T OA SEC U R I T Y S Y S T E M S V I DEO /A U DI O/NETWORK PRODUCTS Contents I FI REG ST RM Product Lineup .......................................................................................................................... 1 Combination Dome Camera System ........................................................................................ 4 Combination Dome Camera ................................................................................................... 5 Brackets and Dome Cover ..................................................................................................... 7 Setting Guide ......................................................................................................................... 8 Remote Controller ................................................................................................................... 9 Interface Unit ........................................................................................................................ 10 Alarm Unit ............................................................................................................................ 10 Features ............................................................................................................................... 11 System Examples ................................................................................................................. 13 Network Camera System ......................................................................................................... 14 Network Camera .................................................................................................................. 15 Network Video Transmitter ................................................................................................... 17 1-Channel Software Decoder ............................................................................................... 18 4-Channel Software Decoder ............................................................................................... 19 System Examples ................................................................................................................. 21 Wide Dynamic Range Color Cameras .................................................................................... 22 Wide Dynamic Range Color Camera .................................................................................... 23 Futures ................................................................................................................................. 25 Setup for Camera ................................................................................................................. 27 Compact Color Cameras ......................................................................................................... 28 Color Camera ....................................................................................................................... 29 Color Dome Camera ............................................................................................................. 31 Outdoor Color Camera ......................................................................................................... 32 Lens Selection Guide .............................................................................................................. 33 Lenses ..................................................................................................................................... 34 Motorized Zoom Lenses (DC-input type) .............................................................................. 35 Manual Zoom and Varifocal Auto Iris Lenses (DC-input type) .............................................. 36 Auto Iris Aspherical Lenses (DC-input type) ......................................................................... 37 Auto Iris Lenes (DC-input type) ............................................................................................ 38 Manual Iris lenses ................................................................................................................. 39 Housings/Pan & Tilt Heads/Mounting Brackets .................................................................... 40 Selection Chart ..................................................................................................................... 41 Camera Housings ................................................................................................................ 43 Pan & Tilt Heads ................................................................................................................... 45 Housing Mounting Brackets ................................................................................................. 46 Pan & Tilt Head Mounting Brackets ...................................................................................... 48 Camera Mounting Brackets ................................................................................................. 49 Zoom Lens Mounting Bracket .............................................................................................. 50 Pan Head Controller ............................................................................................................. 50 Remote Control Units ........................................................................................................... 51 Camera Selector .................................................................................................................. 55 Housing Selection Chart ....................................................................................................... 56 Pan & Tilt Head Selection Chart ........................................................................................... 56 Multiplexer/Switcher ................................................................................................................ 58 16-Channel Duplex Multiplexer ............................................................................................ 59 9-Channel Duplex Multiplexer .............................................................................................. 61 Features ............................................................................................................................... 63 Setup Screen ........................................................................................................................ 67 Quad Screen Splitter ............................................................................................................ 68 Manual Switchers ................................................................................................................. 69 Associated Equipment ............................................................................................................ 70 Video Distributor ................................................................................................................... 71 Cable Compensator ............................................................................................................. 72 Video Signal Adaptor ........................................................................................................... 73 Coaxial Multi-Transmission Unit ............................................................................................ 74 Voice Security Intercom System ............................................................................................ 76 Network Audio Adapter ........................................................................................................... 88 Accessories ............................................................................................................................. 90 Metal Rack-Mount Selection Chart ......................................................................................... 91 Index ..................................................................................................................................... 92 ERED Certificate No. 21896 * TOA has been granted the “ISO 9001 (BS 5750)” registration in the 9000 Series of Quality Assurance Standards by the International Organization for Standardization (ISO). Dedicated to security and safety. TOA's accumulated experience and know-how in audio and video date all the way back to 1934 for audio and 1983 for CCTV. It all comes together with sophisticated network technologies to offer innovative monitoring and surveillance solutions for any environment, for systems that range from basic to extremely sophisticated. With an extensive range of cameras, multiplexers and ancillary equipment, TOA enables the end user to configure a system that optimally meets specific requirements. The end result is a high-performance, cost-effective solution that offers TOA's acclaimed total reliability. Today sees an ever-increasing demand for security and safety in a multitude of locations, and as this trend continues to increase, TOA continually refines and perfects its technologies to develop new CCTV, security intercom products and audio products that benefit society. Metal Rack-Mount Selection Chart Accessories Network Audio Adaper Voice Security Intercom System Coaxial Multi-Transmission Unit Assocuate Equipments Multiplexer/ Switcher Camera Housings/Pan & Tilt Heads Mounting Brackets Lenses for CCTV Cameras Compact Color Cameras Wide Dinamic Range Color Camera Network Camera System Combination Camera System PRODUCT LINEUP Color Cameras P 37 Wide Dynamic Range Color Camera Housing Mounting Brackets Pan & Tilt Heads P 45 P 22 CH-0808G P 23 C-CC351A C-CC354A P 47 C-PH200 P 38 (Lens is optional) C-BC100K P 46 Compact Color Cameras CT-0312GA P 29 P 47 CC-5525 P 38 C-BC100T C-CV14-CS (Lens is optional) P 46 CT-0412GA P 30 P 47 CC-5521 P 38 C-BC200H C -CV14 -2 (Lens included) P 46 Compact Color Dome Camera P 31 CT-0812GA Manual iris Lenses Pan & Tilt Head Mounting Bracket CC-5550A P 39 P 48 C-CV24-2 Zoom Lens Mounting Bracket (Lens included) Compact Outdoor Color Camera CT-0312A C-BC200K P 39 P 48 CT-0412A CC -4520 P 39 P 48 P 32 P 50 C-CV44-3 (Lens included) C-BL20 Lenses Motorized Zoom and Varifocal Auto iris Lenses Remote Controllers P 50 P 35 CT-6ZMG CT-10ZMGA CT-0812A Camera Housings CC -4510 CC-5050B Camera Mounting Brackets P 51 P 43 P 35 P 49 C-CH100 C-CH100FH CT-21ZMG CC-5011B P 53 C-BC11 Manual Zoom Lenses P 43 P 44 P 36 P 49 CC-5111B C-CH200 C-CH200FH P 44 CT-2ZMGA C-BC21 Relay Box P 49 P 36 P 53 C-CH210FH CT-10VFG P 44 Auto Iris Lenses C-BC31 P 49 P 37 CH-2610G P 55 C-BC41 P 45 P 49 P 37 CC-6080DMS CC-6080DMB CC-6080DMW WH-4 1 Camera Selector CC-6000A Dome-shaped Camera Housing CH-3808G CC-5120 CC-5131B Video Distributor Multiplexers Accessories Rack Mounting Accessories P 59 P 71 BNC Cable and Plug Blower Unit P 90 C-MS161D C-VD6 CC-P5BB P 61 BU-412 Cable Compensator Cabinet Rack P 72 P 90 C-MS91D CC-01BB Quad Screen Splitter P 68 CC-3331B CR-131N Video Signal Adaptor P 90 CC-05BB P 73 C-QA40 CR-273 CC-3350B Manual Switcher P 69 P 90 CC-4901 24 V AC Power Supply P 51 CR-413 CR-413-6 Blank Panel CC-3011B P 69 CC-3021B P 90 CC-4902 CC-5941B BK-013B (1-size Blank Panel) BK-023B (2-size Blank Panel) BK-033B (3-size Blank Panel) Perforated Panel P 90 CC-4903 PF-013B (1-size Perforated Panel) PF-023B (2-size Perforated Panel) CC-4904 2 Combination Dome Camera System Combination Dome Camera P5 Alarm Unit Interface Unit Network Camera P 14 System Network Cameras C-CC504S C-CC554S C-AL80 C-IF500 Remote Controller Ceiling Mount Bracket N-CC1000 Flush Ceiling Mount Bracket N-CC1110 Network Video Transmitter C-BC501 C-RM500 Ceiling Suspension Bracket C-BC501T Wall Mounting Bracket C-BC501K C-BC501U Smoked Dome Cover Master Station 4-Channel Software Decoder C-A501DM Voice Security Intercom System Main Frame N-V T1010 Full-Duplex Substation N-SD1040 P 76 Network Audio Adapter P 88 RS-190 MS-900 VS-900MF Option Handset NX-100 Substations RS-150 Site Connector VS-900SC Coaxial MultiTransmission Unit RS-180 RS-160 RS-170 RS-191 Direct Select Control Card VS-900DI P 74 Direct Select I/O Card VS-910DI C-AP105 2 units in every set Power Transformer Unit PU-200 Main Frame Wall Mounting Bracket YC-303 3 Rack Mount Panel for PU-200 PN-100B Back Box (2-gang) YC-302 Combination Camera System COMBINATION DOME CAMERA SYSTEMS Combination Dome Cameras C-CC504S standard type C-CC554S multi function type Brackets and Cover C-BC501 Ceiling Mount Bracket C-BC501U C-BC501T Flush Ceiling Mount Bracket Ceiling Suspension Bracket C-BC501K Wall Mounting Bracket C-A501DM Smoked Dome Cover Controller and Units C-IF500 Interface Unit C-RM500 Remote Controller C-AL80 Alarm Unit 4 COMBINATION DOME CAMERA SPECIFICATIONS (PAL) Power source Power consumption Control Video Output Camera Control Terminal Alarm Input Auxiliary Contact Output Sensor Power Supply Synchronization Camera/Position ID No. of Preset Positions Camera Address Camera Image device Resolution S/N ratio Minimum Illumination 24V AC 50/60Hz 10W (normal operation), 25W max. RS-485 communications system VBS 1.0V(p-p) 75Ω RS-485 camera control connector (5 pins, black) 8 channels, no-voltage make contact input, open voltage: 18V DC short-circuit current; Under 2mA, alarm input connector (10 pins, white) 2 channels, open collector output, withstand voltage: 30V DC, permissible current: Under 100mA, expansion connector (5 pins, white) 18V DC, 40mA max., expansion connector (5 pins, white) Internal synchronization/power synchronization (phase adjustable when in power synchronization mode) 8 alphanumeric characters 255 Positions 001 – 999 Camera control connector (5 pins, black) Alarm input connector (10 pins, white) Bullet terminal (male) Expansion connector (5 pins, white) Power cord length approx. 1.7 m BNC-R jack ø224 ø7 46 Composite cable length approx. 50 cm 4 – ø7.2 ø125 ø136 Unit: mm SPECIFICATIONS (NTSC) Power source Power consumption Control Video Output Camera Control Terminal Alarm Input Auxiliary Contact Output Sensor Power Supply Synchronization Camera/Position ID No. of Preset Positions Camera Address Camera Image device Resolution S/N ratio Minimum Illumination 24V AC 50/60Hz 10W (normal operation), 25W max. RS-485 communications system VBS 1.0V(p-p) 75Ω RS-485 camera control connector (5 pins, black) 8 channels, no-voltage make contact input, open voltage: 18V DC short-circuit current; Under 2mA, alarm input connector (10 pins, white) 2 channels, open collector output, withstand voltage: 30V DC, permissible current: Under 100mA, expansion connector (5 pins, white) 18V DC, 40mA max., expansion connector (5 pins, white) Internal synchronization/power synchronization (phase adjustable when in power synchronization mode) 8 alphanumeric characters 255 Positions 001 – 999 1/4 type CCD Horizontal: 480 lines (at center) 50dB High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV) High-sensitivity function 0N: 0.03 lx (350mV), 0.01 lx (140mV) Backlight Compensation WIDE DYNAMIC/ON/OFF Dynamic range 46dB (backlight compensation: WIDE DYNAMIC operation) High-Sensitivity Function B/W mode and slow shutter mode (32 times max.) White Balance ATW/AWB Flicker Reduction Automatic correction Electronic Zooming 10x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 23x Effective Focal Length f = 3.6 – 82.8mm Effective Angle of View Horizontal: 54° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T) Maximum Aperture F 1.6 (W) – F 3.7 (T) Zoom Speed WIDE end to TELE end Approx. 1.6s (preset operation), Approx. 2.9s (manual operation) Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: 0° to 180° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 120°/s max. (manual operation) 1/4 type CCD Horizontal: 480 lines (at center) 50dB High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV) High-sensitivity function 0N: 0.03 lx (350mV), 0.01 lx (140mV) Backlight Compensation WIDE DYNAMIC/ON/OFF Dynamic range 46dB (backlight compensation: WIDE DYNAMIC operation) High-Sensitivity Function B/W mode and slow shutter mode (32 times max.) White Balance ATW/AWB Flicker Reduction Automatic correction Electronic Zooming 10x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 23x Effective Focal Length f = 3.6 – 82.8mm Effective Angle of View Horizontal: 54° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T) Maximum Aperture F 1.6 (W) – F 3.7 (T) Zoom Speed WIDE end to TELE end Approx. 1.6s (preset operation), Approx. 2.9s (manual operation) Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: 0° to 180° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 120°/s max. (manual operation) Other Function Other Function Operating Temperature Operating Humidity Application Waterproof Capability Finish Dimensions Weight Accessory Option Auto-pan, Preset Sequence, Auto-Trace (30s), Auto-Flip, Freeze Preset, Privacy Masking, Refresh Functions –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Under 90% (no due condensation produced) Indoors and under the eaves IP-52 Case/base: Aluminum die-casting, sand gray, paint Dome cover: Acrylic resin (transparent) Camera section external diameter: ø136 × 239 (H)mm dome external diameter: ø 125mm 2.6kg Decorative frame × 1, Camera mounting bracket × 1, Camera base × 1, Camera base mounting screw × 4, Bullet terminal (female) × 2, Insulating sleeve × 2, Extension connector (alarm input, camera control, expansion) × 1 each, Safety wire × 1, CD-R (instruction manual of PDF) × 1 Ceiling mounting bracket: C-BC501*, Wall mounting bracket: C-BC501K, Ceiling suspension bracket: C-BC501T, flush ceiling mounting bracket: C-BC501U, Smoked dome cover: C-A 501DM * Use this bracket when mounting the camera on the ceiling surface (such as the plasterboard in the double ceiling) not strong enough to structurally support the weight of the camera. 5 APPEARANCE AND DIMENSIONAL DIAGRAM 83.5 • 255 preset positions • 230X zoom (optical 23X, electronic 10X) • Tilt rotation range 0° – 180° (using Auto-Flip function) • Pan rotation range continuous 360° • Pan/tilt maixmum high speed rotating speed is 360°/sec • 1/4 type CCD image device • 480 lines high resolution • Wide dynamic range • Autofocus • High-sensitivity function (color and B/W modes) • Preset sequency function (number/random sequence) • Privacy masking function • Auto-trace function • Autopan function • Preset image freeze function 239 Combination Camera System C-CC554S Operating Temperature Operating Humidity Application Waterproof Capability Finish Dimensions Weight Accessory Option Auto-pan, Preset Sequence, Auto-Trace (30s), Auto-Flip, Freeze Preset, Privacy Masking, Refresh Functions –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Under 90% (no due condensation produced) Indoors and under the eaves IP-52 Case/base: Aluminum die-casting, sand gray, paint Dome cover: Acrylic resin (transparent) Camera section external diameter: ø136 × 239 (H)mm dome external diameter: ø 125mm 2.6kg Decorative frame × 1, Camera mounting bracket × 1, Camera base × 1, Camera base mounting screw × 4, Bullet terminal (female) × 2, Insulating sleeve × 2, Extension connector (alarm input, camera control, expansion) × 1 each, Safety wire × 1, CD-R (instruction manual of PDF) × 1 Ceiling mounting bracket: C-BC501*, Wall mounting bracket: C-BC501K, Ceiling suspension bracket: C-BC501T, flush ceiling mounting bracket: C-BC501U, Smoked dome cover: C-A 501DM * Use this bracket when mounting the camera on the ceiling surface (such as the plasterboard in the double ceiling) not strong enough to structurally support the weight of the camera. COMBINATION DOME CAMERA APPEARANCE AND DIMENSIONAL DIAGRAM Camera control connector (5 pins, black) Alarm input connector (10 pins, white) Bullet terminal (male) Expansion connector (5 pins, white) Power cord length approx. 1.7 m BNC-R jack ø224 ø7 46 Composite cable length approx. 50 cm 83.5 4 – ø7.2 239 • 64 preset positions • 176X zoom (optical 22X, electronic 8X) • Tilt rotation range 0° – 90° • Pan rotation range continuous 360° • Pan/tilt maixmum high speed rotating speed is 360°/sec • 1/4 type CCD image device • 480 lines high resolution • Backlight compensation • Autofocus • High-sensitivity function (color mode) • Preset sequency function (number/random sequence) • Autopan function ø125 ø136 SPECIFICATIONS (PAL) Power source Power consumption Control Video Output Camera Control Terminal Alarm Input Auxiliary Contact Output Sensor Power Supply Synchronization Camera/Position ID No. of Preset Positions Camera Address Camera Image device Resolution S/N ratio Minimum Illumination 24V AC 50/60Hz 10W (normal operation), 25W max. RS-485 communications system VBS 1.0V(p-p) 75Ω RS-485 camera control connector (5 pins, black) 8 channels, no-voltage make contact input, open voltage: 18V DC short-circuit current; Under 2mA, alarm input connector (10 pins, white) 2 channels, open collector output, withstand voltage: 30V DC, permissible current: Under 100mA, expansion connector (5 pins, white) 18V DC, 40mA max., expansion connector (5 pins, white) Internal synchronization/power synchronization (phase adjustable when in power synchronization mode) 8 alphanumeric characters 64 Positions 001 – 999 Unit: mm SPECIFICATIONS (NTSC) Power source Power consumption Control Video Output Camera Control Terminal Alarm Input Auxiliary Contact Output Sensor Power Supply Synchronization Camera/Position ID No. of Preset Positions Camera Address Camera Image device Resolution S/N ratio Minimum Illumination 24V AC 50/60Hz 10W (normal operation), 25W max. RS-485 communications system VBS 1.0V(p-p) 75Ω RS-485 camera control connector (5 pins, black) 8 channels, no-voltage make contact input, open voltage: 18V DC short-circuit current; Under 2mA, alarm input connector (10 pins, white) 2 channels, open collector output, withstand voltage: 30V DC, permissible current: Under 100mA, expansion connector (5 pins, white) 18V DC, 40mA max., expansion connector (5 pins, white) Internal synchronization/power synchronization (phase adjustable when in power synchronization mode) 8 alphanumeric characters 64 Positions 001 – 999 1/4 type CCD Horizontal: 480 lines (at center) 50dB High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV) High-sensitivity function 0N: 0.1 lx (350mV), 0.03 lx (140mV) Backlight Compensation ON/OFF High-Sensitivity Function Slow shutter mode (32 times max.) White Balance ATW/AWB Flicker Reduction Automatic correction Electronic Zooming 8x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 22x Effective Focal Length f = 4.0 – 88mm Effective Angle of View Horizontal: 47.3° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T) Maximum Aperture F 1.6 (W) – F 3.8 (T) Zoom Speed WIDE end to TELE end Approx. 1.6s (preset operation), Approx. 2.9s (manual operation) Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: 0° to 90° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 120°/s max. (manual operation) 1/4 type CCD Horizontal: 480 lines (at center) 50dB High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV) High-sensitivity function 0N: 0.1 lx (350mV), 0.03 lx (140mV) Backlight Compensation ON/OFF High-Sensitivity Function Slow shutter mode (32 times max.) White Balance ATW/AWB Flicker Reduction Automatic correction Electronic Zooming 8x zooming Auto-Focus One push/stop AF/continuous Lens Zooming 22x Effective Focal Length f = 4.0 – 88mm Effective Angle of View Horizontal: 47.3° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T) Maximum Aperture F 1.6 (W) – F 3.8 (T) Zoom Speed WIDE end to TELE end Approx. 1.6s (preset operation), Approx. 2.9s (manual operation) Pan/Tilt Head Rotating Range Panning: Endless 360° rotation, Tilting: 0° to 90° Rotating Speed Panning/Tilting: 360°/s max. (preset operation), 120°/s max. (manual operation) Other Function Operating Temperature Operating Humidity Application Waterproof Capability Finish Other Function Operating Temperature Operating Humidity Application Waterproof Capability Finish Dimensions Weight Accessory Option Auto-pan, Preset Sequence, Refresh Functions –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Under 90% (no due condensation produced) Indoors and under the eaves IP-52 Case/base: Aluminum die-casting, sand gray, paint Dome cover: Acrylic resin (transparent) Camera section external diameter: ø136 × 239 (H)mm (dome external diameter: ø 125mm) 2.6kg Decorative frame × 1, Camera mounting bracket × 1, Camera base × 1, Camera base mounting screw × 4, Bullet terminal (female) × 2, Insulating sleeve × 2, Extension connector (alarm input, camera control, expansion) × 1 each, Safety wire × 1, CD-R (instruction manual of PDF) × 1 Ceiling mounting bracket: C-BC501*, Wall mounting bracket: C-BC501K, Ceiling suspension bracket: C-BC501T, flush ceiling mounting bracket: C-BC501U, Smoked dome cover: C-A 501DM * Use this bracket when mounting the camera on the ceiling surface (such as the plasterboard in the double ceiling) not strong enough to structurally support the weight of the camera. Combination Camera System C-CC504S Dimensions Weight Accessory Option Auto-pan, Preset Sequence, Refresh Functions –10˚C to +50˚C (continuously active for operation at temperature below 0°C) Under 90% (no due condensation produced) Indoors and under the eaves IP-52 Case/base: Aluminum die-casting, sand gray, paint Dome cover: Acrylic resin (transparent) Camera section external diameter: ø136 × 239 (H)mm (dome external diameter: ø 125mm) 2.6kg Decorative frame × 1, Camera mounting bracket × 1, Camera base × 1, Camera base mounting screw × 4, Bullet terminal (female) × 2, Insulating sleeve × 2, Extension connector (alarm input, camera control, expansion) × 1 each, Safety wire × 1, CD-R (instruction manual of PDF) × 1 Ceiling mounting bracket: C-BC501*, Wall mounting bracket: C-BC501K, Ceiling suspension bracket: C-BC501T, flush ceiling mounting bracket: C-BC501U, Smoked dome cover: C-A 501DM * Use this bracket when mounting the camera on the ceiling surface (such as the plasterboard in the double ceiling) not strong enough to structurally support the weight of the camera. 6 Combination Camera System C-CC554S/C-CC504S BRACKETS AND DOME COVER C-BC501 Anchor bolt mounting hole 46 92 Ceiling Mounting Bracket C-BC501U ø7 2–ø7 Flush Ceiling Mounting Bracket ø200 11 x 20 25 Applicable Camera C-CC504S, C-CC554S (option) Unit: mm Under 40 mm in thickness Surface-treated steel plate ø200 x 173.2 (D) mm 860 g Safety wire (1 m)...1, Pattern paper...1, Camera holder mounting screw...1 set Applicable Camera C-CC504S, C-CC554S, (option) Unit: mm C-A501DM 64.1 Smoked Dome Cover 18.5 Drop prevention screw (M5) (accessory) 18 4–ø5 18 C-BC501T Ceiling Suspension Bracket 9.6 1.8 Mountable Board Finish Dimensions Weight Accessory Under 40 mm in thickness Surface-treated steel plate 130 (W) x 41.8 (H) x 92 (D) mm 130 g Safety wire (1 m)...1, Bracket mounting screw...4 37 8–ø3 82 Mountable Board Finish Dimensions Weight Accessory 40 The TOA C-BC501 Ceiling Mounting Bracket is specially designed to mount TOA’s Combination Dome Cameras directly on the wall. The bracket facilitates mounting of the camera on the plasterboard in the double ceiling or other locations where the mounting screws cannot be installed securely. 163.6 The C-BC501U bracket is designed to be exclusively used for flush ceiling mounting of TOA’s Combination Dome Camera. Use this bracket when mounting the camera to the ceiling surface where the fixing screws cannot be securely installed, such as on the plaster panel of the dual-construction ceiling. Also use this bracket to minimize the exposure of the camera. 83.5 130 ø125 ø130 218.5 54.1 Dimensions Weight Accessory 37 Pipe: Stainless steel pipe Resin cover: ABS resin, sand gray Metal part: Surface-treated steel plate ø126 x 218.5 mm 580 g Safety wire (1 m)...1, Mounting screw...1set, Pattern paper...1 ø126 54.1 18.5 Finish 60.5 ø32 The TOA C-BC501T Ceiling Suspension Bracket is specially designed to mount TOA’s Combination Dome Cameras in hanging ceiling installations. 64.1 Applicable Camera C-CC504S, C-CC554S (option) Unit: mm The TOA C-A501DM Smoked Dome Cover is specially designed to be used in conjunction with TOA’s Combination Dome Cameras. The Dome Cover is used to make it difficult for individuals to see the camera’s orientation. Transmissivity Finish Dimensions Weight Applicable Camera (option) Approx. 20% * Acrylic resin (smoked) ø130 x 82 (H) mm 60 g C-CC504S, C-CC554S * As a general guideline, the minimum object illumination of the camera equipped with the Smoked Dome Cover is approximately 5 times that of the camera without the cover. Unit: mm C-BC501K The TOA C-BC501K Wall Mounting Bracket is specially designed to mount TOA’s Combination Dome Cameras to wall surfaces. Install the unit only in a location that can structurally support the weight of the unit and camera. 140 46 17.3 Wall Mounting Bracket 83.5 235 150 Dimensions Weight Accessory Applicable Camera C-CC504S, C-CC554S (option) 7 170 Resin cover: ABS resin, sand gray Metal part: Surface-treated steel plate 170 (W) x 140 (H) x 235 (D) mm 1.1 kg Mounting screw...1set, Cable clip...2 7 ø4.3 Finish ø7.5 Unit: mm SETTING GUIDE Combination Camera System C-CC554S/C-CC504S SETTING GUIDE The camera menu screens are comprised of the following setting item screens. CAMERA MENU PRESET ID SETTING CAMERA AUTO MODE Setting Item Programs the camera position (camera orientation), displays setting status, and deletes set data. PRESET MEMORY Programs the camera position. MEMORY MAP Displays the set position status. MEMORY RESET Deletes the programmed position. ID SETTING Sets the title. DISPLAY Displays camera/position numbers and their titles. CAMERA ID Sets the camera title. POS ID Sets the position title. ALL DISPLAYS *1 Sets the location of the title displays on the monitor. POS LOCATIONS *1 LOCATION SHIFT CAMERA Assigns the same title display location to all camera positions or different display locations to individual camera positions. Fine-adjusts the title display locations on the monitor. SYNC Enables camera synchronization and adjusts the phase. PASSWORD Sets the password for entering the camera menu screen. PRIVACY MASK *2 DATA XFER Note: This setting is for maintenance purposes only. Do not use in normal operation. AGC Automatically adjusts the camera's brightness. SHUTTER SPEED *1 Sets the shutter speed. Assigns priority to either B/W mode or slow shutter mode depending on the subject's lighting conditions. B/W MODE *2 SLOW SHUTTER Sets the slow shutter limit. AUTO FOCUS Sets the most appropriate auto focus mode. RESET Returns each item on the camera setting screen to the factorypreset status. AUTO MODE Sets Auto-Pan, Sequence, and Trace functions to automatic operation. AUTO KEY Assigns automatic functions to the Auto key. AUTO PAN Selects the Auto-Pan function's Reverse or Skip mode. PAN PAUSE TIME *1 Sets the duration to stops at the end of travel during Auto- Pan operation. PAN SPEED Sets the Auto-Pan speed. PAN DIRECTION Sets the direction of Auto-Pan rotation. PAN LIMIT SETTING Sets the Auto-Pan function's left and right limit positions. PAN LIMIT RESET Disables the Auto-Pan function's set left and right limit positions. Sets camera properties. WHITE BALANCE *1 Sets the camera's white balance. BACKLIGHT *1 Sets the backlight compensation. BRIGHTNESS *1 Adjusts the camera's brightness. SPECIAL Sets various camera characteristics. E-ZOOM AUTO REFRESH Sets the maximum electronic zoom power. Sets the automatic refresh function (restoring images displaced by position reproduction or removing dirt of horizontally rotating parts). ENHANCER Sets the contour enhancement function. CHROMA LEVEL Adjusts the chroma level. PRESET FREEZE *2 Freezes the display prior to position reproduction. AUTO FLIP *2 Reverses the displayed images. Sets locations to be masked out of view. Transfers data between camera unit and base unit. SEQUENCE Sets the order of sequential camera position displays (sequencing set camera positions to the monitor). SEQ INTERVAL *1 Sets the interval of Sequence displays. TRACE *2 Stores Trace movements (automatically following a set path between 2 predetermined points). TRACE PAUSE TIME *2 Sets the duration of pause interval between Trace operations when continuously repeating Trace displays. *1 Can also be changed for individual positions at the camera setting screen for individual positions. *2 Can be only set for the C-CC554S. 8 REMOTE CONTROLLER APPEARANCE AND DIMENSIONAL DIAGRAM 10˚ 57.9 326 ● Control up to 16 TOA's Combination Dome Cameras Realtime control as well as preprogrammed position retrieval of up to 255 positions is provided. Each position allows providing a specific title as well remote image quality adjustment. ● Instant position recall The most used camera and position numbers can be assigned to function keys A through H for one-touch instant recall. Other camera numbers and position numbers can be assigned to ID numbers from 1 through 512 and easily retrieved using the tenkey pad. ● Controls Multiplexer The C-RM500 can also control the TOA multiplexers and allows switching video image display modes – single screen, single screen in sequence, 4-screens in sequence, as well as 4, 9, 10 and 16-segment split screens. ● Alarm capability Alarm signals received by the alarm input of combination dome cameras can be transmitted to the C-RM500 via a pair of RS-485 communication line where the C-RM500’s alarm operations can be activated, based on the alarm signal type received. This has reduced the number of signal lines that were conventionally required in an expanded system. An Alarm Hold function allows temporarily suspending automatic switching of video images triggered by an alarm to enable the operator to prioritise the screen currently being viewed. In addition, the CRM500 can receive alarm signals from an C-AL80 unit through the RS-232C port. ● 2 Location Control The system can be independently controlled in two separate locations by installing 2 C-RM500 units. 31.7 25 63.3 185.2 62 The C-RM500 Remote Controller is designed for use in camerabased systems that allow remote control from up to 1.2km away over RS-485 communication lines. It allows video images to be switched remotely and can handle a maximum of 16 TOA's Combination Dome Cameras when used together with the TOA Multiplexer. Easy-to-see LEDs inform status of control, alarm, focus and other functions. 181 Combination Camera System C-RM500 Figure of the installed unit Unit: mm SPECIFICATIONS Power Source Current Consumption Slave Remote Controller Camera Control Switcher Control Alarm Input Alarm Output/ Control Input Display setting, Alarm Signal Number of Unit Connections Maximum Cable Distance Operating Temperature Operating Humidity Finish Dimensions Weight Accessory Applicable Model (option) 12 V DC 150 mA RS-485, screwless connector RS-485, screwless connector (*1) RS-485, screwless connector RS-232C, D-sub connector (9 pins, male) RS-232C, D-sub connector (9 pins, male) Alarm output: 16 channels, NPN open collector output, withstand voltage: 30 V DC, control current: 20 mA Alarm input: 1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: 5 mA max. Home position selection input: 1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: 5 mA max. D-sub connector (25-pins, female) LED indication of control status, alarm status, alarm hold status, still picture status, defroster, auxiliary auto, auto focus, and lens speed LCD indication of key entry confirmation Continuous alarm tone (can be turned on and off) Up to 2 (one to be set for MASTER unit, another for SLAVE unit) 1.2 km (*2) (between the Remote controller and the Combination cameras) 0°C to +50°C Under 90% RH (no due condensation produced) Panel: Surface-treated steel plate, sand gray, paint Sides: Rubber 326 (W) × 62 (H) × 185.2 (D) mm 1.8 kg D-sub connector (9 pins, male) × 1, D-sub connector(25 pins, male) × 1 Combination dome camera: C-CC504S, C-CC554S Switcher: C-MS161D, C-MS91D Slave remote controller: C-RM500 Interface unit: C-IF500 Alarm unit: C-AL80 (*1) Can connect up to 31 units mixing with combination cameras and interface units. (*2) Applies to the system where the unit and combination camera are connected in a matched pair. Represents the total of connected cable distances if multiple combination cameras or interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used). 9 INTERFACE UNIT ALARM UNIT A useful option for configuring camera systems, the C-IF500 functions as a splitter. It provides control over expanding a camera system when the distance is over 1.2km (max. 3km) between the dedicated C-RM500 Remote Controller and system cameras linked to it. It will also allow configuring a star connection. Receiving the RS-485 communication line serial signals, the C-IF500 splits the signals into 4-channel data for slave units and converts into RS-232C data to be used for public line or fiber optics communication. Data communication between master and slave terminals is bidirectional. The C-IF500 also allows easily setting the data communication data transfer rate in four increments via DIP switch to suit network requirements. The C-AL80 Alarm Unit serves as the main controller for the alarm requirements of a system by converting alarm signals initiated by externally connected equipment into RS-232C-compatible signal data. In addition to its 32 alarm or remote inputs, the C-AL80 can also be linked to a maximum of 8 other C-AL80 units in master/ slave configurations. This provides a total of 256 alarm or remote inputs to be transmitted to the C-RM500 remote controller. APPEARANCE AND DIMENSIONAL DIAGRAM APPEARANCE AND DIMENSIONAL DIAGRAM Combination Camera System C-AL80 C-IF500 420 44 46 88.4 96.6 210 Front cover 335.8 319.8 284.1 279.8 11 Enlarged figure for the inside of a front cover Unit: mm SPECIFICATIONS Power Source Current Consumption External Control Display Maximum Cable Distance Communication Speed Operating Temperature Operating Humidity Finish Dimensions Weight Option 12 V DC 100 mA Master: RS-485, screwless connector terminating resistance (100 Ω) switch ON/OFF Slave(*1): 4 channel, RS-485, screwless connector RS-232C, D-sub connector (9-pin, male) Power LED indicator, communication LED indicators (TX, RX) RS-485: 1.2 km (*2) RS-232C: 10 m 4800 bps, 9600 bps, 19200 bps, 38400 bps –10°C to +50°C Under 90% RH (no due condensation produced) Panel: Aluminum, black, 30% gloss, paint Case: Pre-coated steel plate, 30% gloss, black 210 (W) x 46 (H) x 284.1 (D) mm 1.4 kg Rack mounting bracket: M-15B-BK (for rack mounting one C-IF500 unit) MB-15B-J (for rack mounting two C-IF500 units) (*1) Communications cannot be made between slave terminals. Each slave terminal can connect up to 31 cameras. (except RS-232C port) (*2) Applies to the system where the unit and combination camera are connected in a matched pair. Represents the total of connected cable distances if multiple combination cameras or Interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used). Unit: mm SPECIFICATIONS (H/L) Power Source Power Consumption Alarm/Remote Input Control Input/Output Master/sub Connection Terminal Alarm Reset Input Setting Switches Application Operating Temperature Finish Dimensions Weight Accessory Option Application Model H: 230 V AC, 50/60 Hz L: 120 V AC, 50/60 under 3 W 32 channels, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: max. 5 mA, M3 screw terminal, distance between barriers: 7.62 mm 1 channel, RS-232C, D-sub connector (9 P, male) (only valid for master unit), fixed to 38,400 bps 2 channels, RS-485, maximum cable length: 1200m, DIN connector (5 P) 1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: max. 5 mA, D-sub connector (25 P) Master/Slave: 3-bit DIP switch (Selection of Master or Slave 1—7) Alarm/Remote: 1-bit DIP switch (Alarm/Remote selection) Alarm time: 1-bit DIP switch (Edge/Level selection) RS-485 terminal: Rear-mounted slide switch (RS-485 termination, Enable/Disable selection) Indoor use 0°C to +50°C Panel: Aluminum extrusion, black, 30% gloss Case: Pre-coated steel plate, black, 30% gloss 420 (W) × 96.6 (H) × 335.8 (D) mm 3.6 kg DIN plug × 2, RS-232C cable (2 m) × 1, D-sub connector (25 P) × 2, Power cord (2 m) × 1 Rack mounting bracket: MB-23B Remote controller: C-RM500 10 Combination Camera System C-CC554S/C-CC504S Configuring a perfect surveillance system. ■ High resolution ■ Closeup zooming The cameras feature a high horizontal resolution of 480 lines (NTSC/PAL) for high quality images. To enable accurate surveillance from a remote location, TOA's combination dome cameras feature highly two effective zoom modes — optical and electronic for enlarging the view beyond the optical zoom. Optical mode uses the lens to achieve a 22X (C-CC504S) or 23X (C-CC554S) zoom. The digital signal processing abilities built-into these units makes use of video memory to increase electronic sensitivity so that electronic zoom up to a maximum of 176X for the C-CC504S and 230X for the C-CC554S can be used. ■ Versatile installation Designed to be compatible with various installation conditions, the cameras feature a water and dust-resistant construction (conforming to IP52 requirements). ■ Silent operation Effective surveillance needs to be silent. When operating, noise levels measured at just 25dB (A weighting) make sure cameras do not call attention to themselves. ■ All-seeing high speed eyes TOA's combination dome cameras don't miss a thing with their extended rotation range of 360° that covers every position point. The maximum high-speed rotating (pan/tilt) speed of 360°/second can also be slowed down as desired. 360˚ ■ Wide Dynamic Range Function* TOA's combination dome cameras based on conventional technology met problems when the target field contained areas of different brightness. As these photographs visually illustrate the point, focusing on outdoor makes indoor too dark to comprehend (Photo A). On the other hand, focusing on indoor created whiteout of outdoor (Photo B). Combination Dome Cameras overcome this problem by use of special DSP. The result is single clear image resembling that of a human eyesight. High-speed shutter loses details of indoor. (Photo A) ■ Presetting camera positions Maximizing user convenience, these cameras allow covering 255 (C-CC554S) or 64 (C-CC504S) different positions. That allows a complete coverage of the area under a camera's surveillance. Camera direction, lens field of view angle and focus can all be preset. Up to 8 alphanumeric characters can be used to title each camera position utilized for identification and quick reference. ■ Versatile autofocus modes To suit application needs, TOA's cameras provide sophisticated auto-focusing with three modes. For normal operation, a single push activates auto focus. Stop Auto Focus is activated whenever the camera view or angle of view is changed. Continuous auto focus mode keeps the auto focus in continuous operation. ■ Electronic sensitivity boost and B/W (black/white) mode. Shutter speed can be adjusted down from a default setting for a higher sensitivity point to optimize image quality. Dark areas can be made up to 32 times brighter. The C-CC554S in addition, also provides a choice of B/W mode to monitor a target and target areas that cannot be seen in normal light. Low-speed shutter creates whiteout of outdoor. (Photo B) Sensitivity boost allows cameras to provide good color image quality for dark areas. (color image) Electronically combining the images taken using both low-speed and highspeed shutter gives single clear image. C-CC554S B/W mode. (B/W image) 11 ■ Auto flip function* Combination Camera System FEATURES ■ Camera title and position reference 180˚ Switching this function (Tilt: 0° – 180°) on prevents having to see an inverted image on the monitor when the camera rotates vertically through a 180° arc of travel. This function automatically flips over the image shown on a monitor so the image is always right side up. Each camera is equipped with an alarm input that handles a maximum of 8 alarms, allowing sensors to be connected, increasing overall system reliability. ■ Route tracing (Auto trace function)* ■ Discretionary surveillance with privacy A camera can be set to monitor preset points for up to 30 seconds, allowing a subject to be traced along a route. ■ Autopan function To effectively monitor a wide area, the autopan function's default Reverse mode allows selecting the left and right limits of camera travel so that it pans automatically between the set travel points. In Skip mode, the camera returns to its starting point before panning again. Selectable parameters for this mode include setting the degree of pan travel and the time between completion of a pan and the start of the next pan. A useful display mode allows setting a title for each camera and position to be displayed on a monitor so that each camera as well as position can be confirmed. ■ Alarms enhance system reliability masking* Each camera allows up to 2 locations in a camera's field of view to be masked to protect privacy. ■ Flicker-free operation Even when used where the AC is at 50Hz instead of the more conventional 60Hz, TOA cameras remain free from flicker. For areas with fluorescent lighting, a flicker-reduction switch can be used to switch shutter speed. *C-CC554S only ■ Variable speed function Using lens zooming will automatically set panning speed to ensure optimum performance. ■ Preset Freeze function The Preset Freeze function can be set to stop a camera displaying its view as it moves from one location to another. A pre-recorded image can be designated and displayed on the monitor as the camera moves. ■ Preset sequence function* This function allows presetting the positions to be monitored in numbered sequence or at random. It provides one touch operation for initiating a sequence as well as randomly accessing any desired position. Function Comparison Chart Number of Preset Positions Zooming C-CC504S 64 176x optical 22x/ electronic 8x 0° – 90° — ● ( Tilt Rotation Range Wide Dynamic range Function Auto-Focus High-Sensitivity Function Color mode Day/night camera mode Auto-Flip Function Privacy Masking Function Auto-Trace Function Preset Sequence Function Auto-pan Function Preset Freeze Function ) ● — — — — ● ● — C-CC554S 255 230x optical 23x/ electronic10x 0° – 180° ● ● ( ) ● ● ● ● ● ● ● ● 12 Combination Camera System C-CC554S/C-CC504S SYSTEM EXAMPLES 1. Combination Dome Camera (1 unit) 2. Combination Dome Cameras (4 units) Remote Controller C-RM500 Combination Dome Cameras C-CC554S Remote Controller C-RM500 Combination Dome Cameras C-CC554S C-QA40 Monitor Quad Adapter Monitor 4. When Combination Dome Camera and Remote Controller are separated by more than 1.2km. 3. Combination Dome Camera (16 units) Combination Dome Cameras C-CC554S max. 3km max. C-IF500 Remote Controller C-RM500 Combination Dome Cameras C-CC554S Multiplexer 16 C-IF500 Remote Controller C-RM500 C-MS161D Monitor CC-3331B Cable Compensator 5. Sensor-activated Dome Camera operation. Sensor max. 8 Combination Dome Cameras C-CC554S C-MS161D max. 8 Remote Controller C-RM500 RS-232C Multiplexer Sensor Monitor C-AL80 max. 8 max. 256 C-AL80 Alarm Unit C-AL80 13 Monitor N-CC1110 N-CC1000 Network Camera Network Camera (Lens is optional) (Lens is included) N-SD1040 4-Channel Software Decoder DESCRIPTION This system allows network-based transmission of moving images for monitoring and remote surveillance even at a low transmission rate, something not previously possible. It was made possible by incorporating H.263/H.261 compression methods, which are advanced enough to offer satisfactory moving image viewing at a low transmission rate. TOA network cameras, N-CC1000 and N-CC1110, feature the most in-demand monitor functions and performance. With system outputs that can be directly linked to LAN, remote monitoring and surveillance are now possible as well as full remote control capability. The N-VT1010 converts analog signals from cameras to digital data that can be transmitted via a network. Each unit comes supplied with 1 channel software and an optional N-SD1040 4 channels software package is also available. The software allows all monitored images to be seen on a PC as well as perform system-wide control. FEATURES ● High performance realtime moving images TOA allows its cameras to efficiently interface directly with LANs, even for realtime image transmission. TOA overcomes limitations by employing special H. 261 and H. 263 compression protocols that enable images to be transmitted with satisfactory quality even at relatively low transmission speeds. Able to effectively transmit data to multiple locations, TOA cameras with their excellent image quality are also ideal for use as surveillance cameras when used in conjunction with TOA’s software decoder and a personal computer. ● Multicast function (max. 5 sites) Allows data to be received at multiple sites simultaneously without having to lower frame rates. Image transmission maintains a max. 30 frames per second rate to allow smooth, easy to view images. Network Camera System NETWORK CAMERA SYSTEM N-VT1010 Network Video Transmitter ● Adjustable transmission rate Transmission rates can easily be adjusted to suit user preferences and network requirements through the easy menu-driven operation software. Remarkably, even at low speeds, moving images can be effectively transmitted. ● Ideal camera for surveillance TOA Network cameras incorporate ideal functions and features for use in surveillance applications. In particular, the N-CC1000 features enhanced electronic sensitivity for use in poor nighttime conditions as well as a wide dynamic function for clear images even in a backlight condition. This camera accommodates CS mount lens so various lenses can be selected to suit specific applications. In addition, the N-CC1110 camera featuring a 2X zoom with variable focal lens is also available. ● Control dome cameras and multiplexer via network A multiplexer and combination dome cameras can be connected to the N-VT1010 which will enable putting them on a network to allow enhanced use with remote control capability over many functions. With a PC, a system of up to 16 cameras can be effectively controlled. Settings for camera operation include 360° coverage per second, 23x zoom and others. Now remote and simultaneous surveillance are easier to accomplish than ever before. A useful Pre alarm recording function on N-VT1010 retains up to 2 minutes of camera footage to allow seeing what occurred just before the alarm was activated. ● Easy to operate software Each N-CC1000, N-CC1110 and N-VT1010 comes with a 1channel Software Decoder. This software is straight-forward and allows bi-directional data transmission as well as simplifies configuring system parameters as desired, from setting transmission rate to camera confirmation and prealarm functions among others. For monitoring four cameras at a single location, the N-SD1040 4-Channel Software Decoder can be used. 14 N-CC1000 Network Camera System NETWORK CAMERA (Lens is optional) APPEARANCE AND DIMENSIONAL DIAGRAM 175 71 68.5 60 122.5 18 (Includes 1-channel software decoder) 25.3 2 – 1/4 –20UNC • Wide dynamic range Provides a new level of performance with natural looking images even in poor light conditions. • Backlight compensation Ensures perfect images in areas with various degrees of lighting. • Maximum 32X sensitivity booster • CS mount (lens is optional) • 1-channel Software Decoder provided • Directly connects to LAN SPECIFICATIONS (PAL) Power Source Current Consumption Power Terminal Camera Image device Number of Effective Pixels Monitor Output Monitor Output Resolution Monitor Output S/N ratio Minimum Required Illumination Recommended Illumination AES Range Dynamic range Shutter Speed* AGC* Sensitivity Up* White Balance Chroma Level* Enhancer Level* Lens Mount Auto-Iris Lens Output Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate* Character Display Serial Port Alarm Input* Alarm Output* Part of Consumption Operating Temperature Operating Humidity Finish Dimensions Weight Accessory 15 SPECIFICATIONS (NTSC) 12V DC (10.8 – 15.8V DC) 0.7A Cage clamp [Solid cable: ø0.4 – ø1.2 (AWG26 – 16) Stranded cable: 0.3 – 1.25mm2 (AWG22 – 16) diameter of conductor: over ø0.18mm] AC adapter socket (RC6705, center + ) 1/3 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) VBS 1.0 V(p-p), 75Ω, BNC jack Horizontal: 480 lines, Vertical: 350 lines 48dB (AGC OFF) 3 lx (F1.4, 50%) (sensitivity up: OFF) 0.03 lx (F0.8, 50%) (sensitivity up: 32 times) Over 300 lx (F2.8) 1: 600 (F1.4 – 31) 46dB (wide dynamic range ON) (However manual and fixed Iris lens isn't supported) 1/50, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 Automatic/Fixed (0, 2, 4, 8, 16dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (MIN – MAX) Normal/Manual (soft – sharp) CS mount DC input type with a 4P connector RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 288, 704 × 576 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel 19 characters max. (alphanumeric) not output at the monitor output RS-232C, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, loop resistance: under 100Ω Relay contact (active state: make or break selectable), contact capacity: 30V DC, 1A Manganese dioxide lithium battery/about 10 years –10˚C to +50˚C Under 90% RH (no due condensation produced) Case: Aluminum metallic silver, paint 71 (W) × 68.5 (H) × 175 (D)mm 750g CD-R × 1 (Software Decoder, Active X Control, Jet Manager, Manuals) * To be set on Internet Explorer Power Source Current Consumption Power Terminal Camera Image device Number of Effective Pixels Monitor Output Monitor Output Resolution Monitor Output S/N ratio Minimum Required Illumination Recommended Illumination AES Range Dynamic range Shutter Speed* AGC* Sensitivity Up* White Balance Chroma Level* Enhancer Level* Lens Mount Auto-Iris Lens Output Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate* Character Display Serial Port Alarm Input* Alarm Output* Part of Consumption Operating Temperature Operating Humidity Finish Dimensions Weight Accessory 12V DC (10.8 – 15.8V DC) 0.7A Cage clamp [Solid cable: ø0.4 – ø1.2 (AWG26 – 16) Stranded cable: 0.3 – 1.25mm2 (AWG22 – 16) diameter of conductor: over ø0.18mm] AC adapter socket (RC6705, center + ) 1/3 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) VBS 1.0 V(p-p), 75Ω, BNC jack Horizontal: 480 lines, Vertical: 350 lines 48dB (AGC OFF) 3 lx (F1.4, 50%) (sensitivity up: OFF) 0.03 lx (F0.8, 50%) (sensitivity up: 32 times) Over 300 lx (F2.8) 1: 500 (F1.4 – 31) 46dB (wide dynamic range ON) (However manual and fixed Iris lens isn't supported) 1/60, 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 Automatic/Fixed (0, 2, 4, 8, 16dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (MIN – MAX) Normal/Manual (soft – sharp) CS mount DC input type with a 4P connector RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 240, 704 × 480 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel 19 characters max. (alphanumeric) not output at the monitor output RS-232C, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, loop resistance: under 100Ω Relay contact (active state: make or break selectable), contact capacity: 30V DC, 1A Manganese dioxide lithium battery/about 10 years –10˚C to +50˚C Under 90% RH (no due condensation produced) Case: Aluminum metallic silver, paint 71 (W) × 68.5 (H) × 175 (D)mm 750g CD-R × 1 (Software Decoder, Active X Control, Jet Manager, Manuals) * To be set on Internet Explorer N-CC1110 (Lens is included) APPEARANCE AND DIMENSIONAL DIAGRAM 71 68.5 60 211 Network Camera System NETWORK CAMERA 2 – 1/4 –20UNC 18 61.3 (Includes 1-channel software decoder) • Backlight compensation Ensures perfect images in areas with various degrees of lighting. • Comes standard with a 2X manual zoom lens. • 1-channel Software Decoder provided • Directly connects to LAN SPECIFICATIONS (PAL) Power Source Current Consumption Power Terminal Camera Image device Number of Effective Pixels Monitor Output Monitor Output Resolution Monitor Output S/N ratio Minimum Required Illumination White Balance Adjustment Switch Other Functions Built-in Lens Angle of View Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate* Character Display Serial Port Alarm Input* Alarm Output* Part of Consumption Operating Temperature Operating Humidity Finish Dimensions Weight Accessory SPECIFICATIONS (NTSC) 12V DC (10.8 – 15.8V DC) 0.7A Cage clamp [Solid cable: ø0.4 – ø1.2 (AWG26 – 16) Stranded cable: 0.3 – 1.25mm2 (AWG22 – 16) diameter of conductor: over ø0.18mm] AC adapter socket (RC6705, center + ) 1/4 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) VBS 1.0 V(p-p), 75Ω, BNC jack Horizontal: 480 lines, Vertical: 350 lines 48dB 3 lx (50%) ATW ON/OFF (used for focus adjustment) Flicker reduction, backlight compensation, iris adjustment Focal length: f=3.0 – 6.0mm (auto-iris) Horizontal: 71.9° – 36.0°, Vertical: 52.0° – 26.8°, Diagonal: 96.3° – 45.4° RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 288, 704 × 576 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel 19 characters max. (alphanumeric) not output at the monitor output RS-232C, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, loop resistance: under 100Ω Relay contact (active state: make or break selectable), Contact capacity: 30 V DC, 1A Manganese dioxide lithium battery/about 10 years –10˚C to +50˚C Under 90% RH (no due condensation produced) Case: Aluminum metallic silver, paint 71 (W) × 68.5 (H) × 211 (D)mm 750g CD-R × 1 (Software Decoder, Active X Control, Jet Manager, Manuals) * To be set on Internet Explorer Power Source Current Consumption Power Terminal Camera Image device Number of Effective Pixels Monitor Output Monitor Output Resolution Monitor Output S/N ratio Minimum Required Illumination White Balance Adjustment Switch Other Functions Built-in Lens Angle of View Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate* Character Display Serial Port Alarm Input* Alarm Output* Part of Consumption Operating Temperature Operating Humidity Finish Dimensions Weight Accessory 12V DC (10.8 – 15.8V DC) 0.7A Cage clamp [Solid cable: ø0.4 – ø1.2 (AWG26 – 16) Stranded cable: 0.3 – 1.25mm2 (AWG22 – 16) diameter of conductor: over ø0.18mm] AC adapter socket (RC6705, center + ) 1/4 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) VBS 1.0 V(p-p), 75Ω, BNC jack Horizontal: 480 lines, Vertical: 350 lines 48dB 3 lx (50%) ATW ON/OFF (used for focus adjustment) Flicker reduction, backlight compensation, iris adjustment Focal length: f=3.0 – 6.0mm (auto-iris) Horizontal: 71.9° – 36.0°, Vertical: 52.0° – 26.8°, Diagonal: 96.3° – 45.4° RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 240, 704 × 480 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel 19 characters max. (alphanumeric) not output at the monitor output RS-232C, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, loop resistance: under 100Ω Relay contact (active state: make or break selectable), Contact capacity: 30 V DC, 1A Manganese dioxide lithium battery/about 10 years –10˚C to +50˚C Under 90% RH (no due condensation produced) Case: Aluminum metallic silver, paint 71 (W) × 68.5 (H) × 211 (D)mm 750g CD-R × 1 (Software Decoder, Active X Control, Jet Manager, Manuals) * To be set on Internet Explorer 16 N-VT1010 Network Camera System NETWORK VIDEO TRANSMITTER SPECIFICATIONS (H) for PAL only Power Source Current Consumption Video Input Serial Port* Alarm Input* Alarm Output* Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate 220 – 240V AC, 50/60Hz 0.1A VBS 1.0 V(p-p), 75Ω, BNC jack, PAL RS-232C/RS-422, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, resistance: under 100Ω Relay contact (active state: make of break selectable), Contact capacity: 30V DC, 1A RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 288, 704 × 576 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel (Includes 1-channel software decoder) Character Display Operating Temperature The N-VT1010 Network Video Transmitter is designed to convert analog composite video signals into digital video signals to allow them to be transmitted over a 10BASE-T. Fully compliant with the established H.323 standard so that moving images can be transmitted in real time, the N-VT1010 also incorporates the H.261 and H.263 compression methods for moving images. This provides satisfactory real-time viewing of moving images even when transmitted over a LAN at a low transmission rate. In addition, a multicast function allows data to be simultaneously received at up to 5 locations without degrading frame rates. Remote control over TOA multiplexer and combination dome cameras is also possible. Camera settings and controls can be adjusted via a PC on the network if the N-VT1010 is connected to a combination dome camera in a 1:1 ratio . Operating Humidity Finish Dimensions Weight Accessory Option * To be set on the Internet Explorer SPECIFICATIONS (L) for NTSC only Power Source Power Consumption Video Input Serial Port* Alarm Input* 110 – 120V AC, 50/60Hz 7W VBS 1.0 V(p-p), 75Ω, BNC jack, NTSC RS-232C/RS-422, D-sub connector (9 pins, male) No-voltage relay contact (active state: make or break selectable), Open voltage: 3.3V DC, short-circuit current: 5mA, resistance: under 100Ω Relay contact (active state: make of break selectable), Contact capacity: 30V DC, 1A Alarm Output* APPEARANCE AND DIMENSIONAL DIAGRAM 44 53.3 Character Display Operating Temperature Operating Humidity Finish Dimensions Weight Accessory 296 4.5 Network Network Port Network Protocol Compression Method/ Resolution* Frame Rate Data Rate 210 280 Option unit: mm NOTES: 1. When connecting the camera to a network that is not DHCP-compatible, the IP address, sub-net mask, and gateway IP address need to be set for the transmitter. 2. Using the unicast function to make multiple simultaneous transmissions may result in a decreased frame rate. 3. When using the multicast function, the network must be multicast-compatible. 4. In multicast transmissions, if the receiver's requested data rate differs from that of the transmitter, communications are automatically performed at the minimum data rate. 5. In data streaming applications, data is distributed from the transmitter over the network at all times, even when no other equipment is connected to the network. 6. Be sure to use a leased line when viewing from remote locations. Viewing via the Internet may result in problems with security or frame rate decrease. 7. Control is performed on a first-come-first-served basis when controlling the Combination Camera, etc. from multiple sites. The right of control is automatically cancelled should there be no control data for 15 seconds. 8. In data streaming applications, reception is only possible with Internet Explorer. No data can be received using the Software Decoder. 9. A personal computer is required to perform initial Network Video Transmitter settings. 10. The Software Decoder is not compatible with Macintosh or Unix operating systems. 17 19 characters max. (alphanumeric) 0˚C to +50˚C (Mount a perforated panel above and below the unit when rack-mounting.) Under 90% RH (no due condensation produced) Case: Pre-coated steel plate, black, 30% gloss 210 (W) × 53.3 (H) × 290 (D)mm 1.8kg CD-R (Software Decoder, Active X Control, Jet Manager, Manuals) × 1, AC power cord (2m) × 1, D-sub connector (9 pins, female) × 1 MB-15B-BK: For rackmounting two N-VT1010 units MB-15B-J: For rackmounting N-VT1010 unit RJ-45 (10BASE-T) TCP, UDP, ARP, ICMP, FTP, DHCP, HTTP, RTP, IP, IGMP H.261: QCIF, CIF H.263: QCIF, CIF, 2CIF JPEG: 352 × 240, 704 × 480 CIF: 30 frame/s max., 2CIF: 16 frame/s max. 10k – 1M bps per channel 19 characters max. (alphanumeric) 0˚C to +50˚C (Mount a perforated panel above and below the unit when rack-mounting.) Under 90% RH (no due condensation produced) Case: Pre-coated steel plate, black, 30% gloss 210 (W) × 53.3 (H) × 290 (D)mm 1.8kg CD-R (Software Decoder, Active X Control, Jet Manager, Manuals) × 1, AC power cord (2m) × 1, D-sub connector (9 pins, female) × 1 MB-15B-BK: For rackmounting two N-VT1010 units MB-15B-J: For rackmounting N-VT1010 unit * To be set on the Internet Explorer Recommended Personal Computer Personal Computer Main Specifications CS Required Browser PC/AT compatible (usable on a network) CPU: Pentium III, over 650 MHz Memory: Over 128 MB Display: High Color (16 bits), Graphic card capable of displaying over 1024 × 768 dots Windows 98SE/Me/2000/XP, Windows NT4.0 Service Pack 5 or later Internet Explorer 5.0 or later Notes: Pentium is a trademark of Intel Corporation. Windows and Windows NT are trademarks of Microsoft Corporation. Regarding other company names and products, they are also trademarks of individual companies. Provided as standard with each N-CC1000, N-CC1110 and N-VT1010 unit, the 1 channel software can be installed on a PC to enable network-based monitoring of images as well as controlling setting adjustments. Recommended Personal Computer CPU: Pentium III, over 650 HHz Memory: Over 128 MB Graphic card capable of displaying over 1024 × 768 dots Display: High Color (16 bits) CS: Windows 98SE/Me/2000/XP, Windows NT4.0 *Dedicated 1-channel software decoder for N-CC1000, N-CC1110 and N-VT1010. Network Camera System 1-CHANNEL SOFTWARE DECODER * Pentium is a trademark of Intel Corporation. * Windows and Windows NT are trademarks of Microsoft Corporation. 1. Install/connect the device. ▼ Included software: 1-channel software decoder Active X control Jet Manager Owner's manual (PDF), etc. 2. Install software. ▼ 3. Setup IP address using “Jet Manager”. ▼ 4. Select/adjust devices using the Internet Explorer browser. ▼ 5. Start monitoring using the “1 channel software decoder”. The supplied CD-ROM provides an easy to follow menu-driven guide. Main Screen •Image Setup Screen •Camera Setup Screen •Wide Dynamic Setup Screen N-VT1010's Combination Camera Operation Screen Activates Autofocus. Displays numbers entered Auto-focuses on. Sets zoom lens for Telephoto or Wide Angle. Sets zooming speed at Time-lapse, Low, Medium, or High. with the ten key pad. Controls Pan/Tilt motion. Sets one-push or continuous motion for Pan/Tilt operation. Ten key pad Starts/Stops auto-panning. Restart the camera. Displays the IP address and title of the transmitter currently connected. Sets focus speed at Time-lapse, Low, Medium, or High. Setup key Turns on/off Camera menu. CLEAR key Sets Pan/Tilt speed at Time-lapse, Low, Medium, or High. 18 1-CHANNEL SOFTWARE DECODER Network Camera System N-CC1000's setting General Sets up basic information such as ID, title, date and time, and version information. Network Sets up IP address, multicast, FTP, and E-mail. Video Sets up image quality, resolution, maximum transmission rate,and compression method. Camera Sets up basic function such as lens selection, wide dynamic function, backlight compensation, sensivity boost, white balance and etc. Alarm Sets up alarm trigger, alarm action, and alarm output. Serial port Sets up data transfer rate, data length, and parity ofthe serial port Normal Large Configuration Restart N-CC1110's setting General Sets up basic information such as ID, title, date and time, and version information. Network Sets up IP address, multicast, FTP, and E-mail. Video Sets up image quality, resolution, maximum transmission rate,and compression method. Alarm Sets up alarm trigger, alarm action, and alarm output. Serial port Sets up data transfer rate, data length, and parity ofthe serial port Normal Large Configuration Restart N-VT1010's setting General Sets up basic information such as ID, title, date and time, and version information. Network Sets up IP address, multicast, FTP, and E-mail. Video Sets up image quality, resolution, maximum transmission rate, and compression method. Alarm Sets up alarm trigger, alarm action, and alarm output. Serial port Sets up data transfer rate, data length, and parity of the serial port Normal Large Camera Control Configuration Restart N-SD1040 4-CHANNEL SOFTWARE DECODER SPECIFICATIONS Personal Computer Recomended Main Specifications CS Media Function SOFTWARE DECODER (OPTIONAL) The N-SD1040 Software Decoder software can be installed and used in a standard PC (personal computer). It permits simultoneous display of up to 4 images from LANconnected network cameras and a network video transmitter. 19 PC/AT compatible (usable on a network) CPU: Pentium 4, over 1.7 GHz Memory:Over 256 MB Display: High Color (16 bits), Graphic card capable of displaying over 1024 × 768 dots Windows 98SE/Me/2000/XP, Windows NT4.0 CD-R Establishment and cutoff of connections to the network camera and video transmitter Data rate setting Priority image setting Saving the displayed image to a HDD Alarm-operated connection Event (connections, alarm, etc.) logging Notes: 1. The PC to be used must be able to be connected to a network via a LAN interface card. 2. The processing capability of the PC to be used in conjunction with the software decoder must be correspondingly higher as transmission speeds or image sizes increase. Slower processsing speeds may cause delays. 3. The software decoder is only compatible with the Windows operating system, and is not compatible with either Macintosh or Unix operating systems. * Pentium is a trademark of Intel Corporation. * Windows and Windows NT are trademarks of Microsoft Corporation. * Regarding other company names and products, they are also trademarks of individual companies. N-SD1040 Network Camera System 4-CHANNEL SOFTWARE DECODER Configuration bar Configuration: Performs system, log-on and link configuration and language selection. Monitor: Magnifies on-screenimage. 4-Screen: Switches from 1screen to 4-screen display 1-Screen: Switches from 4screen to 1-screen display Archive: Allows checking of recorded images and alarm status. Alarm: Allows checking activated alarm. Toolbar Connect Connects the software decoder with a transmitter. Directory Selects a device to be connected. Disconnect Terminates connection. Resolution Selects image resolution and level of image quality. Security Changes password. Remote Configuration Configures remote transmitters. LAN Data Rate Changes network's data transmission rate. Record Records images onto PC currently in use. Stop Stops recording. Snapshot Records snapshots of images during operation or playback. Control/Dialog Changes Alarm Input and Relay Output settings. Displays the now-active camera number. Toolbar Performs connection, selection and configuration setup. Configuration bar Displays available space on the hard disk a nd the amount of memory in use. Allows controlling combination cameras and multi-switchers onscreen. •Pan, tilt and zoom operations focus on the object you want to zoom in. ∞ Press [ ] button to focus on a distant subject. Press [O] button to focus on a subject nearby. Moves Combination cameras to a predetermined position. Sets the zoom lens at telephoto ([+]) or wide-angle ([–]). Rotates the camera (Pan/Tilt) Sets the lens speed and rotating speed. When two or more Combination cameras are connected to the multi-switcher,you can select the camera to operate. Moves Combination cameras to a predetermined direct position. Auto Focus •Operating the multi-switcher •Creating configurations is easy. Directory From Pan/Tilt Camera menu, select Combination camera or multi-switcher. Details Transmitter information Combination Camera Control Panel or Multi-switcher Control Panel isdisplayed. 20 NETWORK CAMERA SYSTEM Network Camera System SYSTEM EXAMPLES 1. Combination Dome Camera (1 unit) 2. Combination Dome Cameras (4 units) Remote Controller C-RM500 Combination Dome Cameras C-CC554S Remote Controller C-RM500 Combination Dome Cameras C-CC554S C-QA40 Monitor Quad Adapter Monitor 4. When Combination Dome Camera and Remote Controller are separated by more than 1.2km. 3. Combination Dome Camera (16 units) Combination Dome Cameras C-CC554S max. 3km C-MS161D max. C-IF500 Remote Controller C-RM500 Combination Dome Cameras C-CC554S Multiplexer 16 C-IF500 Remote Controller C-RM500 Monitor CC-3331B Cable Compensator 5. Sensor-activated Dome Camera operation. Sensor max. 8 Combination Dome Cameras C-CC554S C-MS161D max. 8 Remote Controller C-RM500 RS-232C Multiplexer Sensor Monitor C-AL80 max. 8 max. 256 C-AL80 Alarm Unit C-AL80 21 Monitor C-CC351A C-CC354A DESCRIPTION FEATURES The wide dynamic range that is engineered into TOA DSP Color Cameras allow these extraordinary cameras to deliver a performance that goes well beyond the parameters of human eyesight. These cameras provide natural images that are very similar to what the human eye sees to make for easy and non-tiring viewing. This quality is maintained under adverse lighting conditions such as backlighting. And enhanced night vision capability is also built in with a high performance electronic sensitivity booster that ensures clear images in color even under unsatisfactory lighting conditions. ● Wide dynamic range Provides a new level of performance with natural looking images even in backlight condition. Wide Dinamic Range Color Camera WIDE DYNAMIC RANGE COLOR CAMERAS ● Backlight compensation Allows optimal viewing of dark areas in a backlight condition. ● Maximum 32X sensitivity booster Enables increasing sensitivity to take color images even in night conditions. ● 480-line high resolution (PAL /NTSC) ● Newly developed DSP ● Fully automatic operation mode shift ● Easy menu-driven setup 22 C-CC351A WIDE DYNAMIC RANGE COLOR CAMERAS Wide Dinamic Range Color Camera APPEARANCE AND DIMENSIONAL DIAGRAM 74 68 56.5 65 136.5 127.3 1800 37 25.3 18 2–1/4–20UNC • Wide dynamic range unit: mm Provides a new level of performance with natural looking images even in backlight conditions. • Backlight compensation Allows optimal viewing of desired areas in a backlight conditions. • Maximum 32X sensitivity booster Enables increasing sensitivity to take good images even in night conditions. • Newly developed DSP • Fully automatic mode shift • Easy menu-driven setup • AC MAINS operation SPECIFICATIONS (PAL) Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Required Illumination Automatic Electric Shutter Range Dynamic Range Shutter Speed Backlight Compensation AGC Sensitivity Up White Balance Mode Chroma Level Enhancer Level Character Display Lens Mount Auto-Iris Lens Output Operating Temperature Finish Dimensions Weight SPECIFICATIONS (NTSC) 230V AC 50/60Hz, 5W 1/3 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50.00Hz VBS 1.0V (p-p) 75Ω, BNC Internal/Line lock (phase adjustable) Horizontal: 480 lines, Vertical: 410 lines 48dB (AGC OFF) 1 lx (F1.2, 50 IRE), 0.5 lx (F0.8, 50 IRE) (sensitivity up: OFF) 0.032 lx (F1.2, 50 IRE), 0.016 lx (F0.8, 50 IRE) (sensitivity up: 32 times) 1:600 46dB (wide dynamic ON)* 1/50, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 OFF/backlight compensation/wide dynamic Auto/Fixed (0 – 18dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (Min – Max) Normal/Manual (soft – sharp) Up to 8 characters (alphanumeric) CS mount VIDEO input type/DC input type (4-pin connector, switchable) –10˚C to +50˚C Case: surface treated steel plate, sand gray 74 (W) × 65 (H) × 136.5 (D)mm 645g * Meets JEITA specifications. 23 Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Required Illumination Automatic Electric Shutter Range Dynamic Range Shutter Speed Backlight Compensation AGC Sensitivity Up White Balance Mode Chroma Level Enhancer Level Character Display Lens Mount Auto-Iris Lens Output Operating Temperature Finish Dimensions Weight 120V AC, 50/60Hz 5W 1/3 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, BNC Internal/Line lock (phase adjustable) Horizontal: 480 lines, Vertical: 350 lines 48dB (AGC OFF) 1 lx (F1.2, 50 IRE), 0.5 lx (F0.8, 50 IRE) (sensitivity up: OFF) 0.032 lx (F1.2, 50 IRE), 0.016 lx (F0.8, 50 IRE) (sensitivity up: 32 times) 1:500 46dB (wide dynamic ON)* 1/60, 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 OFF/backlight compensation/wide dynamic Auto/Fixed (0 – 18dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (Min – Max) Normal/Manual (soft – sharp) Up to 8 characters (alphanumeric) CS mount VIDEO input type/DC input type (4-pin connector, switchable) –10˚C to +50˚C Case: surface treated steel plate, sand gray 74 (W) × 65 (H) × 136.5 (D)mm 675g * Meets JEITA specifications. C-CC354A WIDE DYNAMIC RANGE COLOR CAMERAS Wide Dinamic Range Color Camera APPEARANCE AND DIMENSIONAL DIAGRAM 136.5 127.3 56.5 65 74 68 2–1/4–20UNC 37 25.3 18 • Wide dynamic range unit: mm Provides a new level of performance with natural looking images even in backlight conditions. • Backlight compensation Allows optimal viewing of desired areas in a backlight conditions. • Maximum 32X sensitivity booster Enables increasing sensitivity to take good images even in night conditions. • Newly developed DSP • Fully automatic mode shift • Easy menu-driven setup • 24V AC or 12V DC operation SPECIFICATIONS (NTSC) SPECIFICATIONS (PAL) Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Required Illumination Automatic Electric Shutter Range Dynamic Range Shutter Speed Backlight Compensation AGC Sensitivity Up White Balance Mode Chroma Level Enhancer Level Character Display Lens Mount Auto-Iris Lens Output Operating Temperature Finish Dimensions Weight 24V AC 50/60Hz or 12V DC 5W 1/3 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50.00Hz VBS 1.0V (p-p) 75Ω, BNC Internal/Line lock (phase adjustable) Horizontal: 480 lines, Vertical: 410 lines 48dB (AGC OFF) 1 lx (F1.2, 50 IRE), 0.5 lx (F0.8, 50 IRE) (sensitivity up: OFF) 0.032 lx (F1.2, 50 IRE), 0.016 lx (F0.8, 50 IRE) (sensitivity up: 32 times) 1:600 46dB (wide dynamic ON)* PAL: 1/50, 1/120, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 OFF/backlight compensation/wide dynamic Auto/Fixed (0 – 18dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (Min – Max) Normal/Manual (soft – sharp) Up to 8 characters (alphanumeric) CS mount VIDEO input type/DC input type (4-pin connector, switchable) –10˚C to +50˚C Case: surface treated steel plate, sand gray 74 (W) × 65 (H) × 136.5 (D)mm 440g * Meets JEITA specifications. Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Required Illumination Automatic Electric Shutter Range Dynamic Range Shutter Speed Backlight Compensation AGC Sensitivity Up White Balance Mode Chroma Level Enhancer Level Character Display Lens Mount Auto-Iris Lens Output Operating Temperature Finish Dimensions Weight 24V AC 50/60Hz or 12V DC 5W 1/3 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, BNC Internal/Line lock (phase adjustable) Horizontal: 480 lines, Vertical: 350 lines 48dB (AGC OFF) 1 lx (F1.2, 50 IRE), 0.5 lx (F0.8, 50 IRE) (sensitivity up: OFF) 0.032 lx (F1.2, 50 IRE), 0.016 lx (F0.8, 50 IRE) (sensitivity up: 32 times) 1:500 46dB (wide dynamic ON)* NTSC: 1/60, 1/100, 1/125, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 OFF/backlight compensation/wide dynamic Auto/Fixed (0 – 18dB)/OFF OFF, 2, 4, 6, 8, 10, 16, 24, 32 times ATW/AWB/Manual Normal/Manual (Min – Max) Normal/Manual (soft – sharp) Up to 8 characters (alphanumeric) CS mount VIDEO input type/DC input type (4-pin connector, switchable) –10˚C to +50˚C Case: surface treated steel plate, sand gray 74 (W) × 65 (H) × 136.5 (D)mm 440g * Meets JEITA specifications. 24 C-CC351A / C-CC354A Wide Dinamic Range Color Camera WIDE DYNAMIC RANGE COLOR CAMERAS New DSP Crucial to achieving the extremely wide dynamic range function is the new TOA proprietary DSP. Using sophisticated digital video processing allows electronically combining two separate images taken with different shutter speeds to result in one perfect image. High-speed shutter output Gain control Memory circuit CCD Synthesis Video output Low-speed shutter output Gain control Memory circuit Wide dynamic range The C-CC351A and C-CC354A camera series achieve a remarkable dynamic range . This reflects a performance level that is 32 times greater than conventional CCD cameras. The wide dynamic range allows optimizing an image by automatically adjusting both dark and light areas to ensure the targeted area has ideal contrast and visibility. TOA Wide Dynamic Range Method Conventional cameras employ a single speed of 1/60sec. when taking images. TOA’s Wide Dynamic Range Method makes use of two shutter speeds, one set at 1/120sec. and TOA Wide Dynamic Method CCD output CCD output Conventional Method variable time time high-speed shutter 1/60sec one that is variable from 1/120sec. to 1/4000sec. to take two images which are electronically combined to produce a single, high-quality image. low-speed shutter (1/120sec to 1/4000sec) 1/120sec 1/120sec 1/60sec Three modes cover dynamic range requirements. Normal is the default setting where the dynamic range is adjusted automatically as needed as when the camera detects a backlighting condition. High-speed shutter loses details of indoor. Low-speed shutter creates whiteout of outdoor. Electronically combining the images taken using both low-speed and high-speed shutter gives single clear image. 25 Manual splits the screen into 12 segments and allows the user to adjust the dynamic range for the most desired segments. Off is for when wide dynamic range adjustment is not desired or when using the backlight compensation. Backlight compensation Maximum 32 times sensitivity boost TOA's CCD cameras have been designed to overcome the problems that conventional CCD cameras experience. Most of these problems originate from trying to accurately focus when the area of coverage includes areas with varying brightness. Cameras in some cases are affected by the bright areas they are monitoring with the result that there are some hard to see dark areas. When backlight compensation mode is selected, the camera divides an image into 12 segmented areas (4/4), comparing the brightness in each area to automatically adjust the required amount of backlight compensation for the desired segments. A greater degree of control is allowed by setting backlight compensation for 3/4 which provides finer backlight control over the area most important. 2/4 offers the finest degree of control by applying 12-segment backlight compensation to just the lower half of the screen. 12 segmented areas (4/4) 12 segmented areas (3/4) Magnification sensitivity can now be increased as needed all the way up to x32 in steps of x2, x4, x6, x8, x10, x16, x24 and x32 to compensate for lighting conditions that may be unsatisfactory. Sensitivity is boosted automatically to the point where good images can be taken. A camera normally requiring a minimum illumination of 1 lx can now operate well at an illumination level as low as 0.03 lx. This amount of sensitivity boost will now allow night video surveillance in color. Wide Dinamic Range Color Camera FEATUERS * boosting sensitivity may increase the afterimage phenomenon as shutter speed is reduced. 12 segmented areas (2/4) When the backlight compensation function is on, the camera can compensate for the different contrast levels in the segmented areas. The user selects the image area that is most important for viewing by segments. The backlight function then works by adjusting light conditions concentrating on the selected image area. The selected area will be shown in the best possible condition, for more effective monitoring. Backlight compensation is automatically switched off when the wide dynamic range function is used. High resolution images TOA cameras provide a high horizontal resolution level of 480 lines for excellent image quality. Image without the sensitivity boost Fully automatic operation mode shift TOA wide dynamic range cameras allow shifting between modes automatically, smoothly transitioning from mode to mode. Backlight Compensation (Backlight condition) Sensitivity Boost AGC Normal (Low-light condition) (Low-light condition) (standard condition) Video signal level detection video signal level detection Wide Dynamic (Backlight condition) Contrast difference detection 26 C-CC351A / C-CC354A SETUP FOR CAMERA Wide Dinamic Range Color Camera Mode Selection Switch 1. Lens VIDEO/DC switch for selecting auto-iris lens types. For manual setup, TOA Wide Dynamic Range Color Cameras are equipped with mode selection switches for manual setup. Various setup and adjustments may be performed using an on-screen menu. 2. Lens AUTO/MANUAL switch to select between the auto-iris, fixed iris, or manual iris lens. 8 9 10 3. AGC switch for selecting auto gain control mode and sensitivity boost mode. 4. Backlight compensation switch for activating/deactivating the backlight compensation mode together with wide dynamic range mode. 5. ATW switch for operating the auto tracking white balance function as light sources require. 6. Flickering reduction switch adjusts shutter speed to eliminate fluorescent lighting-induced flickering. 7. Synchronization switch* allows synchroning to line* or internal synch. 8. Iris control Adjust the lens Iris 1 2 3 4 5 6 7 *synchronizing to line is not possible when the power line frequency is 50Hz for NTSC cameras and 60Hz for PAL cameras. 9. Vertical phase control 10. Menu setup keys for menu selection. Setup Screen Conveniently allows setting up a camera and making adjustments and parameter changes through a menu-driven setup procedure. L ENS SELECT S HUT T ER SPEED W I D E DY N A M I C B ACK L I GH T AGC • S ENS UP WH I T E B A L A N C E C H R OMA L E V E L ENHANCER C AME R A I D PRESET 6. WHITE BALANCE •provides selecting from 3 modes: ATW: changes white balance to match color temperature of the target area. AWB: conforms to initial white balance setting. Manual: allows adjusting white balance manually for specialized lighting sources. 7. CHROMA LEVEL •for adjusting chroma level to suit user preference. 8. ENHANCER •for adjusting image contours to suit user preferences. 9. CAMERA ID •for assigning up to 8 alphanumeric characters and symbols to identify a specific camera. Also allows where to display camera title onscreen. 10. PRESET •Allows resetting all functions and controls to default settings. Menu 27 1. LENS SELECT •for adjusting iris level to match lens type selected. 2. SHUTTER SPEED •adjusts shutter speed to optimize image quality depending on lighting conditions and image flicker. 3. WIDE DYNAMIC •optimizes image quality by automatically adjusting both dark and light areas to ensure the targeted area has ideal contrast and visibility in backlighted conditions. 4. BACKLIGHT •prevents an object from becoming too dark to be vlewed due to backlight. 5. AGC - SENS UP •allows setting AGC to automatic, constant on or off. Allows adjusting sensitivity boost from 2x to 32x or switching it off. COMPACT COLOR CAMERAS Lens is optional C-CV14-2 2X varifocal lens included C-CV24-2 2X varifocal lens included DESCRIPTION TOA's compact color cameras represent new approaches to high-performance and high-resolution cameras for CCTV applications, each camera having specific features and functions. Indoor type: C-CV14-CS (lens is optional) C-CV14-2 (with 2X varifocal lens) C-CV24-2 (with 2X varifocal lens) Outdoor type: C-CV44-3 (with 2X varifocal lens) FEATURES ● Easy power requirements TOA compact color cameras operate on 24V AC or 12V DC. ● High-performance CCDs Each camera incorporates a 1/4” CCD with a resolution of 380,000 pixels (NTSC) (PAL 440,000 pixels) resulting a high horizontal resolution that exceeds 480 lines (NTSC) (PAL 470 lines). ● 2X varifocal lens To easily allow on-site adjustment for the viewing angle, each camera is fitted with a 2X manual varifocal lens having an auto iris. C-CV44-3 Compact Color Cameras C-CV14-CS 2X varifocal lens included ● Wide-ranging view angles Optimal camera angle of view extends from 53.2 to a wide 105 degrees, enhancing coverage over a wide range for more effective monitoring (C-CV14-2 and C-CV24-2). ● Versatile enough to handle less than perfect lighting. To cope with varying lighting conditions, backlight compensation can be switched on or off as required. ● Flicker-free for easier viewing The cameras do not cause the image to deteriorate as often caused by fluorescent lighting. Annoying image flicker is eliminated for more effective monitoring. ● Focus adjustment switch for easy focusing To simplify focusing even without using the ND filter*, an adjustment switch is provided for foolproof focusing. Adjustment switch makes focusing simple. TOA Compact Cameras do not require an ND filter for adjusting focus. By just setting the focus adjustment switch on the camera to ON, the lens iris opens and a shallow depth of field is maintained. To achieve perfect ON OFF focus simply and easily, just set the adjustment switch ON, adjust focus and then set the switch OFF. *see next page for more feature information. 28 C-CV14-CS COLOR CAMERA APPEARANCE AND DIMENSIONAL DIAGRAM Left Side View 18 2–1/4–20UNC Compact Color Cameras 33.2 Top View Lens is optional 102.5 89.7 35.5 63.4 SPECIFICATIONS (PAL) Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Lens Mount Auto-Iris Lens Output Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option 62.7 • Specifically designed for use in indoor applications • Lens available separately from a range of lens options. Camera accepts any CS mounted lens. • 24V AC or 12V DC operation • Horizontal resolution exceeds 480 (NTSC) lines (PAL 470 lines) • Equipped with backlight compensation function • Flickerless operation for viewing ease • Adjustment switch for easy focusing without using an ND filter Right Side View Front View Rear View unit: mm SPECIFICATIONS (NTSC) 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50Hz VBS 1.0V (p-p) 75Ω, BNC connector Internal synchronization Horizontal: 470 lines (at center), Vertical: 410 lines (at center) 48dB 3 lx (F1.4, 350mV) ATW CS mount DC input type (4 pin connector) ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/50, 1/120), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: Surface-treated steel plate, light gray, paint Front cover: Zinc, light gray, paint 63.4 (W) × 62.7 (H) × 102.5 (D)mm 300g Camera mounting bracket Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Lens Mount Auto-Iris Lens Output Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, BNC connector Internal synchronization Horizontal: 480 lines (at center), Vertical: 350 lines (at center) 48dB 3 lx (F1.4, 50%) ATW CS mount DC input type (4 pin connector) ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/60, 1/100), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: Surface-treated steel plate, light gray, paint Front cover: Zinc, light gray, paint 63.4 (W) × 62.7 (H) × 102.5 (D)mm 300g Camera mounting bracket *Focus Adjustment and the ND Filter Iris and field of depth When adjusting focus, an important aspect is depth of field, actually the depth of the focus. The term depth is used is because we can describe it as being deep or shallow. If the in-focus area goes well into (long distance) the subject field is referred to as being deep. If the background area is not in focus but the subject field is in sharp focus, the field is referred to as being shallow. The depth of field will change depending on the focal length of the lens, the iris of the lens and the shooting distance. And in surveillance cameras, the lens iris has an effect on focusing. As the diagram makes clear, the wider the lens iris opening size, the shallower will be the depth of field. Depth of field is deep Why will correct focus set during the day go off at night? That’s because focus has not been precisely set. Shooting with an auto-iris lens, the amount of light during the day makes the lens iris opening stay small. This results in a deep depth of field. But as day turns to night, the lens iris opens to get more light, the depth of field is reduced and the focus goes off. To adjust the focus, it is necessary to open the lens iris and reduce the depth of field. When using an auto-iris lens, the ND filter must be used to approximate nighttime light conditions so that the lens iris stays open and depth of field is reduced before adjusting the focus. ND Filter * Neutral Density (ND) Filter: A filter which reduces light coming through the camera lens without any effect on the light’s color temperature. Depth of field is shallow * TOA Compact Cameras do not require the ND Filter for adjusting focus. C-CV14-2 COLOR CAMERA APPEARANCE AND DIMENSIONAL DIAGRAM 2–1/4–20UNC 18 38.5 Top View 63 54 62.5 Compact Color Cameras 134.3 2X varifocal lens included 45.5 Front View • Equipped with lens having a 53.2 – 105.1 degree horizontal viewing angle and a 39.8 – 77.4 degree vertical viewing angle • Specifically designed for use in indoor applications • 24V AC or 12V DC operation • Horizontal resolution exceeds 480 (NTSC) lines (PAL 470 lines) • Equipped with backlight compensation function • Flickerless operation for viewing ease • Adjustment switch for easy focusing without using an ND filter • Lens cover installs easily with single touch SPECIFICATIONS (PAL) Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option 76 Rear View Side View Bottom View unit: mm SPECIFICATIONS (NTSC) 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50Hz VBS 1.0V (p-p) 75Ω, BNC connector Internal synchronization Horizontal: 470 lines (at center), Vertical: 410 lines (at center) 48dB 3 lx (350mV) ATW f = 2.0mm – 4.0mm 1:1.4 – 1.8 Auto-iris Horizontal: 105.1° – 53.2°, Vertical: 77.4° – 39.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/50, 1/120), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: Surface-treated steel plate, light gray, paint Lens cover: ABS resin, light gray 63 (W) × 62.5 (H) × 134.3 (D)mm 300g Camera mounting bracket Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, BNC connector Internal synchronization Horizontal: 480 lines (at center), Vertical: 350 lines (at center) 48dB 3 lx (50 IRE) ATW f = 2.0mm – 4.0mm 1:1.4 – 1.8 Auto-iris Horizontal: 105.1° – 53.2°, Vertical: 77.4° – 39.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/60, 1/100), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: Surface-treated steel plate, light gray, paint Lens cover: ABS resin, light gray 63 (W) × 62.5 (H) × 134.3 (D)mm 300g Camera mounting bracket 30 C-CV24-2 COLOR DOME CAMERA 83.5 APPEARANCE AND DIMENSIONAL DIAGRAM Top View ø118 97 Compact Color Cameras Front View Bottom View without cover Bottom View 2X varifocal lens included unit: mm • Equipped with lens having a 53.2 – 105.1 degree horizontal viewing angle and a 39.8 – 77.4 degree vertical viewing angle • Specifically designed for use in indoor applications • 24V AC or 12V DC operation • Horizontal resolution exceeds 480 (NTSC) lines (PAL 470 lines) • Equipped with backlight compensation function • Flickerless operation for viewing ease • Adjustment switch for easy focusing without using an ND filter • Wide camera lens angle setting • Monitor output provided for connecting a display to make camera setting adjustments simpler CAMERA ANGLE SETTING RANGE (Rotating angle to vertical direction) Ceiling Front View (Rotating angle to horizontal direction) Bottom View 70 ° 105.1° – 53.2° (WIDE) (TELE) Angle of View (Horizontal direction) ° 70 77.4° – 39.8° (WIDE) (TELE) Angle of View (Vertical direction) 65 ° ° 65 Front (Image rotating angle) 90 ° SPECIFICATIONS (PAL) Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Monitor Output Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option SPECIFICATIONS (NTSC) 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50Hz VBS 1.0V (p-p) 75Ω, RCA pin jack VBS 1.0V (p-p) 75Ω, M3 screw terminal Internal synchronization Horizontal: 470 lines (at center), Vertical: 410 lines (at center) 48dB 3 lx (350mV) ATW f = 2.0mm – 4.0mm 1:1.4 – 1.8 Auto-iris Horizontal: 105.1° – 53.2°, Vertical: 77.4° – 39.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/50, 1/200), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: ABS resin, light gray Dome cover: Acrylic resin ø118 (W) × 97 (H)mm 370g Ceiling mounting bracket Note: No camera mounting screws are supplied. For mounting, use screws of 4 x 25mm or longer. 31 90 ° Bottom View without cover Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Monitor Output Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Operating Temperature Operating Humidity Applications Finish Dimensions Weight Option 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, RCA pin jackl VBS 1.0V (p-p) 75Ω, M3 screw terminal Internal synchronization Horizontal: 480 lines (at center), Vertical: 350 lines (at center) 48dB 3 lx (50 IRE) ATW f = 2.0mm – 4.0mm 1:1.4 – 1.8 Auto-iris Horizontal: 105.1° – 53.2°, Vertical: 77.4° – 39.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/60, 1/100), Iris control –10˚C to +50˚C Under 90% RH (no due condensation produced) Indoor use Case: ABS resin, light gray Dome cover: Acrylic resin ø118 (W) × 97 (H)mm 370g Ceiling mounting bracket Note: No camera mounting screws are supplied. For mounting, use screws of 4 x 25mm or longer. C-CV44-3 OUTDOOR COLOR CAMERA APPEARANCE AND DIMENSIONAL DIAGRAM (187) 249 269 Front window 1.5 70 120° Mounting bracket 4–ø6.5 ø10.5 76 90 ° Front View 2X varifocal lens included Sunshade Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Monitor Output Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Water Resistance Operating Temperature Operating Humidity Finish Dimensions Weight Accessories 97.6 ø50 Rear View Lens Side view where sunshade and front cover have been removed from unit • Equipped with lens having a 36 – 71.9 degree horizontal viewing angle and a 26.8 – 52 degree vertical viewing angle • Specifically designed to withstand outdoor use with a water-resistant and dust-resistant construction (IP-66) • 24V AC or 12V DC operation • Horizontal resolution exceeds 480 (NTSC) lines (PAL 470 lines) • Equipped with backlight compensation function • Flickerless operation for viewing ease • Adjustment switch for easy focusing without using an ND filter • Full camera positioning in 3 axes makes it easy to achieve the optimal camera position SPECIFICATIONS (PAL) 109 Side View rotatable ±90° 12 ° 90 Compact Color Cameras Top View ø92 Water-resistant cap Power supply/video composite cable (cable end not processed) Rear view where waterproof cap and mounting bracket have been removed from unit unit: mm SPECIFICATIONS (NTSC) 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 752 (H) × 582 (V) (440,000 pixels) 2:1 interlace Horizontal: 15.625kHz, Vertical: 50Hz VBS 1.0V (p-p) 75Ω, RCA pin jack VBS 1.0V (p-p) 75Ω, water-resistant connector Internal synchronization Horizontal: 470 lines (at center), Vertical: 410 lines (at center) 48dB 3 lx (350mV) ATW f = 3.0mm – 6.0mm 1:1.2 – 1.5 Auto-iris Horizontal: 71.9° – 36°, Vertical: 52° – 26.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/50, 1/120), Iris control Equivalent to IP-66 –10˚C to +50˚C Under 90% RH (no due condensation produced) Front cover, rear cover, sunshade: Aluminum, light gray, paint Mounting bracket: Stainless steel, light gray, paint ø92 × 249 (D)mm (excluding mounting bracket) 1.1kg Mounting bracket × 1, Cord with water-resistant cap (2m) × 1, Bracket mounting bolt (with washer), Insulating spacer × 2 Power Source Power Consumption Image Device Number of Effective Pixels Scanning System Scanning Frequency Monitor Output Video Output Synchronizing System Resolution S/N Ratio Minimum Illumination White Balance Mode Focal Length Maximum Aperture Ratio Iris Angle of View Control Switch Other Function Water Resistance Operating Temperature Operating Humidity Finish Dimensions Weight Accessories 24V AC, 50/60Hz or 12V DC 2W 1/4 type IT-CCD 768 (H) × 494 (V) (380,000 pixels) 2:1 interlace Horizontal: 15.734kHz, Vertical: 59.94Hz VBS 1.0V (p-p) 75Ω, RCA pin jack VBS 1.0V (p-p) 75Ω, water-resistant connector Internal synchronization Horizontal: 480 lines (at center), Vertical: 350 lines (at center) 48dB 3 lx (50 IRE) ATW f = 3.0mm – 6.0mm 1:1.2 – 1.5 Auto-iris Horizontal: 71.9° – 36°, Vertical: 52° – 26.8° ON/OFF (used for focus adjustment) Backlight compensation, Shutter speed (1/60, 1/100), Iris control Equivalent to IP-66 –10˚C to +50˚C Under 90% RH (no due condensation produced) Front cover, rear cover, sunshade: Aluminum, light gray, paint Mounting bracket: Stainless steel, light gray, paint ø92 × 249 (D)mm (excluding mounting bracket) 1.1kg Mounting bracket × 1, Cord with water-resistant cap (2m) × 1, Bracket mounting bolt (with washer), Insulating spacer × 2 32 Compact Color Cameras LENS SELECTION GUIDE ■ Focal Length of Lens and Field of View ■ Using the “Lens and Field of View” table To choose an appropriate lens, it is important to first understand the relationship between the focal length and field of view. When a camera and an object are set at a certain distance, a wide-angle lens with a shorter focal length can shoot a wider range in comparison, a telephoto lens with a longer focal length enlarges the image. A standard lens is in between these two. By gradually adjusting the focal length, a zoom lens achieves both wideangle and telephoto lens capabilities. Choose the appropriate lens by determining the required field of view. The table below lists the fields of view for lenses of cameras with 1/3" pickup element. Using this table, it is easy to determine the necessary field of view and appropriate lens (focal length). For example, to film a 10m (W) x 7.5m (H) area from a 6m camera distance, a lens with a 2.8mm focal length (f) is most suitable. There are two lenses, including the CT-0312G, with a 2.8mm or equivalent focal length, which will realize the approximate desired field of view. Field of View for 1/3" Pickup Element (“CS” Mount Lenses) Focal Length of Lens ■ Determining the Field of View from Focal Focal Length of Lens Length of Lens Field of View If the camera type (pickup element size) and focal length of lens details are known, the actual field of view can be determined by using the following formulas. Use the “Lens and Field of View” tables below to more easily determine the field of view. Distance Between Lens and Object Relationship between Focal Length of Lens and Field of View • Cameras with 1/3" pickup element 4.8 × L W = —– f • Cameras with 1/4" pickup element 3.6 × L W = —– f W (m) 2.7 × L H = —– f W: Width of the object H: Height of the object L : Distance to the object f : Focal length of lens H (m) 3.6mm 4mm 4.5mm 4.8mm Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. 0.5m 0.86 0.64 0.67 0.50 0.60 0.45 0.53 0.40 0.50 0.38 0.6m 1.03 0.77 0.80 0.60 0.72 0.54 0.64 0.48 0.60 0.45 0.7m 1.20 0.89 0.93 0.70 0.84 0.63 0.75 0.56 0.70 0.53 0.8m 1.37 1.02 1.07 0.8 0.96 0.72 0.85 0.64 0.80 0.60 1m 1.71 1.28 1.33 1.00 1.20 0.90 1.5m 2.57 1.92 2.00 1.50 1.80 2m 3.43 2.56 2.67 2.00 2.40 1.80 2.13 1.60 2.00 1.50 3m 5.14 3.84 4.00 3.00 3.60 2.70 3.20 2.40 3.00 2.25 4m 6.86 5.12 5.33 4.00 4.80 3.60 4.27 3.20 4.00 3.00 5m 8.57 6.40 6.67 5.00 6.00 4.50 5.33 4.00 5.00 3.75 6m 10.29 7.68 8.00 6.00 7.20 5.40 6.40 4.80 6.00 4.50 7m 12.00 8.96 9.33 7.00 8.40 6.30 7.47 5.60 7.00 5.25 8m 13.71 10.24 10.67 8.00 9.60 7.20 8.53 6.40 8.00 6.00 10m 17.14 12.80 13.33 10.00 12.00 9.00 10.67 8.00 10.00 7.50 15m 25.71 19.20 20.00 15.00 18.00 13.50 16.00 12.000 15.00 11.25 20m 34.29 25.70 26.67 20.00 24.00 18.00 21.33 16.00 20.00 15.00 30m 51.43 38.55 40.00 30.00 36.00 27.00 32.00 24.00 30.00 22.50 40m 68.57 51.40 53.33 40.00 48.00 36.00 42.67 32.00 40.00 30.00 50m 85.71 64.25 66.67 50.00 60.00 45.00 53.33 40.00 50.00 37.50 Distance Between Lens and Object 3.6 × L H = —– f 2.8mm Horiz. 0.80 1.00 0.75 Field1.07of View 1.35 1.60 1.20 1.50 [Horiz. (W)/Vert. (H)]1.13 60m 70m DC Input Type Auto-Iris Lenses Manual Iris Lenses f (mm) CT-0312G CT-0412G CT-0312 CT-041 Suitable Lens L (m) Field of View for1/3" Pickup Element (“CS” Mount Lenses) Focal Length of Lens Field of View 2.8mm 3.6mm 4mm 4.5mm 4.8mm unit: m 6mm 8mm 12mm Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. Horiz. Vert. 0.5m 0.86 0.64 0.67 0.50 0.60 0.45 0.53 0.40 0.50 0.38 0.40 0.30 0.30 0.23 0.20 0.15 0.15 0.11 0.6m 1.03 0.77 0.80 0.60 0.72 0.54 0.64 0.48 0.60 0.45 0.48 0.36 0.36 0.27 0.24 0.18 0.18 0.14 0.7m 1.20 0.89 0.93 0.70 0.84 0.63 0.75 0.56 0.70 0.53 0.56 0.42 0.42 0.32 0.28 0.21 0.21 0.16 0.8m 1.37 1.02 1.07 0.8 0.96 0.72 0.85 0.64 0.80 0.60 0.64 0.48 0.48 0.36 0.32 0.24 0.24 0.18 1m 1.71 1.28 1.33 1.00 1.20 0.90 1.07 0.80 1.00 0.75 0.80 0.60 0.60 0.45 0.40 0.30 0.30 0.23 1.5m 2.57 1.92 2.00 1.50 1.80 1.35 1.60 1.20 1.50 1.13 1.20 0.90 0.90 0.68 0.60 0.45 0.45 0.34 2m 3.43 2.56 2.67 2.00 2.40 1.80 2.13 1.60 2.00 1.50 1.60 1.20 1.20 0.90 0.80 0.60 0.60 0.45 3m 5.14 3.84 4.00 3.00 3.60 2.70 3.20 2.40 3.00 2.25 2.40 1.80 1.80 1.36 1.20 0.90 0.90 0.68 4m 6.86 5.12 5.33 4.00 4.80 3.60 4.27 3.20 4.00 3.00 3.20 2.40 2.40 1.80 1.60 1.20 1.20 0.90 5m 8.57 6.40 6.67 5.00 6.00 4.50 5.33 4.00 5.00 3.75 4.00 3.00 3.00 2.25 2.00 1.50 1.50 1.13 6m 10.29 7.68 8.00 6.00 7.20 5.40 6.40 4.80 6.00 4.50 4.80 3.60 3.60 2.70 2.40 1.80 1.80 1.35 7m 12.00 8.96 9.33 7.00 8.40 6.30 7.47 5.60 7.00 5.25 5.60 4.20 4.20 3.15 2.80 2.10 2.10 1.58 8m 13.71 10.24 10.67 8.00 9.60 7.20 8.53 6.40 8.00 6.00 6.40 4.80 4.80 3.60 3.20 2.40 2.40 1.80 10m 17.14 12.80 13.33 10.00 12.00 9.00 10.67 8.00 10.00 7.50 8.00 6.00 6.00 4.50 4.00 3.00 3.00 2.25 15m 25.71 19.20 20.00 15.00 18.00 13.50 16.00 12.000 15.00 11.25 12.00 9.00 9.00 6.75 6.00 4.50 4.50 3.38 20m 34.29 25.70 26.67 20.00 24.00 18.00 21.33 16.00 20.00 15.00 16.00 12.00 12.00 9.00 8.00 6.00 6.00 4.50 30m 51.43 38.55 40.00 30.00 36.00 27.00 32.00 24.00 30.00 22.50 24.00 18.00 18.00 13.50 12.00 9.00 9.00 6.75 40m 68.57 51.40 53.33 40.00 48.00 36.00 42.67 32.00 40.00 30.00 32.00 24.00 24.00 18.00 16.00 12.00 12.00 9.00 50m 85.71 64.25 66.67 50.00 60.00 45.00 53.33 40.00 50.00 37.50 40.00 30.00 30.00 22.50 20.00 15.00 15.00 11.25 24.00 18.00 Distance Between Lens and Object 60m 70m DC Input Type Auto-Iris Lenses Manual Iris Lenses 33 16mm CT-0312G CT-0412G CT-0812G CT-0312 CT-041 CT-0812 18.00 13.50 21.00 15.75 LENSES FOR CCTV CAMERAS Motorized Zoom Lenses CT-10ZMGA CT-21ZMG CT-2ZMGA CT-10VFG Lenses for CCTV Cameras CT-6ZMG Manual Zoom and Varifocal Auto Iris Lenses Auto Iris Lenses CH-3808G CH-2610G CT-0312GA CH-0808G Aspherical Lens Aspherical Lens CT-0412GA CT-0812GA Aspherical Lens Manual Iris Lenses CT-0312A CT-0412A CT-0812A FEATURES ● The flexible TOA CCTV lens range includes a manual iris lens, an auto iris lens and a motorized zoom lens as well as a pin-hole lens, making it simple to select the most suitable lens for any CCTV application. ● An auto iris lens allows using a much higher F number than possible with a conventional lens, increasing its effectiveness for use outdoors under bright, sunny conditions. ● An aspherical lens with a low minimum F number proves especially effective for low-light surveillance use. ● 21X motorized zoom lens offers high-magnification surveillance. Note: An aspherical lens cannot be used on a B/W camera. 34 Motorized Zoom Lenses (DC-input type) CT-6ZMG CT-10ZMGA 6 × Motorized Zoom Lens 10 × Motorized Zoom Lens (For 1/3" CCTV cameras) (For 1/3" CCTV cameras) 88 7.9 3.5 76.3 46 29.3 ø29.5 ø38 ø51 29.3 68.5 1–32UNF ø15 ø19.2 46 76.3 71.5 44.3 Lenses for CCTV Cameras Operating Temperature Weight Accessory Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Object Distance Flange Back Length Filter Size Lens Mount Tripod Connector Zoom Focus Operating Temperature Weight Accessory CT-21ZMG 21 × Motorized Zoom Lens (For 1/3" CCTV cameras) 126.5 105 47.4 ø30 ø45 79.5 44.5 1.5 12.5 1–32UNF ø65 70 53 12.5 (in air) L Automatic iris 4 wire cable (L=310) L Zoom/focus cable (L=450) Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Object Distance Flange Back Length Filter Size Lens Mount Tripod Connector Zoom Focus Operating Temperature Weight Accessory 35 12.5 (in air) L Zoom/focus cable (L=450) Unit: mm 5.7 – 34.2 mm 1: 1.0 4.8 (H) x 3.6 (V) mm Horizontal: 45.9° – 8.1° Vertical: 34.8° – 6.2° F1.0 – F360 ∞ – 1.2 m 12.5 mm M49 P = 0.75 CS mount 1/4–20UNC Control voltage: 6 VDC, under 20 mA Zooming speed: Approx. 3.5 s Control voltage: 6 VDC, under 20 mA Zooming speed: Approx. 3 s –10°C to +50°C 440 g Connector for focus (female) ··········1 Focus 1–32UNF L Automatic iris 4 wire cable (L=310) L Zoom/focus cable (L=450) Aperture Range Object Distance Flange Back Length Filter Size Lens Mount Tripod Connector Zoom 71.5 44.3 12.5 (in air) L Automatic iris 4 wire cable (L=310) Focal Length Maximum Aperture Ratio Image Format Size Angle of View 10.2 ø29.5 ø38 3.5 4.7 68.5 ø51 82.5 Unit: mm 5.8 – 121.8 mm 1: 1.6 4.8 (H) x 3.6 (V) mm Horizontal: 44.8° – 2.3° Vertical: 33.8° – 1.8° F1.6 – F560 ∞ – 1.5 m 12.5 mm M62 P = 0.75 CS mount 1/4–20UNC Control voltage: 6 VDC, under 40 mA Zooming speed: Approx. 4.5 s Control voltage: 6 VDC, under 40 mA Zooming speed: Approx. 5 s –10°C to +50°C 650 g Connector for focus (female) ··········1 5.7 – 57 mm 1: 1.2 4.8 (H) x 3.6 (V) mm Horizontal: 44.6° – 4.8° Vertical: 34.2° – 3.7° F1.2 – F560 ∞ – 1.8 m 12.5 mm M49 P = 0.75 CS mount 1/4–20UNC Control voltage: 6 VDC, under 20 mA Zooming speed: Approx. 4.5 s Control voltage: 6 VDC, under 20 mA Zooming speed: Approx. 4.5 s –10°C to +50°C 460 g Connector for focus (female) ··········1 Unit: mm Manual Zoom and Varifocal Auto Iris Lenses (DC-input type) CT-2ZMGA 2 × Varifocal Lens (For 1/3" CCTV cameras) 240 23.5 23.5 23 43.5 3.5 12.5 Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Operating Temperature Finish Dimensions Weight 3.5 – 8 mm 1: 1.4 – 1.8 4.8 (H) x 3.6 (V) mm Horizontal: 53.6° – 5.6° Vertical: 40.3° – 4.2° Opposite angle: 97.9° – 44.3° WIDE: F1.4 – F360 TELE: F1.8 – F360 0.4 m 13.1 – 8.3 mm 12.5 mm CS mount – 20°C to +50°C Black, matte 46.3 (W) x 38.6 (H) x 43.5 (D) mm 48 g Lenses for CCTV Cameras 23.3 ø30 ø38.6 ø33.5 1–32UNF CT-10VFG 10 × Varifocal Lens (For 1/3" CCTV cameras) 340 25 ø41 1–32UNF 33.2 25.5 59.2 4 12.5 (in air) Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Flange Back Length Lens Mount Operating Temperature Finish Dimensions Weight 5.0 – 50 mm 1: 1.4 – 2.0 4.8 (H) x 3.6 (V) mm Horizontal: 53.6° – 5.6° Vertical: 40.3° – 4.2° F1.4 – F180 ∞ – 1.0 m (∞ – 0.3 m when the Tele/Wide knob is set to W position) 12.5 mm CS mount – 10°C to +60°C Black, matte 41 (W) x 58.7 (H) x 59.2 (D) mm 95 g 36 Auto Iris Aspherical Lenses (DC-input type) CH-2610G CH-3808G Ultra-Wide-Angle Aspherical Lens Wide-Angle Aspherical Lens (For 1/3" CCTV cameras) (For 1/3" CCTV cameras) 7.99.6 21.8 15 21.8 1–32UNF Lenses for CCTV Cameras ø42 Aspherical Lens 3.5 55 ø54 * An aspherical lens cannot be used on a B/W camera. 5.2 12.5 (in air) Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View (1/3 inch) 2.6 mm 1: 1.0 6.4 (H) x 4.8 (V) mm Horizontal: 97.13° Vertical: 75.03° F0.8 – F360 0.1 m 8.5 mm 12.5 mm M43 P = 0.75 CS mount –20°C to +50°C Black 54 (W) x 61 (H) x 55 (D) mm 143 g Aperture Range Minimum Object Distance Back Focus Flange Back Length Filter Size Lens Mount Ambient Temperature Finish Dimensions Weight Aperture Range Minimum Object Distance Back Focus Flange Back Length Filter Size Lens Mount Operating Temperature Finish Dimensions Weight Standard-Angle Aspherical Lens (For 1/3" CCTV cameras) 21.8 Aspherical Lens 45.5 ø20.5 ø22.8 ø30 ø45.5 ø42 22.8 310 34 1–32UNF 43 3.5 5.2 12.5 (in air) * An aspherical lens cannot be used on a B/W camera. Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View (1/3 inch) Aperture Range Minimum Object Distance Back Focus Flange Back Length Filter Size Lens Mount Operating Temperature Finish Dimensions Weight 37 8 mm 1: 0.8 6.4 (H) x 4.8 (V) mm Horizontal: 34.0° Vertical: 25.6° F0.8 – F360 0.3 m 9.6 mm 12.5 mm M40 P = 0.5 CS mount –20°C to +50°C Black 45.5 (W) x 56.8 (H) x 43 (D) mm 120 g ø20.5 ø22.8 ø30 ø45.5 ø45 45.5 52.5 3.5 * An aspherical lens cannot be used on a B/W camera. Focal Length Maximum Aperture Ratio Image Format Size Angle of View (1/3 inch) CH-0808G 5.5 Aspherical Lens 22.8 310 27 310 ø20.5 ø22.8 ø30 ø45.5 34 34 1–32UNF 5.2 12.5 (in air) Unit: mm 3.8 mm 1: 0.8 6.4 (H) x 4.8 (V) mm Horizontal: 68.6° Vertical: 52.1° F0.8 – F360 0.15 m 9.07 mm 12.5 mm M43 P = 0.75 CS mount –20°C to +50°C Black 45.5 (W) x 56.8 (H) x 52.5 (D) mm 150 g Auto Iris Lenses (DC-input type) CT-0312GA CT-0412GA Ultra-Wide-Angle Lens Wide-Angle Lens (For 1/3" CCTV cameras) (For 1/3" CCTV cameras) Focus ring Focus ring 4 –core cable 7.8 43.5 310 1.6 36.8 Focus ring fixing screw 4 36.3 36.8 Focus ring fixing screw 12.5 21.1 1.6 ø34 ø15.1 ø36 43.5 310 ø33.9 4.6 ø15.1 ø36 7.1 21.1 7.8 33.8 4 12.5 Unit: mm 2.8 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 117.8° Horizontal: 94.3° Vertical: 71.5° F1.2 – F200 0.3 m 7.67 mm 12.5 mm CS mount –20°C to +50°C Black, matte 36.8 (W) x 43.5 (H) x 36.3 (D) mm 54 g Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Operating Temperature Finish Dimensions Weight Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Operating Temperature Finish Dimensions Weight 4 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 76.7° Horizontal: 63.9° Vertical: 49.2° F1.2 – F200 0.2 m 8.01 mm 12.5 mm CS mount –20°C to +50°C Black, matte 36.8 (W) x 43.5 (H) x 33.8 (D) mm 49 g Lenses for CCTV Cameras 4 –core cable CT-0812GA Standard-Angle Lens (For 1/3" CCTV cameras) Focus ring 1.6 ø15.1 ø36 43.5 310 21.1 ø34 4.6 36.8 Focus ring fixing screw 7.8 33.8 4 12.5 4 –core cable Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Operating Temperature Finish Dimensions Weight 8 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 41.4° Horizontal: 33.3° Vertical: 25.1° F1.2 – F200 0.3 m 7.73 mm 12.5 mm CS mount –20°C to +50°C Black, matte 36.8 (W) x 43.5 (H) x 33.8 (D) mm 44 g 38 Manual iris lenses CT-0312A CT-0412A Ultra-Wide-Angle Lens Wide-Angle Lens (For 1/3" CCTV cameras) (For 1/3" CCTV cameras) ø15.1 ø34 ø36.8 ø30 ø15.1 ø34 ø36.8 5.6 5.6 12.5 33.8 Lenses for CCTV Cameras 36.3 Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Ambient Temperature Finish Dimensions Weight 2.8 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 117.8° Horizontal: 94.3° Vertical: 71.5° F1.2 – Close 0.3 m 7.67 mm 12.5 mm CS mount –20°C to +50°C Black, matte ø36.8 x 36.3 mm 44 g Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Ambient Temperature Finish Dimensions Weight Standard-Angle Lens (For 1/3" CCTV cameras) ø30 ø15.1 ø34 ø36.8 4 5.6 12.5 Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View Aperture Range Minimum Object Distance Back Focus Length Flange Back Length Lens Mount Ambient Temperature Finish Dimensions Weight 39 8 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 41.4° Horizontal: 33.3° Vertical: 25.1° F1.2 – Close 0.3 m 7.73 mm 12.5 mm CS mount –20°C to +50°C Black, matte ø36.8 x 33.8 mm 34 g 12.5 Unit: mm Focal Length Maximum Aperture Ratio Image Format Size Angle of View CT-0812A 33.8 ø30 4 4 4 mm ±5% 1: 1.2 4.8 (H) x 3.6 (V) mm Opposite angle: 76.7° Horizontal: 63.9° Vertical: 49.2° F1.2 – Close 0.2 m 8.01 mm 12.5 mm CS mount –20°C to +50°C Black, matte ø36.8 x 33.8 mm 39 g CAMERA HOUSINGS/PAN & TILT HEADS MOUNTING BRACKETS Camera Housings C-CH100/C-CH100FH C-CH210FH CC-6000A Indoor use Outdoor use C-CH200/C-CH200FH Pan & Tilt Heads CC-5525 CC-5521 CC-5550A C-PH200 Outdoor use Camera Housings/Pan & Tilt Heads Mounting Brackets CC-6080DMS CC-6080DMW CC-6080DMB Indoor use C-BL20 Zoom lens mounting bracket Pan & Tilt Head Mounting Bracket CC-5050B Pan head controller Housing & Camera Mounting Bracket C-BC200K CC-4520 C-BC11 C-BC21 C-BC31 C-BC41 CC-4510 Remote Control Unit WH-4 CC-5011B CC-5111B CC-5120 CC-5131B C-BC100K C-BC200H C-BC100T 40 Selection Chart (Indoor Use) Cameras Lenses Camera Housings Pan & Tilt Heads Remote Controllers Auto iris Lenses Mounting Brackets Camera Mounting Brackets CT-0812GA CT-0412GA Indoor Camera Housing CT-0312GA CC-6000A C-BC11 Pan & Tilt Head CC-5521 C-BC41 Short Range C-CC351A Remote Control Unit CC-5011B C-BC31 + 24V AC Power Supply CC-5941B Camera Housings/Pan & Tilt Heads Mounting Brackets C-BC21 C-CC354A Auto iris Lenses Dome-shaped Camera Housing CH-2610G CC-6080DMB Pan & Tilt Head CH-3808G CC-5525 CH-0808G CC-6080DMS Long Range Remote Control Unit CC-5111B Camera Mounting Brackets WH-4 + CC-6080DMW Relay Box CC-5120 Manual Zoom and Varifocal Auto iris Lenses Wall Mounting Bracket CT-2ZMGA VV-4520 Pan Head CT-10VFG CC-5550A Pan Head Controller CC-5050B Wall Bracket CC-4510 Motorized Zoom and Varifocal Auto iris Lenses CT-6ZMG Zoom Lens Mounting Bracket CT-10ZMGA C-BL20 CT-21ZMG 41 Selection Chart (Outdoor Use) Cameras Lenses Camera Housings Auto iris Lenses Outdoor Camera Housing CH-2610G C-CH100 C-CH100FH CT-0312GA Pan & Tilt Heads Remote Controllers Mounting Brackets Wall Mounting Bracket C-BC100K C-CC351A Short Range Remote Control Unit CC-5011B + Auto iris Lenses 24V AC Power Supply C-CC354A C-BC100T Camera Housings/Pan & Tilt Heads Mounting Brackets CC-5941B CH-3808G Ceiling Suspension Bracket CH-0808G CT-0812GA Outdoor Pan & Tilt Head CT-0412GA C-PH200 Manual Zoom and Varifocal Auto iris Lenses CT-2ZMGA Long Range CT-10VFG Remote Control Unit Motorized Zoom and Varifocal Auto iris Lenses CC-5111B + Relay Box CT-6ZMG CC-5120 CT-10ZMGA CT-21ZMG Outdoor Camera Housing C-CH200 C-CH200FH Outdoor Camera Housing Housing Fixing Stand Wall Mounting Bracket C-BC200H C-BC200K C-CH210FH 42 Camera Housings C-CH100 The C-CH100 is a rainproof camera housing that protects the CCTV camera with a standard lens or zoom lens from the direct sunlight, wind and rain when installed outdoors. It can be suspended from a ceiling or mounted to a wall using the mounting bracket. Outdoor Camera Housing 154.5 70 SPECIFICATIONS Application Operating Temperature Operating Humidity Waterproof Function Dimensions Internal Capacity Weight Finish 159 128 ( 139 Length when the cover is fully opened 267 ) 2–M6 148 400 172 70 189.5 Accessories Option Camera Housings/Pan & Tilt Heads Mounting Brackets 2–M6 Unit: mm C-CH100FH General outdoor environments (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) –10°C to +45° Under 98% RH IEC529 IP33 172 (W) × 159 (H) × 400 (D) mm 80 (W) × 77 (H) × 305 (D) mm 2 kg Panel: Die-cast aluminum, light-beige, paint Other parts: Aluminum, off-white, paint Camera mounting screw × 1 set Ceiling suspension bracket: C-BC100T Wall mounting bracket: C-BC100K The C-CH100FH is a rainproof camera housing that protects the CCTV camera with a standard lens or zoom lens from the direct sunlight, wind and rain when installed outdoors. It comes with both a fan and heater, and can be suspended from a ceiling or mounted to a wall using the mounting bracket. Outdoor Camera Housing SPECIFICATIONS 154.5 70 Power Power Consumption Fan/heater operating temperature Application Operating Temperature Operating Humidity Waterproof Function Dimensions Internal Capacity Weight Finish 159 128 ( 139 Length when the cover is fully opened 267 ) 2–M6 148 400 172 189.5 70 Accessories Option 2–M6 Unit: mm C-CH200 24 V AC, 50/60 Hz 25 W Fan: Turns on at over 26°C Heater: Turns on at under approx. 10°C General outdoor environments (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) –10°C to +45° Under 98% RH IEC529 IP33 172 (W) × 159 (H) × 400 (D) mm 80 (W) × 77 (H) × 305 (D) mm 2.2 kg Panel: Die-cast aluminum, light-beige, paint Other parts: Aluminum, off-white, paint Camera mounting screw × 1 set Ceiling suspension bracket: C-BC100T Wall mounting bracket: C-BC100K The C-CH200 camera housing is designed to house a CCTV camera, fixed focal length lens, zoom lens and other components to protect them from the direct sunlight, wind and rain when they are installed outdoors. Outdoor Camera Housing SPECIFICATIONS Operating Temperature Operating Humidity Application Waterproof/Dustproof Capability Finish 500 207 192.5 Dimensions Weight Accessories ø185 195 70 6–M6 220 Applicable Camera (option) Applicable Lens (option) Option 100 120 Unit: mm 43 –10°C to +45° 30% to 98% RH Indoors and outdoors (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) IP54 Unit: Aluminum extrusion, off-white, paint Panel: Die-cast aluminum, off-white, paint 195(W) × 207(H) × 500(D) mm 5.2 kg Camera mounting bolt × 2, Housing fixing bolt × 4, Washer…1 set, Coaxial cable for internal wiring × 1, Zoom lens cable for internal wiring × 1, Camera power supply cable (for 24 V) for internal wiring × 1 C-CC300 series, C-CC150A, C-CB20LA All lenses except ultra-wide angle lenses and special lenses Housing fixing stand: C-BC200H Wall mounting bracket: C-BC200K Pan/tilt head: C-PH200 SPECIFICATIONS The C-CH200FH camera housing is designed to house a CCTV camera, fixed focal length lens, zoom lens and other components to protect them from the direct sunlight, wind and rain when they are installed outdoors. The C-CH200FH comes with a heater and a fan. Outdoor Camera Housing Power Source Current Consumption Fan/heater Operating Temperature Operating Temperature Operating Humidity Application Waterproof/Dustproof Capability Finish 500 207 192.5 Dimensions Weight Accessory ø185 195 Applicable Camera (option) Applicable Lens (option) Option 70 6–M6 100 120 220 C-CH210FH Unit: mm Power Source Current Consumption Fan/heater Operating Temperature Operating Temperature Operating Humidity Application Waterproof/Dustproof Capability Finish Dimensions Weight Accessory 192.5 207 500 6–M6 ø185 195 70 Applicable Camera (option) Applicable Lens (option) Option 100 120 220 Unit: Aluminum extrusion, off-white, paint Panel: Die-cast aluminum, off-white, paint 195(W) × 207(H) × 500(D) mm 5.4 kg Camera mounting bolt…2, Housing fixing bolt × 4, Washer…1 set, Coaxial cable for internal wiring × 1, Zoom lens cable for internal wiring × 1, Camera power supply cable (for 24 V) for internal wiring × 1 C-CC300 series, C-CC150A, C-CB20LA All lenses except ultra-wide angle lenses and special lenses Housing fixing stand: C-BC200H Wall mounting bracket: C-BC200K Pan/tilt head: C-PH200 SPECIFICATIONS The C-CH210FH camera housing is designed to house a CCTV camera, fixed focal length lens, zoom lens and other components to protect them from the direct sunlight, wind and rain when they are installed outdoors. The C-CH210FH is equipped with a heater, a fan, a defroster, and a wiper. Outdoor Camera Housing 24 V AC, 50/60 Hz Fan: 4.6 W Heater: 19 W Fan: Turns on at over 26°C Heater: Turns on at under 10°C -20°C to +45°C (If the wiper driving section is frozen, the wiper does not correctly work.) 30% to 98% RH Indoors and outdoors (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) IP54 Unit: mm CC-6000A 24 V AC, 50/60 Hz Fan: 4.6 W Heater: 19 W Defroster: 5W Wiper: 2.3 W Fan: Turns on at over 26°C Heater: Turns on at under 10°C Defroster: Turns on at under 30°C, and turns off at over 50°C –20°C to +45°C (If the wiper driving section is frozen, the wiper does not correctly work.) 30% to 98% RH Indoors and outdoors (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) IP54 Camera Housings/Pan & Tilt Heads Mounting Brackets C-CH200FH Unit: Aluminum extrusion, off-white, paint Panel: Die-cast aluminum, off-white, paint 195(W) × 207(H) × 500(D) mm 6 kg Camera mounting bolt…2, Housing fixing bolt × 4, Washer…1 set, Coaxial cable for internal wiring × 1, Zoom lens cable for internal wiring × 1, Camera power supply cable (for 24 V) for internal wiring × 1 C-CC300 series, C-CC150A, C-CB20LA All lenses except ultra-wide angle lenses and special lenses Housing fixing stand: C-BC200H Wall mounting bracket: C-BC200K Pan/tilt head: C-PH200 The CC-6000A is an Indoor use camera housing. Indoor Camera Housing 203 30 30 405 126 84 128 3–U1/4–20UNC SPECIFICATIONS Applications Operating Temperature Finish 86 Installation Example Unit: mm Dimensions Weight Applicable Cameras Applicable Lenses Indoors –10°C to +50°C Front frame, Top cover: ABS resin, light cream Base: Pre-coated steel plate, beige 128 (W) × 126 (H) × 405 (D) mm 1.7 kg 1/3 type series cameras 1/3 type series lenses and zoom lenses 44 Camera Housings Designed for mounting in the ceiling, TOA's CC-6080 Series is a dome-shaped camera housing capable of accommodating a black/white or color surveillance camera. CC-6080DMB/CC-6080DMW/ CC-6080DMS Dome-shaped Camera Housing 88 156 200 13 175 131.5 113.4 CC-6080DMB 87.4 Unit: mm (Tilt range when the ceiling board is 9 mm thick) θ 3˚ – 90˚ CAMERA C-CC300 series CC-6080DMW L max. 140 * The tilt angle narrows as the ceiling board increases in thickness. (The angles shown in the table above assume that the ceiling board is 9 mm thick.) Mounting diagram L max. Mounting ceiling hole diameter ø158 Co-axial cable Dust-proof net Fixing θ bracket Camera Housings/Pan & Tilt Heads Mounting Brackets Ceiling board Note: To mount the dome housing in the ceiling exceeding 25 mm in thickness, four bracket mounting screws with shank length equal to or greater than the ceiling thickness plus 10 mm are required extra. CC-6080DMS SPECIFICATIONS Tilt range As shown in the table below. (ceiling board is 9 mm in thickness.) Finish Dome: CC-6080DMB: Acryl, treated in part with masking paint, black CC-6080DMW: Acryl, treated in part with masking paint, white CC-6080DMS: Acryl, aluminum vacuum evaporation (penetration rate of 35% – 50%) Frame: ABS, ivory Bracket: Steel plate cold commercial, 1.2 mm thick plating, black Dimensions ø175 (W) × 156 (H) × 200 (D) mm Weight 520 g Applicable Lens CT-0313G, CT-0412G, CT-0812G Applicable Camera 1/3" camera series (made by TOA) Pan & Tilt Heads (Outdoor use) C-PH200 Enlarged view of housing mounting hole Housing mounting hole (Oval hole) 168 142 168 120 70 4–ø10 (for M8 bolt) 168 142 ø16 7 11.5 15 70 Outdoor Pan/Tilt Head R tion ight ro rota 175 tation Left 175˚ ˚ The C-PH200 is a rainproof and dustproof motorized pan/tilt head designed for both indoor and outdoor applications. Mounted with a camera housing containing CCTV camera and zoom lens, etc., the C-PH200 pan/tilt head can be rotated vertically and horizontally by remote control, thus greatly extending the camera’s range of surveillance capability. 46 93 259 Upwar rd d 20˚ wa wn Do 70˚ 68 25 SPECIFICATIONS Power Source Power Consumption Input/Output Lines Rotation Angle Operation Speed (No load) Rated Time Auto-Pan Life Load Rating Waterproof/Dustproof Capability Wind Pressure 2–7x80 housing mounting hole (for suspension) Application 10 180 282 199.4 Operating Temperature Operating Humidity Finish 84 131.6 Dimensions Weight Applicable Model Option 108 313 Unit: mm 45 24 V AC, 50/60 Hz 46 VA Video signal: Applicable cable diameter: ø4 – ø8 mm Screw terminal for 3C–2V or 5C–2V Power control: Applicable cable diameter: ø13 – ø18 mm M3 screw terminal (12 P) with free terminal screw x 2 Output line: Connected to the housing using dedicated cable Tilt: –70° to +20° ±5° Pan: Over 340° (automatic reverse), 350° ±5° (manual operation) Tilt: 3° ±0.5°/s (50 Hz), 3.6° ±0.6°/s (60 Hz) Pan: 6° ±0.5°/s (50 Hz), 7.2° ±0.6°/s (60 Hz) Tilt: 15 min, Pan: Continuous 5000 hours or 200000 reverse operations 11 kg (upright installation), 10 kg (indoor suspension) IP54 (Waterproof capability only applies to upright installation.) Operable at average wind velocity of 40 m/s or less. Not destructed at maximum wind velocity of 60 m/s (provided the unit is installed at a height of 15 m above the ground and C-CH200 Series camera housings are mounted) Indoors and outdoors (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure)* –10°C to +50°C (standard specifications and not frozen) 30% to 90% RH Die-cast aluminum and anti-corrosion aluminum plate, off-white, power coating 190(W) × 282(H) × 313(D) mm 10.2 kg Camera housing: C-CH200 series C-CH100 series Wall mounting bracket: C-BC200K *Because a waterproof function is disabled, unit cannot be installed in a suspended position outdoors. Pan & Tilt Heads (Indoor use) The CC-5525 Pan and Tilt Head is light-duty unit for CCTV camera, designed for long, quiet operation with loads up to 3kg. Auto-pan or manual pan operation is determined by the remote control box. CC-5525 Indoor Pan and Tilt Head 2–ø7 7 mm Wide oval hole 55–71 102–118 47 93 Load Rating Service Space Operation Temperature Operation Humidity Finish 35 49 185 225 36 .) 60˚ .W (C . .C N UP W.) ˚ (C 60 DOW 100 60 Limit Switch Stops Speed 6.5 Turn mark (red) Power Source Power Consumption Angular Travel 90 108 127 .) .W .C (C 0˚ L 17 70–86 100 47 A SPECIFICATIONS 4–ø7 Note: 1) Part A (Tilt Head) can be attached upside down for inverted mounting use. 2) Camera Mounting Table can be shifted sidewise by 16 mm for camera width adjustment. Weight Accessory Unit: mm CC-5521 24 V AC 4 VA max. Pan: 330° ±5° max. (auto pan), 340° ±5° max. (manual) Tilt: –60° to +60° Externally adjustable stops Pan: 4°/s (50 Hz), 4.8°/s (60 Hz) Tilt: 2°/s (50 Hz), 2.4°/s (60 Hz) 3 kg max. Indoor –5°C to +45°C 95% or below, relative humidity External body material: Die-cast aluminum alloy and Moulded plastic Three-tone (milky-white, off-white and black) 2.4 kg Terminal lug × 15, Plug (AC power output) × 1, Coaxial cable (530 mm) with BNC connectors on both ends × 1, 4-pin connector (zoom lens control) × 1, Camera attaching bolt × 2, Camera mounting table fixing screw × 2, Spring washer (ø6 mm) × 2, Plain washer (ø6 mm) × 2 The CC-5521 indoor pan and tilt head can be used to rotate and elevate a CCTV camera weighting up to 11kg under normal mounting conditions, or a camera weighting up to 10kg that is hung from a ceiling . The CC-5521 provides remote control camera travel of 350° pan and 65° up-down tilt. Limiting cams for both pan and tilt are externally adjustable. Auto-pan is also provided on the CC-5521. Indoor Pan and Tilt Head SPECIFICATIONS 120±2 20 165±2 142±0.5 7.5 165 142 Left Right 70 10 145 ø7.5dia 145 Cable entry port 10 4–ø10 2–ø10 80 Usable place Power Requirements Power Consumption Load Rating View on arrow A 4–M4 Tapped holes Max.65˚ Rubber sheet (insulator) Up 140 260±3 200±2 60 Max.65˚ 100 Down 4 32 8 9 10 6 11 5 7 3 ø165±2 1. Flanged base 2. Terminal cover 3. Main body cover 4. Camera mount 5. Connector cover 6. Connector plate 7. Pan limit cam 8. Tilt limit cam 9. Cable entry bushing 10. Zoom lens connector (MAB 4100) 11. Coaxial cable connector Ambient Temperature Ambient Humidity Main Skin Material Finish 1 A Weight Angular Travel 2 Speed Unit: mm CC-5550A The CC-5550A Pan Head is a light duty unit for CCTV cameras, design for long, quiet operation with loads up to 3kg. Pan operation is determined by the CC-5050B “Pan Head Controller”. 12 Indoor Pan Head 50˚ 30˚ Indoor 24 V AC ±10%, 50/60 Hz, single phase 40 VA (max.) Upright mounting: 11 kg Inverted mounting: 10 kg Based on C.G. to the camera mount center distance of 70mm and off center displacement of 25mm The tilting function may not work beyond the limited distances. (C.G. = center of gravity) –10°C to +45°C 95% or less, relative humidity Corrosion resistant aluminum sheet, cast aluminum alloy, synthetic resin (ABS) Metal part: Munsell 2.5YG/1 approx. value, (beige), leatherette and semi-glossy black texture Resin part: Munsell 5Y8/1 approx. value (ivory yellow), leatherette texture Approx. 5 kg Pan: 350° or more (manual), 345° (auto-pan) Tilt: –60° to +65° Pan: 6°/s (50Hz), 7.2°/s (60Hz) Tilt: 3°/s (50Hz), 3.6°/s (60Hz) Camera Housings/Pan & Tilt Heads Mounting Brackets 17 0˚ (C . R W.) 127 108 250 SPECIFICATIONS 1.6 150 Power Requirement Service Space Ambient Temperature Ambient Humidity Load Rating Angular Travel 67.5 44.5 15.5 ø52 76 127.5 18 127 108 26 8 Speed Life U1/4 TAPPED HOLE (10 mm deep) M4 TAPPED HOLE (10 mm deep, 4 places) 60 70 26 127 108 4–ø4.5 26 4–ø7 1.6 Ceiling flange dimensions Unit: mm Finish Weight Accessories 6V DC Indoor -5°C to +45°C Less than 95% (Relative humidity) Max. 3 kg (6.61 lb.) (Stand or Suspension) Pan 340° ±5° max. (Adjustable using external adjuster) 6°/s ±0.5°/s 8,000 hours (continuous operation when 60% of rated load is mounted) or 100,000 motions in both ways. Leather-tone 0.9 kg (1.98 lb.) Ceiling flange…1, Plain washer…1, Spring washer…1, Camera mounting screw…1, Hexagon headed bolt for mounting main body…1, Pan head screw (spring washer) M4 x 12 for mounting ceiling flange…4, Solderless terminal for I/O cable connection…6 46 Housing Mounting Brackets C-BC100K The C-BC100K is a bracket to mount the camera housing C-CH100 and C-CH100FH to a wall. Since it is made of stainless steel, it can be used even outdoors. 275 Wall Mounting Bracket 25 SPECIFICATIONS 70 Permissible Load Application 110 70 100 46 120 15 110 150 Angle Adjustment 150 4–ø8.5 170 Camera Housings/Pan & Tilt Heads Mounting Brackets Unit: mm C-BC100T Finish Dimensions Weight Usable Housing Under 10 kg Indoor or outdoor wall surface (exclude sea shores and industrial zones where the equipment easily becomes corroded, and the altitudes exposed to the strong wind) Horizontal: 360° (Four bolt mounting holes are provided to permit the position of bolt to be changed.) Vertical: Up 15°—down 60° (depending upon the horizontal angle, the unit may not be tilted 60° down) Stainless steel, off-white, paint 170 (W) x 250 (H) x 275 (D) mm 1.8 kg C-CH100 and C-CH100FH The C-BC100T is a bracket to mount the camera housing C-CH100 and C-CH100FH to a ceiling. Since it is made of stainless steel, it can be used even outdoors. Ceiling Suspension Bracket 80 100 80 4–ø8.5 30 Permissible Load Application 200 SPECIFICATIONS Angle Adjustment ø31.8 65 Finish Unit: mm C-BC200H The C-BC200H Housing Fixing Stand is designed to be used in conjunction with the wall-mounting bracket to mount camera housings on a wall to fix cameras in the predetermined direction. The C-BC200H is constructed of stainless steel and is designed to withstand prolonged use in severe outdoor environments without corrosion or marring of the unit’s appearance. Housing Fixing Stand 70 15 100 136 16 120 7 18 Dimensions Weight Usable Housing Under 10 kg Indoor or outdoor wall surface (exclude sea shores and industrial zones where the equipment easily becomes corroded, and the altitudes exposed to the strong wind) Horizontal: 360° Vertical: ±60° Bracket:Stainless steel, off-white, paint Pipe: Stainless steel 100 (W) × 295 (H) × 100 (D) mm 830 g C-CH100 and C-CH100FH Dimension for mounting hole 6–ø7 108 119.2 105 SPECIFICATIONS 100 60 ˚ Angler Adjustment 20˚ Applications ø70 Finish Dimensions Weight Accessory 120˚ Unit: mm 47 Applicable Model Option Vertical: –60° to +20° Horizontal: ±60°(120°) when using 2 mounting holes (Can be set freely for up to 360° when C-BC200K is mounted) Outdoor (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) Stainless steel (SUS304), off-white, paint 119.2(W) x 108(H) x 136(D) mm 900 g Wall mounting bracket mounting bolt (with washer, SUS)…2 Camera housing: C-CH200 series, C-CH100 series Wall mounting bracket: C-BC200K Pan&Tilt Head Mounting Brackets C-BC200K The C-BC200K Mounting Bracket is designed specifically for use in the wall-mounting of camera systems comprising the camera housing in combination with either the Pan/Tilt Head or the Housing fixing Stand. The C-BC200K is constructed of stainless steel and is designed to withstand prolonged use in severe outdoor environments without corrosion or marring of the unit’s appearance. Wall Mounting Bracket 313 288 142 4–M8 (for pan/tilt head mounting) 121 174 142 70 70 4–M6 (for housing fixing stand mounting) 405 2–10.5 x 15 (for M8, M10 or W3/8 bolt) SPECIFICATIONS 20 475 150 185 Permissible Load Wind Load Application 11 Finish Weight Accessory Option Unit: mm CC-4520 Under 20 kg Maximum wind velocity 60 m/s (When C-CH200 or C-CH100 Series and C-PH200 are used) Outdoor (except seaside and industrial districts where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure) Stainless steel (SUS304), off-white, paint 2.8 kg Pan/tilt head mounting bolt (SUS)…2 Pan/tilt head mounting washer (SUS) …1 set Pan/tilt head: C-PH200, CC-5521 Housing fixing stand: C-BC200H The TOA wall bracket model CC-4520 is used when pan/tilt head (model CC-5521) is fixed on the wall. Wall Mounting Bracket Camera Housings/Pan & Tilt Heads Mounting Brackets 228 200 4–10 x 14 Slotted hole for M8 bolt (for CC-5521) 184 142 182.8 142 343 4–ø11 Hole for M8–M10 or W3/8 bolt (for ceiling mounting) 166 142 142 40 SPECIFICATIONS Service Space Load Rating Applicable Model Finish Weight Accessory (21.6) 68.8 (182.6) 19 445 Unit: mm CC-4510 Indoor 10 kg max. CC-5521 Zinced steel plate, milky white, leather tone, paint 3.2 kg For assembling wall bracket: M6 × 12 Hex-head bolt, Plain washer and Spring washer × 6 sets, M4 × 10 Round head screw with washer × 1 set For mounting pan-tilt head: M8 × 20 Hex-head bolt, Nut and washer × 4 sets, Plain washer × 8 The TOA wall bracket model CC-4510 is used when pan or pan/tilt head (model CC-5525, CC-5550A) is fixed on the wall. Wall Bracket Cable inlet hole (ø18) 108 127 127 108 4–M6 Tapped hole (for CC-5525 or CC-5550A) 343.5 280 110 SPECIFICATIONS 40 127 108 25.4 173.5 8 8 108 127 4–ø7 Hole (for wall mounting) INSTALLATION EXAMPLES Service Space Load Rating Applicable Models Finish Weight Accessory Unit: mm Indoor 7 kg max. CC-5525, CC-5550A Flange: Casted aluminum, off-white, leather tone Pipe: Rigid steel conduit, off-white, semi-glazed 800 g M6 x 16 Hex-head bolt, Plain washer and Spring washer…4 sets 48 Camera Mounting Brackets C-BC11 The easy-to-install C-BC11 extendable ceiling bracket allows for insertion of the coaxial cable through the bracket pipe for an attractive appearance. Camera Mounting Bracket C-BC41 This bracket is used to install a camera and housing onto a ceiling. The coaxial cable can be inserted through the bracket pipe for an attractive appearance. It allows for 360° horizontal and 90° vertical angles of adjustment. Camera Mounting Bracket U1/4 camera screw 4–ø7 min. 305 36 U1/4 camera screw min. 617 ø28 5.5 15 ø25 5.5 4–ø7 36 83.5 ø25 83.5 ø28 ø36 15 11 t1.6 66.7 t1.6 ø120 66.7 ø120 Unit: mm Unit: mm SPECIFICATIONS SPECIFICATIONS Applications Permissible Load Angle Adjustment Indoor use 4 kg Horizontal: +90° to –15° Vertical: 360° Pipe: Aluminum, painted metallic silver Camera pedestal: ABS resin, sand gray Other parts: metallic silver 360 g Fixing screw × 4 Finish C-BC21 Camera Mounting Bracket The C-BC21 allows for quick and easy installation of a camera and camera housing onto a wall with 360° horizontal and 90° vertical angles of adjustment. The coaxial cable can be inserted through the bracket pipe for an attractive appearance. Finish Weight Accessory WH-4 Camera Mounting Bracket Indoor use 4 kg Horizontal: +90° to –15° Vertical: 360° Pipe: Aluminum, painted metallic silver Camera pedestal: ABS resin, sand gray Other parts: metallic silver 520 g Fixing screw × 4 This bracket allows easy installation of a CCTV camera and CC-6000A indoor camera housing on to a wall. The maximum bracket load is 10kg. U1/4 camera screw ø36 84 204 11 A 40 60 5.5 Camera Housings/Pan & Tilt Heads Mounting Brackets Weight Accessory Applications Permissible Load Angle Adjustment 4–ø7 270 250 ø25 83.5 242 36 15 View from A 66.7 t1.6 ø120 Unit: mm Applications Permissible Load Angle Adjustment Indoor use 4 kg Horizontal: +90° to –15° Vertical: 360° Pipe: Aluminum, painted metallic silver Camera pedestal: ABS resin, sand gray Other parts: metallic silver 340 g Fixing screw × 4 Finish Weight Accessory C-BC31 Camera Mounting Bracket 58 SPECIFICATIONS The bracket allows easy ceiling installation of a camera and camera housing. The coaxial cable can be inserted through the bracket pipe for an attractive appearance. Once installed, the camera can be adjusted 360° horizontally and 90° vertically. 130 6 2–ø7 36 ø25 15 ø36 U1/4 camera screw 5.5 t1.6 83.5 ø120 Unit: mm SPECIFICATIONS Applications Permissible Load Angle Adjustment Finish Weight Accessory 49 Indoor use 4 kg Horizontal: +90° to –15° Vertical: 360° Pipe: Aluminum, painted metallic silver Camera pedestal: ABS resin, sand gray Other parts: metallic silver 240 g Fixing screw × 2 115 199 Unit: mm SPECIFICATIONS Type Maximum Load Panning Angle Weight Ceiling/Wall mounting 10 kg Horizontal: 360° Vertical: 90° 930 g Zoom Lens Mounting Bracket 150 C-BL20 88.3 55 75 67 40 Zoom Lens Mounting Bracket 7 x 15 10 67 75 83 86.8 14 x 25 SPECIFICATIONS 10 1.6 – 12 32.5 62.3 2–U1/4–20UNC Head mounting hole Finish Weight Accessories 98 144 (4.49") 25.4 2 – 3.2 x15 14.4 4 The C-BL20 zoom lens mounting bracket is used for securely reinforcing to mount the camera with a zoom lens, and for mounting this camera and zoom lens on the pan/tilt head. Unit: mm Applicable Cameras Applicable Lenses Applicable Heads Aluminum t4.0 sand gray 160 g (0.35 lb.) Camera mounting (U1/4 – 20UNC bolt) × 1 M6 washer × 1 1/3" series cameras CT-8ZMG, CT-P8XMG, CT-P12ZMG CC-5521, CC-5525 CC-5050B The TOA CC-5050B Pan Head Controller permits to remotely control up to three CC-5550A pan heads. 1800 Pan Head Controller SPECIFICATIONS Power Requirement 44.5 47 Power Consumption Control Output Control Facilities 210 Operating Temperature Finish 231 246 Unit: mm Dimensions Weight Accessory HH: 220/240 V AC, 50/60 Hz L: 120 V AC, 50/60 Hz 4 VA DC 6 V, 100 mA max. M3 screw terminal, distance between barriers: 6 mm Panning (Left/Right/Auto) Pan head selection (3 pan heads) Remote input (Pan head selection 1 to 3 panning [Left/Right/Auto]) Remote output (Pan head selection 1 to 3 panning [Left/Right/Auto]) -10°C to +50°C Panel: Aluminum extrusion, black, 30% glossy Case: Pre-coated steel plate, black, 30% glossy 210 (W) × 47 (H) × 246 (D) mm 2 kg Fuse (0.5 A) × 1 Camera Housings/Pan & Tilt Heads Mounting Brackets Pan Head Controller 50 Remote Control Units (short range) CC-5011B The TOA's CC-5011B remote control unit is designed for highly effective observation from a short distance away. The CC-5011B provides the convenience of direct 24V AC operation when used in combination with the CC-5941B 24V power supply unit. At the touch of a remote control switch you have complete command auto/manual & left/right pan, tilt, zoom, focus and iris settings. The remote control unit can be mounted on a standard rack cabinet. Remote Control Unit SPECIFICATIONS 6 44.5 Power Input Main Power: 356 420 Housing Power: Control Output Control Motorized Pan/Tilt Unit: Camera Housing: Camera Power: Motorized Zoom Lens: Operating Temperature Finish 253 CC-5941B Pan (RIGHT/LEFT/AUTO), TILT (UP/DOWN) Defroster (ON-OFF), Wiper (ON-OFF) ON-OFF Zoom (WIDE/TELE), Focus (FAR/NEAR), Iris ( CLOSE/OPEN) Indoor use, –10°C to +50°C Panel: Aluminum extrusion, black, 30% gloss Case: Pre-coated steel plate, black, 30% gloss 420 (W) x 47 (H) x 253 (D) mm 3.3 kg 1-size rack-mounting bracket: MB-15B CC-5941B The CC-5941B is an adaptor supplies power to up to ten 24V AC camera or the 24V AC power to the CC-5011B shortdistance remote control unit for a CCTV camera system. 1800 24 V AC Power Supply SPECIFICATIONS Power requirement Power Consumption 210 Output Power 96.5 88.5 Camera Housings/Pan & Tilt Heads Mounting Brackets Unit: mm Dimensions Weight Option Power Supply Unit 24V AC, 50/60Hz (for motorized Pan/Tilt unit, camera power supply and motorized zoom lens) 24V AC, 50/60Hz (for camera housing) Make-contact for each control Operating Temperature Finish 231 210 Dimensions Weight Accessory Option Unit: mm AC Mains, 50/60Hz 135W (When operating camera, motorized zoom lens, pan/tilt unit, fan, heater and defroster.) 24V AC, 5A, 50/60Hz for camera and remote control unit M4 screw terminal, distance between barriers: 8.8mm Indoor use, –10°C to +50°C Panel: Aluminum extrusion, black, 30% gloss Case: Pre-coated steel plate, black, 30% gloss 210 (W) × 97.5 (H) × 231 (D) mm 4.1 kg Fuse (2A) × 1 1-size rack-mounting bracket: MB-23B-BK 2-size rack-mounting bracket: MB-23b-J SYSTEM BLOCK DIAGRAM Camera Housing Motorized Pan & Tilt Unit Remote Control Unit Power Supply CC-5011B CC-5941B Bracket *Maximum cable length and the number of cables may vary depending on the equipment to be connected and the type of cable. 51 Short-Distance Remote Control Camera Housing Motorized Pan & Tilt Unit Control line (A) Remote Control Unit Power Supply CC-5011B CC-5941B Bracket Table: 1: Required number of cables for long range remote control systems Example Coaxial cable Cable diameter and max. cable length (m) Housing Pan/tilt head Remote controller For Camera For pan/tilt head For housing For motorized zoom lens For video signals ø12 ø16 CT-6ZMGA CT-21ZMGA C-CC354A CT-10ZMGA + C-BL20 — CC-5525 CC-5011B 3 (2) 7 (6) — 3 1 250 450 2 CT-6ZMGA C-CC354A CT-21ZMGA CT-10ZMGA CC-6000A CC-5521 CC-5011B 0 7 (6) — 3 1 80 140 3 CT-6ZMGA C-CC354A CT-21ZMGA C-CH100FH CT-10ZMGA C-PH200 CC-5011B 0 7 (6) 2 3 1 40 75 CT-6ZMGA C-CC354A CT-21ZMGA C-CH210FH CT-10ZMGA C-PH200 CC-5011B 3 (2) 7 (6) 4 3 1 40 70 Camera 1 Indoor Motorized zoom lens Outdoor 4 Camera Housings/Pan & Tilt Heads Mounting Brackets Required number of cables between pan/tilt head and relay box (A) Unit combination 1. Depending on the combination units of functions in the system, the number of cables between the pan/tilt head and remote controller can be reduced, or cables can be jointly connected. For further information, refer to Table2. 2. Because maximum cable extension is determined at an ambient temperature of 20°C. it is recommended that thicker cables than those shown above be used. The stated maximum length can be made 1.5 times longer by using two common (COM) cables. 3. It is recommended to provide extra wiring for future system expansion or cable disconnection. 4. When using the CC-5525 pan/tilt head, the CC-50111B remote controller needs to be internally modified, otherwise, the auto-pan function cannot be operated. For further information, please contact the TOA office or TOA dealer in your country or region. 5. When suspending a pan/tilt head, reverse both upper/lower and left/right connections of the CC-5120 relay box and CC-5011B remote controller. For further information, please contact the TOA office or TOA dealer in your country or region. 6. Depending on the circumstances of installation, an earth cable for cameras and pan/tilt heads must used. 7. A camera, pan/tilt head and housing can share the AC-COM cable, but some of them may need connection wires for their internal connections. Table 2 For camera For pan/tilt head For housing For motorized zoom lens CAMERAUP UP AC-COM IRIS AC-COM DOWN WIPER FOCUS (Earth) RIGHT DEF ZOOM LEFT 0N-AC DC-COM AUTO AC-COM (Earth) 1. The AC-COM cable for cameras, pan/tilt heads and housings can be commonly used. However, depending on the combination of units in the system, the units need be bridged. 2. When using a motorized autp-iris zoom lens, it is possible to make connections using three wires omitting IRIS. 52 Remote Control Units (long range) CC-5111B The TOA's CC-5111B remote control unit and CC-5120 relay box provide highly effective surveillance from even a long distance away. The CC-5111B is designed for use with the CC-5120 and can control the housing defroster and wiper, pan/tilt head and motorized zoom lens remotely. The CC-5120 can supply the power to the camera, housing pan/tilt head and zoom lens. The remote control unite can be mounted on a standard rack, while the relay box is a wall mounting type. Remote Control Unit (required CC-5120 relay box) 44.5 SPECIFICATIONS 2.5 356 420 253 CC-5120 Operating Temperature Color Dimensions Weight Option Supplied from relay box CC-5120 for TALLY Make-contact for each control Pan (RIGHT/LEFT/AUTO), TILT (UP/DOWN) Defroster (ON-OFF), Wiper (ON-OFF) ON-OFF Zoom (WIDE/TELE), Focus (FAR/NEAR), Iris ( CLOSE/OPEN) Indoor use, –10°C to +50°C Black 420 (W) x 47 (H) x 253 (D) mm 2.3 kg (5.07 lb.) 1-size rack-mounting bracket: MB-15B Used in combination with CC-5111B remote control unit, this relay box enables remote control of CCTV camera operation. Relay Box 25 Camera Housings/Pan & Tilt Heads Mounting Brackets Unit: mm Power Input Control Output Control Motorized Pan/Tilt Unit: Camera Housing: Camera Power: Motorized Zoom Lens: Case Cover 165 230 65 23 23 25 6 –ø28 Control Inputs Motorized Pan/Tilt Unit: Camera Housing: Camera Power: Motorized Zoom Lens: 30 100 360 Power requirement Power Consumption 254 260 300 SPECIFICATIONS Control Output Unit: mm Operating Temperature Color Dimensions Weight AC Mains, 50/60Hz 135W (When operating camera, motorized zoom lens, pan/tilt unit, fan, heater and defroster.) Make-contact for each control Pan (RIGHT/LEFT/AUTO), TILT (UP/DOWN) Defroster (ON-OFF), Wiper (ON-OFF) ON-OFF Zoom (WIDE/TELE), Focus (FAR/NEAR), Iris ( CLOSE/OPEN) 24V AC, 50/60Hz for motorized pan/tilt unit, camera housing and camera power supply DC ±6V, 0.15A for motorized zoom lens 1 power supply for TALLY lamp Indoor use, –10°C to +50°C Beige 360 (W) x 300 (H) x 100 (D) mm 7.8 kg SYSTEM BLOCK DIAGRAM Camera Housing Relay Box Power Supply Motorized Pan & Tilt Unit Bracket 53 CC-5120 CC-5111B Long-Distance Remote Control Camera Housing Relay Box Power Supply Motorized Pan & Tilt Unit CC-5120 Control line (A) Control line (B) CC-5111B Bracket Table: 1: Required number of cables for long range remote control systems Example Unit combination Coaxial cable Cable diameter and max. cable length (m) Required number of cables between Relay box ø12 ø16 and remote controller (B) Cable diameter and max cable length (m) Camera Motorized zoom lens Housing Pan/tilt head Relay box Remote controller For Camera For pan/tilt head For housing For motorized zoom lens For video signals C-CC354A CT-6ZMGA CT-21ZMGA CT-10ZMGA + C-BL20 — CC-5525 CC-5120 CC-5111B 3 (2) 7 (6) — 3 1 200 350 12 2000 3800 C-CC354A CT-6ZMGA CT-21ZMGA CT-10ZMGA CC-6000A CC-5521 CC-5120 CC-5111B 0 7 (6) — 3 1 90 120 12 2000 3800 3 C-CC354A CT-6ZMGA CT-21ZMGA CT-10ZMGA + C-BL20 — CC-5521 CC-5120 CC-5111B 3 (2) 7 (6) — 3 1 60 100 12 2000 3800 4 C-CC354A CT-6ZMGA CT-21ZMGA CT-10ZMGA C-CH100FH C-PH200 CC-5120 CC-5111B 3 (2) 7 (6) 2 3 1 40 70 16 1300 2300 C-CC354A CT-6ZMGA CT-21ZMGA CT-10ZMGA C-CH200 C-PH200 CC-5120 CC-5111B 3 (2) 7 (6) 4 3 1 35 60 16 1300 2300 Outdoor 2 Indoor 1 5 ø0.9 ø1.2 Camera Housings/Pan & Tilt Heads Mounting Brackets Required number of cables between pan/tilt head and relay box (A) 1. Depending on the combination units of functions in the system, the number of cables between the pan/tilt head and remote controller can be reduced, or cables can be jointly connected. For further information, refer to Table2. 2. Because maximum cable extension is determined at an ambient temperature of 20°C. it is recommended that thicker cables than those shown above be used. The stated maximum length can be made 1.5 times longer by using two common (COM) cables. 3. It is recommended to provide extra wiring for future system expansion or cable disconnection. 4. When using the CC-5525 pan/tilt head, the CC-50111B remote controller needs to be internally modified, otherwise, the auto-pan function cannot be operated. For further information, please contact the TOA office or TOA dealer in your country or region. 5. When suspending a pan/tilt head, reverse both upper/lower and left/right connections of the CC-5120 relay box and CC-5011B remote controller. For further information, please contact the TOA office or TOA dealer in your country or region. 6. Depending on the circumstances of installation, an earth cable for cameras and pan/tilt heads must used. 7. A camera, pan/tilt head and housing can share the AC-COM cable, but some of them may need connection wires for their internal connections. Table 2 For camera For pan/tilt head For housing For motorized zoom lens CAMERAUP UP AC-COM IRIS AC-COM DOWN WIPER FOCUS (Earth) RIGHT DEF ZOOM LEFT 0N-AC DC-COM AUTO AC-COM (Earth) 1. The AC-COM cable for cameras, pan/tilt heads and housings can be commonly used. However, depending on the combination of units in the system, the units need be bridged. 2. When using a motorized autp-iris zoom lens, it is possible to make connections using three wires omitting IRIS. 54 Camera Selector CC-5131B The TOA's CC-5131B camera selector is intended for use with the CC-5111B remote control unit. Up to 6 cameras and their accompanying CC-5120 relay boxes may be linked to the camera selector. Bridging connection of the CC-5131B is possible to increase the number of linked cameras. Switches are provided for selecting each camera and for camera power. A complete set of terminals is also provided for quick set-up and reliable operation. The camera selector can be mounted on a standard rack cabinet. Camera Selector SPECIFICATIONS 356 420 Video Input 2.5 44.5 Control Output Video Output Operating Temperature Finish 253 Camera Housings/Pan & Tilt Heads Mounting Brackets Unit: mm Dimensions Weight Option 6 make-contact for turning the cameras on or off. 6 make-contact for selecting the cameras to be controlled remotely plus 1 output for extending the camera selector. 6 make-contact for selecting the cameras to be monitored plus 1 output for autoswitching M4 screw terminal, distance between barriers: 8.8 mm 6 inputs for composite video signal 1.0V (p-p) plus 1 input for extending the camera selector. (All inputs excepting the selected input are terminated with 75Ω.) (BNC connector) 1 output with composite video signal 1.0V (p-p) plus 1 output for ectending the camera selector (BNC connector) –10°C to +50°C Panel: Aluminum extrusion, black, 30% gloss Case: Pre-coated steel plate, black, 30% gloss 420 (W) x 47 (H) x 253 (D) mm 2.4 kg Rack-mounting bracket: MB-15B SYSTEM BLOCK DIAGRAM Monitor Camera Selector (CC-5131B) 24V Camera (CC-5111B) Relay Box (CC-5120) Remote Control Unit Control line Video signal line 24V Camera Relay Box (CC-5120) 55 Housing Selection Chart Includes heater, fan, defroster and wiper. Meets IP54 requirements for dust and water resistance. C-CH210FH Includes heater and fan. C-CH200FH Outdoor Use C-CH200 Meets IP33 requirements for dust and water resistance. Includes heater and fan. C-CH100FH CC-6000A Indoor Use Camera Housings/Pan & Tilt Heads Mounting Brackets C-CH100 CC-6080DMB CC-6080DMW CC-6080DMS Pan & Tilt Head Selection Chart Outdoor Use Indoor Use Meets IP54 requirements for dust and water resistance. Withstands load of 11kg (upright) and 10kg (inverted) configuration use. AC MAIN AC 24V Withstands load of 11kg (upright) and 10kg (inverted) configuration use. Remote Control Unit/Power Supply CC-5011B + CC-5941B Remote Control Unit/Relay Box CC-5111B + CC-5120 DC 6V Remote Controller CC-5050B Withstands load of 3kg for upright and inverted configuration use. Withstands load of 3kg for upright and inverted configuration use. C-PH200 CC-5521 CC-5525 CC-5550A 56 57 MULTIPLEXER C-MS161D 16-Channel Duplex Multiplexer C-MS91D DESCRIPTION FEATURES The C-MS161D and C-MS91D multiplexer allows connecting multiple cameras (16 for the C-MS161D, 9 for C-MS91D) for monitoring real-time images as well as recording the images onto a VCR and playing them back. Also included is a frame recording function that records all the images from connected cameras to a VCR sequentially while displaying real-time images on multiple split screens (4-, 9-segment screen etc.), a full screen or zoom screen. The recorded images can also be played back on a split, full or zoom screen. Both offer effective surveillance through the motion detection function which can be selected for desired areas. While recording in this mode, the frame rate is also increased for those areas and when motion is detected, an alarm can be activated. ■ Superb picture quality in a class of its own Multiplexer/ Switcher 9-Channel Duplex Multiplexer • High resolution images • PAL: 720 × 552 pixels • NTSC: 720 × 464 pixels • Proprietary LSI • Digital filter • V-SYNC Position Compensation Circuit (P.A.F.) ■ Versatile, user-friendly operation • Illuminated keys • Multiple display configurations • Zoom, freeze and auto-panning functions • Menu-driven setup • Multi-language ability • Various alarm functions • Motion detection function • 2 VCR connections • Key-lock function • Remote control by C-RM500 58 C-MS161D 16-CHANNEL DUPLEX MULTIPLEXER C-MS161D 16-Channel Duplex Multiplexer 76.2 88.4 96.6 Multiplexer/ Switcher 483 466 420 333.9 319.8 10.6 unit: mm SYSTEM EXAMPLE RS-485 RS-485 C-RM500 C-MS161D Monitor 59 Power source Power consumption Video Input Camera input VCR input Video output Camera output Monitor output Alarm VCR output Alarm Input Alarm output Video loss alarm output Alarm hold output Alarm cancel output Motion detection output Alarm time Remote Buzzer Remote input Remote output: Other Functions VCR Control Switcher control input Alarm output Alarm cancel output Audio VCR input: Monitor output External control RS-232C Remote control terminal Dedicated Remote Controller Recording Output Screen display [Camera screen] Full screen selection Multiple-split screen Zoom Freeze Automatic sequence 220 – 240V AC, 50/60Hz 20W 16 channels, VBS 1.0V(p-p) 75Ω, BNC, 2:1 interlace*2 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, VBS 1.0V(p-p) 75Ω, BNC, loop-through output 2 channels (Either channel can be set as spot output.), VBS 1.0V(p-p) 75Ω, BNC 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) make/brake is selectable by menu setting 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) MANUAL, 10s, 15s, 20s, 30s, 1 – 5min (adjustable in 1-minute steps), Infinite ON or OFF (selectable) 12 channels (6 channels: binary input), no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) 10 channels (6 channels: binary output) NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) Motion detection, Selection of the motion detection pattern, key lock, automatic recognition on time-lapse recording, selection of the recording pattern, selection of the language (English/Spanish/French) on the menu screen 2 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: under 0.3mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, –10dB*1, over 50kΩ, RCA pin jack 1 channel, –10dB*1, low impedance, RCA pin jack 1 channel, D-sub connector (9 P, male) 1 each of input and output, screwless connector Controlled by dedicated remote controller C-RM100 (option), C-RM500 (option) At least 1 frame intervals Selection of the desired camera 4-, 9-, 10- and 16-segment screen (all intermittent displaying, changeable positioning on the segment screen.) Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze screen for individual cameras Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Power source Power consumption Video Input Camera input VCR input Video output Camera output Monitor output Alarm VCR output Alarm Input Alarm output Video loss alarm output Alarm hold output Alarm cancel output Motion detection output Alarm time Remote Buzzer Remote input Remote output: Other Functions VCR Control Switcher control input Alarm output Alarm cancel output Audio VCR input: Monitor output External control RS-232C Remote control terminal Dedicated Remote Controller Recording Output Screen display [Camera screen] Full screen selection Multiple-split screen Zoom Freeze Automatic sequence 110 – 120V AC, 50/60Hz 18W 16 channels, VBS 1.0V(p-p) 75Ω, BNC, 2:1 interlace*2 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, VBS 1.0V(p-p) 75Ω, BNC, loop-through output 2 channels (Either channel can be set as spot output.), VBS 1.0V(p-p) 75Ω, BNC 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) make/brake is selectable by menu setting 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) MANUAL, 10s, 15s, 20s, 30s, 1 – 5min (adjustable in 1-minute steps), Infinite ON or OFF (selectable) 12 channels (6 channels: binary input), no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) 10 channels (6 channels: binary output) NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) Motion detection, Selection of the motion detection pattern, key lock, automatic recognition on time-lapse recording, selection of the recording pattern, selection of the language (English/Spanish/French) on the menu screen 2 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: under 0.3mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, –10dB*1, over 50kΩ, RCA pin jack 1 channel, –10dB*1, low impedance, RCA pin jack 1 channel, D-sub connector (9 P, male) 1 each of input and output, screwless connector Controlled by dedicated remote controller C-RM100 (option), C-RM500 (option) At least 1 frame intervals Multiplexer/ Switcher SPECIFICATIONS (NTSC) SPECIFICATIONS (PAL) Selection of the desired camera 4-, 9-, 10- and 16-segment screen (all intermittent displaying, changeable positioning on the segment screen.) Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze screen for individual cameras Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. [VCR reproduction screen] Full screen selection Selection of the desired camera Multiple-split screen 4-, 9-, and 16-segment screen Zoom Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze Freeze screen for individual cameras [Spot screen] Full screen selection Selection of the desired camera Automatic sequence Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Indication Camera title Up to 8 characters (alphanumeric and symbols) camera No. and time/date can be displayed. Number of Effective Pixels 720 × 552 pixels Operating Temperature 0˚ to +40˚C Finish Panel: aluminum extrusion, black, 30% gloss Case: Surface-treated steel plate, black, 30% gloss, paint Dimensions 420(W) × 96.6 (H) × 333.9 (D) mm Weight 4.3kg Accessory Power cord (2m) × 1, D-sub plug (25 P, threaded in inch) × 2 Option Rack mounting bracket: MB-23B [VCR reproduction screen] Full screen selection Selection of the desired camera Multiple-split screen 4-, 9-, and 16-segment screen Zoom Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze Freeze screen for individual cameras [Spot screen] Full screen selection Selection of the desired camera Automatic sequence Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Indication Camera title Up to 8 characters (alphanumeric and symbols) camera No. and time/date can be displayed. Number of Effective Pixels 720 × 464 pixels Operating Temperature 0˚ to +40˚C Finish Panel: aluminum extrusion, black, 30% gloss Case: Surface-treated steel plate, black, 30% gloss, paint Dimensions 420(W) × 96.6 (H) × 333.9 (D) mm Weight 4.3kg Accessory Power cord (2m) × 1, D-sub plug (25 P, threaded in inch) × 2 Option Rack mounting bracket: MB-23B *1 0dB = 1V *2 That line-locked cameras cannot be connected to the C-MS161D. *1 0dB = 1V *2 That line-locked cameras cannot be connected to the C-MS161D. 60 C-MS91D 9-CHANNEL DUPLEX MULTIPLEXER C-MS91D 9-Channel Duplex Multiplexer 482 465 Multiplexer/ Switcher 31.8 44 51.8 420 334.1 320 10.6 unit: mm SYSTEM EXAMPLE RS-485 RS-485 C-RM500 C-MS91D Monitor 61 Power source Power consumption Video Input Camera input VCR input Video output Camera output Monitor output Alarm VCR output Alarm Input Alarm output Video loss alarm output Alarm hold output Alarm cancel output Motion detection output Alarm time Remote Buzzer Remote input Remote output: Other Functions VCR Control Switcher control input Alarm output Alarm cancel output Audio VCR input: Monitor output External control RS-232C Remote control terminal Dedicated Remote Controller Recording Output Screen display [Camera screen] Full screen selection Multiple-split screen Zoom Freeze Automatic sequence SPECIFICATIONS (NTSC) 220 – 240V AC, 50/60Hz 18W 9 channels, VBS 1.0V(p-p) 75Ω, BNC, 2:1 interlace*2 2 channels, VBS 1.0V(p-p) 75Ω, BNC 9 channels, VBS 1.0V(p-p) 75Ω, BNC, loop-through output 2 channels (Either channel can be set as spot output.), VBS 1.0V(p-p) 75Ω, BNC 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) make/brake is selectable by menu setting 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) MANUAL, 10s, 15s, 20s, 30s, 1 – 5min (adjustable in 1-minute steps), Infinite ON or OFF (selectable) 12 channels (6 channels: binary input), no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) 10 channels (6 channels: binary output) NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) Motion detection, Selection of the motion detection pattern, key lock, automatic recognition on time-lapse recording, selection of the recording pattern, selection of the language (English/Spanish/French) on the menu screen 2 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: under 0.3mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, –10dB*1, over 50kΩ, RCA pin jack 1 channel, –10dB*1, low impedance, RCA pin jack 1 channel, D-sub connector (9 P, male) 1 each of input and output, screwless connector Controlled by dedicated remote controller C-RM100 (option), C-RM500 (option) At least 1 frame intervals Selection of the desired camera 4-, 9 and 10-segment screen (all intermittent displaying, changeable positioning on the segment screen.) Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze screen for individual cameras Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Power source Power consumption Video Input Camera input VCR input Video output Camera output Monitor output Alarm VCR output Alarm Input Alarm output Video loss alarm output Alarm hold output Alarm cancel output Motion detection output Alarm time Remote Buzzer Remote input Remote output: Other Functions VCR Control Switcher control input Alarm output Alarm cancel output Audio VCR input: Monitor output External control RS-232C Remote control terminal Dedicated Remote Controller Recording Output Screen display [Camera screen] Full screen selection Multiple-split screen Zoom Freeze Automatic sequence 110 – 120V AC, 50/60Hz 17W 9 channels, VBS 1.0V(p-p) 75Ω, BNC, 2:1 interlace*2 2 channels, VBS 1.0V(p-p) 75Ω, BNC 9 channels, VBS 1.0V(p-p) 75Ω, BNC, loop-through output 2 channels (Either channel can be set as spot output.), VBS 1.0V(p-p) 75Ω, BNC 2 channels, VBS 1.0V(p-p) 75Ω, BNC 16 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) make/brake is selectable by menu setting 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) 1 channel, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) MANUAL, 10s, 15s, 20s, 30s, 1 – 5min (adjustable in 1-minute steps), Infinite ON or OFF (selectable) 12 channels (6 channels: binary input), no-voltage make contact input, open voltage: 5V DC, short-circuit current: 5mA, D-sub connector (25 P) 10 channels (6 channels: binary output) NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, D-sub connector (25 P) Motion detection, Selection of the motion detection pattern, key lock, automatic recognition on time-lapse recording, selection of the recording pattern, selection of the language (English/Spanish/French) on the menu screen 2 channels, no-voltage make contact input, open voltage: 5V DC, short-circuit current: under 0.3mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, NPN open collector output, withstand voltage: 20V DC, control current: under 20mA, Screwless connector 2 channels, –10dB*1, over 50kΩ, RCA pin jack 1 channel, –10dB*1, low impedance, RCA pin jack 1 channel, D-sub connector (9 P, male) 1 each of input and output, screwless connector Controlled by dedicated remote controller C-RM100 (option), C-RM500 (option) At least 1 frame intervals Multiplexer/ Switcher SPECIFICATIONS (PAL) Selection of the desired camera 4-, 9- and 10-segment screen (all intermittent displaying, changeable positioning on the segment screen.) Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze screen for individual cameras Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. [VCR reproduction screen] Full screen selection Selection of the desired camera Multiple-split screen 4- and 9-segment screen Zoom Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze Freeze screen for individual cameras [Spot screen] Full screen selection Selection of the desired camera Automatic sequence Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Indication Camera title Up to 8 characters (alphanumeric and symbols) camera No. and time/date can be displayed. Number of Effective Pixels 720 × 552 pixels Operating Temperature 0˚ to +40˚C Finish Panel: aluminum extrusion, black, 30% gloss Case: Surface-treated steel plate, black, 30% gloss, paint Dimensions 420(W) × 51.8 (H) × 334.1 (D) mm Weight 3.5kg Accessory Power cord (2m) × 1, D-sub plug (25 P, threaded in inch) × 2 Option Rack mounting bracket: MB-15B [VCR reproduction screen] Full screen selection Selection of the desired camera Multiple-split screen 4- and 9-segment screen Zoom Electronic 2x zoom for the desired camera (zooming position changeable, auto panning and auto tilting possible) Freeze Freeze screen for individual cameras [Spot screen] Full screen selection Selection of the desired camera Automatic sequence Full screen (individual cameras), 4-segment screen (camera groups), switching time intervals of 0 – 99 sec. that can be set in 1 sec. units. Indication Camera title Up to 8 characters (alphanumeric and symbols) camera No. and time/date can be displayed. Number of Effective Pixels 720 × 464 pixels Operating Temperature 0˚ to +40˚C Finish Panel: aluminum extrusion, black, 30% gloss Case: Surface-treated steel plate, black, 30% gloss, paint Dimensions 420(W) × 51.8 (H) × 334.1 (D) mm Weight 3.5kg Accessory Power cord (2m) × 1, D-sub plug (25 P, threaded in inch) × 2 Option Rack mounting bracket: MB-15B *1 0dB = 1V *2 That line-locked cameras cannot be connected to the C-MS91D. *1 0dB = 1V *2 That line-locked cameras cannot be connected to the C-MS91D. 62 C-MS161D/C-MS91D MULTIPLEXER Proprietary TOA LSI ensures high picture quality. Digital Filter Special Video Signal Processor A newly developed TOA LSI incorporates all the specialized technology required for signal processing for split screen displays, zoom, VCR recording and playback. Incorporated into the LSI´s functions is a high-performance digital filter that supports high quality display requirements. The digital filter averages both vertical and horizontal pixel gap luminance and crops pixels in split-screen display modes. Visually, diagonal lines take on increased definition while flickering is minimized for bright objects. The edges of magnified images are also smoothed during zooming in or out. Optimizes split-screen displays TOA's specialized LSI eliminates the common phenomenon seen when objects that move in a direction from left to right often appear separated when viewed in a top to down direction. It is caused by frequency differences of camera inputs and output signals during a split-screen display. V-SYNC Position Compensation Circuit Newly developed V-SYNC Position Compensation Circuit precisely corrects and minimizes any unintentional shaking of reproduced video images that can be caused by the quasi-VSYNC signal that a time-lapse VCR can introduce. Multiple Split Screen Display Live monitoring and VCR playback can be seen in all split screen options (16 segment only with C-MS161D). Multiplexer/ Switcher 16-segment 1 5 9 13 2 6 10 14 3 7 11 15 10-segment 4 8 12 16 1 1 5 9-segment 2 2 6 3 7 4 8 4-segment 1 2 3 4 5 6 7 8 1 2 3 4 1- segment 1 9 (only when real time monitoring) For live camera monitoring segments, cameras can be assigned to the desired position. 1 By using shift up/down and shift left/right function keys, the user can select the desired multi-segment screen. 2 3 4 5 6 7 8 9 10 Then the 1-16 camera keys can be used to assign cameras to the segments in the multi-segment screen selected earlier. 10 2 3 4 5 6 1 7 8 9 In a 4-segment screen, live cameras can be selected in sequence. Group1 Group 2 Group 3 Group 4 1 2 5 6 9 10 13 14 3 4 7 8 11 12 15 16 With camera selection, a required camera can be assigned priority to always be shown (camera 1 selected). Group1 63 Group 2 Group 3 Group 4 1 2 1 5 1 8 1 11 3 4 6 7 9 10 12 13 FEATURES Display Configuration Table Sequence Split(4)-screen sequence Full-Screen display Split(4)-screen display Split(9)-screen display Split(10)-screen display Split(16)-screen display Zoom display (2x) Auto-panning and tilt display Freeze Live C-MS161D C-MS91D √ √ √ √ √ √ √* √* √* √* √* √* √* – √ √ √ √ √ √ VCR Playback C-MS161D C-MS91D – – – – √ √ √ √ √ √ – – √ – √ √ √ √ √ √ "Seamless Operation" by Connecting 2 Time-Lapse VCRs. • You can connect 2 time-lapse VCRs to TOA multiplexers. You can change or rewind a video tape without interrupting recording. • The duplex multiplexers C-MS161D and C-MS91D also allow you to review previous recording (VCR2) without stopping new real-time recording (VCR 1). Real-time multiple surveillance + recording. C-MS91D C-MS161D * Robotic motion CAMERA Motion Detection Mode TOA's new multiplexers incorporate an extremely useful new function of smart image detection. Each camera utilized in a system can be set to detect motion. VCR Real-time recording + multiple playback. CAMERA C-MS91D C-MS161D VCR-1 1 frame The multiplexer monitors each of 192 (16 x 12) frames for brightness. When the frames in a configured area have brightness level variations, motion detection is activated. VCR-2 Multiplexer/ Switcher Motion Detection Frame Size Settings The entire screen is divided into 192 frames (16 horizontal, 12 vertical). Select frame numbers to freely configure an area that will be under motion detection. Electronic Zoom, Auto Tilt and Auto Panning Features Included. TOA multiplexers enable electronic 2X zooming to be selected along with desired position. In addition, electronic Auto Pan and Auto Tilt functions enhance monitoring and surveillance capability. Motion detection can only be set to activate over a configured area of frames, therefore reducing operational errors. The entire screen is divided into 16 frames (4 horizontal, 4 vertical) and motion detection can be set to activate in any of the 16 frames or combination of frames. • 2x Zoom (adjustable zoom position) 1 configured area Motion detection works by responding to variations in brightness level. To minimize operational errors, five different sensitivity settings are provided to allow fine adjustment control. • The auto-panning and -tilt functions electronically simulate eye-movement of a sentry CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA Motion Detection Operation 1 2 3 4 5 6 7 8 9 10 11121314 CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA CAMERA Camera 3 when in motion detection mode. 13234353637383 Images from camera selected for motion detection will increase frame rate for enhanced monitoring. 64 C-MS161D/C-MS91D MULTIPLEXER Versatile Alarm Functions TOA multiplexers offer many alarm functions that are easily set in the setup menu. Sensor Alarm: Each camera connected is equipped with a sensor input terminal. Alarm activation triggers a buzzer while onscreen display warning and video recording speed is automatically set to standard speed. Multiple Alarm Inputs allow prioritizing cameras when an alarm is generated. When multiple alarms are generated, video image switching is suspended and the alarms are put on hold so that the operator can select the alarm’s corresponding camera’s images to view in desired order. In addition, each alarm terminal can be set to notify on a break-or-make or make basis. Summer Time (daylight savings) The timer function can be adjusted for summer time and can also be set to adjust automatically for it. Remote control Video Loss Alarm: Alerts when power or signal from a particular camera is lost. Letters "VL" and the camera ID number will be displayed. Each multiplexer is equipped with an RS-232C port on the rear panel so that it can be linked for control externally from a remote location. The C-RM500 Remote Controller can be used to switch and select cameras individually or by group, sequence-display, multi-split screen modes. It connects to the multiplexer via the remote control terminal on the rear panel. Alarm Information: Dates, times and camera ID number of sensor and video loss alarms can be reviewed on an independent alarm information screen. A maximum of 64 events will be recorded and a new event will record over the oldest event. A key-lock function can be set to prevent unauthorized access to unit controls and tampering. VCR Reproduction Alarm: A buzzer sounds when playing back the part of a recording that contains a sensor alarm event. Multiplexer/ Switcher Multi-Language Ability Offering flexible use for multi-language environments, TOA multiplexers will show onscreen information and allow menudriven set-up and operation in English, French, and Spanish. Key-lock function Frame Recording Function Mechanism of a Multiplexer CAMERA1 CAMERA 2 The frame recording system switches cameras for each frame while recording. For every frame (25 frames/sec for PAL and 30 frames/sec for NTSC), a multiplexer sends a different picture taken by a different camera to a VCR so that a single VCR is able to make recordings for multiple cameras. Continuous images can be reproduced during replay by reading corresponding frames for each camera. Recorded images may be viewed as full-screen display for each 65 independent camera or in a split-screen display that shows multiple camera views at the same time. A conventional sequential switcher changes camera feeds every few seconds, making continuous motion replay impossible. Allocating a VCR for each camera is also prohibitive in terms of costs. Multiplexers that use the frame recording system records images from all cameras and are costeffective. FEATURES The tables below indicate numbers and the interval of recorded fields using various setups for both PAL and NTSC PAL Recording intervals [sec] Conventional time-lapse VCR 4 cameras 8 cameras 16 cameras 4 cameras 8 cameras 16 cameras Standard 02 6.25 3.13 1.56 0.16 0.32 0.64 4 cameras 8 cameras 16 cameras 4 cameras 8 cameras 16 cameras Standard 06 6.25 3.13 1.56 0.16 0.32 0.64 4 cameras 8 cameras 16 cameras 4 cameras 8 cameras 16 cameras Standard 02 7.49 3.75 1.87 0.13 0.27 0.53 4 cameras 8 cameras 16 cameras 4 cameras 8 cameras 16 cameras Standard 06 7.49 3.75 1.87 0.13 0.27 0.53 PAL Recording mode Recording Time (hour) Number of recorded frames per second [Frame/sec] Recording intervals [sec] Recording intervals [sec] Recording intervals [sec] Time-lapse mode 48 72 120 0.50 0.34 0.20 0.25 0.17 0.10 0.13 0.08 0.05 2.00 2.96 4.88 4.00 5.92 9.76 8.00 11.84 19.52 168 0.15 0.07 0.04 6.80 13.60 27.20 240 0.10 0.05 0.03 9.68 19.36 38.72 480 720 960 0.05 0.03 0.03 0.03 0.02 0.01 0.01 0.01 0.01 19.28 28.88 38.48 38.56 57.76 76.96 77.12 115.52 153.92 18 4.17 2.08 1.04 0.24 0.48 0.96 30 2.50 1.25 0.63 0.40 0.80 1.60 Time-lapse mode 48 72 96 1.39 0.96 0.74 0.69 0.48 0.37 0.35 0.24 0.18 0.72 1.04 1.36 1.44 2.08 2.72 2.88 4.16 5.44 240 0.12 0.06 0.03 8.07 16.15 32.30 480 0.06 0.03 0.02 16.08 32.17 64.33 168 0.43 0.22 0.11 2.32 4.64 9.28 Conventional time-lapse VCR NTSC Recording mode Recording Time (hour) Number of recorded frames per second [Frame/sec] 24 0.96 0.48 0.24 1.04 2.08 4.16 Real-time VCR, continuous mode NTSC Recording mode Recording Time (hour) Number of recorded frames per second [Frame/sec] 12 1.79 0.89 0.45 0.56 1.12 2.24 12 2.14 1.07 0.54 0.47 0.93 1.87 24 1.15 0.58 0.29 0.87 1.74 3.47 Time-lapse mode 48 72 120 0.60 0.41 0.25 0.30 0.20 0.12 0.15 0.10 0.06 1.67 2.47 4.07 3.34 4.94 8.14 6.67 9.88 16.28 168 0.18 0.09 0.04 5.67 11.34 22.69 720 960 0.04 0.03 0.02 0.02 0.01 0.01 24.09 32.10 48.18 64.20 96.36 128.40 Multiplexer/ Switcher Recording mode Recording Time (hour) Number of recorded frames per second [Frame/sec] Real-time VCR, continuous mode 18 5.00 2.50 1.25 0.20 0.40 0.80 30 3.00 1.50 0.75 0.33 0.67 1.33 Time-lapse mode 48 72 96 1.67 1.15 0.88 0.83 0.58 0.44 0.42 0.29 0.22 0.60 0.87 1.13 1.20 1.74 2.27 2.40 3.47 4.54 168 0.52 0.26 0.13 1.94 3.87 7.74 * Indicated figures show standard values. The actual values may vary slightly depending on connected VCR models. 66 C-MS161D/C-MS91D SETUP SCREEN MENU SELECTION Setup Screen Conveniently allows setting up a camera and making adjustments and parameter changes through a menu-driven setup procedure. 1. USER MENU 2. TOTAL MENU 3. LANGUAGE 4. INITIALIZATION Menu TOTAL MENU 1. CLOCK 2. TITLE 3. REC/ALARM 4. OPTION 1 5. OPTION 2 Multiplexer/ Switcher • Year, month, date of the month, date of the week and time of the day setup • Summer time • Title and camera selection 67 1. USER MENU 6. REMOTE 7. SEQ SKIP 8. AL DATA 9. REC PTN 10. MOTION 1. CLOCK 2. TOTAL MENU 2. TITLE 3. LANGUAGE • Recording mode and fail-safe ON/OFF • Alarm recording mode and fail-safe ON/OFF • Recorder mode • Video loss alarm • Multipule alarm mode • Alarm hold • Alarm signal and duration • Sensor alarm • Alarm reception 3. REC/ALARM • Sequential display intervals for monitor • Spot display sequence interval • Startup camera mode preference • Startup VCR mode preference • Recording pattern selection • Motion detection pattern selection 4. OPTION 1 • Buzzer ON/OFF • Character display 0N/OFF(monitor) • Character display pattern selection (monitor) • Full screen time/date display • Character display ON/OFF (VCR) • Character display pattern selection (VCR) • Monitor output 2 setup • 4-segment display camera group setup • Background color selection • Board line of multi-screen • Horizontal position of screen • Vertical position of screen • Refresh function 5.OPTION 2 • Control access setup • Recording pattern control • Motion detection pattern control • RS-232C bit rate • RS-232C protocol 6. REMOTE • 0n/0ff for each camera during sequential display (monitor, spot) 7. SEQ SKIP • Alarm log 8. AL DATA • Recording pattern 1 and 2 • Recording camera assignments 9. REC PTN • Motion detection pattern 1 and 2 • Motion detection camera assignments • Motion detection sensitivity • Motion detection area • Motion detection hold time • Motion detection output 10. MOTION 4. INITIALIZATION • Year, month, date of the month, date of the week and time of the day setup. • Daylight savings time • Character on/off • Title (monitor) • Date/Time insertion • Alarm log • Recording pattern setup • Motion detection pattern setup • Character language selection (English, French, Spanish) • Resetting to factory-set values (without time/date setup and character language selection) Quad Screen Splitter C-QA40 TOA's C-QA40 Quad Screen Splitter is a video processor that displays 4segment split screen images from up to 4 connected CCTV cameras on a single monitor. Because its width is approximately the same as a 14-inch monitor, the monitor can be placed on top of the C-QA40 to save space. The C-QA40 can also be mounted in an equipment rack using its optional MB-QA40 brackets. Quad Screen Splitter Power Source Power Consumption Camera Input 44 53.3 350 Video Output 315.5 298 12.5 Display Rate External Control Input/ Output Unit: mm Title Indication Synchronizing System Automatic Sequence Operating Temperature Operating Humidity Finish Dimensions Weight Accessory Option 110 – 120, 220 – 240 V AC, 50/60 Hz 7W 4 channels (asynchronous, loop-through output), VBS 1.0 V(p-p) 75 Ω, BNC 2 channels, VBS 1.0 V(p-p) 75 Ω, BNC Monitor 1: 4-segment split-screen display or display selected with Monitor 2 Monitor 2: Full screen or 4-segment split-screen display or sequential switching NTSC: Real time: 60 fields (30 frame/second) PAL: Real time: 50 fields (25 frame/second) Alarm input (1, 2, 3, 4, ALARM RESET) or remote input (1, 2, 3, 4, sequential switching, QUAD mode) no-voltage make contact input, open voltage: 2.9 V DC, short circuit current: 0.2 mA or less Alarm output: Open collector output, withstand voltage: 12 V DC, control current: 30 mA or less Alarm/remote input signal pulse width: 0.3 seconds or more Lock input: No-voltage make contact input, open voltage: 2.9 V DC, short circuit current: 0.2 mA or less Maximum 8 characters per channel (alphanumeric and symbols) Internal synchronization Automatic sequence switching interval: 1 – 60 seconds Skip function; Selection of cameras to skip for each input 0°C to +40°C 30% to 90% (must be free from dew condensation) Panel: ABS resin, black, 30% glossy, paint Case: Pre-coated steel plate, black, 30% glossy 350 (W) x 53.3 (H) x 315.5 (D) mm 2.5 kg Power cord (2 m) … 1 Rack mounting bracket: MB-QA40 Multiplexer/ Switcher SPECIFICATIONS SYSTEM EXAMPLE Monitor Monitor Single Cable Camera 1 1 4 C-QA40 Monitor out Alarm out 2 Video input VCR Camera out 4 Separate room 3 4 4 Alarm in C-QA40 Monitor 4 Sensor 68 Manual Switchers CC-3011B Manual Switcher These manual mechanical lock-type switchers can manage up to six (CC-3011B) or twelve (CC-3021B) camera inputs from a single output. Both units can also be mounted in a rack using an optional bracket. SPECIFICATIONS Video input Up to 6 (CC-3011B) Up to 12 (CC-3021B) VBS 1.0 Vp–p/ 75Ω (BNC) VBS 1.0 Vp–p/ 75Ω (BNC) 1 input Mechanical Lock type Black (mat) 210 (W) x 47 (H) x 248 (D) mm 1.4 kg Rack mounting bracket: MB-15B-J for two units MB-15B-BK for one unit Video output Switches Finish Dimensions Weight Option CC-3021B Manual Switcher CC-3011B Multiplexer/ Switcher 210 158 210 231 231 248 248 2.5 158 2.5 44.5 44.5 CC-3021B Unit: mm ASSOCIATED EQUIPMENTS C-VD6 Video Distributor CC-3331B CC-3350B Video Signal Adaptor Assocuate Equipments Cable Compensator 70 Video Distributor C-VD6 The TOA's C-VD6 video distributor adds versatility to CCTV operation by distributing one video signal to six video outputs, or two different video signals each to three outputs. The unit is compact and lightweight and can be mounted on a standard rack cabinet with an optional bracket. 1,700 Video Distributor SPECIFICATIONS Power Requirements Power Consumption Video Input Video Output Distribution 46 44 210 Ambient Temperature Finish Dimensions Weight Option 296 285 Unit: mm 120V AC (“L” version) 230V AC (“HH” and “UK” version), 50/60Hz 4.5W 1V (p-p) 75Ω (BNC) 2 inputs 1V (p-p) 75Ω (BNC) 6 outputs One input to 6 outputs or 2 different inputs to each of 3 outputs (switchable) –10°C to +50°C Panel: Semi-glazed melamine baked paint (black) 210 (W) x 46 (H) x 296 (D) mm 1.8 kg Rack mounting bracket: MB-15B-J for two units MB-15B-BK for one unit BASIC CONNECTIONS 1 input, 6 distributions 2 input, 3 distributions Monitor Monitor Assocuate Equipments A 71 BNC Video distributor Camera BNC Camera A C-VD6 A A B B BNC Video distributor C-VD6 BNC B BNC B Cable Compensator CC-3331B Increase CCTV operational flexibility by off-setting video signal transmission line losses bgetween camera and monitor. A 4-step cable selector and a semifixed output level controller are available to help provide the clearest possible on-screen images. System settings are based on cable type and cable running distance. Cable Compensator SPECIFICATIONS 231 248 Unit: mm Cable 5C-2V 7C-2V 10C-2V 1 500m (545yd) 600m (654yd) 750m (817yd) Cable length 2 3 1000m (1090yd) 1500m (1635yd) 1200m (1308yd) 1800m (1962yd) 1500m (1635yd) 2200m (2398yd) 4 2000m (2189yd) 2400m (2616yd) 3000m (3270yd) Assocuate Equipments 158 210 220/240V AC, 50/60Hz 5.0W 1V (p-p) 75Ω (BNC) 2 inputs –10°C to +50°C Black (mat) 210 (W) x 47 (H) x 248 (D) mm 1.8 kg Rack mounting bracket: MB-15B-J for two units MB-15B-BK for one unit 2.5 44.5 2000 Power Requirements Power Consumption Video Input Ambient Temperature Finish Dimensions Weight Option 72 Video Signal Adaptor CC-3350B The TOA's CC-3350B is a combined video signal adaptor and video transformer. It enables the transmission of a video signal from a CCTV camera to a monitor TV by means of a pair of twisted wires, in locations where coaxial cables are hard to install. The maximum cable length is approximately 1.2 km (1,312 yards). Stable video picture resolution is ensured by built-in DC restorer and a high-frequency compensator. Three cable length switches may be set in 8 combinations, for cable lengths from 0 – 1,200 meters, in steps of 150 meters. The CC-3350B is rack-mountable with an optional rack mounting kit. Video Signal Adaptor SPECIFICATIONS 2.5 44.5 Power Requirements Power Consumption Camera Input 210 6 231 Unit: mm 248.5 Video Transformer 230V AC, 50/60Hz Aprrox. 3.5W 1 × VBS 1.2V (p-p) 110Ω, balanced (screw terminal) Cmera Output 2 × VBS 1.0V (p-p) 75Ω, unbalanced (BNC) High Range Max. 40dB at 5MHz with cable length select Compensation switch set to 1,200m posision Cable Length 8 positions in step of 150m Select Switch Max. 1,200m Appricable Cable Characteristc impedance: 110Ω Core diremeter: 0.65mm Signal-twisted pair cable Video Level Variable Range Approx. ±3dB Ambient Temperature –10°C to +50°C Color Black (mat) Dimensions 210 (W) × 47 (H) × 248.5 (D) mm Weight 1.7kg Accessory Power cord × 1 Rack Mounting Bracket MB-15B-J: For rack mounting two CC-3350B units (option) MB-15B-BK: For rack mounting one CC-3350B unit The TOA CC-5050B Pan Head Controller permits to remotely control up to three CC-5550A pan heads. SPECIFICATIONS 51 34.6 Assocuate Equipments 18 Video Input Video Output (screw terminal) Color Dimensions Weight 94 113 73 Unit: mm 1 × VBS 1.0V (p-p) 75Ω, balanced (BNC) 1 × VBS 1.2V (p-p) 110Ω, unbalanced Off white 113 (W) × 34.6 (H) × 51 (D) mm 300g COAXIAL MULTI-TRANSMISSION UNIT C-AP105 2 units in every set DESCRIPTION FEATURES The TOA C-AP105 Coaxial Multi-Transmission unit allows a single cable to effectively handle duplex audio and simplex video transmission. The 1 cable-compatible C-AP105 can therefore be useful for monitoring several sources in a single CCTV system. The C-AP105 easily fits into an existing CCTV system without needing major changes to the system. Sources such as a camera, microphone, speaker and 4 sensors (for alarms) can be connected to the C-AP105 that will transmit the information to another C-AP105 that can be as far away as 600m (when using 5C-FB cable). ● Transmit video, audio and control signals on one coaxial cable • Video signal (simplex) • Audio signal (duplex) • Control signals (4 contacts/duplex) ● System integration with security and audio equipment. • Camera/monitor/microphone/speaker/sensor etc. • Save cable lines ● Speaker output • 1W (8 ohms) amplifier SYSTEM EXAMPLE Video Audio Camera Monitor Audio C-AP105 Sensor Max. 4 Coaxial Multi-Transmission Unit ● Maximum cable length 600m (when using 5C-FB cable) Note: The C-AP105 includes one each of Unit A and Unit B. C-AP105 Control Control Microphone Speaker Speaker Microphone Control Input Max. 4 Control Output Max. 4 74 SPECIFICATIONS *0 dB = 1 V C-AP105 COAXIAL MULTI-TRANSMISSION UNIT Power Source 12 V DC, 350 mA (cage clamp) Solid Wire: ø0.4 – 1.2 mm (AWG 26 – 16) Stranded Wire: 0.3 – 1.25 mm2 (AWG 22 – 16) AC/DC adapter not supplied by TOA. But an AC/DC adapter can use. Nominal Output: 12 V DC/over 350 mA (under 18 V DC at no load) Plug: Internal diameter; 2.1 mm, Outer diameter; 5.5 mm, center + (EIAJ RC-6705) Power Consumption 3 W (standby), 8 W (maximum output) Represents value per unit Coaxial Cable Length (between units) RG-59/U: Max. 400 m 5C-2V: Max. 400 m Carrier Unit A: Transmission; 50.65 MHz/Reception; 53.65 MHz Unit B: Transmission; 53.65 MHz/Reception; 50.65 MHz Transmission Direction Communications in both directions between a pair of (2) units (Other equipment cannot be connected between units.) Connector AP Line Terminal Video Input/Output Terminal 5C-FB: Max. 600 m 3C-2V: Max. 300 m BNC BNC (DC–8 MHz, loss: under 1 dB) Audio Modulation System Frequency Deviation FM ±75 kHz (1 kHz) Frequency Response 100 – 10,000 Hz S / N Ratio Input 54 dB (MIC)/65 dB (LINE) MIC: -60 dB*, 2 kΩ, unbalanced, phantom power (externally connected to microphone input terminal) LINE: -20 dB*, 10 kΩ, unbalanced (MIC/LINE switch–selectable)Removable terminal block (3 pins) Line Output Speaker Terminal 0 dB*, 10 kΩ, unbalanced, pin jack Max. 1 W, 8 Ω, removable terminal block (3 pins) Contacts Transmission System Sub-carrier AM (DTMF) Contact Input 4 contacts, no-voltage make contact input, open voltage: 12 V DC, loop resistance: under 200 Ω (short-circuit current: 5 mA), removable terminal block (8-pins) Contact Output 4 contacts, open collector output, withstand voltage: 30 V DC, Current: max. 10 mA, removable terminalblock (8 pins) Operating Temperature -10°C to +50°C Operating Humidity Finish Dimensions Under 90% RH (no due condensation produced) Panel: Pre-coated steel plate, black, 30% gloss Cover: Pre-coated steel plate, black, 30% gloss 210 (W) × 47.4 (H) × 126.5 (D) mm (represents value per unit) Weight Accessory 815 g (represents value per unit) Microphone (fitted with a microphone mounting plate and 3 pins connector) × 1, Wall mounting bracket × 4, Wall mounting screw × 8, Wall mounting bracket mounting screw…8, Microphone mounting screw × 1, Microphone mounting plate mounting screw × 2, Removable terminal plug (3 pins) × 3, Removable terminal plug (8 pins) × 4 Coaxial Multi-Transmission Unit Note: The C-AP105 includes one each of Unit A and Unit B. APPEARANCE AND DIMENSIONAL DIAGRAMS Wall mounting bracket (accessory) 126.5 11.8 75 50.6 47.4 42.4 210 VOICE SECURITY INTERCOM SYSTEM VS-900 SERIES DESCRIPTION SYSTEM FEATURES TOA's VS-900 is a security communications system specially designed for applications in such facilities as office buildings, factories, schools, hospitals, and prisons. Installed separately from conventional general-purpose internal communications systems, the VS-900 can be used to access control or make urgent calls in emergency situations. The system is comprised of a central exchange and remote stations, and permits calls to master stations located in the central control room or in facility guard rooms from substations installed in such varied locations as entrance gates, parking lots or building entrances. The exchange itself features modular construction that permits easy customization to fit the desired scale and application, and later meet changing customer needs by simply plugging in the corresponding cards. Up to 4 master stations and 64 substations can be connected per exchange, and the system can be expanded to up to 64 master stations and 1,024 substations through the tie-line connection of up to 16 exchanges. A standard personal computer can also be connected to the exchange to provide convenient adjustment of system setting functions and automatic logging of communication operations. A full range of exchange functions other than basic conversation are also featured, including call forwarding, scan monitoring, emergency conference, conversation recording by way of external equipment, and paging by way of an external amplifier. There are five different types of substations, including those of indoor-use, outdoor-use, and vandal-resistant types. The VS-900 can also be used in combination with CCTV, access control, emergency broadcast systems or other security equipment to create a more effective security system and ensure a higher level of safety and security in each facility. ■ System Capacity • Single Exchange 4 Master stations (enlargement unit: 2) 64 Substations (enlargement unit: 16) • Up to 16 Exchanges 64 Master stations 1,024 Substations ■ Remote system management via RS-232C port • PC programming and monitoring software • Program and maintain multiple exchanges offsite from one PC (via modem) ■ Audio and Data Logging • PC archive of all system activity (RS-232C port) • Record individual Master station and telephone audio ■ Outside Line Communication • Supports two C/O trunks • Substation to outside telephone line communication ■ Paging Interface • 16 control outputs • 1 voice output Voice Security Intercom System ■ Master Station Flexibility • TOA master with alphanumeric display and clock • Supports single-line telephone equipment with Caller-ID* ■ External Audio Input • 4 activation inputs and 1 audio input for external source distribution *in compliance with FCC regulation Part 68. 76 VS-900MF Main Frame Card modules installed here. Includes 2 RS-232C ports. SPECIFICATIONS 101.6 164.9 101.6 443.7 Power Source Current Consumption Speech Path Configuration Serial Port Note: Photo shows Main Fame with card modules installed. 288.3 37.8 420 466.6 483.6 20V AC, 24V DC 5.5A Time sharing switch (T1 stage) Serial Port complies with the RS-232C Standard, D-sub connector (9-pin, female), 2 ports Rack- and wall-mountable Installation Method Other Real time clock for time control, Unit's presence/ non-presence detection, System programming data maintenance, Power switch Connection Terminals Bus connector: DIN connector (64-pin, female) × 9 PU-200 connection terminal: 4-pin × 2 (2 PU-200s are connectable) 24V DC input terminal: 4-pin (with grounding terminal) Operating Temperatures 0°C to +40°C Finish Pre-coated steel plate, black, 30% gloss Dimensions 483.6 (W) × 443.7 (H) × 288.3 (D)mm Weight 12.7kg Accessories Rack mounting bracket × 2, Rack mounting screw × 8, Fibber washer × 8, Mounting screw × 6, Cable clip × 20, Floppy disk (PC setting software) × 1. CR2032 battery × 1, Connector (4-pin) × 3 VS-900MS Master Station Interface Card For connecting up to two master stations per card. An external recording device can be connected to each line. SPECIFICATIONS Power Source Line 1 Recording HOT GND HOT GND Voice Output Control Output HOT GND HOT GND Voice Output Control Output 305 Line 1 for master station Line 2 for master station Line 2 Recording 144 5V DC, 24V DC (supplied from the main frame) Current Consumption 50mA (5V DC), 200mA (24V DC) Supply Power 24V DC, 80mA Number of Lines 2 lines Conversation Recording Voice output: 0dB*, unbalanced Output Control output: Open collector output, withstand voltage: 24V DC, control current: 20mA Option Master station connection monitoring function Connection Terminals Main frame connection side: DIN connector (64-pin, male) Line output: 4-pin × 2 Recording voice/control output: 4-pin × 2 Operating Temperatures 0°C to +40°C Weight 350g Accessories Connector (4-pin) × 4, Ferrite clamp × 2 * 0 dB = 1V VS-900AL Telephone Interface Card For connecting up to two telephones per card. An external recording device can be connected to each line. Use the telephone which complies with the FCC regulation Part 68. Voice Security Intercom System SPECIFICATIONS Line 1 for telephone Line 1 Recording HOT GND HOT GND Voice Output Control Output Line 2 for telephone Line 2 Recording HOT GND HOT GND Voice Output Control Output 305 Power Source 144 77 Unit: mm 5V DC, 15V DC, 24V DC (supplied from the main frame) Current Consumption 150mA (5V DC), 30mA (15V DC), 200mA (24V DC) Supply Power 24V DC, 80mA Number of Lines 2 lines Conversation Recording Voice output: 0dB*, unbalanced Output Control output: Open collector output, withstand voltage: 24V DC, control current: 20mA Selective Signal Type DTMF signal Line loop detection function Monitoring Function Applicable Terminal Telephone sets to comply with FCC Part 68 Control Function Call signal transmission, Audible signal transmission, Caller identification signal transmission (Caller ID Function) Main frame connection side: Connection Terminals DIN connector (64-pin, male) Line output: 2-pin × 2 Recording voice/control output: 4-pin × 2 Operating Temperatures 0°C to +40°C 400g Weight Connector (2-pin) × 2, Accessories Connector (4-pin) × 2, Ferrite clamp × 2 * 0 dB = 1V VS-900CO Outside Line Interface Card Connects up to two outside lines per card. An external recording device can be connected to each line. SPECIFICATIONS Power Source 305 Outside Line GND Line 1 GND Line 1 Recording HOT GND HOT GND Line 2 Outside Line GND Line 2 Recording HOT GND HOT GND Voice Output Control Output GND Voice Output Control Output 144 5V DC, 15V DC, 24V DC (supplied from the main frame) Current Consumption 300mA (5V DC), 50mA (15V DC), 50mA (24V DC) Number of Lines 2 lines Conversation Recording Voice output: 0dB*, unbalanced Output Control output: Open collector output, withstand voltage: 24V DC, control current: 20mA Selective Signal Type DTMF signal Signal Format Loop start and Ground start compatible Main Functions DTMF dial signal transmission function, DTMF signal detection function, call signal (receiving) detection Connection Terminals Main frame connection side: DIN connector (64-pin, male) C/O line connection side: 4-pin × 2 Recording voice/Control output: 4-pin × 2 Operating Temperatures 0°C to +40°C Weight 380g Accessories Connector (4-pin) × 4 * 0 dB = 1V VS-900AF Audio Function Card Enables conference, external amplifier paging and external source distribution functions. SPECIFICATIONS Power Source Voice Input Control Input 1 Control Input 2 Control Input 3 Control Input 4 HOT GND Voice Output HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND HOT GND 305 Control Output 1 Control Output 2 Control Output 5 Control Output 6 Control Output 9 Control Output 10 Control Output 13 Control Output 14 HOT GND HOT GND Control Output 3 Control Output 4 Control Output 7 Control Output 8 Control Output 11 Control Output 12 Control Output 15 Control Output 16 144 5V DC, 15V DC, 24V DC (supplied from the main frame) Current Consumption 100mA (5V DC), 50mA (15V DC), 30mA (24V DC) Paging Output Voice output: 1 output, 0dB*, unbalanced Control output: 16 outputs, open collector output, withstand voltage: 24V DC, control current: 20mA External Source Voice input: 1 input, 0dB*, unbalanced Distribution Control input: 4 inputs, no-voltage make contact, open voltage: 24V DC, short circuit current: 20mA Conference Link 1 link (up to 4-party conference) Connection Terminals Main frame connection side: DIN connector (64-pin, male) External interface side: Voice output 2-pin Control output 2-pin × 16 Voice input 2-pin Control input 2-pin × 4 Operating Temperatures 0°C to +40°C Weight 230g Accessories Connector (2-pin) × 2, Connector (4-pin) × 10 * 0 dB = 1V Interconnects multiple exchanges. Connects up to 4 links using one pair of data lines and two pairs of voice lines. SPECIFICATIONS Voice line 1 HOT COM HOT COM Voice line 2 HOT COM HOT COM Voice line 3 HOT COM HOT COM Voice line 4 HOT COM HOT COM Data line RS–485 A B GND GND 305 Power Source 144 5V DC, 15V DC (supplied from the main frame) Current Consumption 100mA (5V DC), 50mA (15V DC) Number of Audio Links 4 links Connection Format Multidrop system Transmitting System Data: RS-485 Voice: Base band Input/Output Level Voice: 0dB*, balanced Data: In compliance with RS-485 Standard Other Exchange number setting function Connection Terminals Main frame connection side: DIN connector (64-pin, male) Tie-line interface side: 4-pin × 4 (Voice line) 4-pin × 1 (Data line) Operating Temperatures 0°C to +40°C Weight 320g Accessories Connector (4-pin) × 5 Voice Security Intercom System VS-900TI Tie-Line Interface Card * 0 dB = 0.775V 78 VS-900RS Substation Interface Card * for RS-150/RS-160/RS-170/RS-180 Connects up to 16 substations per card. Equipped with two speech links, one link able to be used as a paging link with the paging input/output connected to an external amplifier. SPECIFICATIONS Power Source Line 1 for Substation Line 2 Voice Output Control Output HOT GND HOT GND A B C A B C A B C A B C Line 3 Line 4 Line 5 Line 6 A B C A B C A B C A B C Line 7 Line 8 Line 9 Line 10 A B C A B C A B C A B C Line 11 Line 12 Line 13 Line 14 A B C A B C A B C A B C Line 15 Line 16 305 For External Paging Amplifier 5V DC, 24V DC (supplied from the main frame) Current Consumption 5V DC: 200mA, 24V DC: 600mA Number of Lines Substation 16 lines Number of Links 2 links (one of 2 links is also used as a Paging Link.) Paging Output Unbalanced, –20dB signals to be sent to a paging amplifier. Paging Input Balanced, acceptable signal on the 25V line output from a paging amplifier. Conversation Method Half-duplex conversation by voiceoperated switch or simplex conversation by PTT switch Supply Power Maximum 1W per substation Other Call button detection function and speech link control function Connection Terminals Main frame connection side: DIN connector (64-pin, male) Substation connection side: Two-core shielded cable (3-pin) × 16 Paging output/paging input: 4-pin Operating Temperatures 0°C to +40°C Weight 550g Accessories Connector (3-pin) × 16, Connector (4-pin) × 1 144 VS-910RS Substation Interface Card * for RS-190 (Full-Duplex Substation) The VS-910RS Substation Interface Card is used to connect the Full-Duplex Substation by way of 2 sets of twisted pair cables. Up to 16 Full-Duplex Substations can be connected per card. The VS-910RS has 2 speech paths, either of which can be used for substation paging. SPECIFICATIONS For RS-190 Line2 A B C D Line4 Line5 A B C D A B C D Line6 Line7 A B C D A B C D Line8 Line9 A B C D A B C D Line10 Line11 A B C D A B C D Line12 Line13 A B C D A B C D Line14 Line15 A B C D A B C D Line16 A B C D Line3 A B C D Power Source 305 A B C D Line1 Voice Security Intercom System 144 79 5V DC, 24V DC (supplied from the main frame) Current Consumption 5V DC: 200mA 24V DC: 600mA (maximum during nomal use), 1.5A (maximum when 16 lines are simultaneusly shorted) Number of Lines Substation 16 lines Number of Links 2 links (one of 2 links is also used as a Paging Link.) Coversation Method Full-duplex conversation or Half-duplex conversation by voice-operated switch Audio Output Maximum 1W per substation Supply Power Maximum 20V/30mA per substation Control System Two-way dial pulse width system (call, restoration, external control, etc.) by current loop Connection Terminals Main frame connection side: DIN connector (64-pin, male) Substation connection side: 4-pin × 16 Connection Monitoring Line connection detection, line short Function circuit/open circuit/failure detection and communication irregularity detection Operating Temperatures 0°C to +40°C Weight 700g Accessory Connector (4-pin) × 1 Maxmum cable distance Cable Type AWG24 AWG22 AWG20 (ø0.52mm) (ø0.65mm) (ø0.82mm) Distance 1km 1.5km 2km MS-900 Master Station MS-900 can make calls to or receive calls from the substation or the master station (telephone). 21 125 83.5 60 SPECIFICATIONS 80.5 94 Wall mounting bracket Wall mounting bracket MS-900 8.5 Rear panel 5.5 74.5 216 208 Dimensional diagram for mounting the attached wall mounting bracket 24V DC (supplied from the main frame) 60mA Duplex or semi-duplex conversation 300 to 3.400Hz Dynamic type, 150Ω Electret condenser microphone Dynamic type, 8Ω, ø57mm, 0.6W Membrane switch 12 digits LCD 8 keys 2-step selection slide switch Volume, 0 to +12dB Desk-/wall-mountable Twisted pair cables/2-pair Line output: 6-position 4-contact modular jack External speaker output: 2-pin screw terminal (8Ω/0.6W) Operating Temperatures 0°C to +40°C Finish ABS resin, pale white Dimensions 216 (W) × 74.5 (H) × 213 (D)mm Weight 940g Accessories Wall mounting bracket × 1, Connection cord (3m) × 1, Wood screw × 2 213 69.5 Power Source Current Consumption Talk System Talk Frequency Handset Microphone/Speaker Handsfree Microphone Station Speaker Key Pad Display Auto Dialing Key Station Speaker Volume Control Handset Speaker Volume Control Installation Method Wiring Connection Terminals RS-150 Substation (Indoor Type) SPECIFICATIONS 83.5 120 43.5 48.5 46 120 Black (C) Brown (B) 90 Orange (A) Finish Dimensions Weight Accessories 1W 625Ω (1W/25V) 82dB 300 to 4,000Hz (minimum 72dB) 4cm dynamic Resin-made push button –10°C to +50°C (Temperature range not to freeze the speaker and switch) Stainless steel (SUS304), hairline 120 (W) × 120 (H) × 48.5 (D)mm 410g Oval head screw × 4 RS-160 Substation (Indoor Vandal-Resistant Type) Voice Security Intercom System Rated Input Rated Impedance Output Sound Pressure Level Frequency Response Internal Speaker Call Switch Button Operating Temperatures 2 SPECIFICATIONS Rated Input Rated Impedance Output Sound Pressure Level Frequency Response Internal Speaker Call Switch Button Operating Temperatures 83.5 120 3 46 120 52.5 57.5 Black (C) Brown (B) 90 Orange (A) Weatherproof coating Finish Dimensions Weight Accessories 1W 625Ω (1W/25V) 82dB 300 to 4,000Hz (minimum 72dB) 4cm dynamic Metal push button –10°C to +50°C (Temperature range not to freeze the speaker and switch) Stainless steel (SUS304), hairline 120 (W) × 120 (H) × 57.5 (D)mm 540g Oval head screw × 4 80 RS-170 Substation (Outdoor Vandal-Resistant Type) SPECIFICATIONS 83.5 120 3 46 120 52.5 57.5 Black (C) Brown (B) 90 Orange (A) Rated Input Rated Impedance Output Sound Pressure Level Frequency Response Internal Speaker Call Switch Button Weather-Resistant Coating Operating Temperatures Finish Dimensions Weight Accessories 1W 625Ω (1W/25V) 82dB 300 to 4,000Hz (minimum 72dB) 4cm dynamic Metal push button Printed circuit board –10°C to +50°C (Temperature range not to freeze the speaker and switch) Stainless steel (SUS304), hairline 120 (W) × 120 (H) × 57.5 (D)mm 540g Oval head screw × 4 rear RS-180 Substation (Outdoor Vandal-Resistant Type with Control Output) SPECIFICATIONS Rated Input Rated Impedance Output Sound Pressure Level Frequency Response Internal Speaker Call Switch Button Call LED Control Output 83.5 120 3 52.5 57.5 46 120 Black (C) Brown (B) Orange (A) 90 White(Open collector: Hot) Blue(Open collector: COM) Weatherproof coating rear 1W 625Ω (1W/25V) 82dB 300 to 4,000Hz (minimum 72dB) 4cm dynamic Metal push button (red top: ø20) Red Open collector output: 24V DC, 5mA (The open collector output is kept turned on till the conversation is finished after the call button was pressed.) Printed circuit board Weather-Resistant Coating Operating Temperatures –10°C to +50°C (Temperature range not to freeze the speaker and switch) Finish Stainless steel (SUS304), hairline Dimensions 120 (W) × 120 (H) × 58.5 (D)mm Weight 570g Accessories Oval head screw × 4 RS-190 Full-Duplex Substation (Indoor Type with Control Output) SPECIFICATIONS 1W 500Ω 4cm cone-type Open collector output: 24V DC, 30mA (The open collector output is kept turned on till the conversation is finished after the call button was pressed.) Operating Temperatures –10°C to +50°C (Temperature range not to freeze the speaker and switch) Panel: Stainless steel (SUS304), hairline Finish Call button: Resin 120 (W) × 120 (H) × 58.5 (D)mm Dimensions 465g Weight Accessories Box mounting screw (No.6–32UNC × 8) × 4, Box mounting screw (M4 × 25) × 4 Maxmum cable distance Cable Type AWG24 AWG22 AWG20 (ø0.52mm) (ø0.65mm) (ø0.82mm) Distance 1km 1.5km 2km Rated Input Rated Impedance Internal Speaker Control Output 83.5 120 72.1 2 53 58.5 Voice Security Intercom System 46 120 85 RS-191 116 46 70 48 SPECIFICATIONS 220 83.5 115 Option Handset Handset Receiver Handset Transmitter Internal Speaker Operating Temperatures Finish Dimensions Weight Accessories 81 Unit: mm Dynamic type Electret condenser type 4cm cone-type 0°C to +40°C (Temperature range not to freeze the speaker and switch) ABS resin, pale white 116 (W) × 220 (H) × 70 (D)mm 330g Box mounting screw (No.6–32UNC × 8) × 4, Box mounting screw (M4 × 25) × 4 VS-900DI* Direct Select Control Card SPECIFICATIONS Power Source Maximum Cable Length to Exchange Maximum Number of Connectable VS-900DI Cards Function Key Input Communication Line In-use Indication Output Electret Microphone Input Speaker Output Headset Connection 305 139.5 6.4 6–ø4 6.4 144 PC Interface Usable Cable Operating Temperatures Weight Accessories 16.5 1.8 133.4 24V DC, 1A 1.5km (including the additional master station line from the VS-900DI) when the cable gauge is AWG22 4 cards per exchange, 64 cards per system (16 tie-lined exchanges) One each of (C), (PTT), (XFER) and (TEST), keys, Dry contact, 8-pole screwless terminal Dry contact, 5V DC/0.5mA Contact resistance: 50Ω or less 1 line for VS-900 exchange (VS-900MS card) and 1 line for MS-900 master station, 16-position 4-contact modular jack for each line Open collector output, 24V DC/ approx. 100mA, 2-pole screwless terminal Microphone sensitivity: –75 to –65dB*, phantom power supply (power supply can be cut off), 2-pole screwless terminal Speaker impedance: 8Ω Output terminal: 2-pole screwless terminal Microphone sensitivity: –75 to –65dB* Speaker impedance: 200 to 400Ω Detection jack contact input (Det.): 5V DC, 10mA Contact resistance:10Ω or less, 8-pole screwless terminal (Headset can also be turned on/off using the manual switch instead of the jack contact input.) RS-232C D-sub connector (9 poles, female type) Bared-core length: 5 to 6mm Cross section area: 0.14 to 2.5mm2 0°C to +40°C 350g Ferrite clamp × 2, Modular cord (3m) × 1 * 0 dB = 1V VS-910DI* Direct Select I/O Card SPECIFICATIONS Power Source Maximum Number of VS-910DIs per VS-900DI Maximum Number of Ports per VS-910DI Maximum Number of Ports per Full VS-910DI-Mounted System Switch Input Open Collector Output Relay Output 139.5 6.4 15.5 or less 305 82.8 74.9 51.816 2.159 Operating Temperatures Weight 32 switch inputs (for calling and response switch operation) 32 open collector outputs (for LED indication of incoming and outgoing calls) 32 relay outputs (call-or response-activated relay output) 1024 switch inputs (for calling and response switch operation) 1024 open collector outputs (for LED indication of incoming and outgoing calls) 1024 relay outputs (call-or response-activated relay output) 32 inputs (for custom-made direct select key operation for calling or response) dry contact, 5V DC, 0.5mA Contact resistance: 50Ω or less, 50-pole "CHAMP®" IDC connector (Amphenol connector) 32 outputs (for LED indication of incoming and outgoing calls) 24V DC, approx. 100mA, 50-pole "CHAMP®" IDC connector (Amphenol connector) 32 relay outputs, call-or response-activated relay output, normal open, 24V DC, 1A, 50-pole "CHAMP®" IDC connector (Amphenol connector) 0°C to +40°C 460g * The VS-900DI Direct Select Control Card and VS-910DI Direct Select I/O Card are interface cards that connect to the VS-900 Exchange to enable calling-station indication output, direct select input, and external equipment control output functions. Voice Security Intercom System 1.6 100 133.4 15 or less 6.4 144 6–ø4 24V DC, 1A 32 PU-200 Power Transformer Unit SPECIFICATIONS 160 140 120 0 ø1 Output Voltage Output Current Finish Dimensions Weight Accessories NCU Type: 110V/120V AC, 50/60Hz SEM Type: 220V/230V AC, 50/60Hz 20V AC 2.5A Color steel plate, ivory 160 (W) × 68 (H) × 178 (D)mm 2.8kg Mounting brackets × 2 Fuse (250V, 2A) × 1 Fuse (125V, 4A) × 2 Round head wood screw (3.5 × 25) × 4 65 68 18 115 145 165 178 Power Source 4 Fitting Hole 82 VS-900SC Site Connector TOA's VS-900SC Site Connector is used to connect the VS-900 system exchanges to the fiber optical interface. SPECIFICATIONS Power Source 20V AC (supplied from the power transformer unit, under 250mA) 24V DC 4 links Number of Links 0dB*, 600Ω, balanced (transformer) Input 0dB*, 600Ω, balanced (transformer) Output Rack- and wall-mountable Installation Method Voice line side: 4-pin × 3 (voice line)/1 link Connection Terminal PU-200 connection terminal: 2-pin 24V DC input terminal: 4-pin Operating Temperatures –10°C to +40°C Finish Panel, Case: Pre-coated steel plate, black Dimensions 420 (W) × 88.4 (H) × 238 (D)mm Weight 3.55kg Accessories Rack mounting bracket × 4, Rack mounting screw × 4, Fiber washer × 4, Wall mounting bracket × 2, Wall mounting screw (4.1 × 20) × 4, Link Plate*2 × 2, Link plate fixing screw × 2, Bracket mounting screw × 8, Connector (4-pin) × 13, Connector (2-pin) × 1 * 0 dB = 1V *2 Enables to link VS-900SC with VS-900MF 76.2 88.4 482 465 420 4-6×10 (without front panel) 238 236 PN-100B Rack Mount Panel for PU-200 SPECIFICATIONS 10 Mounting Capacity Finish Dimensions Weight 101.6 177 4 –7x10.5 Up to 2 PU-200s Color steel plate, Black 483 (W) × 177 (H) × 10 (D)mm 0.7kg 37.7 466 483 99 YC-303 Main Frame Wall Mounting Bracket SPECIFICATIONS 200 440 Finish Dimensions Weight Accessories 290 338 391.4 Steel, Black, electrodeposition paint 391.4 (W) × 440 (H) × 58 (D)mm 2.1kg Main frame mounting screw × 4, Wall mounting screw × 4 58 Voice Security Intercom System Main frame VS-900MF 36.2 66 78 78 78 YC-302 Back Box (2-gang) for RS-150/160/170/180/190 3–ø21.5 knock-out hole 2–ø27.1 knock-out hole SPECIFICATIONS 102 73 83.5 106 1–M4 Quantity packed per display carton Finish Dimensions Weight 102 83 SPHT, MFZn4 (glazed chromate) Outlet box: 102 (W) × 102 (H) × 44 (D)mm Cover: 106 (W) × 106 (H) × 13 (D)mm 370kg 2–M4 44 13 46 92 106 10 pieces 4–ø27.1 knock-out hole Outlet Box 4–ø21.5 knock-out hole Unit: mm VS-900 SYSTEM CONFIGURATION EXAMPLE SYSTEM EXAMPLE Outside line SYSTEM SPECIFICATIONS ■ Exchange Method: PCM and space division ■ Control Method: Common stored program control ■ Maximum Cable Length Exchange to Master station: 1.5km (22AWG) Exchange to Substation: 800m (22AWG) (RS-190: 1,5km) Exchange to telephone: less than 500Ω (loop impedance) Exchange to Exchange: 1.0km (22AWG) (total extension length) ■ Wiring Master station: 2 twisted pairs Substation: 2-core shielded (RS-190: 2 twisted pairs) Telephone: 1 twisted pair Exchange to Exchange: 2-core shielded for Data, 2 twisted pairs for Audio (per link) ■ Frequency Response: 300 – 3,400Hz ■ Conversation Method Substation to Master station: Voice Switch or PTT-activated talk-back Master station to Master station: Full-duplex handset communication ■ Power Requirements Exchange: AC mains (PU-200) or 24V DC VS-900DI/VS-910DI: 24V DC ■ Operating Temperature Exchange and Master station: 0 to 40°C Substation: –10 to 50°C PC (for programming and system maintenance) External paging equipment Amplifier VS-900 Exchange VS-900 Exchange Substation paging amplifier* Speaker Substations Master stations Speaker Speaker * Substation paging needs an external amplifier. ex: TOA A-1031 or similar amplifier. Matching transformer such as the TOA MT-502U needed (Part Number 514-04-013-20). Master Stations*1 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 Sub-stations*2 64 128 192 256 320 384 448 512 576 640 704 768 832 896 960 1024 VS-900MF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PU-200 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 VS-900MS/AL 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 VS-900RS/VS-910RS 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 VS-900CO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VS-900AF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VS-900TI 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Voice Security Intercom System SYSTEM CONFIGURATION *1 TOA MS-900 Master Station or analog (DTMF) telephone which complies with the FCC requlation Part 68 (supplied by others). *2 RS-150, RS-160, RS-170, RS-180, RS-190 84 VS-900 CALL-RELATED FUNCTION GROUP CALL SCAN MONITOR A designated group of up to 16 master stations or telephones can be called from any substation, which is answered from any called master station (telephone). Any master station can scan a designated group of substations for audio monitoring of each substation. [System pre-programming] First, one of master stations (telephones) in a group must be programmed as a representative station, and the rest as member stations. Then, a calling substation must be programmed to call the representative station. TRANSFER-RELATED FUNCTION [System pre-programming] (1) Substations to be monitored (up to 16) can be registered for each master station in system programming. (2) Monitor interval times of 1 - 99 seconds (in 1 second units) for each master station can be registered in the system programming. PAGING-RELATED FUNCTIONS CALL TRANSFER ZONE PAGING (1) Call transfer A master station (or telephone) can transfer the conversation partner to another master station (or telephone). (2) Call Hold and Call Back These functions enable the master station (or telephone) to temporarily put the current conversation on hold (Call Hold), and return to the original conversation (Call Back) after talking with a third party. Permits paging to up to 19 individual zones (01 – 19) established by combining multiple substations with external public address system equipment. Two or more individual zones can simultaneously be selected. Note: Master station and telephone operation differs. CALL FORWARDING-RELATED FUNCTIONS CALL FORWARDING When away from one's desk, incoming calls can be automatically forwarded to another receiving station. The receiving station*1 number can be registered at the original station (forwarding station). It is also possible to active this feature from the destination receiving station. [System pre-programming] To use this function, enable the Call Forwarding function in system programming. TIME-BASED CALL FORWARDING All incoming calls to the original station*1 (forwarding station) can be automatically rerouted to the designated master station*1 (receiving station) during a specific period of the day. [System pre-programming] (1) To use this function, the Time-Based Call Forwarding function must be enabled in system programming. (2) The forwarding interval (start and end times) can be registered in the system programming. (Registration can only be performed for an entire exchange. Different times cannot be set for different stations on the same exchange.) NO-ANSWER CALL FORWARDING Voice Security Intercom System MONITOR-RELATED FUNCTION Calls to the original station*1 (forwarding station) are automatically rerouted to the designated receiving station*1 if the called party does not respond within a preset period of time. [System pre-programming] (1) To use this function, the No-Answer Call Forwarding function must be enabled in system programming. (2) Register a variable "no-response" time of 1 - 99 seconds (in 1 second units) in the system programming. (Registration can only be performed for an entire exchange. Different times cannot be set for different stations on the same exchange.) BUSY CALL FORWARDING Calls to a busy station*2 are automatically forwarded to a designated station*2. [System pre-programming] To use this function, the Busy Call Forwarding function must be enabled in system programming. *1 Both the forwarding and receiving stations must be either master stations or telephones. Calls cannot be transferred to a substation. *2 The station which forwards calls (forwarded station) and the station to which calls are forwarded (receiving station) must be either a master station or a telephone. Calls cannot be forwarded to a substation. [System pre-programming] (1) The number of zone number digits (1 or 2 digits) can be registered in system programming. Single digit: Zone Nos. 1 - 9 Double digit: Zone Nos. 01 - 19 (2) Substation numbers and selective external public address equipment outputs to be included in each zone can be registered in the system programming. Up to 1,024 substations and up to 16 selective outputs can be registered per zone. Note: Only 1 voice output is made available for paging to external equipment. It is impossible for 2 or more persons to simultaneously initiate paging. ALL-ZONE PAGING Paging calls can be simultaneously made to substations and external public address equipment in the all programmed zones. (Paging calls are not made to substations and external public address equipment not assigned to zones.) [System pre-programming] (1) The number of digits (1 or 2) of an all-zone paging access number ([0] or [0][0]) can be registered in system programming. (2) Substation numbers and selective external public address equipment outputs to be included in each zone can be registered in the system programming. Up to 1,024 substations and up to 16 selective outputs can be registered per zone. EMERGENCY PAGING Paging calls can be made to all connected master stations, substations, and external public address equipment simultaneously. [System pre-programming] Master stations that can place Emergency Paging calls must be registered in the system programming. EXTERNAL SOURCE DISTRIBUTION By activating the input, external sound sources can be distributed to preprogrammed paging zones. Permits source distribution to up to 19 individual zones (01 - 19) established by combining multiple substations with external public address system equipment. Two or more individual zones can simultaneously be selected. [System pre-programming] Up to 9 (19) paging zones can be registered for each activation input (up to 4 inputs) in system programming. (Up to 1,024 substations and up to 16 selective external public address equipment outputs to be included in each zone are registered in the Zone Paging system programming.) PAGING TIME-OUT Paging calls that exceed a set time limit are automatically terminated. (This function is used mainly to prevent the line from being occupied because the user forgot to turn off the function.) The Time-Out function is disabled when an emergency paging call is placed. [System pre-programming] • Program whether to [Enable] or [Disable] the Paging Time-Out function. • Paging time-out (10 - 990 seconds in 10 second units) common to both Individual Zone and All-Zone Paging functions can be registered in the system programming. PAGING REDIAL 85 This function permits redialing the last-paged zone by simple key operations. CONVENIENT FUNCTIONS TELEPHONE-RELATED FUNCTIONS OUTGOING TELEPHONE CALLS OUTSIDE LINE CALL FORWARDING Outside telephone lines can be connected to the VS-900 system, permitting the system's master stations to make or receive outside line telephone calls. All calls can be automatically rerouted to the designated receiving telephone by registering the outside line access number at the original master station or telephone. [System pre-programming] A single-digit outside line access number ([0]-[9]) must first be programmed. INCOMING OUTSIDE LINE CALLS (DIRECT-IN LINE) [System pre-programming] (1) To use this function, the Call Forwarding function must be enabled in system programming. (2) The receiving telephone number can individually be registered for each master station (or telephone) in the system programming. When an outside telephone call is received, a call tone sounds at the registered representative station* and up to 3 member stations*. TIME-BASED OUTSIDE LINE CALL FORWARDING All incoming calls to the original master station or telephone can be automatically rerouted to the designated outside line telephone during a specific period of the day. [System pre-programming] One representative station* and up to 3 member stations* must be registered in the system programming to receive outside line calls. * Both the representative and member stations must be master stations or telephones. Note: Both the representative and member stations must be connected to the same exchange connected to the outside telephone line. INCOMING OUTSIDE LINE CALLS (DIRECT-IN DIALING) Outside line calling parties can be connected to a desired master station (telephone) or substation by directly dialing the station number. [System pre-programming] (1) To use this function, the Call Forwarding function must be enabled in system programming. (2) Register the receiving outside line telephone number individually for each master station (or telephone) in the system programming. (3) The forwarding interval (start and end times) can be registered in the system programming. (Registration can only be performed for an entire exchange. Different times cannot be set for different stations on the same exchange.) OUTSIDE LINE CONNECTION TIME-OUT • The duration of connection with the outside line telephone can be limited to automatically terminate conversations. • When the limited time is reached, a warning signal tone is transmitted to both the calling and called parties to terminate the conversation. [System pre-programming] (1) Program whether to [Enable] or [Disable] the Connection Time-Out function. (2) Set a connection time limit of 1 – 99 minutes in 1 minute unit. CONFERENCE-RELATED FUNCTIONS THREE-PARTY CONFERENCE (INDIVIDUAL CALL CONFERENCE) Any master station (or telephone) can individually call other master stations (telephones) to hold a 3-party conference. EMERGENCY CONFERENCE OUTSIDE LINE CONVERSATION RECORDING • Connecting an external recording device permits recording of outside line telephone conversations. • The external control output is made when the outside line telephone is connected, and is broken when the telephone is disconnected. To enable conferences among up to 4 parties in emergency situations, master stations or telephones can call other registered master stations or telephones with a simple operation. [System pre-programming] To use this function, up to 3 master stations or telephones must be individually assigned to each master station in the system programming. VS-900 OPTICAL LINK CONNECTION EXAMPLE (useing VS-900SC) O.D.L. Fiber optic cable VS-900SC PU-200 Power Transformer unit VS-900TI Tie-Line unit O.A.L. O.A.L. Power supply O.D.L. O.D.L. VS-900MF VS-900TI Tie-Line unit O.A.L. Voice Security Intercom System O.A.L. Fiber optic cable O.D.L. Control signal line Audio signal line VS-900MF VS-900TI Tie-Line unit VS-900MF * O.A.L. (Optical Analog Link): Optical/audio signal converter O.D.L. (Optical Data Link): Optical/digital signal converter 86 PC INTERFACE SOFTWARE DESCRIPTION Conversation and broadcasting functions can only be used by programming individual line assignments for each facility, station numbering schedules, function details and other data into the exchange before the system is actually used. To perform such settings, a personal computer loaded with dedicated software needs to be connected to the exchange. This dedicated software enables general control and maintenance settings as well as system programming functions. Notes Some functions to be registered at master stations cannot be enabled without prior system programming. SYSTEM REQUIREMENTS OS: Microsoft® Windows NT® Workstation 4.0 Service Pack 5/ Windows 2000®/Windows XP® CPU: Pentium® 200MHz or more Memory: 64MByte or more Hard disk: Free space of 50MByte or more Monitor: Larger than 14.1 inches Resolution: 640 × 480 pixel, 256 colors or more Other: RS-232C port, 3.5-inch FDD SYSTEM PROGRAMMING (SETTING ITEMS) System Setting • Number of Exchanges • Station Number Digit • Tie-Line Connections • Exchange Station Number Assignment Line Setting (1) Master station/telephone setting Registers the following contents designating the exchange number (1 - 16 or ALL). • Station Number • Station Name • Access to Outgoing Calls • Emergency Paging • "Outside Line Call Forwarding" Receiving Telephone Number • "Call Forwarding" Receiving Station* • "Time-Based Call Forwarding" Receiving Station* • "Busy Call Forwarding" Receiving Station* • "No-Answer Call Forwarding" Receiving Station* Function Setting (1) Group call setting Registers the following contents designating the representative master station/telephone. • Member Station Exchange Number • Member Station line Number (2) Call forwarding & time-out settings Registers the following contents designating the exchange number (1 - 16). • Call Forwarding • Time-Based Call Forwarding • Time-Based Call Forwarding Start Time • Time-Based Call Forwarding End Time • Busy Call Forwarding • No-Answer Call forwarding • Call Time-Out • Conversation Time-Out (3) Scan monitor setting Registers the following contents designating the master station. • Monitoring Time • Monitoring Substation Exchange Number • Monitoring Substation Line Number • Monitoring Substation Number • Monitoring Substation Name (4) Paging setting Registers the substations assigned to the zone designating the exchange number (1 - 16). • Zone Number Digit • Paging Time-Out • Zone (5) Public address system setting Registers the control outputs assigned to the zone designating the exchange number (1 - 16). • Zone (6) External source distribution setting Registers zones to the control input designating the exchange number (1 -16). • Zone (7) Emergency conference setting Registers the following contents designating the master station. • Member Station Exchange Number • Member Station Line Number • Member Station Number • Member Station Name (8) Direct select setting (Relay output from the VS-910DI card) Registers the following contents designating the exchange number (1 - 16). • Control Output Mode Voice Security Intercom System * This setting can be performed at the master station as well. 87 (2) Substation setting Registers the following contents designating the exchange number (1 - 16 or ALL). • Station Number • Station Name • Called Station Exchange Number • Called Station Line Number • Called Station Number • Called Station Name • Call Priority (3) Outside line setting Registers the following contents designating the exchange number (1 - 16). • Outside Line Connection Time-Out • Outside Line Name • Outgoing Call Access Number • Direct-In Dialing • Direct-In Line • Receiving Station MAINTENANCE/CONTROL FUNCTIONS (1) Remote Dialing Dialing operations can be remotely performed from a PC instead of the master Station by designating the exchange and master station number. (2) Log Data The operating log of each exchange can be read, printed out or stored on hard disk. (3) Upload/Download Data can be transmit or received. (4) Print Out The exchange setting contents are print out. (5) PC Port Setting Setting are made for the connection method and COM port between PC and exchange. NETWORK AUDIO ADAPTER NX-100 DESCRIPTION FEATURES The NX-100 Network Audio Adapter can transmit high-quality audio signals and such control data as serial data over IP networks, such as LAN or Internet, in real time. It is especially useful when transmitting audio signals to remote locations, as Internet use keeps running costs lower than the use of dedicated lines. With the use of an optional rack-mounting bracket, it can be mounted in an EIA Standard rack (1 unit size). ● If there is no network delay, audio signals have only a minimal millisecond delay. APPEARANCE AND DIMENSIONAL DIAGRAM ● Control data including contact and serial data can also be transmitted along with the audio signals. ● Two-way audio signal transmission is possible with a single NX-100 unit as every unit is equipped with an audio input and output. ● The multicast-capable NX-100 allows simultaneous transmission of audio signals to be made to multiple locations depending on transmission method: Unicast — up to 4 locations, Multicast — up to 64 locations. ● No audio signal degradation or loss, even when transmitting over crowded networks such as the internet. Rear View ● Greater data reliability using IP networks with the protocol's ability to prevent data problems during transmission. Front View ● The NX-100's contact input can initiate and terminate audio transmissions without having to use dedicated control equipment such as a PC. ● Hardware use ensures operational reliability over only software-driven applications. 210 42.5 46 Audio ● Using IP to transmit audio signals over the internet allows low cost operation rather than dedicated lines. ● The NX-100 is equipped with a DC input to allow operation on AC as well as DC. ● Software-driven operational menus enhance ease of use. 188 180 Unit: mm Network Audio Adaper Side View 88 NX-100 NETWORK AUDIO ADAPTERR SPECIFICATIONS Power Source 24V DC (plug-in screw connector) or AC adapter AD-246 (optional) or the equivalent Current Consumption 200mA (DC operation) Audio Input Audio Output 1 channel (transformer-isolated), –58dB* to 0dB*, balanced (MIC/LINE changeable, volume adjustable with volume control), 2kΩ, plug-in screw connector 1 channel (transformer-isolated), balanced, 600Ω, plug-in screw connector Frequency Response 50 – 14,000Hz (when sampling frequency is 32kHz) Distortion Control Input Under 0.3% (1kHz, when sampling frequency is 32kHz) 8 channels, no-voltage make contact input, open voltage: 12V DC, short-circuit current: 10mA, plug-in screw connector Control Output 8 channels, open collector output, withstand voltage: 30V DC, control current: 50mA max., plug-in screw connector Network I/F 10BASE-T/100BASE-TX, Auto-Negotiation Network Protocol Audio packet Transmission System Operating Temperature TCP/IP, UDP, HTTP, RTP Unicast (up to 4 simultaneous transmissions), Multicast (up to 64 simultaneous transmissions) 0°C to +50°C (0°C to +40°C when AC adapter is in use) Operating Humidity Under 90% RH (no dew condensation should be produced) Finish Steel plate, black, 30% gloss Dimensions Weight 210 ( W ) × 4 6 (H) × 188 (D)mm 1.2kg Accessory Bracket mounting screw × 8, CD (PC setting/operation software programe) × 1, Power supply screw connector plug × 1, Audio I/O screw connector plug × 2, Control I/O screw connector plug × 2, RS-232C connector cover × 1 Optional Components Rack mounting bracket: MB-15B-BK (for rack mounting one NX-100 unit) MB-15B-J (for rack mounting two NX-100 units) AC adapter: AD-246 * 0dB = 1V Note: When you need the AC adapter, be sure to consult your TOA dealer. GUIDELINES ON LINE BAND, SOUND QUALITY AND DELAY TIME (1) For LAN and dedicated lines Line Band Over 1.5 Mbps Voice Compression Audio Band Sampling No 50 - 14 kHz 32 kHz Yes 50 -14 kHz 32 kHz 128 kbps (Dedicated line, etc.) Yes 50 - 7 kHz 1 6 kHz 64 kbps (ISDN, etc.) Yes 50 - 3.4 kHz 8 kHz Voice Packet Loss Recovery Delay Time (sec) Silence 0.02 776 NOTES: 0.93 820 0.02 392 0.93 245 1. The following conditions apply to the side delay time values and required band: (1) Line band: 1.5 Mbps; Voice compression not used— Voice packet size: 128 bytes (2) Line band: 1.5 Mbps; Voice compression used— Voice packet size : 32 bytes (3) A voice packet size of 1,024 bytes assumed for all but the 1.5 Mbps Line band. Redundancy Silence Redundancy Silence Redundancy Silence Redundancy Band Used (kbps) 1.3 68 7.4 102 2.6 34 15 51 Network Audio Adapter (2) For the Internet 89 Line Band Voice Compression Audio Band Sampling Over 512 kbps (ADSL,etc.) Yes 50 -14 kHz 32 kHz 128 kbps (Dedicated line, etc.) Yes 64 kbps (ISDN, etc.) Yes 50 -7 kHz 50 - 3.4 kHz 50 - 3.4 kHz 16 kHz 8 kHz 8 kHz Voice Packet Loss Recovery Delay Time (sec) Band Used (kbps) Silence 0.6 136 Retransmission Silence 30 1.3 369 68 Retransmission Silence Redundancy 30 2.6 15 92 34 51 2. ‘‘Voice Packet Loss Recovery’’ is a processing function when the voice packet cannot be received owing to communications interference. (1) Silence: Sections without voice packets are processed as silence. (2) Redundancy: Enables the voice to be normally output for continuous losses of up to 8 packets. (3) Retransmission: Enables the voice to be normally output for continuous losses of up to 15 seconds. 3. ‘‘Required band’’ represents the bands required for voice transmission. When sending other data (such as serial data), the transmission band is separately required. ACCESSORIES BU-412 CR-131N/273/413/413-6 Blower Unit Cabinet Racks • Used as the top plate of the CR-131N/CR-272/CR-412/ CR-412-6. • Assures a constant temperature for sage amplifier operation. • Starts when rack temprature reaches 35°C and stops at 30°C. • Power Source: AC mains, 50/60Hz • Power Consumption: 17W 3 3 • Amount of Air Blower: Max. 1.98m /min. (50Hz), 2.15m /min. (60Hz) • Auto-Sensor: When temperatures in the racks 35°C; starts operating/35°C; stops • Dimensions (W × H × D): 300 × 7.2 × 240mm • Weight: 1.4kg CR-131N BK-013B/023B/033B CR-273 CR-131N Blank Panel CR-413 CR-413-6 • With 13-unit space • Dimensions (W × H × D): 546 × 674.5 × 420mm • Color: Pale ivory CR-273 • With 27-unit space • Dimensions (W × H × D): 566 × 1,364 × 435mm • Color: Ivory • BK-013B: 1-size BK-023B: 2-size BK-033B: 3-size • Color: Black CR-413 • Dimensions (W × H): BK-013B; 482.6 × 43.6mm/ BK-023B; 482.6 × 88.1mm/BK-033B; 482.6 × 132.5mm • Weight: BK-013B; 0.4kg/BK-023B; 0.75kg/BK-033B; 1.1kg • With 41-unit space • Dimensions (W × H × D): 566 × 2,000 × 435mm • Color: Ivory CR-413-6 PF-013B/023B Perforated Panel Cabinet Racks • Extra-deep type • With 41-unit space • Dimensions (W × H × D): 566 × 2,000 × 615mm • Color: Ivory • PF-013B: 1-size, PF-023B: 2-size • Color: Black YA-706 • Dimensions (W × H): PF-013B; 482.6 × 43.6mm/ PF-023B; 482.6 × 88.1mm • Weight: PF-013B; 0.15kg/PF-023B; 0.30kg • To support heavy rack equipment. • Applicable racks: CR-272, CR-412 & CR-412-6 Rack Supporting Runner (1 Pair) CC-P5BB CC-4900 CC-4902 BNC Plug BNCJ-RCAP Plug • BNC plug for connection with CCTV-associated devices. • Soldering type. • Compatible with 3C-2V or 5C-2V coaxial cables. • Set: 10 pieces •Conversion connector for BNC jacks and RCA pin plugs •Set: 10 pieces • Cord for 0.5 m 3C-2V coaxial cables and double-ended BNC plugs • Set: 10 cables CC-01BB BNC-BNCJ Plug • Intermediary connector for two BNC jacks • Set: 10 pieces Coaxial Cable with BNC Plugs (1m) • Cord for 1 m 3C-2V coaxial cables and double-ended BNC plugs • Set: 10 cables BNC Plug •BNC plug that allows solderless connection with coaxial cables. •Compatible with 3C-2V or 5C-2V coaxial cables. • Set: 10 pieces CC-05BB Coaxial Cable with BNC Plugs (5m) CC-4904 BNC T-Shape Connector • T-shape relay connector for BNC jacks • Set: 10 pieces Accessories CC-4903 CC-4901 Coaxial Cable with BNC Plugs (0.5m) • Cord for 5 m 3C-2V coaxial cables and double-ended BNC plugs • Set: 5 cables 90 METAL RACK-MOUNT SELECTION CHART NETWORK AUDIO ADAPTERR Accessories that Expand Your Business Potential Mountable Equipment Name Model No. Video Distributor C-VD6 × one or two units Manual Swicher CC-3011B CC-3021B × one or two units Cable Compensator CC-3331B × one or two units Appearance Rack-Mount Brackets Appearance MB-15B-BK (Mounting bracket × 2 Blank panel × 1) MB-15B-J Video Signal Adaptor CC-3350B × one or two units Remote Controller CC-5050B × one or two units Multiplexer C-MS91D (Mounting bracket × 2 Joint bracket × 2) MB-15B (Mounting bracket × 2) Remote Controller CC-5011B CC-5111B Camera Selector CC-5131B MB-23B Multiplexer C-MS161D (Mounting bracket × 2) MB-23B-BK (Mounting bracket × 2 Blank panel × 1) Metal Rack-Mount Selection Chart 24V AC Power Supply 91 CC-5941B × one or two units MB-23B-J (Mounting bracket × 2 Joint panel × 1) Setting Index B CC- M BK-013B .................................................... 90 BK-023B .................................................... 90 BK-033B .................................................... 90 BU-412 ...................................................... 90 CC-01BB ................................................... 90 CC-05BB ................................................... 90 CC-3011B ................................................. 69 CC-3021B ................................................. 69 CC-3331B ................................................. 72 CC-3350B ................................................. 73 CC-4510 .................................................... 48 CC-4520 .................................................... 48 CC-4900 .................................................... 90 CC-4901 .................................................... 90 CC-4902 .................................................... 90 CC-4903 .................................................... 90 CC-4904 .................................................... 90 CC-5011B ................................................. 51 CC-5050B ................................................. 50 CC-5111B ................................................. 53 CC-5120 .................................................... 53 CC-5131B ................................................. 55 CC-5521 .................................................... 46 CC-5525 .................................................... 46 CC-5550A ................................................. 46 CC-5941B ................................................. 51 CC-6000A ................................................. 44 CC-6080DMB ............................................ 45 CC-6080DMS ............................................ 45 CC-6080DMW ........................................... 45 CC-P5BB ................................................... 90 MB-15B ..................................................... 91 MB-15B-BK ............................................... 91 MB-15B-J .................................................. 91 MB-23B ..................................................... 91 MB-23B-BK ............................................... 91 MB-23B-J .................................................. 91 MS-900 ...................................................... 80 CC-A501DM .................................................. 7 C-AL80 ...................................................... 10 C-AP105 .................................................... 74 C-BC11 ..................................................... 49 C-BC21 ..................................................... 49 C-BC31 ..................................................... 49 C-BC41 ..................................................... 49 C-BC100K ................................................. 47 C-BC100T ................................................. 47 C-BC200H ................................................. 47 C-BC200K ................................................. 48 C-BC501 .................................................... 7 C-BC501K .................................................. 7 C-BC501T .................................................. 7 C-BC501U .................................................. 7 C-BL20 ...................................................... 50 C-CC351A ................................................. 23 C-CC354A ................................................. 24 C-CC504S .................................................. 6 C-CC554S .................................................. 5 C-CH100 ................................................... 43 C-CH100FH ............................................... 43 C-CH200 ................................................... 43 C-CH200FH ............................................... 44 C-CH210FH ............................................... 44 C-CV14-2 ................................................... 30 C-CV14-CS ................................................ 29 C-CV24-2 ................................................... 31 C-CV44-3 ................................................... 32 C-IF500 ..................................................... 10 C-MS91D ................................................... 61 C-MS161D ................................................. 59 C-PH200 .................................................... 45 C-QA40 ..................................................... 68 C-RM500 .................................................... 9 C-VD6 ........................................................ 71 CHCH-0808G ................................................. 37 CH-2610G ................................................. 37 CH-3808G ................................................. 37 CRCR-131N ................................................... 90 CR-273 ...................................................... 90 CR-413 ...................................................... 90 CR-413-6 ................................................... 90 CTCT-0312A ................................................... 39 CT-0312GA ................................................ 38 CT-0412A ................................................... 39 CT-0412GA ................................................ 38 CT-0812A ................................................... 39 CT-0812GA ................................................ 38 CT-2ZMGA ................................................. 36 CT-6ZMG ................................................... 35 CT-10VFG .................................................. 36 CT-10ZMG ................................................. 35 CT-21ZMG ................................................. 35 N N-CC1000 ................................................. 15 N-CC1110 ................................................. 16 N-SD1040 .................................................. 19 N-VT1010 .................................................. 17 NX-100 ...................................................... 88 P PF-013B .................................................... 90 PF-023B .................................................... 90 PN-100B .................................................... 83 PU-200 ...................................................... 82 R RS-150 RS-160 RS-170 RS-180 RS-190 RS-191 ...................................................... 80 ...................................................... 80 ...................................................... 81 ...................................................... 81 ...................................................... 81 ...................................................... 81 V VS-900AF .................................................. 78 VS-900AL .................................................. 77 VS-900CO ................................................. 78 VS-900DI ................................................... 82 VS-900MF .................................................. 77 VS-900MS .................................................. 77 VS-900RS .................................................. 79 VS-900SC .................................................. 83 VS-900TI .................................................... 78 VS-910DI ................................................... 82 VS-910RS .................................................. 79 W WH-4 ......................................................... 49 Y YA-706 ....................................................... 90 YC-302 ...................................................... 83 YC-303 ...................................................... 83 TOA Corporation URL: www.toa.jp/ Specifications are subject to change without notice. Printed in Hong Kong (0311) 833---
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021