Hitachi Car Video System lcd monitor User's Manual

Hitachi Car Video System lcd monitor User's Manual
ENGLISH
USER’S MANUAL
Thank you very much for purchasing the HITACHI LCD Monitor.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will
know how to operate the monitor properly. Keep this manual in
a safe place. You will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualified
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
CAUTION
Under no circumstances remove the rear cover of your LCD
monitor.
Never guess or take any chances with electrical equipment of
any kind - it is better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, save
to the extent permitted by law.
LCD Monitor
After the LCD monitor has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is
normal.
Sometimes the screen might have some tiny bright or dark spots.
Please note that this is normal.
CAUTION
To prevent scratches or damages to the LCD screen, do not
knock or rub the surface with sharp or hard objects. Clean the
screen with a soft cloth moistened with warm water and dry with
a soft cloth. A mild soap may be used if the screen is extremely
dirty. Do not use harsh or abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and control panel of the
monitor. When excessively soiled dilute a neutral detergent in
water, wet and wring out the soft cloth and afterward wipe with a
dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or
cracks.
FEATURES
Large-screen, high-definition LCD panel
The 32-inch color LCD panel with a resolution of 1366(H) X
768(V) pixels, creates a high-definition, large-screen (aspect
ratio:16:9) and low-profile flat display. Free from electromagnetic
interferences from geomagnetic sources and ambient power
lines, the panel produces high-quality display images free from
color misconvergence and display distortion.
High Performance Digital Processor
A wide range of input signals can be handed, including
composite, component, and HDMI.
High Definition Digital Processor creates the fine-textured image
with dynamic contrast.
In addition, it corresponds to a broad array of personal computer
signals, from 640 x 400 and 640 x 480 VGA to 1600 x 1200
UXGA. (Analog Input)
Easy-to-use remote control and on screen display
system
The remote control included eases the work of setting display
controls. Further, the on-screen display system, displays the
status of signal reception and display control settings in an easyto-view fashion.
Power saving system
The International ENERGY STAR® power saver feature saves
power consumption automatically when input signals are not
available. When connected to a VESA DPMS-compliant PC, the
monitor cuts its power consumption while it is idle.
Connecting to an Audio Visual Device
• Two composite/S terminals*1, three composite terminals*2, two
component terminals*2 and a HDMI terminal have been added. A
composite video output terminal is also provided as a monitoring
output.
*1 A composite/S terminal = A side input.
*2 If two composite terminal and two component terminal are
used at the same time, the component terminal would govern.
• A wide range of devices can also be connected besides personal
computers.
• A RGB input is possible to switch to component signals from the
Menu screen.
Power Swivel Feature
It allows to turn the LCD monitor left or right within ± 30 degree
using the remote control.
1
ENGLISH
Important
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 3 to 6. Mis-use may cause damage to your
LCD monitor, which could shorten its lifespan, or cause injury to
yourself. Should you encounter any difficulty in the set-up or
operation of your monitor, firstly refer to the Troubleshooting
guide at the rear of this manual.
In the unlikely event of a problem occurring with your LCD
monitor, switch off at the mains sockets, pull out the plugs, and
contact your dealer immediately.
CONTENTS
FEATURES ..........................................................
SAFETY INSTRUCTIONS ....................................
NOTES ................................................................
COMPONENT NAMES .........................................
1
3
7
8
Main Unit ...............................................................................
Remote control ......................................................................
Loading Batteries...............................................................
Handling the Remote Control ............................................
8
9
9
9
INSTALLATION INSTRUCTIONS ...................... 12
Installation ...........................................................................
Anti-tumble measures .........................................................
Connection to an Audio Visual Device ................................
Connecting to a PC .............................................................
Connecting the Speaker Cables ..........................................
Mounting the Side Input ......................................................
Power Cord Connection ......................................................
12
12
13
15
16
17
18
Turning Power On and Off ..................................................
Input Switching ....................................................................
Size Switching .....................................................................
Volume Adjustment .............................................................
Audio Mute ..........................................................................
Power Swivel .......................................................................
Input Signal Screen Display ................................................
Displaying MULTI PICTURE ...............................................
Picture Freezing ..................................................................
Using the Menu Screen .......................................................
SETUP MENU (TV mode) ...................................................
SETUP MENU (Video mode) ..............................................
SETUP MENU
(RGB mode: RGB1 (DVI-PC), RGB2 (RGB)) ......................
FUNCTION MENU ..............................................................
PICTURE MENU (TV/Video mode) .....................................
PICTURE MENU (RGB mode) ............................................
AUDIO MENU .....................................................................
TIMER MENU .....................................................................
LANGUAGE MENU .............................................................
19
20
20
22
22
23
24
25
27
28
29
31
OTHER FEATURES ........................................... 41
Automatic Store ...................................................................
Audio Switching ...................................................................
Power Save Mode ................................................................
DVD Player/ STB Selection .................................................
Signal Check (RGB mode) ...................................................
41
42
43
43
44
TROUBLESHOOTING ....................................... 45
Symptoms That Seemingly Appear to be Failures ............... 45
Actions to Correct Abnormal Displays ................................. 47
PRODUCT SPECIFICATIONS ............................ 48
Signal Input .......................................................................... 49
Recommended Signal List ................................................... 50
OPERATING INSTRUCTIONS ........................... 19
32
34
35
38
39
40
40
Note about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have
any comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the
product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
2
This LCD monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care
must be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the
instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the
user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read
these descriptions thoroughly and fully understand the contents.
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to
incorrect handling.
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to
incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the
left indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to
the left indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements,
cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After
Disconnect the
making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this plug from the
power outlet.
could be dangerous.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where
children are present.
If liquids or foreign objects should enter the monitor, immediately turn off the power switch, disconnect the power plug from
the power outlet and contact your dealer.
•
•
•
•
Do not place the monitor in a bathroom.
Do not expose the monitor to rain or moisture.
Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not
disassemble.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or
electrical shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug
from the power outlet and contact your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical
shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in
damage and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
•
•
•
•
•
•
Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
Do not place anything around ventilation openings of the monitor.
Never block ventilation openings.
Do not put the LCD screen side up.
Do not cover the monitor with a tablecloth, etc.
Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication
on the monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
3
ENGLISH
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the
power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead,
obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value,
type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Surely connect
the ground wire.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the
enclosed power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or
tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them
because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand
holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit from
the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
•
•
•
•
•
•
•
•
•
•
•
Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
Do not allow the battery to be exposed to fire or water.
Avoid fire or high-temperature environment.
Do not hold the battery with metallic tweezers.
Keep the battery in a dark, cool and dry place.
Do not short circuit the battery.
Do not recharge, disassemble or solder the battery.
Do not physically impact the battery.
Use only the battery specified in the manual of this monitor.
Make sure the plus and minus terminals are correctly aligned when loading the battery.
If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse well
with water.
• Obey the local laws on disposing the battery.
4
ENGLISH
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution
in households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Be careful in operating power swivel.
Disconnect the
plug from the
power outlet.
Placing hands or faces near the monitor while operating the swivel function could cause a physical injury or damage.
Use special caution in households where children are present.
PRECAUTIONS
Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
Please avoid installing the monitor directly on the wooden floor. Depending on the quality and the condition of the floor, the monitor
stand may stick to the floor face, and the surface could come off when the monitor is lifted up.
How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
How to clean the LCD screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the LCD screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with
a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh
or abrasive cleaners.
How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
5
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or
changing connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not push the monitor over sideways as transporting it. It may cause damage on the panel glass, increase of the screen defects and/or
damage of the internal fluorescent lamps.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved
stand or legs with the fixings provided according to the instructions.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to
the front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or
has a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for
infirm or handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
6
About screen defects
• High precision technology is used in the making of LCD panels but there may be dark spots (points that do not illuminate) and bright spots
(points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images is displayed. These will disappear in a few minutes
and the display will return to normal. However, if used in high temperatures, it sometimes spends some tens of minutes to return to normal.
Please note this is not a malfunction.
About the panel screen
• LCD screens display images by illuminating fluorescent lamps inside the panel. Because of this, the temperature of the panel surface may
rise in some cases.Also, LCD panels are made of finely processed glass, so please avoid pushing by fingers or hands and giving strong
impact on the panel. It may cause damage to the LC cells, and/or there is danger of glass breakage.
About the power swivel
• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution in
households where children are present. (Refer to Power Swivel shown on 23 )
Using in low temperatures
• The response speed of LCD panel becomes slow as the ambient temperature goes down. This feature may cause residual images in some
cases, but this is not a malfunction. It will return to normal in a while after the temperature becomes normal.
7
ENGLISH
NOTES
COMPONENT NAMES
Main Unit
Front
Panel
Cabinet
(front frame)
Control panel
• Adjustment buttons are located
on the top.
Remote-control receiver
9
Indicating lamp 19
TS
SUB-POWER button 19
• The main power switch is located on the top.
Main power switch 19
VOLUME UP/DOWN buttons 22
( WXADJUST buttons)
Front
CHANNEL UP/DOWN button 20
(STSELECT button)
INPUT SELECT button 20
(OK button)
MENU button 28
Rear
• ( ) indicates the function while the MENU is displayed on the screen.
Rear
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be gripped by
holding the top of the monitor, and the unit should
then be held at the base on both sides for stability
as shown.
• Do not hold the speaker units while moving the set.
The speaker holders may be separated off and the
monitor may fall, and it may result in a physical
injury.
Speaker
terminals
Speaker
terminals
16
16
External device connection terminals
RGB input terminals 15
8
ENGLISH
COMPONENT NAMES (continued)
Remote control
POWER button
RECALL button
FUNCTION SELECT button
DVD CONTROL buttons
INPUT SELECT buttons
MENU button
OK button
FREEZE/RETURN button
SELECT/ADJUST button
PICTURE MODE button
CH I/CH II button (TV)
SOUND MODE button
VOLUME UP/DOWN button
CHANNEL UP/DOWN button (TV)
MUTE button
PROGRAM SELECT buttons
(TV)
MULTI MODE button
MULTI PICTURE button
TV/TEXT button
(TV)
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery cover
in the direction of the arrow.
SWIVEL button
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included
observing the correct polarities.
With in 30 degrees
With in 30 degrees
About 3m
About 3m
About 5m
3. Close the battery cover.
• Replace the battery cover in the direction
of the arrow and snap it back into place.
ATTENTION
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical
injury, or stains.
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
9
COMPONENT NAMES (continued)
Remote control (continued)
FUNCTION SELECT
Press this button to indicate function
mode with a lamp.
*1
DVD and SAT
*2
INPUT SELECT
Press this button to change input mode.
DVD CONTROL
You can use these buttons to operate the
selected brand of DVD player.
SOUND MODE
You may recall the sound mode by
pressing this button. Each time pressed,
sound mode is changed in following
sequence.
Movie
Favorite
RECALL (TV)
With this button, the display change
between “--”, “---”, “-” and AV00 on the
top right hand corner of the screen.
“--” is for 2 digit channel selection, “---”
is for 3 digit channel selection and “-” is
for 1 digit channel selection.
RECALL (Video/RGB)
Press this button to display input signal.
FREEZE/RETURN
Press this button to change the picture
to freeze mode. Press it again to return
to normal picture.
Music
PICTURE MODE
You may recall the picture mode by
pressing this button. Each time pressed,
picture mode is changed in following
sequence.
Speech
CH I/II
This button is for A2 / NICAM models
only.
Dynamic
PROGRAM SELECT
Press these buttons to select a TV
program directly.
Natural
MUTE
Press this button to turn off the set
sound. When press again or the
volume up button, the audio will be
restored.
MULTI MODE
In multi-picture mode, pressing this
button will change the multi-picture
mode.
MULTI PICTURE
Press this button to change the screen
to multi-pictures. Press it again to return
to normal picture.
TIME (TV)
Pressing this button can indicate the
time by On-Screen display when
receiving a TV program on the screen
including TELETEXT service with the
time information.
PHOTO INPUT
These buttons are not available in this
model.
SWIVEL
Press this button to rotate TV. Use
cursor key (
) to select the degree of
rotation.
ZOOM
Press this button can change Picture
size.
*1 FUNCTION SELECT button
This remote control has functions to control other makers of DVD player, DVD Recorder, and Set Top Box as well as this set.
Press the
button to switch between TV, DVD and SAT modes.
Each time the
button is pressed, the indicator will light below the function selected.
For details, refer to 43 .
*2 LED
The LED indicator lamps for DVD and SAT have 2 modes (Lit or blinking).
Lit: Indicates the mode that has been selected. Press the
button to change modes when the LED is lit.
Blinking: Indicates that the maker of DVD or STB can be set. You can set up the maker of DVD or STB while the LED is still
blinking (30 sec). For details, refer to 43
10
Cinema
44 .
ENGLISH
COMPONENT NAMES (continued)
Remote control (continued)
[Buttons for TELETEXT Mode]
PAGE UP / DOWN button
TEXT / TV+TEXT button
INDEX button
CANCEL button
TV / TEXT button
COLOR buttons
(RED, GREEN, YELLOW, BLUE)
REVEAL button
SUB TITLE button
TELETEXT FUNCTION
Buttons on Remote Control
Function
This switches the receiver between the TV mode and the TELETEXT mode.
TV / TEXT
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
TEXT / TV + TEXT
This selects the P100 (100 page).
INDEX
SUB TITLE
CANCEL
RED
GREEN
YELLOW
BLUE
REVEAL
PAGE UP / DOWN
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service
broadcasting).
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the
required text page has been received, the page number will be displayed at the top left of the screen. Press the
CANCEL button again to display the TELETEXT screen.
Each of these buttons selects a link page displayed at the lower part of the screen.
This allows hidden information (found on some teletext pages) to be displayed on the screen.
This button increases / decreases the TELETEXT page number.
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
• Refer to Teletext Language shown on 30
11
INSTALLATION INSTRUCTIONS
Installation
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause
overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no
responsibility for personal injuries or property damage caused by use of other mount units or improper installation.
10cm or more*
CAUTION
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a
desktop setup) or more between the sides and other objects such as walls, etc., so that the
ventilation holes are not blocked.(*)
Cord or chain
Wall or Pillar
Clamp
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall
or pillar.
Cord or chain
Wall or Pillar
Hook
Clamp
Cord or chain
Securing desktop
(1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand
as shown.
(2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
Read SAFETY INSTRUCTIONS (
these steps:
3
to
6
) carefully to ensure maximum safety before proceeding to
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
CAUTION
Loosen a cord or chain enough while operating power swivel to avoid possible troubles.
12
ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Connection to an Audio Visual Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the audio visual device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this device
and the signal output terminal of the audio visual device.
Monitor (rear panel)
Speaker (R)
Power
Cord
To composite
output terminal
To audio output
terminals
To component
input terminals
To component
output terminals
To audio output
terminals
Set-Top Box
Speaker (L)
HDMI*
Antenna
To component To component
input terminals output terminals
DVD Player
VTR
Side Input
Headphone
VTR
To S, composite
audio output terminal
To composite
input terminals
To audio input
terminals
VTR
To composite
output terminals
To audio output
terminals
To S-video
output terminal
To audio output
terminals
DVD Player
[An example of connecting audio visual devices]
• If a component input terminal and a composite input terminal of AV1 and AV2 connect to the monitor at the same time, the component input
would govern.
• If a video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer video quality.
(If an S video input terminal and a video input terminal of AV3 or AV5 (side input) connect to the monitor at the same time, S video input
would govern.)
• If the OUTPUT (Monitor) terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to view the same image as on
the main unit. But it is possible to monitor only the composite video signal from AV1 ~ AV5 input or the S video signal from AV3 and AV5
that is displayed on the screen at the time.
• Secure connecting cables to the stand with the provided clamps.
HDIM*
• HDMI (High-Definition Multimedia Interface) is a digital interface based on DVI (Digital Visual Interface), which is an added function for
audio visual equipment.
- It does not have degradation by transmission since it is digital.
- With only one cable, it is possible to transmit both picture signals and audio signals.
• In case of using analog audio when connecting with DVI-HDMI transformation connector, use analog audio terminal for AV1 input.
13
INSTALLATION INSTRUCTIONS (continued)
Connection to an Audio Visual Device (continued)
Precautions when connecting the antenna
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat
feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the
screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
• For safety, install an external antenna conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable
(not provided) for RF LEADS to reduce the noise.
14
ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "PRODUCT SPECIFICATIONS" concerning the specifications of this device. 48 ~ 52
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output terminal
of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask
the personal computer manufacturer or your local retail dealer.
Monitor (rear panel)
Speaker (R)
Speaker (L)
Power cable
connector
DIGTAL INPUT
RGB 1
Power cord
(DVI)
(D-SUB)
Connecting to a PC Device
3.5 mm
Stereo
mini jack
Connecting to an Audio Visual Device
To signal
output
terminal
(D-sub)
To signal
output
terminal
(DVI)
AUDIO IN
ANALOG INPUT
RGB 2
To audio
output
terminal
To audio
output
terminal
To signal
output
terminal
(DVI)
(Example)
DVD Player
PC
• Setting
RGB1: DVI-PC
RGB2: RGB
For details, refer to 51
• Setting
RGB1: DVI-STB
RGB2: Component
52
For details, refer to 50
51
15
INSTALLATION INSTRUCTIONS (continued)
Connecting the Speaker Cables
CAUTION
Make sure that the main power switch of the monitor is turned off (standby or indicating lamp: off/red) when removing or
connecting the speaker cables.
1. Attach the speaker connecting cables to the monitor. (Make sure the ferrite core is toward the monitor side)
Treating the wire ends
Red
Pull off while twisting
Connect the
red colored
wire
Black
Red
Connect the
red colored
wire
Connect the
red/black
colored wire
Black
Connect the
red/black
colored wire
Please prepare the supplied
speaker cables
Ferrite core
Ferrite core
Twist the heads
How to connect
the speaker
cables
Press down
the lever
Insert the
wire
Release
the lever
2. Attach the speaker cables to speaker systems.
How to connect
the speaker
cables
speaker
terminal
Connect the red/black - colored
wire to the Black side.
Connect the red - colored wire to
the Red side.
16
Hold down
the lever
Insert the
wire
Release
the lever
ENGLISH
INSTALLATION INSTRUCTIONS (continued)
Mounting the Side Input
1. Mount the side input into the speaker holder.
Hook the clamps (4 pieces) of the speaker holder into the holes as shown in the figure and pull them down until it sounds click.
Fasten the side input with the speaker holder by the accessory screw.
Refer to 13 about the connection of side input.
See the below figure how to treat the cable.
Side input
Screw X 1
(Included with side input)
Speaker Holder
Side Input cable
2. Mount the side input into the holder on rear of the monitor.
Fasten the side input with the holder by the accessory screw.
See the below figure how to treat the cable.
Cable strap
Side Input cable
CAUTION
Make sure to secure the power cable and the connecting cables for other audio visual devices, except the speaker connecting
cables, to the clamps and the cable strap of the monitor stand and the rear of it. When the monitor is swiveled, the connectors may
drop out and generate heat. It could cause fire and/or connector failures.Moreover, when wiring up and securing these cables, give
suitable slack not to rub the stand during swiveling or not to block the action of swivel.
[An example of treating the cables]
Bundle the cables
to be secured
Power cord
Connecting
cable
17
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
Connect the power cord, after completing all other connections.
1
2
(1) Connect the power cord to this device.
(2) Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
18
Turning Power On and Off
Indicating lamp
Main power switch
• To turn the monitor power ON, press the main power
switch on the monitor main unit to ON, and then press the
SUB POWER button of control panel or the POWER button
on the remote control.
• To turn the monitor power OFF, press the SUB POWER
button of control panel or the POWER button on the
remote control, and then press the main power switch on
the monitor main unit to OFF.
• During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the POWER button on the remote
control.
Indicating lamp
SUB-POWER button
Indicating
lamp
Power
status
Off
Off
Lights red
Off
(standby)
When the main power switch is ON, and
the POWER button on the remote control
or the SUB POWER button on the upside
of the monitor is OFF.
Lights green
On
When the main power switch is ON, and
the POWER button on the remote control
or the SUB POWER button on the upside
of the monitor is ON.
Off
(Power Save)
When the main power switch is ON, and
the POWER button on the remote control
or the SUB POWER button on the upside
of the monitor is ON.
However, the state is in POWER SAVE
mode.(RGB 1 and RGB 2 only.)
Lights orange
POWER button
Operating
When the main power switch is set to
OFF.
When the indicating lamp lights in orange or the message “No
Sync. Signal”, “Power Save” or “Invalid Scan Freq.” appears on
the screen, there is something unusual about the status of
reception. See “Power Save Mode” or “Symptoms That
Seemingly Appear to be Failures.” 43 44 45
ATTENTION
• Avoid repeatedly turning the monitor on and off at short time
intervals. Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out
of use for an extended period of time.
• If a power failure occurs while the main unit is running, it would
be powered on upon recovery from the failure. Turn off the unit
main power switch before leaving the main unit.
19
ENGLISH
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (continued)
CHANNEL UP/DOWN buttons
INPUT SELECT button
RECALL button
INPUT SELECT
buttons
Input Switching
• Input can be switched by pressing the AV1~6, RGB1 or
RGB2 buttons of the remote control.
CHANNEL
UP/DOWN
button
• Input can be switched to TV by pressing CHANNEL
UP/DOWN button or PROGRAM SELECT buttons.
• Input can be switched in the sequence of TV AV1
AV2 AV3 AV4 AV5 AV6 RGB1 RGB2 by
pressing the INPUT SELECT button of the control panel.
TV
AV1
RGB2
RGB2
AV2
AV3
PROGRAM
SELECT
buttons
AV4
RGB1
RGB1 AV6
AV6 AV5
AV5
Size Switching
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the screen.
ZOOM button
• During TV/VIDEO signal input (AV1, AV2, AV3, AV4, AV5,
AV6, RGB1(set to [DVI-STB])and RGB2(set to [Component]))
Panoramic
Zoom
Full
Cinema
• The size will fix as Full mode and not change when receiving the
component signal of 1080i/50, 1080i/60 or 720p/60.
4:3
Full
Display size selection diagram
When you want to
Play a 4:3 image in a 16:9 screen faithfully.
Set the display size to
Input signal
4:3
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the screen
enlarged on equal scales and with both sides
appearing somewhat enlarged.
Panoramic
Play a 16:9 VISTA size image in the 4:3 image
faithfully reproduced on the 16:9 screen.
Zoom
Remarks
Blanking occurs on both sides.
(4:3 signal)
(Vista)
Play a 21:9 Cinema size image in the 4:3
image expanded vertically on the 16:9 screen.
Display screen
• The 4:3 image is called a letterbox
image.
• In some cases, some slight blanking may
remain at the top and bottom.
In some cases, some slight blanking may
remain at the top and bottom.
Cinema
(Cinema)
Play a 4:3 image faithfully in a 16:9 screen in
the standard vertical size and horizontally
squeezed.*
20
Full
(Squeeze)
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a
4:3 screen
ENGLISH
OPERATING INSTRUCTIONS (continued)
Size Switching (continued)
Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows.
1. Press ZOOM button and
SELECT buttons during picture size display.
2. Position display will appear.
3. Adjustment range of each picture size are as shown below.
[Panoramic]
- 12 to + 12
[Zoom] and [Cinema]
- 31 to + 31
4. When 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position + 31
Position - 31
Press
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV
program, the image would appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or public viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
• During RGB Input (RGB1 (set to [DVI-PC]) and RGB2 (set to [RGB]))
Normal
Full
Zoom1
Real
Zoom3
Zoom2
* Real mode gives the image of the same shape as it is displayed on a computer monitor.
This mode is only available for VGA (640 X 480), WVGA (864 X 480),SVGA (800 X 600),XGA (1024 X768) and WXGA (1280 X768).
Display area selection diagram (RGB input)
Resolution
Full display
Display
Full
Circular display
Normal
Real
Zoom1
Zoom2
Zoom3
640 X 480
(VGA)
800 X 600
(SVGA)
1024 X 768
(XGA)
1280 X 1024
(SXGA)
1600 X 1200
(UXGA)
1366 X768
(WXGA)
Selected
character
WXGA Type
can’t select
32
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a
possibility that flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical
Filter On 33 can reduce the flicker.
21
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
Audio Mute
The volume can be adjusted by pressing the
buttons of the remote control (or the
and
buttons of the monitor unit).
and
volume
Volume setting value
Adjustment status guide display
• When a button is pressed, the volume adjustment status
guide will be displayed.
• The volume will increase when the
the guide is being displayed.
• The volume will decrease when the
the guide is being displayed
button is pressed while
button is pressed while
The audio volume can be temporarily muted by pressing the
MUTE button of the remote control.
Volume setting value
Adjustment status guide display
(The display color will change to magenta : volume → Mute)
• When a button is pressed, the volume adjustment status
guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the
button
while the audio is mute.
• The muting can be cancelled by pressing the
button or
MUTE button while the audio is mute.
• The audio from the headphone terminal is not mute.
• The audio from the speaker is automatically mute while
connecting the headphone to the headphone terminal of the
side input (AV5).
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
22
ENGLISH
OPERATING INSTRUCTIONS (continued)
Power Swivel
• This feature controls the motorized stand. It allows turning the LCD monitor left or right using the remote control.
WARNING
Make sure that the main power switch of the monitor is turned off when removing or connecting the power cord, the connector
cables, and the speaker cables.
1. Press Swivel button.
The controlling icon appears on the screen.
• If the connecting cable is not connected, the indication "Not Available" appears.
• The swivel display disappears in about 6 seconds without any operation.
Swivel
2. Adjust for preferred angle.
Opposite directions are displayed on the screen while the monitor is swiveled.
Adjust by using
key while the swivel display is on the screen.
Swiveling angle of the monitor is available within ±30 degrees from the front face.
ATTENTION
• Do not push the panel manually while using the swivel function. It could cause damage to the stand or the panel.
• Do not get on and hang from the monitor. Do not swing the monitor back and forth and around either. It could cause a failure of the
stand.
• Do not put hands or faces close to the monitor while operating the swivel function. It could cause a physical injury. Use special caution
in households where children are present.
• Do not put any object, like a vase, near the monitor in swiveling area. It would cause a breakage of the object and /or a failure of the
stand.
• Place the monitor on the stable location, or the swivel function would not operate correctly. It would cause a malfunction.
• In the case of using the monitor wall mounted, be sure to detach the connecting cable between the monitor and the stand.
Caution when connecting the monitor with the stand
• When detaching the stand from
the monitor, make sure to
detach the connector cable from
the stand connection terminal on
the rear of the monitor.
• When attaching the stand to the monitor
once again, insert the connector cable
into the stand connection terminal on the
rear of the monitor.
Pinch right and
left locks of the
connector and pull
out downward.
Insert until it clicks.
• Make sure that the direction of the connector for stand connecting cable is correct.
23
OPERATING INSTRUCTIONS (continued)
Input Signal Screen Display
The input signal status can be displayed on the
screen by pressing the RECALL button of the
remote control.
• The display will go out in approximately 6 seconds.
RECALL button
TV
Off-timer
On-timer
1
ABCDE
OFF
ON
-- -- Min.
-- -- : -- --
VIDEO
Off-timer
On-timer
RGB
Off-timer
On-timer
24
AV1
Composite
OFF
ON
TV position
Name
Sound mode
Input mode
Signal mode
-- -- Min.
-- -- : -- --
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
ENGLISH
OPERATING INSTRUCTIONS (continued)
RECALL button
INPUT SELECT
buttons
SELECT/ADJUST
button
( , , , )
CHANNEL
UP/DOWN button
Displaying MULTI PICTURE
MULTI MODE
button
MULTI PICTURE
button
When the MULTI PICTURE button on the remote control is
pressed, the screen will display the multi pictures. And then
three types of the screen can be selected by pressing the
MULTI MODE button on the remote control.
The multi-picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the and SELECT buttons; the audio will
be output from the side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be
selected by pressing INPUT SELECT buttons on the remote control.
• Pressing the MULTI PICTURE button once again will cancel the multi-picture mode.
• Refer to the table for 2 pictures (Split) mode. 26
5
A
AV 1
B
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
• Press and SELECT buttons to select picture A or picture B indicated by a red triangle. For pictures
on right, press
and
SELECT buttons to select picture. The selected input display number would
change green.
• The TV channel can be changed by pressing the CHANNEL UP/DOWN button on the remote control.
• The audio can only be output from picture A in 4 pictures mode.
• The component signal input mode cannot be selected in pictures B. Refer to the table for 4 pictures
mode. 26
5
A
B1
8
B2
6
B3 11
• Pressing the MULTI PICTURE button at the 4 pictures mode will cancel the multi-picture mode. And then,
pressing the MULTI PICTURE button again will display the 4 pictures.
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
•
•
•
•
Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
This function activates only in TV mode.
After several seconds, it refreshes the picture one by one.
Pressing the MULTI PICTURE button at the 12 pictures mode will cancel the multi-picture mode. And
then, pressing the MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button at the 12 pictures mode will display the 2 pictures (Split) mode.
25
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE (continued)
Activating the Split mode from the video input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
AV1
• The speaker icon can be shifted left and right by pressing the and SELECT buttons. The audio of the
video will be output from the side on which the speaker icon is located.
• The same video input mode cannot be selected for both screens at the same time.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• Refer to the table for 2 pictures (Split) mode.
AV2
Activating the MULTI PICTURE mode from the RGB input screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• This mode can be available from RGB1 (DVI-PC) and RGB2 (RGB) input.
• The speaker icon can be shifted up and down by pressing the and SELECT buttons. The audio will
be output from the side on which the speaker icon is located.
and
SELECT buttons.
• The sub-screen position can be selected up and down by pressing
• The sub-screen can be selected with the AV1~AV6, TV channel buttons from the status that the speaker
icon appears on the left side of AV¾ etc. as shown in the diagram to the right.
• Pressing the MULTI PICTURE button again will cancel the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when sub-screen is the component signal of
1080i/50 or 1080i/60.
AV1: Displays the VIDEO input signal of the sub-screen.
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not
change to power save mode.
2 Pictures (Split)
Input terminal
AV1 ~ AV5
Sub
Main
TV
PAL
SECAM
NTSC3.58
NTSC4.43
AV1, AV2,AV6
576i
576p
480i
480p
1080i/50 1080i/60
720p/60
TV
{
{
{
{
{
{
{
{
PAL, SECAM
{
{
{
{
{
{
{
{
NTSC3.58/4.43
{
{
{
{
{
{
{
{
576i, 576p
{
{
{
{
{
{
{
{
AV1
480i, 480p
{
{
{
{
{
{
{
{
AV2
1080i/50
{
{
{
{
{
{
{
{
AV6
1080i/60
{
{
{
{
{
{
{
{
720p/60
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
AV1 ~ AV5
RGB1
STB
RGB2
Component
RGB1
RGB2
STB
Component
TELE
TEXT
Main
Sub
{
({ : Available)
Teletext is available only for TV
4 Pictures
Input terminal
AV1 ~ AV5
Sub
TV
PAL
SECAM
NTSC3.58
NTSC4.43
TV
{
{
{
Main
AV1 ~ AV5
AV1, AV2,AV6
576i
576p
480i
480p
1080i/50 1080i/60
RGB1
720p/60
STB
RGB2
Component
TELE
TEXT
Sub 1
Sub 2
PAL, SECAM
{
{
{
NTSC3.58/4.43
{
{
{
576i, 576p
{
{
{
AV1
480i, 480p
{
{
{
AV2
1080i/50
{
{
{
AV6
1080i/60
{
{
{
720p/60
{
{
{
{
{
{
RGB1
STB
RGB2
Component
Sub 3
({ : Available)
26
Main
ENGLISH
OPERATING INSTRUCTIONS (continued)
FREEZE button
Picture Freezing
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the
“Freeze Mode” setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and
the other still.
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze
function as below:
Split
Strobe
TV
O
O
O
PAL. SECAM
O
NTSC3.58/4.43
O
O
576i
O
O
480i
O
O
576p
O
480p
O
1080i/50
O
1080i/60
O
720p/60
O
[Split]
5
A
B
[Strobe]
RGB. DVI-PC
( O : Available )
27
OPERATING INSTRUCTIONS (continued)
RECALL button
MENU button
OK button
RETURN button
SELECT/ADJUST
button
( , , , )
Using the Menu Screen
(On-screen display system)
When the MENU button is pressed, the adjustment menu screen
will be displayed; from there, several adjustments and settings
are possible by using the SELECT button, ADJUST button and
OK button.
• Refer to 29 - 41 concerning the adjustment items and the
settings.
Example: Selecting the Picture screen from TV/Video mode
1. Press the MENU button to display the Main Menu screen.
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
2. Press the OK button to display the Picture Menu screen.
(Use the
and
SELECT buttons to select other items.)
OK
Picture
Picture Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Contrast Mode
Back Light
Reset
Select
Return
:
:
:
:
:
:
:
:
:
Dynamic
+ 31
– 31
0
0
+ 31
Normal
Normal
+ 20
Reset
Exit
3. Use the
and
SELECT buttons to select the item to be
adjusted and then use the and ADJUST buttons to
adjust (example: Contrast).
Contrast
Next / Prev
+ 31
Adjust
Return
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the Adjustment
Menu screen will be closed automatically.
28
ENGLISH
OPERATING INSTRUCTIONS (continued)
SETUP MENU (TV mode)
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Off
Return
Off
Return
Setup
Manual Tuning
Position
Frequency
Name
Sound System
Color System
Skip
Off
NR
Antenna Att.
Select
Return
Setup
Fine Tuning
Select
Setup
Auto Tuning
Mode
Search
Select
Position
Set
Return
Off
Off
Exit
Prog.No.199
+56
Return
Setup
Auto Tuning
Mode
Search
Select OK Set
Position
Return
Off
Return
Off
Return
Setup
Sort
Position
100
101
102
103
104
105
106
107
Select
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Teletext Language
Auto Off
Select OK Set
Adjust
99
250MHz
ABCDE
BG
Auto
Name
ABCDE
BBC1
----BBC
FGHIJ
XYZAB
---------
Setup
Auto Tuning
MHz
62MHz
83MHz
97MHz
106MHz
175MHz
189MHz
199MHz
225MHz
Return
Scanning Channel Number: 33
Cancel
OK
Cancel
Exit
Setup
Teletext Language
West Europe
East Europe
Cyrillic
Greek/Turkish
Off
Return
Select
Return
Exit
29
OPERATING INSTRUCTIONS (continued)
SETUP MENU (TV mode) (continued)
Selected characters
W
X
Setup hint
Auto Tuning
Select the channel entry method between position setting or direct setting.
And press the OK button to fix it.
• If [Position] is selected, the screen display will be numbers (1~199 and
AV00).
• If [Direct] is selected, the screen display will be C** at the channel 0~99
and S** at the channel 100~199.
Mode
Search
Press the OK button and it starts the auto tuning.
Manual Tuning
Set the position number (1~199 and AV00) or channel number (C**, S**) by
( + ) ( - ) CHANNEL UP/DOWN button.
Position
• If [Position] has been selected, search the frequency here by pressing
W and X buttons.
• If [Direct] has been selected, this function will be not available (grayed out).
Frequency
This is used to input the name of the TV station within 5 letters. After fixing
the cursor on the first digit, select a letter by T and S SELECT buttons and
move to next digit by X ADJUST button. Press the OK button again after
finished.
• Selectable letters are “0”~`”9”, ”A”~`”Z”, “+”, “–”, ” ”(blank), ”,”(comma) and
”.”(period).
Name
Sound System
Select the sound system through the 5 different settings.
Color System
Select the color system through the 5 different settings.
If this is set to On, that position will be skipped while selecting positions by
CHANNEL UP/DOWN button.
This is automatically set to On for those non-broadcasting channels.
Skip
NR
If this is set to On, it helps to reduce the noise interference visible on the
screen, especially in the weaker signal reception areas.
Antenna Att
If this is set to On, it helps to reduce the noise inter ference visible on the
screen in case of strong airwave.
Fine Tuning
Decreasing the frequency data
for the main tuner
Increasing the frequency data for
the main tuner.
After completing the fine-tuning, press the RETURN button to exit this mode.
• The variable range is -56 ~ +56.
Sort
(When the Mode in Auto Tuning menu is set to [Direct], this function will be not available (grayed out).)
(A Line of position List)
Press OK button at a line that is required to change order, then the
characters will change to green. And move it up or down in the list by
pressing S and T SELECT buttons. And press OK button to complete it.
Press the RETURN button to exit.
Teletext Language
Select the teletext language, depending on the area utilized, through the 4
settings; West Europe, East Europe, Cyrillic and Greek/Turkish.
• Select West Europe when watch in Singapore, Australia, Malaysia, and so
on.
Auto Off
If this is set to On, the power will be turned off when there is no transmission
signal and no operation for about 10 minutes in the TV mode.
30
ENGLISH
OPERATING INSTRUCTIONS (continued)
SETUP MENU (Video mode)
Selected characters
Setup hint
Do not change the original setting.
(System1: Europe/Asia, System2: North America)
System
Color System
System1
AV1~AV5
System2
This should correspond to the color system of the signal from the
equipment that is connected to AV1~AV5 video input terminal.
• Normally, set this to Auto. The system of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
• When the component signal is received, this would be not available
(grayed out).
Video Input
AV1, AV2
This should correspond to the signal mode of the signal from the
equipment that is connected to AV1, AV2 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
RGB1
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
RGB2 (1st step)
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
RGB2 (2nd step)
This step should be set only when [Component] is selected on the 1st
step.
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and
the operation is found erratic, set this to match the input signal.
31
OPERATING INSTRUCTIONS (continued)
SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB))
Selected characters
Setup hint
Adjust
Pressing the OK button here,
Automatic regulation is started.
Auto Adjust*
Moves the horizontal position to left.
Moves the horizontal position to right.
Adjust the left-side display position.
Screen display changes to Magenta color if beyond the available
range. (This function is only for RGB2. It’s not available (grayed
out) for RGB1 (DVI-PC).)
Moves down the vertical position
Moves up the vertical position.
Adjust the vertical display position.
Screen display changes to Magenta color if beyond the available
range. (This function is only for RGB2. It’s not available (grayed
out) for RGB1 (DVI-PC).)
Reduces the dot clock frequency
(shrinks the right side).
Increases the dot clock frequency
(expands the right side).
Slows the dot clock phase (shifts
slightly to left).
Advances the dot clock phase (shifts
slightly to right).
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
(off the function)
Adjust for clear character visibility.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1 (DVI-PC).)
The original factory settings for the items of this Menu page can
be restored by pressing the OK button.
Set this to Off if the frequency information of the Input Signal
Screen Display is not required.
Frequency Display
This is only available for W-VGA signal.
When it is set to On, the display area mode can be selected Full
or Real. (With RGB1 INPUT, the screen remains the same. RGB2
(ANALOG) INPUT only)
WVGA Type
32
(waiting to reset)
Adjust for maximum character clarity.
(This function is only for RGB2. It’s not available (grayed out) for
RGB1 (DVI-PC).)
Normally set to 0.7 V. If white is found to spread across the
screen, set to 1.0 V. (This is effective only for RGB2.)
Input Level
WXGA Mode
Horizontal Position. Vertical Position. Horizontal Clock and Clock
Phase are adjusted automatically.
O ff
This is only available for W-XGA signal.
(RGB2 (ANALOG) INPUT only)
ENGLISH
OPERATING INSTRUCTIONS (continued)
SETUP MENU (RGB mode: RGB1 (DVI-PC), RGB2 (RGB)) (continued)
Selected characters
Setup hint
Vertical Filter
Frequency Mode
Turn On when concerned about screen flicker.
Grayed out
This function is not available.
RGB1
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB1 DVI terminal.
RGB2 (1st step)
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
RGB2 (2nd step)
This step should be set only when [Component] is selected on the
1st step.
This should correspond to the signal mode of the signal from the
equipment that is connected to RGB2 D-sub terminal.
• Normally, set this to Auto. The signal mode of the input signal
will be automatically recognized.
• If the input signal contains much noise or has a low level at
Auto and the operation is found erratic, set this to match the
input signal.
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
33
OPERATING INSTRUCTIONS (continued)
FUNCTION MENU
Selected characters
Setup hint
This moves the picture around the screen in small amounts, at set
intervals, to reduce the residual image. This is where stationary objects,
such as screen logos, leave a slight image visible after they should have
disappeared.
Screen Saver
Screen Wipe
On
60Min.
This is used to reduce the residual image that can occur with stationary
pictures by the white field signal. Select On (continuous operation) or 60
Min. (time limit operation) and press the OK button. Press the MENU or
RETURN button on the remote control to return to normal viewing.
Black Side Panel
This turns the gray sidebars to the black sidebars when watching normal
mode screen size area. It is always set to Off when the monitor powered
On. It is recommended to set to Off to reduce the residual image.
Video Power Save
This is used to reduce power consumption for video input when there is
no video signal. Setting it On will lead the monitor to the standby mode
when the AV input with no signal is selected.
Freeze Mode
This selects the display condition of the FREEZE mode between Split (2
pictures) and Strobe (12 pictures).
Default Zoom
This selects the screen display size of TV input that appears first when
the main power turned on.
Reset
34
(off the function)
(waiting to reset)
This original factory settings for the items of this Menu page can be
restored by pressing the OK button.
ENGLISH
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (TV/Video mode)
35
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (TV/Video mode) (continued)
Selected characters
Setup hint
Dynamic: This setting is best for very bright ambient lighting.
Natural: This setting is for normal lighting conditions.
Cinema: This setting is best for watching movie.
Picture Mode
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding SELECT
button at [+31]. The color for [+32] to [+40] numbers will change from
green to magenta. This special mode is better for dark scenes.
For normal viewing we recommend that the Contrast is set to [+31].
Brightness
Black is subdued for increased
overall darkness.
Black is set off for increased overall
brightness.
Adjust to preference.
Color
Decrease color intensity.
Increase color intensity.
Adjust to preference.
Sharpness
Soft
Sharp
Shift to the minus (-) side for a softer effect and plus (+) for sharper
picture.
Tint
Enhances red and weakens green.
Enhances green and weakens red.
This is not available to adjust when receiving PAL/SECAM signal.
Then the character will be grayed out.
Adjust for the most realistic skin color.
Color Temperature
Normally set to Cool.
Contrast Mode
Dynamic: Emphasizes the differences between video shadings to
improve the feeling of contrast.
Normal: The gradation of an image is reproduced as faithfully as
possible.
Auto: Detects image brightness and automatically adjusts for natural
brightness.
Back Light
Darkens the screen.
Brightens the screen.
Adjust to preference (for the maximum visibility).
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
YNR
Performs picture signal noise reduction. Turn up to reduce noise.
CNR
Performs color signal noise reduction. Turn up to reduce noise. And it
will be fixed as Off only when selecting DVI-STB mode.
Film Mode
On: Automatically detects the movie film material and faithfully
reproduces the original film image.
Off: Set to OFF when switching between images does not appear
natural.
PAL Comb Filter
This is available only when receiving a PAL composite signal. Turn On
to reduce the discolorations in fine picture detail and provides purer
color.
LTI
Adjusts the sharpness of the picture signal.
CTI
Adjusts the sharpness of the color signal.
Black Enhancement
Adjusts the black level compensation.
Auto Color
This is available only when receiving an NTSC composite/S.Video
signal. This monitors and adjusts the color to maintain constant color
levels. It also maintains natural flesh tones while preserving fidelity of
background colors.
Color Temp. Adjustment
Turn On when you wish to change color temperature depending on the
user’s preference.
Amplitude
Cut Off
Red
Brighter scene is decreased in
reddish color.
Brighter scene is increased in
reddish color.
Green
Brighter scene is decreased in
greenish color.
Brighter scene is increased in
greenish color.
Blue
Brighter scene is decreased in
bluish color.
Brighter scene is increased in
bluish color.
Red
Dark scene is decreased in reddish
color.
Dark scene is increased in reddish
color.
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Dark scene is decreased in bluish
color.
Dark scene is increased in bluish
color.
Green
Blue
36
Adjust color temperature depending on the user’s preference. These
settings are independently stored in each of the 4 Color Temperature
modes.
ENGLISH
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (TV/Video mode) (continued)
Selected characters
Setup hint
Turn On when the original balance of each color is required to adjust
depending on the user’s preference.
Color Management
Magenta
Magenta is weakened.
Magenta is strengthened.
Red is weakened.
Red is strengthened.
Yellow
Yellow is weakened.
Yellow is strengthened.
Green
Green is weakened.
Green is strengthened.
Cyan
Cyan is weakened.
Cyan is strengthened.
Blue
Blue is weakened.
Blue is strengthened.
Red
This adjusts listed colors individually to make them either deeper or
purer. These settings are independently stored in each of the 4 Color
Temperature modes.
Select the single color screen when that is required to adjust R/G/B level
individually depending on the user’s preference. And set it back to RGB
mode that indicates all color after adjusting.
Press the OK button every time the setting is changed.
Color Decoding
Red
Darkens red only.
Lightens red only.
Green
Darkens green only.
Lightens green only.
Color
Decreases color Intensity .
Increases color Intensity.
Tint
Enhances red and weakens
green.
Enhances green and weakens
red.
This adjusts R/G/B level or tint to make the color appear natural for the
user’s preference. These settings are independently stored in each of the
4 Color Temperature modes.
When select "Tint", the display will be gray to indicate that it is not
available when receiving PAL/SECAM signal.
37
OPERATING INSTRUCTIONS (continued)
PICTURE MENU (RGB mode)
Selected characters
Setup hint
Adjust for maximum visibility to suit the ambient brightness.
This can adjust further till [+40] by pressing and holding SELECT
button at [+31]. The color for [+32] to [+40] numbers will change from
green to magenta. This special mode is better for dark scenes.
For brighter scene some parts of the picture might not be clear.
We recommend to set at [+31].
Contrast
Narrows the gap between
brightness and darkness.
Broadens the gap between
brightness and darkness.
Brightness
Black is subdued for increased
overall darkness.
Black is set off for increased
overall brightness.
Adjust to preference.
Color
Decreases color intensity.
Increase color intensity.
Adjust to preference.
Tint
Enhances red and weakens
green.
Enhances green and weakens
red.
This is not available to adjust when receiving PAL/SECAM signal.
In this case the character will be grayed out.
Adjust for most realistic skin color.
Picture Enhancement
Sets the clarity of small details to the desired level.
Color Temperature
Normally set to Normal.
Color Temp. Adjust
Turn On when you wish to change color temperature is required to
adjust depending on the user’s preference.
Red
Brighter scene is decreased in
reddish color.
Brighter scene is increased in
reddish color.
Green
Brighter scene is decreased in
greenish color.
Brighter scene is increased in
greenish color.
Blue
Brighter scene is decreased in
bluish color.
Brighter scene is increased in
bluish color.
Red
Dark scene is decreased in
reddish color.
Dark scene is increased in
reddish color.
Green
Dark scene is decreased in
greenish color.
Dark scene is increased in
greenish color.
Blue
Dark scene is decreased in
bluish color.
Dark scene is increased in
bluish color.
Back Light
Darkens the screen.
Brightens the screen.
Adjust to preference (for the maximum visibility).
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Amplitude
Cut Off
38
Adjust color temperature depending on the user’s preterence. These
settings are independently stored in each of the 4 Color Temperature
modes.
ENGLISH
OPERATING INSTRUCTIONS (continued)
AUDIO MENU
Selected characters
Setup hint
Movie: This selects the audio suitable for Movie.
Music: This selects the audio suitable for Music.
Speech: This selects the audio suitable for News, Talk show etc.
Favorite: This mode should be adjusted depending on user’s
preference.
Audio Mode
Treble
Suppresses treble.
Enhances treble.
Adjust to preference.
Bass
Suppresses bass.
Enhances bass.
Adjust to preference.
Balance
Suppresses right-side sound.
Suppresses left-side sound.
Adjust to preference.
Dynamic Bass
Dynamic Bass takes advantage of the ability of the human ear to be
able to distinguish between two different tones. By using this ability,
Dynamic Bass gives enhanced bass sound that otherwise would not
be heard. Adjust it depending on the user’s preference.
Matrix Surround
This features the spacious sound effects of a stadium.
Perfect Volume
This will automatically adjust volume so each channel and input has
the same average volume level.
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
Headphone Volume
Turns down the volume.
Turns up the volume.
This is to set the volume for headphone. The audio from the speaker is
mute when connected to headphone terminal.
Headphone Select
A/B: During the 2 pictures mode, the audio will be output from
headphone on the screen which is selected between A (left
picture) or B (right picture). The speaker icon is located on the
selected picture.
B:
The audio of B (right picture) is output from headphone.
NOTE
About the Headphone
• During PC input (RGB1/RGB2), the audio is not output from the headphone.
• Only with AV1 and AV6 inputs during the 2-pictures mode, even though select “B” from “Headphone Select”, the audio of A (left picture)
is always output from the headphone.
39
OPERATING INSTRUCTIONS (continued)
TIMER MENU
Selected characters
Setup hint
This function automatically sets the power to standby status when the
indicated time period has elapsed.
Off Timer
On Timer
hours
minutes
LANGUAGE MENU
Select a language by
40
and
SELECT buttons and press the OK button.
This automatically sets the power from standby to ON when the indicated
time period has elapsed. The settable time is 00:00~11:59. Input the
required time by
and
SELECT buttons on the remote control.
ENGLISH
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
Menu
Picture
Display
Registration condition
Picture Mode
1 setting is registered.
Contrast
For every input function and every
Picture Mode, 1 setting is registered.
Brightness
Menu
Function
Display
1 setting is registered.
Screen Wipe
(not registered)
Black Side Panel
1 setting is registered.
Color
Video Power Save
Shapness
Freeze Mode
Tint
Default Zoom
Color temperature
Setup
Contrast Mode
System
1 setting is registered.
Color System
—
Back Light
AV1
YNR
AV2
CNR
AV3
Film Mode
AV4
PAL Comb Filter
For every input function, 1 setting is
registered.
AV5
LTI
Video Input
CTI
—
AV1
Black Enhancement
1 setting is registered.
AV2
Auto Color
RGB1
Color Temp. Adjust
RGB2
For every Color Temperature, 1
setting is registered.
R Amplitude
1 setting is registered.
G Amplitude
Input Level
B Cut Off
WVGA Type
WXGA Mode
1 setting is registered.
Vertical Filter
Red
Frequency Mode
Yellow
Language
Green
Cyan
Blue
—
Red
Green
Color
Tint
For every Color Temperature, 1
setting is registered.
1 setting is registered.
Treble
For every Audio Mode, 1 setting is
registered.
Balance
1 setting is registered.
Dynamic Bass
For every Audio Mode, 1 setting is
registered.
Matrix Surround
1 setting is registered.
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals with which
all the elements are the same or similar will be handled as the
same signal.
For every input function and every
Picture Mode, 1 setting is registered.
Audio Mode
Bass
1 setting is registered.
Frequency Display
For every input function and every
Picture Mode, 1 setting is registered.
Color Decoding
For every signal Mode, 1 setting is
registered. (Only for RGB2)
Clock Phase
G Cut Off
Megenta
(not registered)
Horizontal Clock
R Cut Off
Color Management
Auto Adjust
Horizontal Position
Vertical Position
B Amplitude
Audio
Registration condition
Screen Saver
Perfect Volume
Headphone Volume
Headphone Select
41
OTHER FEATURES (continued)
Audio Switching
A2 / NICAM / Sound Multiplex (TV mode)
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
NICAM [II]
BILINGUAL / DUAL sound broadcast
When bilingual program is received, sound mode display appears in yellow as shown on right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or
(force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Yellow
Green
Yellow
[I]
NICAM signal received
[II]
Yellow
Yellow
NICAM [II]
NICAM [I]
Select I, II or
Green
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
When a stereo program is received, sound mode display will appear in red, and you can
press the CH I / II button to select between stereo and mono sound.
8
Each time the button is pressed,
or (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
NICAM
Select
or
Red
Green
(force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
When a monaural program is received, sound mode display will appear in green.
You can press the CH I / II button to select the sound mode between monaural and forced
mono (sound is same).
Each time the button is pressed,
or
(force mono) appear cyclically on the screen.
NOTE
• If sound signal is not strong enough for quality reception, press the CH I / II button until
appears on the screen to receive a clear
mono sound.
• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until
appears on the screen to receive a clear mono sound.
42
8
ENGLISH
OTHER FEATURES (continued)
Power Save Mode
When the RGB1, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
No
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
158W
3W or less
Returning to operating status
• Operate the personnal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote
control.
DVD Player/ STB Selection
• You can use this remote control to operate the selected maker of DVD Player and STB by pressing the following buttons on the remote
control simultaneously.
<“DVD” Selection>
Makers of DVD Player
Set Maker
Set Type
Makers of DVD Player
Set Maker
HITACHI
RCA
FUNAI
Mitsubishi
Pioneer
ONKYO
RED
Panasonic
ZENITH
GREEN
TOSHIBA
THOMSON
YELLOW
Philips
SHINCO
BLUE
JVC
SKYWORTH
SAMSUNG
BUBUKO
Sony
DENON
Set Type
Sharp
2-4-12
<“SAT” Selection>
Makers of STB Player
Set Maker
Set Type
HITACHI
TOSHIBA
DGTEC
Panasonic
43
OTHER FEATURES (continued)
DVD Player/STB Selection (continued)
Set up hint
Example) HITACHI DVD
To operate HITACHI DVD player, press and hold the
button,
followed by the
button.
1. Set up the maker
button to indicate the DVD LED on the remote control.
Press
While the DVD LED is flashing, press
2. Set up the maker type
Release the
button while keeping
and
.
button depressed.
Then, press the
button.
3. Confirm the setting
After setting the maker and type, press the POWER button on the remote control.
If the DVD does not switch on, repeat step 1 and 2 using other maker types as listed in the chart on 43 .
NOTE
• Not all models of the listed makers can be operated using this remote control.
Signal Check (RGB mode)
Changes in the signal status are displayed on the screen as they arise.
Status
Display
RGB
Action
When Frequency Display is set to ON,
the input signal is switched or when
the RECALL button is pressed.
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
When the sync signal is no longer
detected.
• A guide displays No Sync. Signal,
and Power Save (for approx. 5 sec.)
• When the condition continues where
the sync signal cannot be detected,
indicator lamp of power source
changes in orange and the mode
switches to power save mode.
Recheck the personal computer
power switch status and the
connection status.
A guide displays Invalid Scan Freq.
Recheck the input signal
specifications. 50 ~
When the input signal does not match
the monitor specifications or is in an
unstable status.
! No Sync. Signal
52
! Invalid Scan. Freq.
44
ENGLISH
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating lamp off.
• Check the way the power cable is connected.
• Press the power switch.
See page
18
19
• The message “No Sync. Signal” or “Power
Save” is displayed.
! No Sync. Signal
• No picture with the power indicating lamp
lights in orange.
• The message “Invalid Scan Freq.” is
displayed.
! Invalid Scan Freq.
No sync signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging
equipment, etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
• Check the way the signal cable is connected.
15
15
50
51
52
• The power indicating lamp is normally lit but
no picture.
• Check the contrast and brightness settings (adjust them for
higher contrast and brightness).
• Check the way the signal cable is connected.
15
36
38
• The display image appears flowing slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot
clock frequency first, the dot clock phase next.)
(RGB input)
32
47
• Text displayed across the screen appears
blurred.
• A fine pattern flickers when displayed on the
screen.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
32
47
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control
in opposite direction.
• Check to see if the batteries in the remote control are OK.
• The display image does not appear in the
normal position.
• Check to see if the displayed input signal match the monitor
specification by pressing
button.
• Turn off the screen saver.
9
15
34
50
51
52
• The display has lack of picture around the
screen.
(PC input mode only)
• Turn off the screen saver.
• The temperature of the display panel surface is high.
• The LCD monitor is lighting the fluorescent lamps inside of
the panel.
In some cases, this may cause the temperature of the panel
surface to increase. Please note that this is not a malfunction.
34
—
45
TROUBLESHOOTING (continued)
Symptoms That Seemingly Appear to be Failures (continued)
Symptom
• There are locations on the screen that are different from the
periphery (*).
* Points that do not light, points with brightness different
from that of the periphery, points with color different from
that of the periphery, etc.
Point to check
• High-precision technology is used to manufacture the LCD
panel. However in some cases, there are minor defects in
some parts of the screen. Please note that this is not a
malfunction.
See page
—
• Coarse horizontal stripes appear in FULL display.
• Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
32
• Flickering in the form of horizontal lines oscillating up and down.
(PC INPUT MODE only)
• If the direct frequency from the computer is below 85Hz, try
a higher frequency (upper limit 85Hz). There may be a slight
attenuation of the current image.
• Try turning the Vertical Filter On. For this case however, the
vertical resolution will drop.
33
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor
may heat up. This is not a malfunction.
—
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images
with a vertical resolution greater than 768 lines are
displayed; however, this is not a malfunction.
—
• The screen becomes dark and the images cannnot be seen
during VTR special playback (fast forward, rewind)
• This sometimes occurs when a component output VTR such
as the 480i is connected.
This is not a malfunction; therefore, please take note that
this may occur. When it does occur, change to composite
output,or S.video output.
—
• During multi picture mode, sub pictures are not displayed.
• Sub pictures image might not be able to be displayed,
depending on the combination.
(Reter to the table of “2 pictures mode” and “4 pictures
mode”)
26
• The screen display sizes are not switched.
• The screen display size is fixed at “Full” as receiving
1080i/60Hz, 1080i/50Hz, and 720p/60Hz.
—
• Images from AV6 (HDMI) are not displayed.
• Check the cable and output format of connecting device.
(Reter to “Connecting to an Audio Visual Device”, and
"Recommended Signal List".)
13
46
50
ENGLISH
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments
suggested below. (only for RGB2)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1).
Figure 1
Vertical Streaks
Before adjustment.
Some characters are blurred.
After adjustment.
All characters appear
crisp now.
Example
After adjustment.
All characters are
blurred.
1)
2)
3)
4)
Adjustment
procedure
Press the MENU button. The Main Menu will be displayed.
Press the
SELECT button and select Setup.
Press the OK button. The Setup Menu will be displayed.
Press the
SELECT button and select Auto Adjust.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the
SELECT button and select Setup.
7) Press the OK button. The Setup Menu will be displayed.
8) Press the
SELECT button and select Horizontal Clock.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.)
9) Press the or ADJUST buttons and search for clear characters over the entire screen.
10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (Figure 2).
A fine pattern flickers when displayed on the screen (Figure 3).
Figure 2
Before adjustment
Figure 3
Before adjustment
Example
After adjustment
1)
2)
3)
4)
Adjustment
procedure
After adjustment
Press the MENU button. The Main Menu will be displayed.
Press the
SELECT button and select Setup.
Press the OK button. The Setup Menu will be displayed.
Press the
SELECT button and select Auto Adjust.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the
SELECT button and select Setup.
7) Press the OK button. The Setup Menu will be displayed.
8) Press the
SELECT button and select Clock Phase.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
9) Press or ADJUST buttons to make the text appear
clean across the screen.
9) Press or ADJUST buttons to make the text appear
without flickering.
47
PRODUCT SPECIFICATIONS
Product specifications and designs are subject to change without notice.
Display
dimensions
Resolution
Net dimensions
Net weight
Ambient
Temperature
Relative humidity
conditions
Power supply
Panel
Power consumption/at standby
Audio output
(RGB input)
Input terminals
Input signals
Sync signals
Recommended signal
Approx.32 inches (698 (H) x 392 (V) mm, diagonal 800 mm)
1366 (H) x 768 (V) pixels
1015(W) x 618 (H) x 340 (D) mm
25.0 kg
Operating: 5°C to 35°C, Storage: -15°C to 60°C
Operating: 20% to 80%, Storage: 20% to 90%(non-condensing)
AC100-240V, 50/60Hz
158W/<1W
/<2W ( only when DVI used )
speaker 12W+12W (6Ω)
RGB1 DVI input terminal (DVI-D)
RGB1 audio input terminal (3.5mm Stereo Mini Jack)
RGB2 analog RGB input terminal (D-sub 15-pin)
RGB2 audio input terminal (3.5mm Stereo Mini Jack)
0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
H/V separate, TTL level [2KΩ]
H/V composite, TTL level [2KΩ]
Sync on green, 0.3 Vp-p [75Ω]
44 modes 51
52
(Video input)
Input terminals
Input signals
AV1: composite video input terminal (RCA)
AV1: Y/PB/PR video input terminal (RCA)
AV1: L/R audio input terminal (RCA)
AV2: composite video input terminal (RCA)
AV2: Y/PB/PR video input terminal (RCA)
AV2: L/R audio input terminal (RCA)
AV3: composite video input terminal (RCA)
AV3: S video input terminal
AV3: L/R audio input terminal (RCA)
AV4: composite video / L/R audio input terminal (RCA)
AV5 = AV3
AV6: HDMI input terminal
AV1: PAL, SECAM, NTSC3.58, NTSC4.43
AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV2: PAL, SECAM, NTSC3.58, NTSC4.43
AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
AV3: PAL, SECAM, NTSC4.43, NTSC3.58
AV4: PAL, SECAM, NTSC4.43, NTSC3.58
AV5 = AV3
AV6: HDMI input signal 50 .
Output signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor-output terminal (RCA)
OUTPUT (HEADPHONE): L/R audio monitor-output terminal (Mini-pin)
Recommended signal
23 modes 50
51
(RF input)
Input terminals
ANT: 75Ω Unbalanced
RF Video System
PAL B, G, H / I / D, K
SECAM B, G / D, K / K1
NTSC-M
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
48
ENGLISH
PRODUCT SPECIFICATIONS (continued)
Signal Input
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
R(PR/CR)
1
G or sync on green (Y)
2
B (PB/CB)
3
No connection
4
No connection
5
R.GND (PR/CR. GND)
6
G.GND (Y. GND)
7
B.GND (PB/CB. GND)
8
No connection
9
GND
10
No connection
11
[SDA]
12
H. sync or H/V composite sync
13
V.sync. [V.CLK]
14
[SCL]
15
(
• When different kinds of input signals are simultaneously input
to the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
) : With component input
Sync signal type
Priority
H/V separate sync.
1
H/V composite sync.
2
sync.on Green *
3
* Even in the case of the recommended signals shown on the
following page, there may be instances when correct display
is not possible. In this case, use H/V separate sync, H/V
composite sync.
S-input connector pin specifications
Pin
Input signal
Y
1
Y-GND
2
C
3
C-GND
4
GND
Frame
HDMI connector pin specifications
Pin
Input signal
Pin
TMDS Data2+
1
11
TMDS Data2 Shield
2
12
TMDS Data23
13
TMDS Data 1+
4
14
TMDS Data1 Shield
5
15
TMDS Data16
16
TMDS Data0+
7
17
TMDS Data0 Shield
8
18
TMDS Data09
19
TMDS Clock+
10
Input signal
TMDS Clock Shield
TMDS ClockCEC
Reserved(N.C. on device)
SCL
SDA
DDC/CED Ground
+5V Power
Hot Plug Detect
DVI terminal (DVI-D)
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Input signal
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
DDC Clock
DDC Data
No Connect
T.M.D.S. Data1T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
T.M.D.S. Data3-
Pin
14
15
16
17
18
19
20
21
22
23
24
Frame
Input signal
+5V Power
Ground (for+5V)
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. ClockGND
T.M.D.S. Data3-
49
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
Applicable video signals for input terminal (TV mode)
Terminal
RCA/S-video
S-video
Component
HDMI
DVI
PC
D-sub
STB
RGB
Remarks
Signal Name
CVBS
Component
AV1
O
O
Refer to Setup Menu 31
AV2
O
O
Refer to Setup Menu 31
AV3
O
AV4
O
AV5
O
O
Refer to Setup Menu 31
Refer to Setup Menu 31
O
Refer to Setup Menu 31
AV6
O
RGB1
O
O
Refer to Setup Menu 33
RGB2
O
O
Refer to Setup Menu 33
(O:Available)
With composite input(AV1~AV5 input) and S-video input (AV3, AV5 input).
Signal mode
No.
Horizontal
frequency (kHz)
Signal Name
Resolution
Vertical frequency
(Hz)
1
NTSC4.43
NTSC3.58
525
59.94
15.73
2
PAL
SECAM
625
50.00
15.63
Dot clock
frequency (MHz)
Remarks
With component input (AV1, AV2 and RGB2-component input).
Signal mode
Signal Name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
576i
576
50.00
15.63
2
480i
480
59.94
15.73
3
576p
576
50.00
31.26
No.
1
Dot clock
frequency (MHz)
Remarks
4
480p
480
59.94
31.47
5
1080i/50
1080
50.00
28.13
6
1080i/60
1080
60.00
33.75
7
720p/60
720
60.00
45.00
Dot clock
frequency (MHz)
Remarks
With HDMI input (AV6 input).
Signal mode
Signal Name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
1
VGA
640 x 480
59.94
31.47
25.18
EIA-861B
2
576i
720(1440) x 576
50.00
15.63
27.00
EIA-861B
3
480i
720(1440) x 480
59.94
15.73
27.00
EIA-861B
4
576p
720 x 576
50.00
31.25
27.00
EIA-861B
No.
5
480p
720 x 480
59.94
31.47
27.00
EIA-861B
6
1080i/50
1920 x 1080
50.00
28.13
74.25
EIA-861B
7
1080i/60
1920 x 1080
60.00
33.75
74.25
EIA-861B
8
720p/60
1280 x 720
60.00
45.00
74.25
EIA-861B
50
ENGLISH
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List (continued)
With Digital signal input.
Signal mode
No.
1
2
3
Signal Name
VGA
640 X 400
70.08
31.47
25.18
O
640 X 480
59.94
31.47
25.18
O
864 X 480
59.94
31.47
34.24
O
4
640 X 480
72.81
37.86
31.50
O
5
640 X 480
75.00
37.50
31.50
O
6
640 X 480
85.01
43.27
36.00
O
7
800 X 600
56.25
35.16
36.00
O
8
800 X 600
60.32
37.88
40.00
O
800 X 600
72.19
48.08
50.00
O
800 X 600
75.00
46.88
49.50
O
9
W-VGA
Resolution
Horizontal Dot clock Setup Menu Condition
Vertical frequency frequency frequency
DVI-PC
DVI-STB
(kHz)
(MHz)
(Hz)
VESA
10
11
800 X 600
85.06
53.67
56.25
O
12
1024 X 768
60.00
48.36
65.00
O
13
1024 X 768
70.07
56.48
75.00
O
14
1024 X 768
75.03
60.02
78.75
O
Remarks
O
WVGA type: On
15
480p
720 X 480
59.94
31.47
27.00
O
EIA-861B
16
576p
720 X 576
50.00
31.25
27.00
O
EIA-861B
17
720p/60
1280 X 720
60.00
45.00
74.25
O
EIA-861B
18
1080i/60
1920 X 1080
60.00
33.75
74.25
O
EIA-861B
19
1080i/50
1920 X 1080
50.00
28.13
74.25
O
EIA-861B
(O:Acceptable)
51
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List (continued)
With Analog signal input (RGB2 input)
Signal mode
No.
1
2
Signal Name
VGA
Resolution
Vertical frequency
(Hz)
640 X 400
70.08
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
31.47
25.18
640 X 480
59.94
31.47
25.18
864 X 480
59.94
31.47
34.24
4
640 X 480
72.81
37.86
31.50
5
640 X 480
75.00
37.50
31.50
6
640 X 480
85.01
43.27
36.00
7
800 X 600
56.25
35.16
36.00
8
800 X 600
60.32
37.88
40.00
9
800 X 600
72.19
48.08
50.00
10
800 X 600
75.00
46.88
49.50
11
800 X 600
85.06
53.67
56.25
1024 X 768
60.00
48.36
65.00
1024 X 768
70.07
56.48
75.00
14
1024 X 768
75.03
60.02
78.75
15
1024 X 768
85.00
68.68
94.50
3
W-VGA
12
13
VESA
16
1152 X 864
75.00
67.50
108.00
17
1280 X 1024
60.02
63.98
108.00
18
1280 X 1024
75.03
79.98
135.00
19
1280 X 1024
85.02
91.15
157.50
20
1600 X 1200
60.00
75.00
162.00
21
1600 X 1200
75.00
93.75
202.50
22
1600 X 1200
85.00
106.25
229.50
23
640 X 480
66.67
35.00
30.24
24
25
Macintosh
832 X 624
74.55
49.72
57.28
1024 X 768
74.93
60.24
80.00
26
1152 X 870
75.06
68.68
100.00
27
1280 X 768
59.833
47.986
81.00
28
29
30
W-XGA
W-XGA
Remarks
WVGA type: On
1280 X 768
69.997
56.137
94.760
1280 X 768
59.876
47.776
79.50
WXGA Mode:1280X768
1366 X 768
60.015
47.712
85.50
WXGA Mode:1366X768
• The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position, Vertical Position.
Horizontal Clock and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 768 lines of vertical resolution at Full display (compressed display) can result in the interpolation of
stripes.
52
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement