Vector Network Analyzer ¸ZVA

Vector Network Analyzer ¸ZVA
Specifications
Version
02.02
Vector Network Analyzer ¸ZVA
Specifications
September
2006
MEASUREMENT RANGE ............................................................................................................................................................................... 3
MEASUREMENT ACCURACY ....................................................................................................................................................................... 6
EFFECTIVE SYSTEM DATA........................................................................................................................................................................... 7
TEST PORT OUTPUT ................................................................................................................................................................................... 12
TEST PORT INPUT ....................................................................................................................................................................................... 15
ADDITIONAL FRONT PANEL CONNECTORS............................................................................................................................................ 17
DISPLAY........................................................................................................................................................................................................ 17
REAR PANEL CONNECTORS ..................................................................................................................................................................... 18
GENERAL SPECIFICATIONS ...................................................................................................................................................................... 20
ORDERING INFORMATION ......................................................................................................................................................................... 23
2
®
Vector Network Analyzers R&S ZVA
Version 02.02, September 2006
Specifications are valid under the following conditions:
90 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and all internal
adjustments performed. Data designated „overrange“ and data without tolerance limits is not binding. Unless otherwise stated,
specifications apply to test ports and a nominal source power of –10 dBm.
Measurement range
Impedance
Test port connector
Number of test ports
Frequency range
Static frequency accuracy
Frequency resolution
Number of measurement points
Measurement bandwidths
®
Dynamic range of R&S ZVA8
(without optional step attenuators
and without optional direct
generator/receiver access)
®
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA40
®
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA40
®
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA40
without optional oven quartz
with optional oven quartz
50 Ω
type N, female
3.5 mm, male
2.92 mm, male
2 or 4
2 or 4
2 or 4
300 kHz to 8 GHz
10 MHz to 24 GHz
10 MHz to 40 GHz
–6
8×10
–7
1×10
1 Hz
2 to 20001
1 Hz to 1 MHz
user-selectable
1/2/5-steps
from PORT 1 to PORT 2 and
from PORT 3 to PORT 4
300 kHz to 5 MHz
>100 dB, typ. 110 dB
5 MHz to 100 MHz
>120 dB, typ. 130 dB
100 MHz to 4 GHz
>130 dB, typ. 140 dB
4 GHz to 7 GHz
>125 dB, typ. 135 dB
7 GHz to 8 GHz
>120 dB, typ. 130 dB
®
Dynamic range of R&S ZVA24
from PORT 1 to PORT 2 and
(without optional step attenuators
from PORT 3 to PORT 4
and without optional direct
10 MHz to 100 MHz
>90 dB, typ. 105 dB
generator/receiver access)
100 MHz to 700 MHz
>105 dB, typ. 120 dB
700 MHz to 2 GHz
>125 dB, typ. 130 dB
2 GHz to 13 GHz
>130 dB, typ. 135 dB
13 GHz to 24 GHz
>125 dB, typ. 130 dB
®
Dynamic range of R&S ZVA40
from PORT 1 to PORT 2 and
(without optional step attenuators
from PORT 3 to PORT 4
and without optional direct
10 MHz to 50 MHz
>90 dB, typ. 100 dB
generator/receiver access)
50 MHz to 500 MHz
>105 dB, typ. 115 dB
500 MHz to 2 GHz
>125 dB, typ. 135 dB
2 GHz to 20 GHz
>130 dB, typ. 140 dB
20 GHz to 24 GHz
>125 dB, typ. 135 dB
24 GHz to 32 GHz
>115 dB, typ. 125 dB
32 GHz to 40 GHz
>110 dB, typ. 115 dB
from PORT 1 to MEAS 2 IN
Dynamic range at optional meas input
300 kHz to 10 MHz
typ. >125 dB
(option direct generator/receiver access)
®
10 MHz to 100 MHz
typ. >135 dB
of R&S ZVA8
100 MHz to 8 GHz
typ. >145 dB
Dynamic range at optional meas input
from PORT 1 to MEAS 2 IN
(option direct generator/receiver access)
10 MHz to 100 MHz
typ. >135 dB
®
of R&S ZVA24
100 MHz to 13 GHz
typ. >145 dB
13 GHz to 20 GHz
typ. >140 dB
20 GHz to 24 GHz
typ. >130 dB
from PORT 1 to MEAS 2 IN
Dynamic range at optional meas input
(option direct generator/receiver access)
10 MHz to 100 MHz
typ. >140 dB
®
of R&S ZVA40
100 MHz to 20 GHz
typ. >150 dB
20 GHz to 24 GHz
typ. >140 dB
24 GHz to 32 GHz
typ. >130 dB
32 GHz to 40 GHz
typ. >120 dB
The dynamic range is defined as the difference between the maximum source power and the rms value of the data trace of the
transmission magnitude produced by noise and crosstalk with test ports short-circuited. The specification is valid without system error
correction and at 10 Hz measurement bandwidth. The dynamic range can be increased by using a measurement bandwidth of 1 Hz.
Version 02.02, September 2006
®
Vector Network Analyzers R&S ZVA
3
Diagram: Dynamic range in dB vs. frequency in GHz of R&S®ZVA8
Diagram: Dynamic range in dB vs. frequency in GHz of R&S®ZVA24
Diagram: Dynamic range in dB vs. frequency in GHz of R&S®ZVA40
4
®
Vector Network Analyzers R&S ZVA
Version 02.02, September 2006
Measurement speed
Measurement time
Measurement time per point
Data transfer time
Time for measurement and data transfer
Switching time between channels
Switching time between two preloaded
instrument settings
for 201 measurements points, with span
100 MHz, 500 kHz measurement
bandwidth, ALC and display switched off
with center frequency 1.1 GHz
with center frequency 5.1 GHz
CW mode, 1 MHz measurement bandwidth
for 201 measurements points
via IEC BUS
via VX11 over 100 Mbit/s LAN
via RSIB over 100 Mbit/s LAN
for 201 measurements points, with start
frequency 1 GHz, stop frequency 1.1 GHz,
500 kHz measurement bandwidth, and
display switched off
(No additional time for data transfer is
needed, as it is done simultaneously during
the measurement.)
with not more than 2001 points
<2.9 ms
<1.3 ms
<0.7 ms
<6 ms
with not more than 2001 points
<10 ms
<6 ms
<4.5 ms
<3.5 µs
<1 ms
Table: Sweep times of R&S®ZVA
Number of measurement points
51
101
201
401
801
1601
Start frequency 5 GHz, stop frequency 5.2 GHz, ALC off, and measurement bandwidth of 100 kHz
with Full One Port calibration or
2.4 ms
3.9 ms
6.3 ms
11 ms
20.4 ms
40.2 ms
4.7 ms
8.6 ms
16.4 ms
32.4 ms
65 ms
170 ms
with correction switched off
with TOSM calibration
Start frequency 6 GHz, stop frequency 8 GHz, ALC off, and measurement bandwidth of 100 kHz
with Full One Port calibration or
3.4 ms
6.2 ms
11 ms
17.3 ms
28.2 ms
49 ms
5.3 ms
9.8 ms
18 ms
33 ms
63 ms
160 ms
with correction switched off
with TOSM calibration
Start frequency 10 MHz, stop frequency 8 GHz (ZVA8) or 24 GHz (ZVA24), ALC off, and measurement bandwidth of 100 kHz
with Full One Port calibration or
8.4 ms
12.6 ms
19.5 ms
30.5 ms
53.2 ms
88.2 ms
10.3 ms
16.6 ms
28 ms
47 ms
81 ms
190 ms
with correction switched off
with TOSM calibration
Version 02.02, September 2006
®
Vector Network Analyzers R&S ZVA
5
Measurement accuracy
This data is valid between 18 °C and 28 °C, provided the temperature has not varied by more than 1 K after calibration. Validity of the data
is conditional on the use of a suitable calibration kit by which the effective system data specified below is achieved. Frequency points,
measurement bandwidth, and sweep time have to be identical for measurement and calibration (no interpolation allowed).
Accuracy of transmission measurements
®
R&S ZVA8
300 kHz to 50 MHz
for +15 dB to –30 dB
for –30 dB to –45 dB
50 MHz to 8 GHz
for +15 dB to +5 dB
for +5 dB to –55 dB
for –55 dB to –70 dB
for –70 dB to –85 dB
<0.2 dB or <2°
<1 dB or <6°
<0.2 dB or <2°
<0.1 dB or <1°
<0.2 dB or <2°
<1 dB or <6°
®
R&S ZVA24
10 MHz to 50 MHz
50 MHz to 400 MHz
for +15 dB to –30 dB
for +15 dB to –30 dB
for –30 dB to –45 dB
for +15 dB to +5 dB
for +5 dB to –35 dB
for –35 dB to –50 dB
for –50 dB to –65 dB
for +15 dB to +5 dB
for +5 dB to –55 dB
for –55 dB to –70 dB
for –70 dB to –85 dB
400 MHz to 700 MHz
700 MHz to 24 GHz
<1 dB or <6°
<0.2 dB or <2°
<1 dB or <6°
<0.2 dB or <2°
<0.1 dB or <1°
<0.2 dB or <2°
<1 dB or <6°
<0.2 dB or <2°
<0.1 dB or <1°
<0.2 dB or <2°
<1 dB or <6°
®
R&S ZVA40
10 MHz to 50 MHz
50 MHz to 250 MHz
for +15 dB to –30 dB
<1 dB or <6°
for +15 dB to –30 dB
<0.2 dB or <2°
for –30 dB to –45 dB
<1 dB or <6°
250 MHz to 2 GHz
for +15 dB to +5 dB
<0.3 dB or <3°
for +5 dB to –50 dB
<0.1 dB or <1°
for –50 dB to –65 dB
<0.2 dB or <2°
for –65 dB to –80 dB
<1 dB or <6°
2 GHz to 24 GHz
for +15 dB to +5 dB
<0.3 dB or <3°
for +5 dB to –55 dB
<0.1 dB or <1°
for –55 dB to –70 dB
<0.2 dB or <2°
for –70 dB to –85 dB
<1 dB or <6°
24 GHz to 32 GHz
for +15 dB to +5 dB
<0.3 dB or <3°
for +5 dB to –45 dB
<0.2 dB or <2°
for –45 dB to –60 dB
<0.3 dB or <3°
for –60 dB to –75 dB
<1 dB or <6°
32 GHz to 40 GHz
for +15 dB to +5 dB
<0.4 dB or <4°
for +5 dB to –40 dB
<0.2 dB or <2°
for –40 dB to –55 dB
<0.4 dB or <4°
for –55 dB to –70 dB
<1 dB or <6°
Specifications are based on a matched DUT, a measurement bandwidth of 10 Hz, and a nominal source power of –10 dBm.
6
®
Vector Network Analyzers R&S ZVA
Version 02.02, September 2006
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA8
in the frequency range 300 kHz to 4 GHz
Magnitude
Phase
1
0.1
0.01
0
100
Uncertainty / deg
Uncertainty / dB
10
-20
-40
-60
-80
10
1
0.1
0
-100
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
Transm ission Coefficient / dB
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA8
in the frequency range 4 GHz to 8 GHz
Magnitude
Phase
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
1
0.1
0.01
0
10
-20
-40
-60
-80
Transmission Coefficient / dB
Version 02.02, September 2006
-100
0
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
®
Vector Network Analyzers R&S ZVA
7
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA24
in the frequency range 10 MHz to 700 MHz
Magnitude
Phase
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
10
1
0.1
0.01
0
-20
-40
-60
-80
0
-100
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
Transm ission Coefficient / dB
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA24
in the frequency range 700 MHz to 24 GHz
Magnitude
Phase
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
10
1
0.1
0.01
0
-20
-40
-60
-80
Transm ission Coefficient / dB
8
®
Vector Network Analyzers R&S ZVA
-100
0
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
Version 02.02, September 2006
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA40
in the frequency range 10 MHz to 700 MHz
Phase
Magnitude
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
10
1
0.1
0.01
0
-20
-40
-60
-80
0
-100
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
Transm ission Coefficient / dB
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA40
in the frequency range 700 MHz to 24 GHz
Magnitude
Phase
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
10
1
0.1
0.01
0
-20
-40
-60
-80
0
-100
-20
-40
-60
-80
-100
Transm ission Coefficient / dB
Transm ission Coefficient / dB
Diagram: Typical accuracy of transmission magnitude and transmission phase measurements of R&S®ZVA40
in the frequency range 24 GHz to 40 GHz
Phase
Magnitude
100
Uncertainty / deg
Uncertainty / dB
10
1
0.1
10
1
0.1
0.01
0
-20
-40
-60
-80
Transmission Coefficient / dB
Version 02.02, September 2006
-100
0
-20
-40
-60
-80
-100
Transmission Coefficient / dB
®
Vector Network Analyzers R&S ZVA
9
Accuracy of reflection measurements
®
R&S ZVA8
300 kHz to 8 GHz
for +10 dB to +3 dB
for +3 dB to –15 dB
for –15 dB to –25 dB
for –25 dB to –35 dB
<0.6 dB or <4°
<0.4 dB or <3°
<1 dB or <6°
<3 dB or <20°
for +3 dB to –15 dB
for –15 dB to –25 dB
for +10 dB to +3 dB
for +3 dB to –15 dB
for –15 dB to –25 dB
for –25 dB to –35 dB
<1 dB or <6°
<3 dB or <20°
<0.6 dB or <4°
<0.4 dB or <3°
<1 dB or <6°
<3 dB or <20°
®
R&S ZVA24
10 MHz to 50 MHz
50 MHz to 24 GHz
®
R&S ZVA40
10 MHz to 50 MHz
for +3 dB to –15 dB
<1 dB or <6°
for –15 dB to –25 dB
<3 dB or <20°
50 MHz to 40 GHz
for +10 dB to +3 dB
<0.6 dB or <4°
for +3 dB to –15 dB
<0.4 dB or <3°
for –15 dB to –25 dB
<1 dB or <6°
for –25 dB to –35 dB
<3 dB or <20°
Specifications are based on an isolating DUT, a measurement bandwidth of 10 Hz, and a nominal source power of –10 dBm.
Diagram: Typical accuracy of reflection magnitude and reflection phase measurements
of R&S®ZVA8 in the frequency range 300 kHz to 8 GHz,
of R&S®ZVA24 in the frequency range 50 MHz to 24 GHz,
and of R&S®ZVA40 in the frequency range 50 MHz to 40 GHz
Phase
10
0.05
Uncertainty / deg
Uncertainty (linear)
Magnitude
0.04
0.03
0.02
0.01
0.00
8
6
4
2
0
0
0.2
0.4
0.6
0.8
1
0
Reflection Coefficient (linear)
0.2
0.4
0.6
0.8
1
Reflection Coefficient (linear)
Trace stability
at 0 dBm source power and 0 dB reflection
and 1 kHz measurement bandwidth
Trace noise of S11 (rms)
®
R&S ZVA8
300 kHz to 8 GHz
®
R&S ZVA24
700 MHz to 24 GHz
®
R&S ZVA40
700 MHz to 24 GHz
24 GHz to 40 GHz
Temperature dependence
10
<0.004 dB, typ. 0.001 dB
<0.004 dB, typ. 0.001 dB
at 0 dB transmission or reflection
®
Vector Network Analyzers R&S ZVA
<0.004 dB, typ. 0.001 dB
<0.015 dB, typ. 0.004 dB
<0.05 dB/K or <0.4°/K
Version 02.02, September 2006
Effective system data
This data is valid between 18 °C and 28 °C, provided the temperature has not varied by more than 1 K after calibration. The data is based
on a measurement bandwidth of 10 Hz and system error calibration by means of a suitable calibration kit. Frequency points, measurement
bandwidth, and sweep time have to be identical for measurement and calibration (no interpolation allowed).
®
R&S ZVA8
Directivity
Source match
Reflection tracking
Load match
Transmission tracking
300 kHz to 4 GHz
4 GHz to 8 GHz
300 kHz to 4 GHz
4 GHz to 8 GHz
300 kHz to 4 GHz
4 GHz to 8 GHz
300 kHz to 4 GHz
4 GHz to 8 GHz
300 kHz to 4 GHz
4 GHz to 8 GHz
>46 dB, typ. 50 dB
>40 dB, typ. 50 dB
>40 dB, typ. 46 dB
>36 dB, typ. 40 dB
<0.04 dB, typ. 0.01 dB
<0.1 dB, typ. 0.01 dB
>46 dB, typ. 50 dB
>40 dB, typ. 46 dB
<0.06 dB, typ. 0.01 dB
<0.2 dB, typ. 0.05 dB
10 MHz to 700 MHz
700 MHz to 24 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
>36 dB, typ. 40 dB
>40 dB, typ. 50 dB
>30 dB, typ. 48 dB
>30 dB, typ. 48 dB
<0.3 dB, typ. 0.05 dB
<0.3 dB, typ. 0.05 dB
>36 dB, typ. 40 dB
>40 dB, typ. 50 dB
<0.3 dB, typ. 0.1 dB
<0.3 dB, typ. 0.1 dB
10 MHz to 700 MHz
700 MHz to 24 GHz
24 GHz to 40 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
24 GHz to 40 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
24 GHz to 40 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
24 GHz to 40 GHz
10 MHz to 700 MHz
700 MHz to 24 GHz
24 GHz to 40 GHz
>30 dB, typ. 40 dB
>36 dB, typ. 46 dB
>30 dB, typ. 40 dB
>30 dB, typ. 36 dB
>30 dB, typ. 40 dB
>30 dB, typ. 36 dB
<0.3 dB, typ. 0.1 dB
<0.3 dB, typ. 0.1 dB
<0.3 dB, typ. 0.2 dB
>32 dB, typ. 40 dB
>36 dB, typ. 46 dB
>32 dB, typ. 40 dB
<0.3 dB, typ. 0.2 dB
<0.3 dB, typ. 0.1 dB
<0.3 dB, typ. 0.2 dB
®
R&S ZVA24
Directivity
Source match
Reflection tracking
Load match
Transmission tracking
®
R&S ZVA40
Directivity
Source match
Reflection tracking
Load match
Transmission tracking
Version 02.02, September 2006
®
Vector Network Analyzers R&S ZVA
11
Test port output
®
R&S ZVA8
300 kHz to 50 MHz
50 MHz to 4 GHz
4 GHz to 7 GHz
7 GHz to 8 GHz
®
R&S ZVA24
10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40
10 MHz to 50 MHz
50 MHz to 20 GHz
20 GHz to 32 GHz
32 GHz to 40 GHz
®
R&S ZVA8
at –10 dBm
in temperature range 18 °C to 28 °C
50 MHz to 8 GHz
®
R&S ZVA24
at –10 dBm
in temperature range 18 °C to 28 °C
500 MHz to 24 GHz
®
R&S ZVA40
at –10 dBm
in temperature range 18 °C to 28 °C
500 MHz to 24 GHz
24 GHz to 40 GHz
Power range
(without optional step attenuators
and without optional direct
generator/receiver access)
Power accuracy
(with ALC on and
without power calibration)
Power linearity
referenced to –10 dBm
above 50 MHz
in temperature range 18 °C to 28 °C
(with ALC on and without power cal.)
®
R&S ZVA8 above 50 MHz
®
R&S ZVA24 above 500 MHz
®
R&S ZVA40 above 500 MHz
Power resolution
Harmonics
(Output power is referenced to maximum
specified output power)
12
®
®
R&S ZVA8
300 kHz to 50 MHz at –3 dB
50 MHz to 4 GHz at –5 dB
4 GHz to 7 GHz at –2 dB
7 GHz to 8 GHz at 0 dB
®
R&S ZVA24
10 MHz to 50 MHz at –3 dB
50 MHz to 13 GHz at –3 dB
13 GHz to 24 GHz at 0 dB
®
R&S ZVA40
10 MHz to 50 MHz at –3 dB
50 MHz to 20 GHz at –3 dB
20 GHz to 32 GHz at 0 dB
32 GHz to 40 GHz at 0 dB
Vector Network Analyzers R&S ZVA
–40 dBm to +10 dBm, typ. –45 to +14 dBm
–40 dBm to +13 dBm, typ. –45 to +15 dBm
–40 dBm to +10 dBm, typ. –45 to +13 dBm
–40 dBm to +8 dBm, typ. –45 to +12 dBm
–30 dBm to +13 dBm, typ. –40 to +18 dBm
–30 dBm to +10 dBm, typ. –40 to +16 dBm
–30 dBm to +10 dBm, typ. –40 to +15 dBm
–30 dBm to +13 dBm, typ. –40 to +18 dBm
–30 dBm to +10 dBm, typ. –40 to +15 dBm
–30 dBm to +6 dBm, typ. –40 to +12 dBm
<2 dB
<0.8 dB, typ. 0.3 dB
<3 dB
<0.8 dB, typ. 0.3 dB
<3 dB
<0.8 dB, typ. 0.3 dB
<2 dB, typ. 0.8 dB
<2 dB
<0.8 dB, typ. 0.3 dB
<0.8 dB, typ. 0.3 dB
<0.8 dB, typ. 0.3 dB
0.01 dB
typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
<–20 dBc, typ. <–30 dBc
Version 02.02, September 2006
Diagram: Maximum output power in dBm vs. frequency in GHz of R&S®ZVA8
Diagram: Maximum output power in dBm vs. frequency in GHz of R&S®ZVA24
Diagram: Maximum output power in dBm vs. frequency in GHz of R&S®ZVA40
Version 02.02, September 2006
®
Vector Network Analyzers R&S ZVA
13
Diagram: Output power accuracy in dB vs. frequency in GHz of R&S®ZVA8
Diagram: Output power accuracy in dB vs. frequency in GHz of R&S®ZVA24
Diagram: Output power accuracy in dB vs. frequency in GHz of R&S®ZVA40
14
®
Vector Network Analyzers R&S ZVA
Version 02.02, September 2006
Test port input
Match
Maximum nominal input level
Power measurement accuracy
Receiver linearity
Damage level
Damage DC voltage
Noise level
(without optional step attenuators
and without optional direct
generator/receiver access)
Version 02.02, September 2006
without system error correction
®
R&S ZVA8 300 kHz to 7 GHz
7 GHz to 8 GHz
®
R&S ZVA24 10 MHz to 50 MHz
50 MHz to 2 GHz
2 GHz to 24 GHz
®
R&S ZVA40 10 MHz to 4 GHz
4 GHz to 24 GHz
24 GHz to 40 GHz
®
R&S ZVA8 300 kHz to 8 GHz
®
R&S ZVA24 10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40 10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
at –10 dBm without power calibration
in temperature range 18 °C to 28 °C
®
R&S ZVA8 10 MHz to 8 GHz
®
R&S ZVA24 10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40 10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
referenced to –10 dBm
in temperature range 18 °C to 28 °C
®
R&S ZVA8
for +20 dB to –60 dB
50 MHz to 8 GHz
®
R&S ZVA24
for +20 dB to –30 dB
50 MHz to 700 MHz
for +20 dB to +10 dB
700 MHz to 24 GHz
for +10 dB to –45 dB
700 MHz to 24 GHz
®
R&S ZVA40
for +20 dB to –30 dB
50 MHz to 250 MHz
for +15 dB to +10 dB
250 MHz to 40 GHz
for +10 dB to –45 dB
250 MHz to 40 GHz
>16 dB
>14 dB
>10 dB
>12 dB
>8 dB
>12 dB
>8 dB
>6 dB
+13 dBm
+15 dBm
+10 dBm
+10 dBm
+6 dBm
+3 dBm
1 dB
1 dB
2 dB
1 dB
2 dB
3 dB
0.1 dB
0.1 dB
0.3 dB
0.1 dB
0.1 dB
0.3 dB
0.1 dB
+27 dBm
30 V
at 10 Hz measurement bandwidth
®
R&S ZVA8
300 kHz to 100 MHz
100 MHz to 8 GHz
®
R&S ZVA24
100 MHz to 700 MHz
700 MHz to 2 GHz
2 GHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40
100 MHz to 500 MHz
500 MHz to 2 GHz
2 GHz to 20 GHz
20 GHz to 24 GHz
24 GHz to 32 GHz
32 GHz to 40 GHz
<–100 dBm
<–115 dBm
<–80 dBm
<–110 dBm
<–115 dBm
<–110 dBm
<–80 dBm
<–110 dBm
<–115 dBm
<–110 dBm
<–100 dBm
<–95 dBm
®
Vector Network Analyzers R&S ZVA
15
Noise level at optional meas input
(option direct generator/receiver access)
at 10 Hz measurement bandwidth
®
R&S ZVA8
100 MHz to 8 GHz
®
R&S ZVA24
100 MHz to 24 GHz
®
R&S ZVA40
100 MHz to 24 GHz
24 GHz to 40 GHz
The noise level is defined as the rms value of the indicated noise floor.
16
®
Vector Network Analyzers R&S ZVA
typ. <–130 dBm
typ. <–130 dBm
typ. <–130 dBm
typ. <–120 dBm
Version 02.02, September 2006
Additional front panel connectors
USB
(two) Universal Serial Bus connectors for connecting USB devices (USB 1.1);
two additional USB connectors at the rear panel
Optional front panel connectors
SOURCE OUT
SOURCE IN
REF OUT
REF IN
MEAS OUT
MEAS IN
output of internal source signal (SMA female)
input for external source signal (SMA female)
output of internal reference signal (SMA female)
input for external reference signal (SMA female)
output of internal measurement signal (SMA female)
input for external measurement signal (SMA female)
Display
Screen
Resolution
Version 02.02, September 2006
26 cm (10.4") diagonal colour LCD
800 × 600 × 262144 (high colour)
®
Vector Network Analyzers R&S ZVA
17
Rear panel connectors
IEC BUS
remote control according to IEEE488, IEC60625; 24 pins
LAN 1
first Local Area Network connector, 8 pins, RJ-45
LAN 2
second Local Area Network connector, 8 pins, RJ-45
USB
(two) Universal Serial Bus connectors for connecting USB devices (USB 1.1);
two additional USB connectors at the front panel
10 MHz REF
altenatively input or output for external frequency reference signal
Connector type
Input frequency
Maximum allowed deviation
Input power
Input impedance
Output frequency
Output frequency accuracy
Output power
BNC, female
10 MHz
1 kHz
–3 dBm ± 8 dB
50 Ω
10 MHz
80 Hz
–3 dBm ± 8 dB at 50 Ω
DC measurement input
DC MEAS 1 V
Connector type
Voltage range
Measurement accuracy
Input impedance
Damage voltage
4-pin Mini DIN, female
–1 V to +1 V
2.5 % of reading + 2.5 mV
>10 kΩ
30 V
DC measurement input
DC MEAS 10 V
Connector type
Voltage range
Measurement accuracy
Input impedance
Damage voltage
4-pin Mini DIN, female
–10 V to +10 V
2.5 % of reading + 25 mV
>10 kΩ
30 V
DC bias input for PORT
PORT BIAS
Connector type
Maximum nominal input voltage
Maximum nominal input current
Damage voltage
Damage current
18
BNC, female
30 V
200 mA
30 V
500 mA
®
Vector Network Analyzers R&S ZVA
Version 02.02, September 2006
MONITOR
IBM-PC-compatible VGA monitor connector, 15-pin Sub-D (for external monitor)
USER CONTROL
FOOT SWITCH 1 and FOOT SWITCH 2
DRIVE PORT 1 to DRIVE PORT 4
CHANNEL BIT 0 to CHANNEL BIT 3
PASS 1 and PASS 2
BUSY
READY FOR TRIGGER
EXT GEN TRIGGER
EXT GEN BLANK
EXTERNAL TRIGGER
several control and trigger signals, 25-pin Sub-D, 3.3 V TTL
for controlling external generators, for limit checks, sweep signals, etc.
pin 24 and pin 25 (inputs)
control inputs
pin 16 to pin 19 (outputs)
indicate driving port
pin 8 to pin 11 (outputs)
channel-specific user-configurable bits
pin 13 and pin 14 (outputs)
pass/fail results of limit checks
pin 4 (output)
measurements running
pin 6 (output)
ready for trigger
pin 21 (output)
control signal for external generator
pin 22 (input)
handshake signal from external generator
pin 2 (input)
trigger input for analyzer
EXT TRIGGER
trigger input for analyzer
Connector type
TTL-signal (edge triggerd)
Polarity (user-selectable)
Minimum pulse width
Input impedance
Version 02.02, September 2006
BNC, female
3V
positive or negative
1 µs
>10 kΩ
®
Vector Network Analyzers R&S ZVA
19
Options
Generator Step Attenuators
extend the lower limit of the output power range by 70 dB.
Frequency range
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA40
®
R&S ZVA8
300 kHz to 8 GHz
300 kHz to 8 GHz
®
R&S ZVA24
10 MHz to 13 GHz
13 GHz to 24 GHz
10 MHz to 24 GHz
®
R&S ZVA40
10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
10 MHz to 40 GHz
at –10 dBm without power calibration
®
Power range
Power accuracy
Power linearity
(with ALC off)
Dynamic range
above –70 dBm
from –70 dBm to –100 dBm
®
R&S ZVA8
300 kHz to 8 GHz
®
R&S ZVA24
10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40
10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
300 kHz to 8 GHz
10 MHz to 24 GHz
10 MHz to 40 GHz
upper limit is reduced by 1 dB
lower limit is extended by 70 dB
upper limit is reduced by 1 dB
upper limit is reduced by 2 dB
lower limit is extended by 70 dB
upper limit is reduced by 1 dB
upper limit is reduced by 2 dB
upper limit is reduced by 3 dB
lower limit is extended by 70 dB
identical to specifications
without optional step attenuators
<2 dB
<3 dB
is reduced by 1 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 3 dB
Receiver Step Attenuators
permit the level of the input signal to be attenuated in 5 dB steps up to 35 dB.
Frequency range
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA40
®
Attenuation
Attenuation steps
Attenuation accuracy
Dynamic range
®
R&S ZVA8
300 kHz to 8 GHz
®
R&S ZVA24
10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40
10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
®
R&S ZVA8
300 kHz to 8 GHz
®
R&S ZVA24
10 MHz to 13 GHz
13 GHz to 24 GHz
®
R&S ZVA40
10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
Noise level
20
300 kHz to 8 GHz
10 MHz to 24 GHz
10 MHz to 40 GHz
0 dB to 35 dB
5 dB
2 dB
®
Vector Network Analyzers R&S ZVA
is reduced by 1 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 3 dB
is reduced by 1 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 1 dB
is reduced by 2 dB
is reduced by 3 dB
Version 02.02, September 2006
Direct Generator/Receiver Access
Frequency range
Dynamic range
Power range
Noise level
These options permit the direct access to the internal source output as well as to the
internal reference and measurement receiver inputs via front panel connectors (SMA)
®
300 kHz to 8 GHz
R&S ZVA8
®
10 MHz to 24 GHz
R&S ZVA24
®
10 MHz to 40 GHz
R&S ZVA40
®
R&S ZVA8
is reduced by 2 dB
300 kHz to 8 GHz
®
R&S ZVA24
is reduced by 2 dB
10 MHz to 13 GHz
is reduced by 4 dB
13 GHz to 24 GHz
®
R&S ZVA40
is reduced by 2 dB
10 MHz to 13 GHz
is reduced by 4 dB
13 GHz to 24 GHz
24 GHz to 40 GHz
is reduced by 6 dB
®
R&S ZVA8
upper limit is reduced by 1 dB
300 kHz to 8 GHz
®
R&S ZVA24
upper limit is reduced by 1 dB
10 MHz to 13 GHz
upper limit is reduced by 2 dB
13 GHz to 24 GHz
®
R&S ZVA40
upper limit is reduced by 1 dB
10 MHz to 13 GHz
13 GHz to 24 GHz
upper limit is reduced by 2 dB
24 GHz to 40 GHz
upper limit is reduced by 3 dB
®
R&S ZVA8
is increased by 1 dB
300 kHz to 8 GHz
®
R&S ZVA24
is increased by 1 dB
10 MHz to 13 GHz
is increased by 2 dB
13 GHz to 24 GHz
®
R&S ZVA40
10 MHz to 13 GHz
13 GHz to 24 GHz
24 GHz to 40 GHz
Version 02.02, September 2006
is increased by 1 dB
is increased by 2 dB
is increased by 3 dB
®
Vector Network Analyzers R&S ZVA
21
General data
Temperature loading
specs complied with
operating temperature range
storage temperature range
Damp heat
Mechanical resistance
vibration, sinusoidal
vibration, random
shock
Calibration interval
EMC, RF emission
EMC, other emissions and immunity
Safety
Power supply
Power consumption
Test mark
Dimensions ( W × H × D )
Weight
22
®
Vector Network Analyzers R&S ZVA
5 °C to 40 °C
5 °C to 40 °C
–40 °C to 70 °C
meets IEC 60068-2-1 and IEC 60068-2-2
40 °C at 95 % rel. humidity,
meets IEC 60068-2-30
5 Hz to 150 Hz,
meets IEC 60068-2-6
10 Hz to 300 Hz,
meets IEC 60068-2-64
40 g shock spectrum,
meets IEC 60068-2-27, MIL-STD 810
1 year
meets CISPR 11/EN 55011 Group 1
Class A (for a shielded test set-up)
meets IEC/EN 61326,
emission class B (residential environment),
immunity industrial environment (excluding
operating frequency)
meets IEC 61010-1, EN61010-1, and
UL 3111-1
100 V to 240 V (AC) with tolerance ±10 %,
50 Hz to 60 Hz with tolerance ±5 %,
safety class I to VDE 411
450 W typ. 310 W (Standby: typ. 10 W)
VDE, GS, CSA, CSA-NRTL/C,
CE conformity mark
465.1 mm × 286.2 mm × 495.0 mm
25 kg
Version 02.02, September 2006
Ordering information
Designation
Type
Vector Network Analyzer, 8 GHz, 2 ports
Vector Network Analyzer, 8 GHz, 4 ports
Vector Network Analyzer, 24 GHz, 2 ports
Vector Network Analyzer, 24 GHz, 4 ports
Vector Network Analyzer, 40 GHz, 2 ports
Vector Network Analyzer, 40 GHz, 4 ports
Options
R&S ZVA8
®
R&S ZVA8
®
R&S ZVA24
®
R&S ZVA24
®
R&S ZVA40
®
R&S ZVA40
Order No.
®
1145.1110.08
1145.1110.10
1145.1110.24
1145.1110.26
1145.1110.40
1145.1110.42
®
1164.0209.08
®
1164.0209.10
®
1164.0209.24
®
1164.0209.26
®
1164.0209.40
®
1164.0209.42
®
1164.0009.02
®
1164.0109.02
®
1302.5409.02
®
1164.0015.02
®
1164.0115.02
®
1302.5415.02
®
1164.0021.02
®
1164.0121.02
®
1302.5421.02
®
1164.0038.02
®
1164.0138.02
®
1302.5438.02
®
1164.0044.02
®
1164.0144.02
®
1302.5444.02
®
1164.0050.02
®
1164.0150.02
®
1302.5450.02
®
1164.0067.02
®
1164.0167.02
®
1302.5467.02
®
1164.0073.02
®
1164.0173.02
®
1302.5473.02
®
1164.1757.02
®
1164.1657.02
®
1164.1863.02
Direct Generator/Receiver Access
®
R&S ZVA8-B16
®
R&S ZVA8-B16
for R&S ZVA8 with two ports
for R&S ZVA8 with four ports
®
R&S ZVA24-B16
®
R&S ZVA24-B16
for R&S ZVA24 with two ports
for R&S ZVA24 with four ports
®
R&S ZVA40-B16
®
R&S ZVA40-B16
for R&S ZVA40 with two ports
for R&S ZVA40 with four ports
Generator Step Attenuator Port 1
®
R&S ZVA8-B21
®
R&S ZVA24-B21
for R&S ZVA8
for R&S ZVA24
®
for R&S ZVA40
R&S ZVA40-B21
Generator Step Attenuator Port 2
®
for R&S ZVA8
R&S ZVA8-B22
®
R&S ZVA24-B22
®
R&S ZVA40-B22
for R&S ZVA24
for R&S ZVA40
Generator Step Attenuator Port 3
®
for R&S ZVA8 with four ports
R&S ZVA8-B23
®
R&S ZVA24-B23
®
R&S ZVA40-B23
for R&S ZVA24 with four ports
for R&S ZVA40 with four ports
Generator Step Attenuator Port 4
®
R&S ZVA8-B24
®
R&S ZVA24-B24
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
®
for R&S ZVA40 with four ports
R&S ZVA40-B24
Receiver Step Attenuator Port 1
®
R&S ZVA8-B31
®
R&S ZVA24-B31
for R&S ZVA8
for R&S ZVA24
®
for R&S ZVA40
R&S ZVA40-B31
Receiver Step Attenuator Port 2
®
for R&S ZVA8
R&S ZVA8-B32
®
R&S ZVA24-B32
®
R&S ZVA40-B32
for R&S ZVA24
for R&S ZVA40
Receiver Step Attenuator Port 3
®
for R&S ZVA8 with four ports
®
for R&S ZVA24 with four ports
®
for R&S ZVA40 with four ports
R&S ZVA8-B33
R&S ZVA24-B33
R&S ZVA40-B33
Receiver Step Attenuator Port 4
®
R&S ZVA8-B34
®
R&S ZVA24-B34
for R&S ZVA8 with four ports
for R&S ZVA24 with four ports
®
for R&S ZVA40 with four ports
Oven Quartz (OCXO)
Time Domain
Frequency Conversion
Version 02.02, September 2006
R&S ZVA40-B34
R&S ZVAB-B4
R&S ZVAB-K2
R&S ZVA-K4
®
Vector Network Analyzers R&S ZVA
23
Certified Environmental System
ISO 9001
ISO 14001
DQS REG. NO 1954 QM
DQS REG. NO 1954 UM
For product brochure, see PD 5213.5680.12
and www.rohde-schwarz.com
(search term: ZVA)
www.rohde-schwarz.com
Europe: +49 1805 12 4242, [email protected]
USA and Canada: +1-888-837-8772, [email protected]
Asia: +65 65 130 488, [email protected]
¸ is a registered trademark of Rohde & Schwarz GmbH & Co. KG · Trade names are trademarks of the owners · Printed in Germany (U xx)
PD 5213.5680.22 · ¸ZVA · Version 02.02 · September 2006 · Data without tolerance limits is not binding · Subject to change
Certified Quality System
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement