Installation/Operation Instructions and Warranty Information

Installation/Operation Instructions and Warranty Information
International
Fiber
Systems
Incorporated
Installation/Operation Instructions
and Warranty Information for Models...
VT1001
VT1001-R3
SERIES DESCRIPTION
This operating guide describes a family of International Fiber Systems, Inc. (IFS) fiber optic modems.
Not all modems have all of the features in this guide.
The VT1001 Series is designed to transmit video from two Closed Circuit Television (CCTV) cameras
over two multimode fiber optic cables to an IFS compatible dual channel (or two single channel) receiver(s).
PART NUMBER DESCRIPTION
VT1001 SERIES
VT1001
VT1001-R3
DUAL VIDEO TRANSMITTER: 850 nm, TWO MULTIMODE FIBERS
DUAL VIDEO TRANSMITTER: 850 nm, TWO MULTIMODE FIBERS, RACK MOUNT
COMPATIBILITY CHART
TRANSMITTER
VT1001
COMPATIBLE RECEIVER
VR1000, VR1001, VR1001-R3, VR1100,
VR1100-R3, VR2100, VR2100-R3
VR1000, VR1001, VR1001-R3, VR1100,
VR1100-R3, VR2100, VR2100-R3
VT1001-R3
POWER CONNECTION
(a) Stand-alone Modules:
VT1001
12 VDC INPUT
PIN 1
PIN 2
+ 12 VDC
GROUND
(b) –R3 Modules:
All “-R3” models receive power from the back plane of the R3 rack. Insert the “-R3” unit into any
available R3 rack slot such that the female 3-pin connector on the back of the module engages the companion
male connector of the back plane. The red power LED will glow when voltage is applied to the unit.
International Fiber Systems, Inc.
16 Commerce Road • Newtown, Connecticut 06470 USA • Tel: 203.426.1180 • Fax: 203.426.3326
VT1001 Rev: 1 05/27/98
CAMERA CONNECTION
Attach two 75 ohm coaxial cables (terminated with BNC connectors) from two separate cameras’ BNC
connectors to the two "VIDEO IN" BNC connectors on the VT1001 series module.
FIBER OPTIC CONNECTION
Select a quality fiber optic cable containing either 50/125 or 62.5/125 fiber and attach a ST style fiber
optic connector using the connector manufacturer's recommended procedures. Connect the fiber optic
cable to the ST connector marked "OPTICAL OUT" on the VT1001 series module.
MOUNTING STAND-ALONE UNITS
Hold the VT1001 module against the mounting surface and mark the locations of the keyhole slots on the
rear mounting brackets. Install mounting screws into keyhole marks, allowing leeway under the screw heads
for the box to be mounted. Mount the brackets over the screws, slide, and tighten.
VIDEO LINK OPERATION
Make sure that power is applied to the VT1001 series module, camera, and video monitor. Ensure that
the camera and monitor are turned on, and that any lens cover on the camera has been removed. Verify that
coaxial cables and fiber optic cable are properly connected (i.e., the same fiber connects to the video input and
output on transmitter and receiver). Successful link operation should be visible at this point as witnessed by a
good quality video picture on the monitor.
International Fiber Systems, Inc.
16 Commerce Road • Newtown, Connecticut 06470 USA • Tel: 203.426.1180 • Fax: 203.426.3326
VT1001 Rev: 1 05/27/98
Simplex multimode
fiber optic cables
To VR1000, VR1001,
VR1100 and VR2100
series module
}
VT1001
DUAL VIDEO TRANSMITTER
OPTICAL OUT A
VIDEO IN A
SYNCH DETECT A
SYNCH DETECT B
ifs
International
Fiber
Systems
OPTICAL OUT B
Incorporated
Coax cable
203.426.1180
VIDEO IN B
POWER
GROUND -2
POWER
+12 VDC -1
Black wire
Black with
white stripe
Video source
Video source
Note: To verify the number of fiber optic cables, and fiber optic cable types
of other models within this series, check the compatibility chart and part
number description sections within this manual.
International Fiber Systems, Inc.
LIFETIME WARRANTY
INTERNATIONAL FIBER SYSTEMS, INC. (IFS) warrants to the
original purchaser that all IFS manufactured products shall be free from
defects in material or workmanship at the time of shipment.
LABOR AND PARTS: From the date of purchase to the original user, if
this product is determined to be defective, IFS will repair or replace the
product at no charge.
Our obligation under this warranty is limited only to the repair or
replacment of any of our products, providing said products are used within
the specified ratings and applications, and said products are applied in
accordance with good engineering practices, and providing said products are
proved by our examination to be defective.
This warranty does not extend to any IFS products which have been subject
to acts of God, accident, misuse, abuse, neglect, improper application or
installation, improper operation or maintenance, connection to an improper
voltage supply or to materials which have been altered or repaired outside of
an authorized IFS factory repair center.
This warranty shall constitute the fulfillment of IFS’ liability. IFS shall not
be liable for any incidental or consequential damages or breach of any
express or implied warranty on this product, except to the extent prohibited
by applicable law. Any implied warranty of merchantability or fitness for a
particular purpose of this product is limited in duration to the duration of
this warranty.
Exclusions:
Power transformers, batteries, or cosmetic damage.
16 COMMERCE RD • NEWTOWN, CT 06470 • TEL: 203.426.1180 • FAX: 203.426.3326
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement