10:47 AM ページ10
INSTALLATION INSTRUCTIONS
Installation
• If you have purchased the model without the stand attached:
When installing the monitor, use the optional Desk-top Stand (CMPAD23/25).
The Desk-top Stand has been used for the illustrations in this manual.
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or
dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries
or property damage caused by use of other mount units or improper installation.
10cm (4 inches) or more*
CAUTION
• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work
yourself. Ask your dealer to provide the name of a qualified installer.
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop setup) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not
blocked.(✻)
Clamp
Cord
or
chain
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
cord or chain for 32"
Hook
Chain
cord or chain for 42"
clamp for 32"
Wall or Pillar
clamp for 42"
Securing desktop
1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
10
01 QR58553-英語-初校 03.10.15 10:47 AM ページ11
4
to
7
) carefully to ensure maximum safety before
ENGLISH
Read SAFETY INSTRUCTIONS (
proceeding to these steps:
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "Product Specifications" concerning the specifications of this device. 27 ∼ 29
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the
personal computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker (R)
Speaker (L)
Power cable
connector
Power
cord
(DVI)
To signal
output
terminal
(D-sub)
3.5mm
Stereo
mini jack
To signal
output
terminal
To audio
output
terminal
PC
11
01 QR58553-英語-初校 03.10.15 10:47 AM ページ12
INSTALLATION INSTRUCTIONS (continued)
Mounting the Speaker Unit
(option)
Refer to the instruction manual concerning mounting of the optional speaker unit.
Power Cord Connection
Connect the power cord, after completing all other connections.
①
②
① Connect the power cord to this device.
② Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
12
01 QR58553-英語-初校 03.10.15 10:47 AM ページ13
OPERATING INSTRUCTIONS
Indicating lamp
Main power switch
(42")
ENGLISH
Turning Power On and Off
・ To turn the monitor power ON, press the main power
switch on the monitor main unit to ON, and then press
the SUB POWER button or the ON/OFF or ON button on
the remote control.
・ To turn the monitor power OFF, press the SUB POWER
button or the ON/OFF or OFF button on the remote
control, and then press the main power switch on the
monitor main unit to OFF.
・ During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the ON/OFF button on the remote control.
Indicating lamp
(32")
Indicating
lamp
Power status
Operating
Off
Off
When the main power switch is set
to OFF.
Lights red
Off
(standby)
When the main power switch is
ON, and the OFF button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is OFF.
On
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
Off
(Power Save)
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the underside of the
front of the frame is ON.
However, the state in POWER
SAVE mode
Lights green
SUB-POWER button
Lights orange
POWER OFF
button
POWER ON/OFF
button
POWER ON
button
When the indicating lamp lights in orange or the message “No Sync.
Signal”, “Power Save” or “Invalid Scan Freq.” appears on the
screen, there is something unusual about the status of reception.
See “Power Save Mode” or “Symptoms That Seemingly Appear to be
Failures.” 22 24
ATTENTION
VOL
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
• Avoid repeatedly turning the monitor on and off at short time
intervals. Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out of
use for an extended period of time.
• If a power failure occurs while the main unit is running, it would
be powered on upon recovery from the failure. Turn off the unit
main power switch before leaving the main unit.
MENU
OK
ID
ID SET
13
01 QR58553-英語-初校 03.10.15 10:47 AM ページ14
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
The volume can be adjusted by pressing the VOL+ and
VOL- buttons of the remote control (or the ▲ and ▼
volume buttons of the monitor unit).
Volume setting value
▼ ▲
Volume 15
VOLUME UP/DOWN
buttons
INPUT SELECT button
• When a button is pressed, the volume adjustment
status guide will be displayed.
MUTE button
• The volume will increase when the VOL+ (or ▲) button is
pressed while the guide is being displayed.
• The volume will decrease when the VOL- (or ▼) button is
pressed while the guide is being displayed.
VOL
RGB buttons
Adjustment status guide display
VOLUME
UP/DOWN buttons
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
Audio Mute
The audio volume can be temporarily mute by pressing
the MUTE button of the remote control.
MENU
OK
ID
ID SET
Volume setting value
Volume 15
Adjustment status guide display
(The display color will change to magenta.)
Input Switching
・ Input can be switched by pressing the RGB1, RGB2,
buttons of the remote control.
・ Input can be switched in the sequence of RGB1 →
RGB2 by pressing the INPUT SELECT button of the
monitor.
RGB1
14
RGB2
• When a button is pressed, the volume adjustment
status guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the VOL- button
while the audio is mute.
• The muting can be cancelled by pressing the VOL+ button or
MUTE button while the audio is mute.
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ15
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
ENGLISH
RGB 1
RECALL button
MENU
OK
SIZE button
ID
ID SET
RECALL button
SIZE button
Size Switching
Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in
sequence and the status will be displayed at the bottom of the screen.
Normal
Real*
Full
Zoom3
Zoom1
Zoom2
* Real mode gives the image of the same shape as it is displayed on a computer monitor.
This mode is only available for VGA (640 X 480) and WVGA (864 X 480).
Display area selection diagram (RGB input)
Resolution
Full display
Display
Full
Circular display
Normal
Real
Zoom1
Zoom2
Zoom3
640 X 480
(VGA)
800 X 600
(SVGA)
1024 X 768
(XGA)
1280 X 1024
(SXGA)
1600 X 1200
(UXGA)
* VGA and W-VGA
only
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that
flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On 20 can reduce
the flicker.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the monitor.
・ The display will go out in approximately 6 seconds.
RGB
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
Off-timer
On-timer
OFF
-- -- Min.
-- -- : -- --
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
15
01 QR58553-英語-初校 03.10.15 10:47 AM ページ16
OPERATING INSTRUCTIONS (continued)
Using the Menu Screen
(On-screen display system)
VOL
AUTO button
MENU button
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
RETURN buttons
MENU
SELECT/ADJUST
buttons
OK
When the MENU button is pressed, the adjustment menu
screen will be displayed; from there, PC signal adjustment
and setting is possible by using the SELECT button,
ADJUST button and OK button.
• Refer to 17 - 21
settings.
concerning the adjustment items and the
Example: Selecting the Picture screen
ID SET
ID
ID button
OK button
ID SET button
1. Press the MENU button to display the Main Menu
screen.
MENU
Automatic Adjustment of
Screen Position and the Clock
Adjustment of the screen to a position suitable for the PC
signal and the clock adjustment can be performed
automatically by pressing the AUTO button of the remote
control.
2. Press the OK button to display the Picture Menu
screen. (Use the
and
SELECT buttons to select
other items.)
OK
CAUTION
Perform this adjustment for each input (RGB1 or RGB2) and for
each signal.
* Depending on the signal, satisfactory adjustment may not be
possible in some cases. In such case, adjust by referring to the
Setup Menu item.
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Exit
3. Use the
and
SELECT buttons to select the item to
be adjusted and then use the
and
ADJUST
buttons to adjust (example: Contrast).
Independent Operation of
Multiple Monitors (ID No)
Setting the ID No. of the remote control allows separate
control of up to a maximum of seven monitors.
Remote control ID No. 2 (initially ID no. 1) can be set by
pressing the ID SET button for 2 sec. or more while
holding down the ID button. The number will be
incremented (2…6→7→1→2) when this button pressed
continuously.
The remote control ID no. can be
checked by pressing the ID SET button
while holding down the ID button.
ID Number
Monitor
[1]
R/C
[1]
Monitor ID no.
Remote control ID no.
The ID remote control is operated by pressing the
various buttons while holding down the ID button;
Operation is possible only when the remote control and
monitor ID nos. are the same.
• The remote control can be operated normally by pressing the
various remote control buttons without holding down the ID button.
• Set the monitor using the ID No. of Function MENU. 19
16
Contrast
Next / Prev
+ 31
Adjust
Return
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the
Adjustment Menu screen will be closed automatically.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ17
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
OK Set
OK
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
Select
OK Set
Selected characters
+ 31
– 31
0
+ 31
Off
Normal
OK
Reset
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Contrast
Next / Prev
Reset
Return
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
+ 31
Adjust
Return
OK
Color Temperature
Next/Prev
Select
OK
Reset
Return
▲
▲
Picture
Contrast
Brightness
Color
Tint
Picture Enhancement
Color Temperature
Color Temp.Adjust
Reset
OK Set
Select
:
:
:
:
:
:
ENGLISH
PICTURE MENU
Picture
Color Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
Normal
Return
On
Reset
Return
Setup hint
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
cursor
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For brighter scene some parts of the picture might not be clear. We
recommend to set at [+31].
"Panel Life" in the Function Menu should be set to Normal when
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to taste.
Color
Darkens colors.
Lightens colors.
Adjust to taste.
Tint
Enhances red and weakens
green.
This is not available to adjust when receiving PAL/SECAM signal.
Enhances green and weakens
In this case the character will be grayed out.
red.
Adjust for most realistic skin color.
Off
Picture Enhancement
Color Temperature
Cool
Low
Normal
Amplitude
Reset
High
Black / White
On
Red
Brighter scene is decreased in Brighter scene is increased in
reddish color.
reddish color.
Green
Brighter scene is decreased in Brighter scene is increased in
greenish color.
greenish color.
Blue
Cut Off
Warm
Off
Color Temp. Adjustment
Middle
Red
Sets the clarity of small details to the desired level.
Normally set to Normal.
Turn On when you wish to change color temperature is required to
adjust depending on the user’s preference.
Brighter scene is decreased in Brighter scene is increased in
Adjust color temperature depending on the user’s preference. These
bluish color.
bluish color.
settings are independently stored in each of the 4 Color Temperature
Dark scene is decreased in
Dark scene is increased in
modes.
reddish color.
reddish color.
Green
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Blue
Dark scene is decreased in
bluish color.
Dark scene is increased in
bluish color.
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
17
01 QR58553-英語-初校 03.10.15 10:47 AM ページ18
OPERATING INSTRUCTIONS (continued)
AUDIO MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Selected characters
Movie
Audio Mode
Audio
Audio Mode
Treble
Bass
Balance
SRS TruBass
Matrix Surround
Perfect Volume
Reset
Select
Set
▲
▲
MENU
OK
Music
Speech
Favorite
:
:
:
:
:
:
:
Movie
+ 10
– 10
0L
Middle
Off
Off
Reset
Return
R
Setup hint
Movie: This selects the audio suitable for Movie.
Music: This selects the audio suitable for Music.
Speech: This selects the audio suitable for News, Talk show etc.
Favorite: This mode should be adjusted depending on user’s
preference.
Treble
Suppresses treble.
Enhances treble.
Adjust to taste.
Bass
Suppresses bass.
Enhances bass.
Adjust to taste.
Balance
Suppresses right-side sound.
Suppresses left-side sound.
Adjust to taste.
Middle
SRS TruBass takes advance of the ability of the human ear to be able
to distinguish between two different tones. By using this ability,
TruBass gives enhanced bass sound that otherwise would not be
heard. Adjust it depending on the user’s preference.
Off
SRS TruBass
Low
High
Matrix Surround
Off
On
This features the spacious sound effects of a stadium.
Perfect Volume
Off
On
This will automatically adjust volume so each channel and input has
the same average volume level.
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
TIMER MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Off Timer
On Timer
18
▲
Selected characters
▲
MENU
OK
--Min.
30Min.
60Min.
120Min.
90Min.
--(:--)
hours
(- - : )- minutes
Timer
Off Timer
On Timer
Select
Adjust
:
30Min.
: --:-Return
Setup hint
This function automatically sets the power to standby status when the
indicated time period has elapsed.
This automatically sets the power from standby to ON when the
indicated time period has elapsed. The settable time is 00:00~11:59.
Input the required time by
SELECT buttons on the remote
control.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ19
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Screen Saver
Screen Wipe
Off
60Min.
5Min.
40Min.
10Min.
20Min.
On
60Min.
Off
Black Side Panel
This turns the gray sidebars On/Off when watching normal mode
screen size area. It is always set to Off when the monitor powered
On. It is recommended to set to Off to reduce the panel image
retention.
On
Optional (grayed out)
Default Zoom
Optional (grayed out)
(off the function)
(waiting to reset)
Normal
Extend 1
Extend 2
Panel Life
Off
Mode Display
Standby White
Gamma
Normal
Off
1
On 60Min.
Off
2.2
Reset
Return
This is used to reduce the panel image retention that can occur with
stationary pictures by the white field signal. Select On (continuous
operation) or 60 Min. (time limit operation) and press the OK button.
Press the MENU or RETURN button on the remote control to return to
normal viewing.
Freeze Mode
Inverse
Function
Panel Life
Mode Display
ID Number
Inverse
Standby White
Gamma
Reset
Select
Set
This moves the picture around the screen in small amounts, at set
intervals, to reduce the panel image retention. This is where
stationary objects, such as screen logos, leave a slight image visible
after they should have disappeared.
Optional (grayed out)
1
ID Number
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
Setup hint
Video Power Save
Reset
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
▲
Selected characters
▲
MENU
OK
3
6
4
5
On
Off
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
This function is to suppress the contrast of the screen regardless of
the Contrast setting in the Picture Menu. By this control, power
consumption can be reduced or degradation of a panel can be
mitigated. The order of power consumption is Extend 2 < Extend 1 <
Normal.
If the Contrast setting is changed when this item is set to Extend 1 or
2, it will be changed to Normal automatically.
This can display the Input Signal Screen Display every time the input
mode and signal mode are changed.
Set to OFF if the Input Signal Screen Display is not needed when
switching signals.
On
2
7
ENGLISH
FUNCTION MENU
60Min.
Assigns ID nos. to the monitors so that they can be controlled
individually (up to 7 monitors can be controlled).
This function can change each level of RGB signal invert to reduce
the panel image retention. When this function is required to use,
select On (continuous operation) or 60Min. (time limit operation) and
press the OK button. And press the Menu or Return button to exit.
15Min.
30Min.
120Min.
60Min.
This function is also provided against the image retention. If time is
set for this item, the screen changes into the white pattern when the
monitor enters power save mode, and it will continue for the period of
setting time.
2.2
Normally set to 2.2.
2.8
19
01 QR58553-英語-初校 03.10.15 10:47 AM ページ20
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
OK
Adjust
0
+ 31
– 20
10
Reset
Exit
OK
Horizontal Position
Next / Prev
Adjust
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
Adjust
0
+ 31
– 20
10
Reset
Exit
▲
(Menu)
Auto Adjust*
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Input Level
Moves the horizontal position
to left.
Moves down the vertical
position.
10
Adjust
Setup hint
Adjust
Horizontal Position, Vertical Position, Horizontal Clock and Clock
Pressing the OK button here,
Phase are adjusted automatically.
Automatic regulation is started.
Moves the horizontal position
Adjust the left-side display position.
to right.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
Moves up the vertical position. Adjust the vertical display position.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
Reduces the dot clock
frequency (shrinks the right
side).
Increases the dot clock
frequency (expands the right
side).
Slows the dot clock phase
(shifts slightly to left).
Advances the dot clock phase
Adjust for clear character visibility.
(shifts slightly to right).
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
(off the function)
(waiting to reset)
0.7V
1.0V
Adjust for maximum character clarity.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1.)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button. (This is effective only for RGB2.)
Normally set to 0.7 V. If white is found to spread across the screen, set
to 1.0 V. (This is effective only for RGB2.)
Frequency Display
Off
On
Set this to Off if the frequency information of the Input Signal Screen
Display is not required.
WVGA Type
Off
On
This is only available for W-VGA signal.
When it is set to On, the display area mode can be selected Full or
Real.
Vertical Filter
Off
On
Turn On when concerned about screen flicker.
Frequency Mode
Movie
PC
Set to Movie when viewing moving images on a personal computer.
RGB1
Optional (grayed out)
RGB2
Optional (grayed out)
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
20
Return
0.7V
Off
Off
On
Movie
DVI-PC
RGB
Return
▲
Selected characters
Return
OK
Clock Phase
Next / Prev
Setup
Input Level
Frequency Display
WVGA Type
Vertical Filter
Frequency Mode
RGB1
RGB2
Select
Set
0
01 QR58553-英語-初校 03.10.15 10:47 AM ページ21
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
ENGLISH
LANGUAGE MENU
Language
English
簡体中文
繁體中文
OK
Pycckий
日本語
Select
Return
Exit
Select a language by ▼ ▲ SELECT buttons and press the OK button.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
For every input function, 1 setting
is registered.
Contrast
Menu
Function
Registration condition
Screen Saver
1 setting is registered.
Screen Wipe
(not registered)
Color
Black Side Panel
Tint
Panel Life
(not registered)
1 setting is registered.
Picture Enhancement
Mode Display
Color temperature
ID Number
Brightness
Inverse
Color Temp. Adjust
R Amplitude For every Color Temperature, 1
setting is registered.
G Amplitude
Standby White
Gamma
Setup
B Amplitude
Vertical Position
G Cut Off
(not registered)
For every signal Mode, 1 setting is
registered. (Only for RGB2)
Horizontal Clock
B Cut Off
Clock Phase
Audio Mode
1 setting is registered.
Treble
Bass
For every Audio Mode, 1 setting is
registered.
Balance
1 setting is registered.
Input Level
For every Audio Mode, 1 setting is
registered.
1 setting is registered.
Frequency Display
WVGA Type
Vertical Filter
SRS TruBass
Matrix Surround
Auto Adjust
Horizontal Position
R Cut Off
Audio
Display
Frequency Mode
Language
1 setting is registered.
Perfect Volume
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals with which
all the elements are the same or similar will be handled as the
same signal.
21
01 QR58553-英語-初校 03.10.15 10:47 AM ページ22
OTHER FEATURES (continued)
Signal Check
Changes in the signal status are displayed on the screen as they arise.
Status
Display
When Mode Display is set to ON,
the input signal is switched or
when the RECALL button is
pressed.
RGB
Action
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
OFF
When the sync signal is no longer
detected.
When the input signal does not
match the monitor specifications
or is in an unstable status.
-- -- Min.
-- -- : -- --
• A guide displays No Sync.
Recheck the personal computer
Signal, and Power Save (for
power switch status and the
approx. 5 sec.)
connection status.
• When the condition continues
where the sync signal cannot be
detected, indicator lamp of
power source changes in
orange and the mode switches
to power save mode.
A guide displays Invalid Scan
Freq.
! No Sync. Signal
Recheck the input signal
specifications.
27 ∼ 29
! Invalid Scan Freq.
Power Save Mode
When the RGB1, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
No
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
255W (32")
365W (42")
3W or less (RGB1)
1W or less (RGB2 ; 100V≦AC≦120V)
3W or less (RGB2 ; 120V<AC≦240V)
Returning to operating status
• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.
22
01 QR58553-英語-初校 03.10.15 10:47 AM ページ23
IMAGE RETENTION OF PLASMA DISPLAY
ENGLISH
There are different characteristics that result in panel image retention depending on how the plasma display is used.
Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display
The image retention phenomenon of a plasma panel occurs due to partial phosphor degradation arising from partial character and figure
display.
For example, when the character image as shown in Fig. A at the right is
continuously displayed for a long period of time, the only part of the phosphor
(Red,Green, Blue) that will degrade will be the color of the applicable character
display portion. Consequently, when a white image is displayed on the entire
screen as shown in Fig. a, the character marks displayed up to that time will
become a color difference visible to the eye, but the phosphor will never burn.
【Fig. A】
【Fig. a】
■The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
• The tendency of the phosphor is to degrade more the brighter the characters
and figures are displayed. When images of figures with different levels of
brightness, as shown in Fig. B, are continuously displayed for a long period of
time, it becomes easier for image marks at locations when the brighter figures
are displayed to be noticeable.
【Fig. B】
【Fig. b】
* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention
is seen differs depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display as much as possible.
A function is provided in the display that controls the brightness of the screen to reduce degradation of the panel. Using this function makes it
possible to reduce image retention.
(Refer to Panel Life (Extend 1.or Extend 2 shown on 19 )
• Set the plasma monitor to an “Screen Wipe” or “Inverse” display.
The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be
reduced by displaying a reversed color or completely white screen for about 1 ~ 2 hours after terminating the display.
(Settings can be made using Screen Wipe and Inverse of Function MENU shown on 19 )
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniform for moving images, the occurrence of partial image
retention can be controlled. We recommend to use in combination with moving images such as a DVD.
* Please be careful since image retention will occur if display is left in a two screen display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut and
broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these portions can
be expected to occur, so please be aware.
NOTES
About screen defects
• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright spots
(points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface may
rise in some cases.Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface but
avoid strong impact because there is still danger of glass breakage.
23
01 QR58553-英語-初校 03.10.15 10:47 AM ページ24
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating lamp
off.
• Check the way the power cable is connected.
• Press the power switch.
See page
12
13
• The message “No Sync. Signal” or “Power
Save” is displayed.
! No Sync. Signal
• No picture with the power indicating lamp
lights in orange.
• The message “Invalid Scan Freq.” is
displayed.
! Invalid Scan Freq.
No sync signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging equipment ,
etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
• Check the way the signal cable is connected.
11
11
28
29
• The power indicating lamp is normally lit but
no picture .
24
• Check the contrast and brightness settings (adjust them for higher
contrast and brightness).
• Check the way the signal cable is connected.
• The display image appears flowing
slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot clock
frequency first, the dot clock phase next.)
(RGB input)
• Text displayed across the screen appears
blurred.
• A fine pattern flickers when displayed on the
screen.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control in
opposite direction.
• Check to see if the batteries in the remote control are OK.
11
17
20
26
20
26
9
Symptom
• The temperature of the display panel surface is high.
Point to check
See page
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may cause the
temperature of the panel surface to increase. Please note that this
is not a malfunction.
-
• There are locations on the screen that are different from the
periphery (*).
*Points that do not light, points with brightness different
from that of the periphery, points with color different from
that of the periphery, etc.
• High-precision technology is used to manufacture the plasma
display panel, However in some cases, there are minor defects in
some parts of the screen. Please note that this is not a
malfunction.
• Vertical stripes appear, depending on the screen contents.
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. Depending on the screen
contents, in rare cases this may cause vertical stripes to appear
because of failure to light. Please note that this is not a
malfunction.
• Coarse horizontal stripes appear in FULL display.
• Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
ENGLISH
01 QR58553-英語-初校 03.10.15 10:47 AM ページ25
-
-
20
• Flickering in the form of horizontal lines oscillating up and
down.
(PC INPUT MODE only)
• If the direct frequency from the computer is below 85Hz, try a
higher frequency (upper limit 85Hz). There may be a slight
attenuation of the current image.
• Try turning the Vertical Filter On. For this case however, the
vertical resolution will drop.
• The fan motor is noisy. (Fan application model only)
• Use the fan that controls the temperature in the main body to
lower the temperature of this unit. If the ambient air temperature
increases, the fan will start, the RPMs will increase and motor
noise will grow louder. This is not a malfunction though.
-
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor may
heat up. This is not a malfunction.
-
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images with a
vertical resolution greater than 512 lines are displayed; however,
this is not a malfunction.
-
20
25
01 QR58553-英語-初校 03.10.15 10:47 AM ページ26
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for RGB2)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1).
The display image appears flowing (figure 2) (RGB input).
Vertical
streaks
Figure 1
Before adjustment
Some characters
are blurred.
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Example
ABC
B
ABC
After adjustment
All characters appear
crisp now.
ABC
ABC
After adjustment
All characters are
blurred.
1) Press the AUTO button on the remote control.
Adjustment
procedure
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the
SELECT button and select Setup.
4) Press the OK button. The Setup Menu will be displayed.
5) Press the
SELECT button and select Horizontal Clock.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)
6) Press the
or
ADJUST buttons and search for clear characters over the entire screen.
7) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (figure 2).
A fine pattern flickers when displayed on the screen (figure 3).
Before adjustment
Figure 2
ABCDEFGHIJ
abcdefgABCDEFGabcd
ABCDEFGHIJ
abcdefgABCDEFGabcd
Figure 3
Before adjustment
ABC
ABC
Example
After adjustment
After adjustment
ABC
1) Press the AUTO button on the remote control.
Adjustment
procedure
When adjustment is not possible with Auto Adjust
2) Press the MENU button. The Main Menu will be displayed.
3) Press the
SELECT button and select Setup.
4) Press the OK button. The Setup Menu will be displayed.
5) Press the
SELECT button and select Clock Phase.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
6) Press
or
ADJUST buttons to make the text appear
clean across the screen.
26
6) Press
or
ADJUST buttons to make the text appear
without flickering.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ27
PRODUCT SPECIFICATIONS
Panel
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
852 (H) x 1024 (V) pixels
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding Speakers/Stand)
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
Net weight
(excluding Speakers/Stand)
24.6kg
34.9kg
Ambient
conditions
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
255W / <3W
Audio output
12W + 12W (6Ω)
ENGLISH
Product specifications and designs are subject to change without notice.
365W / <3W
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
43 modes 28
Recommended signal
29
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
Signal Input
RGB terminal (D-sub 15-pin connector)
5
4
3
2
1
10
9
8
7
Pin
Input signal
1
R
2
G or sync on green
3
B
4
No connection
5
No connection
6
R.GND
7
G.GND
Sync signal type
Priority
8
B.GND
H/V separate sync.
1
H/V composite sync.
2
sync.on Green *
3
9
No connection
10
GND
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
15
14 13
12
6
11
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is
not possible. In this case, use H/V separate sync, H/V composite
sync.
27
01 QR58553-英語-初校 03.10.15 10:47 AM ページ28
PRODUCT SPECIFICATIONS (continued)
Signal Input (continued)
DVI terminal (DVI-D)
Pin
Input signal
Pin
1
2
3
4
5
6
7
8
9
10
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
DDC Clock
DDC Data
No Connect
T.M.D.S. Data1T.M.D.S. Data1+
14
15
16
17
18
19
20
21
22
23
+5V Power
Ground (for+5V)
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
Input signal
11
T.M.D.S. Data1/3 Shield
24
T.M.D.S. Clock-
12
T.M.D.S. Data3-
13
T.M.D.S. Data3+
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Frame GND
Recommended Signal List
With Digital RGB signal input (RGB1 input)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal Name
VGA
W-VGA
VESA
Signal mode
Horizontal frequency
Vertical frequency
(kHz)
Resolution
(Hz)
Dot clock frequency
(MHz)
640 X 400
640 X 480
864 X 480
864 X 480
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
70.08
59.94
60.00
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
31.47
31.47
31.02
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
25.18
25.18
33.75
34.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
1024 X 768
75.03
60.02
78.75
• Make sure that the signal of the equipment to be connected is compatible with the specifications of this list.
28
Remarks
WVGA type : On
ENGLISH
01 QR58553-英語-初校 03.10.15 10:47 AM ページ29
With Analog RGB signal input (RGB2 input)
No.
Signal Name
Signal mode
Horizontal frequency
Vertical frequency
(kHz)
Resolution
(Hz)
Dot clock frequency
(MHz)
1
2
VGA
640 X 400
640 X 480
70.08
59.94
31.47
31.47
25.18
25.18
3
W-VGA
864 X 480
59.94
31.47
34.24
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
1024 X 768
1152 X 864
1280 X 1024
1280 X 1024
1280 X 1024
1600 X 1200
1600 X 1200
1600 X 1200
640 X 480
832 X 624
1024 X 768
1152 X 870
1280 X 768
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.02
75.03
85.02
60.00
75.00
85.00
66.67
74.55
74.93
75.06
59.833
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
63.98
79.98
91.15
75.00
93.75
106.25
35.00
49.72
60.24
68.68
47.986
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
94.50
108.00
108.00
135.00
157.50
162.00
202.50
229.50
30.24
57.28
80.00
100.00
81.00
1280 X 768
69.997
56.137
94.760
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
VESA
Macintosh
W-XGA
Remarks
WVGA type : On
• The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position, Vertical Position, Horizontal
Clock and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
29
01 QR58553-英語-初校 03.10.15 10:47 AM ページ30
SUPPLEMENT
30
01 QR58553-英語-初校 03.10.15 10:47 AM ページ31
Optional Video Unit Function
ENGLISH
Additional functions when the optional video unit is installed are as follows: ( 31 ∼ 42 )
INSTALLATION INSTRUCTIONS
Connecting to a Video Imaging Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the imaging device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this
device and the signal output terminal of the imaging device.
Speaker (R)
Speaker (L)
Monitor rear panel
To composite
input terminal
To audio input
terminals
Power
cord
VTR
S-video/Composite video
Do not connect both
plugs at the same time.
Use either of them.
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
DVD player
2
To audio output
terminals
VTR
To component
output terminals
Video disc player
To S video output
terminal
To composite
output terminal
To audio output
terminals
can not
( S-video
)
be
used.
Use if the
video
equipment
has an
S video
input terminal
To audio output
terminals
To component
input terminals
(32") (42")
To component
output terminals
To component
input terminals
Adaptor
Adaptor
with Cable
Set-Top Box
1
[An example of connecting video imaging devices]
• If video equipment with an S video output terminal is used, cabling
by the S video cable is recommended to provide finer video
quality. (If an S video input terminal and a video input terminal of
AV3 connect to the monitor at the same time, S video input would
govern.)
• If the OUTPUT (MONITOR) terminal is connected to an external
monitor with a 75 Ohm terminal, it is possible to view the same
image as on the main unit. But it is possible to monitor only the
composite video signal from AV1, AV2, AV3 or AV4 input that is
displayed on the screen at the time.
• If the adaptor is applied to AV4 input as shown in the drawing, it is
not possible to receive RGB signal.
With RGB component setup
To component video
equipments.
Please use the connection
cable suitable for the terminal
form of video equipment.
Applicable video signals for each input terminal (See PRODUCT SPECIFICATIONS for details.
Terminal
RCA/SCART
Signal
CVBS
AV1
○
○
AV2
○
○
AV3
○
○
AV4
○
○
RGB1
RGB2
S-video
Component
DVI
RGB
PC
D-sub
STB
RGB
)
Remarks
Component
○
Refer to Setup Menu. 38
○
Refer to Setup Menu. 38
○
40
Refer to Setup Menu. 39
○
○
○
Refer to Setup Menu. 39
(○ : Available)
31
01 QR58553-英語-初校 03.10.15 10:47 AM ページ32
OPERATING INSTRUCTIONS
VOL
RGB/VIDEO
buttons
RGB 1
RGB 2
MUTE
VOL
AV1
AV2
AV3
AV4
AUTO
PinP
SIZE
RECALL
SIZE button
MENU
INPUT SELECT button
OK
SIZE button
Input Switching
・ Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control.
・ Input can be switched in the sequence of AV1 → AV2 →
AV3 → AV4 → RGB1 → RGB2 by pressing the INPUT
SELECT button of the monitor.
AV1
RGB2
AV2
RGB1
AV3
AV4
Size Switching
Each time the SIZE button of the remote control or the
monitor is pressed, the screen display size will change in
sequence and the status will be displayed at the bottom
of the screen.
• During VIDEO signal input (AV1, AV2, AV3, AV4, RGB1
(set to [DVI-STB]) and RGB2 (set to [Component]))
4:3
Panoramic
Full
Zoom
Cinema
• The size will fix as Full mode and not change when receiving the
component signal of 1080i/50, 1080i/60 or 720p/60.
Full
Display size selection diagram
When you want to
Set the display size to
Play a 4:3 image in a 16:9 screen faithfully.
4:3
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Panoramic
Play a 16:9 VISTA size image in the 4:3
image faithfully reproduced on the 16:9
screen.
Play a 21:9 Cinema size image in the 4:3
image expanded vertically on the 16:9
screen.
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and
horizontally squeezed.*
32
Input signal
Display screen
Remarks
Blanking occurs on both sides.
(4:3 signal)
Zoom
(Vista)
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
remain at the top and bottom.
In some cases, some slight blanking may
remain at the top and bottom.
Cinema
(Cinema)
Full
(Squeeze)
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a 4:3
screen
01 QR58553-英語-初校 03.10.15 10:47 AM ページ33
Position + 31
Press
ENGLISH
Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows.
1. Press SIZE button and
SELECT buttons during picture size display.
2. Position display will appear.
3. Adjustment range of each picture size are as shown below.
[Panoramic]
- 12 to + 12
[Zoom] and [Cinema]
- 31 to + 31
4. When 1080i/50 or 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position - 31
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV program,
the image would appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or pubic viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
33
01 QR58553-英語-初校 03.10.15 10:47 AM ページ34
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE
If the PinP button on the remote control is pressed MULTI
PICTURE will display.
Activating the P-in-P mode from the RGB input screen
Pressing the PinP button one time will display 2 pictures.
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB)
input.
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons; the audio of the video will be output from
the side on which the speaker icon is located.
• The sub-screen position can be
RGB2
selected up and down by pressing
AV1
SELECT buttons.
• The sub-screen can be selected with
the AV1, AV2, AV3, and AV4 buttons
from the status that the speaker icon
(Subappears on the left side of AV✱ as
screen)
shown in the diagram to the right.
• Pressing the PinP button again or
the RETURN button will cancel the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when
sub-screen is the component signal of 1080i/50 or 1080i/60.
RECALL button
VOL
PinP button
RGB 1
RGB 2
MUTE
AV1
AV2
AV3
VOL
RECALL button
AV4
AV1: Displays the VIDEO input signal of the sub-screen.
AUTO
PinP
SIZE
Activating the Split mode from the video input screen
RECALL
Pressing the PinP button one
time will display 2 pictures.
MENU
OK
ID SET
ID
2 Pictures (Split)
AV1∼AV4
Input terminal
Sub
Main
AV1
∼AV4
AV1
AV2
PAL
NTSC3.58
SECAM NTSC4.43
AV1, AV2
576i
576p
480i
480p
1080i/50
○
○
○
○
○
○
NTSC3.58/4.43
○
○
○
○
○
○
○
576i, 576p
○
○
480i, 480p
○
○
1080i/50
○
○
1080i/60
○
○
720p/60
○
○
○
○
○
○
○
○
○
RGB2
Component
RGB2
STB
Component
Main
○
STB
RGB1
1080i/60 720p/60
PAL, SECAM
RGB1
AV1
AV2
• The speaker icon can be shifted left
and right by pressing the and
SELECT buttons; the audio of the
video will be output from the side on
which the speaker icon is located.
• The same video input mode cannot
be selected for both screens at the
same time.
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
• When the Video input is set to RGB Video, this Split mode is not possible.
• Refer to the table for 2 pictures (Split) mode.
RETURN button
Sub
(○ : Available)
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not
change to power save mode.
• Please be careful since image retention will occur if display is left in a MULTI PICTURE display state for a long period of time.
Input Signal Screen Display
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control or
the monitor.
・ The display will go out in approximately 6 seconds.
34
VIDEO
Off-timer
On-timer
AV1
Composite
OFF
-- -- Min.
-- -- : -- --
Input mode
Signal mode
01 QR58553-英語-初校 03.10.15 10:47 AM ページ35
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
OK
Picture
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Picture
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
Reset
Return
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
ENGLISH
PICTURE MENU
OK
Picture Mode
Next/Prev
Select
Dynamic
Return
Contrast Mode
Next/Prev
Select
Normal
Return
YNR
Next/Prev
Off
Select
Auto Color
Next/Prev
On/Off
OK
OK
OK
Dynamic
OK
Return
Dynamic
OK
Magenta
Red
Yellow
Green
Cyan
Blue
Dynamic
OK
Return
On
Reset
Return
Picture
Color Management
Return
Return
Off
Picture
Color Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
Reset
Select
Picture
Color Temp. Adjust
Color Management
Color Decoding
Select OK Set
Return
On
+ 60
+ 30
0
+ 60
+ 30
0
Reset
Return
On/Off
Picture
Color Decoding
RGB
Red
Green
Color
Tint
R
G
Reset
Select
B
0
+ 60
0
+ 31
Reset
Return
Exit
35
01 QR58553-英語-初校 03.10.15 10:47 AM ページ36
OPERATING INSTRUCTIONS (continued)
Selected characters
▲
▲
PICTURE MENU (continued)
Dynamic
Picture Mode
Dynamic: This setting is best for very bright ambient lighting.
Natural: This setting is for normal lighting conditions.
Natural
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding
cursor
button at [+31]. The color for [+32] to [+40] numbers will change from
white to magenta. This special mode is better for dark scenes.
For normal viewing we recommend that the Contrast is set to [+31].
"Panel Life" in the Function Menu should be set to Normal when this
Contrast setting is adjusted.
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for
increased overall darkness.
Black is set off for increased
overall brightness.
Adjust to taste.
Color
Darkens colors.
Lightens colors.
Adjust to taste.
Sharpness
Soft
Sharp
Normally set to Centre position Shift to the minus (-) side for a softer
effect and plus (+) for sharper picture.
Tint
Enhances red and weakens
green.
This is not available to adjust when receiving PAL/SECAM signal.
Enhances green and weakens
Then the character will be grayed out.
red.
Adjust for most realistic skin color.
Color Temperature
Cool
Normal
Warm
Normal
Contrast Mode
Reset
Auto
(off the function)
YNR
Black / White
Dynamic
(waiting to reset)
Off
Low
Normally set to Cool.
Dynamic:Emphasizes the differences between video shadings to
improve the feeling of contrast.
Normal : The gradation of an image is reproduced as faithfully as
possible.
Auto:Detects image brightness and automatically adjusts for natural
brightness.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Performs picture signal noise reduction. Turn up to reduce noise.
High
Performs color signal noise reduction. Turn up to reduce noise.
And it will be fixed as Off only when selecting DVI-STB mode.
CNR
Film Mode
Off
On
On:Automatically detects the movie film material and faithfully
reproduces the original film image.
Off:Set to OFF when switching between images does not appear
natural.
PAL Comb Filter
Off
On
This is available only when receiving a PAL composite signal. Turn On
to reduce the discolorations in fine picture detail and provides purer
color.
LTI
Adjusts the sharpness of the picture signal.
Off
CTI
Low
Middle
High
Black Enhancement
Adjusts the sharpness of the color signal.
Adjusts the black level compensation.
Auto Color
Off
On
This is available only when receiving an NTSC composite/S.Video
signal. This monitors and adjusts the color to maintain constant color
levels. It also maintains natural flesh tones while preserving fidelity of
background colors.
Color Temp. Adjustment
Off
On
Turn On when you wish to change color temperature depending on
the user's preference.
Amplitude
Red
Brighter scene is decreased in Brighter scene is increased in
reddish color.
reddish color.
Green
Brighter scene is decreased in Brighter scene is increased in
greenish color.
greenish color.
Blue
Red
Cut Off
36
Setup hint
Brighter scene is decreased in Brighter scene is increased in
Adjust color temperature depending on the user’s preference. These
bluish color.
bluish color.
settings are independently stored in each of the 4 Color Temperature
Dark scene is decreased in
Dark scene is increased in
modes.
reddish color.
reddish color.
Green
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Blue
Dark scene is decreased in
bluish color.
Dark scene is increased in
bluish color.
Off
Color Management
Magenta
Magenta is strengthened.
Red is weakened.
Red is strengthened.
Yellow
Yellow is weakened.
Yellow is strengthened.
Green
Green is weakened.
Green is strengthened.
Cyan
Cyan is weakened.
Cyan is strengthened.
Blue
Blue is weakened.
Blue is strengthened.
RGB
Color Decoding
Red
R
G
B
Darkens red only.
Lightens red only.
Green
Darkens green only.
Lightens green only.
Color
Darkens colors.
Lightens colors.
Enhances red and weakens
green.
Enhances green and weakens
red.
Tint
Setup hint
Turn On when the original balance of each color is required to adjust
depending on the user’s preference.
On
Magenta is weakened.
Red
ENGLISH
Selected characters
▲
▲
01 QR58553-英語-初校 03.10.15 10:47 AM ページ37
This adjusts listed colors individually to make them either deeper or
more pure. These settings are independently stored in each of the 4
Color Temperature modes.
Select the single color screen when that is required to adjust R/G/B
level individually depending on the user’s preference. And set it back
to RGB mode that indicates all color after adjusting.
Press the OK button every time the setting is changed.
This adjusts R/G/B level or tint to make the color appear natural for
the user’s preference. These settings are independently stored in
each of the 4 Color Temperature modes.
FUNCTION MENU
1 item is added to the Menu shown in the page 19 .
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Video Power Save
▲
Selected characters
▲
MENU
OK
Off
On
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
Function
Panel Life
Mode Display
ID Number
Inverse
Standby White
Gamma
Reset
Select
Set
Normal
Off
1
On 60Min.
Off
2.2
Reset
Return
Setup hint
This is used to reduce power consumption for video input when there
is no video signal. Setting it On will leads the monitor to the standby
mode when the AV input with no signal is selected.
37
01 QR58553-英語-初校 03.10.15 10:47 AM ページ38
OPERATING INSTRUCTIONS (continued)
SETUP MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
MENU
OK
Setup
System
Color System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
Setup
System
Color System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
Setup
System
Color System
Video Input
Audio Input
Scart Output
RGB1
RGB2
System1
System
OK Set
OK
System2
AV1
AV2
AV3
AV4
Monitor
DVI-STB
Component
HDTV
Return
Select
Auto
PAL
SECAM
PAL
Return
Exit
Setup
Video Input
System 1
OK
AV1
AV2
AV3
AV4
Monitor
DVI-STB
Component
HDTV
Return
Select
System 1
OK
Monitor
DVI-STB
Component
HDTV
Return
▲
Selected characters
▲
Select
Setup
Color System
System 1
Setup
Audio Input
AV1
AV2
AV3
AV4
Select
Auto
Composite/Component
Auto
S.Video
Return
Exit
Stereo
L/Mono
Stereo
L/Mono
Return
Exit
Setup hint
Do not change the original setting.
(System1 : Europe/Asia, System2 : North America)
Color System
AV1
Auto
PAL
SECAM
NTSC3.58
NTSC4.43
This should correspond to the color system of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The system of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
• When the component signal is received, this would be not available
(grayed out).
AV2
AV3
(Same to AV1)
AV4
Video Input
AV1
Auto
HDTV
AV2 (1st step)
RGB
Composite/Component
This should correspond to the signal mode of the signal from the
equipment that is connected to AV2 video input terminal.
AV2 (2nd step)
Auto
HDTV
This step should be set only when [Composite/Component] is selected on
the 1st step. And the procedure is same to AV1.
AV4
38
S.Video
SDTV/DVD
This should correspond to the signal mode of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
SDTV/DVD
Composite
• If the signal from the equipment that is connected to AV4 Scart input
terminal is S.Video or Composite, set this to correspond to that signal.
• If the signal is RGB, it will be automatically recognized and this setting
will have no effect.
ENGLISH
Selected characters
▲
▲
01 QR58553-英語-初校 03.10.15 10:47 AM ページ39
Setup hint
Audio Input
Stereo
AV1
L/Mono
This should correspond to the audio signal from the equipment that is
connected to AV1 audio input terminal. If it is monaural audio, set this to
L/Mono.
AV2
AV3
(Same to AV1)
AV4
Scart Output
Not Available (grayed out)
RGB1
DVI-PC
RGB2 (1st step)
RGB
Auto
RGB2 (2nd step)
DVI-STB
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
Component
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
HDTV
SDTV/DVD
This step should be set only when [Component] is selected on the 1st
step.
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Color
Color Temp. Adjust
1 setting is registered.
For every input function and every
Picture Mode, 1 setting is
registered.
R Amplitude For every Color Temperature, 1
setting is registered.
G Amplitude
Menu
Picture
Function
Setup
Display
-
For every Color Temperature, 1
setting is registered.
AV1
AV2
AV3
AV4
Video Input
Audio Input
G Cut Off
AV1 1 setting is registered.
AV2
AV4
AV1 1 setting is registered.
AV2
AV3
AV4
B Cut Off
For every input function and every
Color Management Picture Mode, 1 setting is
registered.
Magenta 1 setting is registered.
Red
1 setting is registered.
Color For every input function and every
Picture Mode, 1 setting is
Tint registered.
Video Power Save
1 setting is registered.
System
1 setting is registered.
1 setting is registered.
Color System
B Amplitude
R Cut Off
Registration condition
Yellow
Green
Cyan
Blue
Color Decoding
Red
Green
RGB1
RGB2
• The previously recorded items will be lost.
39
01 QR58553-英語-初校 03.10.15 10:47 AM ページ40
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
• The screen becomes dark and the images cannot be seen
during VTR special playback (fast forward, rewind).
Point to check
See page
• This sometimes occurs when a component output VTR such as the
480i is connected.
This is not a malfunction; therefore, please take note that this may
occur. When it does occur, change to composite output, or S.video
output.
–
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit has been inserted.
Panel
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
852 (H) x 1024 (V) pixels
1024 (H) x 1024 (V) pixels
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
24.6kg
34.9kg
Net dimensions
(excluding Speakers/Stand)
Net weight
(excluding Speakers/Stand)
Ambient
conditions
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
255W / <3W
Audio output
12W + 12W (6Ω)
365W / <3W
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
46 modes 29
42
(Video input)
Input terminals
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Video signals
AV1: PAL, SECAM, NTSC4.43, NTSC3.58
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC4.43, NTSC3.58
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: RGB
Input signals
Video output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio monitor-output terminal (SCART)
Recommended signal
15 modes 42
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
40
01 QR58553-英語-初校 03.10.15 10:47 AM ページ41
ENGLISH
Signal Input
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
1
R (PR/CR)
2
G or sync on green (Y)
5
4
3
2
1
10
9
8
7
15
14 13
12
6
11
3
B (PB/CB)
4
No connection
5
No connection
6
R.GND (PR/CR, GND)
7
G.GND (Y, GND)
Sync signal type
Priority
B.GND (PB/CB, GND)
H/V separate sync.
1
H/V composite sync.
2
sync.on Green *
3
8
9
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
No connection
10
GND
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
(
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is
not possible. In this case, use H/V separate sync, H/V composite
sync.
) : With component input
S-input connector pin specifications
Pin
Input signal
1
2
3
4
Y
Y-GND
C
C-GND
Frame
GND
③
①
④
②
Scart connector pin specifications
Pin
Signal
Pin
Signal
1
AUDIO OUT (RIGHT)
12 Not Used
2
AUDIO IN (RIGHT)
13 RGB-R GND
3
AUDIO OUT (LEFT/MONO)
14 GND
4
AUDIO GND
15 RGB-R / S.VHS CHROMINANCE IN
5
RGB-B GND
16 BLANKING SIGNAL
6
AUDIO IN (LEFT/MONO)
17 COMPOSITE VIDEO GND
7
RGB-B IN
18 BLANKING SIGNAL GND
8
AUDIO/RGB SWITCH / 16:9
19 COMPOSITE VIDEO OUT
9
RGB-G GND
20 COMPOSITE VIDEO / S.VHS LUMINANCE IN
10
Not Used
21 GND / SHIELD (CHASSIS)
11
RGB-G IN
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
41
01 QR58553-英語-初校 03.10.15 10:47 AM ページ42
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
With Digital RGB signal input (RGB1 input)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Signal Name
Signal mode
Horizontal Dot clock Setup Menu Condition
Vertical frequency frequency frequency
Resolution
DVI-PC
DVI-STB
(kHz)
(MHz)
(Hz)
480p
720p/60
640 X 400
640 X 480
864 X 480
864 X 480
640 X 480
640 X 480
640 X 480
800 X 600
800 X 600
800 X 600
800 X 600
800 X 600
1024 X 768
1024 X 768
1024 X 768
720 X 480
1280 X 720
70.08
59.94
60.00
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
59.94
60.00
31.47
31.47
31.02
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
31.47
45.00
25.18
25.18
33.75
34.24
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
27.00
74.25
1080i/60
1920 X 1080
60.00
33.75
74.25
VGA
W-VGA
VESA
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Remarks
○
WVGA type : On
○
○
EIA-861
EIA-861
○
EIA-861
(○ : acceptable)
With Composite Input(AV1~AV4 input) and S-video Input (AV3 input).
Signal mode
No.
1
2
Signal Name
NTSC4.43
NTSC3.58
PAL
SECAM
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
59.94
15.73
−
50.00
15.63
−
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
15.73
15.63
−
Resolution
Vertical frequency
(Hz)
525
625
Remarks
With R, G, B Video input (AV2 and AV4 input).
Signal mode
No.
1
Signal Name
Resolution
Vertical frequency
(Hz)
NTSC4.43/3.58
PAL, SECAM
525
625
59.94
50.00
Remarks
With component input (AV1, AV2 and RGB2-component input).
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
50.00
15.63
−
480
59.94
15.73
−
576p
576
50.00
31.26
−
480p
480
59.94
31.47
−
5
1080i/50
1080
50.00
28.13
−
6
1080i/60
1080
60.00
33.75
−
7
720p/60
720
59.94
44.96
−
No.
Signal Name
Resolution
Vertical frequency
(Hz)
1
576i
576
2
480i
3
4
Remarks
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 512 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
42
01 QR58553-英語-初校 03.10.15 10:47 AM ページ43
Optional Tuner Unit Function
ENGLISH
The optional tuner unit can operate when installed with the optional video unit.
Additional functions when the optional tuner unit is installed are as follows: ( 43 ∼ 56 )
COMPONENT NAMES
Remote control (provided for the optional tuner unit)
This type of remote control would be provided for the optional tuner unit as the substitute for the one shown in page
POWER ON / OFF button
PICTURE MODE button
RECALL button
INPUT SELECT button
MENU button
i+
SURROUND button
CH I / II button
MULTI PICTURE (PinP) button
Buttons for MULTI PICTURE mode
RETURN button
SELECT / ADJUST buttons (
I / II
A/B
PROGRAM UP / DOWN buttons
2-4-12
P+
-
)
+
OK
VOLUME UP / DOWN buttons
PDV D
MUTE button
FREEZE button
ZOOM button
FREEZE
DVD CONTROL buttons
ZOOM
PROGRAM SELECT buttons
.
AUDIO MODE button
D/N
MENU
OK button
9
1
2
3
4
5
6
7
8
9
PROGRAM UP / DOWN buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
RGB / VIDEO buttons
TIME button
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included
observing the correct polarities.
With in 30
degrees
With in 30
degrees
About 3m
About 3m
About 5m
D/N
i+
I / II
A/B
MENU
3. Close the battery cover.
2-4-12
P+
-
+
OK
PDV D
• Replace the battery cover in the
direction of the arrow and snap it back
into place.
FREEZE
ZOOM
1
2
4
3
5
7
6
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
ATTENTION
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as marked
on the product. If loaded in the wrong direction, the batteries
could explode or leak, resulting in fires, physical injury, or stains.
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
43
01 QR58553-英語-初校 03.10.15 10:47 AM ページ44
COMPONENT NAMES (continued)
Remote control (provided for the optional tuner unit) (continued)
PICTURE MODE
AUDIO MODE
You may recall the picture mode by
pressing this button. Each time pressed,
picture mode is changed in following
sequence.
You may recall the sound mode by pressing
this button. Each time pressed, sound mode
is changed in following sequence.
Dynamic
Natural
D/N
Movie
Music
Favorite
Speech
MATRIX SURROUND
INPUT SELECT
i+
Press this button to change input
mode.
Press this button to set Matrix
Surround On or Off.
I / II
MULTI PICTURE
With this button, the display change
between “--”,“---”,“-” and AV00 on the
top right hand corner of the screen.
“--” is for 2 digit channel selection, “---”
is for 3 digit channel selection and “-” is
for 1 digit channel selection.
A/B
MENU
RECALL
2-4-12
P+
-
Press this button to change the
screen to multi-pictures. Press it
again to return to normal picture.
CH I/II
+
OK
This button is for A2 / NICAM
models only.
MULTI MODE
P-
In multi-picture mode, pressing this
button will change the multi-picture
mode.
DV D
MUTE
DVD CONTROL
FREEZE
You can use these buttons to operate
the selected brand of DVD player.
Press this button to turn off the set
sound. When press again or the _
volume up button will restore the sound.
ZOOM
1
2
3
4
5
6
7
8
9
PROGRAM SELECT
Press these buttons to select a TV
program directly.
FREEZE
Press this button to change the
picture to freeze mode. Press it again
to return to normal picture.
ZOOM
Press this button can change Picture size.
0
AV1
TIME
Pressing this button can indicate the
time by On-Screen display when
receiving a TV program on the screen
including TELETEXT service with the
time information.
44
AV2
AV3
AV4
RGB1
RGB2
ENGLISH
01 QR58553-英語-初校 03.10.15 10:47 AM ページ45
[Buttons for TELETEXT Mode]
SUBTITLE button
D/N
i+
TV button
I / II
TEXT button
A/B
MENU
COLOR buttons
(RED, GREEN, YELLOW, BLUE)
2-4-12
P+
-
+
OK
PDV D
FREEZE
ZOOM
MODE button
1
2
3
4
5
6
7
8
9
TEXT / TV+TEXT button
PAGE UP / DOWN button
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
REVEAL button
TV / TEXT button
HOLD button
CANCEL button
U. N. L. button
TELETEXT FUNCTION
Buttons on Remote Control
TEXT
TV
TV / TEXT
TEXT / TV + TEXT
Function
Press this to use the TELETEXT services.
Press this to return to the TV mode when in the TELETEXT mode.
This switches the receiver between the TV mode and the TELETEXT mode.
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
MODE
This selects the FASTEXT and FAVORITE modes.
INDEX
This selects the P100 page.
SUB PAGE
This allows receiving of a sub page. When the button is pressed, “S✱✱✱✱” will be displayed at the top left of the screen.
SUB TITLE
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).
CANCEL
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text
page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to
display the TELETEXT screen.
RED
GREEN
YELLOW
BLUE
Each of these buttons selects a link page displayed at the lower part of the screen.
A FAVORITE page can also be stored in the memory using one of the colors. It can then retrieve the page stored by pressing
the appropriate color button.
To store a FAVORITE page :
• press the MODE button ;
• press a color button for the FAVORITE page ;
• enter the FAVORITE page number to be stored and press the same color button again to confirm.
Each time this button is pressed, the screen display mode changes through the following.
U. N. L
normal state
upper half screen enlarged
lower half screen enlarged
HOLD
REVEAL
PAGE UP / DOWN
This holds the page currently being displayed on the screen. Instead of the page number, a "
the screen. Press this button again to release the hold state.
" indicator appears at the top of
This allows hidden information (found on some teletext pages) to be displayed on the screen.
These buttons increase / decrease the TELETEXT page number.
NOTE
・ Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
45
01 QR58553-英語-初校 03.10.15 10:47 AM ページ46
INSTALLATION INSTRUCTIONS
Connecting Antenna
Make sure that the power switch of the monitor is turned off.
Speaker (R)
Monitor rear panel
Speaker (L)
antenna
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
When the "ANT" terminal is connected to outdoor antenna instead of CATV system, please note that a good
antenna adaptor is necessary. See the diagram on the right.
Precautions when connecting the antenna
• Clamp section A using pliers when installing the coaxial cable. If other types of adaptors are used, be sure
that the core and shielding are good.
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat
feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the
screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
• For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
46
01 QR58553-英語-初校 03.10.15 10:47 AM ページ47
OPERATING INSTRUCTIONS
POWER ON/OFF
button
ENGLISH
The functions of the buttons located on the bottom
of the monitor change as shown below:
D/N
i+
I / II
INPUT SELECT
button
A/B
MENU
PROGRAM UP/DOWN
buttons
2-4-12
P+
-
+
OK
P-
VOLUME
UP/DOWN buttons
DV D
▼
▲ ▼
▲
FREEZE
MENU button
MUTE button
ZOOM
ZOOM button
INPUT SELECT button
(OK button)
PROGRAM UP/DOWN button
(
SELECT button)
1
2
3
4
5
6
7
8
9
PROGRAM SELECT
buttons
0
VOLUME UP/DOWN
buttons
(
ADJUST buttons)
RGB/VIDEO
buttons
AV1
AV2
AV3
AV4
RGB1
RGB2
SUB-POWER button
• ( ) indicates the function while the MENU is displayed on the screen.
Input Switching
Size Switching
・ Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control. And
the way to return to a TV channel is as follows:
• Pressing INPUT SELECT button at RGB2 input screen.
• Pressing some PROGRAM SELECT buttons and select a TV
channel.
• Pressing PROGRAM UP/DOWN buttons at the screen without
OSD(On-screen display).
・ Input can be switched in the sequence of TV → AV1 →
AV2 → AV3 → AV4 → RGB1 → RGB2 by pressing the
INPUT SELECT button of the monitor or the remote
control.
TV
RGB2
AV1
AV2
RGB1
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
• During TV mode
4:3
Full
Panoramic
Cinema
Zoom
AV3
AV4
47
01 QR58553-英語-初校 03.10.15 10:47 AM ページ48
OPERATING INSTRUCTIONS (continued)
D/N
RECALL button
i+
MULTI PICTURE
button
I / II
A/B
MENU
SELECT buttons
2-4-12
MULTI MODE
button
A/B button
P+
-
+
OK
PDV D
FREEZE
ZOOM
Displaying MULTI PICTURE
If the MULTI PICTURE button on the remote control is
pressed, multi pictures will display. And then three types
of the screen can be selected by pressing the MULTI
MODE button on the remote control.
The multi picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
2 pictures (Split)
4 pictures
PROGRAM UP/DOWN
buttons
1
2
3
4
5
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
12 pictures
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the A/B button; the audio will be output from the
side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected
by pressing INPUT SELECT button on the remote control.
• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.
• When the Video input is set to RGB Video, multi picture mode is not possible.
• Refer to the table for 2 pictures (Split) mode. 49
5
AV1
A
B
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
▼
• Press [A/B] button to select picture A or picture B indicated by a red triangle. For pictures on right, press
SELECT buttons to select picture. The selected channel number would change green.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The audio can only be output from picture A in 4 pictures mode.
• The same signal input mode cannot be selected for each screens at the same time.
• Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 4 pictures.
• Refer to the table for 4 pictures mode. 49
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
• This function activates only in TV mode.
• After several seconds, it refreshes the picture one by one.
• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode.
AV1
A
B1
8
B2
6
B3 11
1
2
3
4
5
6
7
8
9
10
11
12
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change to
power save mode.
• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.
48
ENGLISH
01 QR58553-英語-初校 03.10.15 10:47 AM ページ49
2 Pictures (Split)
Input terminal
Sub
Main
AV1
∼AV4
AV1∼AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
PAL, SECAM
○
○
○
○
○
○
○
NTSC3.58/4.43
○
○
○
○
○
○
○
576i, 576p
○
○
480i, 480p
○
○
1080i/50
○
○
1080i/60
○
○
720p/60
○
○
○
○
○
○
○
○
○
AV1
AV2
RGB1
STB
RGB2
Component
Main
Sub
○
(○ : Available)
4 Pictures
Input terminal
Sub
Main
AV1
∼AV4
AV1∼AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
PAL, SECAM
○
○
NTSC3.58/4.43
○
○
576i, 576p
○
○
480i, 480p
○
○
1080i/50
○
○
1080i/60
○
○
720p/60
○
○
○
○
AV1
AV2
RGB1
STB
RGB2
Component
Main
Sub 1
Sub 2
Sub 3
(○ : Available)
Input Signal Screen Display
The TV channel status can be displayed on the screen by
pressing the RECALL button of the remote control.
・ The display will go out in approximately 6 seconds.
TV
Off-timer
On-timer
1
ABCDE
OFF
TV position
Name
Sound mode
-- -- Min.
-- -- : -- --
49
01 QR58553-英語-初校 03.10.15 10:47 AM ページ50
OPERATING INSTRUCTIONS (continued)
D/N
i+
I / II
2-4-12
A/B
MENU
P+
-
+
OK
PDV D
FREEZE
FREEZE button
ZOOM
1
2
3
4
5
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
Picture Freezing
[Split]
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
5
• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the “Freeze
Mode” setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and the
other still.
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function
as below:
PAL, SECAM
NTSC3.58/4.43
576i
480i
576p
480p
1080i/50
1080i/60
720p/60
Split
Strobe
○
○
○
○
○
○
○
○
○
○
○
○
○
A
B
[Strobe]
1
2
3
4
5
6
7
8
9
10
11
12
Active
RGB, DVI-PC
(○ : Available)
FUNCTION MENU
Freeze Mode
Default Zoom
50
▲
Selected characters
▲
Refer to the page 37 . (It is same to the Picture Menu of Optional Video Unit Function)
But 2 item is added and 5 items are deleted.
Split
Panoramic
Strobe
4:3
Setup hint
This selects the display condition of the FREEZE mode between Split
(2 pictures) and Strobe (12 pictures).
This selects the screen display size that appears first when the power
turned on.
Mode Display
Not Available (grayed out)
ID Number
Not Available (grayed out)
Inverse
Not Available (grayed out)
Standby White
Not Available (grayed out)
Gamma
Not Available (grayed out)
01 QR58553-英語-初校 03.10.15 10:47 AM ページ51
ENGLISH
SETUP MENU
[During TV mode]
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
OK
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
OK
Off
Return
OK
Off
Return
OK
Setup
Manual Tuning
Position
Frequency
Name
Sound System
Color System
Skip
NR
Select
Return
99
250MHz
ABCDE
BG
Auto
Off
Off
Exit
Setup
Fine Tuning
Select
Prog.No.199
+56
Return
Off
Return
OK
Off
Return
Setup
Sort
Position
100
101
102
103
104
105
106
107
Name
ABCDE
BBC1
----BBC
FGHIJ
XYZAB
---------
Select
Setup
Auto Tuning
Mode
Search
Select
Adjust
MHz
62MHz
83MHz
97MHz
106MHz
175MHz
189MHz
199MHz
225MHz
Return
Exit
Position
Set
Setup
Auto Tuning
Mode
Search
Select OK Set
Return
Setup
Auto Tuning
Position
Scanning Channel Number: 33
OK
Return
Cancel
OK
Cancel
51
01 QR58553-英語-初校 03.10.15 10:47 AM ページ52
OPERATING INSTRUCTIONS (continued)
▲
Selected characters
▲
SETUP MENU (continued)
Setup hint
Auto Tuning
Position
Mode
Select the channel entry method between position setting or direct
setting. And press the OK button to fix it.
• If [Position] is selected, the screen display will be numbers (1~199
and AV00).
• If [Direct] is selected, the screen display will be C✱✱ at the channel
0~99 and S✱✱ at the channel 100~199.
Direct
Search
–
–
Press the OK button and it starts the auto tuning.
Position
–
–
Set the position number(0~199) or channel number(C✱✱, S✱✱) by ▼
▲ PROGRAM UP/DOWN buttons.
Frequency
–
–
• If [Position] has been selected, search the frequency here by
pressing
buttons.
• If [Direct] has been selected, this function will be not available
(grayed out).
▲
▲
Manual Tuning
▲
This is used to input the name of the TV station within 5 letters. After
fixing the cursor on the first digit, select a letter by ▼ ▲ SELECT
buttons and move to next digit by
ADJUST button. Press the OK
button again after finished.
• Selectable letters are “0”~`”9”, ”A”~`”Z”, “+”, “–”, ” ”(blank),
”,”(comma) and ”.”(period) .
Name
( :a letter)
Sound System
Auto
M
Color System
Auto
PAL
NTSC3.58
DK
BG
Select the sound system through the 5 different settings.
I
SECAM
NTSC4.43
Select the color system through the 5 different settings.
Skip
Off
On
If this is set to On, that position will be skipped while selecting
positions by PROGRAM UP/DOWN buttons.
This is automatically set to On for those non-broadcasting channels.
NR
Off
On
If this is set to On, it helps to reduce the noise interference visible on
the screen, especially in the weaker signal reception areas.
Fine Tuning
After completing the fine-tuning, press the RETURN button to exit this
Decreasing the frequency Increasing the frequency
mode.
data for the main tuner
data for the main tuner.
• The variable range is -56 ~ +56.
Sort
(When the Mode in Auto Tuning menu is set to [Direct], this function will be not available (grayed out).)
(A Line of position List)
–
–
Off
Auto Off
Press OK button at the a line that is required to change order, then
the characters will change to green. And move it up or down in the list
by pressing ▼ ▲ SELECT buttons. And press OK button to complete
it. Press the RETURN button to exit.
If this is set to On, the power will be turned off when there is no
transmission signal and no operation for about 10 minutes in the TV
mode.
On
[During VIDEO signal input]
1 item is added to the Menu shown in the page 39 .
Scart Output
52
▼
▼
Selected characters
TV
Monitor
Setup hint
TV:AV4 (Scart) output will be fixed as TV signal output.
Monitor:AV4 (Scart) output can view the image as on the main unit.
But it is possible to monitor only the composite video signal from
AV1, AV2, or AV3 input that is displayed on the screen at the time.
01 QR58553-英語-初校 03.10.15 10:47 AM ページ53
ENGLISH
OTHER FUNCTIONS
A2 / NICAM / Sound Multiplex
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
BILINGUAL / DUAL sound broadcast
NICAM [II]
When bilingual program is received, sound mode display appears in yellow as shown on
right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or ▼ (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Yellow
Green
Yellow
NICAM signal received
[I]
[II]
Yellow
Yellow
NICAM [II]
NICAM [I]
Select I, II or
Green
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
8
When a stereo program is received, sound mode display will appear in red, and you can
press the CH I / II button to select between stereo and mono sound.
Each time the button is pressed,
or ▼ (force mono)appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
NICAM
Select
or
Red
Green
(force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
When a monaural program is received, sound mode display will appear in green.
You can press the CH I / II button to select the sound mode between monaural and forced
mono (sound is same).
Each time the button is pressed, ▽or ▼ (force mono) appear cyclically on the screen.
8
▽
NOTE
・ If sound signal is not strong enough for quality reception, press the CH I / II button until ▼ appears on the screen to receive a clear mono sound.
・ If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until ▼ appears
on the screen to receive a clear mono sound.
53
01 QR58553-英語-初校 03.10.15 10:47 AM ページ54
OPERATING INSTRUCTIONS (continued)
OTHER FUNCTIONS (continued)
DVD Player Selection
• You can use this remote control to operate the selected brand of DVD player by pressing the following buttons on the remote control
simultaneously.
Brands of DVD Player
Press
Brands of DVD Player
Press
Hitachi
RECALL
1
RCA
RECALL
9
Pioneer
RECALL
2
Mitsubishi
RECALL
0
Panasonic
RECALL
3
Onkyo
RECALL
INDEX
Toshiba
RECALL
4
Zenith
RECALL
MODE
Philips
RECALL
5
Orion
JVC
RECALL
6
Shinco
RECALL
CANCEL
Samsung
RECALL
7
Skyworth
RECALL
REVEAL
Sony
RECALL
8
Bubuko
RECALL
TV/TEXT
RECALL
Example
To operate HITACHI DVD player, press and hold the RECALL button, followed by the 1 button.
D/N
i+
I / II
A/B
MENU
RECALL button
2-4-12
P+
-
+
OK
PDV D
FREEZE
ZOOM
MODE button
1
2
3
4
5
6
7
8
9
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
TV / TEXT button
CANCEL button
NOTE
・ Not all models of the listed brands can be operated using this remote control.
54
REVEAL button
SUB PAGE
01 QR58553-英語-初校 03.10.15 10:47 AM ページ55
TROUBLESHOOTING
ENGLISH
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Possible reason
Remedy
(1) Connection of antenna cable to the TV is
poor.
(2) Corroded or poor antenna connections.
(3) Antenna has moved position.
(4) Adverse weather conditions.
(5) Transmitter problems.
(1) Make new connection and/or change antenna
plug.
(2) Make new connections or renew cable.
(3) Re-align antenna.
(4) None.
(5) Check with local Operator.
(1) Antenna has moved position.
(2) TV not tuned correctly.
(3) Adverse weather conditions.
(4) Transmitter problems.
(5) AV Input not set correctly.
(1) Re-align antenna.
(2) Re-tune or fine tune TV.
(3) None.
(4) Check with local Operator.
(5) Check the external equipment connected.
snowy picture - poor sound
multiple images - sound O.K
(1) Interference from electrical or mechanical (1) Check devices for shielding and renew if
motors, fluorescent lights, portable
necessary or move further from TV.
radios etc.
intermittent interference
(1) TV may be in AV mode.
(2) Picture/sound setting set to minimum.
(3) TV in standby or power save mode.
(1) Press the INPUT SELECT button or 0 to 9 buttons
on your remote control to return to normal TV
mode.
(2) Check picture / sound controls (go to MAIN
MENU).
(3) Press POWER ON / OFF button.
no picture or sound
55
01 QR58553-英語-初校 03.10.15 10:47 AM ページ56
PRODUCT SPECIFICATIONS
This table shows the specifications when the optional video unit and tuner unit have been inserted.
Panel
Display
dimensions
Approx. 32 inches (716 (H) x 399 (V) mm, diagonal 820mm)
Approx. 42 inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Resolution
852 (H) x 1024 (V) pixels
1024 (H) x 1024 (V) pixels
830 (W) x 506 (H) x 92 (D) mm
1030 (W) x 636 (H) x 91 (D) mm
24.6kg
34.9kg
Net dimensions
(excluding Speakers/Stand)
Net weight
(excluding Speakers/Stand)
Ambient
conditions
Temperature
Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
Relative humidity
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
255W / <3W
Audio output
12W + 12W (6Ω)
365W / <3W
(RGB input)
Input signals
Input terminals
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
Sync signals
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
Recommended signal
46 modes 29
42
(Video input)
Input terminals
AV1: composite video input terminal (RCA)
AV1: Y PB PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/G PB/B PR/R video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal (RCA)
AV3: L/R audio input terminal (RCA)
AV4: composite video / S video / RGB / L/R audio input terminal (Scart)
Video signals
AV1: PAL, SECAM, NTSC3.58, NTSC4.43
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC3.58, NTSC4.43
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB
AV3: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: PAL, SECAM, NTSC3.58, NTSC4.43
AV4: RGB
Input signals
Video output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
AV4: composite video / L/R audio output terminal (SCART)
Recommended signal
15 modes 42
(RF input)
Input terminals
ANT : 75Ω Unbalanced
RF Video System
PAL B, G, H / I / D, K
SECAM B, G / D, K / K1
NTSC-M
Input signals
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
56
Speaker Systems for Hitachi Plasma Display Monitor
Application Model: 42PD5000*,42PMA500*,42HDM70,CMP421*
Model
CMPAS14/CMPAS14S
User Manual
Thank you for purchasing a Hitachi plasma display speaker system.
READ THE INSTRUCTIONS ON THIS USER MANUAL CAREFULLY.
KEEP THIS USER MANUAL FOR FUTURE REFERENCES.
CAUTION
DO NOT HANDLE MONITOR BY HOLDING THE SPEAKER SYSTEMS.
Caution required
Please be careful handling the speaker systems. Since the front side of the speaker systems
is fragile, please do NOT press hard or subject impacts.
Product Components
Speaker holder (x4)
Speakers (x2)
Speaker cable with core (x2)
Cushions (2)
Mounting screw (x8)
Specifications
Type ...............................2 way 3 speakers.
Bass Reflex
Woofer............................80mm cone type x 2 /
each
Tweeter ..........................25mm dome type
Impedance .....................6Ω
Max. input power............50W
RMS input power............20W
External Dimensions ......101.5 (W) x 635.5 (H)
x 90.5 (D) mm / each
Weight ............................2.1kg / each
Specifications and design subject to possible
modification without notice, due to
improvements.
ENGLISH
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ1
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ2
Caution
Make sure the monitor power is switched off (with the standby/ receive lamp switched off or red)
before you connect or disconnect the speaker cables.
Attach the speaker systems to the monitor.
1
Attach the speaker brackets to the speaker systems.
Attach the screws in a position that allows you to read the speaker holder orientation markers (R), (L).
In the case of (R)
(R)
(L)
Notice
Speaker holder
Use of cushions
screw X 2
In some cases, there can
be a gap between the main
unit and the speaker. You
can attach the cushions
provided to the side of the
speaker system, if desired,
to eliminate the gap.
R
L
screw X 2
2
3
Speaker
holder
Cushion
Attach the cushions
to the sides of the
speakers facing the
main unit.
Align the cushions
to the front of the
back case and affix
them.
Back case
Cushion
Attach the speaker systems to the monitor.
Remove two screws on each side of the monitor
as shown and keep them for re-install. Loosen
two screws on each side of the monitor as
shown so that the speaker holders can be slide
on to them. Insert the loosened screws into the
engaging holes of the speaker holders that are
attached to the speaker system, and slide the
screws downwards. Next, use the previouslyremoved screws to fasten the speaker holders
into the mounting holes in the monitor. Tighten
the four screws to secure.
Right side
Speaker holder
shown the other side
Remove
screws
Loosen
screws
Remove
screws
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Hook this section
on the loosened
screw
Monitor rear side
Attach the connection cables to
the speaker system.
4
Attach the speaker connection
cables to the monitor.
Speaker terminals
Treating the wire ends
Pull off while twisting
- Black + Red
Connect the copper-coloured
wire to the + side
Connect the silver-coloured
wire to the - side
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Connect
the silvercolour wire
How to connect
the speaker
cables
(Speaker side)
Press down
the lever with
your finger
Connect
the coppercolour wire
( ( ) )
Please prepare the supplied
speaker cables.
Insert the
wire
Remove
your finger
Caution required
Be sure to insert the speaker cables securely.
Lock the connection terminal level securely.
How to connect
the speaker
cables
(Monitor side)
Press the
lever down
Insert the
wire
Raise the
lever
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ3
Modèle applicable : 42PD5000*, 42PMA500*, 42HDM70, CMP421*
Modèle
CMPAS14/CMPAS14S
Mode d’emploi
Nous vous remercions d’avoir acheté un Système de haut-parleurs pour Ecran à plasma Hitachi
Veuillez lire attentivement les instructions dans ce Mode d’emploi. Après lecture, veuillez
conserver ce Mode d’emploi afin que vous puissiez vous y référer par la suite le cas échéant.
ATTENTION
Ne pas manipuler l’écran en le tenant par les haut-parleurs.
AVERTISSEMENT
Veuillez manipuler les haut-parleurs avec précaution. Comme la face avant des haut-parleurs
est fragile, NE PAS faire subir de gros chocs aux haut-parleurs.
Composants du produit
Supports des hautparleurs (4)
Haut-parleurs (2)
Câble des haut-parleurs
avec noyau (2)
Coussin (2)
Vis de montage (8)
Caractéristiques techniques
Type ...............................3 haut-parleurs
double, Bass Reflex
Haut-parleur grave (Woofer) ...Type cone 80 mm x
2/chacun
Haut-parleur aigu (Tweeter) ....Type dôme 25 mm
Impédance .....................6 Ω
Puissance de sortie maxi ...50 W
Puissance d’entrée RMS....20 W
Dimensions externes......101,5 (Largeur) X 635,5
(Hauteur) X 90,5
(Profondeur) mm.chacun
Poids ..............................2,1 kg /chacun
Les caractéristiques techniques et le design
peuvent faire l’objet de modifications sans
préavis en vue d’améliorer l’appareil.
FRANÇAS
Système de haut-parleurs pour Ecran à plasma Hitachi
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ4
ATTENTION
Veuillez brancher ou débrancher les câbles des haut-parleurs après avoir mis sans faute l’écran
hors tension (dans l’état de veille ou avec la lampe d’alimentation éteinte ou allumée en rouge).
Fixer les haut-parleurs sur l’écran.
1
Fixer les dispositifs de support des haut-parleurs.
Mettre en place les vis de fixation afin que le sens des supports des haut-parleurs soit correct et dans une
position où l’on puisse lire correctement (R), (L).
Dans le cas de (D).
(D)
(G)
Remarque
Support de haut-parleur
A propos des coussins
Vis x 2
Il existe un espace entre le hautparleur et l’unité principale (écran
plasma). Pour les personnes que
cet espace préoccupe, appliquer
les coussins fournis avec
l’équipement sur le côté des hautparleurs.
R
L
Vis x 2
2
3
Support de
haut-parleur
Coussins
Appliquer les
coussins sur le côté
des coussins.
En faisant
correspondre avec la
face avant du boîtier
arrière, appliquer les
coussins.
Boîtier arrière
Coussin
Fixer les haut-parleurs sur l’écran.
Retirer les deux vis de chaque côté de l’écran
comme indiqué sur la figure et les conserver
soigneusement pour le remontage. Desserrer les
deux vis de chaque côté de l’écran comme indiqué
sur la figure de telle sorte que les supports de hautparleur puisse être monté sur eux en coulissant.
Insérer les vis desserrées dans les trous des
supports de haut-parleurs qui sont fixés au système
de haut-parleur et faire glisser les vis vers les bas.
Ensuite, utiliser les vis qui ont été enlevées pour
fixer les supports de haut-parleurs dans les trous de
montage situés sur l’écran. Resserrer les quatre vis
pour bien immobiliser le dispositif.
Côté droit
Support de haut-parleur
vu de l’autre côté
Retirer
les vis
Vis
desserrées
Retirer
les vis
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Accrocher cette
partie sur la vis
desserrée
Côté arrière de l’écran
Installer les câble de branchement
des haut-parleurs
4
Brancher les câbles de connexion
des haut-parleurs à l’écran à plasma
Terminaux des
haut-parleurs
Préparation des
extrémités des câbles
Tirer tout en tordant
- Noir
Brancher le câble couleur
cuivre au côté +
+ Rouge
Brancher le câble couleur
argentée au côté スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Brancher le
câble de couleur
argentée
Comment connecter
les câbles des hautparleurs
(côté haut-parleur)
Appuyer vers
le bas sur le
levier avec votre
doigt
Brancher le
câble de couleur
cuivre
( ( ) )
Veuillez préparer les câbles de hautparleur fournis avec l’équipement
Insérer le
câble
Retirer
votre doigt
Comment connecter
les câbles des hautparleurs
(côté écran)
Appuyer
vers le bas
sur le levier
PRECAUTIONS
Veuillez bien insérer les câbles des haut-parleurs.
Veuillez verrouiller sans faute le levier du connecteur de branchement.
Insérer le
câble
Remonter
le levier
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ5
Lautsprecherboxen für Hitachi Plasma-Displaymonitor
Geeignetes Modell: 42PD5000*,42PMA500*,42HDM70,CMP421*
Modell
Herzlichen Glückwunsch zum Kauf des HITACHI Plasmadisplay-Lautsprechersystems.
BITTE LESEN SIE DIE ANWEISUNGEN DIESER BEDIENUNGSANLEITUNG
SORGFÄLTIG DURCH.
BEWAHREN SIE DIESE ANLEITUNG ZUM ZUKÜNFTIGEN NACHSCHLAGEN AUF.
VORSICHT
TRAGEN SIE DEN MONITOR NICHT, INDEM SIE DIE LAUTSPRECHERBOXEN GREIFEN.
Vorsicht erforderlich
Bitte die Lautsprecherboxen vorsichtig behandeln. Da die Vorderseite der Lautsprecherboxen
empfindlich ist, NICHT stark andrücken oder anstoßen.
Produktkomponenten
Technische Daten
Typ .................................2 Wege 3 Lautsprecher.
Lautsprecherhalterung (x4)
Lautsprecher (x2)
Lautsprecherkabel mit Ader (x2)
Polster (2)
Befestigungsschraube (x8)
Bassreflex
Tieftöner .........................80 mm Konustyp x je 2
Hochtöner.......................25 mm Kalottentyp
Impedanz .......................6 Ω
Max. Eingangleistung.....50 W
Effektiv-Eingangsleistung ...20 W
Außenabmessungen ......Je 101,5 (B) x 635,5
(H) x 90,5 (T) mm
Gewicht ..........................Je 2,1 kg
Änderungen bei technischen Daten und Design
im Sinne der Produktverbesserung bleiben
vorbehalten.
DEUTSCH
CMPAS14/CMPAS14S Bedienungsanleitung
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ6
Vorsicht
Stellen Sie sicher, dass der Monitor ausgeschaltet ist (mit Standby/Empfang-Lämpchen
erloschen oder rot), bevor Sie die Lautsprecherkabel anschließen oder abtrennen.
Bringen Sie die Lautsprecherbügel am Monitor an.
1
Bringen Sie die Lautsprecherbügel an den Lautsprecherboxen an.
Bringen Sie die Schrauben in einer Position an, die es erlaubt, die Lautsprecherhalter-Ausrichtmarkierungen (R), (L) zu sehen.
Bei (R)
(R)
(L)
Hinweis
Lautsprecherhalterung
Verwendung von Polstern
Schraube X 2
In manchen Fällen kann ein
Abstand zwischen Hauptgerät und
Lautsprecher auftreten. Sie können
wenn gewünscht die mitgelieferten
Polster an der Seite der
Lautsprecherbox anbringen, um
diesen Abstand zu beseitigen.
R
L
Lautsprecherhalterung
Schraube X 2
2
3
Bringen Sie die
Polster
Polster an den
Seiten der
Lautsprecher an,
die zum Hauptgerät
weisen.
Fluchten Sie die
Polster zur Vorderseite
der Rückwand und
bringen sie an.
Rückwand
Polster
Bringen Sie die Lautsprecherbügel am Monitor an.
Entfernen Sie die beiden Schrauben an jeder Seite des
Monitors wie gezeigt und bewahren Sie sie zur
Wiederanbringung auf. Lösen Sie die beiden Schrauben
an jeder Seite des Monitors wie gezeigt, so dass die
Lautsprecherhalterungen darauf gleiten können. Setzen
Sie die gelösten Schrauben in die Einsetzlöcher an den
Lautsprecherhalterungen am Lautsprechersystem ein,
und schieben Sie die Schrauben nach unten.
Dann verwenden Sie die vorher entfernten Schrauben
zum Befestigen der Lautsprecherhalterungen an den
Montagelöchern des Monitors. Ziehen Sie die vier
Schrauben zur Befestigung an.
Rechte Seite
Lautsprecherhalterung
auf der anderen Seite
gezeigt
Schrauben
entfernen
Schrauben
lösen
Schrauben
entfernen
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Haken Sie diese
Sektion auf die
gelöste Schraube
Monitor-Rückseite
Bringen Sie die Verbindungskabel
an der Lautsprecherbox an.
4
Bringen Sie die Lautsprecherverbindungskabel
am Monitor an.
Anschlüsse für
Lautsprecher
Behandlung der Drahtenden
Beim Drehen abziehen
- Schwarz + Rot
Schließen Sie den kupferfarbigen
Draht an der + Seite an.
Schließen Sie den silberfarbigen
Draht an der - Seite an.
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Schließen Sie den
silberfarbigen
Draht an
Anschließen der
Lautsprecherkabel
(Lautsprecherseite)
Drücken Sie
den Hebel mit
dem Finger ein
Schließen Sie den
kupferfarbigen
Draht an
( ( ) )
Bitte bereiten Sie die mitgelieferten
Lautsprecherkabel vor.
Setzen Sie
den Draht ein.
Nehmen Sie
den Finger
weg
Vorsicht erforderlich
Setzen Sie die Lautsprecherkabel fest ein.
Sperren Sie den Anschlussterminalhebel sicher.
Anschließen der
Lautsprecherkabel
(Monitor-Seite)
Drücken Sie
den Hebel
ein
Setzen Sie
den Draht ein
Heben Sie
den Hebel
an
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ7
Sistemi Audio per Schermo al Plasma Hitachi.
Utilizzabile con i seguenti modelli: 42PD5000*,42PMA500*,42HDM70,CMP421*
Modello
CMPAS14/CMPAS14S
Manuale Utente
ITALIANO
Grazie per l’acquisto del sistema audio Hitachi per schermo al plasma.
Leggere attentamente le istruzioni contenute in questo manuale utente.
Conservare il manuale utente per riferimenti futuri.
Attenzione
Non maneggiare lo schermo attraverso il sistema audio.
Fare attenzione
Manneggiare con cautela il sistema audio. A causa della fragilita’ della parte anteriore del
sistema audio, fare attenzione a non sottoporre a forte pressione o ad impatti.
Componenti del Prodotto
Supporto per
altoparlante (x4)
Altoparlanti (x2)
Cavo con anima per
altoparlante. (x2)
Ammortizzatori
(2)
Viti di montaggio (x8)
Caratteristiche
Tipo ................................2 vie 3 casse. Basso
con Reflex
Woofer............................80mm tipo a cono x
2/ciascuno
Tweeter ..........................25 mm tipo a cupola
Impedenza .....................6 Ω
Potenza massima d’ingresso ...50 W
Potenza d’ingresso RMS....20 W
Dimensioni Esterne ........101,5 (Spessore) x
635,5 (Altezza) x 90,5
(Diametro) mm/ciascuno
Peso ...............................2,1 kg/ciascuno
Le caratteristiche ed il design sono soggetti a
possibili modificazioni senza avviso, dovuto a
miglioramenti.
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ8
Attenzione
Assicurarsi dello spegnimento dello schermo (con la luce di standby/ricezione, spenta o rossa)
prima di connettere o sconnettere i cavi audio.
Fissare il sistema audio allo schermo
1
Fissare i supporti degli altorparlanti al sistema audio.
Fissare le viti in una posizione che permetta di leggere l’orientamento del supporto degli altoparlanti (R), (L).
In caso di (R)
(R)
(L)
Nota
Supporto altoparlante
Uso degli ammortizzatori
Viti x 2
In alcuni casi, potrebbe crearsi
dello spazio tra l'unita' principale e
gli altoparlanti.
Se lo si desidera, e' possibile
eliminarlo fissando
sul lato del sistema audio gli
ammortizzatori forniti.
R
L
Viti x 2
2
3
Supporto
altoparlante
Ammortizzatore
Fissare gli ammortizzatori
ai lati degli altoparlanti
mantenendoli rivolti
verso l'unita' principale.
Allineare gli
ammortizzatori sulla
parte posteriore del
contenitore e applicarli.
Parte posteriore
del supporto
Ammortizzatore
Fissare il sistema audio allo schermo
Togliere le due viti su ogni lato del monitor
come illustrato e tenerle per il riassemblamento. Allentare le due viti su
ogni lato del monitor come illustrato in
modo da potervici far slittare sopra i
sostegni delle casse. Inserire le viti allentate
nei fori dei sostegni delle casse, che sono
attaccati al corpo delle casse, e far slittare
le viti verso il basso. In seguito, usare le viti
rimosse precedentemente per stringere i
sostegni negli appositi fori nel monitor.
Stringere le quattro viti per fissare.
Lato destro
Il supporto degli
autoparlanti mostrato
sull’altro lato
Rimuovere
le viti
Viti
allentate
Rimuovere
le viti
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Agganciare
questo lato alle
viti allentate
Lato posteriore dello schermo
Collegare i cavi di connessione al
sistema audio.
4
Collegare i cavi di connessione
audio allo schermo
Terminali dell’altoparlante
Trattare gli estremi dei cavi
Tirare durante la torsione.
- Nero
Collegare il cavo color
rame al polo +
+ Rosso
Collegare il cavo color
argento al polo スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Connettere il
cavo color
argento
Come collegare
i cavi di
connessione
(lato altoparlanti)
Premere in
basso la leva
con le dita
Connettere il
cavo color
rame
( ( ) )
Preparare i cavi forniti
Inserire
il cavo
Rimuovere
il dito
Come collegare
i cavi degli
altoparlanti
(lato dello schermo)
Fare attenzione
Assicurarsi di inserire in modo sicuro i cavi degli altoparlanti.
Chiudere in modo sicuro il livello connesione terminali
Premere in
basso la leva
Inserire il
cavo
Alzare
la leva
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ9
Sistema de altavoces para el Monitor Plasma de Hitachi
Modelo Aplicable: 42PD5000*,42PMA500*,42HDM70,CMP421*
Modelo
CMPAS14/CMPAS14S
Manual del Usuario
Muchas gracias por la adquisición del Sistema de Altavoces para el Monitor Plasma de Hitachi.
LEA CUIDADOSAMENTE INSTRUCCIONES CONTENIDAS EN ESTE MANUAL DEL
USUARIO. GUARDE ESTE MANUAL PARA LAS FUTURAS REFERENCIAS.
NO MANIPULE EL MONITOR SOSTENIENDO POR EL SISTEMA DE ALTAVOCES.
NOTA
Tenga sumo cuidado en el tratamiento de los sistemas de altavoz. Como la delantera de los
sistemas de altavoz es frágil, cuídese de NO empujarla fuertemente ni golpearla.
Componentes del Producto
Especificaciones
Tipo ................................3 altavoces bidireccionales.
Soporte de altavoz (x4)
Altavoces (x2)
Cable de altavoz con núcleo (x2)
Cojín (2)
Tornillo de montaje (x8)
Bass Reflex
Altavoz graves................Tipo cónico de 80mm
x 2/cada uno
Altavoz agudos...............Tipo cúpula 25 mm
Impedancia.....................6 Ω
Potencia de entrada máx. ....50 W
Potencia de entrada RMS ....20 W
Dimensiones externas....101,5 (Ancho) x 635,5
(Alto) x 90,5 (Fondo)
mm/cada uno
Peso ...............................2,1 kg /cada uno
Las especificaciones y diseño están sujetos a
modificaciones sin previo aviso por fines de mejora.
ESPAÑOL
PRECAUCION
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ10
ATENCION
La conexión/desconexión de los cables de altavoz debe realizarse siempre con el interruptor de alimentación del
monitor desconectado (en estado de espera/lámpara de recepción de imagen apagada o encendida en rojo).
Sujete el sistema de altavoces deslizándolo sobre los tornillos aflojados y reinstale los tornillos retirados.
1
Sujete los soportes de altavoz a los sistemas de altavoz.
Sujete los tornillos en una posición que permita leer las marcas de orientación de los soportes de altavoz (R), (L).
En caso de (R)
(R)
(L)
Aviso
Soporte de altavoz
Sobre el cojín.
Tornillo de
montaje X 2
Hay posibilidad de que
se produzca una
pequeña separación
entre la unidad principal
y el sistema de
altavoces.
R
L
Tornillo de montaje X 2
2
3
Esta separación puede Cojín
eliminarse pegando el
cojín suministrado a la
superficie lateral del
sistema de altavoz.
Pegue el cojín
alineando la
superficie delantera
de la caja trasera.
Caja trasera
Soporte de
altavoz
Cojín
Sujete el sistema de altavoces deslizándolo sobre los tornillos aflojados y reinstale los tornillos retirados.
Quite los dos tornillo de cada costado del monitor
tal como se muestra y manténgalos para su
reinstalación. Afloje los dos tornillos de cada
costado del monitor tal como se muestra de
manera que los sujetadores de altavoz puedan
deslizarse sobre ellos. Inserte los tornillos
aflojados en los agujeros de enganche de los
sujetadores de altavoz que están sujetos al
sistema de altavoces, y deslice los tornillos hacia
abajo. Seguidamente, use los tornillos
previamente aflojados para sujetar los sujetadores
de altavoz en los agujeros de montaje del monitor.
Apriete firmemente los cuatro tornillos.
Lado derecho
Sujetador del altavoz
visto de abajo
Quite los
tornillos
Afloje los
tornillos
Quite los
tornillos
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Enganche esta
porción en el
tornillo aflojado
Lado trasero del monitor
Conexión de los cables de
conexión al sistema de altavoces
4
Sujete los cables de conexión de
altavoz al monitor.
Terminales de
altavoz
Tratamiento de los extremos del cable
Quítelos mientras los dobla
- Negro + Rojo
Conecte el cable de color
de cobre al lado +
Conecte el cable de color
de plata al lado -
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Conecte el
cable de color
de plata
Modo de conectar
los cables de
altavoz
(Lado del altavoz)
Empuje hacia
abajo la palanca
con su dedo.
Conecte el
cable de color
de cobre
( ( ) )
Prepare los cables de
altavoz suministrados.
Inserte el
cable.
Quite su
dedo.
Modo de conectar
los cables de
altavoz
(Lado del monitor)
Empuje hacia
abajo la palanca
NOTA
Asegúrese de insertar firmemente los cables de altavoz.
Asegúrese de bloquear firmemente la palanca de los terminales de conexión.
Inserte el
cable
Levante la
palanca
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ11
Högtalarsystem för Hitachi Plasmaskärmar.
Passar till följande modeller: 42PD5000*,42PMA500*,42HDM70,CMP421*
Modell
CMPAS14/CMPAS14S
Användarmanual
Tack för att du köpte detta högtalarsystem för Hitachi Plasmaskärmar.
LÄS INSTRUKTIONERNA I DENNA MANUAL NOGGRANT.
SPARA DENNA MANUAL FÖR FRAMTIDA BEHOV.
FÖRSIKTIGHET
HANDSKAS INTE MED SKÄRMEN GENOM ATT HÅLLA I HÖGTALARSYSTEMET.
Var försiktig vid handskande med högtalarsystemet. Då framsidan på högtalarsystemet är
ömtålig utsätt INTE denna för tryck eller våld.
Innehållsförteckning
Högtalarhållare (x4)
Högtalare (x2)
Högtalarkabel med kärna (x2)
Vibrationsdämpare
(x2)
Monteringsskruvar (x8)
Specifikationer
Typ .................................2 vägs 3 högtalare.
Basreflex
Bashögtalare ..................80 mm typ kärna x 2 /
enhet
Diskanthögtalare ............25 mm kupol typ
Impedans .......................6 Ω
Max. ineffekt...................50 W
RMS ineffekt...................20 W
Utvändiga dimensioner ....101,5 (B) x 635,5 (H)
x 90,5 (D) mm/enhet
Vikt .................................2,1 kg/enhet
Specifikationer och design kan komma att
ändras utan förvarning på grund av
förbättringar.
SVENSKA
Var god beakta följande
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ12
Varning
Högtalarkablarna får endast anslutas/kopplas ur då strömmen till skärmen är av
(Vänteläge/mottagningslampan är släckt eller lyser rött)
Montering av högtalarsystemet på skärmen.
1
Anslut högtalarhållarna till högtalarsystemet.
Vänd högtalarhållarna så att (R), (L) kan läsas korrekt och fäst med skruvarna.
I fallet (R)
(R)
(L)
Information
Högtalarhållare
Om vibrationsdämparna
skruv x 2
Det kan uppstå glapp mellan
skärmen och högtalarna. Använd
de bifogade vibrationsdämparna
för att fylla ut detta glapp genom
att montera dessa på
högtalarsystemet innan montage
på skärmen.
R
L
Högtalarhållare
skruv x 2
2
3
Vibrationsdämpare
Fäst vibrationsdämparna
på sidan av högtalarna
vända mot huvudenheten.
Passa in och fäst
vibrationsdämparna
på framsidan
av bakstycket.
Bakstycke
vibrationsdämpare
Montering av högtalarsystemet på skärmen.
Ta bort de två skruvarna på var sida om
skärmen som bilden visar och spar dem för
senare bruk. Lossa de två skruvarna på var
sida om skärmen som bilden visar så att
högtalarhållarna kan glida ner på dem. Passa
in de lossade skruvarna i anslutningshålen på
högtalarhållarna som är monterade på
högtalarsystemet och skjut ner högtalarna.
Skruva i de tidigare borttagna skruvarna och
fixera högtalarhållarna på skärmen. Dra åt
samtliga fyra skruvar.
Höger sida (R)
Högtalarhållarna
sedda underifrån
Ta bort
skruvarna
Lossa
skruvarna
Ta bort
skruvarna
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Haka denna
sektion på de
lossade skruvarna
Skärmens baksida
Anslutning av högtalarkablar
4
Anslutning av högtalarkablarna till
skärmen
Ände mot högtalare
Vrid och drag loss
- Svart + Röd
Anslut den kopparfärgade
kabeln till + sidan
Förbered kablarnas ändar
Anslut den silverfärgade
kabeln till - sidan
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Anslut den
silverfärgade
kabeln
Hur man
ansluter
högtalarkablarna
(Högtalare)
Tryck ner
handtaget
med ett finger
Anslut den
kopparfärgade
kabeln
( ( ) )
Förbered de bifogade
högtalarkablarna
För in
kabeln
Ta bort
fingret
Hur man
ansluter
högtalarkablarna
(Skärm)
Tryck ner
handtaget
Var god beakta följande
Se till att kablarna förs in ordentligt.
Se till att handtagen på anslutningskontakterna är ordentligt låsta.
För in
kabeln
För upp
handtaget
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ13
Høytalersystemer for Hitachi Plasma skjermmonitor.
Brukermodell: 42PD5000*,42PMA500*,42HDM70,CMP421*
Modell
CMPAS14/CMPAS14S
Brukermanual
Takk for at du kjøpte Hitachi Plasma skjermmonitor
LES INSTRUKSJONENE I DENNE BRUKERVEILEDNINGEN NØYE.
OPPBEVAR DENNE BRUKERVEILEDNINGEN FOR SENERE REFERANSE.
VARSEL
Ikke behandl monitoren ved å holde på høytalersystemene.
Streng aktsomhet
Vær forsiktig med å håndtere høytalersystemene. Da høytalersystemenes forside er lett
skadelig, vennligst ikke behandl på en uaktsomlig måte.
Høytalerholder (x4)
Høytalere (x2)
Høytalerkabel med kjerne (x2)
Puten (2 stk)
Monteringsskrue (x8)
Tekniske Data
Type ...............................2 –veis 3 høytalere.
Bassrefleks
Woofer............................80mm konisk type x
2/hver
Tweeter ..........................25 mm dome-type
Impedans .......................6 Ω
Maks. utgangseffekt .......50 watt
RMS inngangseffekt.......20 watt
Utvendige dimensjoner ......101,5 x 635,5 x 90,5
mm (B x H x D) hver
Vekt ................................2,1 kg hver
Tekniske data og utforming kan bli endret uten
varsel pga. utbedringer.
NORSK
Produktskomponenter
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ14
VARSEL
Høytalerkabelen skal være slått av ved innkobling / utkobling (Ved Standby / mottakerlampen
ikke er på eller når den røde lampen blinker).
Monter høytalersystemene til monitoren.
1
Monter høytalerledningene til høytalersystemene.
Skruene skal monteres når (R) og (L) for høytalerholderens retning vises riktig.
For (H)
(H)
(V)
Melding
Høytalerholder
En liten åpning vil oppstå
ved enkelte tilfeller
mellom legemet og
høytaleren.
Ved gjentetning av
åpningen kan du montere
puten på legemets side.
R
L
Høytalerholder
skrue x 2
2
3
Puten
Om puten
skrue x 2
Tilpass den til
bakhusets forside.
Sett putene i
kant med
bakseksjonens
front og fest dem.
Bakseksjon
Puten
Monter høytalersystemene til monitoren.
Skru ut de to skruene fra begge sider av
skjermen som vist og oppbevar dem for
påmonteringen.
Løsne de to skruene fra begge sider av
skjermen som vist slik at høytalerholderene kan
skyves inn.
Skyv inn de to løsnede skruene inn i
festehullene på høytalerholderene som er
festet til høytalersystemet og skyv skruene ned.
Bruk deretter de tidligere fjernede skruene til å
feste høytalerholderene til skjermen.
Stram fast de fire skruene.
Stram fast skruene.
Høytalerholderen
som vist fra den andre siden
Fjern
skruene
Løsne
skruene
Fjern
skruene
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
Monter denne
delen på den
løsnede skruen
Baksiden av monitoren
Monter koblingskabelen til
høytalersystemet
4
Monter høytalerens koblingskabel til
monitoren
Høytalerterminaler
Behandle trådendene
Trekk ut ved vridning
- Sort
Koble den kobberfarvede
tråden til + side
+ Rød
( )
( )
Koble den sølvfarvede
wiren til - side
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
Koble den
sølvfarvede
tråden
Hvordan koble inn
høytalerkablene
(Høytalersiden)
Trykk ned
spaken med
fingeren din
Koble den
kobberfarvede
tråden
( ( ) )
Vennligst gjør klar de
tilbehørende høytalerkablene.
Putt inn
wiren
Fjern
fingeren din
Streng aktsomhet
Stikk inn høytalerkabelen med sikkerhet
Steng koblingsspaken med sikkerhet.
Hvordan koble
høytalerkablene
(Monitorsiden)
Trykk ned
spaken
Stikk inn
tråden
Trekk opp
spaken
簡体中文
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ15
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ16
繁體中文
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ17
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ18
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ19
日立42V型プラズマディスプレイ専用スピーカーシステム
形名
CMPAS14/CMPAS14S
取扱説明書
このたびは日立プラズマディスプレイ専用スピーカーシステムをお買い上げいただき、まことにあ
りがとうございました。
正しくお使いいただくために、この「取扱説明書」をよくお読みください。
お読みになったあとは、必ず保管してください。
◎ このプラズマディスプレイスピーカーシステムは、CMP421* 専用です。
注意
モニターを移動するときは、スピーカーシステムを持たないでください。
お守りください
スピーカ−システム前面のグリル部を強く押したり、グリル部に衝撃を与えると、スピーカー破損の
恐れがありますので、慎重にお取り扱いください。
スピーカーホルダー(4個)
スピーカー(2個)
スピーカー接続ケーブル
(コア付)(2本)
クッション
(2本)
取付けネジ(8本)
仕様
タイプ ..........................2ウェイ3スピーカ バスレフ型
ウファー.......................80mmコーン型×2個
(左右それぞれ)
ツィータ.......................25mmドーム型
定格インピーダンス ....6Ω
定格入力.......................20W JEITA
最大入力.......................50W 音楽信号ピーク
外形寸法.......................101.5(幅)×635.5
(高さ)×90.5(奥行き)
mm(左右それぞれ)
質量 ..............................2.1kg(左右それぞれ)
改良の為、仕様及びデザインを予告無く変更す
ることがありますのでご了承ください。
日本語
部品構成表
00 42型スピーカー統合-五校 03.9.9 3:39 PM ページ20
注意
スピーカーケーブルは、必ずモニターの電源を切った状態(スタンバイ/受像ランプが消えているかま
たは、赤に点灯している状態)で接続/取り外しをしてください。
モニターにスピーカーシステムを取り付ける
1
スピーカーシステムにスピーカーホルダーを付ける
スピーカーホルダーの向きは(R)
、(L)の表示が正しく読める位置にネジを取り付けます。
(R)の場合
(R)
(L)
お知らせ
スピーカーホルダー
L
スピーカーホルダー
ネジ×2
3
クッションは
スピーカーシステムの
本体側面に貼り付けて
ください。
バックケース
の前側に合わせ
て貼ってください。
本体とスピーカーの間に
すき間が発生する場合が
あります。すき間が気に
なる方は、付属のクッシ
ョンをスピーカーシステ
ムの側面に貼り付けてく
ださい。
R
2
クッション
クッションについて
ネジ×2
バックケース
クッション
スピーカーシステムをモニターに取り付ける
スピーカーシステムに取
り付けた、スピーカーホ
ルダーの引っ掛け穴に緩
めたネジを挿入し下にず
らす。
次に、スピーカーホルダ
ーを本体側固定穴に取り
外したネジで固定する。
(R)の場合
スピーカーホルダー
を下から見た図
ネジを
はずす
ネジを
緩める
この部分を
緩めたネジに
引っかける
モニター後面
スピーカーシステムに接続ケーブルを
取り付ける
4
モニターにスピーカー接続ケーブルを取り
付ける
スピーカーシステム
接続端子
先端処理のしかた
よじりながら抜く
外した
ネジ
SPEAKER TERMINAL
(8Ω8W)
スピーカー端子
(6Ω12W)
−
+
○黒
○赤
+
○赤側に銅色線を接続
−
○黒側に銀色線を接続
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
スピーカー端子
(6Ω12W)
銀色線 銅色線
( )を接続 )
を接続 ( 付属のスピーカー接続ケーブル
を図のように加工してください。
スピーカー
接続ケーブルの
接続方法
(スピーカー側)
レバーを
指で
押したまま
接続ケーブル
を挿入する
指を離す
お守りください
スピーカーケーブルは確実に挿入してください。
接続端子レバーは確実にロックしてください。
QR59021
スピーカー
接続ケーブルの
接続方法
(モニター側)
レバーを
押し下げる
接続ケーブル
を挿入する
レバーを
起こす
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement