Honeywell TH106 User's Manual

Honeywell TH106 User's Manual
400-106-009-A_69-2024 (Cadet TL6160) ENG.fm Page 1 Wednesday, November 1, 2006 9:54 AM
08160
TH106
TL6160
n
1.
Description
This programmable thermostat can be used to control an electric
heating system such as an electric baseboard heater, a radiant ceiling, a radiant floor, a convector, etc.
NOTE: Always keep the thermostat's vents clean and unobstructed.
n
Temperature
preset buttons
Appears when the
setpoint is displayed
Time and day
Temperature
Set the day
Set the time
Operating
mode icons
Program the
schedule
o
Temperature
preset icons
Skip a period
Connect the thermostat wires to the line wires and to the load
wires using solderless connectors for copper wires.
Heating power
indicator
Select the
operating mode
Periods
2-wire installation
Temperature
adjustment
buttons
The thermostat cannot be used under the following conditions:
•
•
•
•
The resistive load is greater than 16.7 A
The resistive load is less than 2 A
The system is driven by a contactor or relay (inductive load)
The system is a central heating system
4-wire installation
SUPPLIED PARTS:
•
One (1) thermostat
•
Two (2) 6-32 screws
•
Two (2) solderless connectors
o
Installation
2.
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK.
THE INSTALLATION MUST BE PERFORMED BY AN ELECTRICIAN.
All cables and connections must conform to the local electrical
code.
Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.
Install the thermostat onto an electrical box.
Install the thermostat about 5 feet high, on an inside wall facing
the heater.
Avoid locations where there are air drafts (such as the top of a
staircase or an air outlet), dead air spots (such as behind a
door), or direct sunlight.
Do not install the thermostat on a wall that conceals chimney or
stove pipes.
p
Push any excess wire back into the electrical box.
NOTE: If necessary, before re-installing the front component, configure the thermostat (see section 3).
q
Return power to heating system.
The thermostat wires are not polarized; either wire can be connected to the load or to the power supply.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
69-2024
1/11/06
1/3
400-106-009-A_69-2024 (Cadet TL6160) ENG.fm Page 2 Wednesday, November 1, 2006 9:54 AM
p
3.
Configuration
The configuration switches are on the back of
the thermostat. The factory settings are indicated by the gray cells in the following table.
s
SW1 Early Start a
SW2 Display format b
Off
On
°C / 24-hour
°F / 12-hour
SW3 Cycle length c
SW4 Not used
15 seconds
-
15 minutes
-
a. Early Start can be used in Automatic mode only. When this function is enabled, the thermostat calculates the optimal time to start
heating in order to obtain the desired temperature by the set time.
The thermostat re-assesses the start time daily based on the previous day’s performance.
b. If you change the temperature display format, the preset
temperatures ( , and ) will return to their default settings.
c. 15-second cycles should be selected in most cases as it provides
better temperature control. 15-minute cycles must be selected if
you have a fan-equipped heater or if 15-second cycles causes
light flickering (especially in rural regions).
q
4.
Power-up
Upon power-up, the thermostat is in manual mode ( ) and displays
the actual (ambient) temperature.
n
o
Automatic - The temperature is set according to the programmed
schedule. To place the thermostat in this mode, press Mode until is
displayed. The icons of the current period and preset temperature
are also displayed.
Temporary Bypass: If you modify the setpoint (by pressing the
, ,
or button) when the thermostat is in automatic mode,
the new setpoint will be used until the end of the current period.
When the next period starts, the temperature set for that period
becomes the new setpoint.
Manual - The programmed schedule is not used. The temperature
must be set manually. To place the thermostat in this mode:
n
o
t
Comfort temperature
Economy temperature
Vacation temperature
Comfort (when at home)
,
or
button.
7.
Schedule
The schedule consists of 4 periods per day which represents a typical weekday. You can program the thermostat to skip the periods that
do not apply to your situation. For example, you can skip periods 2
and 3 for the weekend.
Description
Associated temperature preset
Leave
Factory setting
Return
Sleep
The Comfort ( ) temperature is used in periods 1 and 3 and the
Economy ( ) temperature is used in periods 2 and 4. For example,
when the period changes from 1 to 2, the setpoint automatically
changes from Comfort setting ( ) to Economy setting ( ).
You can have a different program for each day of the week; i.e., each
period can start at different time for each day of the week. The
thermostat has been programmed with the following schedule.
Period
70 °F (21 °C)
Economy (when asleep or away from home) 62 °F (16.5 °C)
Vacation (during prolonged absence)
50 °F (10 °C)
To use the Comfort or Economy temperature, press the
or
button respectively. The corresponding icon will be displayed.
•
To use the Vacation temperature, press both
and buttons
simultaneously. The icon will be displayed.
Storing a preset temperature
To store the Comfort or Economy temperature:
Set the desired temperature using the or button. Press and
hold the appropriate button ( or ) for approximately 3 seconds until the corresponding icon is displayed. Press the Mode
button.
Setting
MO
TU
WE
TH
FR
SA
SU
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
6:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
8:00
AM
--:--
--:--
6:00
PM
6:00
PM
6:00
PM
6:00
PM
6:00
PM
--:--
--:--
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
10:00
PM
To modify the schedule:
n
Press Pgm to access the programming mode. Period 1 is
selected.
o
Press Day to select the day to program (hold for 3 seconds to
select the entire week).
p
Press Hour and Min to set the start time of the selected period,
or press Clear if you want to skip the period (--:-- is displayed).
Press Pgm to select another period, or press Day to select
another day. Then repeat step 3.
q
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
,
Wake
Temperature Setting
Intended use
is displayed.
Set the temperature using the
5.
Setpoint
The thermostat normally displays the actual temperature. To view the
setpoint, press the
or button briefly. The setpoint will appear for
the next 5 seconds.
To change the setpoint, press the
or
button until the desired
temperature is displayed. To scroll faster, hold the button.
Using a preset temperature
The thermostat has 3 preset temperatures:
•
Press Mode until
Press the Day button to set the day.
Icon
6.
Operating Modes
Period
Press the Hour and Min buttons to set the thermostat’s clock.
r
To store the Vacation temperature:
Set the desired temperature using the or button. Press and
hold both
and buttons simultaneously for approximately 3
seconds until the icon is displayed. Press the Mode button.
69-2024
1/11/06
2/3
400-106-009-A_69-2024 (Cadet TL6160) ENG.fm Page 3 Wednesday, November 1, 2006 9:54 AM
r
Press Mode to exit the programming mode.
NOTE: If no button is pressed for 60 seconds, the thermostat will
automatically exit the programming mode.
u
8.
Power Outage
In the event of a power outage, most settings are saved. Only the
time must be re-adjusted if the power outage lasts more than 2 hours.
The thermostat will return to the mode that was active prior to the
power outage.
v
9.
Troubleshooting
PROBLEM
SOLUTIONS
This condition is normal. Under normal
operation, the thermostat housing can
Thermostat is hot.
reach a temperature between 95 °F
(35 °C) and 104 °F (40 °C).
The measured temperature is below the
LO is displayed.
display range. Heating is activated.
The measured temperature is above the
HI is displayed.
display range.
Wrong temperature is
The thermostat is exposed to air draft.
displayed.
Eliminate the draft.
The thermostat was without power for
Wrong time is displayed.
more than 2 hours.
Temperature does not
Check that the thermostat is in Automatic
change according to the mode. Check the schedule and clock setprogrammed schedule. tings.
The thermal protection device on the
Display disappears and
heater is open. This can happen after a
reappears after a few
power failure or if the heater is obstructed
minutes.
by furniture or curtains.
Display looks faded
The heating system is less than the
when heating is actirequired minimum load. This thermostat
vated
cannot be used below that rating.
w
Technical Specifications
Power: 120/208/240 VAC, 60 Hz
Minimum load: 2 A (resistive only)
250 W @ 120 VAC
400 W @ 208 VAC
500 W @ 240 VAC
Maximum load: 16.7 A (resistive only)
2000 W @ 120 VAC
3500 W @ 208 VAC
4000 W @ 240 VAC
Display range: 32 °F to 140 °F (0 °C to 60 °C)
Display resolution: 1 °F (0.5 °C)
Setpoint range: 40 °F to 86 °F (5 °C to 30 °C)
Setpoint interval: 1 °F (0.5 °C)
Storage: -4 °F to 120 °F (-20 °C to 50 °C)
Certification: c UL us
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
10.
;
11.
Warranty
Honeywell warrants this product, excluding battery, to be free from
defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the
consumer. If at any time during the warranty period the product is
determined to be defective or malfunctions, Honeywell shall repair or
replace it (at Honeywell's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to
the place from which you purchased it, or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer
Care will make the determination whether the product should be
returned to the following address: Honeywell Return Goods,
Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN
55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This
warranty shall not apply if it is shown by Honeywell that the defect or
malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE
LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF
THIS PRODUCT. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so this limitation may not
apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF
THIS WARRANTY. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to
you.
This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN
55422 or call 1-800-468-1502. In Canada, write Retail Products
ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive,
Scarborough, Ontario M1V4Z9.
12.
Customer Assistance
If you have any questions about the operation of your thermostat,
please go to http://yourhome.honeywell.com, or call Honeywell
Customer Care toll-free at 1-800-468-1502.
®
As an ENERGY STAR partner, Honeywell has
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
69-2024
1/11/06
3/3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement