ADDENDUM No. 1 to the RFP Document 850-T01

ADDENDUM No. 1 to the RFP Document 850-T01
Town of Taber Page 1 of 1 2017 Projects ADDENDA ADDENDUM No. 1 to the RFP Document 850‐T01 (2017‐43) for Automated Side‐Load Garbage Truck To all Bidders: July 14, 2017 The following changes, additions, and/or deletions are hereby made a part of the RFP documents for the ‘’Town of Taber, Automated Side‐Load Garbage Truck’’ as fully and completely as if the same were fully set forth therein: Schedule “E” – Addendum 1 This Addendum is to reflect the changes to the Schedule “A” of the original document. Please use the attached Schedule “A” to base the proposal. Any other options or add‐ons may be documented on Schedule “B” for consideration. All Bidders shall acknowledge receipt and acceptance of this Addendum by signing in the space provided and submitting the signed Addendum with the Request for Proposal. Proposals submitted without this Addendum may be considered incomplete. Receipt acknowledged and conditions agreed to this _____day of ___________,20__. __________________________________ ______________________________ Bidder Signature Any additional inquires must be submitted no later than EOB, Friday, July 21, 2017. Appended hereto and part of this addendum: End of this Section Addendum 1
SCHEDULE A
SPECIFICATIONS
Proponents shall circle “Yes” or “No” for each specification that is met or not met. Proponents may use
the comments space provided to the right to explain any specifications that are not met or any
specifications that are substantially exceeded.
The truck specifications are a guideline and it is the proponent’s responsibility to ensure all truck
specifications meet the proponent’s engineering requirements, any variation within the truck
specifications must be noted.
Categories / Specifications
Truck Specifications
Complies
Mount unit on a new tandem axle cab and chassis
with setback axle, straight truck provision, Cab – white
powder coat, chassis – black powder coat - SPECIFY
MAKE AND MODEL*include a detailed vehicle
specifications summary with RFP submission
Yes
Vehicle Configuration
Complies
2017/2018 model year specified
Yes
Comments
No
Comments
No
Left hand primary steering location
Yes
No
Terrain/ Duty 90% time spent on paved lanes and 10%
on graveled surfaces
Yes
No
Expected front axle(s) load 14,600 lbs.
Yes
No
Expected rear drive axle(s) load 40,000 lbs.
Yes
No
Expected gross vehicle weight capacity 54,600 lbs.
Yes
No
Engine
Complies
Cummins ISL min 320-330 HP @ 2000 RPM, 2200
GOV RPM, 860 LB/FT @ 1300 RPM
Yes
Electronic Parameters
Complies
68 MPH road speed limit
Yes
No
Cruise control speed limit same as road speed limit
Yes
No
PTO mode engine RPM limit – 1100 RPM
Yes
No
PTO RPM with cruise set switch – 700 RPM
Yes
No
Comments
No
Comments
PTO RPM with cruise resume switch – 800 RPM
Yes
No
PTO mode cancel vehicle speed – 5 MPH
Yes
No
PTO governor ramp rate – 250 RPM per second
Yes
No
Regen Inhibit speed threshold – 5 MPH
Yes
No
One remote PTO speed
Yes
No
Remote PTO speed 1 setting – 800 RPM
Yes
No
PTO minimum RPM - 700
Yes
No
Engine Equipment
Complies
2016 onboard diagnostics/2010 EPA/Carb/Final
GHG17 configuration
2008 carb emission certification – clean idle (includes
6x4 inch label on lower forward corner of driver door)
Yes
No
Yes
No
Standard oil pan
Yes
No
Engine mounted oil check and fill
Yes
No
One piece valve cover
Yes
No
Side of hood air intake with Donaldson high capacity
air cleaner with safety element, firewall mounted.
DR 12V 160 AMP 28-SI Quadra mount pad alternator
with remote battery volt sense
Yes
No
Yes
No
(2) alliance model 1231, group 31, 12-volt
maintenance free 2250 CCA threaded stud batteries
Yes
No
Battery box frame mounted
Yes
No
Standard battery jumpers
Yes
No
Single battery box frame mounted LH side under cab.
Yes
No
Wire ground return for battery cables with additional
frame ground return
Yes
No
Non-polished battery box cover
Yes
No
Positive load disconnect with cab mounted control
switch mounted outboard driver seat
Yes
No
Positive and negative posts for jumpstart located on
frame next to starter
Yes
No
Cummins turbocharged 18.7 CFM air compressor with
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 1 of 25 Comments
internal safety valve
Standard mechanical air compressor governor
Yes
No
Air compressor discharge line
Yes
No
Electronic engine integral shutdown protection system
Yes
No
Cummins exhaust brake integral with variable
geometry turbo with on/off dash switch
Yes
No
RH outboard under step mounted horizontal after
treatment system assembly with RH B-pillar mounted
vertical tailpipe, if different specify for consideration
Yes
No
Engine after treatment device automatic over the road
regeneration and dash mounted regeneration request
switch
Yes
No
11 foot 63-inch (138 inch+0/-5.9 inch) exhaust system
height
Yes
No
RH curved vertical tailpipe B-pillar mounted routed
from step
Yes
No
6 gallon diesel exhaust fluid tank
Yes
No
100 percent diesel exhaust fluid fill
Yes
No
LH medium duty standard diesel exhaust fluid tank
location
Yes
No
Diesel exhaust fluid pump mounted aft of diesel
exhaust fluid tank.
Yes
No
Standard diesel exhaust fluid tank cap
Yes
No
Stainless steel aftertreatment device/muffler/tailpipe
shield
Yes
No
Horton Drivemaster advantage on/off fan drive
Yes
No
Automatic fan control with dash switch and indicator
light, non-engine mounted
Yes
No
Cummins spin on fuel filter
Yes
No
Combination full flow/by pass oil filter
Yes
No
Fleet guard plain coolant filter
Yes
No
1100 square inch aluminum radiator
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 2 of 25 Antifreeze to -34F, oat (nitrite and silicate free)
extended life coolant
Yes
No
Gates blue stripe coolant hoses or equivalent
Yes
No
Constant Tension hose clamps for coolant hoses
Yes
No
Radiator drain valve
Yes
No
Lower radiator guard
Yes
No
Phillips – Temro 1000 watt/115 volt block heater
Yes
No
Phillips – Temro 150 Watt/115 volt oil preheater
Yes
No
Black plastic engine heater receptacle mounted under
LH door
Yes
No
Aluminum flywheel housing
Yes
No
Electric grid air intake warmer
Yes
No
Delco 12v 38MT HD starter with integrated magnetic
switch
Yes
No
Transmission
Complies
Allison 3500 RDS automatic transmission with PTO
provision
Yes
Transmission Equipment
Complies
Comments
No
Allison vocational package 142 – available on
3000/4000 product families with vocational model RDS
Yes
No
Allison vocational rating for refuse applications
available with all product families
Yes
No
Primary mode gears, lowest gear 1, start gear 1,
highest gear 6, available for 3000/4000 product
families only
Secondary mode gears, lowest gear 1, start gear 1,
highest gear 6, available for 3000/4000 product
families only
Yes
No
Yes
No
Primary shift schedule recommended by DTNA and
Allison, this defined by engine and vocational usage
Yes
No
Enhanced converter load release – disabled, available
for all product families only
Yes
No
Primary shift speed recommended by DTNA and
Allison, this defined by engine and vocational usage
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 3 of 25 Comments
Secondary shift speed recommended by DTNA and
Allison, this defined by engine and vocational usage
Yes
No
Load based shift schedule and vehicle acceleration
control recommended by DTNA and Allison, this
defined vocational usage
Yes
No
Neutral at stop – disabled, fuel sense – disabled
Yes
No
Driver switch input – default – no switches
Yes
No
Vehicle interface wiring connector with PDM and no
blunt cuts, at end of frame
Yes
No
Electronic transmission customer access connector
firewall mounted
Yes
No
Chelsea 277 series PTO
Yes
No
PTO mounting, LH side of main transmission
Yes
No
Magnetic plugs, engine drain, transmission drain,
axle(s) fill and drain
Yes
No
Push button electronic shift control, dash mounted
Yes
No
Transmission prognostics – enabled 2013
Yes
No
Water to oil transmission cooler, in radiator end tank
Yes
No
Transmission oil check and fill with electronic oil level
check
Synthetic transmission fluid (TES – 295 compliant)
Yes
No
Yes
No
Front Axle & Equipment
Complies
Detroit DA-F-14.7-3 14,700# FL1 71.5 KPI/3.74 drop
single front axle
Yes
No
Meritor 16.5X6 Q+ cast spider heavy duty cam front
brakes, double anchor, fabricated shoes
Yes
No
Non-asbestos front brake lining
Yes
No
Conmet cast iron front brake drums
Yes
No
Front brake dust shields
Yes
No
SKF Scotseal plus XL front oil seals
Yes
No
Vented front hub caps with window, center and side
plugs - oil
Standard spindle nuts for all axles
Yes
No
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 4 of 25 Comments
Meritor automatic front slack adjusters
Yes
No
TRW TAS-85 power steering
Yes
No
Power steering pump
Yes
No
2 quart see through power steering reservoir
Yes
No
Oil/air power steering cooler
Yes
No
Synthetic 75W-90 front axle lube
Yes
No
Front Suspension
Complies
14,600# taperleaf front suspension
Yes
No
Maintenance free rubber bushings – front suspension
Yes
No
No front suspension spring bracket options
Yes
No
Front shock absorbers
Yes
No
Rear Axle & Equipment
Complies
MT-40-14XP 40,000# R-Series Tandem rear axle
Yes
No
6.14 rear axle ratio
Yes
No
Iron rear axle carrier with optional heavy duty axle
housing
Yes
No
MXL 17N Meritor extended lube main driveline with full
round yokes
Driver controlled traction differential – both tandem
rear axles
Yes
No
Yes
No
(1) Interaxle lock valve, (1) Driver controlled differential
lock forward-rear and rear-rear axle valve
Blinking lamp with each interaxle lock switch, interaxle
unlock default with ignition off, blinking lamp with each
mode switch, differential unlock with ignition off, active
<5 MPH
Meritor 16.5X7 Q+ cast spider cam rear brakes double
anchor, fabricated shoes
Non-asbestos rear brake lining
Yes
No
Yes
No
Yes
No
Yes
No
Brake cams and chambers on forward side of drive
axle(s) with auxiliary support brackets
Conmet cast iron rear brake drums
Yes
No
Yes
No
Rear brake dust shields
Yes
No
SKF Scotseal plus XL rear oil seals
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 5 of 25 Comments
Comments
Heavy duty 30/36 2-drive axles spring parking
chambers
Meritor automatic rear slack adjusters
Yes
No
Yes
No
Synthetic 75W-90 rear axle lube
Yes
No
Rear Suspension
Complies
Airliner 46,000# rear suspension
Yes
No
Airliner high position ride height
Yes
No
Standard axle seats in axle clamp group
Yes
No
Manual dump valve for air suspension with gauge
Yes
No
Indicator light for each rear suspension control switch
Yes
No
Dual air rear suspension leveling valves
Yes
No
Transverse control rods
Yes
No
Rear shock absorbers – one axle (air ride suspension)
Yes
No
Brake System
Complies
Air brake package
Yes
No
Wabco 4S/4M ABS without traction control
Yes
No
Reinforced nylon, fabric braid and wire braid chassis
air lines
Fiber braid parking brake hose
Yes
No
Yes
No
Standard brake system valves
Yes
No
Standard air system pressure protection system
Yes
No
STD U.S front brake valve
Yes
No
Relay valve with 5-8 PSI crack pressure, no rear
proportioning valve
Wabco SS-1200 plus air dryer with integral air
governor and heater
Air dryer mounted under hood
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Steel air tanks mounted AFT inside and/or below
frame just forward or rear suspension
Clear frame rails from back of cab to front rear
suspension bracket, both rails outboard
Pull cable on wet tank, petcock drain valves on all
other air tanks
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 6 of 25 Comments
Comments
Trailer Connections
Complies
Upgraded chassis multiplexing unit
Yes
No
Upgraded bulkhead multiplexing unit
Yes
No
No high current trailer/body cable
Yes
No
Wheelbase & Frame
Complies
5950MM (234 inch) wheelbase
Yes
No
7/16X3-9/16X11-1/8 inch steel frame
(11.11MMX282.6MM/0.437X11.13 inch) 120KSI
Yes
No
¼ inch (6.35mm) C-Channel inner frame
reinforcement
Yes
No
1150MM (45 inch) rear frame overhang
Yes
No
Frame overhang range:41 inch to 50 inch
Yes
No
CALC’D back of cab to rear suspension C/L (CA):
209.45 in
Calculated effective back of cab to rear suspension
C/L (CA) 206.45 inch
Yes
No
Yes
No
Calculated frame length – overall – 349.39 inch
Yes
No
Calculated space available for deck plate 209.45 inch
Yes
No
Calculated frame space LH side 197.09 inch
Yes
No
Calculated frame space RH side 218.66 inch
Yes
No
Square end of frame
Yes
No
Rear Tow Hooks
Yes
No
Front closing crossmember
Yes
No
Light weight heavy duty aluminum engine
crossmember
Yes
No
Standard midship #1 crossmember(s)
Yes
No
Standard rearmost crossmember
Yes
No
Heavy duty suspension crossmember
Yes
No
Chassis Equipment
Complies
Three-piece 14 inch steel center bumper with flexible
plastic ends
Yes
Comments
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 7 of 25 Comments
Comments
Front tow hooks – frame mounted
Yes
No
Bumper mounting for single license plate
Yes
No
Fender and front of hood mounted front mudflaps
Yes
No
Grade 8 threaded hex headed frame fasteners
Yes
No
Fuel Tanks
Complies
60 Gallon/189 liter short rectangular aluminum fuel
tank - LH
Yes
No
Rectangular fuel tank(s)
Yes
No
Plain aluminum/painted steel fuel/hydraulic tank(s)
with painted bands
Yes
No
Fuel tank(s) forward
Yes
No
Plain step finish
Yes
No
Fuel tank cap(s)
Yes
No
Alliance fuel filter/water separator with heated bowl
and primer pump
Yes
No
Equiflo inboard fuel system
Yes
No
High temperature reinforced nylon fuel line
Yes
No
Tires
Complies
Michelin X Works Z 315/80R22.5 20 Ply radial front
tires
Yes
No
Michelin XDE M/S 11R22.5 14 ply radial rear tires or
approved equivalent
Yes
No
Hubs
Complies
Conmet preset plus iron front hubs
Yes
No
Conmet preset plus iron rear hubs
Yes
No
Wheels
Complies
22.5X9.00 10-Hub pilot 5.99 inset aluminum front
wheels
Yes
No
22.5X8.25 10-Hub pilot 2-hand HD steel disc rear
wheels
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 8 of 25 Comments
Comments
Comments
Comments
Front wheel mounting nuts
Yes
No
Rear wheel mounting nuts
Yes
No
Nylon wheel guards front and rear all interfaces
Yes
No
Cab Exterior
Complies
106 inch BBC flat roof aluminum conventional cab
Yes
No
Air cab mounts
Yes
No
Cab roof reinforcements for roof mounted components
Yes
No
Nonremovable bugscreen mounted behind grille
Yes
No
2.5 inch fender extensions
Yes
No
LH and RH grab handles
Yes
No
Painted plastic grille
Yes
No
Stationary black grille with bright accents
Yes
No
Silver hood mounted air intake grille
Yes
No
Fiberglass hood
Yes
No
Hood liner, added firewall and floor heat insulation
Yes
No
Single 14 inch round hadley air horn under LH deck
Yes
No
Single electric horn with shield
Yes
No
Door locks and ignition switch keyed the same with (4)
keys
Yes
No
Dual amber electronic strobe lights with stainless steel
brackets
Yes
No
Integral headlight/marker assembly
Yes
No
LED aerodynamic marker lights
Yes
No
Daytime running lights
Yes
No
Omit stop/tail/backup lights and provide wiring with
separate stop/turn wires to 4 feet beyond end of frame
Yes
No
Standard front turn signal lamps
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 9 of 25 Comments
Dual west coast bright finish heated mirrors with LH &
RH remote
Door mounted mirrors
Yes
No
Yes
No
102 inch equipment width
Yes
No
LH and RH 8 inch bright finish convex mirrors
mounted under primary mirrors
Yes
No
RH down view mirror
Yes
No
Standard side/rear reflectors
Yes
No
Dual level cab entry steps on both sides
Yes
No
Composite exterior sun visor
Yes
No
63X14 inch tinted rear window
Yes
No
Tinted door glass LH and RH with tinted non-operating
wing windows
Yes
No
RH and LH electric powered windows, passenger
switches on door(s)
Yes
No
1 PC tinted roped-in windshield
Yes
No
2 gallon windshield washer reservoir with fluid level
indicator, frame mounted
Yes
No
White winterfront
Yes
No
Cab Interior
Complies
Gray vinyl interior
Yes
No
Molded plastic door panel(s) without vinyl insert with
aluminum kickplate lower door
Yes
No
Black mats with single insulation
Yes
No
Forward roof mounted console with upper storage
compartments with netting
Yes
No
In dash storage bin
Yes
No
Center storage console mounted between the seats
Yes
No
(2) cup holders LH and RH dash
Yes
No
Gray/charcoal flat dash
Yes
No
Smart switch expansion module
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 10 of 25 Comments
2.5 LB. Fire Extinguisher
Yes
No
First aid Kit
Yes
No
Heater, defroster and air conditioner
Yes
No
Standard HVAC ducting
Yes
No
Main HVAC controls with recirculation switch
Yes
No
Standard heater plumbing with ball shutoff valves
Yes
No
Denso heavy duty air conditioner compressor
Yes
No
Binary control R-134A
Yes
No
Premium insulation
Yes
No
Solid-state circuit protection and fuses with spare fuse
kit
Yes
No
12V negative ground electrical system
Yes
No
Dome door activated LH and RH, dual reading lights,
forward cab roof
LH and RH electric door locks
Yes
No
Yes
No
(2) 12 volt power supply mounted in dash
Yes
No
Premium high back air suspension driver seat with 3
chamber air lumbar integrated cushion extension,
forward and rear cushion tilt and adjustable shock
absorber
Premium high back air suspension passenger seat
with 3 chamber air lumbar integrated cushion
extension, forward and rear cushion tilt and adjustable
shock absorber
Dual driver seat armrests and inboard passenger seat
armrest
LH and RH integral door panel armrests
Yes
No
Yes
No
Yes
No
Yes
No
Gray cordura plus cloth driver seat cover
Yes
No
Gray cordura plus cloth passenger seat cover
Yes
No
3 point fixed d-ring retractor driver and passenger seat
belts
Yes
No
Adjustable tilt and telescoping steering column
Yes
No
4-spoke 18 inch (450mm) steering wheel
Yes
No
Driver and passenger interior sun visors
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 11 of 25 Instruments & Controls
Complies
All instrument panel(s) to be gray
Yes
No
Engine remote interface without interlocks
Yes
No
Black gauge bezels
Yes
No
Low air pressure indicator light and audible alarm
Yes
No
(1) single brake application air gauge
Yes
No
2 Inch primary and secondary air pressure gauges
Yes
No
Dash mounted air restriction indicator with graduations
Yes
No
97 DB Back up alarm
Yes
No
Provix Back up sensor
Yes
No
Electronic cruise control with switches in LH switch
panel
Yes
No
Key operated ignition switch and integral start position:
4 position off/run/start/accessory
Yes
No
ICU3S, 132X48 display with diagnostics, 28 LED
warning lamps and data linked
Yes
No
Heavy duty onboard diagnostics interface connector
located below LH dash
Yes
No
2 inch electric fuel gauge
Yes
No
Engine remote interface with preset fast idle
Yes
No
Engine remote interface connector in engine
compartment
Yes
No
Electrical engine coolant temperature gauge
Yes
No
2 inch transmission oil temperature gauge
Yes
No
Engine and trip hour meter integral within driver
display
Yes
No
PTO controls
Yes
No
No lane departure warning system
Yes
No
Electric engine oil pressure gauge
Yes
No
Overhead instrument panel
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 12 of 25 Comments
AM/FM/WB Radio with Bluetooth and microphone,
front USB port, front and rear auxiliary inputs, dash
mounted w/2 speakers in cab.
Yes
No
AM/FM antenna mounted on forward LH Roof
Yes
No
Power and ground studs in/under dash
Yes
No
Electronic KPH Speedometer with secondary MPH
scale, without odometer
Yes
No
Standard vehicle speed sensor
Yes
No
Electronic 3000 RPM Tachometer
Yes
No
No direct connect
Yes
No
Ignition switch controlled engine stop
Yes
No
Two On/OFF rocker switches in the dash with indicator
lights and wire routed to chassis at back of cab, label
OPT
Yes
No
Pre-trip lamp inspection, all outputs flash, with smart
switch
Digital voltage display integral with driver display
Yes
No
Yes
No
Single electric windshield wiper motor with delay
Yes
No
Marker light switch integral with headlight switch
Yes
No
One valve parking brake system with dash valve
control autoneutral and warning indicator
Yes
No
Self-canceling turn signal switch with dimmer,
washer/wiper and hazard in handle
Yes
No
Integral electronic turn signal flasher with hazard
lamps overriding stop lamps
Yes
No
Color/Design
Complies
Cab color – White
Yes
No
Black, high solids polyurethane chassis paint
Yes
No
Standard E coat/undercoating
Yes
No
Body Capacity
Complies
Shall be at least a 20 cu.yd excluding the hopper area
Yes
No
Hopper capacity shall be 6.5 cu.yd
Yes
No
Tailgate capacity shall be 4 cu.yd
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 13 of 25 Comments
Comments
Body Dimensions
Complies
The body is rounded for better resistance
Yes
No
The body is tapered (walls and roof) to facilitate the
unloading of the material and to increase compaction
ratio
Yes
No
Specify dimensions:
Yes
No
Body Floor Construction
Complies
The body floor is rounded
Yes
No
The body floor is a thickness of 0.157 inch
Yes
No
The body floor steel grade is Hardox 450
Yes
No
The body floor yield strength is 175,000 psi
Yes
No
Specify dimensions/thickness/grade:
Yes
No
Body Side Walls Construction
Complies
The body walls are rounded and smooth, improving
resistance and lightness
They are in one piece, full length of the body to reduce
welding seams.
A hinged door is installed to allow operator access to
the hopper on curbside, door on street side not
accepted.
Specify dimensions/thickness/grade/yield strength:
Yes
No
Yes
No
Yes
No
Yes
No
Body Roof Construction
Complies
Body roof is rounded and made of high yield steel for
maximum resistance to stress
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 14 of 25 Comments
Comments
Comments
Comments
Specify dimensions/thickness/grade/yield strength:
Yes
No
Hopper Dimensions and Construction
Complies
The hopper floor is made of abrasion resistant steel
Yes
No
The hopper floor steel grade is Hardox 450
Yes
No
The hopper floor thickness is 1/4 inch
Yes
No
The hopper floor yield strength is 175,000 psi
Yes
No
Specify other dimensions:
Yes
No
Rear Tailgate
Complies
The rear tailgate is operated by 2 hydraulic cylinders.
Yes
No
The rear tailgate is equipped with automatic hydraulic
locks and constant pressure system to allow leak proof
joint.
Tailgate hydraulic line is equipped with flow restrictor
to prevent sudden descent.
Yes
No
Yes
No
A channel mounted rubber seal is installed on the
tailgate to prevent liquid leakage.
The tailgate pivots around a fixed point preventing seal
damage and friction against body.
Yes
No
Yes
No
A cab mounted audible alarm is provided to indicate
when the tailgate is unlocked.
Yes
No
A manual tailgate control with safety protection is
installed in the cab to prevent accidental activation.
Yes
No
One tailgate safety prop is provided.
Yes
No
Tailgate length is 33 inches
Yes
No
Tailgate side and rear thickness is 12 gauge
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 15 of 25 Comments
Comments
Tailgate side and rear steel is ASTM A1011 GR 80
Yes
No
Tailgate side and rear yield strength is 80,000 psi
Yes
No
Specify other dimensions:
Yes
No
Packer
Complies
The packer face is 16” high providing 66,750 lbs. of
force on material.
Yes
No
Packer is operated by 2 single stage, double acting
cylinders.
Yes
No
One complete set of packer controls located in cab is
provided.
Emergency red button is provided to stop packer ram
movement at any time.
Yes
No
Yes
No
Control buttons are industrial type, color coded and
weather resistant.
Yes
No
The packer is guided by 2 rails made of steel grade
Hardox 500
Specify other dimensions:
Yes
No
Yes
No
Hydraulic System
Complies
The hydraulic system is designed to allow easy
maintenance
Yes
No
Hydraulic system is composed of a double Denison
vane pump, one section for the body functions and
one for the arm. Pumps have a common suction port.
Yes
No
The hydraulic pressure body line shall be equipped
with a Denison relief valve R5P, a Denison vent valve
VV01 with a 12 volts DC in line mounted solenoid to
divert the flow back to tank when pump is not
engaged, and a flow control block for system
protection.
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 16 of 25 Comments
Comments
The hydraulic tank is pressurized for pump protection.
Yes
No
The hydraulic tank is equipped with magnetic drain
plug, oil level sight gauge and shut-off ball valve on
suction line.
Yes
No
Return line filter is tank mounted style.
Yes
No
Return filter has a bypass valve and a differential
pressure gauge.
Yes
No
100 mesh suction strainer is installed in tank.
Yes
No
All hydraulic hoses meet SAE standards.
Yes
No
Hydraulic system operates at acceptable temperature
without external cooler.
Yes
No
Quick disconnect fittings are provided so that a
pressure gauge can be easily connected without using
tools or hydraulic fittings removal.
Yes
No
Hydraulic pump model is Denison T6DC
Yes
No
The excess flow back to tank over 45 gpm
Yes
No
Body function pump maximum flow is 20.0 gpm at 700
rpm
Yes
No
Arm functions pump maximum flow is 16.0 gpm at 700
rpm
Yes
No
Hydraulic system pressure relief valve for the body is
2000 psi
Yes
No
Hydraulic system pressure relief valve for the arm is
2100 psi
Yes
No
Hydraulic tank capacity for cab over is 85 gal
Yes
No
Maximum quantity of oil in hydraulic tank is 75 gal
Yes
No
The in tank return line filter capacity is 150 gpm
Yes
No
Specify other dimensions:
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 17 of 25 Automated Arm
Complies
The automated arm is hydraulically operated and
activated by an electro-proportional joystick located in
the cab. 7’ Reach Minimum Needed
Yes
No
The arm is mounted inside the hopper and is protected
by a steel enclosure.
Yes
No
The gripper fingers use rubber straps to adapt to a
wide variety of containers.
Yes
No
An integrated adjustable hydraulic cushioning valve is
used
Yes
No
Shocks on the extension cylinder
Yes
No
Joystick uses contactless Hall effect technology for
better reliability.
Yes
No
Joystick has a Deadman switch to prevent accidental
activation of the arm.
Yes
No
The center of the gripper is offset by a maximum of
24” from the center of the lift pivot point.
Yes
No
The arm is powder coated, high visibility safety yellow
Yes
No
Minimum bin size accepted by lifting mechanism is 32
gallons
Yes
No
Maximum bin size accepted by lifting mechanism is 95
gallons
Yes
No
Maximum lifting capacity at maximum reach is 400 lbs.
Yes
No
Vertical dump height is 91 inches
Yes
No
State options of a Maximum horizontal reach from side
of vehicle 120 inches – 144 inches
Yes
No
Minimum horizontal reach from side of vehicle is 0
inches
Yes
No
Lifting mechanism cycle at minimum reach is 8
seconds
Yes
No
Lifting mechanism cycle time at maximum reach is 22
seconds
Yes
No
Unit weight without grab and oil but including valve is
1990 lbs.
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 18 of 25 Comments
Flow to arm from the flow control is 20 gpm @ 700
RPM
Yes
No
Maximum operating pressure is 2000 PSI
Yes
No
The length of warranty on the automated arm and its
cylinders is 1 year
Yes
No
Specify other dimensions:
Yes
No
Body lifting Mechanism
Complies
The body hoist cylinder is front mounted with outer
cover and top ported.
Yes
No
One safety prop is supplied to support the body in the
raised position.
Yes
No
A light and audible alarm in cab are provided to
indicate when body is raised and remain activated until
it is not completely down.
Yes
No
Body is raised by one single acting front mounted
telescopic cylinder with 4 sections
Yes
No
Body dump angle is 45 degrees
Yes
No
Body lifting cycle time is 70 sec @ 850 RPM
Yes
No
Crusher panel
Complies
An optional crusher panel is installed on the front wall
of the body to optimize the compaction of the material
and to facilitate the transfer into the body
Yes
No
Hydraulic protection is supplied to prevent dumping on
top of the panel
Crusher panel steel grade is A-569
Yes
No
Yes
No
Crusher panel thickness is 3/16 in
Yes
No
Crusher panel dimensions for standard body are 63 x
34 in
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 19 of 25 Comments
Comments
Crusher panel is operated by 1 cylinder, chromeplated
Yes
No
Specify Cylinder dimensions:
Yes
No
Electrical/Pneumatic systems
Complies
All stop, directional, tail and clearance lights are LED
type, recessed mount and water tight
Yes
No
All lights are FMVSS #108 compliant
Yes
No
Rear lights are integrated to tailgate structure
Yes
No
Camera Monitoring System with a 9” Monitor (with 4
cameras as listed below)
Yes
No
A 150 degree backup camera
Yes
No
A camera to be located at the RH arm
Yes
No
A Camera to be located LH pedestrian side
Yes
No
A camera located at the hopper
Yes
No
Limit switches are heavy duty, industrial type, water
tight with adjustable arm
Yes
No
All circuits are protected with resettable circuit
breakers and wiring is color coded and numbered.
Yes
No
Wiring conforms to SAE J1128 and all connections are
sealed with shrink tube
Yes
No
All wiring run in plastic loom
Yes
No
Electrical/pneumatic valves are installed in a watertight
box
Yes
No
All electric wires are run in side rub rails with bolted
access panels for easy access, no wiring under body.
Yes
No
Controls Characteristics
Complies
Tailgate switch is electric
Yes
No
Body lift switch is electric
Yes
No
Pump switch is electric
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 20 of 25 Comments
Comments
Packer controls are electric
Yes
No
Arm joystick is electro-proportional
Yes
No
If the body hydraulic control valve is pneumatic,
electrical/pneumatic control valves will transfer the
signal from the cab control to the body hydraulic
control valve.
Yes
No
Console Standard Characteristics
Complies
All body and arm functions are controlled via a
Canopen network
Yes
No
An LCD display with integrated diagnostic functions is
installed in the cab
Yes
No
Real time operation assistance with continuous
system status on screen
Yes
No
All switches are illuminated.
Yes
No
Accessories
Complies
Mud flaps are supplied at front and rear of rear axle.
Yes
No
Shovel and Tool holder
Yes
No
Optional Tool Box/Boxes Mounted on body where
space is available
Yes
No
Painting
Complies
All parts are properly cleaned of all dirt, grease and
weld slag.
Yes
No
Body, hopper and arm are shot blasted with steel
beads.
Yes
No
One coat of polyurethane primer Imron Elite is applied
on body
Yes
No
One finish coat of polyurethane paint Imron Elite is
applied on body
Yes
No
Finish paint coat is baked. 125°F-150°F
Yes
No
Arm is powder coated, safety yellow
Yes
No
Manuals
Complies
Parts, service and operators manual are supplied for
the refuse packer, cab & chassis as well as on disk or
flash drive.
Yes
No
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 21 of 25 Comments
Comments
Comments
Comments
Lubrication
Complies
All body hinges, cylinder rod ends, cylinder base,
trunnion and pivot points are supplied with grease
fittings.
Yes
Warranty Details
Complies
The body manufacturer is certified ISO 9001
Yes
No
All internal inspection documents such as intermediate
inspection booklets made at the body manufacturer
are available and filed per vehicle.
Yes
No
Warranty on Defective parts: SPECIFY
Yes
No
Warranty on hydraulic cylinders and hoses: SPECIFY
Yes
No
Warranty on automated arm: SPECIFY
Yes
No
Warranty on hydraulic cab & chassis: SPECIFY
Yes
No
Optional warranty (extended) coverage:
SPECIFY
Yes
No
Comments
No
Comments
SCHEDULE B
ADDITIONAL OPTIONS OR ADD-ONS – DO NOT INCLUDE IN PRICING
Options or Add-Ons
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 22 of 25 Costs
SCHEDULE C
PRICING & DELIVERY
Proponent Information (Please Print)
Company Name:
Address:
Contact:
City
Phone:
Province:
Fax:
Postal Code:
Email:
Addenda
The proponent acknowledges the following Addenda have been received. The modifications to the
proposal documents noted therein have been considered and the effects are included in the price.
Addendum Number _____ Dated __________________________________
Addendum Number _____ Dated __________________________________
Addendum Number _____ Dated __________________________________
Make / Model / Year
Total Pricing
* Prices shall exclude GST
****Because this item is included in our 2018 Capital Budget, the Town will not be able to
process payment until January 1st 2018, proponent should may take this into account when
setting their expectant delivery date.
Expectant Delivery Date:
If the delivery date is not met, at the sole and unfettered discretion of the Town, the RFP and Contract may be
cancelled and may be re-issued at a later date or the Town may pick the proponent that was rated second in the
RFP.
Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 23 of 25 SCHEDULE D
REFERENCES
Provide a minimum of five (5) references, preferably with municipal collection experience. We are looking for other municipalities as a reference or contractors that have been contracted for collection of solid waste or recycling. Municipality or Company Name
Person to Contact
Contact Information
We, the undersigned, having examined and read the proposal documents and addenda as issued by
the Town agree to supply the goods, materials or services for the unit prices stated herein.
Signature of Authorized Company Official
Name & Title (Please Print)
FAILURE TO SIGN THE SUBMISSION FORM MAY RESULT IN THE PROPOSAL BEING REJECTED. Automated Side‐Load Garbage Truck Project # 850 – T01 (2017‐43) Page 24 of 25 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising