Honda BF130A User's Manual

HONDA
BFI 15A/BF130A
Owner’s Manual
0 2001 Honda Motor Co.,Ltd. -All Rights Reserved
2002
The engineexhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
Keep this owner’s manual handy, so you can refer to it at any time. This owner’s
manual is considered a permanent part of the outboard motor and should remain with
the outboard motor if resold.
The information and specifications included in this publication were in effect at the
time of approval for printing. Honda Motor Co., Ltd. reserves the right, however, to
discontinue or change specifications or design at any time without notice and without
incurring any obligation whatever. No part of this publication may be reproduced
without written permission.
INTRODUCTION
Congratulations on your selection of
a Hondaoutboard motor. We are
certain you will be pleased with your
purchase of one of the finest
outboard motors on the market.
We want to help you get the best
results from your new outboard
motor and tooperate it safely. This
manual contains the information on
how to do that; please read it
carefully.
As you read this manual you will
find information preceded by a
p
q
i
symbol. That information is intended
to helpyou avoid damage toyour
outboard motor, other property, or
the environment.
We suggest you read the warranty
policy to fully understand its
coverage and your responsibilities of
ownership. The warranty policy is a
separate document that should have
been given to you by your dealer.
When your outboard motor needs
scheduled maintenance, keep in mind
that your Honda marine dealer is
specially trained in servicing Honda
outboard motors. Your Honda marine
dealer isdedicated to your
satisfaction and will be pleased to
answer your questions and concerns.
02001 Honda Motor Co., Ltd. All
Rights Reserved
1
INTRODUCTION
A FEW WORDS ABOUT
SAFETY
Your safety and the safetyof others
are very important, And using this
outboard motor safely is an important
responsibility.
You will find important safety information in a variety of forms, including:
Safety Labels - on the outboard motor.
A
Safety Messages - preceded by a safety alert symbol
and one of
three signal words, DANGER, WARNING, or CAUTION.
These signal words mean:
To help you make informed
decisions about safety, we have
provided operating procedures and
other information on labels and in
this manual. This information alerts
you to potential hazard that could
hurt you or others.
Of course, it is not practical or
possible towarn you about all the
hazards associated with operating or
maintaining an outboard motor. You
must use your own good judgment.
You WILL be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY
HURT if you don’t follow instructions.
You CAN be HURTif you don’t follow
instructions.
Safety Headings - such as IMPORTANT SAFETY INFORMATION.
Safety Section - such as OUTBOARD MOTOR SAFETY.
Instructions - how to use this outboard motor correctly and safely.
This entire book is filledwith important safety information - please read it
carefully.
2
CONTENTS
OUTBOARD MOTOR SAFETY.................................... 7
IMPORTANT SAFETY INFORMATION
................. 7
SAFETY LABEL LOCATIONS.................................
9
CONTROLS AND FEATURES ...................................
10
CONTROL AND FEATURE IDENTIFICATION
CODES ................................................................... 10
COMPONENT AND CONTROL LOCATIONS..... 11
CONTROLS...............................................................
15
Side-Mount Type
Ignition Switch.......................................................
15
Switch Clipand Emergency Stop Switch.............. 16
GearshifdThrottle Control Lever
...........................
16
Fast Idle Lever........................................................ 18
Panel-Mount Type
Ignition Switch.......................................................
18
Switch Clipand Emergency Stop Switch.............. 19
Throttle Button ....................................................... 20
GearshifdThrottle Control Lever
........................... 20
Top-Mount Type
Ignition Switch....................................................... 22
Switch Clipand Emergency Stop Switch.............. 22
Throttle Button ....................................................... 23
........................... 23
GearshifVThrottle Control Lever
Common Controls
25
Power TridTilt Switch .........................................
Power Tilt Switch...................................................
26
Manual Relief Valve .............................................. 26
Tilt LockLever ...................................................... 26
Engine Cover Lock Levers....................................
27
Transom Angle Adjusting Rod .............................. 27
Trim Tab.................................................................
28
28
INSTRUMENTS........................................................
Trim Meter (optional equipment)
.......................... 28
Tachometer (optional equipment)
.......................... 28
Fuel Gauge (optional equipment).......................... 29
3
CONTENTS
INDICATORS............................................................ 29
.................................... 29
Alternator (AGC) Indicator
Programmed Fuel Injection (PGM-FI) Indicator... 29
30
Oil Pressure Indicator.............................................
Overheating Indicator ............................................
30
31
Cooling System Indicator......................................
OTHER FEATURES................................................. 3 1
Overrev Limiter...................................................... 3 1
Anodes ....................................................................
32
Portable Fuel Tank (optional equipment).............. 32
Fuel Cap Vent Knob (optional equipment)........... 32
33
Fuel Priming Bulb..................................................
BEFORE OPERATION.................................................
34
ARE YOU READY TO GET UNDER WAY ? ...... 34
IS YOUR OUTBOARD MOTOR
READY TO GO? .................................................
34
4
36
OPERATION .................................................................
36
SAFE OPERATING PRECAUTIONS.....................
BREAK-IN PROCEDURE........................................ 36
TRANSOM ANGLE ADJUSTMENT...................... 37
PORTABLE FUEL TANK (optional equipment)
..... 38
FUEL HOSE CONNECTIONS
................................. 38
FUEL PRIMING........................................................ 39
39
STARTING THE ENGINE.......................................
Side-Mount Type................................................... 39
Panel-Mount Type.................................................. 42
Top-Mount Type.................................................... 44
STOPPING THE ENGINE
........................................ 46
46
Emergency Engine Stopping.................................
Normal Engine Stopping........................................ 47
GEARSHIFTING AND
THROTTLE OPERATION............................... 48
Side-Mount Type................................................... 48
49
Panel-Mount Type..................................................
Top-Mount Type.................................................... 49
STEERING ................................................................ 50
CRUISING .................................................................
51
SHALLOW WATER OPERATION
......................... 53
................ 53
MOORING. BEACHING. LAUNCHING
CONTENTS
SERVICING YOUR OUTBOARD MOTOR
............... 55
THE IMPORTANCEOF MAINTENANCE ............ 55
MAINTENANCE SAFETY...................................... 56
TOOL KIT(optional equipment)............................... 57
MAINTENANCE SCHEDULE................................
58
TRIM TAB ADJUSTMENT..................................... 60
MANUAL RELIEF VALVE..................................... 61
ENGINE COVER REMOVAL AND
INSTALLATION...................................................
61
Look Lever Adjustment............................................. 62
................................ 62
Look Lever Bracket Adjustment
Engine Oil Level Check.............................................
63
Engine Oil Change ..................................................... 63
Oil Filter Change ........................................................ 64
66
Engine Oil Recommendations ...................................
67
Gear Oil Level Check.................................................
Lubrication Points ...................................................... 68
Spark PlugService ..................................................... 69
REFUELING .............................................................. 71
FUEL RECOMMENDATIONS................................ 72
Fuel PumpFilter Inspection and Replacement.......... 73
Portable Fuel Tank and
Filter Cleaning (optional equipment) ..................... 75
Anode Replacement...................................................
76
77
Propeller Replacement ...............................................
STORAGE .....................................................................
78
STRAGE PREPARATION....................................... 78
78
Cleaning and Flushing...........................................
Fuel ......................................................................... 80
Engine Oil .............................................................. 81
HOISTING THE OUTBOARDMOTOR ................. 81
82
STORAGE PRECAUTIONS....................................
83
REMOVAL FROM STRAGE...................................
CONTENTS
TRANSPORTING .........................................................
WITH OUTBOARD MOTOR
INSTALLED ON BOAT .......................................
WITH OUTBOARD MOTOR
REMOVED FROM BOAT...................................
84
INDEX..........................................................................
84
WIRING DIAGRAMS.........................
84
..... 85
TAKING CARE OF UNEXPECTED PROBLEMS
BATTERY WILL NOT CHARGE AND
ELECTRIC STARTER WILL NOT
OPERATE..........................................................
90
OFF
OIL PRESSURE INDICATOR LIGHT GOES
AND ENGINE SPEED IS LIMITED
.................... 92
OVERHEATING INDICATOR LIGHT COMES
ON AND ENGINE SPEEDIS LIMITED............. 93
SUBMERGED MOTOR ........................................... 94
TECHNICAL AND CONSUMER INFORMATION... 96
TECHNICAL INFORMATION................................ 96
96
Serial Number Locations.......................................
Oxygenated Fuels................................................... 97
Emission Control System Information.................. 98
Star Label .............................................................
100
Specifications.......................................................
102
CONSUMER INFORMATION..............................
105
6
106
Inside Back Cover
OUTBOARD MOTOR SAFETY
IMPORTANT SAFETY
INFORMATION
Operator Responsibility
0
Honda BFllSA/BF130A outboard
motors are designed for use with
boats that have asuitable
manufacturer’s power
recommendation. Other uses can
result in injury to the operator or
damage to the outboard motor and
other property.
Most accidents can be prevented if
you follow all instructions in this
manual and on the outboard motor.
The most common hazards are
discussed below, along with the best
way to protect yourself and others.
0
0
It is the operator’s responsibility to
provide the necessary safeguards
to protect people and property.
Know how to stop the engine
quickly in case of emergency.
Understand the use of all controls.
Stop the engine immediately if
anyone falls overboard, and do not
run the enginewhile the boat is
near anyone in the water.
Always stop the engine if you
must leave the controls for any
reason.
0
0
0
0
0
0
Attach the emergency stop switch
lanyard securely to the operator.
Always wear a PFD (Personal
Flotation Device) while on the
boat.
Familiarize yourself with all laws
and regulations relating to boating
and the use of outboard motors.
Be surethat anyone whooperates
the outboard motor receives proper
instruction.
Be sure the outboard motor is
properly mounted on the boat.
Do not remove the engine cover
while the engineis running.
7
OUTBOARD MOTOR SAFETY
Refuel With Care
Gasoline is extremely flammable,
and gasoline vapor can explode.
Refuel outdoors, in a wellventilated area, with the engine
stopped. Never smoke near
gasoline, and keep other flames
and sparks away.
Remove any portable fuel tank
from the boat for refueling. Keep
the portable fueltank away from
the battery or other potential spark
sources.
Refuel carefully to avoid spilling
fuel. Avoid overfilling the fuel
tank.
After refueling, tighten the filler
cap securely. If any fuel is spilled,
make sure the area is dry before
starting the engine.
8
Carbon Monoxide Hazard
Exhaust gas contains poisonous
carbon monoxide. Avoid inhalation
of exhaust gas. Never run the engine
in a closed garage or confined area.
OUTBOARD MOTOR SAFETY
SAFETY LABEL LOCATIONS
OPTIONAL
FUEL TANK
A
WARNING
FLAMMABLE DANGEROUS
I B E S U R EI H EA N T I V E N T l L A I l O NP L A T E
I S BELOW
THE
WATER L I N E
I D 0 NOT S U l F I I O REVERSESUDDENLYATHIGH
SPEED
I C H E C KO I LL E V E LB E F O R ES T A R T I N G .
I F L U S H THESYSTEMTHOROUGHLYWITHFRESHWATER
AFTEREACHUSEINSALT
WATER
IEYERGENCYSTARTINGINSTRUCTIONSAREON
ENG I N €
G A S O L I N E
REMOVE
FROM
BOAT FOR FILLING
INFLAMMABLE DANGEREUX
IOP OF
G A Z O L I N E
SOBTlR OU BATEAUPOUR
REFAIRE LE PLEINQESSENCE
The labels shown here contain important safety information. Please read them carefully. These labels are considered
permanent parts of your outboard motor. If a label comes off orbecomes hard to read, contact an authorized Honda
Marine servicing dealer for a replacement.
9
CONTROLS AND FEATURES
CONTROL AND FEATURE IDENTIFICATION CODES
1
I
Model
I
BFl15A
LCA XA LA
XCA
Type
L
e
XA LA
e
0
I
BF130A
LCA
XCA
0
Shaft Length
Standard Rotating Propeller Shaft
~~~~
~~
e
e
X
e
e
e
e
e
~
~
~~~~~~
Counterrotating Propeller Shaft
e
e
e
e
Power TridTilt
e
e
0
e
e
e
e
0
Trimeter
e
0
e
e
e
e
e
e
Refer to this chart for an explanation of theType Codes used inthis manual to identify control andfeature applications.
TYPECODE (example)
L C A
T T T
10
e
Destination
A America
Rotating direction of propellershaft
C: Counterrotating propeller shaft
None: Standard rotating propeller shaft
Shaft length
L: Long Shaft
X: Extra Long Shaft
CONTROLS AND FEATURES
COMPONENT AND CONTROL LOCATIONS
ENGINE COVER
OIL LEVEL DIPSTICK
\
POWER TILT SWITCH
ENGINE COVER
LOCK LEVER
OIL FILLER CAP
/
FUEL HOSE
CONNECTOR
ENGINE OIL
DRAIN PLUG-.
WASH PLUG
MANUAL RELI
ENGINE COVER
LOCK LEVER
DRAIN PLUG
COVER
ANTIVENTILATION
ANODE
SYSTEM
INDICATOR
XHAUST PORT
TRIM T
INSPECTION
DRAIN BOLT
WATER
INTAKE
11
CONTROLS AND FEATURES
Remote Controls (optional equipment)
(SIDE-MOUNT REMOTE CONTROL)
GEARSHIFTmHROTTLE
CONTROL LEVER
\
(PANEL-MOUNT REMOTE CONTROL)
NEUTRAL
RELEASE
,LEVER
GEARSHIFTmHROTTLE
CONTROL LEVER
\
OIL PRESSURE
INDICATOR LIGHT
/
POWER T R I M ~ I L T
SWITCH
OVEI_UIEAT
iTOR LIGHT
FAST IDLE
LEVER
POWER TRIM/TILT
SPARE EMERGENCY
STOP SWITCH CLIP
SWITCH
IGNITION
SWITCH
BUZZER
(inside)
FAST IDLE
BUTTON
CONTROL LEVER
FRICTION ADJUSTER
EMERGENCY STOP
SWITCH LANYARD
EMERGENCY
STOP SWITCH
EMERGENCY STOP
SWITCH CLIP
12
NEUTRAL
RELEASE
LEVER
CONTROLS AND FEATURES
(SINGLE TOP-MOUNT REMOTE CONTROL)
(DUAL TOP-MOUNT REMOTE CONTROL)
GEARSHIFTRHROTTLE
CONTROL LEVER
GEARSHIFTRHROTTLE
CONTROL LEVERS
POWER TRIM/TILT
SWITCH (RIGHT)
POWER TRIM/TILT
SWITCH (LEFT)
CONTROL PANEL
(for PANELROP-MOUNT type)
FAST IDLE
BUTTON
OIL PRESSURE
INDICATOR LIGHT
BUTTON
INDICATOR LIGHT
EMERGENCY
STOP SWITCH CLIP
EMERGENCY
STOP SWITCH
LANYARD
EMERGENCY
STOP SWITCH
13
CONTROLS AND FEATURES
Fuel Tank (optional equipment)
Trim Meter
(optional equipment)
FUEL GAUGE
\
\
VENT KNOB
/
FUEL
FUE TANK
(optional
equipment)
(opti
FUEL CAP
(standard equipment)
/
PRIMING
(female) BULB
14
F&L HOSE CONNECTOR
CONTROLS AND FEATURES
CONTROLS
Turning the ignition switch key to the
START position operates the starter
motor. The key automatically returns
to the ON position when released
from the START position.
Side-MountType
Ignition Switch
The ignition switch can be used to
operate the starter motor only when
the control lever (p. 17 ) is in the N
(neutral) position, and the clip is in
the emergency stop switch.
Turning the ignition switch to the
OFF position stops the engine.
ON
H
The ignition switch controls the
ignition system and starter motor.
15
!
CONTROLS AND FEATURES
Switch Clip and Emergency Stop
Switch
EMERGENCY
STOP SWITCH
\
The switch clip must be inserted in
the emergency stop switch in order
for the engineto start and run. The
lanyard must be attached to the
operator’s PFD (Personal Flotation
Device) or worn around the wrist as
shown.
Gearshift/Throttle Control
Lever
CONTROL LEVER
When used as described, the
emergency stop switch and lanyard
system stops the engine if the
operator falls away from thecontrols.
SWITCH CLIP
A spare switch clip is stored in a slot
in the control housing (optional
equipment).
SWITCH CLIP
SPARE SWITCH CLIP
16
The gearshiftlthrottle control lever
controls engine speed and selects F
(forward), N (neutral), or R (reverse)
gears.
CONTROLS AND FEATURES
Moving thecontrol lever 30" from N
(neutral) selects the gear, and further
movement increases engine speed.
N (NEUTRAL)
The control lever automatically locks
itself in the N (neutral) position. To
move the lever out of the N (neutral)
position, you must squeeze the
neutral release lever on the underside
of the lever handle.
A friction adjuster near the base of
the control lever(s) adjusts the
operating resistance of the control
lever(s).
Less friction allows easier control
lever movement. More frictionhelps
to hold a steady throttle setting while
cruising.
GEARSHIFI'RHROTTLE
CONTROL LEVER
17
CONTROLS AND FEATURES
Fast Idle Lever
Panel-Mount Type
N (neutral)
n
IMUM FAST IDLE
Ignition Switch
ON
START
LOWEST POSITION
ST IDLE LEVER
The fastidle lever is only needed for
starting carbureted outboard models.
The BF115A and BF130A models
use programmed fuel injection so,
this lever will not be neededfor
starting.
The fastidle lever will not move
unless the remote control lever is in
the N (neutral) position. Conversely,
the remote control lever will not
move unless the fast idle lever is in
the lowest position.
After the engine starts and if the
outside temperature is below 41°F
(5"C), the fast idle lever can be used
to accelerate engine warmup.
Lower the fast idle lever to the
lowest position to decrease the fast
idle.
18
'\
IGNITION
SWITCHKEY
The ignition switch controls the
ignition system and starter motor
CONTROLS AND FEATURES
Turning the ignition switch key to the
START position operates the starter
motor. The key automatically returns
to the ON position when released
from the START position.
Switch Clipand Emergency Stop
Switch
EMERGENCY
STOP SWITCH
The ignition switch can be used to
operate the starter motor only when
the control lever (p. 21 ) is in the N
(neutral) position, and the clipis in
the emergency stop switch.
Turning the ignition switch to the
OFF position stops the engine.
The switch clip must be inserted in
the emergency stop switch in order
for the engine tostart and run. The
lanyard must be attached to the
operator's PFD (Personal Flotation
Device) or worn around the wrist as
shown.
When used as described, the
emergency stop switch and lanyard
system stops the engine if the
operator falls away from the controls.
SWITCH CLIP
\
LANYARD
A spare switch clip is stored in the
tool bag (optional equipment).
SPARE SWITCHCLIP
SWITCH CLIP
19
'
CONTROLS AND FEATURES
Fast Idle Button
N (neutral)
It is necessary to position the control
lever in N (neutral) to push in the fast
idle button.
Gearshift/Throttle Control
Lever
CONTROL LEVER
LEVER
FAST IDLE BUTTON
By moving the control lever forward
or reverse when the fast idlebutton is
pushed in, the throttle opening will
be increased without engaging the
gears.
The gearshifthhrottle control lever
controls enginespeed and selects F
(forward), N (neutral), or R (reverse)
gears.
CONTROLS AND FEATURES
Moving thecontrol lever 35" from N
(neutral) selects the gear, and further
movement increases engine speed.
N (NEUTRAL)
The control lever automatically locks
itself in the N (neutral) position. To
move thelever out of the N (neutral)
position, you must squeeze the
neutral release lever on theunderside
of the lever handle.
I
A friction adjuster near the base of
the control lever(s) adjusts the
operating resistance of the control
lever(s).
Less friction allows easier control
lever movement. More frictionhelps
to hold a steady throttle setting while
cruising.
MAXIMUM
'
x
?
?
GEARSHIFTmHROTTLE
CONTROL LEVER
21
CONTROLS AND FEATURES
~
Top-Mount Type
Ignition Switch
ON
START
I
Switch Clip andEmergency Stop
Switch
EMERGENCY
STOP
SWITCH
The ignition switch can be used to
operate the starter motor only when
the control lever (p. 24 ) is in the N
(neutral) position, and the clip is in
the emergency stop switch.
OFF
IGNITION
SWITCH
KEY
Turning the ignition switch key to the
START position operates the starter
motor. The key automatically returns
to the ON position when released
from the START position.
/\
Turning the ignition switch to the
OFF position stops the engine.
LANYARD
The ignition switch controls the
ignition system and starter motor.
SWITCH CLIP
22
CONTROLS AND FEATURES
The switch clip must be inserted in
the emergency stop switch in order
for the engine to start and run. The
lanyard must be attached to the
operator’s PFD (Personal Flotation
Device) or worn around the wrist as
shown.
Gearshift/Throttle Control
Lever
Fast Idle Button
N (neutral)
p-,y
F (forward)
When used as described, the
emergency stop switch and lanyard
system stops the engine if the
operator falls away from the controls.
CONTROL
LEVER
SINGLE
DUAL
A spare switch clip is stored in the
tool bag (optional equipment).
Push
FAST IDLE BUTTON
SPARE SWITCH CLIP
By moving the control lever forward
or reverse when the fast idlebutton is
pushed in, the throttle opening will
be increased without engaging the
gears.
It isnecessary to position the control
lever in N (neutral) to push in the fast
idle button.
CONTROL
LEVERS
The gearshifdthrottle control lever
controls engine speed and selects F
(forward), N (neutral), or R (reverse)
gears.
23
i
CONTROLS AND FEATURES
Moving the control lever 35" from N
(neutral) selects the gear, andfurther
movement increases engine speed.
A friction adjuster inside the control
box adjusts the operating resistance
of the control lever(s).
N (NEUTRAL)
F (FORWARD)
35"
Less frictionallows easier control
lever movement. More frictionhelps
to hold a steady throttle setting while
cruising.
REMOAT CONTROL LEVER
24
R (REVERSE)
CONTROLS AND FEATURES
The power tridtilt switch is located
on the control lever. It is a rocker
switch with UP and DN (down)
positions for changing the angle of
the outboard motor.
Common Controls
Power Trim/T.ilt Switch
(top-mount type)
(side-mount type)
SINGLE TYPE
POWER TRIM/TILT SWITCH
CONTROL
LEVER
TRIM/TILT
SWITCH
CONTROL
LEVER
(panel-mount type)
POWER TRIM/TILT SWITCH
CONTROL LEVER
DUAL TYPE
POWER TRIM/TILT SWITCH
You can use the power tridtilt
switch anytime the ignition switch is
ON, whether the boat is underway or
stopped.
Trim theoutboard motor to obtain
the best performance and stability (p.
51 ).
Tilt the outboard motor for shallow
water operation, beaching, launching,
or mooring.
25
CONTROLS AND FEATURES
Power Tilt Switch
Manual Relief Valve
Tilt Lock Lever
TILT LOCK
MANUAL RELIEF VALVE
FREE
LEVER
POWER TILT SWITCH
The power tilt switch is located on
the enginepan. It is a rocker switch
with UP and DN (down) positions
for changing the angleof the
outboard motor.
The power tilt switch will operate
without turning the ignition switch
ON.
This switch is used with the engine
stopped to raise the outboard motor
for mooring, trailering or
maintenance.
26
The outboard motor can be tilted
manually after opening the manual
relief valve. This allows :he outboard
motor to be tilted when no battery is
connected.
The tilt lock lever is used to support
the outboard motor in the fully-raised
position.
When the boat is to be moored for a
long time,tilt the outboard motor as
far as it will go. Then move thetilt
lock lever to the LOCK position, and
gently lower the outboard motor until
the lever contacts the stem bracket.
CONTROLS AND FEATURES
Engine Cover LockLevers
Transom Angle AdjustingRod
The transomangle adjusting rod
limits the tilt angle of the outboard
motor when fully lowered.
Proper adjustmentprevents the
outboard motorfrom being trimmed
too low (p. 5 1 ).
ENGINE COVER
LOCK LEVER
FREE
FRONT
A
TRANSOM ANGLE
ADJUSTING ROD
I
L
ENGINE COVER
LOCK LEVER
The engine coverlock levers fasten
the engine coverto the outboard
motor.
NUT
27
~
CONTROLS AND FEATURES
INSTRUMENTS
T=imTab
TRIMTAB
TIGHTENING
BoLT
The trim tab compensates for
"
torque steer," which is a reaction of
the out board motorto propeller
rotation.
If uncompensated, torque steer would
make the outboard motortend to turn
to one side.
When the trim tab is correctly
adjusted (p. 60),steering effort is
equal in either direction.
28
Tachometer
(optional equipment)
Trim Meter
(optional equipment)
TRIM METER
The trim meter has a range of 0" to
20" and indicates the trim angle of
the outboard motor.
Refer to the trim meter when using
the power tridtilt switch to achieve
the best performance frolnthe boat.
t
TACHOMETER
The tachometer shows engine speed
in revolutions per minute.
Refer to the tachometer when using
the throttle and powertrimhilt
controls to achieve the best
performance from the boat.
CONTROLS AND FEATURES
Fuel Gauge
(optional equipment)
Programmed Fuel Injection
(PGM-FI) Indicator
INDICATORS
Alternator (ACG) Indicator
ACG INDICATOR LIGHT
FUEL GAUGE
A fuel gauge isbuilt into the capof
the portable fuel tank (optional
equipment).
PGM-FI INDICATOR LIGHT
6
2
3
0
o
n
0
0
The ACG indicator light turns on and
the buzzer sounds when the charging
system is faulty.
The PGM-FI indicator light turns on
and the buzzer sounds when the
engine control system detects a
malfunction, and momentarily
sounds when the ignition key is
turned from OFF to ON.
29
CONTROLS AND FEATURES
Oil Pressure Indicator
When the green light is lit, oil
pressure is OK.
(side-mount type)
Overheating Indicator
(side-mount type)
If oil pressure becomes low, the
green light will go off, and the
engine protection system will limit
engine speed.
Remote controls are also equipped
with a buzzer that sounds whenthe
green light goes off.
(panel-mounthopmount types)
30
Low oil pressure indicates that the
engine oil level is low, or that there is
a problem with the engine lubrication
system.
(panel-mountltop-mounttypes)
CONTROLS AND FEATURES
If the engineoverheats, the red light
will come on, and the engine
protection system will limit engine
speed.
Cooling System Indicator
OTHER FEATURES
Overrev Limiter
The engine isequipped with an
overrev limiter to prevent the
possibility of mechanical damage
from excessive engine speed.
Remote controls are also equipped
with a buzzer that sounds when the
red light comes on.
Engine overheating may be theresult
of clogged water intakes.
COOLING SYSTEM INDICATOR
Water should flow fromthe cooling
system indicator while the engine is
running. This shows that water is
circulating through the cooling
system.
The overrev limiter may be activated
during operation, limiting engine
speed, if the outboard motor is tilted
excessively, or when ventilation
occurs during a sharp turn.
If the overrev limiter is activated,
check the trim angle of the outboard
motor.
If water stops flowingwhile the
engine is running, that indicates a
cooling system problem, such as
clogged water intakes, which will
cause engine overheating.
31
'
CONTROLS AND FEATURES
Anodes
Portable Fuel Tank
(optional equipment)
Fuel Cap Vent Knob
(optional equipment)
VENT KNOB
FUEL CAP
The anodes are made of a sacrificial
material that helps to protect the
outboard motor from corrosion.
There are two anodeson the gear
case, one onthe stern bracket, and
two small anodes in the water
passages of the engineblock.
32
The portable fueltank (optional
equipment) has a capacity of 6.6 US
gal (25 a ) and has a fuel gauge built
into thecap.
The cap isprovided with a vent knob
to seal the portable fuel tank
(optional equipment) for carrying it
to and from theboat. Open the vent
knob 2 or 3 turns before starting the
engine (p. 39 ).
CONTROLS AND FEATURES
Fuel Priming Bulb
OUTLET END
(MOTOR)
PRIMING BULB
INLET END
(TANK)
A priming bulb is built into the fuel
hose that connects the fuel tank to the
outboard motor.
Before starting the engine, hold the
priming bulb up in the direction of
the arrow, then squeeze the priming
bulb until it feels firm. Thiswill
ensure that fuel is supplied to the
engine (p. 39 ).
33
BEFORE OPERATION
ARE YOU READYTO GET
UNDER WAY ?
Your safety isyour responsibility. A
little time spent in preparation will
significantly reduce your risk of
injury.
Safety
Always wear a PFD (Personal
Flotation Device) while on the boat.
Attach the emergency stop switch
lanyard securely to your PFD or to
your wrist.
Improperly maintaining this
outboard motor, or failing to
correct aproblem before
operation, could cause a
malfunction in which you could
be seriously injured.
Knowledge
Read and understand this manual.
Know what the controls do and how
to operate them.
Familiarize yourself with the
outboard motor and its operation
before you get under way. Know
what to do in case of emergencies.
Familiarize yourself with all laws
and regulations relating to boating
and the use of outboard motors.
34
IS YOUR OUTBOARD
MOTOR READY TO GO ?
For your safety, and to maximize the
service life of your equipment, it is
very important to take a few
moments before you operate the
outboard motor to check its condition.
Be sure totake care of any problem
you find, or have your authorized
Honda Marine dealer correct it,
before you operate the outboard
motor.
Always perform a preoperation
inspection before each operation,
and correct any problem.
Before beginning your preoperation
checks, be sure theignition switch is
in the OFF position.
BEFORE OPERATION
Safety Inspection
Look around the outboard motor
for signs of oil or gasoline leaks.
Check that all fasteners are in
place and securely tightened.
Maintenance Inspection
Check the engine oil level (p. 63 ).
Running the engine with a low oil
level can cause engine damage.
If you are using the portable fuel
tank (optional equipment), make
sure it is in good condition and
properly secured in the boat (p.
38 ).
Check to be sure the propeller is
undamaged, andthe castle nut is
secured with the cotter pin (p. 77 ).
Check that the fudIhamimMs
undamaged andproperly
connected (p. 38 ).
Check that the anodes are securely
attached to the gear case (p. 76)
and are not excessively worn. The
anodes help to protect the outboard
motor fromcorrosion.
Wipe up anyspills before starting
the engine.
Check the stem bracket to be sure
the outboard motoris securely
installed.
Make sure the tool kit is onboard
(p. 57 ). Replace any missing items.
Check the fuel level in the fuel
tank (p. 71 ).
Check that all controls are
operating properly.
Replace any damaged parts.
35
OPERATION
SAFE OPERATING
PRECAUTIONS
To safely realize the fullpotential of
this outboard motor, you need a
complete understanding of its
operation and a certain amount of
practice with its controls.
Before operating the outboard motor
for the first time, please review the
IMPORTANT SAFETY
INFORMATION on page 7 and the
chapter titled BEFORE OPERATION.
For your safety, avoid starting or
operating the enginein an enclosed
area. Your engine’sexhaust contains
poisonous carbon monoxide gas
which can collect rapidly in an
enclosed area and cause illness or
death.
36
BREAK-IF PROCEDURE
Break-in period: 10 hours
Proper break-in operation allows the
moving parts to wear in smoothly for
best performance and long service
life.
Next 60 minutes:
Run the engineup to a maximum of
4,000 to 5,000 rpm, which is about
50% to 80% of maximum throttle
opening.
Short full-throttlebursts are OK, but
do not operate the engine
continuously at full throttle.
First 15 minutes:
Run the engine at trolling speed. Use
the minimum throttle opening
necessary to operate the boat at a safe
trolling speed.
For boats that plane easily, bring the
boat up on plane, and then reduce the
throttle opening to the recommended
rpm range.
Next 45 minutes:
Next 8 hours:
Run the engine up to a maximum of
2,000 to 3,000 rpm, which is about
10% to 30% of maximum throttle
opening.
Do not run the engine at full throttle
for more than 5 minutes at a time.
OPERATION
TRANSOM ANGLE
ADJUSTMENT
The transom angle adjusting rod
limits the tilt angle of the outboard
motor when fully lowered.
Proper adjustment prevents the
outboard motor from being trimmed
too low (p. 51 ).
Do not allowwater to enter theidle
exhaust port or the
engine can be
damaged.
To adjust, first tilt the outboard
motor so it is not resting on the rod.
Remove thenut, then remove the rod
and insert it in the desired position.
Reinstall the nut and tighten it
securely.
TRANSOM ANGLE
ADJUSTING ROD
NUT
37
1
OPERATION
PORTABLE FUEL TANK
(optional
equipment)
Secure the portable fuel tank in the
boat, so it won’t move around and
become damaged.
FUEL HOSE CONNECTIONS
FUEL HOSE CONNECTOR
Before use, open the fuel tank vent
by turning the vent knob at least 2 or
3 turns counterclockwise.
Gasoline is highly flammable
and explosive.
(FUEL TANK SIDE)
Place the portable fuel tank (optional
equipment) in a well-ventilated
location, away from direct sunlight,
to reduce the possibility of a gasoline
vapor explosion.
You can be burned or seriously
injured when handling fuel.
0
FUEL HOSE CONNECTOR
Stop the engine and keep heat,
sparks, and flame away.
Handle fuel onlyoutdoors.
To ensure that the outboard motor
will be ableto draw fuel from the
tank, place the tank within 6 feet of
the outboard motor and not more
than 3 feet below the fuel connector
on the outboard motor.
38
Wipe up spills immediately.
(OUTBOARD MOTOR SIDE)
Connect the fuel hose to the
tank and
the outboard motor, as shown. Be
sure both connectors snap securely
into place.
OPERATION
STARTING THE ENGINE
FUEL PRIMING
The enginewill not start or run,
unless the clip is in the switch.
Side-Mount Type
OUTLET END
(MOTOR)
The emergency stop switch clip
and lanyard system is a safety
device that will stop the engine if
you fall away from thecontrols
while operating the boat.
EMERGENCY
STOP SWITCH
PRIMING BULB
/
Always attach the lanyard to your
PFD, orto your wrist, before
starting the engine.
INLET END
(TANK)
Hold the priming bulb up in the
direction of the arrow, then squeeze
the priming bulb several times until it
feels firm, indicating that fuel has
reached the engine.
Check to be sure there are no fuel
leaks before starting the engine.
SWITCH CLIP
\
LANYARD
1. Put the emergency stop switch clip
in the emergency stop switch, and
attach the lanyard to your PFD
(Personal Flotation Device) or to
your wrist, as shown.
Do not squeeze the priming bulb
when the engineis running.
39
OPERATION
N (neutral)
I
C
L
FAST IDLE RANGE
2. Set thecontrol lever in the N
(neutral) position.
The engine will not start if the F
(forward) or R (reverse) gears are
engaged.
3. Leave the fast idle lever in the
OFF (fully lowered) position.
Fast idle lever cannot be raised
unless the control lever is in the N
(neutral) position.
The control lever cannot be moved
away from the N (neutral) position
unless the fast idlelever is lowered.
40
IGNITION SWITCH KEY
4. Turn the ignition switch key to the
START position and hold it there
until the engine starts.
When the engine starts, release the
key, allowing it to return to the ON
position.
If the engine fails to start within 5
seconds, release the key and wait
at least 10 seconds before
operating the starter again.
OPERATION
During the warm-up period, check
the oil pressure indicator (p. 30 ),
overheating indicator (p. 30), and
cooling system indicator (p. 3 1 ).
1Using the electric starter f or more
than 5 seconds at atime will
overheat the starter motor and can
damage it.
If the indicators show any
abnormal condition, immediately
stop the engine and determine the
cause of the problem. Refer to
TAKING CARE OF
UNEXPECTED PROBLEMS, p.
85 .
Turning the ignition switch key to
the START position while the
engine is running can damage the
starter motor and f lywheel.
5. Before getting under way, allow
the engine to warm up sufficiently
to ensure good performance.
Above 41°F (5"C),warm up the
engine for 2 or 3 minutes.
Below 41°F (5"C),warm up the
engine for at least 10 minutes at
2,000 rpm. Raise the fast idle lever
to achieve approximately 2,000
6. If the fast idle lever was used to
warm up the engine, gradually
lower the lever as the engine
warms up.
When the fast idle lever is fully
lowered, the control lever can be
moved away from the N (neutral)
position.
rpm-
41
1
OPERATION
Panel-Mount
Type
The enginewill not start or run,
unless the clip is in the switch.
EMERGENCY STOP
SWITCH
SWITCH CLIP
The emergency stop switch clip
and lanyard system is a safety
device that will stop the engine if
you fall away from the controls
while operating the boat.
\
LANYARD
1. Put the emergency stop switch clip
in the emergency stop switch, and
attach the lanyard to your PFD
(Personal Flotation Device) or to
your wrist, as shown.
42
N (neutral)
Always attach the lanyard to your
PFD, or to your wrist, before
starting the engine.
W
2. Set thecontrol lever in the N
(neutral) position.
The enginewill not start if the F
(forward) orR (reverse) gears are
engaged.
OPERATION
START
N (neutral)
0
0
SWITCH
KEY
\
,
Using the electric starter for more
than 5 seconds at a time will
overheat the starter motor and can
damage it.
Turning the ignition switch key to
the START position while the
engine is running can damage the
starter motor and flywheel.
C
L
\
FAST IDLE BUTTON
3. Turn the ignition switch key to the
START position and hold it there
until the engine starts.
When the engine starts, release the
key, allowing it to return to the ON
position.
If the engine fails to start within 5
seconds, release the key and wait
at least 10 seconds before
operating the starter again.
4. Before getting under way, allow
the engine to warm up sufficiently
to ensure good performance.
Above 41°F (5"C), warm up the
engine for 2 or 3 minutes.
Below 41 "F (5"C), warm up the
engine for at least 10 minutes at
2,000 rpm. Push the fastidle
button then move the control lever
forward or reverse to open the
throttle and achieve approximately
2,000 rpm.
43
OPERATION
During the warm-up period, check
the oil pressure indicator (p. 30 ),
overheating indicator (p. 30 ), and
cooling system indicator (p. 3 1 ).
Top-Mount Type
The enginewill not start or run,
unless the clip is in the switch.
EMERGENCY STOP
SWITCH
The emergency stop switch clip
and lanyard system is a safety
device that will stop the engine if
you fall away from the controls
while operating the boat.
If the indicators show any
abnormal condition, immediately
stop the engine and determine the
cause of the problem. Refer to
TAKING CARE OF
UNEXPECTED PROBLEMS, p.
85.
Always attach the lanyard to your
PFD, or to your wrist, before
starting the engine.
SWITCH CLIP
5. If the fastidle control was used to
warm up the engine, gradually
return the control lever to the N
(neutral) position as the engine
warms up.
44
LANYARD
1. Put the emergency stop switch clip
in the emergency stop switch, and
attach the lanyard to your PFD
(Personal Flotation Device) or to
your wrist, as shown.
OPERATION
START
N (neutral)
Using the electric starter
for more
than 5 seconds at a time will
overheat thestarter motor and can
damage it.
,,
0
2. Set the control lever in the N
(neutral) position.
The enginewill not start if the F
(forward) or R(reverse) gears are
engaged.
Turning the ignition switch key to
the START positionwhile the
engine is running can damage the
starter motorand flywheel.
3. Turn the ignition switch key to the
START position and hold it there
until the engine starts.
When the engine starts, release the
key, allowing it to return to the ON
position.
If the engine failsto start within 5
seconds, release the key and wait
at least 10 seconds before
operating the starter again.
45
OPERATION
I
N (neutral)
During the warm-up period,check
the oil pressure indicator (p. 30 ),
overheating indicator (p. 30 ), and
cooling system indicator (p. 3 1 ).
STOPPING THE ENGINE
Emergency Engine Stopping
Side-Mount Type
CONTROL
LEVER
FAST IDLE BUTTON
4. Before getting under way, allow
the engine to warm up sufficiently
to ensure good performance.
Above 41°F (5"C),warm up the
engine for 2 or 3 minutes.
Below 41°F (5"C), warm up the
engine for at least 10 minutes at
2,000 rpm. Push the fastidle
button then move the controllever
forward or reverse to open the
throttle and achieve approximately
2,000 rpm.
46
If the indicators show any
abnormal condition, immediately
stop theengine and determine the
cause of the problem. Refer to
TAKING CARE OF
UNEXPECTED PROBLEMS, p.
85.
EMERGENCY
STOP SWITCH
LANYARD
5. If the fast idle control was used to
warm up the engine, gradually
return the control lever to the N
(neutral) position as the engine
warms up.
Panel-Mount/Top-Mount Types
EMERGENCY
STOP SWITCH
SWITCH CLIP
'qNTRoL
OPERATION
To stop the engine in an emergency,
pull the clip outof the emergency
stop switch by pulling the lanyard.
We suggest that you stop the engine
this way occasionally to verify that
the engine and emergency stop
switch is operating properly.
Normal Engine Stopping
Top-Mount Type
Side-Mount Type
N (neutral)
N (neutral)
I
LEVER
Panel-Mount Type
1 . Move the control lever(s) to the N
(neutral) position.
N (neutral)
47
~
OPERATION
3. When the boat is not in use,
remove and store the ignition key
and the emergency stop switch clip
and lanyard.
Side-Mount Type
GEARSHIFTING AND
THROTTLE OPERATION
Side-Mount Type
CONTROL LEVER
Panel-Mount/Top-Mount Types
N (neutral)
T(cl?
OFF
F (forward)
IGNITION KEY
\
2. Turn the ignition switch key to the
OFF position.
48
OPERATION
Panel-Mount Type
To shift gears, move the control lever
to select F (forward), N (neutral) and
R (reverse) gears.
Side-Mount Type
N (neutral)
F (forward)
-;
The control lever cannot be moved
from the N (neutral) position unless
the neutral release lever is squeezed
(side-mountlpanel-mount types).
,/'
CONTROL
LEVER
Moving thecontrol lever beyond the
gear selection range increases engine
speed.
Top-Mount Type
FRICTION
ADJUSTER
TO DECREASE
Panel-Mount Type
N (neutral)
\FW,y-
F (forward)
CONTROL LEVER
FRICTION ADJUSTER
\-
CONTR
LEVER
TO DECREASE
FRICTION
49
OPERATION
Top-Mount Type
0
FRICTION
I
CONTROL LEVER
FRICTION ADJUSTER
Adjust the throttle friction adjuster so
the control lever will hold a constant
throttle setting while cruising.
50
STEERING
Steer theboat in the same manner as
an automobile.
OPERATION
CRUISING
motor.
Engine Speed
Trim
For best fuel economy,limit the
throttle opening to 80%. Use the
throttle friction control (p. 49 ) to
help you hold a steady speed.
Use the power tridtilt switch to trim
the outboard motor for the best
performance and stability.
For rough water conditions or large
waves, slow down to prevent the
propeller from rising out of the water.
The engineis equipped with an
overrev limiter to prevent the
possibility of mechanical damage
from excessive engine speed.
If, forexample, the outboard motor
is tilted excessively, or ventilation
occurs during a sharpturn, the engine
may overrev, activating the overrev
limiter.
If engine speed becomes unstable at
high speed due to activation of the
overrev limiter, reduce speed and
check the trim angle of the outboard
You can use the power tridtilt
switch at any time, whether the boat
is under way or stopped.
Press the UP orDN (down) side of
the switch to adjust the angle of the
outboard motor.
antiventilation plate is level with the
water.
When cruising into a high wind, trim
the outboard motor down slightly to
level the boat and improve stability.
With a tail wind, trim the outboard
motor up slightly.
Excessive tridtilt angle during
operation can cause propeller
ventilation, overheating, and water
pump damage.
Refer to the trim meter (p. 28) for an
indication of whether the boat is
trimmed high or low.
It is necessary to trim the angle of the
outboard motor to compensate for
changes in boat load, weight
distribution, water conditions, or
propeller selection.
Under normal conditions, the boat
will perform best when the
51
~
OPERATION
Side-Mount
Type
Top-Mount Type
(single type)
POWER TRIM/TILT SWITCH
MOTOR
TRIMMED TOO
LOW
MOTOR
TRIMMED TOO
HIGH
POWER TRIM/TILT §WITCH
I
WAVES
Panel-Mount Type
POWER TRIM/TILT SWITCH
(dual type)
MOTOR TRIMMED
CORRECTLY
BOW TOO LOW DUETO
1. LOAD IN THE FRONT
2. MOTOR TRIMMED TOO LOW
POWER TRIM/TILT SWITCH
(RIGHT)
BOW TOO HIGH DUETO
1. LOAD IN THEREAR
2. MOTOR TRIMMED TOO HIGH
52
OPERATION
If steering effort is not equal in both
directions, adjust the trim tab to
compensate for “torque steer,”
which is thereaction of the outboard
motor to propeller rotation.
TIGHTENING BOLT
SHALLOW WATER
OPERATION
MOORING, BEACHING,
LAUNCHING
When operating in shallow water, use
the power tridtilt switch (p. 52 ) to
tilt the outboard motor, so the
propeller and gear case won’t hit the
bottom.
To raise the outboard motor out of
Proceed at low speed, and monitor
water flow fromthe cooling system
indicator (p. 3 1 ) to be sure the
outboard motor is not tilted so high
that the water intakes are out of the
water.
psiq
Adjust the trim tab with the engine
stopped. Loosen the bolt above the
trim tab, turn the trim tab, then
tighten the bolt securely.
When the trim tab is correctly
adjusted, steering effort will be equal
in both directions.
An excessive tridtilt angle during
operation can cause propeller
ventilation, overheating, and water
pump damage. This type of damage
is not covered by the Distributor’s
Limited Warranty.
the water while the engine is stopped
and the boat is moored, or for
maximum clearance when beaching
or launching, use the power tilt
switch on the enginepan to tilt the
outboard motor as far asit will go,
move thetilt lock lever to the LOCK
position, then gently lower the
outboard motor until the lever
contacts the stem bracket.
If more clearance is needed to swing
the tilt lock lever into the LOCK
position, rock the outboard motor
back slightly by pulling on the engine
cover grip.
To lower the outboard motor, tilt up,
move thetilt lock lever to the FREE
position, then lower the outboard
motor to the desired position.
53
OPERATION
Do notattempt to use the power tilt
switch to tilt the outboard motor
down while the tilt lock lever is in the
lock position. Damage to the power
tilt system may occur.
MANUAL RELIEF VALVE
POWER TILT SWITCH
MANUAL
(To-release)
TILT LOCK
LEVER
(Lock position)
FREE
/
The outboard motor canalso be tilted
manually after opening the manual
relief valve. This featureenables the
outboard motorto be tilted when no
battery is connected.
54
For manualtilting, use a screwdriver
to turn the valve counterclockwise 1
or 2 turns. Close the valve firmly
after positioning the engine.
Be sure the valve is closed before
operating the outboard motor. If the
valve is not closed, the outboard
motor will tilt up when operated in
reverse.
SERVICING YOUR OUTBOARD MOTOR
THE IMPORTANCE OF
MAINTENANCE
Good maintenance is essential for
safe, economical, and trouble-free
operation. It will also help reduce air
pollution.
Improperly maintaining this
outboard motor, or failureto
correct a problem before
operation, can cause a
malfunction in which you could
be seriously hurt or killed.
Always follow the inspection
and maintenance
recommendations and schedules
in this owner’s manual.
To help you properly care for your
outboard motor, the followingpages
include a maintenance schedule,
routine inspection procedures, and
simple maintenance procedures using
basic hand tools. Other service tasks
that are more difficult, or require
special tools, are best handled by
professionals and are normally
performed by a Honda technician or
other qualified mechanic.
The maintenance schedule applies to
normal operating conditions. If you
operate your outboard motor under
unusual conditions, consult an
authorized Honda marine dealer for
recommendations applicable to your
individual needs and use.
Remember that your authorized
Honda marine dealer knowsyour
outboard motor best and is fully
equipped to maintain and repair it.
To ensure thebest quality and
reliability, use only new, genuine
Honda parts or their equivalents for
repair and replacement.
Maintenance, replacement, or
repair of the emission control
devices and systems may be
performed by any marineengine
repair establishment or individual,
using parts that are “certified” to
EPA standards.
1
~
SERVICING YOUR OUTBOARD MOTOR
MAINTENANCE
SAFETY
Some of the most important safety
precautions follow. However, we
cannot warn you of every
conceivable hazard that can arise in
performing maintenance. Only you
can decide whether or not you should
perform a given task.
'
Safety Precautions
Make sure the engine is off before
you begin any maintenance or
repairs. This will eliminate several
potential hazards:
- Carbon
monoxidepoisoning
from engine exhaust.
Be sure there is adequate
ventilation whenever you
operate the engine.
Failure toproperly follow
maintenance instructions and
precautions can cause you to be
seriously hurt or killed.
-Burns from hotparts.
Let the engine and exhaust
system cool before touching.
Always follow the procedures
and precautions in the owner's
manual.
-Injury from movingparts.
Do not run the engine unless
instructed to do so.
56
Read the instructions before you
begin, and make sure you have the
tools and skills required.
To reduce thepossibility of fire or
explosion, be carefulwhen
working around gasoline. Use only
a nonflammable solvent,not
gasoline, to clean parts. Keep
cigarettes, sparks, and flames away
from all fuel-related parts.
Wear gloves when handling the
propeller to protect your hands
from sharp edges.
--
SERVICING YOUR OUTBOARD MOTOR
TOOL KIT
(optional equipment)
The followingtools are supplied by
your dealer for simple maintenance
procedures and emergencyrepairs.
Keep these items on the boat, so they
will always beavailable if you need
them.
14 X 17 mm WRENCH
-
BOX WRENCH
10 X 12 nun WRENCH
-
PLIERS
8 mm WRENCH
FLAT SCREWDRIVER
C
0
3
SCREWDRIVER HANDLE
~
TOOL BAG
PHILLIPS SCREWDRIVER
GEAR OIL CHECK SCREWDRIVER
SPARK PLUG WRENCH
SPARE SWITCH CLIP
57
SERVICING YOUR OUTBOARD MOTOR
MAINTENANCE SCHEDULE
REGULAR SERVICE PERIOD (3)
Perform at everindicated month or
operating hour interval, whichever
case
Gear
oil
Engine oil filter
Timing belt
Throttle linkage
Idling speed
Valve clearance
Spark plug
Propeller (cotter pin)
Anode
Lubrication
Each use
Every 6 months
First month
or
20 hrs.
or
100 hrs.
Every year
or
200 hrs.
Every 2 years
or
400 hrs.
Change
Check level
Check for water contamination
Replace
Check-adiust
Check-adjust
Check-adjust
Check-adjust
Check-adjust
Replace
Check
Check
Grease
I
0(2)
I
I
0
0
0(1)
I
0(1)
Emission-related items.
(1) Lubricate more frequently when used in salt water.
(2) These items should be servicedby an authorized Honda marine dealer, unless you have the proper tools and are mechanically proficient.
Refer to the Hondashop manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
SERVICING YOUR OUTBOARDMOTOR
Fuel line
Battery and cable
Bolts and Nuts
Breather element
Check
Check (Replace if necessary)
Check
Check-tightness
Check
0
Every 2 years (2)
0
0 (2)
0(2)
0
0 (2)
0 (2)
Emission-related items.
(1) Lubricate more frequently when used insalt water.
(2) These items should be servicedby an authorized Honda marine dealer, unless you have the proper tools and
are mechanically proficient.
Refer to the Hondashop manual for service procedures.
(3) For commercial use, log hoursof operation to determine proper maintenance intervals.
59
SERVICING YOUR OUTBOARDMOTOR
TRIM TAB ADJUSTMENT
1
The trim tab compensates for
“torque steer” which is a reaction of
the outboard motorto propeller
rotation.
Q
If uncompensated, torque steer would
make the outboard motortend to turn
to one side.
RIG
When the trim tab is correctly
adjusted, steering effort is equalin
either direction.
TRIM TAB
If steering effort is unequal, loosen
the trim tab bolt and adjust the angle
of the trim tab. Retighten the trim tab
bolt securely.
\
TIGHTENING BOLT
If less effort is required to make left
turns, move the back of the trim tab
left.
TRIM TAB
\
TIGHTENING BOLT
If less effort isrequired to makeright
turns, move the back of the trim tab
right.
Adjust the trim tab in small
increments, and retest steering effort
with the boat evenly loaded and
running at cruising speed.
60
SERVICING YOUR OUTBOARD MOTOR
MANUAL RELIEF VALVE
MANUAL RELIEF VALVE
ENGINE COVER REMOVAL
AND INSTALLATION
FRONT
0 UNLOCK
I
To remove the engine cover, turn
both front and side levers to the
unlocked position, then lift the
engine cover off theoutboard motor.
To install the engine cover, place the
cover on the outboard motor, then
turn both front and side lock levers to
the locked position.
L
The outboard motor can be tilted
manually after opening themanual
relief valve. This featureenables the
outboard motor to be tilted when no
battery is connected.
ENGINE COVER LOCK LEVER
'IDE
COVER
LOCK LEVER
For manual tilting, use a screwdriver
to turn the valve counterclockwise 1
or 2 turns. Close the valve firmly
after positioning the outboard motor.
Be sure the valve is closed before
operating the outboard motor. If the
valve is not closed, theoutboard
motor will tilt up when operated in
reverse.
UNLOCK
The engine coverlock levers fasten
the engine cover to the outboard
motor.
61
I
SERVICING YOUR OUTBOARD MOTOR
Lock Lever Adjustment
A loose engine covermay rattle or
allow waterto enter. Check whether
the engine cover fitsproperly and
adjust if necessary.
Engine Cover Clearance
Inspection
FRONT
I
I
I
'
- 0.23 in
? 0.19
(4.8 - 5.8 mm)
w
q
REAR
I
!I
I
0.19 - 0.23 in
(4.8 - 5.8 mm)
INSPECTION POINT
With the engine coverin place and
both front andside lock levers in the
locked position, measure the
clearance between the engine cover
and the engine undercaseat the lock
levers.
Lock Lever Bracket
Adjustment
1. Remove the engine cover.
RETAINING BOLT
2. Loosen the retaining bolts on the
front and/or side lock lever
brackets, and move the bracket(s)
as necessary to obtain the specified
engine coverclearance.
3. After adjustment, tighten the
INSPECTION POINT
Specified engine coverclearance:
0.19 - 0.23 in (4.8 - 5.8mm)
If the clearance is outside the
specified range, adjust the lock lever
brackets.
62
retaining bolts securely, and install
the engine cover.
4. Recheck the engine cover
clearance, and readjust if necessary.
SERVICING YOUR OUTBOARD MOTOR
Engine Oil Level Check
Engine Oil Change
OIL FILLER CAP
Check the engine oil level with the
engine stopped andthe outboard
motor in the vertical position.
An engine oil evacuatiodfilling
device may be used to removeladd
the engine oil.
1. Unlock and remove
the engine
cover (p. 61 ).
Drain the used oil while the engine is
warm. Warm oil drains quickly and
completely.
2. Remove the dipstick and wipeit
clean.
1. Unlock and removethe engine
cover (p. 61 ).
DRAINPLUG
4. If the oil level is low, remove the
oil filler cap, and addoil to reach
the upper limit mark shown onthe
dipstick. Use the oil recommended
on p. 66.
m
OIL LEVEL DIPSTICK
3. Insert the dipstick all the way in,
then remove it and checkthe oil
level shown on the dipstick.
Running the engine with a low oil
level can cause engine damage.
5. Install the oil filler cap and tighten
it securely.
6. Install and lock the engine cover.
SCREW
I
DRAIN PLUG COVER
2. Remove the screw from the oil
drain cover, and removethe cover.
63
SERVICING YOUR OUTBOARD MOTOR
WASHER
GUIDE\
I
DRAIN PLUG
I
k
3. Place a suitable container below
the oil drain guide to catch the
used oil, then remove the oil filler
cap and the drain plug.
4.Allow the used oil to drain
completely, then reinstall the
engine oil drain plug, and tighten it
securely.
1-
Improper disposalof engine oil
1. Drain the engine oil,and reinstall
the drain plug and oil drain cover
can be harmful to the environment.
(see Engine Oil Change on p. 63 ).
If you change yourown oil, please
dispose of the used oil properly.
2. Tilt the outboard motor, and place
Put it in a sealed container, and
a suitable container below the oil
take it to a recycling center. Do
drain guide to catch the used oil.
not discard it in a trash bin or
dump it on the ground.
3. Use a suitable tool to remove the
oil filter, and throughly drain the
5. Install the oil drain cover and
filter into theused oil container.
secure it with the screw.
6. With the outboard motor in a
vertical position, fill to the upper
limit mark on the dipstick (p. 56)
with the recommended oil.
Engine oil refill capacity:
Without oil filter change:
5.9 US qt (5.6 €4,4.9 Imp qt)
With oil filter change:
6.9 US qt (6.5 e, 5.7 Imp qt)
7. Install the oil filler cap and tighten
it securely.
8. Install and lock the engine cover.
64
Oil Filter Change
SERVICING YOUR OUTBOARD MOTOR
USE A SUITABLE TOOL
4. Clean the oil filter mounting base,
and coat the gasket of the new oil
filter with clean engine oil.
Use only a genuine Honda oil
filter or a f ilter of equivalent
quality specified f o r your model.
Using the wrong f ilter, or a nonHonda f ilter which is not of
equivalent quality, may cause
engine damage.
OIL DRAIN GUIDE
5. Screw on the new filter by hand
until it contacts the engine, then
use suitable tool to tighten the
filter an additional 7/8 turn.
7. Start the engineand check for
leaks.
p
q
i
Running the engine without water
can cause serious engine damage.
If you are changing the oilf ilter
while the outboard motor is out of
the water, use the water hose
adapter (optionalpart) and a hose
to supply water.
8. Stop the engine, and check the oil
level as described on page 63. If
necessary, add oil to bring the oil
level to the upper limit mark on the
dipstick.
OIL FILTER TIGHTENING
TORQUE:
16 Ibf-ft(22 N-m ,2.2 kgf-m)
RUBBER SEAL
6. Return the outboard motor to the
vertical position,and fill the
crankcase with the specified
amount (p. 64 ) of the
recommended oil.
65
SERVICING YOUR OUTBOARD MOTOR
Engine Oil Recommendations
Oil is a major factoraffecting
performance and service life. Use
4-stroke automotive detergentoil.
SAE Viscosity Grades
AMBIENTTEMPERATURE
SAE 1OW-30 is recommended for
general use.
66
The SAE oil viscosity and service
classification are in the API label on
the oil container. Honda recommends
that you use API SERVICE category
SG, or SH oil with the “starburst”
certification mark displayed on the
container.
SERVICING YOUR OUTBOARD MOTOR
Gear Oil Level Check
Check thegear oil level with the
engine stopped and the outboard
motor in the vertical position.
If water or contaminated (milkycolored) oil flows out the oil level
hole when the plug is removed, have
the outboard motor checked by an
authorized Honda Marine dealer.
LEVEL
Remove the oillevel plug and see
whether oil flows fromthe oil level
hole.
If oil flows from the
oil level hole,
the oil level is OK. Reinstall the plug
and tighten it securely.
OIL LEVEL PLUG TORQUE:
2.5 lbfaft (3.4 N.m ,0.35 kgfam)
67
SERVICING YOUR OUTBOARD MOTOR
rRANSOM ANGLE
4DJUSTING ROD/
SWIVEL CASE
Apply Honda Marine Corrosion Inhibitor (or equivalent) to all areas under the enginecover except the belts.
68
SERVICING YOUR OUTBOARD MOTOR
Spark Plug Service
17 mm WRENCH
RECOMMENDED SPARK PLUGS:
ZFR7F (NGK)
KJ22CR-L8 (DENSO)
0.028 - 0.031 in
(0.70 - 0.80 mm)
1Incorrect spark plugs cancause
engine damage.
1. Unlock and remove the engine
cover (p. 61 ).
2. Disconnect the spark plug caps
from the spark plugs.
3. Remove the spark plugs with a
spark plug wrench and 17 mm
wrench.
SEARING WASHER
SPARK
WREN(
4.Inspect the spark plugs. Replace
them if the electrodes are worn, or
if the insulators are cracked or
chipped. Clean the spark plugs
with a wire brush if you are going
to reuse them.
5. Measure the spark plug electrode
gap with a suitable gauge. The gap
should be 0.028 - 0.031 inches
(0.70 - 0.80 mm).
69
I
G
SERVICING YOUR OUTBOARD MOTOR
PLUG 1
CllLIND
7. After eachspark plug seats, tighten
with a spark plug wrench supplied
in the tool kit to compress the
sealing washer.
PLUG 2
3
CYLIND
CYLINDER 3
If reinstalling the used spark plugs,
tighten 1/8 - 1/4 turn after the
spark plugs seat.
PLUG 4
CYLINDER 4
If reinstalling new spark plugs,
tighten 1/2 turn after the spark
plugs seat.
piiq
6. Install the spark plugs carefully,
by hand, to avoid cross-threading.
Loose spark plugs can over heat
and damage the engine.
Overtightening the spark plugs
can damage the threads in the
cylinder head.
8. Attach the spark plug caps. Each
cord is marked with a number near
the spark plug cap. Match the cord
numbers with the cylinder
numbers, as shown.
9. Install and lock the engine cover.
70
SERVICING YOUR OUTBOARD MOTOR
REFUELING
Portable Fuel Tank
(optional equipment)
Gasoline is highly flammable
and explosive.
FUEL TANKCAPACITY:
6.61 US gal (25.0 Q,5.50Imp
gal)
You can be burned or seriously
injured when handling fuel.
FUEL GAUGE
Check the fuel gaugeand refill the
tank when necessary.
Stop the engine and keep heat,
sparks, and flame away.
SAFE FILL LEVEL
Handle fuel only outdoors.
Remove the fueltank from theboat
for refueling.
Wipe up spills immediately.
VENT KNOB
Refuel in a well-ventilated area. Fill
the tank to the SAFE FILL LEVEL
line.
Never refill the fuel tank inside a
building where gasoline fumes may
reach flames or sparks. Keep
gasoline away from appliance pilot
lights, barbecues, electric appliances,
power tools, etc.
FUEL CAP
To refuel, turn the vent knob
counterclockwise to the OPEN
position, and unscrew the fueltank
cap.
After refueling, install the capand
tighten it securely. Turn the vent
knob clockwise to the CLOSED
position, and return the fueltank to
the boat.
Spilled fuel isnot only a fire hazard,
it causes environmental damage.
Wipe up spills immediately.
71
SERVICING YOUR OUTBOARD MOTOR
FUEL RECOMMENDATIONS
pimq
Use unleaded gasoline with apump
octane rating of 86 or higher.
Running the engine with persistent
spark knock or pinging can cause
engine damage.
These outboard motors are certified
to operate on unleaded gasoline.
Unleaded gasoline produces fewer
engine and spark plug deposits and
extends exhaust system life.
Never use stale or contaminated
gasoline or anoil/gasoline mixture.
Avoid getting dirt or water in the fuel
tank.
Occasionally you may hear a light
“spark knock” or “pinging”
(metallic rapping noise) while
operating under heavy loads. Thisis
no causefor concern.
If spark knock orpinging occurs at a
steady engine speed, under normal
load, change brandsof gasoline. If
spark knock or pinging persists, see
an authorized Honda marine dealer.
72
Running the enginewith persistent
spark knock orpinging is misuse,
and the Distributor’s Limited
Warranty does not cover parts
damaged by misuse.
SERVICING YOUR OUTBOARD MOTOR
Fuel Pump Filter Inspection
and Replacement
The fuel pump filter
is located under
the engine cover,between the fuel
coupling and the fuelpump.
Water or sediment accumulated in
the filter can cause loss of power or
hard starting. To prevent engine
malfunction, inspect the filter and
replace when necessary.
:.:- - - -
FUEL HOSE CONNECTOR
Gasoline is highly flammable
and explosive.
You can be burned or seriously
injured when handling fuel.
Stop the engine and keep heat,
sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.
1. Remove the engine coverand
disconnect the fuel hose connector
from the outboard motor.
73
SERVICING YOUR OUTBOARD MOTOR
FUEL FILTER
----7\
SPRING RETAINER
2. Pull the springretainer toward you,
and raise the fuel filter.
3. Check the fuel filterfor water
accumulation or sediment. If no
water or sediment are found,
reinstall the fuel filter properly.
FUEL FILTER
FUEL HOSE CLAMPS
-y--7
FUEL HOSES
4.Remove the fuel filter.
Before removing the fael filter, to
prevent fuel leakage, place fuel
hose clamps on the fuel hoses at
the each side of the fuelfilter.
-----I
ARROW (Fuel Flow Direction)
5. Install the new fuel filterso the
arrow on the fuel filterpoints
toward the fuel pump.
Fuel flow will be reduced if the
fuel filteris installed backward.
6 . Connect the fuelhoses to the fuel
filter securely with the hoseclips.
Remove the fuel hose clamps
used
to closethe fuel hoses.
74
SERVICING YOUR OUTBOARD MOTOR
7. Securely connect the fuel hose
connector to the outboard motor
(refer to page 38 ).
Portable Fuel Tank and Filter
Cleaning
(optional equipment)
8. Prime the engine using the priming
bulb (refer to page 39 ). Check for
fuel leaks.
Repair any fuel leaks if necessary.
Fuel Tank
If loss of power or hard starting are
found to be caused by excessive
water or sediment accumulation in
the fuel filter,inspect the fuel tank.
Fuel Tank Filter
TANK FILTER JOINT
'FILTER
1. Unscrew the fuelhose connector
by turning it counterclockwise,
then remove the fuelhose
connector and fuel filter fromthe
tank.
Clean the fuel tank and tank filterif
necessary. It may be necessary to
drain the fueltank completely and
refill with fresh gasoline.
Empty the portable fuel tank into an
approved gasoline container. Use a
funnel to avoid spilling fuel. Rinse
the fueltank with nonflammable
solvent to remove any accumulated
sediment.
2. Clean the filter in nonflammable
solvent. Inspect the fuel tank filter
and the connector O-ring. Replace
them if damaged.
3. Reinstall the filter and hose
connector in the fuel tank. Tighten
the hoseconnector securely.
75
SERVICING YOUR OUTBOARD MOTOR
Anode Replacement
Painting or coating the anodeswill
defeat their purposeand will lead to
rust and corrosion damage to the
outboard motor. The anodes mustbe
exposed to the water in orderto
protect the outboard motor.
v
(each side)
The anodes are located on each side
of the gearcase. They are made of a
sacrificial material that helps to
protect the outboard motor from
corrosion.
Replace the anodeswhen they have
been reduced to about half their
original size, or if they are crumbling.
76
SERVICING YOUR OUTBOARD MOTOR
Propeller Replacement
Installation
Before replacing the propeller,
remove the clip from the engine stop
switch to prevent any possibility of
the enginebeing started while you
are working with the propeller.
1. Apply marine-grade grease to the
propeller shaft and beveled surface
of the thrust washer.
2. Install the propeller in the reverse
order of removal.
I NOTICE I
Install the thrust washer with the
grooved side toward the gear case.
Use agenuine Honda cotter pin
and bend the pin ends asshown.
The propeller blades may have sharp
edges, so wear heavy gloves to
protect your hands.
Removal
1. Remove the cotter pin, unscrew
the castle nut, remove the
washer,
then remove the propeller and
thrust washer.
PLAIN WASHER
2. Inspect the propeller shaft for any
fishing line ordebris.
'COTTER PIN
CASTLE NUT
THRUST WASHER
\
PROPELLER
77
STORAGE
STORAGE PREPARATION
Cleaning
Proper storagepreparation is
essential for keeping your outboard
motor troublefree and looking good.
The following steps will help to keep
rust and corrosion from impairing
your outboard motor’s function and
appearance, and will make the engine
easier tostart when you use the
outboard motor again.
Wash the outsideof the outboard
motor with clean, freshwater, and
flush the cooling system as described
on p. 31.
Cleaning and Flushing
Thoroughly clean and flush the
outboard motor with fresh water after
operation in dirty water or salt water.
Touch up any damaged paint, and
coat areas that may rust with a light
film of oil. Lubricate controls with a
silicone spray lubricant.
78
FLUSH PORT CAP
Flushing Withthe Honda
Garden Hose Adapter(optional
equipment)
When using the Honda garden hose
adapter (optional equipment), do not
to run the engine during the flushing
procedure.
For safety, remove the emergency
stop switch clip so the engine cannot
be started while you are standing near
the propeller.
1. Remove the flushport cap.
STORAGE
GARDEN HOSEADAPTER
2. Screw the garden hose adapter into
the flushing connector.
3. Attach a garden hose from a fresh
water faucet to the garden hose
adapter.
4.Turn on the fresh water supply and
flush theoutboard motor for at
least 10 minutes.
5. After flushing, remove the garden
hose adapter, and install the flush
port cap.
79
STORAGE
Fuel
Gasoline will oxidize and deteriorate
in storage. Old gasoline will cause
hard starting, and it leaves gum
deposits that clog the fuel system. If
the gasolinein your fuel tank and
vapor separetor deteriorates during
storage, you may need to have the
vapor separetor and other fuel system
components serviced or replaced.
The length of time that gasoline can
be left inyour fuel tank and vapor
separetor without causing functional
problems will vary with such factors
as gasoline blend, your storage
temperatures, and whether the fuel
tank ispartially or completely filled.
The air in a partially filled fuel tank
promotes fuel deterioration. Very
warm storage temperatures accelerate
fuel deterioration. Fuel deterioration
problems may occur within a few
months, or evenless if the gasoline
was not fresh when you filled the
fuel tank.
80
The Distributor’s Limited Warranty
does not cover fuel system damage
or engineperformance problems
resulting from neglected storage
preparation.
You can avoid fuel deterioration
problems by draining the fueltank
and vapor separetor.
VAPOR SEPARATOR
DRAIN BOLT
\
3 . Tilt up the outboard motor.
Gasoline is highly flammable
and explosive.
You can be burned or seriously
injured when handling fuel.
Stop the engine and keep
heat,
sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.
DRAIN HOSE
1. Remove the drain hose from the
silencer case.
2. Connect thedrain hose to the drain
joint of the vapor separator and set
the other end of the hose toward
the outside of the engine undercase.
STORAGE
~~
4. Loosen the vapor separator drain
bolt and drain the vapor separator.
5 . After draining thoroughly, tighten
the drain bolt securely.
6. Install the drain hose to the
silencer case.
7. Drain the fueltank into an
approved gasoline container, or If
you need to store fuelin the fuel
tank, you can extend fuel storage
life by filling the fuel tank with
fresh gasoline and adding a fuel
stabilizer that is formulated for
that purpose.
If using the portable fuel tank
(optional equipment), firmly close
the fuel tank vent knob.
Engine Oil
HOISTING THE OUTBOARD
MOTOR
1. Change theengine oil and the oil
filter (p. 64 - 65 ).
2. Remove the spark plugs (p. 69 ),
and remove the clip from the
emergency stop switch.
3. Pour a tablespoon (5 - 10 cm3)of
clean engine oil into each cylinder.
4. Rotate the engine a few
revolutions to distribute the oil in
the cylinders.
5. Reinstall the spark plugs (p. 70 ).
ENGINE COVER
LOCK LEVER
SIDE
+
I
,ENGINE COVER
1. Unlock and remove the engine
cover.
81
STORAGE
STORAGE PRECAUTIONS
Select a well-ventilated storage area.
If possible, avoid storage areas with
high humidity.
2. Attach the hoist hook to the lifting
eye.
3. Disconnect the outboard motor
from the boat, hoist the outboard
motor, and moveit to the storage
area.
4.After the outboard motor isplaced
in storage and disconnectedfrom
the hoist, install the engine cover.
82
If storing a container of gasoline,
such asthe portable fuel tank
(optional equipment), store it away
from any appliance that operates with
a flame, suchas a furnace, water
heater, or clothes dryer. Also avoid
any area with a sparkproducing
electric motor, or where powertools
are operated.
OUTBOARD MOTOR STAND
If the outboard motorwill be
removed from the boat for storage,
we recommend storing it vertically
by mounting it on a stand.
STORAGE
Cover theoutboard motor to keep out
dust. Do not use sheet plastic as a
dust cover.A nonporous cover will
trap moisture, promoting rust and
corrosion.
REMOVAL FROM STORAGE
Check your outboard motor as
described in the BEFORE
OPERATION chapter of this manual.
If the cylinders were coated with oil
during storagepreparation, the
engine may smoke briefly at startup.
This is normal.
PROTECTOR
If it is necessary to store the outboard
motor horizontally, drain the vapor
separator (p. 80 ), and drain the
engine oil (p. 63 ), before removing
the outboard motor from theboat.
Rest the motor on and cushion of
protective packing material.
83
TRANSPORTING
WITH OUTBOARD MOTOR
INSTALLED ON BOAT
WITH OUTBOARD MOTOR
REMOVED FROM BOAT
When trailering a boat with the
outboard motor attached, leave the
engine in the normal running position,
if possible.
Secure the outboard motor in either
the vertical or horizontal position
shown on p. 82 - 83 .
Use a motor support bar to prevent
the outboard motor from moving
while trailering the boat. Refer to the
manufacturer’s instructions for using
a motorsupport bar.
MOTOR SUPPORTBAR
(commercially available)
84
TAKING CARE OF UNEXPECTED PROBLEMS
ELECTRIC STARTERWILL
NOT OPERATE
Possible Cause
Correction
Battery connections loose or
corroded.
Clean andtighten battery
connections.
Battery discharged.
Recharge battery.
2. Check fuses.
Fuse(s) burnt out.
Replace fuse(s) (p. 90).
3. Use starting procedure (p. 39 ),
then take outboard motor toan
authorized Honda Marinedealer,
or referto the shop manual.
Starter malfunction, switch
malfunction, or electrical problem
in the starting circuit.
Replace orrepair faulty
components asnecessary.
1. Check battery.
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT START
Possible Cause
Correction
1. Check emergency stop switch
clip.
Clip not inserted in stop switch.
Insert clip in stop switch.
2. Check control positions.
Control lever not in neutral
position.
Shift toneutral.
Fast idle lever raised (side-mount
tYpe).
Leave fast idlelever OFF (p. 18).
86
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT START
(continued)
3 . Check fuel.
4. Remove and inspect spark plugs.
5. Take outboard motor to an
authorized Honda Marine dealer,
or refer to the shopmanual.
Possible Cause
Correction
Out of fuel.
Refuel (p. 71 ).
Fuel vent closed (portable fuel
tank).
Open fuel tank vent (p. 32 ).
Fuel hose not primed.
Squeeze priming bulb (p. 33 ).
Fuel pump filteror fuel tank filter
clogged.
Replace fuel filters (p. 73 ).
Bad fuel; boat stored without
treating or draining gasoline, or
refueled with bad gasoline.
Drain fuel tank and vapor
separator (p. 80 ). Refill with fresh
gasoline (p. 71 ).
Spark plugs faulty, fouled or
improperly gapped.
Clean, gap orreplace spark plugs
(P. 69 >.
Spark plugs wet with fuel (flooded
engine).
Dry and reinstall spark plugs. Start
engine with the throttle open.
Fuel system malfunction, fuel
pump failure, ignition malfunction,
stuck valves, etc.
Replace or repair faulty
components as necessary.
87
TAKING CARE OF UNEXPECTED PROBLEMS
1
HARD STARTING OR STALLS
AFTER
STARTING
Possible Cause
Correction
1. Check control positions.
Fast idle lever raised (side-mount
type).
Leave fast idlelever OFF (p. 18 ).
2. Check fuel.
Fuel vent closed (portable fuel
tank).
Open fuel tank vent (p. 32 ).
Fuel hosenot primed.
Fuel pumpfilter or fueltank
clogged.
Squeeze priming bulb(p. 33 ).
Replace fuel filters(p. 73 ).
Bad fuel; boat stored without
treating or draining gasoline, or
refueled with bad fuel.
Drain fuel tank and vapor
separator (p. 80 ). Refill with fresh
gasoline (p. 71 ).
88
TAKING CAREOF UNEXPECTED PROBLEMS
HARD STARTING OR STALLS
AFTER STARTING
(continued)
Correction
Possible Cause
I
3. Remove andinspect spark plugs.
Spark plugs faulty, fouled or
improperly gapped.
4. Take outboard motor to an
authorized Honda Marine dealer,
or refer to the shop manual.
Fuel system malfunction, fuel
pump failure, ignition malfunction,
etc.
ENGINE OVERHEATS
Possible Cause
1
Clean, gap orreplace spark plugs
(P. 69 1.
I
Replace or repair faulty
components as necessary.
Correction
1. Check water intake screens.
Water intake screens clogged.
Clean water intake screens.
2. Take outboard motor to an
authorized Honda Marine dealer,
or referto the shop manual.
Faulty thermostat or water pump.
Replace or repair faulty
components as necessary.
89
TAKING CARE OF UNEXPECTED PROBLEMS
BATTERY WILL NOT
CHARGE ANDELECTRIC
STARTER WILL NOT
OPERATE
The battery-charging (ACG) circuit
and the electric starter relay circuit
are protected by the 10,30-ampere
main fuses and90-ampere ACG fuse.
If the fuseburns out, the enginewill
not chargethe battery, and the
electric starter will not operate.
The ignition switch is protected by
the 10-ampere main fuse. If the fuse
bums out, the enginewill not start or
run, and the power tridtilt switch
will not oprate.
Fuse Replacement
Main Fuse
FUSE (lOA, 30A)
1. With the engine stopped,remove
the enginecover.
2. Remove the fusecovers.
3. Remove and inspect the fuses. If a
fuse is burnt out, install a
replacement fuse of the specified
rating. The outboard motor is
supplied with spare fuses in the
fuse holders.
SPARE FUSE (lOA, 30A)
4.Reinstall the fuse covers and the
engine cover.
MAIN FUSES: 10 A, 30 A
Never use a fuse with a rating
greater than specified. Serious
damage to the electrical system
could result.
90
FUSE COVER
Before further operation,try to
determine and correct theelectrical
problem that caused the fuse to
bum out. An uncorrected electrical
problem may cause the fuse to
burn out again.
TAKINGCARE OF UNEXPECTEDPROBLEMS
3. Remove thefuse case lid.
ACG Fuse
FUSE CASE LID
“90A”MARK
4. Remove the old fuseby removing
two 5 mm screws.
5. Install a new fuse with the “90 A”
mark downward.
A spare fuseis located on the reverse
side of the fuse case lid and tightened
with two 3 mm screws.
When the new fuse is set as a spare
fuse on the reverse side of the fuse
case lid, set thefuse so that you can
see the ‘‘90 A” mark on it.
ACG FUSE: 90 A
I
FUSE
SPARE
FUSE (90A)
1Disconnect the battery cable at
the battery negative (-) terminal
before replacing the f use.
Failure to do so may cause A
short circuit.
6. After finishing replacement, install
the fuse case lid with its hook
toward the engine side.
7. Be sure to check the fuse case lid
is securely locked.
Replacement
1 . Stop the engine.
2. Remove the engine cover.
91
1
TAKING CARE OF UNEXPECTED PROBLEMS
OIL PRESSURE INDICATOR
LIGHT GOES OFF AND
ENGINE SPEED IS LIMITED
Panel-Mount/Top-Mount Types
Side-Mount Type
If the throttle is closed suddenly after
full throttle operation, engine speed
may drop below the specified idle
rpm, andthat could activate the
engine protection system
momentarily.
If low oil pressure activates the
engine protection system, stop the
engine, check the engine oil level (p.
63 ), and add oil if needed.
If oil pressure becomes low,the
green indicator light will go off, and
the engine protection system will
limit engine speed. If you are at
cruising speed, engine speed will
decrease gradually.
Oil pressure indicator is also
equipped with a buzzer that sounds
when the green indicator light goes
off.
Low oil pressure may be the result of
low engineoil level is, or there may
be a problem with the engine
lubrication system.
92
With the engine oil at the
recommended level, restart the
engine. If the lubrication system is
OK, the green indicator light should
come on within 30 seconds, and the
engine will respond normally to
throttle control lever operation.
If the engine protection system
remains activated after 30 seconds,
return to the nearest boat landing, and
have the outboard motorinspected by
an authorized Honda marinedealer.
TAKING CARE OF UNEXPECTED PROBLEMS
OVERHEATING INDICATOR
LIGHT COMES ON AND
ENGINE SPEED IS LIMITED
Side-Mount Type
If the engine overheats, the red
indicator light will come on, and the
engine protection system will limit
engine speed. If you are at cruising
speed, engine speed will decrease
gradually.
I
Remote-control types are equipped
with a buzzer that sounds when the
red indicator light comes on.
Engine overheating may be the result
of clogged water intake screens, or
there may be a problem with the
cooling system thermostat or water
pump.
Panel-Mount/Top-Mount Types
If the engineis stopped after running
at full throttle, and then restarted
soon afterward, that could activate
the engine protection system
momentarily.
COOLING SYSTEM INDICATOR
If overheating activates the engine
protection system, idle the engine in
neutral, and check the cooling system
indicator.
If water is flowing fromthe cooling
system indicator, continue idling for
30 seconds. If the cooling system is
OK, the red indicator light should go
off within 30 seconds, and the engine
will respond normally to throttle
control lever operation.
93
TAKING CARE OF UNEXPECTED PROBLEMS
If there is no water flowing from the
cooling system indicator, stop the
engine, and tilt the outboard motorto
inspect the water intake screens. If
clogged, clean the water intake
screens, return the outboard motorto
the running position, restart the
engine, and checkthe cooling system
indicator again.
If there is still no water flowingfrom
the cooling system indicator, or if the
engine protection system remains
activated after 30 seconds, return to
the nearest boat landing, and havethe
outboard motorinspected by an
authorized Honda marinedealer.
SUBMERGED MOTOR
A submerged outboard motor must
be serviced immediately afterit is
recovered from the water in order to
minimize corrosion.
If there is a Honda marinedearship
nearby, take the motor to the dealer
immediately. If you are far from a
dealership, proceed as follows:
1. Remove the engine cover, and
rinse the outboard motor with
fresh waterto remove salt water,
sand, mud, etc.
2. Drain the vapor separator as
described on p. 80.
3. Change the engine oil and oil filter
as described on p. 63 - 65 . If
there was waterin the engine
crankcase, or if the used engine oil
showed signs of water
contamination, then a second
engine oil change should be
performed after runningthe engine
for half an hour.
4.Remove the spark plugs (p. 69 ).
Operate the starter to expel1 water
from the engine’s cylinder.
5. Put a teaspoonof engine oil into
each spark plug hole to lubricate
the inside of the cylinders.
Reinstall the spark plugs.
If the engine was running when
it
submerged, there may be
mechanical damage, suchas bent
connecting rods. If the engine
binds when cranked, do not
attempt to run the engine until it
has been repaired.
94
TAKING CARE OF UNEXPECTED PROBLEMS
6. Attempt to start the engine (be sure
the water level is at least 2 inches
above the antiventilation plate).
[NOTlCEI
Running the outboard motor without
sufficient cooling water will damage
the water pump and overheat the
engine.
If the engine fails to start, remove
the spark plugs, clean and dry
them, then reinstall the spark plugs
and attempt to start the engine
again.
If the engine starts, and no
mechanical damage isevident,
continue to run the engine for a
half hour or longer. Be sure the
water level is at least two inches
above theantiventilation plate to
avoid overheating and water pump
damage.
7. As soon as possible, take the
outboard motorto an authorized
Honda Marinedealer for
inspection and service.
95
1
TECHNICAL AND CONSUMERINFORMATION
TECHNICAL INFORMATION
LEFT STERN BRACKET
Serial Number Locations
Record the product identification
number and engineserial numbers in
the space provided onthis page. You
will need these numbers when
ordering parts, and when making
technical or warrantyinquiries (p.
105 ).
PRODUCT IDENTIFICATION NUMBER
96
ENGINE SERIAL NUMBER
The product identification number is
stamped ona plate attached on the
left stern bracket.
The engineserial number is
stamped onthe cylinder head on
the back of the engine.
Product identification number:
Engine serial number:
Oxygenated Fuels
Some conventional gasolines are
being blended with alcohol or an
ether compound. These gasolines are
cdllectively referred to as oxygenated
fuels. To meet clean air standards,
some areas of the United States and
Canada use oxygenated fuels to help
reduce emissions.
If you use an oxygenated fuel, be
sure it is unleaded and meets the
minimum octane rating requirement.
Before using an oxygenated fuel, try
to confirm the fuel’scontents. Some
states/provinces require this
information to be posted on the pump.
The following arethe EPA-approved
percentages of oxygenates:
damage metal, rubber, and plastic
parts of your fuel system.
ETHANOL: ethyl or grain alcohol;
10% by volume.
If you notice any undesirable
operating symptoms, try another
service station, or switch to another
brand of gasoline.
You may use gasoline containing up
to 10% ethanol by volume. Gasoline
containing ethanol may be marketed
under the name ‘‘Gasohol”.
MTBE: Methyl Tertiary Butyl Ether;
15%by volume.
Fuel system damage or performance
problems resulting from theuse of an
oxygenated fuel containing more
than the percentages of oxygenates
mentioned above arenot covered
under warranty.
You may use gasoline containing up
to 15% MTBE by volume.
METHANOL: methyl or wood
alcohol; 5% by volume.
You may use gasoline containing up
to 5 % methanol by volume, as long
as it also contains cosolvents and
corrosion inhibitors to protect the
fuel system. Gasoline containing
more than 5% methanol by volume
may cause starting and/or
performance problems. It may also
97
I
TECHNICAL AND CONSUMER INFORMATION
Emission
Control
System
Information
Source of Emissions
The combustionprocess produces
carbon monoxide,oxides of nitrogen,
and hydrocarbons. Controlof
hydrocarbons andoxides of nitrogen
is very important because, under
certain conditions, they react to form
photochemical smog whensubjected
to sunlight. Carbon monoxide does
not react in the same way,but it is
toxic.
Honda utilizes lean carburetor
settings and other systems to reduce
the emissions of carbon monoxide,
oxides of nitrogen, and hydrocarbons.
98
The US.and California Clean
Air Act
EPA andCalifornia regulations
require all manufacturers tofurnish
written instructions describing the
operation and maintenanceof
emission control systems.
Tampering and Altering
Tampering with or altering the
emission control system may increase
emissions beyondthe legal limit.
Among those acts that constitute
tampering are:
0
The followinginstructions and
procedures must be followedin order
to keep the emissions from your
Honda enginewithin the emission
standards.
Removal or alteration of any part
of the intake, fuel, orexhaust
systems.
Alterations that would causethe
engine tooperate outside its design
parameters.
TECHNICAL AND CONSUMER INFORMATION
Problems That MayAffect
Emissions
If you are aware of any of the
following symptoms, have your
engine inspected and repaired by
your servicing dealer.
Hard starting or stalling after
starting.
Rough idle.
0
Misfiring orbackfiring under load.
0
Afterburning (backfiring).
Black exhaust smoke orhigh fuel
consumption.
Replacement Parts
The emission control systems on
your Honda enginewere designed,
built, and certified to conform with
EPA and Californiaemission
regulations. We recommend the use
of genuine Hondaparts whenever
you have maintenance done. These
original-design replacement parts are
manufactured to the same standards
as the original parts, so you can be
confident of their performance. The
use of replacement parts that are not
of the original design and quality
may impair the effectivenessof your
emission control system.
A manufacturer of an aftermarket
part assumes the responsibility that
the part will not adversely affect
emission performance. The
manufacturer or rebuilder of the part
must certify that use of the part will
not result in a failure of the engine to
comply with emission regulations.
Maintenance
Follow the maintenance schedule on
p. 5 8 . Remember that this schedule
is based on the assumption that your
machine will be used for its designed
purpose. Sustained high-load
operation, or use in unusual
conditions, will require more
frequent service.
99
'
~
TECHNICAL
AND
CONSUMER
INFORMATION
Star Label
A Star label was applied to this
outboard motorin accordance with
the requirements of the California
Air Resources Board.
The Star Label means Cleaner Marine Engine
This enginehas been certified as a:
0
I
IXI
The Symbol for Cleaner Marine Engines:
Cleaner Air andWater - for healthier lifestyle and environment.
Better Fuel Economy - bums up to 30 - 40 percent less gas and oil than
conventional carbureted two-stroke engines, saving money and resources.
Longer Emission Warranty - protects consumer for wony free operation.
100
TECHNICAL AND CONSUMER INFORMATION
One Star
Low Emission
Two Stars
Very Low Emission
Three Stars
Ultra Low Emission
The one-star label identifies engines
that meet the Air Resources Board’s
2001 exhaust emission standards.
Engines meetingthese standards
have 75% lower emissions than
conventional carbureted two-stroke
engines. These engines are equivalent
to the U.S. EPA’s 2006 standards for
marine engines.
The two-star label identifies engines
that meet the Air Resources Board’s
2004 exhaust emissionstandards.
Engines meetingthese standards
have 20% lower emissions than One
Star-Low-Emission engines.
The three-star label identifies engines
that meet the Air Resources Board’s
2008 exhaust emission standards.
Engines meetingthese standards
have 65% loweremissions than One
Star-Low-Emission engines.
Cleaner Watercraft - Get the Facts
1-8OO-END-SMOG
www.arb.ca.gov
101
TECHNICAL AND CONSUMER INFORMATION
Specifications
SAE 1OW-30
Gear case:API standard (GL-4/5) SAE
Honda outboards are power rated in accordance with NMMA produce andusing the ICOMIA standard28/23.
102
TECHNICAL AND CONSUMER INFORMATION
Specifications
Starter system
Ignition system
Lubrication system
Specified oil
Oil capacity
Fuel pump
Fuel
Gear change
Steering, angle
Transom angle
Electric starter
Fully transistorized, battery ignition
Trochoid pump pressure lubrication
Engine: API standard (SG, SH)
SAE 1OW-30
Gear case:API standard (GL-4/5)
SAE
90 outboard motor gear oil
Engine: 5.9 US qt (5.6 Q ,4.9 Impqt)
Gear case: 1.00 US qt (0.95 Q ,0.84 Imp
ZFR7F (NGK)
Diaphragm type
Automotive unleaded gasoline
(86 pumpoctane or higher)
Forward-Neutral-Reverse (dog type)
30" right and left
5 stages (8", 12O, 16", 20°, 24")
Honda outboards are power rated in accordance with NMMA produce and using the ICOMIA standard 28/23.
103
TECHNICAL AND CONSUMER INFORMATION
BF115A C? BF130A Tune up
Spark plug gap
Idle speed
Valve clearance (cold)
Other specifications
104
0.028-0.031 in (0.70-0.80 r n r n )
See page 69
750 50 rpm
See shop manual
Intake:
0.26
0.02 rnrn
See shop manual
Exhaust: 0.30 -t 0.02 mrn
No other adiustrnents needed.
*
*
TECHNICAL AND CONSUMER INFORMATION
CONSUMER INFORMATION
Warranty Service Information
Or telephone: (770) 497-6400
Honda Publications
Honda Marine dealership personnel
are trained professionals. They
should be able to answer any
question you may have. If you
encounter aproblem that your dealer
does not solve to your satisfaction,
please discuss it with the dealership’s
management. The Service Manager
or General Manager can help. Almost
all problems are solved in this way.
When you write or call, please give
us this information:
These publications will give you
additional information for
maintaining and repairing your
outboard motor. You may order them
from your Honda marine dealer.
Shop Manual
This manual covers complete
maintenance and overhaul procedures.
It is intended to be used by a skilled
technician.
Parts Catalog
This manual provides complete,
illustrated parts lists.
If you are dissatisfied with the
decision made by the dealership’s
management, contact the Honda
Marine Customer Relations Office.
You can write:
American Honda Motor Co., Inc.
Marine Division
Customer Relations Office
4900 Marconi Drive
Alpharetta, Georgia 30005-8847
Model and serial numbers (p. 96 )
Name of the dealer who sold the
outboard motor to you
Name and address of the dealer
who services your outboard motor
Date of purchase
Your name, address, and telephone
number
A detailed description of the
problem
105
INDEX
Alternator (ACG) Indicator
............................................
29
Anodes ............................................................................
32
Replacement ...............................................................
ARE YOU READYTOGET UNDER WAY ? .......... 34
BATTERY WILL NOT CHARGE AND
...... 90
ELECTRIC STARTER WILL NOT OPERATE
BEFORE OPERATION................................................. 34
BREAK-IN PROCEDURE............................................ 36
Common Controls.......................................................... 26
COMPONENT AND CONTROL LOCATIONS......... 11
CONSUMER INFORMATION..................................
105
CONTROLS...................................................................
15
CONTROLS AND FEATURE IDENTIFICATION
CODES ....................................................................... 10
10
CONTROLS AND FEATURES ...................................
Cooling System Indicator
............................................... 3 1
CRUISING ..................................................................... 5 1
106
Emission Control System Information..........................
Engine
76
Cover
Lock Levers............................................................
Lock Lever Adjustment.........................................
............................
Lock Lever Bracket Adjustment
REMOVAL AND INSTALLATION....................
Oil
Change....................................................................
Filter Change..........................................................
Level Check ...........................................................
Recommendations ..................................................
98
27
62
62
61
63
64
63
66
INDEX
Fast Idle Lever................................................................
Fuel
Cap Vent Knob (optional equipment)........................
HOSE CONNECTIONS............................................
.......................................
Gauge (optional equipment)
PRIMING ...................................................................
Priming Bulb ..............................................................
RECOMMENDATIONS...........................................
Pump Filter Inspection and Replacement ..................
18
32
38
29
39
33
72
73
Gear OilLevel Check .....................................................
68
GearshifdTrottle Control Lever
Panel-Mount Type...................................................... 20
Side-Mount Type ....................................................... 16
Top-Mount Type........................................................ 23
GEARSHIFTING AND THROTTLE OPERATION... 48
Panel-Mount Type...................................................... 49
Side-Mount Type....................................................... 48
Top-Mount Type........................................................ 49
HOISTING THE OUTBOARDMOTOR .....................
Ignition Switch
Panel-Mount Type......................................................
Side-Mount Type .......................................................
Top-Mount Type........................................................
.....................
IMPORTANT SAFETY INFORMATION
INDICATORS................................................................
INSTRUMENTS ............................................................
IS YOUR OUTBOARD MOTOR
READY TO GO ? .....................................................
18
15
22
7
29
28
34
Lubrication Points..........................................................
68
MAINTENANCE SAFETY..........................................
MAINTENANCE SCHEDULE....................................
MOORING. BEACHING. LAUNCHING ....................
56
58
53
81
107
I
INDEX
Oil Pressue Indicator...................................................... 30
OIL PRESSURE INDICATOR LIGHT GOES
............... 92
OFF AND ENGINE SPEED IS LIMITED
OPERATION ................................................................. 36
OTHER FEATURES.....................................................
3 1
OUTBOARD MOTOR SAFETY
.................................... 7
Overheating Indicator..................................................... 30
OVERHEATING INDICATOR LIGHT COMES
ON AND ENGINE SPEED IS LIMITED
................. 93
Overrev Limiter.............................................................. 3 1
Oxygenated Fuels........................................................... 97
PORTABLE FUEL TANK
32, 38
(optionnal equipment)..........................................
Portable Fuel Tank andFilter Cleaning
(optionnal equipment)................................................
75
........................................................... 26
Power Tilt Switch
Power TridTilt Switch ................................................. 25
Programmed Fuel Injection (PGM-FI) Indicator
........... 29
Propeller Replacement................................................... 77
REFUELING..................................................................
REMOVAL FROM STORAGE....................................
108
71
83
SAFE OPERATING PRECAUTIONS.........................
36
SAFETY LABEL LOCATIONS
..................................... 9
96
Serial Number Locations................................................
............... 55
SERVICING YOUR OUTBOARD MOTOR
SHALLOW WATER OPERATIONS
........................... 53
Spark Plug Service......................................................... 69
102
Specifications...............................................................
Star Label .....................................................................
100
STARTING THE ENGINE...........................................
39
Panel-Mount Type......................................................
42
Side-Mount Type....................................................... 39
Top-Mount Type........................................................ 44
50
STEERING.....................................................................
STOPPING THE ENGINE
............................................ 46
...................................... 46
Emergency Engine Stopping
Normal Engine Stopping
............................................ 47
78
STORAGE .....................................................................
STORAGE PRECAUTIONS......................................... 82
STORAGE PREPARATION......................................... 78
78
Cleaning and Flushing ................................................
Engine oil ...................................................................
81
Fuel .............................................................................
80
94
SUBMERGED MOTOR................................................
Switch Clip and Emergency Stop Switch
Panel-Mount Type...................................................... 19
Side-Mount Type....................................................... 16
Top-Mount Type........................................................ 22
INDEX
Tachometer (optional equipment) ..................................
28
TAKING CAREOF UNEXPECTED PROBLEMS..... 85
TECHNICAL AND CONSUMER INFORMATION
... 96
96
TECHNICAL INFORMATION....................................
THE IMPORTANCEOF MAINTENANCE ................ 55
Throttle Button
Panel-Mount Type...................................................... 20
Top-Mount Type........................................................ 23
Tilt Lock Lever............................................................... 26
TOOL KIT(optional equipment)................................... 57
TRANSOM ANGLE ADJUSTMENT..........................
37
...................................... 27
Transom Angle Adjusting Rod
TRANSPORTING .........................................................
84
WITH OUTBOARD MOTOR INSTALLED
ON BOAT .............................................................. 84
WITH OUTBOARD MOTOR REMOVED
FROM BOAT ........................................................ 84
28
Trim Meter (optional equipment) ..................................
Trim Tab.........................................................................
28
60
TRIM TAB ADJUSTMENT.........................................
WIRING DIAGRAMS.........................
Inside Back Cover
109
I"'
I
I
444=
Ia
t
L
3
0
-0
2%
r
I
L
q,
I
1
I
i
OEOS-SMZ- 1EX00
EOSSMZ LE