advertisement
Qty.
Item No.
HOBART DISPOSER
SELECTOR CHART
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
FOODWASTE
DISPOSERS
A SIZE TO SOLVE ANY
FOODWASTE PROBLEM…
A disposer installed at each work station, in addition to the soiled dish table unit, provides the maxim u m o f c o n v e n i e n c e a n d sanitation. Foodwaste is ground and flushed through the drain lines instead of accumulating… eliminates handling and storage of filled garbage containers.
The Selector Chart is based on disposing of average foodwaste mix. 1 ⁄
2
lb. food waste/person/meal should be used as a guide. If the mix will include a large percentage of bones or other hard materials, specify a larger model disposer or additional units.
Refer to Hobart Foodwaste Disposer specification sheets for wide selection of accessories and controls.
Specifications, Details and Dimensions on
Reverse Side.
FD3-50 ( 1 ⁄
2
H.P.)
FD3-75 ( 3 ⁄
4
H.P.)
FD3-125 (1 1 ⁄
4
H.P.)
Shown with short upper housing.
MEALS PER DAY
HOBART DISPOSER SELECTOR CHART
200 to
300
300 to
500
500 to
1000
1000 to
2000
RESTAURANT
HOTEL
HOSPITAL
CAFETERIA
COMMISSARY
SCHOOL
POINT OF
ORIGIN
Soiled Dish Table
Soiled Dish Table
2000 to
4000
FD3-125 FD3-150 FD3-200 FD3-300 FD-500
FD3-75 FD3-125 FD3-150 FD3-200 FD3-300
Veg.–Salad Prep. Area FD3-75 FD3-125 FD3-125 FD3-150 FD3-200
Scullery Area FD3-50 FD3-75 FD3-75 FD3-75 FD3-125
FD3-150 (1 1 ⁄
2
H.P.)
FD3-200 (2 H.P.)
FD3-300 (3 H.P.)
F-7685 – Hobart Disposer Selector Chart
FD-500 (5 H.P.)
Page 1 of 2
HOBART DISPOSER
SELECTOR CHART
HOBART FOODWASTE
DISPOSER FEATURE
1.
Two hardened stainless steel removable CUTTER
BLOCKS can be indexed for new cutting edges or replaced through throat of disposer.
2.
BREAKER BLADE speeds grinding, prevents objects from riding at center of flywheel.
3.
Ni-Resist FLYWHEEL is precision machined and balanced, has slots which undercut stationary shredder ring teeth to assure that particles are cut to proper size before passing to drain line. STATIONARY SHREDDER RING is cast Ni-Hard, has a minimum of 4 machine ground primary action breaker bars and a minimum of 40 secondary action grinding teeth.
4.
Heavy duty face type WATER SEAL consists of a sintered bronze mating ring and a spring loaded carbon ring insert in a chemical resistant rubber bellows. Mating surfaces are protected by being recessed into the flywheel.
5.
Heavy aluminum GRIND and DISCHARGE HOUSINGS reduce operating sound level.
6.
Should moisture pass seal, a FLINGER, and weep hole are provided to insure immediate removal. A lip type OIL
SEAL (beneath bearings) is an “added protection” water seal.
BEARINGS for upper shaft support are permanently lubricated. Models FD3-50 through FD3-300 have ball bearings.
Model FD-500 has a matched set of tapered roller bearings.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DUAL DIRECTIONAL GRINDING…automatic reversing of disposer’s direction of rotation when installed with Control
Group 2 or 3. Increases life and efficiency of grinding elements by dispersing the wear factor. Will reverse unit, freeing it up in case a jamming situation occurs.
CONES…all models FD3-50 through FD-500 fit the same large 7 inch throat opening diameter. Cones of hydraformed stainless steel, 18 inch bowl diameter is standard; 15 inch is optional. Both feature a dual directional water inlet for flushing waste into the disposer.
VINYL ISOLATING RING eliminates metal to metal contact and prevents vibration and noise transmission. Sink and trough mounting accessories are also available.
ADAPTERS are available to install Hobart Disposers on existing Cones (See Form F-7543).
THERE IS NO SUBSTITUTE FOR
SUPERIOR DESIGN, QUALITY
AND RUGGED CONSTRUCTION.
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
FORM F-7685 (REV. 8/03)
Page 2 of 2
R
701 RIDGE AVENUE
TROY, OHIO 45374-0001
LITHO IN U.S.A. (H-01)
Printed On Recycled Paper
F-7685 – Hobart Disposer Selector Chart
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement