advertisement
Installation Guide
Included Installation Instructions
Network Camera
Model No.
WV-SW155
WV-SW155M/ WV-SW155MA
WV-SW152/ WV-SW152M
WV-SW155
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
This document is the Installation Guide for use in other countries except Japan.
2
CAN ICES-3(A)/NMB-3(A)
For Canada
For U.S.A
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
For U.S.A
The model number and serial number of this product may be found on the surface of the unit.
You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
For Europe
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC.
Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit der folgenden
Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen der Richtlinie 2004/108/EC.
Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présente déclaration est conforme á la norme spécifiée ou à tout autre document normatif conformément aux dispositions de la directive
2004/108/CE.
Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia esta declaración está conforme con la norma u otro documento normativo siguiendo las estipulaciones de la directiva 2004/108/CE.
Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle disposizioni della direttiva
2004/108/CE.
Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen van Richtlijn 2004/108/
EC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standard eller andre normative dokumenter i følge bestemmelserne i direktiv 2004/108/EC.
Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i
överensstämmelse med standarddokument eller annat normativt dokument som framställs i direktiv 2004/108/
EC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/EC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsene i direktiv 2004/108/EC.
Contents
3
4
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
6) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
7) Only use attachments/accessories specified by the manufacturer.
8) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
S3125A
9) Unplug this apparatus during lightning storms or when unused for long periods of time.
10) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Disclaimer of warranty
IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,
SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT
OPERATION OF THE USER;
(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
5
6
Preface
The network cameras WV-SW155/WV-SW155M/WV-SW155MA/WV-SW152/WV-SW152M are designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (sheltered outdoor).
By connecting to a network (LAN) or the Internet, images from the camera can be monitored on a
PC via a network.
SW155
SW155M
• Maximum image capture size: 1280x960 (Aspect 4:3), 1280x720 (Aspect 16:9)
SW152 SW152M
• Maximum image capture size: 800x600 (Aspect 4:3), 640x360 (Aspect 16:9)
Note:
• It is necessary to configure the network settings of the PC and its network environment to monitor images from the camera on the PC. It is also necessary to install a web browser on the
PC.
Main functions
Introduction of Super Dynamic
(
☞
Operating Instructions (included in the CD-ROM))
Super Dynamic compensates brightness on a pixel-to-pixel basis so that it produces clearer images even if objects have various illumination intensities.
H.264 and JPEG triple encoding
The 2 types of H.264 stream outputs and the JPEG output can be simultaneously provided.
Power over Ethernet function
When connecting with a PoE (Power over Ethernet) device, power will be supplied by simply connecting a LAN cable. (IEEE802.3af compliant)
Adaptive darkness correction mode
Corrects the blacked-out parts of dark areas of objects that have different illumination intensities.
SDHC/SD memory card slot equipped
It is possible to save H.264 videos and JPEG images on the SDHC/SD memory card manually at an alarm occurrence, during the period of the schedule, or on a web browser. It is also possible to save JPEG images at a network failure occurrence. (Download is possible.)
(Recommended SDHC/SD memory card
☞
page 37)
About the user manuals
There are 2 sets of operating instructions for the WV-SW155, WV-SW155M, WV-SW155MA,
WV-SW152, WV-SW152M as follows.
• Installation Guide: Explains how to install and connect devices.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera.
SW155, SW155M, SW155MA, SW152, SW152M shown in the instructions and illustrations used in these operating instructions indicates the WV-SW155, WV-SW155M, WV-SW155MA, WV-SW152,
WV-SW152M.
The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.
English screens are used in these operating instructions.
About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
SW155
SW155M
: The functions with this notation are available when using the model WV-SW155.
: The functions with this notation are available when using the model WV-SW155M/
SW152
SW152M
WV-SW155MA.
: The functions with this notation are available when using the model WV-SW152.
: The functions with this notation are available when using the model WV-SW152M.
System requirements for a PC
System requirements for a PC
CPU: Intel
®
Core
TM
2 Duo 2.4 GHz or faster recommended
Memory:
Network interface:
512 MB or more (A minimum of 1 GB memory is required when using
Microsoft
®
Windows
®
7 or Microsoft
®
Windows Vista
®
.)
10BASE-T/100BASE-TX 1 port
Monitor: Image capture size: 1024 x 768 pixels or more
Color: 24-bit True color or better
OS: Microsoft
®
Windows
®
7
Microsoft
®
Windows Vista
®
Microsoft
®
Windows
®
Web browser: Windows
®
XP SP3
Internet Explorer
®
9.0 (32-bit)
Windows
®
Internet Explorer
®
Windows
®
Internet Explorer
®
8.0 (32-bit)
7.0 (32-bit)
Microsoft
®
Internet Explorer
®
6.0 SP3
7
8
Others: CD-ROM drive
(It is necessary to read the operating instructions and use the software on the provided CD-ROM.)
DirectX
®
Adobe
®
9.0c or later
Reader
®
(It is necessary to view the PDF file on the provided CD-ROM.)
IMPORTANT:
• When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable.
• Microsoft
®
Windows
®
7 Starter, Microsoft
®
Windows Vista
®
Starter and Microsoft
®
Windows
®
XP Professional 64-bit Edition are not supported.
• When using IPv6 for communication, use Microsoft
®
Windows
®
7 or Microsoft
®
Windows
Vista
®
.
Note:
• Refer to "Notes on Windows Vista
®
/ Windows
®
7" on the provided CD-ROM for further information about system requirements for a PC and precautions when using Microsoft
®
Windows
®
7 or Microsoft
®
Windows Vista
®
.
• If using Microsoft
®
Windows
®
XP, screen tearing* may occur when the shooting scene drastically changes (for example, while shooting fast-moving subjects) due to the GDI restrictions of the OS.
* A phenomenon in which portions of the screen are displayed out of alignment
• For information on the operation verification of the supported operating systems and web
browsers, refer to our website at http://security.panasonic.com/pss/security/support/index.html.
Trademarks and registered trademarks
• Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
• Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
• Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
• SDHC Logo is a trademark of SD-3C, LLC.
• iPad, iPhone, and iPod touch are registered trademarks of Apple Inc., registered in the U.S. and other countries.
• Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.
• All other trademarks identified herein are the property of their respective owners.
Copyright
Distributing, copying, disassembling, reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition, exporting any software provided with this product violating export laws is prohibited.
Network security
As you will use this unit connected to a network, your attention is called to the following security risks.
q Leakage or theft of information through this unit
w Use of this unit for illegal operations by persons with malicious intent
e Interference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
• Use this unit in a network secured by a firewall, etc.
• If this unit is connected to a network that includes PCs, make sure that the system is not infected by computer viruses or other malicious entities (using a regularly updated anti-virus program, anti-spyware program, etc.).
• Protect your network against unauthorized access by restricting users to those who log in with an authorized user name and password.
• Apply measures such as user authentication to protect your network against leakage or theft of information, including image data, authentication information (user names and passwords), alarm mail information, FTP server information and DDNS server information.
• After the unit is accessed by the administrator, make sure to close the browser.
• Change the administrator password periodically.
• Do not install the camera in locations where the camera or the cables can be destroyed or damaged by persons with malicious intent.
9
Precautions
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to this product.
Be sure to consult the dealer.
Stop the operation immediately when something is wrong with this product.
When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product has deteriorated, continued use will cause a fire or fall of the product resulting in injury, accidents, or damage to the product.
Turn the power off immediately and contact qualified service personnel for service.
Do not attempt to disassemble or modify this product.
Failure to observe this may cause fire or electric shock.
Consult the dealer for the repair or inspections. resulting in injury.
Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.
Install this product in a location high enough to avoid people and objects from bumping the product.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not strike or give a strong shock to this product.
Failure to observe this may cause fire or injury.
Shock resistance grade (50J IEC60068-2-75 or equivalent) is applied to this product only when it is installed correctly as described in these operating instructions and appropriate shock resistance treatment is applied.
10
Do not insert any foreign objects.
This could permanently damage this product.
Turn the power off immediately and contact qualified service personnel for service.
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury.
Installation work shall be started after sufficient reinforcement.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
Turn the power off when do wiring of this product.
Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire.
The exclusively designed mount bracket shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for installation.
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
Do not use this product in an inflammable atmosphere.
Failure to observe this may cause an explosion
Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
Do not touch this product or the connected cables during thunder. (even in the process of work)
Failure to observe this may cause electric shock.
Turn the power off when cleaning this product.
Failure to observe this may cause injury.
Product disposal/transfer
Data saved on this product or a storage device used with this product may lead to personal information leakage.
When it is necessary to dispose or give this product to someone, even when for repair, make sure that there is no data on this product.
[Precautions for use]
This product has no power switch.
When turning off the power, turn off a PoE hub or remove a network cable.
Cleaning this product body
Be sure to turn off the power before cleaning.
Failure to observe this may cause injury. Do not use strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration.
To keep on using with stable performance
Do not use this product in hot and humid conditions for a long time. Failure to observe this causes component degradation resulting in life shortening of this product.
Do not expose the product to direct heat sources such as a heater.
Cleaning the lens
Use a lens cleaning paper (used to clean camera lenses or lenses of spectacles). When using solvent, use an alcohols solvent and do not use a thinner or a glass cleaner.
Do not touch the dome cover with your bare hands.
A dirty dome cover causes deterioration of picture quality.
Transmission interval
Image transmission interval may become slow depending on the network environment, PC performance, shooting subject, access number, etc.
Handle this product with care.
Do not drop this product, nor apply shock or vibration to the product. Failure to observe this may cause trouble. If a strong shock or vibration is applied to the enclosure, it may cause damage or allow water to enter this product.
About the PC monitor
Displaying the same image on a monitor for a long time may damage the monitor. It is recommended to use a screen-saver.
When an error is detected, this product will restart automatically.
This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.
About SDHC/SD memory card
• Before removing the SDHC/SD memory card, make sure to select “Not use” for
“SD memory card” on the [SD memory card] tab of “Basic” page on the setup menu first. (☞ Operating Instructions
(included in the CD-ROM))
Refer to page 22 for descriptions of how to insert/remove an SDHC/SD memory card.
• When using an SDHC/SD memory card, format it using this product. Recorded data on the SDHC/SD memory card will be deleted when formatted. If an unformatted
SDHC/SD memory card or an SDHC/SD memory card formatted with other devices is used, this product may not work properly or performance deterioration may be caused. Refer to the Operating Instructions
(included in the CD-ROM) for how to format a SDHC/SD memory card.
11
12
• When some SDHC/SD memory cards are used with this product, the product may not work properly or performance deterioration may be caused. Use the SDHC/SD memory cards recommended in page 37.
Code label
The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recommended to paste one of the labels onto the CD-ROM case.
About the MOS image sensor
• When continuously shooting a bright light source such as a spotlight, the color filter of the MOS image sensor may have deteriorated and it may cause discoloration.
Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period, the discoloration may remain.
• When shooting fast-moving subjects or performing panning/tilting operations, objects crossing the shooting area may look to be bending askew.
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE
AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR
OTHER USES IN WHICH IT DOES NOT
RECEIVE REMUNERATION TO (I) ENCODE
VIDEO IN COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”) AND/OR (II)
DECODE AVC VIDEO THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A PERSONAL
ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED TO PROVIDE
AVC VIDEO. NO LICENSE IS GRANTED OR
SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
Flickering
Due to the influence of lighting, flickering may sometimes happen. In this case, select "Indoor scene" for "Light control mode". Select "Indoor scene(50Hz)" or "Indoor scene(60Hz)" in accordance with the power supply frequency in your locality. Refer to the Operating Instructions
(included in the CD-ROM) for further information about the setting.
Under extremely strong lighting, flickering may happen even when "Indoor scene" is selected for "Light control mode".
When the brightness (illuminance) level on the screen is set to a relatively low level with the
[Brightness] buttons, flickering may frequently happen. In such cases, either of the following can reduce flickering.
• Moderate the illumination intensities of objects by changing the camera direction.
• Set the brightness (illuminance) level on the screen to a brighter level with the
[Brightness] buttons.
White-out on images caused by the effect of light control mode
When "Indoor scene" is selected for "Light control mode", the tone of the brighter parts on the screen may be deteriorated than the case when "ELC" is selected.
Color blurring on detailed drawing patterns
When there are detailed drawing patterns on images, color blurring may happen over these parts.
Operating temperature
This product can be used in low temperature outdoor environments that get as cold as
–30 °C {-22 °F}. However, when this product is installed and operated in temperatures below
–20 °C {-4 °F}, normal images may not be obtained immediately after startup. In such a case, connect the power and wait approx.
2 hours, and then connect the power again.
Brightness around the images
The surrounding area of the image may appear slightly dark depending on the shooting subject.
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
This product is designed to be installed under eaves.
Install the product under eaves to avoid direct sunlight.
Be sure to remove this product if it is not in use.
Design and engineer the power supply system to turn on/off the power of this product.
The product has no power switch. When installing the product, use a PoE hub equipped with the ON-OFF switch for servicing.
Installing place
Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment.
• Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
• Install the camera in the foundation area of the architecture or where sufficient strength is assured.
• If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced.
About the network connection
When connecting to a network using the network cable of this product, observe the following.
• When wiring for the network, design and engineer not to be affected by thunder.
• It is impossible to install this product in combination with a pan/tilt head.
Do not place this product in the following places:
• Locations where a chemical agent is used such as a swimming pool
• Locations subject to humidity, dust, steam and oil smoke
• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
• Locations where corrosive gas is produced, locations where it may be damaged by briny air such as seashores
• Locations where the temperature is not within the specified range (page 35).
• Locations subject to vibrations that exceed the railway specifications (EN50155)
• If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced.
Screw tightening
• The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area.
• Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.
• When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.
Procure fixing screws separately.
The screws that secure this product are not supplied. Prepare them according to the material and strength of the area where the product is to be installed.
13
14
Do not remove or loosen the internal camera screws
Do not loosen the internal camera screws.
Otherwise, water exposure may cause damage or malfunction of camera, or camera dropping may result in injury.
Radio disturbance
When this product is used near TV/radio antenna, strong electric field or magnetic field (near a motor, a transformer or a power line), images may be distorted and noise sound may be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with
IEEE802.3af standard.
Router
When connecting this product to the Internet, use a broadband router with the port forwarding function (NAT, IP masquerade).
Refer to the Operating Instructions (included in the CD-ROM) for further information about the port forwarding function.
Time & date setting
It is necessary to set the time & date before putting this product into operation. Refer to the
Operating Instructions on the provided
CD-ROM for descriptions of how to perform the settings.
Major operating controls
<Front view>
Enclosure
<Rear view>
Network cable
Dome cover
Initial set button
SDHC/SD memory card slot
Access indicator
(lit when accessing)
Lens
SD memory card error indicator
(lit when data cannot be saved)
Link indicator
(lit when linking)
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for around 5 seconds or more without releasing the button. Wait around 2 minutes after releasing the button. The camera will start up and the settings including the network settings will be initialized. Do not turn off the power of the camera during the process of initialization. Before initializing the settings, it is recommended to write down the settings in advance.
15
16
Removing the enclosure
IMPORTANT:
• Remove the cover film attached to the dome cover after the camera installation is completed.
After removing the cover film, do not touch the dome cover with your hands.
Cover film z
Loosen the 3 enclosure fixing screws (M3) using the tamperproof screw bit (accessory).
• One of the screws is loosened after taking off the screw cover.
Screw cover
Screw x
Remove the enclosure.
Preparations
When installing the camera on a ceiling or a wall, there are three methods as specified below.
• Directly mounting to a ceiling or a wall
• Use the supplied mount bracket
• Use the one-gang junction box
IMPORTANT:
• Procure 3 screws (M4) to secure the camera or the mount bracket (accessory) to a ceiling or a wall according to the material of the installation area. Do not use wood screws and nails.
For mounting a camera on a concrete ceiling, use an anchor bolt (for M4) or an AY plug bolt
(M4) for securing.
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
• Mount the mount bracket in consideration of the camera angle in accordance with the instructions (
☞
pages 19 and 20).
• Required pull-out capacity of a single screw/bolt is 196 N {44.06 lbf} or more.
• If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced.
The mounting conditions of the camera are described as follows:
Installation place
Appropriate mount bracket
Ceiling/wall (direct mounting)
Ceiling/wall* Mount bracket
(accessory)
Ceiling/wall One-gang junction box
Recommended screw
Number of screw
M4
M4
3 pcs.
3 pcs.
M4 2 pcs.
Minimum pull-out strength (per 1 pc.)
196 N {44.06 lbf}
196 N {44.06 lbf}
196 N {44.06 lbf}
* The conditions for securing the mount bracket to a ceiling or a wall are described here.
17
18
Method of camera installation
Installing the camera directly on the ceiling or wall
Note:
• Use the installation template label (accessory) with the side with the arrow facing you.
• Ceiling installation:
Place the installation template label so that the "" is pointing to the front of the camera (the lens side).
• Wall installation:
Place the installation template label so that the "" is pointing down.
Cable access hole
Tamperproof screw hole
<Connecting the cable through holes opened in the ceiling or wall>
Place the installation template label (accessory) on the ceiling or wall, mark the hole for the cable to be passed through and for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the camera with 3 fixing screws (locally procured). (
☞
Page 26)
<Connecting the cable through the side cable access hole>
Place the installation template label (accessory) on the ceiling or wall, mark the holes for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the camera with 3 fixing screws (locally procured). (
☞
Page 26)
n
Ceiling n
Wall
Using the mount bracket (accessory)
Note:
• When the camera is mounted on the ceiling or wall with a hole for cable running and the cables are passed through a conduit, the mount bracket is used.
• The female thread for conduit is compliant with ANSI NPSM (parallel pipe threads) 3/4" or G3/4 of ISO 228-1.
• Ceiling installation:
The mount bracket shall be mounted with aligning the front side (the lens side) of the camera with the position of the arrow in "".
• Wall installation:
The mount bracket shall be mounted with "" facing upward.
IMPORTANT:
• Installation work shall be such that there is no intrusion of water into the architecture through the joined conduits, or through the hole opened for the ceiling or wall.
19
20
Tamperproof screw hole
Cable access hole
<Connecting the cable through holes opened in the ceiling or wall>
Place the installation template label (accessory) on the ceiling or wall, mark the hole for the cable to be passed through and for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the mount bracket with 3 fixing screws (locally procured). (
☞
Pages 26 and 27)
<Connecting the cable through the side cable access hole>
Place the installation template label (accessory) on the ceiling or wall, mark the holes for the fixing screws (3 places), then open the holes.
Remove the installation template label, and mount the mount bracket with 3 fixing screws (locally procured). (
☞
Pages 26 and 27) n
Ceiling n
Wall
Using a one-gang junction box
• Secure the mount bracket (accessory) to the one-gang junction box built in a ceiling or a wall.
[Mounting hole pattern]
One-gang junction box
83.5 mm {3-9/32"}
Mount bracket (accessory)
Note:
• Ceiling installation:
The mount bracket shall be mounted with aligning the front side (the lens side) of the camera with the position of the arrow in "".
• Wall installation:
The mount bracket shall be mounted with "" facing upward.
21
22
Insert/remove an SDHC/SD memory card
IMPORTANT:
• When inserting an SDHC/SD memory card, make sure the direction.
• Before removing the SDHC/SD memory card, make sure to select “Not use” for “SD memory card” on the [SD memory card] tab of the “Basic” page on the setup menu first. (
☞
Operating
Instructions (included in the CD-ROM)) z
Remove the enclosure. (
☞
Page 16) x
Insert an SDHC/SD memory card fully into the
SDHC/SD memory card slot until a click is heard. c
Attach the enclosure to the camera.
(
☞
Page 31) v
When removing the SDHC/SD memory card from the SDHC/SD memory card slot, remove the enclosure (
☞
page 16), and push the card until a click is heard. After the SDHC/SD memory card is removed, attach the enclosure to the camera again. (
☞
Page 31)
Label side
Connection
Before starting the connection, turn off the power of the devices to be connected.
Check and prepare the required devices and cables for connection.
Note:
• Refer to pages 26 and 27 when using the mount bracket (accessory).
• Refer to pages 26 and 27 when using the conduit.
z
Connect a LAN cable (category 5 or better, straight) between a PoE device (such as a hub) and the network connector of the camera.
<WV-SW155, WV-SW152>
Connect a LAN cable (category 5 or better, straight, STP) between a PoE device (such as a hub) and the network connector of the camera.
Network cable
RJ-45 (female)
<WV-SW155M, WV-SW155MA, WV-SW152M>
Connect a LAN cable (category 5 or better, straight, STP) between a PoE device with M12 connectors (such as a hub) and the network connector of the camera.
Network cable
M12 connector*
* WV-SW155M/WV-SW152M: M12 connector (male)
WV-SW155MA: M12 connector (female)
(This illustration represents WV-SW155MA)
23
24
IMPORTANT:
• Use all 4 pairs (8 pins) of the LAN cable.
• The maximum cable length is 100 m {328 feet}.
• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
• When the LAN cable is disconnected once, reconnect the cable after about 2 seconds. When the cable is quickly reconnected, the power may not be supplied from the PoE device.
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera outdoors. The camera body is waterproof, but the cable ends are not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply waterproof treatment in the following procedure. Failure to observe this or use of a tape other than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunction.
LAN cable
Wind the tape in a half-overlapping manner.
Note:
How to wind the supplied waterproof tape
• Stretch the tape by approx. twice (see the illustration) and wind it around the cable. Insufficient tape stretch causes insufficient waterproofing.
• Make sure to wind the tape so that it does not press down on the hook of the network cable.
• To install this product outdoors, be sure to waterproof the cables.
Waterproof grade (IEC IP66 or equivalent) is applied to this product only when it is installed correctly as described in these operating instructions and appropriate waterproof treatment is applied. The mount brackets are not waterproofed.
Stretch the tape to about twice.
hook
2x
Connection example
PoE device (hub)
LAN cable
(category 5 or better, straight)
LAN cable
(category 5 or better, straight)
PC
LAN cable
(category 5 or better, straight)
<Required cable>
LAN cable (category 5 or better, straight)
IMPORTANT:
• Use a switching hub which is compliant with 10BASE-T/100BASE-TX.
• When connecting WV-SW155M/WV-SW155MA cameras, use a PoE hub with M12 connectors.
25
Installation
Camera mounting
<Installing the camera directly on the ceiling or wall>
z
Remove the enclosure. (3 screws) (
☞
Page 16) x
Connect the cables to the camera. (
☞
Pages 23 and 24)
• Waterproof the connecting portion. (
☞
Page 24) c
Secure the camera with 3 screws (M4) (locally procured).
n
Ceiling n
Wall
26
IMPORTANT:
• Do not touch the lens.
• When tightening the screws, be careful to ensure that the cables does not tangle the cables.
<Using the mount bracket>
z
Connect each cable.
• Apply waterproof treatment to all connections. (
☞
Page 24) x
Connect the conduit attachment (locally procured) to the conduit.
c
Secure the mount bracket to the conduit attachment with the attachment for female thread
(locally procured).
v
Mount the mount bracket to either a ceiling or a wall.
(3 screws (M4) (locally procured)) b
Secure the camera to the mount bracket with 3 fixing screws (accessory).
(Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Attachment for female thread
Camera
Conduit attachment n
Ceiling
Fixing screws Mount bracket Network cable
Conduit n
Wall
<Using a one-gang junction box>
z
Connect each cable.
• Apply waterproof treatment to all connections. (
☞
Page 24) x
Secure the mount bracket to the one-gang junction box. (2 screws (M4) (locally procured)) c
Secure the camera to the mount bracket with 3 fixing screws (accessory).
(Recommended tightening torque: 1.4 N·m {1 lbf·ft})
Mount bracket
Camera
Fixing screws
Network cable
One-gang junction box
27
28
Using the side cable access hole
When installing the camera directly on the ceiling or wall with cables exposed, cut off a portion of the mount bracket to open a cable access hole.
Cut off
Adjustment
z
Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning table and tilting table.
• Attach the lens adjuster (accessory) to the lens and adjust the direction of the lens. Attach the wider end of the lens adjuster to the lens.
• Do not touch the lens with your hand when making adjustments.
• Make adjustments to the direction of the lens while confirming the picture displayed on computer’s monitor.
n
Ceiling
Horizontal position : -20 ° to +20 ° n
Wall
Vertical position : -90 ° to +20 °
Vertical position : -20 ° to +90 °
Horizontal position*
*WV-SW155/WV-SW155M/WV-SW152/
WV-SW152M: -80 ° to +80 °
WV-SW155MA: -90 ° to +90 °
• When adjusting the horizontal angle of cameras mounted to a ceiling, adjust the direction of the lens by moving the lens holding the indentations on the sides of the lens.
29
Note:
• Depending on the vertical/horizontal angle used, the edges of the camera may be projected.
• Use Extra Zoom when you want to adjust the angular field of view on the "Tele" side. When
VGA or a lower resolution is selected, the angular field of view can be adjusted without deterioration in the image quality.
•
SW155 SW155M
:
If the 2x extra zoom is applied when "1280x960" or "1280x720" is selected for the image capture size, the image quality will be deteriorated because the effect of Extra Zoom is not provided.
SW152 SW152M
:
If the 2x extra zoom is applied when "800x600" is selected for the image capture size, the image quality will be deteriorated because the effect of Extra Zoom is not provided.
x
<Adjusting the focus of the lens>
Attach the lens adjuster (accessory), and rotate the lens to adjust the focus of the lens.
• When making adjustments to the focus of the lens, attach the narrower end of the lens adjuster to the lens.
30
When attaching or removing the lens adjuster, squeeze the wider end of the lens adjuster as shown in the illustration to open the narrower end of the lens adjuster.
Note:
• When the focus is difficult to adjust, set the [Zoom] button on the "Live" page to "x2".
Attaching the enclosure
z
Attach the enclosure to the camera by using the tamperproof screw bit (accessory) to tighten the 3 enclosure fixing screws (M3). (Recommended tightening torque: 0.8 N·m {0.59 lbf·ft}) n
Ceiling n
Wall
Screw cover
Enclosure fixing screws
Enclosure fixing screws x
Close the screw cover.
c
Remove the cover film completely.
IMPORTANT:
• When attaching the enclosure the focus may be slightly disturbed. If this occurs, remove the enclosure and make the necessary adjustments.
• Before attaching the enclosure, make sure that the subject is present.
• Securely tighten all the fixing screws (x3) of enclosure. Otherwise, water exposure may cause damage or malfunction of camera, or camera dropping may result in injury.
(Recommended tightening torque: 0.8 N·m {0.59 lbf·ft})
• Remove the cover film from the dome cover.
31
Configure the network settings
Configuring the camera so that it can be accessed from a PC
The following are descriptions for when the camera with default settings is configured. If you are using firewall software on your PC, the Setup Program may not be able to find any cameras on your network. Configure the setting of the camera after temporarily invalidating the firewall software. Contact the network administrator or your Internet service provider for information about configuring the settings of the network.
z
Insert the provided CD-ROM into the CD-ROM drive of your PC.
• The License Agreement will be displayed. Read the Agreement and choose “I accept the term in the license agreement”, and click [OK].
• The launcher window will be displayed. If the launcher window is not displayed, double click the “CDLauncher.exe” file on the CD-ROM.
32
Note:
• Refer to “Using the CD-ROM” in the Operating Instructions on the provided CD-ROM for further information about CDLauncher.
x
Click the [Run] button next to [IP Setting Software].
[Panasonic IP Setting] screen will be displayed. Click the [Network Settings] button after selecting the MAC address/IP address of the camera to be configured.
c
Select the camera you want to configure, and click [Access Camera].
Note:
• When cameras are displayed in [Panasonic IP Setting] screen, click the camera with same
MAC address as the MAC address printed on the camera that you want to configure.
v
If the installation screen of the viewer software “Network Camera View 4S” is displayed, follow the instructions of the wizard to start the installation. (The viewer software is installed from the camera.)
• The “Live” page will be displayed.
• If you cannot install the viewer software “Network Camera View 4S” or if images are not displayed, click the [Install] button next to [Viewer Software] on the launcher window to install the software.
• Perform the [Time & date] settings in the “Setup” - “Basic” page before using the camera.
Note:
• When no image is displayed on the “Live” page, refer to the Troubleshooting in the Operating
Instructions on the provided CD-ROM.
• It is possible to enhance the network security by encrypting the access to cameras using the
HTTPS function. Refer to the Operating instructions on the provided CD-ROM for how to configure the HTTPS settings.
• Click the [Setup] button on the “Live” page, the user authentication window will be displayed.
Enter the default user name and password as follows, and log in.
User name: admin
Password: 12345
• When changing settings related to the network settings, such as connection mode, IP address, and subnet mask, click the [Network Settings] button in [IP Setting Software] screen as shown in step 3, then change each setting.
• Due to security enhancements in “IP Setting Software”, “Network settings” of the camera to be configured cannot be changed when around 20 minutes have passed after turning on the power of the camera. (When the effective period is set to “20 min” in the “Easy IP Setup accommodate period”.)
However, settings can be changed after 20 minutes for cameras in the initial set mode.
• “Network Camera Recorder with Viewer Software Lite” which supports live monitoring and recording images from multiple cameras is available. For further information, refer to our web-
site (http://security.panasonic.com/pss/security/support/info.html).
33
34
Troubleshooting
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below.
Symptom Cause/solution
Reference pages
Power is not turned on.
• Are the PoE device and the network cable of the camera connected using a
LAN cable?
→ Check whether the connection is appropriately established.
• Depending on the PoE device, the power supply will stop when the demanded power exceeds its total power limit for all PoE ports.
→ Refer to the operating instructions of the PoE device in use.
23
Specifications
• Basic
Power source:
Power consumption:
PoE (IEEE802.3af compliant)
PoE 48 V: 56 mA (Class 1 device)
Ambient operating temperature: -30 °C to +50 °C {-22 °F to 122 °F}
Ambient operating humidity:
Waterproof:
Shock resistance:
Dimensions:
Mass:
Finish:
Less than 90 % (no condensation)
Camera: IP66 (IEC60529)
* Only when installation work specified in this book is properly performed and appropriate waterproof treatment is performed
Compliant with 50 J IEC60068-2-75
ø109 mm x 47 (H) mm / 70 (H) mm (Using the mount bracket)
{ø4-9/32 inches x 1-27/32 inches (H)} / {2-3/4 inches (H)}
Approx. 350 g {0.77 lbs}
Approx. 410 g {0.90 lbs} (Using the mount bracket)
Main body: Aluminum die cast, light gray
Dome cover: Clear polycarbonate resin
• Camera
Image sensor:
Effective pixels:
Scanning area:
Scanning system:
Minimum illumination:
SW155 SW155M
1/3-type MOS image sensor
Approx. 1.3 megapixels
4.80 mm (H) × 3.60 mm(V) {3/16 inches (H) x 5/32 inches (V)}
Progressive
Color: 0.8 lx {0.08 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), AGC: On (High))
0.05 lx {0.005 footcandle}
(F2.2, Auto slow shutter: Max. 16/30 s, AGC: On (High))*
BW: 0.6 lx {0.06 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), AGC: On (High))
0.04 lx {0.004 footcandle}
(F2.2, Auto slow shutter: Max. 16/30 s, AGC: On (High))*
Color: 0.6 lx {0.06 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), AGC: On (High))
Minimum illumination:
SW152 SW152M
Super Dynamic:
Dynamic range:
Gain (AGC):
Adaptive black stretch:
Light control mode setting:
ELC (Maximum exposure time): • With Super Dynamic On
Auto slow shutter:
0.04 lx {0.004 footcandle}
(F2.2, Auto slow shutter: Max. 16/30 s, AGC: On (High))*
BW: 0.4 lx {0.04 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), AGC: On (High))
0.03 lx {0.003 footcandle}
(F2.2, Auto slow shutter: Max. 16/30 s, AGC: On (High))*
* Converted value
On/Off
52 dB typ. (Super Dynamic: On, Light control: ELC)
On (High)/ On (Mid)/ On (Low)/ Off
On/Off
Indoor scene (50 Hz/60 Hz)/ ELC
ELC(1/30 s)
• With Super Dynamic Off
ELC(1/30 s), ELC(3/100 s), ELC(3/120 s),
ELC(2/100 s), ELC(2/120 s), ELC(1/100 s), ELC(1/120 s),
ELC(1/250 s), ELC(1/500 s), ELC(1/1000 s), ELC(1/2000 s),
ELC(1/4000 s), ELC(1/10000 s)
Off (1/30 s), Max. 2/30 s, Max. 4/30 s, Max. 6/30 s,
Max. 10/30 s, Max. 16/30 s
35
36
Day & Night (electrical):
White balance:
Digital noise reduction:
Video analytics
Face detection*:
Privacy zone:
VIQS:
Camera title on screen:
Video motion detection
(VMD alarm):
Off/Auto
ATW1/ ATW2/ AWC
High/Low
On/Off (with the XML notification setting)
On/Off (up to 2 zones available)
On/Off
Up to 20 characters (alphanumeric characters, marks)
On/Off
On/Off, 4 areas available
* To use the "XML notification" and "Face detection" functions, you need to install the extension software.
• Lens
Zoom ratio:
Focal length:
Maximum aperture ratio:
Angular field of view:
Adjusting angle:
1x
Extra zoom: 2x (under VGA resolution)
1.95 mm
1:2.2
Horizontal: 104 °
Vertical: 85 °
• Ceiling installation
Horizontal: -20 ° to +20 °
Vertical: -20 ° to +90 °
• Wall installation
Horizontal: <WV-SW155/WV-SW155M/WV-SW152/
WV-SW152M>
-80 ° to +80 °
Vertical:
<WV-SW155MA>
-90 ° to +90 °
-90 ° to +20 °
• Network
Network
SW155 SW152
: 10BASE-T/100BASE-TX, RJ45 connector
SW155M
Resolution
SW155
Resolution
SW152
SW152M
SW155M
SW152M
: 10BASE-T/100BASE-TX, M12 connector
: Aspect ratio: 4:3
H.264 1280×960/ VGA (640×480)/ QVGA (320×240),
Max. 30 fps
JPEG (MJPEG) 1280×960/ VGA (640×480)/ QVGA (320×240),
Max. 30 fps
Aspect ratio: 16:9
H.264 1280×720/ 640×360/ 320×180, Max. 30 fps
JPEG (MJPEG) 1280×720/ 640×360/ 320×180, Max. 30 fps
: Aspect ratio: 4:3
H.264 800×600/ VGA (640×480)/ QVGA (320×240),
Max. 30 fps
JPEG (MJPEG) 800×600/ VGA (640×480)/ QVGA (320×240),
Max. 30 fps
Aspect ratio: 16:9
H.264 640×360/ 320×180, Max. 30 fps
JPEG (MJPEG) 640×360/ 320×180, Max. 30 fps
Image compression method*
1
: H.264
Image quality: Low/Normal/Fine
Transmission type: Unicast/Multicast
Bit rate:
Constant bit rate/Best effort: 64 kbps/ 128 kbps/ 256 kbps/
384 kbps/ 512 kbps/ 768 kbps/ 1024 kbps/ 1536 kbps/
2048 kbps/ 3072 kbps/ 4096 kbps/
8192 kbps
SW155 SW155M
Frame rate:
1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/
30 fps
JPEG (MJPEG)
Transmission interval:
Bandwidth control:
Protocol:
Image quality:
0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/
9 LOW (10 steps: 0-9)
Transmission type: PULL/PUSH
0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying both JPEG and H.264 images.)
Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/
512 kbps/ 768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/
8192 kbps
IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS,
NTP, SNMP, DHCPv6, MLD, ICMP, ARP
IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP,
FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP,
ICMP, ARP
®
Windows OS*
2
*
3
: Microsoft
Browser: Windows
Maximum concurrent
access number:
FTP client:
Multi-screen:
Microsoft
®
Microsoft
®
Windows
Windows
®
®
®
Microsoft
®
Windows
®
7
Windows Vista
®
Compatible SDHC/
SD memory card (option):
Cellular phone compatibility:
Mobile terminal compatibility:
(As of October, 2013)
*4
®
XP SP3
Internet Explorer
Internet Explorer
Internet Explorer
Internet Explorer
14 (Depends on network conditions)
Alarm image transmission, FTP periodic transmission (When the
FTP transmission is failed, backup on an optional SDHC/SD memory card is available.)
Up to 16 camera images can be displayed simultaneously on a multi-screen. (Including the camera itself)
Manufactured by Panasonic
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card: 256 MB, 512 MB, 1 GB, 2 GB
(except miniSD card and microSD card)
JPEG image iPad, iPhone, iPod touch (iOS 4.2.1 or later)
Android
TM
mobile terminals
®
9.0 (32-bit)
®
®
®
8.0 (32-bit)
7.0 (32-bit)
6.0 SP3
*1 Transmission for 2 streams can be individually set in the same compression method.
*2 Refer to "Notes on Windows Vista
®
/ Windows
®
7" on the provided CD-ROM for further information about system requirements for a PC and precautions when using Microsoft
®
Windows
®
Microsoft
®
Windows Vista
®
.
7 or
37
38
*3 When using IPv6 for communication, use Microsoft
®
Windows
®
7 or Microsoft
®
Windows
Vista
®
.
*4 For further information about compatible devices, refer to our website
(http://security.panasonic.com/pss/security/support/info.html).
Standard accessories
Installation Guide (this document) ......................................................1 set
Important Safety Instructions .............................................................1 pc.
Warranty card ....................................................................................1 set
CD-ROM*
1
Code label*
........................................................................................1 pc.
2
......................................................................................1 pc.
Lens adjuster .....................................................................................1 pc.
Plastic cover ......................................................................................1 pc.
The following parts are used during installation procedures.
Fixing screws (M4 x 8 mm) ..............................................................3 pcs.
Installation template label ...................................................................1 pc.
Mount bracket ...................................................................................1 pc.
Tamperproof screw bit .......................................................................1 pc.
Waterproof tape .................................................................................1 pc.
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain the code label.
Optional accessories
User License Accessory (For H.264) ............................ BB-HCA8A
BB-HCA8CE
39
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation of North America
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
© Panasonic System Networks Co., Ltd. 2015
For Europe and other countries:
Panasonic Corporation http://www.panasonic.com
Panasonic System Networks Co., Ltd.
Fukuoka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Cs0515-1085 PGQX1811YA Printed in China
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project