Hitachi CMP4221 User's Manual

Hitachi CMP4221 User's Manual
ENGLISH
CMP4221
USER'S MANUAL
Thank you very much for purchasing the HITACHI Plasma Display Monitor.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to
operate the monitor properly. Keep this manual in a safe place. You will
find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake in
installation or mounting, misuse, modification or a natural disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
1
IMPORTANT SAFETY INSTRUCTIONS
!
SAFETY POINTS THAT YOU SHOULD KNOW ABOUT YOUR HITACHI PLASMA MONITOR
Our reputation has been built on the quality, performance, and ease of service of HITACHI Plasma monitor.
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be
of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI Plasma monitor.
Follow all warnings and instructions marked on this monitor.
The lightning flash with arrowhead symbol, within an
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
z TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.
zTHE MONITOR SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE MONITOR.
z There are no user serviceable parts inside the monitor.
z Model and serial numbers are indicated on the rear side
NOTE:
CAUTION:
of the monitor.
Adjust only those controls that are covered in these instructions, as improper changes or modifications not
expressly approved by HITACHI could void the user's authority to operate the monitor.
MODIFICATIONS: The FCC requires that the user be notified that any changes or modifications made to this device, that are not
expressly approved by HITACHI America, Ltd. Home Electronics Division may void the user's authority to
operate the equipment.
!
POWER SOURCE
THIS MONITOR IS DESIGNED TO OPERATE ON 100-240 VOLT 50/60Hz, AC CURRENT. INSERT THE POWER CORD INTO Aʳ120
VOLT 60Hz OR 240 VOLT 50Hz OUTLET.ʳ
TO PREVENT ELECTRIC SHOCK, DO NOT USE THE MONITOR’S (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE. NEVER CONNECT THE MONITOR TO DIRECT CURRENT OR ANYTHING OTHER THAN THE SPECIFIED
VOLTAGE.
CAUTION:
!
2
Never remove the back cover of the monitor as this can expose you to very high voltages and other
hazards. If the monitor does not operate properly, unplug the monitor and call your authorized dealer or
service center.
ENGLISH
!
IMPORTANT SAFETY INSTRUCTIONS
!
Read before operating the appliance
Follow all warnings and instructions marked on this monitor.
1. Read these instructions.
2. Keep these instructions.
provided on the bottom panel of the unit.
18. This appliance is designed to comply with the recommended safety
Do not pull the cabinet with excessive force. Doing so can cause the
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and at the point
where they exit from the apparatus.
11. Only use the attachments/accessories specified by the
manufacturer.
product to overturn, resulting in damage to the product and/or
personal injury.
19. Follow instructions for wall, shelf, or ceiling mounting as
recommended by the manufacturer.
20. An outdoor antenna should not be located in the vicinity of overhead
power lines or other electrical circuits.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long
periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as when a
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15.To Reduce the Risk of Fire or Electric Shock, Do not Expose This Appliance
To Rain or Moisture.
16.Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, shall not be placed on the apparatus.
Do not place any objects on top of the monitor. They may fall or cause a child to climb up to retrieve the objects.
Disposal of this product may require specific instructions pertaining to your resident state. For disposal or recycling
information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
!
CAUTION:
!
PREVENTION OF SCREEN BURN IN
Continuous on-screen displays such as video games, stock market quotations, computer generated
graphics and other fixed (non-moving) patterns can cause permanent damage to the monitor. Such
“SCREEN BURN IN” constitute misuse and are NOT COVERED by your HITACHI Factory Warranty.
PUBLIC VIEWING OF COPYRIGHTED MATERIAL
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require
prior authorization from the broadcaster or owner of the video program material.
3
ENGLISH
standards for tilt and stability.
3. Heed all warnings.
12
17. The Shock Hazard Marking and Associated Graphical Symbol is
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 4 to 7. Mis-use may cause damage to your plasma
monitor, which could shorten its lifespan, or cause injury to yourself.
Should you encounter any difficulty in the set-up or operation of your
monitor, firstly refer to the Troubleshooting guide at the rear of this manual.
In the unlikely event of a problem occurring with your plasma monitor,
switch off at the mains sockets, pull out the plugs, and contact your dealer
immediately.
CAUTION
Under no circumstances remove the rear cover of your plasma monitor.
Never guess or take any chances with electrical equipment of any kind - it
is better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse engineer or
reverse compile the software included therein, save to the extent permitted
by law.
Plasma monitor
After the plasma monitor has been on for any length of time, you will notice
that the screen becomes warm. Please note that this is normal. Sometimes
the screen might have some tiny bright or dark spots. Please note that this
is normal.
CAUTION
To prevent scratches or damages to the plasma screen, do not knock or
rub the surface with sharp or hard objects. Clean the screen with a soft
cloth moistened with warm water and dry with a soft cloth. A mild soap may
be used if the screen is extremely dirty. Do not use harsh or abrasive
cleaners!
CAUTION
Use a soft cloth to clean the cabinet and control panel of the monitor. When
excessively soiled dilute a neutral detergent in water, wet and wring out the
soft cloth and afterward wipe with a dry soft cloth. Never use acid/alkaline
detergent, alcoholic detergent, abrasive cleaner, powder soap, OA
cleaner, car wax, glass cleaner, etc. especially because they would cause
discoloration, scratches or cracks.
4
CARACT ÉRISTIQUES
FEATURE
Large-screen, high-definition plasma
display panel
The 42-inch color plasma display panel, with a resolution of 1024 (H) x
1024 (V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9)
and low-profile flat display. Free from electromagnetic interferences from
geomagnetic sources and ambient power lines, the panel produces
high-quality display images free from color misconvergence and display
distortion.
High Performance Digital Processor
A wide range of input signals can be handled, including composite,
component, and HDMI. High Definition Digital processor creates the
fine-textured image with dynamic contrast. In addition, a wide range of
personal computer signals can be handled, from 640 x 400, 640 x 480
VGA to 1600 x 1200 UXGA. (RGB Analog input)
Easy-to-use remote control and on screen
display system
The remote control included eases the work of setting display controls.
Further, the on-screen display system, displays the status of signal
reception and display control settings in an easy-to-view fashion.
Connecting to an Audio Visual Device
z
z
Two composite and S-Video terminal, two component terminal, a PC
RGB terminal and a HDMI terminal have been added.
A wide range of device can besides personal computers.
Options
Ask your local retail dealer for further details.
1. Desktop stand:
x CMPAD24
2. Plasma monitor speaker:
x CMPAS24
ENGLISH
Important
IMPORTANT SAFETY INSTRUCTIONS…………....….2
FEATURE…………………………………………….………….4
SAFETY INSTRUCTIONS……………………………....….6
COMPONENT NAMES………….………………………….10
Main Unit…………………………………………………………10
Remote Control…………………………………………….…..11
Loading the Batteries……………………………………………11
Handing the Remote Control…………………………………..11
INSTALLATION INSTRUCTIONS…………………...….12
Installation the Desktop stand(option)……….………………..12
Anti-tumble measures…………………………….……..…..…..12
Mounting the Speaker Unit(option)…………..............…..…..12
Connecting to Video Imaging Device……………..….……….13
Connecting to a PC or a HDMI device…….………...………..14
Power Cord Connection………………….……………………..15
OPERATING INSTRUCTIONS………….………….…....16
Turning Power On and Off…………….………………………..16
Input Switching.......………………….………………………......17
Volume Adjustment.......………………….……………………..17
Audio Mute.......………………….…………………….……......17
Size Switching.......………………….………………………..…..18
Input Signal Screen Desplay......……….……………………... 18
Automatic Adjustment of Screen Pocition and the clock…... 18
Using the Menu Screen………….………………………..…..19
Picture Menu...........………………….……………………...........21
Image Menu……....………….………………. . . . …… … ..... . 22
Audio Menu……....………………………….………….............24
Function Menu…....…….……..….…………………...............25
Setup1 Menu…....…………..…….………….………………....27
Setup2 Menu……..……..……….………….……………...….28
OTHER FEATURE……………….………………………….…….29
Automatic Store………...…………………………………….………29
Signal Check (RGB Input)………………………………….………30
IMAGE RETENTION OF PLASMA DISPLAY…………..…31
NOTES………………………………..……….………………......31
TROUBLESHOOTING………….………….……………………32
Symptoms That Seemingly Appear to be Failures…………..…….32
Actions to Corrections Abnormal Displays………………………..34
PROUDCT SPECIFICATIONS………..……………………...35
Signal Input……………………………………………………….... 36
Recommended Signal List………………………………………....37
Notes about this manual
z
z
z
z
z
The information in this manual is subject to change without notice.
While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any comments,
views or questions about our product.
Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the product. We are
not held liable for damages caused by improper handling of the product.
Reproduction of this manual in whole or in part without our prior written permission is prohibited.
The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
5
ENGLISH
CONTENTS
SAFETY INSTRUCTIONS
This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if
you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
WARNING
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect
handling.
CAUTION
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to
incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or adjacent to the symbol (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or adjacent to the symbol. (The symbol to the
left indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration
of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then
disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never
attempt to make repairs yourself because this could be dangerous.
Disconnect the
plug from the
power outlet.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are
present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power
outlet and contact your dealer.
x Do not place the monitor in a bathroom.
x Do not expose the monitor to rain or moisture.
x Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
x Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
x Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the
glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact
your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
x Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and
shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
x Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
x Do not place anything around ventilation openings of the monitor.
x Never block ventilation openings.
x Do not put the plasma screen side up.
x Do not cover the monitor with a tablecloth, etc.
x Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the
monitor and the safety standard.
x The enclosed power cord must be used depending on the power outlet to be used.
6
Do not
Disassemble.
ENGLISH
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the users and to prevent
property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
x Do not touch the power cord with a wet hand.
x Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power
plug.
x Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
x Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an
appropriate extension lead or consult your dealer.
ENGLISH
x Should you require replacing the fuse in the molded plug with a new fuse, and then please replace with new one of the same value, type
and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power
cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or
Surely connect
the ground wire.
tension to the power cord and cables. If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
x Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this
could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
x Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the
plug or connector.
x Do not place the cord near the heater.
x Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
x Do not touch the power plug when lightening is close to you.
x Avoid coiling the power cord and bending it sharply.
x Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit
from the apparatus.
x Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
x Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
x Do not allow the battery to be exposed to fire or water.
x Avoid fire or high-temperature environment.
x Do not hold the battery with metallic tweezers.
x Keep the battery in a dark, cool and dry place.
x Do not short circuit the battery.
x Do not recharge, disassemble or solder the battery.
x Do not physically impact the battery.
x Use only the battery specified in the manual of this monitor.
x Make sure the plus and minus terminals are correctly aligned when loading the battery.
x If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse
well with water.
x Obey the local laws on disposing the battery.
7
SAFETY INSTRUCTIONS(continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
x Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
x You are advised to move the monitor with two persons.
x Avoid any impact or shock to the monitor; particularly take care of glass screen.
ENGLISH
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
x Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
x Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
x Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
x For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
x Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Disconnect the
plug from the
power outlet.
Never remove the back cover of the monitor as this can expose you to very high voltages and other
hazards
x If the monitor does not operate properly, unplug the monitor and call your authorized dealer or service center.
Prevention of screen burn in
x Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can
cause permanent damage to the monitor. Such “SCREEN BURN IN” constitutes misuse and is NOT COVERED by our Factory Warranty.
These servicing instructions are for use by qualified service personnel only
x To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Do not place any objects on top of the monitor
x They may fall or cause a child to climb up to retrieve the objects.
PRECAUTIONS
Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
x Hot places such as near heater, place exposed to the direct rays of the sun.
x A place where the temperature is widely changing.
x Places with soot, dust or high humidity.
x Poor air ventilation place.
x Place near fire.
x A wet place such as bathroom, or shower room.
x Place where you can trip over it.
x Always vibrating or strongly vibrating places.
x Distorted or unstable places.
How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
Note on image retention
The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness
of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Please refer to the user manual for this model for instruction on how to use these features.
x Ensure screen saver mode is activated.
x Always display the image in a mode that fills the screen.
x Avoid using split screen mode for long periods of time.
x Do not allow the “On Screen Display” to stay on for long periods of time.
x Do not display still images, such as menus from game consoles, T/Text, PCs or logos, on the panel for long periods of time.
x We recommend that the “Contrast” and “Brightness” level is reduced as much possible.
How to clean the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth
moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.
8
How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft
cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they
would cause discoloration, scratches or cracks.
Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
x Keep the monitor away from Radio.
x Adjust Radio antennas in order for the monitor not to receive interference.
x The antenna cable of Radio should be kept away from the monitor.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
Precautions for the cable connection
ENGLISH
x Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are properly made
and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing connections.
x Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
x Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc.
x Use a plug with ground terminal and make sure that it connects to the ground.
Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
x A physical impact could cause damage or malfunction of the remote control.
x Take care not to drop the remote control.
x Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
x Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
x Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand or legs with
the fixings provided according to the instructions.
x Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
x This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of
the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
x Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
x Only use the attachments/accessories specified by the manufacturer.
x Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
x Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by
mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.
x Disposal of this product may require specific instructions pertaining to your resident region.
x Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
9
COMPONENT NAMES
NOMS D ES COM POSANT S
Main Unit
Front
ENGLISH
Panel
Control Panel
x Adjustment buttons are located
on the bottom.
x The back cover is provided with
indications to distinguish the
adjustment buttons.
Remote-control
sensor 11
MENU button 19
Indicating lamp 16
SOURCE button
17
• The main power switch is located at the back, on the lower
surface.
Main power switch (See page 16 )
OK button
VOLUME UP/DOWN buttons
(W XADJUST buttons) 17
PROGRAM UP/DOWN
buttons
(S TSELECT button.) 19
SUB-POWER button (See page 16 )
x (
) indicates the function while the MENU is displayed on the screen.
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Rear
Handgrips
Handgrips
10
External
Speaker
Terminals
External
Speaker
Terminals
13
13
Remote Control
l
POWER OFF button
16
POWER ON/OFF
16
HDMI button
17
RGB button
17
17
AV1 button
AV2 button
17
17
VOLUME UP/DOWN buttons
17
MUTE button
AV3 button
17
17
AV4 button
OK button
19
19
SELECT/OK buttons
MENU button
19
19
RETURN button
AUTO button
18
18
RECALL button
PIP button
25
17
SIZE button
Loading Batteries
1. Open the battery cover.
Slide back and remove the battery
cover in the direction of the arrow.
b tt
ENGLISH
POWER ON button
16
Handing the Remote Control
Handling the Remote Control
Use the remote control within about 5m from the front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
Load two Size AAA batteries included observing the Polarities.
With in 30
degrees
About 3m
With in 30
degrees
About 3m
About 5m
3. Close the battery cover.
Replace the battery cover in the direction of the arrow and snap it back
into place.
CAUTION
z
z
Do not use new and old batteries together. The batteries could explode or
leak, resulting in fires, physical injury, or stains.
When loading batteries, observe their correct polarities as marked on the
product. If loaded in the wrong direction, the batteries could explode or
leak, resulting in fires, physical injury, or stains.
ATTENTION
z
z
z
z
z
Do not drop or impact the remote control..
Do not splash the remote control with water or put it on a wet object.
Before leaving the remote control out of use for an extended period of
time, remove the batteries from it.
If the remote control begins to lack responsiveness, replace the
batteries.
Strong light, such as direct sunlight, shining on the photoreceptor of
the remote control can cause operational failure.Position this unit to
avoid direct contact with such light.
11
INSTALLATION INSTRUCTIONS
Installation the Desktop stand
(option)
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or dropping and
result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage caused
by use of other mount units or improper installation.
CAUTION
x Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this by our self. Ask your dealer
to provide the name of a qualified installer.
x In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches: For a desktop set- up) or more
between the sides and other objects such as walls, etc., so that the ventilation holes are not blocked. (*)
10cm (4 inches) or more*
Clamp
Cord
or
chain
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
Hook
Chain
cord or chain
Wall or Pillar
Clamp
Securing desktop
1) Using wood screws (two) fasten the set to the clamping screw holes on the rear of the stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood
Two places
Mounting the Speaker Unit
(option)
Refer to the instruction manual concerning mounting of the optional speaker unit.
12
ENGLISH
• If you have purchased the model without the stand attached:
When installing the monitor, use the optional Desktop stand.
The Desktop stand has been used for the illustrations in this manual.
INSTALLATION INSTRUCTIONS (continued)
Read SAFETY INSTRUCTIONS ( 2 to 9 ) carefully to ensure maximum safety before proceeding to
these steps:
Choose an appropriate site and install the product on a level table where the stand is secure.
x
Install the monitor to have ready access to a power socket available.
Make sure that the power switch of this device is turned off.
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
x See "Product Specifications" concerning the specifications of this device.
35 ~ 37
(2) Make sure that the power switch of the monitor is turned off.
(3) Make sure that the power switch of the imaging device is turned off.
(4) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this device and the
signal output terminal of the imaging device.
* Cable shown are not supplied with the monitor and are available locally
where ever consumer electronic product are sold.
CAMCORDER
Monitor rear panel
Speaker(R)
Speaker(L)
DVD PLAYER
SPEAKER TERMINAL
(6ȍ) 10W
SPEAKER TERMINAL
(6ȍ) 10W
Power Code
Basic Connection
Set-TopBox
Better
Connection
VCR
[An example of connecting video components]
z
z
If the AV OUT terminal is connected to a 2nd monitor, it is possible to view the same image as on the main source. The composite video signal
from AV1, AV2 input will be displayed on both screens at the same time.
If video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer vedio quality.
Applicable signals for each input terminal
Applicable Signal
RCA
(See PRODUCT SPECIFICATIONS for details, 35 )
RCA
D-sub
Component
RGB
S-video
Terminal
Composite
AV1
Ϥ
Ϥ
AV2
Ϥ
Ϥ
HDMI
AV3
Ϥ
AV4
Ϥ
RGB
HDMI
Ϥ
Ϥ
(O: Available)
13
ENGLISH
Connecting to Video Imaging Device
Connecting to a PC or a HDMI device
Con
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
x See "Product Specifications" concerning the specifications of this device. 35 ~ 37
Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
x Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with the
personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal
computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker(R)
Speaker (L)
SPEAKER TERMINAL
(6ȍ )10W
Power Cable
Connector
SPEAKER TERMINAL
(6ȍ )10W
Power
Cord
3.5mm
Stereo
mini jack
(D-Sub)
(HDMI)
3.5mm
Stereo
mini jack
ϡ1
To Audio
Output
To Audio
Output
PC
DVD Player
ϡ1 In case of using analog audio, when connecting with DVI-HDMI transformation connector, use HDMI audio terminal for input.
x HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
x HDMI (High-Definition Multimedia Interface) is a digital interface based on DVI (Digital Visual Interface), which is an added function for audio visual
equipment.ʳ
Ёʳ ˜̇ʳ˷̂˸̆ʳ́̂̇ʳ˻˴̉˸ʳ˷˸˺̅˴˷˴̇˼̂́ʳ˵̌ʳ̇̅˴́̆̀˼̆̆˼̂́ʳ̆˼́˶˸ʳ˼̇ʳ˼̆ʳ˷˼˺˼̇˴˿ˁʳ
Ёʳ ˪˼̇˻ʳ̂́˿̌ʳ̂́˸ʳ˶˴˵˿˸ʿʳ˼̇ʳ˼̆ʳ̃̂̆̆˼˵˿˸ʳ̇̂ʳ̇̅˴́̆̀˼̇ʳ˵̂̇˻ʳ̃˼˶̇̈̅˸ʳ̆˼˺́˴˿̆ʳ˴́˷ʳ˴̈˷˼̂ʳ̆˼˺́˴˿̆ˁ
14
ENGLISH
(2) Make sure that the power switch of the personal computer or the DVD player is turned off.
(3) Connect the signal input terminal (RGB) or HDMI on the rear panel of this device.
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
ENGLISH
Connect the power cord, after completing all other connections.
c Connect the power cord to this device.
d Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
x Use only the power cord provided.
x Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
x Do not touch the power cord with a wet hand.
x Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
x Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
x Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an appropriate
extension lead or consult your dealer.
x Should you require replacing the fuse in the molded plug with a new fuse, and then please replace with new one of the same value, type and approval
as the original. Ensure the fuse cover is returned to its original position.
15
OPERATING INSTRUCTIONS
Indicating lamp
To turn the monitor power ON, press the main power switch on the
monitor main unit to ON, and then press the SUB POWER button or
the ON/OFF or ON button on the remote control.
To turn the monitor power OFF, press the SUB POWER button or
the ON/OFF or OFF button on the remote control, and then press the
main power switch on the monitor main unit to OFF.
z
During normal use, the main power switch is set in the ON position, and
the monitor can then be turned ON/OFF using the SUB POWER button or
the ON/OFF button on the remote control.
Indicating lamp
Indicating
lamp
Power status
Operating
OFF
OFF
When the main power switch is set
to OFF.
Lights red
ON
When the main power switch is set
to ON.
Lights green
ON
When the main power switch is ON,
and the ON button on the remote
control or the SUB POWER button
on the underside of the front of the
frame is ON.
Main power switch
Control Panel
x Avoid repeatedly turning the monitor on and off at short time intervals.
Failures might result from such operation.
x Turn off the main power switch before leaving the monitor out of use for
an extended period of time.
x If a power failure occurs while the main unit is running, it would be
powered on upon recovery from the failure. Turn off the unit main
power switch before leaving the main unit.
SUB-POWER button
POWER OFF
button
POWER ON
button
16
ATTENTION
POWER ON/OFF
button
ENGLISH
Turing Power On and Off
OPERATING INSTRUCTIONS (continued)
Volume Adjustment
ENGLISH
The volume can be adjusted by pressing the VOLSand
VOLT buttons of the remote control (or the Sand Tvolume
buttons of the monitor unit).
Volume setting value
VOLUME
buttons
UP/DOWN
SOURCE button
Adjustment status guide display
When a button is pressed, the volume adjustment status
guide will be displayed.
x The volume will increase when the VOL Sbutton is pressed while the
z
guide is being displayed.
x The volume will decrease when the VOL
Tbutton is pressed while the
guide is being displayed.
AV1,AV2,AV3,
AV4, RGB, HDMI
buttons
VOLUME
CONTROL
button
MUTE button
Select
buttons
Audio Mute
The audio volume can be temporarily muted by pressing the
MUTE button of the remote control.
RECALL button
AUTO button
SIZE button
z
When the MUTE button is pressed, the above icon will appear.
x The volume setting can be lowered by pressing the VOLT button while
the audio is muted.
x Muting can be cancelled by pressing the VOLS button or the MUTE
button while the audio is muted.
Size Switching
Size Switc hi ng
Each time the SIZE button of the remote control, the screen
display area will change in sequence and the status will be
displayed at the bottom of the screen.
Input Switching
Depending on the input signal format received, the picture format ratio
allows you to adjust the images through the following options.
(1)
4:3 Input signal of AV1, AV2, AV3, AV4
- Input can be switched by pressing the AV1, AV2, AV4, AV4, HDMI, or RGB
buttons of the remote control.
- AV1 S (AV2 S) Video input can be selected by two times pressing the AV1
(AV2) button of the remote control.
Full
(2)
HDMI
AV1 S
RGB
AV2
AV2 S
AV4
AV3
Full
(3)
Panoramic
RGB Input
Full
(4)
Cinema
16:9 Input signal 720p/60, 1080i/60 of AV3, AV4, HDMI
- Input can be switched in the sequence by pressing the SOURCE button of
the control panel.
AV1
Normal
Panoramic
Normal
HDMI Input
Full
Normal
x The size will fix as Full mode and not change when receiving 720p/60,
or 1080i/60
17
OPERATING INSTRUCTIONS (continued)
Size Switching (continued)
Size Switc hi ng
Display area selection diagram (RGB input)
Set the display size to
Play a 4:3 image faithfully in a 16:9
screen in the standard vertical size
and horizontally squeezed.
Input signal
Display screen
An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a
4:3 screen.
Full
(Squeeze)
Play a 4:3 image in a 16:9 screen
faithfully.
Normal
Play a 21:9 Cinema size image in the
4:3 image expanded vertically on the
16:9 screen.
Cinema
Play a 4:3 image faithfully in a 16:9
screen with the height and with of the
middle of the screen enlarged on
equal scales and with both sides
appearing somewhat enlarged.
Panoramic
Remarks
Blanking occurs on both sides.
(4:3 signal)
In some cases, some slight blanking may
remain at the top and bottom.
(Cinema)
An image with an aspect ratio of
Panoramic shrunk horizontally to 4:3 to
display in a 4:3 screen.
(4:3 Signal)
ATTENTION
Using a wide-screen monitor
x This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV program, the image
would appear different from the original. Take this into consideration when making screen mode choices.
x Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for commercial or pubic
viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
x When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear and/or appear
distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
x This mode allows 4:3 content to be viewed without picture distortion.
Automatic Adjustment of Screen Position and the Clock
Adjustment of the screen to a position suitable for the PC signal and the clock adjustment can be performed automatically
by pressing the AUTO button of the remote control.
CAUTION
Perform this adjustment for RGB and for each signal.
* Depending on the signal, satisfactory adjustment may not be possible in some cases. In such case, adjust by referring
to the Image Menu item.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control.
埛 The display will go out in approximately 2 seconds.
H: 48.4 kHz
V: 60.0 Hz
RGB
18
Input horizontal frequency of RGB
Input vertical frequency of RGB
Input mode
ENGLISH
When you want to
OPERATING INSTRUCTIONS (continued)
When the MENU button is pressed, the adjustment menu
screen will appear. Adjustment and setting are possible by
using the SELECT buttons; ADJUST buttons and the OK
button.
Refer to 20 _ 28 concerning the adjustment items and the settings.
PROGRAM UP/DOWN
buttons
Example: Selecting the Picture screen
1. Press the MENU button to display the Main Menu screen.
Picture Image Audio Function Setup 1
MENU button
045
092
Color
070
053
Tint
Sharpness
OK button
ADJUSTW X
buttons
Brightness
Contrast
Color Temperature
Black Enhancement
Gamma
Noise Reduction
SELECT buttons
RETURN button
013
Low
2.8
2.2
On
Off
2. Press OK button then Use theSand TSELECT buttons
to select the item.
Picture Image Audio Function Setup 1
Brightness
045
Contrast
092
Color
070
053
Tint
Sharpness
Color Temperature
Black Enhancement
Gamma
Noise Reduction
013
Low
2.8
2.2
On
Off
3. Use theWand Xto adjust (example: Brightness )
Picture Image Audio Function Setup 1
Brightness
040
Contrast
092
Color
070
053
Tint
Sharpness
Color Temperature
Black Enhancement
Gamma
Noise Reduction
013
Low
2.8
2.2
On
Off
x Press the RETURN button to return to the previous screen.
x If there is no operation for a period of 20 seconds, the
Adjustment Menu screen will disappear.
19
ENGLISH
Using the Menu Screen
(On-screen display system)
OPERATING INSTRUCTIONS (continued)
Picture Image Audio Function Setup 1
Brightness
045
Contrast
092
Color
Tint
070
Sharpness
Color Temperature
013
ENGLISH
053
Low
Black Enhancement
Gamma
Noise Reduction
2.8
2.2
On
Off
1. AV1~AV4, HDMI Input
Picture
Image
Audio
Function
Setup 1
Setup 2
Brightness
Picture Size
Volume
PIP H Position
Language
System Reset
Treble
PIP V Position
Off Timer
Freeze Mode
Contrast
Selected
characters
Color
Bass
PIP Layout
Screen Saver
Black Side Panel
Tint
Balance
Window Layout*1
Screen Wipe
Control Panel Lock
Sharpness
Mute
Main Picture*1
Standby White
Color Temperature
Audio Source*
1
Sub Picture*
1
Inverse
Black
Enhancement
Panel Life
Gamma
Noise Reduction
1
* Only available in the PIP mode.
2. RGB Input
Selected
characters
Picture
Image
Audio
Function
Setup 1
Setup 2
Brightness
Auto Adjustment
Volume
PIP H Position
Language
System Reset
Contrast
H Position
Treble
PIP V Position
Off Timer
Freeze Mode
Color Temperature
V Position
Bass
PIP Layout
Screen Saver
Black Side Panel
Screen Wipe
Control Panel Lock
Black
Enhancement
Horizontal Clock
Balance
Window Layout*
Gamma
Clock Phase
Mute
Main Picture*1
Noise Reduction
Mode Display
WVGA Type
Audio Source*
1
Sub Picture*
1
1
Standby White
Inverse
Panel Life
Vertical Filter
Frequency Mode
Picture Size
1
* Only available in the PIP mode.
20
PICTURE MENU
Picture
Brightness
Contrast
045
Color
Tint
Sharpness
Color Temperature
Black Enhancement
Gamma
Noise Reduction
070
ENGLISH
Picture Image Audio Function Setup 1
092
053
013
Low
2.8
On
2.2
Off
Picture Image Audio Function Setup 1
Picture Image Audio Function Setup 1
Picture Image Audio Function Setup 1
Brightness
Contrast
045
Brightness
045
Brightness
045
092
Contrast
092
Contrast
092
Color
070
070
Tint
Sharpness
053
Color
Tint
Sharpness
Color
Tint
Sharpness
013
Color Temperature
Black Enhancement
Gamma
Noise Reduction
070
053
013
Color Temperature
Low
2.8
On
Temperature
2.2
Off
Red
Green
023
053
Blue
053
Blue
053
023
Picture Image Audio Function Setup 1
045
Brightness
045
Contrast
092
070
Contrast
Color
092
Color
Tint
Sharpness
Color Temperature
Black Enhancement
053
Tint
053
013
Sharpness
013
2.2
On
Off
Low
Gamma
Noise Reduction
2.8
2.2
On
Off
*Press "RETURN" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
W
Brightness
Contrast
Color*
X
Black is increased for overall
darkness.
Narrows the gap between light and
dark.
Decrease color level.
Black is decreased for overall
brightness.
Broadens the gap between light and
dark.
Increase color level.
Enhances red and weakens green.
Enhances green and weakens red.
Softens picture
Sharpness picture
Tint*
Sharpness*
Cool
Normal
Warm
User
Temperature
Color
Temperature
Red
Green
Blue
Black Enhancement
Gamma
Noise Reduction
053
070
Color Temperature
Black Enhancement
2.8
Normal
Red
Green
Brightness
Low
013
Temperature
Normal
Picture Image Audio Function Setup 1
Gamma
Noise Reduction
053
Color Temperature
Decrease Red level.
Increase Red level.
Decrease Green level.
Increase Green level.
Decrease Blue level.
Off
Increase Blue level.
Middle
Low
2.8
2.2
On
Off
High
Setup hint
Adjust as desired.
Adjust for maximum visibility to suit the
ambient brightness.
Adjust as desired.
This can be adjusted when receiving the
signal and will be grayed out.
Adjust as desired for photo realistic skin color.
Adjust sharpness of picture depending on the
user’s preference.
Adjust color temperature depending on the
user’s preference. These settings are
independently stored in each of the 4 Color
Temperature modes.
Normally set to Low. Adjusts the black level
compensation.
Normally set to 2.2. Adjust the Gamma level
of picture.
If this is set to On, it helps to reduce the noise
interference visible on the screen.
* Only un available in the RGB input.
21
OPERATING INSTRUCTIONS (continued)
ENGLISH
P
IMAGE MENU
Image
Image
Picture
Audio
Function
Setup 1
Auto Adjustment
H Position
029
V Position
050
Horizontal Clock
Clock Phase
Mode Display
WVGA Type
Vertical Filter
Frequency Mode
Picture Size
050
050
On
Off
On
Off
PC
Movie
FULL
Image
Picture
Off
On
Audio
Function
Setup 1
Auto Adjustment
H Position
029
V Position
050
Horizontal Clock
Clock Phase
Mode Display
WVGA Type
Vertical Filter
Frequency Mode
Picture Size
050
Picture
050
On
Off
On
Off
On
Off
PC
Movie
Full
Image
Audio
Function
Setup 1
Auto Adjustment
H Position
Picture
Image
Audio
Function
Setup 1
029
Auto Adjustment
H Position
029
V Position
050
V Position
050
Horizontal Clock
050
Clock Phase
Mode Display
WVGA Type
Vertical Filter
Frequency Mode
Picture Size
050
Horizontal Clock
Clock Phase
Mode Display
WVGA Type
Vertical Filter
Frequency Mode
Picture Size
Picture
On
Off
On
Off
On
Off
PC
Movie
Full
Image
Audio
Function
050
Off
On
Off
On
Off
PC
Movie
Full
Setup 1
Auto Adjustment
H Position
029
V Position
050
Horizontal Clock
050
Clock Phase
Mode Display
WVGA Type
Vertical Filter
Frequency Mode
Picture Size
050
On
050
On
Off
On
Off
On
Off
PC
Movie
Full
d
*Press “RETURN” button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
W
X
Setup hint
Auto Adjustment*
Press the X button to auto-adjust the display parameters to
optimum.
Adjust automatically for clock, phase and position.
H Position*
Press the W or X button to adjust the display position.
Adjust the horizontal display position.
V Position*
Press the W or X button to adjust the display position.
Adjust the vertical display position.
Horizontal Clock
Reduces the dot clock
frequency (shrinks the right
side).
Increases the dot clock frequency
(expands the right side).
Adjust for maximum character clarity.
Clock Phase*
Slows the dot clock. Phase.
Advances the dot clock Phase.
Adjust for clear character visibility.
(* Only available in RGB input)
22
*Press “RETURN” button to return to Main Menu, then press “MENU” button to exit OSD.
X
Setup hint
Mode Display*
On
Off
This can display the Input Signal Screen Display every time the
input mode and signal mode are changed.
Set to Off if the Input Signal Screen Display is not needed when
switching signals.
WVGA Type*
On
Off
This is only available for W-VGA signal.
When it is set to On, the display area mode can be selected Full or
Real.
Off
Turn On when concerned about screen flicker.
On
Vertical Filter*
PC
Frequency Mode*
Picture Size
Full
Normal
Movie
Cinema
Set to Movie when viewing moving images on a personal computer.
Panoramic
Change picture size by pressW or X button.
17
Refer to Size Switching
* Only available in RGB mode
23
ENGLISH
W
Selected characters
ENGLISH
AUDIO MENU
Audio
Picture Image Audio Function Setup 1
Volume
029
Treble
050
Bass
050
Balance
050
On
Mute
Audio Source
Main
Off
Sub
Picture Image Audio Function Setup 1
Picture Image Audio Function Setup 1
Volume
029
Volume
029
Treble
050
Treble
050
Bass
050
Bass
050
Balance
050
Balance
Mute
On
Audio Source
Main
Off
Mute
Sub
Audio Source
050
On
Main
Off
Sub
*Press "RETURN”" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
W
X
Setup hint
Volume
Suppresses volume.
Enhances volume.
Adjust to taste.
Treble
Suppresses treble.
Enhances treble.
Adjust to taste.
Bass
Suppresses bass.
Enhances bass.
Adjust to taste.
Balance
Suppresses right-side sound.
Suppresses left-side sound.
Mute
Audio Source*
On
Main
Off
Sub
Adjust to taste.
To turn off the audio.
Select audio of Main picture or Sub picture
*Only available in the PIP mode.
24
ENGLISH
OPERATING INSTRUCTIONS (continued)
FUNCTION MENU
Function
Picture Image Audio Function Setup 1
PIP H Position
050
PIP V Position
PIP V Layout
050
Picture Image Audio Function Setup 1
Picture Image Audio Function Setup 1
PIP H Position
PIP H Position
050
PIP V Position
050
050
PIP V Position
050
PIP Layout
PIP Layout
Window Layout
SINGLE
Main Picture
AV1
Picture Image Audio Function Setup 1
PIP H Position
050
PIP V Position
050
PIP Layout
Window Layout
Main
Main
Sub
SINGLE
PIP
SINGLE
Main Picture
AV1
Sub Picture
AV3
Sub
PBP
POP 5
POP 12
*Press "RETURN”" button to return to Main Menu, then press “MENU” button to exit OSD.
W
Selected characters
X
Setup hint
PIP H Position
Use the
WXbuttons to adjust pictures to the right or left positions.
Change PIP horizontal display position.
PIP V Position
Use the
S Tbuttons to adjust pictures to the up or down positions.
Change PIP vertical display position.
PIP Layout
Window Layout
Main Picture
SINGLE
PIP
Composite AV1
PBP
POP 5
Svideo AV1
POP 12
Change PIP display layout.
Composite AV2
Set the input of main picture.
HDMI
Sub Picture
RGB
Svideo AV1
AV4
AV3
Composite AV1
Svideo AV2
Svideo AV2
Set the input of sub picture.
RGB
HDMI
AV3
AV4
Composite AV2
25
ENGLISH
FUNCTION SETTINGS (continued)
P I P C o m b i n a t i o n Ta b l e
Available signals are limited in PIP mode as shown in the table below.
PIP or PBP
Sub Source
Input terminal
AV1
Composite
AV1 Composite
AV2
Composite
AV3
component
AV4
component
RGB
HDMI
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
AV2 Composite
Ϥ
AV3 component
Ϥ
Ϥ
AV4 component
Ϥ
Ϥ
Ϥ
RGB
Ϥ
Ϥ
Ϥ
Ϥ
HDMI
Ϥ
Ϥ
Ϥ
Ϥ
Ϥ
AV4
component
RGB
Main Source
Ϥ
POP5 or POP12
Sub Source
Input terminal
AV1
Composite
AV2
Composite
AV3
component
Ϥ
AV1 Composite
AV2 Composite
Ϥ
AV3 component
Ϥ
Ϥ
AV4 component
Ϥ
Ϥ
RGB
Ϥ
Ϥ
HDMI
Ϥ
Ϥ
Main Source
NOTE
z
z
26
Please be careful since image retention will occur if display is left in the PIP display state for a long period of time.
It is normal condition if the sub source is slightly dim while the PIP function is on.
HDMI
ENGLISH
SETUP1 MENU
Setup 1
Picture Image Audio Function Setup 1
Language
English
050
Off Timer
Screen Saver
Screen Wipe
Off
Standby White
Off
Inverse
Off
Off
Off
Power Saving
Normal
Panel Lift
Picture Image Audio Function Setup 1
Language
English
050
Off Timer
Screen Saver
Screen Wipe
Off
Standby White
Off
Off
Off
Inverse
Off
Power Saving
Normal
Panel Lift
*Press "RETURN" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected
characters
Language
W
English
Off Timer
Screen Saver
X
Français
0
Espanõl
Sets the language for the OSD.
180
15 Min.
5 Min.
Off
Setup hint
Set the display off time of unit 0 ~ 180 min.
30 Min.
This moves the picture around the screen in small amounts, at set intervals, to
reduce the panel image retention. This is where stationary objects such as
screen logos; leave a slight image visible after they should have disappeared.
Screen Wipe
Off
30 Min.
60 Min.
This is used to reduce the panel image retention that can occur with stationary
pictures by the white field signal. Select 30. Min or 60 Min. (time limit operation)
and press the OK button. Press the MENU button on the remote control to
return to normal viewing.
Standby White
Off
30 Min.
60 Min.
This function is also provided against the image retention. If time is set for this
item, the screen changes into the white pattern when the monitor enters power
save mode, and it will continue for the period of setting time.
Off
On
60 Min.
Inverse
Panel Life
Normal
Extend 1
Extend 2
This function can change each level of RGB signal invert to reduce the panel
image retention. When this function is required. Select On (continuous
operation) or 60Min. (time limit operation) and press the OK button. And press
the Menu or Return button to exit.
This function is to suppress the contrast of the screen regardless of the
Contrast setting in the Picture Menu. By this control, power consumption can be
reduced or degradation of a panel can be mitigated. The order of power
consumption is Extend 2 Extend 1 Normal.
27
SETUP2 MENU
ENGLISH
Setup 2
Image Audio Function Setup1 Setup 2
System Reset
On
On
On
Freeze Mode
Black Side Panel
Control Panel Lock
Off
Off
Off
Image Audio Function Setup1
Image Audio Function Setup 1 Setup 2
Setup 2
System Reset
System Reset
Freeze Mode
On
Off
Freeze Mode
Black Side Panel
Control Panel Lock
On
On
Off
Off
Black Side Panel
Control Panel Lock
ON
ON
ON
OFF
OFF
OFF
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected
characters
W
X
System Reset
Freeze Mode
Black Side Panel
Control Panel Lock
28
Setup hint
Reset the parameters of above items back to factory setting by pressing the OK
button.
On
Off
On
Off
On
Off
Freeze the picture immediately.
This turns the gray sidebars On/Off when watching normal mode screen size
area. It is always set to Off when the monitor powered On. It is recommended to
set to Off to reduce the panel image retention.
Turn On to lock fuction of control Panel.
Automatic Store
Approximately 1 sec. after adjustment is completed; the adjustments will be recorded as shown in the table below.
Menu
Display
Registration condition
Menu
Brightness
Contrast
Function
Color
Sharpness
For every input, 1 setting is registered.
PIP V Position
PIP Layout
Off Timer
Screen Saver
Black Enhancement
Setup 1
Gamma
Screen Wipe
Noise Reduction
Standby White
Auto Adjustment
Inverse
H Position
Panel Life
V Position
System Reset
Horizontal Clock
Clock Phase
Mode Display
1 setting is registered.
Language
Color Temperature
Image
Registration condition
Window Layout
Tint
Picture
Display
PIP H Position
Setup 2
For RGB input and another input, 1
setting is registered.
1 setting is registered.
(not registered)
Freeze Mode
Black Side Panel
1 setting is registered.
Control Panel Lock
WVGA Type
x The previously recorded items will be lost.
x The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals where all the
elements are the same or similar will be handled as the same signal.
Vertical Filter
Frequency Mode
Picture Size
Volume
Treble
Audio
For every input, 1 setting is registered.
Bass
Balance
1 setting is registered.
Mute
For every input, 1 setting is registered.
29
ENGLISH
OTHER FEATURES
ENGLISH
OTHER FEATURES (continued)
Signal Check (RGB Input)
Changes in the signal status are displayed on the screen.
Status
Display
Action
When Mode display is set to ON, A guide is displayed for the input
the input signal is switched.
terminal.
When the sync signal is no
longer detected.
A guide displays NO SIGNAL.
When the input signal does not
match the monitor specifications
or is in an unstable status.
A guide displays OUT OF
RANGE.
Γ
Recheck the personal computer
power switch status and the
connection status.
RGB
Recheck the input signal
specifications.
36
~ 37
NO SIGNAL
RGB
OUT OF RANG
RGB
30
Image Retention can be an issue for any plasma display, and is caused by displaying fixed (non-moving) images for extended periods of time. If you follow this
simple guideline below you will enjoy a high quality picture for many years to come.
Examples of Image Retention
4x3 Image Display
“Letterbox” Image
Display
“On-Screen Display”
Hitachi has included a number of features, which help to reduce image retention. Please refer to the user manual for this mode for additional instructions on how
to use these features. To avoid image retention, please follow these simple guidelines.
Activate the Screen Saver Mode.
Use Aspect Ratio modes that completely fill the screen with picture.
- Make sure 4 x 3 aspect ratio and letterbox images are not displayed more than 15 of total viewing time.
Avoid using split screen (PIP) modes for long periods of time.
Do not display still images, such as menus from game consoles, PCs or logos, on the monitor screen for long periods of time.
Reduce the “Contrast” level setting to the lowest acceptable setting.
NOTE
About screen defects
x High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright spots (points that are
too bright) in some cases. These do not indicate a malfunction.
About residual images
x In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will disappear and return to
normalcy. This is not a malfunction.
About the panel screen
x Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface may rise in some
cases. Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface but avoid strong impact because
there is still danger of glass breakage.
About screen defects
31
ENGLISH
IMAGE RETENTION
ENGLISH
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Self servicing can be hazardous.
ʳ
Symptom
Point to check
Ɣ There is no picture and the indicating lamp is off.
In RGB mode, the message “NO SIGNAL” is
displayed.
Ɣ In Video mode, the message “NO SIGNAL” is
displayed.
Ɣ There is no picture and the indicating lamp lights
orange.
Ɣ
NO SIGNAL
Ɣ The message “OUT OF RANGE” is displayed.
OUT OF RANGE
Ɣ The indicating lamp is lit normally but there is no
picture.
See Page
Ɣ Check to see that the power cable is properly connected.
Ɣ Press the main switch.
15
No sync signal is detected.
Ɣ Check that the signal cable is properly connected.
Ɣ Make sure that the computer, imaging equipment, etc., is turned on.
Ɣ Make sure the computer is not in power-save mode.
Ɣ Ensure that the input selection matches the connection terminal.
13
An input signal is received abnormally.
Ɣ Ensure that the input signal matches the monitor specifications.
Ɣ Check to see that the signal cable is properly connected.
13
Ɣ Check the contrast and brightness settings (adjust them for higher
contrast and brightness).
Ɣ Check to see that the signal cable is properly connected.
16
14
14
21
13
14
Ɣ The display image appears slanted.
Text displayed across the screen appears vertically
streaked, with the characters in vertical columns
blurred.
Ɣ Text displayed across the screen appears blurred.
A fine pattern flickers when displayed on the screen.
Ɣ The remote control does not work.
Ɣ Adjust the clock frequency and the phase. (Adjust the clock frequency
first, the dot clock phase next.)
(RGB input)
Ɣ Adjust the clock phase till the desired clarity is obtained.
(RGB input)
Ɣ Ensure that the batteries in the remote control are inserted with
the correct polarity.
Ɣ Check to see that the batteries in the remote control are functional.
ʳ
32
22
34
22
34
11
TROUBLESHOOTING (continued)
Symptom
y The temperature of the display panel surface is high.
Point to check
y The plasma display panel is lighting the phosphors by the discharge of
internal radiation. In some cases, this may cause the temperature of the
panel surface to increase. Please note that this is not a malfunction.
See Page
-
y There are locations on the screen that are different from the y High-precision technology is used to manufacture the plasma display panel,
periphery(*)
however in some cases; there are minor defects in some parts of the screen.
* Points that do not light, points with brightness different
Please note that this is not a malfunction.
from that of the periphery, points with color different from
that of the periphery, etc.
-
y Vertical stripes appear, depending on the screen contents. y The plasma display panel is lighting the phosphors on it by the discharge of
internal radiation. Depending on the screen contents, in rare cases this may
cause vertical stripes to appear because of failure to light. Please note that
this is not a malfunction.
-
y Coarse horizontal stripes appear in16:9 display.
y Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
y Flickering in the form of horizontal lines oscillating up and
down.
(RGB INPUT only)
y If the direct frequency from the computer is below 85Hz, try a higher
frequency (upper limit 85Hz). There may be a slight attenuation of the current
image.
-
y The top of the monitor heats up.
y When used for long periods of time, the top surface of the monitor may heat
up. This is not a malfunction.
-
y Text characters are displayed with varying thicknesses.
y The thicknesses of characters and lines may vary if images with a vertical
resolution greater than 480 lines are displayed; however this is not a
malfunction.
-
y The ambient temperature of the monitor may be low. When used in the
ambient temperatures less than about 15 degrees, it may cause lower
luminance. It happens in an operation of the panel protect circuit, and this is
not a malfunction. The luminance will recover by turning on electricity for a
while.
-
y The brightness contrast in the display seems not bright
enough.
ENGLISH
Symptoms That Seemingly Appear to be Failures(continued)
22
y The screen becomes dark and the images cannot be seen y This sometimes occurs when a component output VTR such as the 480i is
during VTR special playback (fast forward, rewind).
connected.
This is not a malfunction; therefore, please take note that this may occur.
When it does occur, change to composite output, or S.video output.
33
Actions to Correct Abnormal Displays (RGB Input)
Corrections d'affichage anormales RVB 1 seulement
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. (only
for RGB)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1).
The display image appears flowing (Figure 2) (RGB input).
Example
Figure 1
Vertical Streaks
Before adjustment.
Some characters are blurred.
After adjustment.
All characters appear
crisp now.
After adjustment.
All characters are
blurred.
Adjustment
procedure
1) Press the MENU button. The Main Menu will be displayed.
2) Press the OK key and W Xbutton then Select Image.
3) Press the S T SELECT button and select Auto Adjustment.
4) Press the X button to auto configuration.
When adjustment is not possible with Auto Adjust:
5) Press the MENU button. The Main Menu will be displayed.
6) Press the OK key and W Xbutton and select Image.
7) Press the S TSELECT button and select Frequency Mode.
8) Press theX or W buttons and search for clear characters over the entire screen.
9) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
z
The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (Figure 2).
A fine pattern flickers when displayed on the screen (Figure 3).
Example
Figure 2
Adjustment
procedure
1) Press the MENU button. The Main Menu will be displayed.
2) Press the W Xbutton and Select Image.
3) Press the S TSELECT button and select Auto Adjustment.
4) Press the X button to auto configuration.
Before adjustment
After adjustment
Figure 3
Before adjustment
After adjustment
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the OK key andW X button and select Image.
7) Press the S TSELECT button and select Clock PHASE.
(Displays fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
8) PressX or W buttons to make the text appear clean across the
screen.
34
9) Press Xor W buttons to make the text appear without flickering.
ENGLISH
TROUBLESHOOTING (continued)
PRODUCT SPECIFICATIONS
Panel
Display
dimensions
Approx. 42 inches (920 (H) x 518 (V) mm, diagonal 1059mm)
Resolution
1024 (H) x 1024 (V) pixels
Net dimensions
(excluding Speakers/Stand)
Net weight
(excluding Speakers/Stand)
Ambient
conditions
ENGLISH
SPÉCIFIC AT ION S DU PR ODUIT
1030 (W) x 636 (H) x 91 (D) mm
34kg
Temperature
Operating: 5°C to 35°C, Storage: -15°C to 60°C
Relative humidity
Operating: 20
to 80 , Storage: 20
Power supply
AC100-240 V, 50/60Hz, 340 W
Audio output
10W
to 90
(non-condensing)
10W (6 Ÿ) (Without speaker)
(RGB input)
Input signals
Input terminals
Anolog RGB analog input terminal (D-sub 15-pin)
Audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V
Sync signals
H/V separate, TTL level 2k Ÿ
H/V composite, TTL level 2k Ÿ
Sync on green, 0.3 Vp-p 75 Ÿ
Recommended signal
26 modes
37
(Video input)
Input terminals
AV1 : Composite video input terminal(RCA)
AV1 S: S video input teminal
AV1 : L/R audio input terminal(RCA)
AV2 : Composite video input terminal(RCA)
AV2 S: S video input teminal
AV2: L/R audio input terminal(RCA)
AV3 : Component (YPbPr) input terminal(RCA)
AV3 : L/R audio input terminal (RCA)
AV4 : Component (YPbPr) input terminal (RCA)
AV4 : L/R audio input terminal (RCA)
HDMI: HDMI input terminal
Video signals
AV1 : NTSC-M, PAL-N
AV2 : NTSC-M, PAL-N
AV3 : 480i, 480p, 720p/60, 1080i/60
AV4 : 480i, 480p, 720p/60, 1080i/60
HDMI: 18 modes 37
Input signals
Output Signal
OUTPUT (MONITOR): composite video output terminal (RCA)
OUTPUT (MONITOR): L/R audio output terminal (RCA)
Recommended signal
24 modes
37
38
x The monitor takes at least 30 minutes to attain the maximum picture quality.
35
ENGLISH
PRODUCT PECIFICATIONS (Continued)
Signal Input
RGB Input (D-sub 15-pin connector)
Pin
Input signal
1
R
2
G or sync on green
3
B
4
No connection
5
No connection
6
R.GND
7
G.GND
x When different kinds of input signals are simultaneously input to the
monitor via a graphics board or the like, the monitor will automatically
select the signals in the following priority order:
8
B.GND
9
No connection
Sync signal type
Priority
10
GND
H/V separate sync.
1
11
No connection
H/V composite sync.
2
12
SDA
sync.on Green *
3
13
H. sync or H/V composite sync
14
V.sync. V.CLK
15
SCL
Frame
GND
page, there may be instances when correct display is not possible. In
this case, use H/V separate sync, or H/V composite sync.
HDMI Input
Pin
1
Input signal
Pin
Input signal
TMDS Data2
11
TMDS Clock Shield
TMDS Clock-
2
TMDS Data2 Shield
12
3
TMDS Data2-
13
CEC
14
Reserved(N.C. on device)
4
TMDS Data 1
5
TMDS Data1 Shield
15
SCL
6
TMDS Data1-
16
SDA
17
DDC/CED Ground
7
TMDS Data0
8
TMDS Data0 Shield
18
9
TMDS Data0-
19
10
TMDS Clock
5V Power
Hot Plug Detect
S-input connector pin specifications
Pin
36
Input signal
1
Y
2
Y-GND
3
C
4
C-GND
Frame
GND
*Even in the case of the recommended signals shown on the following
PRODUCT SPECIFICATIONS (continued)
ENGLISH
Recommended Signal List
With Analog RGB signal input (RGB input)
Signal mode
No.
Signal name
Resolution
Vertical frequency
(Hz)
1
2
VGA
640 x 400
640 x 480
70.08
59.94
3
W-VGA
Horizontal frequency
(kHz)
Dot clock frequency
(MHz)
31.47
31.47
25.18
25.18
864 x 480
59.94
31.47
34.24
4
640 x 480
72.81
37.86
31.50
5
640 x 480
75.00
37.50
31.50
6
7
640 x 480
800 x 600
85.01
56.25
43.27
35.16
36.00
36.00
8
800 x 600
60.32
37.88
40.00
9
800 x 600
72.19
48.08
50.00
10
800 x 600
75.00
46.88
49.50
11
12
800 x 600
1024 x 768
85.06
60.00
53.67
48.36
56.25
65.00
13
1024 x 768
70.07
56.48
75.00
14
1024 x 768
75.03
60.02
78.75
15
1024 x 768
85.00
68.68
94.50
16
17
1152 x 864
1280 x 1024
75.00
60.02
67.05
63.98
108.00
108.00
18
1280 x 1024
75.03
79.98
135.00
19
1280 x 1024
85.02
91.15
157.50
20
1600 x 1200
60.00
75.00
162.00
21
22
640 x 480
832 x 624
66.67
74.55
35.00
49.72
30.24
57.28
23
VESA
Macintosh
24
25
26
W-XGA
1024 x 768
74.93
60.24
80.00
1152 x 870
75.06
68.68
100.00
1280 x 768
59.833
47.986
81.00
1280 x 768
69.997
56.137
94.76
Remark
WVGA Type: On
x The type of video board or connecting cable used, may not allow for correct display adjustment of Horizontal Position, Vertical Position, Horizontal Clock
and Clock Phase.
x The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
x The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities. Note
that different signals having all these elements alike may be handled as the same signal.
x Displaying images with more than 512 lines of vertical resolution at Full display (compressed display) can result in the interpolation of stripes.
With HDMI input
No.
1
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
Dot clock frequency
(MHz)
640 x 480
70.08
31.47
25.18
640 x 480
59.94
31.47
25.18
864 x 480
640 x 480
59.94
72.81
31.47
47.86
34.24
31.50
5
640 x 480
75.00
37.50
31.50
6
640 x 480
85.01
43.27
36.00
7
800 x 600
56.25
35.16
36.00
8
800 x 600
60.32
37.88
40.00
800 x 600
72.19
48.08
50.00
10
800 x 600
75.00
46.88
49.50
11
800 x 600
85.06
53.67
56.25
12
1024x 768
60.00
48.36
65.00
13
1024x 768
70.07
56.48
75.00
14
1024x 768
75.03
60.02
78.75
2
3
4
9
VGA
W-VGA
VESA
15
480i
720 x 480
59.94
15.73
27.00
16
480p
720 x 480
59.94
31.47
27.00
17
1080i/60
1920 x 1080
60
33.75
74.25
18
720p/60
1280 x 720
60
45.00
74.25
x The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities. Note
that different signals having all these elements alike may be handled as the same signal.
x Displaying images with more than 512 lines of vertical resolution at Full display (compressed display)can result in the interpolation of stripes
x Make sure that the signal of the equipment to be connected is compatible with the specifications of this list.
37
With Composite Input and S-video Input (AV1 and AV2 input)
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
1
NTSC-M
525
59.94
15.73
2
PAL-N
625
50
15.63
Horizontal
frequency (kHz)
Remarks
With Component YPb, Pr input (AV3 and AV4 input)
No.
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
1
480i
480
59.94
15.73
2
480p
480
59.94
31.47
3
1080i/60
1080
60
33.75
4
720p/60
720
60
45.00
Remarks
x The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities. Note
that different signals having all these elements alike may be handled as the same signal.
38
ENGLISH
No.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement