Multi-Biometric Installation Guide

Multi-Biometric Installation Guide
!
Multi-Biometric Installation Guide
Version: V1.1
Warning: No operating with power on
Date: Nov. 2011
3.Lock Connection
1. Equiment Installation
(1) Shares power with the lock:
+
In st ru ct io n fo r th e Mo un ti ng P ap er
BELLBELL+
SEN
GND
DC12V
Be fo re t he d ev ic e is f as te ne d, p le as e st ic k th e pa pe r to t he p la ce w he re y ou
wa nt t o in st al l it , th en m ak e ho le s an d
la y ca bl es a cc or di ng t o th e mo un ti ng pa pe r.
Wiring Hole
NC LOCK
-
12
FR 107
(2) Remove the screw on the bottom
(1) Post the mounting template on the
wall.Drill the holes according to
the marks on the template (holes
for screw and wiring).
(3) Take away the back plate.
+
of device.
NO LOCK
BUT
ULOCK=12V, I-ILOCK>1A…… ①
And the lock is near to the device.
NO
COM
NC
AL+
AL-
+
(2) Does not share power with the lock:
-
GND
+
BELLBELL+
SEN
GND
DC12V
DC power
-
BUT
+
FR 107
(4) Fix the back plate on the wall
according to the mounting paper.
(5) Fix the device to the back plate.
+
-
Device does not shares power with the lock:
DC12V
FR 107
+
NO LOCK
BELLBELL+
SEN
GND
BUT
DC power
B . ULOCK ≠12V;
C. The lock is far apart from the device.
NO
COM
NC
AL+
AL-
+
A. ULOCK =12V I-ILOCK ≤ 1A;
with ‘NO’ terminal, and the NC LOCK is connected with ‘NC’ terminal.
Access Control System Function
(1) If a registered user verified, the device will export the signal
to unlock the door.
TCP/IP
⑦
RS232/RS485 Converter
NC LOCK
NO
COM
NC
AL+
AL-
+12V
GND
(1) The system supporst NO LOCK and NC LOCK. For example the NO LOCK (normally open at power on) is connected
2. Structure and Function
Exit Button
⑤
(2) Door sensor will detect the on-off state. If the door is un-
(2) When the Electrical Lock is connected to the Access Cont rol System, you need to parallel one FR107 diode (equipped
in the package) to prevent the self-inductance EMF affecting the system, do not reverse the polarities.
4. Connected with other parts:
expected opened or improperly closed, the alarm signal
④
(digital value) will be triggered.
Door Bell
Lock Sensor
(3) As the d evice is removed illegally , it will output an alarm signal.
SEN
(4) External card reader is supported.
Door Bell External Reader
Exit Button
Alarm Power
(5) External exit button is supported, it is convenient to open the
Alarm
door inside.
(6) External door bell is supported.
③
Alarm
(7) Supports RS485 , TCP/IP modes to connect with PC. One PC can
manage multiple devices.
Input DC 12V, 500mA (50mA standby)
BELL+
Positive is connected with ‘+12V’, negative is connected
with ’GND’ (do not reverse the polarities).
GND
BUT
EXIT BUTTON

5. Connected with Power:
BELL-
EXIT BUTTON
⑥
②
FR 107
NO
COM
NC
AL+
AL-
+12V
①
Device shares power with the lock:
BELLBELL+
SEN
GND
DC12V
+
RS485
+12V
GND
-
BUT
10
11
+
+12V
GND
-
Multi-Biometric Mounting Paper
(only for your reference)
NO
COM
NC
AL+
AL-
+
Door Sensor
-
+
-
DC12V
Voltage output ≤ DC 12V for Alarm
①:‘I’: device output current, ‘ ULOCK
ILOCK ’: lock voltage,’ ’: lock current
+12V
GND
!
6. Wiegand Output
Warning: No operating with power on
7. Wiegand Input
The device supports standard Wiegand 26 output,
The device has the function of Wiegand signal input . It s upports to
as a reader device it has a very good compatibility.
connect with an independent card reader. They are installed each
side of the door, to control the lock and access together.
(2) RS485 Mode:
485+
485-
Please use specified RS485 wire, RS485 active converter and
bus-type wiring.
485+ 485-
Terminals:
+12V
485Access Control
12Vout
485+
GND
GND
IWD1
TXD
IWD0
DATA1
DATA1
DATA0
Terminals
PC Serial Ports
485+
RS485+
485-
RS485-
RS485 Bus
485+
485-
485+
485-
RS485
Converter
RLED
RXD
RLED
GND
DATA0
GND
GND
GLED
WD 0
BEEP
GLED
BEEP
(3) TCP/IP Mode:
WD 1
(1) Please keep the distance between the device and Access Control or Card Reader less than 90 meters(Please use
Wiegand signal extender in long distance or interference environment).
(2) To keep the stability of Wiegand signal, connect the device and the Access Control or Card Reader in same ‘GND’
in any case.
(A) Crossover cable: The device and PC connected
directly.
(B) Straight cable: The device and PC connected to
LAN/WAN through switch/Lanswitch.
PC
8.Other Functions
Switch
IP Address:192.168.1.100
Subnet Mask:255.255.255.0
(1) Manual Reset:
…
If the device does not work properly because of misoperation or
other abnormality, you can use ‘Reset’ function to restart it.
Side View
Back View
IP Address:192.168.1.124
Operation: Remove the black rubber cap, then stick the Reset button
Subnet Mask:255.255.255.0
hole with a sharp tool (the tip diameter less than 2mm).
(2) Recovery Factory Settings:
You can use the tamper switch to recovery factory setting, such
as device number, system password, IP address, RS485 address,
etc. More information please refers to the user manual.
10. Cautions:
Operation: Press the tamper switch three times after the alarm being
triggered 30 seconds but no more than 60 seconds.
Reset Button
Tamper Switch
Note: The user data won’t be cleared.
(1)Power cable is connected after all the other wiring. If the device is working abnormally, please shut down the power
first, then make the necessary check . Kindly reminds you that any hot-line work may damage the device, and
it is not included in the warranty.
(2)We recommend the 3A/12V DC Power supply. Please contact our technical staff for details.
9. Communication
(3 )Please read the terminals description carefully and wiring by rule strictly. Any damage caused by improper
operations will not under warranty.
There are three modes that the PC software communicate
and exchange information with the device: RS232, RS485
and TCP/IP, and the last two mode support remote control.
(1) RS232 Mode:
(4)Keep the exposed part of wire less than 5mm, to avoid unexpected connection.
Terminals:
Terminals
PC Serial Ports
GND
RXD
Pin5-Gnd
Pin3-Txd
TXD
Pin2-Rxd
(5)Please connect the ‘GND’ before all the other wiring especially under the environment, to prevent the overlarge
instantaneous electrostatic to damage device.
(6)Do not change the cable type because of long distance between the power and the device.
(7) Please use specified RS485 wire, RS485 active converter and bus-type wiring.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement